Boss Audio Systems Music Pedal Boss RV 5 User Manual

Owner’s Manual

AC DC

AC & BATTERY

POWERED

FET

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

● This high-quality, multifunction digital reverb gives you the quality of a studio effect, but

condensed into a compact pedal.

● Models the sound of the spring reverb from Accutronics, a name synonymous with spring

reverb. The emulation on modeling is so realistic that even the sound of the oscillations re-

sulting from the mutual interference between dual springs is reproduced.

● Comes with a completely new “modulate” feature for the reverb, which adds modulation

to the hall reverb, producing an extremely pleasant reverb sound.

● Includes a new type of “gate reverb.” This reverb produces a uniquely distinctive effect

which condenses the reverberation sound.

● Thanks to a 2-in/2-out stereo configuration, the RV-5 offers three dimensional reverb

sound.

* All product names mentioned in this document are trademarks or registered trademarks of their respective

owners. These names, as used in this manual, are for the purpose of accurately describing the sounds

created with modeling.

Download from Www.Somanuals.com. All Manuals Search And Download.

Panel Description

fig.01

1. AC Adaptor Jack

1 2

Accepts connection of an AC Adaptor (op-

tionally available BOSS PSA-Series). By us-

ing an AC Adaptor, you can play without

being concerned about how much battery

power you have left.

* As soon as you connect the AC adaptor, the unit

is turned on.

* If there are batteries in the unit while an AC

adaptor is being used, normal operation will

continue should the line voltage be interrupted

(power blackout or power cord disconnection).

* Use only the specified AC adaptor (PSA-Series).

Download from Www.Somanuals.com. All Manuals Search And Download.

Panel Description

2. CHECK Indicator

4. INPUT-A (MONO) Jack

This indicator shows whether an effect is

ON/OFF, and also doubles as the Battery

Check indicator. The indicator lights when

an effect is ON.

INPUT-B Jack

These jacks accept input signals (coming

from a guitar, some other musical instru-

ment, or another effects unit).

* If this indicator goes dim or no longer lights

while an effect is ON, the battery is near

exhaustion and should be replaced immediately.

For instructions on changing the battery, refer

to “Changing the Battery” (p. 12).

* The unit’s functions differ according to how it is

connected. Refer to “Outputting Only the

Effect” (p. 11).

* When running the unit on battery power, the

INPUT-A (MONO) and INPUT-B jacks double

as power switches. Power to the unit is turned

on when you plug into the INPUT-A (MONO)

or INPUT-B jack; the power is turned off when

the cable is unplugged. Be sure to disconnect

any cord plugged into the INPUT-A (MONO)

or INPUT-B jack when not using this effects

device. When the AC adaptor is used, the power

remains on at all times, and this function is

disabled.

* The CHECK indicator shows whether the effect

is being applied or not. It does not indicate

whether the power to the device is on or not.

3. OUTPUT-A (MONO) Jack

OUTPUT-B Jack

The output jacks are used to connect the unit

to an amplifier or another effects unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Panel Description

fig.02

5. Pedal Switch

Used for switching effects on/off, and for in-

putting the tempo.

6. Thumbscrew

When this screw is loosened, the pedal will

open, allowing you to change the battery.

* For instructions on changing the battery, refer

to “Changing the Battery” (p. 12).

7. E.LEVEL (effect level) Knob

This adjusts the volume of the effect sound.

Turn the knob to the right (clockwise) to in-

crease the effect sound.

Download from Www.Somanuals.com. All Manuals Search And Download.

Panel Description

PLATE:

8. TONE Knob

This simulates the sound of a plate echo (a

type of reverb that uses the vibrations of a

metal plate). It provides a metallic-sounding

reverberation with an extended high end.

This adjusts the tone of the reverb sound.

The more you turn the knob to the right

(clockwise) of center (standard), the brighter

the sound becomes; turn the knob to the left

of center to create a sound with greater

warmth.

HALL:

This simulates the reverb sound of a larg-

er hall.

9. TIME Knob

This adjusts the length (time) of the reverb

sound.

ROOM:

This simulates the reverb sound of a

smaller room.

GATE:

10. MODE Switch

Produces a uniquely distinctive effect in

which the reverberation sound is con-

densed.

Selects the reverb effect and pedal mode.

* Immediately after the MODE switch is

switched, operating the pedal produces no result.

MODULATE:

SPRING:

This is a completely new reverb that adds

modulation to the hall reverb to produce

an extremely pleasant reverb sound.

This simulates the sound of a guitar

amp’s built-in spring reverb.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

fig.03

AC adaptor

BOSS PSA-series (option)

Keyboard

OUT DC 9V/200mA

Electric

Guitar

Guitar Amplifier

* Be sure to lower the output level of any device being connected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

* When running the unit on battery power, inserting a plug into the INPUT-A (MONO) or INPUT-B Jack

will automatically switch the unit on.

* The use of an AC adaptor is recommended as the unit’s power consumption is relatively high. Should you

prefer to use batteries, please use the alkaline type.

* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and

turn off the power on all devices before making any connections.

* If there are batteries in the unit while an AC adaptor is being used, normal operation will continue should

the line voltage be interrupted (power blackout or power cord disconnection).

* Once the connections have been completed (p. 8), turn on power to your various devices in the order

specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to

speakers and other devices.

When powering up:

Turn on the power to your guitar amp last.

When powering down: Turn off the power to your guitar amp first.

* Always make sure to have the volume level turned down before switching on power. Even with the volume

all the way down, you may still hear some sound when the power is switched on, but this is normal, and

does not indicate a malfunction.

* When operating on battery power only, the unit’s indicator will become dim when battery power gets too

low. Replace the battery as soon as possible.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating the Unit

fig.05

1. When you have made the necessary con-

nections (p. 8), depress the pedal switch

to turn the effect on. (the CHECK indica-

tor turns red.)

* The unit’s functions differ according to how it is

connected. Refer to “Outputting Only the

Effect” (p. 11).

2. Select the mode with the MODE switch.

3. Adjust the reverb time with the TIME

knob.

4. Adjust the tone of the reverb sound with

the TONE knob.

5. Adjust the effect volume level with the

E.LEVEL knob.

Download from Www.Somanuals.com. All Manuals Search And Download.

Outputting Only the Effect

By plugging into INPUT-B, you can have only the effect sound be output (the direct sound is

not output).

* When the effect is off, the output from OUTPUT-A and OUTPUT-B is muted.

Mixer

Guitar Amplifier

* Make sure the input/output levels of devices being connected are matched appropriately.

* When using a guitar amp to send/return the direct sound as well, connect to INPUT-A (MONO).

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing the Battery

When the indicator goes dim or no longer

lights while an effect is on, it means that the

battery is nearly dead and must be replaced.

Replace the battery following the steps below.

1. Loosen the thumbscrew at the front of

the pedal, then lift the pedal upwards to

open the unit.

* The thumbscrew can be left in the pedal while

changing the battery.

The use of an AC adaptor is recommended as the

unit’s power consumption is relatively high. Should

you prefer to use batteries, please use the alkaline type.

2. Remove the old battery from the battery

housing, and remove the snap cord con-

nected to it.

fig.09

Thumbscrew

Pedal

3. Connect the snap cord to the new battery,

and place the battery inside the battery

housing.

* Be sure to carefully observe the battery’s polarity

(+ versus –).

Spring Base

Battery Snap

Cord

Coil Spring

Guide Bush

Hole

4. Slip the coil spring onto the spring base on

the back of the pedal, then close the pedal.

* Carefully avoid getting the snap cord caught in

the pedal, coil spring and battery housing.

Battery

Snap

Battery Housing

5. Finally, insert the thumbscrew into the

9V Battery

guide bush hole and fasten it securely.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Power won’t come on / CHECK indicator doesn’t light:

● Is the specified adaptor (PSA-series;

● Is the guitar connected properly to the

sold separately) properly connected?

INPUT-A (MONO) or INPUT-B jack?

Check the connection once more (p. 8).

* Never use any AC adapter other than one

specified for use with the RV-5.

* To prevent useless depletion of the battery when

the unit is running on battery power, the power

is switched on only when a cable is plugged in to

the INPUT-A (MONO) or INPUT-B jack.

● Is the battery low or dead?

Replace with a new battery (p. 12).

* The CHECK indicator shows whether the effect

is being applied or not. It does not indicate

whether the power to the device is on or not.

* The battery that was supplied with the unit is

for temporary use, intended primarily for testing

its operation. For extended use, we suggest

replacing it with an alkaline battery.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

No sound / Low volume:

Sound is distorted:

● Is the RV-5 properly connected to your

● Is the battery low?

instrument?

As the battery is drained, the CHECK in-

dicator dims, and the RV-5 may start to

function incorrectly. Replace with a new

battery (p. 12).

Check the connection once more (p. 8).

● Is the volume turned down on any guitar

amp or effects device you have connect-

ed?

● Could the level of the sound being input

be excessive?

Check the settings of the connected device.

With some guitars, distortion may be pro-

duced. Be careful of your guitar’s output

level.

● Do you have a stereo plug connected?

This device will not operate properly with

stereo plugs. Please use mono plugs.

● Are you connected only to INPUT-B?

The direct sound is not output when you

connect only to INPUT-B. The outputs are

muted when the effect is off, and no

sound is output (p. 11).

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Samples

Spring Reverb

Concert Hall

You can derive more of the spring reverb’s char-

acteristic ambience by muting the lower strings.

Bright Reverb

Deep Reverb

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Samples

Room

Fat Sound

Effective when TIME is matched with the phrase’s

tempo. This yields an even fatter sound when

used in combination with distortion effects.

Garage Sound

Chorus Effect

Adds a sense of greater breadth and depth to ar-

peggios played with a clean sound.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

RV-5: Digital Reverb

Nominal Input Level ......................-20 dBu

Input Impedance.............................1 MΩ

Nominal Output Level...................-20 dBu

Output Impedance..........................1 kΩ

Recommended Load Impedance.....10 kΩ or greater

Residual Noise.................................-93 dBu (IHF-A, Typ.): All knobs at center position

Controls ............................................Pedal Switch, E.LEVEL knob, TONE knob, TIME knob,

MODE switch

Indicator ...........................................CHECK Indicator (Serves also battery check indicator)

Connectors .......................................INPUT-A (MONO) jack, INPUT-B jack,

OUTPUT-A (MONO) jack, OUTPUT-B jack,

AC adaptor jack (DC 9 V)

Power Supply ..................................DC 9 V: Dry battery (9 V type) S-006P/9 V (6F22/9 V)

Dry battery (9 V type) 6AM6/9 V (alkaline)

AC Adaptor

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Current Draw ..................................50 mA (DC 9 V)

* Expected battery life under continuous use:

Carbon: 2 hours, Alkaline: 6 hours

These figures will vary depending on the actual conditions of use.

Dimensions ......................................73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight. .............................................440 g / 1 lb (including Battery)

Accessories.......................................Owner’s Manual

Leaflet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,”

and “Information”)

Dry battery (9 V type) S-006P/9 V (6F22/9 V)

* The battery that was supplied with the unit is for temporary use-

intended primarily for testing its operation.

We also suggest replacing this with an alkaline dry cell.

Options .............................................AC Adaptor PSA-Series

* 0 dBu = 0.775 Vrms

* In the interest of product improvement, the specifications and/or appearance of this unit are subject to

change without prior notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

For EU Countries

For the USA

This product complies with the requirements of European Directive 89/336/EEC.

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

–

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Unauthorized changes or modification to this system can void the users authority to operate this equipment.

This equipment requires shielded interface cables in order to meet FCC class B Limit.

For Canada

NOTICE

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

AVIS

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Download from Www.Somanuals.com. All Manuals Search And Download.

G6017360

Download from Www.Somanuals.com. All Manuals Search And Download.

Black Decker Cordless Drill LDX220 User Manual
Bolens Pole Saw TP720r User Manual
Bosch Power Tools Power Hammer 11536VSR User Manual
Boss Audio Systems Speaker System MC450 User Manual
Canon Photo Printer MP 190 Pixma User Manual
Casio Clock DQ 542 User Manual
Chamberlain Garage Door Opener 2580C 1 2 HP User Manual
Channel Plus Home Theater Server SVS 52 User Manual
Chauvet Automobile Accessories F 1700 User Manual
Chromalox Electric Heater PF452 4 User Manual