INSTALLATION AND OPERATING INSTRUCTIONS FOR AUTOMATIC
INSTANTANEOUS TYPE WATER HEATERS FOR USE WITH NATURAL AND
LIQUEFIED PETROLEUM GAS
MODEL 125B LP and 125B NG (Flow Modulated)
Suitable for heating potable water only
Not approved for space heating purposes
Intended for variable flow applications with steady cold water inlet temperatures only
WARNING
If the information in this manual is not followed exactly, a
fire or explosion may result causing property damage,
personal injury or death.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable,
combustible or corrosive vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electrical switch; do not use any
phone in your building.
- Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the fire
department.
- Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
TABLE OF CONTENTS
Specifications....................................... Page 2
Rules for safe operation..................... Page 4
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury or
property damage. Refer to this manual. For assistance
or additional information consult a qualified installer,
service agency or the gas supplier.
Upon completion of the installation, these instructions
should be handed to the user of the appliance for future
reference.
Locating the Heater ............................ Page 4
Combustion Air Requirements .......... Page 5
Mounting the Heater ........................... Page 6
Venting the Heater .............................. Page 7
Gas Connections ..............................Page 10
Water Connections ...........................Page 12
Safety before lighting the pilot .......Page 12
Lighting instructions ..........................Page 13
Setting water temperature ...............Page 13
Maintenance & Service....................Page 13
Trouble Shooting................................Page 14
Diagram of AquaStar ........................Page 19
Components and Parts List ............ Page 20
In the Commonwealth of Massachusetts this product
must be installed by a licensed plumber or gas fitter.
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT VIEW
SIDE VIEW
MINIMUM INSTALLATION CLEARANCES FROM COMBUSTIBLE AND NON
COMBUSTIBLE MATERIALS FOR ALCOVE OR CLOSET INSTALLATIONS
MODEL 125B
TOP (A)
12 "
4 "
FRONT (B)
BACK
0 "
SIDES
4 "
FLOOR (C)
VENT DIAMETER
12 "
5 "
AQUASTAR MODEL 125B
6 720 607 030
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL RULES TO FOLLOW
FOR SAFE OPERATION
PROPER LOCATION FOR INSTALLING YOUR
HEATER
Carefully select the location of your new heater. For your
safety and for proper heater operation, you must provide an
abundant supply of combustion air and a proper venting
installation.
The heater may still operate even when improperly vented.
It will, however, be less efficient and could eventually damage
the heater. It could even result in human sickness or death
due to oxygen deprivation and carbon monoxide poisoning.
Follow the guidelines below:
1. You should follow these instructions when you install your
heater. In the United States: The installation must conform
with local codes or, in the absence of local codes, the
National Fuel Gas Code ANSI Z223.1/NFPA 54.
In Canada: The Installation should conform with CGA
B149.(1,2) INSTALLATION CODES and /or local installation
codes.
2. Carefully plan where you install the heater. Correct
combustion air supply and flue pipe installation are very
important. If not installed correctly, fatal accidents can be
caused by lack of air, carbon monoxide poisoning or fire.
1. Place your heater as close to a vent or chimney as
possible.
2. National building codes require that you do not install
this appliance in bathrooms, bedrooms, unvented closet or
any occupied rooms normally kept closed.
3. The place where you install the heater must have enough
ventilation. The National Fire Codes do not allow gas fired
water heater installation in bathrooms, bedrooms or any
occupied rooms normally kept closed. See the section below
on locating the heater.
3. Simultaneous operation of other appliances such as
exhaust fans, ventilation systems clothes dryers, fireplaces
or wood stoves could create a vacuum effect in your home
which could cause dangerous combustion by-products to
spill back into your home rather than venting to the outside
through the flue. Confirm that your Aquastar is venting
properly when all these other appliances are running. See
section on venting.
4. You must vent your heater. See section on Venting, Page
6.
5. The appliance must be disconnected from the gas supply
piping system during any pressure testing at pressures in
excess of 1/2 Psig (3.5 kPa).
The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or more than 1/2 Psig (3.5Kpa). The
appliance and its gas connection must be leak tested before
placing the appliance in operation.
Do not obstruct the flow of combustion and ventilation
air to the appliance. If installed near a clothes dryer it is
very important that the dryer be properly vented. Failure to
properly vent a dryer could result in a gradual accumulation
of lint on the water heater fin coils and burners, leading to a
dangerous condition of vent blockage and poor unsafe
combustion.
6. Keep water heater area clear and free from combustibles
and flammable liquids. Do not locate the heater over any
material which might burn.
4. Your hot water lines should be kept short to save energy.
It is always best to have hot water lines insulated.
7. Correct gas pressure is critical for the optimum
operation of this heater (see specifications on page 2). Gas
piping must be sized to provide the required pressure at the
maximum output of the heater, while all the other gas
appliances are in operation. Check with your local gas
supplier, and see the section on connecting the gas supply.
5. This product is neither designed nor approved for outside
installations. This product is not approved for manufactured
homes (mobile home), recreational vehicles (RV) or boats.
Reference ANSI Z21.10.3.
WARNING: The water in this water heater is cold and
always remains cold except for the times that hot water is
being used DO NOT INSTALL IN AN AREA WHERE IT
COULD FREEZE.
8. Should overheating occur or the gas supply fail to shut
off, turn off the gas supply at the manual gas shut off valve
on the gas line.
9. Do not use this appliance if any part has been underwater.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been underwater.
Drain the heater entirely if freezing temperatures are
anticipated in area where heater is installed by disconnecting
both the inlet and outlet water connections from the heater
(disconnect the outlet flex line from where it connects to
the copper heat exchanger). Additionally, remove the drain
plug under the water valve. See Fig 1.
4
6 720 607 030
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Vents
(10 ¾ X 10 ¾ in. each)
125B
Fig. 1 - Water heater drain plug
WARNING: Flammable materials, gasoline,
pressurized containers, or any other items or articles
that are potentially fire hazards must NOT be placed on
or adjacent to the heater. The appliance area must be
kept free of all combustible materials, gasoline and other
flammable vapors and liquids.
Air Vents
125B
(5 ½ X 5 ½ in. each)
Appliances located in confined spaces:
The confined space must be provided with two permanent
openings, one commencing within 12 inches of the top and
one commencing within 12 inches of the bottom of the
enclosure. Each opening must have a minimum free area of
one square inch per:
- 1000 Btu/hr if all air is taken from inside the building.
- 2000 Btu/hr if all air is taken from the outside by horizontal
ducts.
- 4000 Btu/hr if all air is taken from the outside by direct
openings or vertical ducts.
Or the confined space must be provided with one permanent
opening or duct that is within 12 inches of the ceiling of the
enclosure. This opening must have a minimum free area of
one square inch per:
COMBUSTION AIR REQUIREMENTS
The AquaStar water heater holds cold water in its copper
heat exchanger and brass water valve when not in use.
Because of this, any cold air that comes down through the
unit’s vent pipe is capable of freezing these components.
This Installation Manual specifies the minimum vertical vent
pipe and the amount of combustion air required for this unit.
When all requirements are followed, the unit will operate
properly and safely. However, there may still be a risk of
freezing due to negative draft if all the combustion appliances
in the area are not being supplied with a sufficient amount
of make-up air. A wood stove or furnace can rob the make-
up air in the AquaStar’s vent pipe, leaving the cold infiltrating
air capable of freezing the cold water in the AquaStar heat
exchanger. More make up air is the solution. Follow the
instructions on venting and checking adequacy of make up
air. A HVAC specialist should be used to design solutions
for providing more make-up air if necessary.
- 3000 Btu/hr if all air is taken from the outside by a direct
opening or vertical duct.
Louvers, grills and screens have a blocking effect. If the
effective free area is not known, increase the sizes of your
openings by 75% if your louvers are wood and by 30% if
your louvers are metal. Refer to the National Fuel Gas Code
for complete information. In buildings of tight construction
all air should be taken from outside.
Observe the following instructions concerning combustion
air.
CLEARANCES
Appliances located in unconfined spaces:
a) An unconfined space is one whose volume is greater
than 50 cubic feet per 1000 Btu per hour of the combined
rating of all appliances installed in the space. That would
be 5850 cubic feet for the AquaStar 125B alone.
The Aquastar 125 B is design certified for installation on a
combustible wall and for installation in an alcove or closet
with the minimum clearances to combustible and non -
combustible construction listed below
A. Top 12 inches (306 mm)
b) In unconfined spaces in buildings of conventional frame,
masonry, or metal construction, infiltration is normally
adequate to provide air for combustion, ventilation, and
dilution of flue gasses.
B. Front 4 inches (102 mm)
C. Back 0 inches
D. Sides 4 inches (102mm)
E. Bottom 12 inches (306 mm)
Clearance from vent is dependent upon the clearance rating
of the venting material used. For example: type B-1 vent is
approved for 1 inch clearance.
6 720 607 030
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Typically, the minimum clearence to combustible The incandescent particle tray (shipped loose in the carton
with the water heater) must be attached at the bottom of
the water heater front cover at the time of installation. Use
the screws provided. See figure 3
materials should not be less than 6“ for single wall flue
pipe. Note that this clearance can be reduced if combustible
materials are protected as per table VI of the National Fuel
Gas Code or if Type B gas vent is used.
MOUNTING INSTALLATION
The Aquastar 125 B is design certified for mounting on a
wall.
Secure the two L shaped hooks, which are provided with
heater, to a wall surface. Place them 13 ¼” apart as shown
in Fig. 2.
SCREWS
INCANDESCENT PARTICLE TRAY
Do not install this appliance on a carpeted wall or over floor
covering which is combustible, such as carpet. The heater
must be mounted on a wall using appropriate anchoring
materials. If wall is a stud wall sheathed with plasterboard, it
is recommended that support board(s), either 1x4’s or
1/2" (minimum) plywood first be attached across a pair
of studs and then the heater should be attached to the
support boards. See Fig. 2.
Fig. 3 - Incandescent Particle Tray Illustration
Expansion and contraction of piping due to changing water
temperature in the pipes imparts movement to the heater
which, if mounted directly to a brittle, friable board, such as
plasterboard, can cause failure of mounting.
In earthquake-prone zones, CEC recommends that installers
use a large washer and lag screw through the existing holes
used to hang the heater to affix the upper third of the heater
to the mounting board. To affix the lower third of the heater,
CEC recommends that two new holes be drilled in the
heater’s frame, each one 16 inches below the top two holes,
and that washers and lag screws be used to secure the
lower portion of the heater to a spacing board.
Before installing the unit, be certain you have the correct
heater for your type of Gas – Propane or Natural Gas.
Identification labels are found on the shipping box, and on
the rating plate which is located on the right side panel of
the cover. Also, each burner orifice is stamped with a number
(79 for LPG and 120 for Natural Gas).
WALL STUDS
13 ¼”
SUPPORT
BOARD
1” X 4”
SPACE BOARD
Fig. 2 - Mounting the Heater
6
6 720 607 030
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING
Vent pipe connection. WARNING: Do not reduce the vent pipe size. See Fig. 4 for high altitude installations
The heater must be vented to the outside following all local ordinances and specifications for installing a gas appliance
vent or chimney. The heater must be located as close as practicable to a vertically rising chimney or vent that has a listed
vent cap at its termination point. The venting system must be designed and constructed so as to develop a positive flow
adequate to remove flue gasses to the outdoors.
Consult the National Fuel Gas Code if the vent will have elbows or share venting with another natural draft appliance.
The heater should never be common vented with a mechanically vented appliance. Single wall vent pipe is not
recommended, if used consult the National Fuel Gas Code.
Horizontally venting to a sidewall vent terminator or a vertically constructed vent stack along an outside wall of a building
is not permissible. A Powervent (Model AQ-1), with a proof-of-draft safety interlock device, is required and is available in
order to sidewall vent. Contact your dealer. In the Commonwealth of Massachusetts: Powervented applications must
utilize proof-of-draft safety interlock device.
VERTICAL GAS VENT: A 5 inch diameter gas vent constructed of double wall Type B gas vent is recommended. 6 inch is
required in elevations greater than 2000 feet, see Fig. 4. Any gas vent section that is greater than 45 degrees from the
vertical is considered horizontal. Horizontal sections must slope upwards at least ¼ inch for every foot of its horizontal
length and be properly supported. Keep the horizontal section short and avoid too many elbows. The minimum vertical gas
vent height allowed is 6 feet; horizontal vent connectors and elbows are not to be considered in the total gas vent height.
All gas vent sections must be secured to each other with sheet metal screws and be properly supported.
The gas vent constructed of double wall Type B gas vent must terminate above the roof surface with a listed vent cap at
a height that’s in accordance with Figure A or B and their table, provided they are at least 8 feet (2.4 m) from a vertical wall
or similar obstruction. All other gas vents that are not able to terminate within the minimum specified height allowed must
terminate not less than 2 feet (0.6 m) above the highest point where it’s passed through the roof and at least 2 feet (0.6
m) higher than any vertical wall or similar obstruction within 10 feet (3.1 m).
LISTED VENT CAP
LISTED VENT CAP
LOWEST DISCHARGE OPENING
H (minimum) height
from roof to lowest
X
discharge opening
12
ROOF PITCH
IS X/12
MINIMUM 6
FEET (1.8M)
MINIMUM 6
FEET (1.8M)
LISTED GAS VENT
ESTABLISH A ONE
FOOT RISE BEFORE
ANY ELBOWS
GAS VENT TERMINATIONS FOR LISTED VENT CAPS
Roof pitch
Flat to 6/12
H (minimum) feet
meters
0.30
0.38
0.46
0.61
0.76
0.99
1.22
1.52
1.83
2.13
2.27
2.44
1.0
1.25
1.5
2.0
2.5
3.25
4.0
5.0
6.0
7.0
7.5
8.0
6/12 to 7/12
Over 7/12 to 8/12
Over 8/12 to 9/12
Over 9/12 to 10/12
Over 10/12 to 11/12
Over 11/12 to 12/12
Over 12/12 to 14/12
Over 14/12 to 16/12
Over 16/12 to 18/12
Over 18/12 to 20/12
Over 20/12 to 21/12
Figure B
Figure A
6 720 607 030
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MASONRY CHIMNEY: Masonry chimneys shall be built and installed in accordance with NFPS 211 or local codes. A minimum
5” diameter gas vent pipe (metal double wall Type B), or an approved clay flue liner or a listed chimney lining system must
be used when venting into a naturally drafting, internal masonry chimney. 6 inch is required in elevations greater than 2000
feet, see Fig. 4. Local codes may require the use of both gas vent and an approved lining system when venting into a
masonry chimney. The Commonwealth of Massachusetts requires the use of a listed liner. Lining systems include approved
clay flue lining, a listed chimney lining system or other approved material that will resist corrosion, erosion, softening, or
cracking from exhaust flue gases at temperatures up to 1800 degrees F. The lining system must be listed for use with
naturally drafting, draft hood equipped gas appliances. Follow local codes and refer to NFGC 54 and NFPA 58.
When connecting the water heater to a masonry chimney the following connector guidelines must be followed for
safe and proper operation: An approved gas vent connector must be attached to the top of the water heater and rise
vertically at least 12” before entering into an approved gas vent connector elbow. Any gas vent section that is greater than
45 degrees from the vertical is considered horizontal. If a horizontal vent connector is to be used to connect the vertical
gas vent connector on the top of the water heater to the masonry chimney, that approved horizontal gas vent connector
must be kept as short as possible and must be sloped upwards at least ¼” per foot of its length. This connector must be
supported throughout its horizontal length. This horizontal gas vent connection may be no greater than 75% of the total
vertical gas flue vent within the chimney. Also, an approved thimble or collar must be used when penetrating a masonry
chimney.
A) Existing INTERIOR Masonry Chimney
The metal gas vent pipe should be permanently mounted inside the masonry chimney. Double wall Type B gas vent is
recommended. The masonry chimney may have to be tile or metal lined before the insertion of the gas vent pipe; check
local codes for clarification. The lining material must be listed for use only with naturally drafting, draft hood equipped gas
appliances. Follow manufactures instructions for installation of listed lining material. You may not vent any other fuel
burning appliances into any free space remaining in the chimney. The minimum vertical gas vent length within the masonry
chimney should be no less than 5 ft (1.5 m); the vent terminator should extend at least 3 feet (0.9 m) above where the
chimney meets the roofline and at least 2 feet (0.6 m) higher than any vertical wall or similar obstruction within 10 feet (3.1
m). The top of the gas vent should have an approved vent terminator. See Figure C.
B) Tile Lined INTERIOR Masonry Chimney
The masonry chimney must have an approved liner, ceramic tile, clay or metal. The masonry chimney must be able to
accommodate the spent fuel gasses; consult a venting HVAC contractor for chimney capacity. A common venting like-fuel
appliance into this lined masonry chimney is permissible. The chimney’s diameter must be large enough to adequately draft
the spent fuel gasses. A venting HVAC contractor will be required to spec a chimney system. The minimum vertical
chimney length should be no less than 5 ft (1.5 m); the termination point should extend at least 3 feet (0.9 m) above where
the chimney meets the roofline and at least 2 feet (0.6 m) higher than any vertical wall or similar obstruction within 10 feet
(3.1 m). See Figure C.
C) EXTERIOR masonry Chimney
Refer to the National Fuel Gas Code and consult a local venting HVAC contractor.
MASONRY CHIMNEYS
LISTED VENT CAP
GAS
VENT
VENT CONNECTOR
ESTABLISH A ONE
FOOT RISE BEFORE
ANY ELBOWS
Figure C
8
6 720 607 030
Download from Www.Somanuals.com. All Manuals Search And Download.
To check the draft:
Close all doors and windows to the outside.
Turn on all appliances that force air out of the building.
These include all exhaust/ventilation fans, furnaces, clothes
dryers, wood burning stoves, etc.
5” X 6” ADAPTOR
USED ON HIGH ALTITUDE
Open all doors between the AquaStar and these other
appliances.
With the control knob set fully clockwise and strong hot
water flow rate, run the unit for at least 10 minutes. The
125B is equipped with a Flue Gas Sensor; it’s mounted on
the right side of the draft diverter (Flue Gas Sensor #20 on
page 17). If the main burners and the pilot flame shut off
during this test it is because the Flue Gas Sensor has
detected inadequate venting. This is a serious health hazard
and must be corrected. Poor venting can result in soot
building up inside the heater, overheating of the heater and
freezing of the heat exchanger in a non-freezing environment
when not in use, which is all a result of negative air flow.
Additional combustion air and/or improved venting is
necessary to correct this.
Fig. 4 - Vent Adaptor for High Altitude Installations
WARNING: Failure TO INCREASE THE VENT SIZE
TO SIX INCHES AND/or assure that the manifold pressure
is set to proper value listed for applications at high altitudes
will cause unsafe venting, asphyxiation, and will void CSA
Certification.
WARNING
Note: The burners of an instantaneous “on demand” water
heater such as the AquaStar are only on at the time that
hot water is actually being used, the vent pipe is therefore
cold except for the short durations when hot water is being
used, it is therefore very important that the venting and air
supply be adequate to provide a good positive draft as soon
as the burners turn on.
The AquaStar 125B instantaneous water heaters have built-
in draft diverters and are designed for indoor installation
only. The draft diverter outlet must be connected to an,
unobstructed vent of the same size, or larger.
In Canada, CAN/CGA-B149 Installation Code for detailed
requirements
In U.S.A., ANSI Z223.1 - NFPA 54, National Fuel Gas
Code for detailed requirements.
The vent connection for the Aquastar 125B is 5 inches.
However, for installations at high altitude (over 2000 feet
above sea level) a six inch vent is required. A 5” by 6” vent
adaptor must be affixed to the flue collar of the Aquastar
with at least two screws. See Fig. 4.
6 720 607 030
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS LINE SIZING
GAS CONNECTIONS
-It is strongly recommended that the Natural Gas pipe
be Black Iron pipe the entire distance from the outside
meter to the inlet of the Aquastar regulator. 1/2” Black
Iron pipe up to 10 feet, 3/4” Black Iron pipe up to 40 feet
and 1” Black Iron pipe up to 150 feet distances. Flex line
tubing is NOT recommended, but if used then oversize
it.
-It is strongly recommended that the LP Gas pipe be
semi-rigid copper or Black Iron pipe from the outside
regulator to the inlet of the Aquastar regulator. For semi-
rigid copper piping: 5/8” up to 20 feet and 3/4” up to 60
feet distances. For Black Iron piping: 1/2 “ up to 45 feet
and 3/4” up to 160 feet distances. Flex line tubing is NOT
recommended, but if used then oversize it.
NOTE: The Aquastar 125 B is supplied with a gas pressure
regulator that must be installed on the heater before
attaching the gas supply line. See fig. 5. Failure to install
the gas regulator as shown in figure 5 will be a violation
of CSA certification of the unit. The regulator supplied
with the heater is preset for the gas shown on the rating
plate to the correct pressure. It is an appliance level
regulator designed for (low inlet) pressure (less than 1/
2 Psig or 15” W.C.)
DO NOT connect to an unregulated or high pressure
propane line or to a high pressure commercial natural
gas line.
THESE FIGURES ARE FORAQUASTAR SUPPLY ONLY, ALL
OTHER APPLIANCES IN THE BUILDING WILL NEED TO
BE INCLUDED IN THE PIPE SIZING.
National Fuel Gas Code requires that a sediment trap (drip
leg) be installed on gas appliances not so equipped. The
drip leg must be accessible and not subject to freezing
conditions. Install in accordance with the recommendations
of the serving gas supplier.
GAS INLET PIPE
PRESSURE TAP
PLASTIC VENT CAP
WARNING: The heater must be disconnected from
the gas supply piping system during any pressure testing of
that system at test pressures in excess of 0.5 psig.
The water heater must be isolated from the gas supply piping
system by closing the manual shutoff valve during any
pressure testing of the gas supply piping system at test
pressures equal to or more than 0.5 psig.
The water heater, including the pressure regulator provided
with it, must not be operated at gas supply pressures in
excess of 0.5 psig. If overpressure has occurred, such as
through improper testing of the gas lines or malfunction of
the supply system, the gas valve and regulator must be
checked for safe operation. Make sure that the regulator
vent is protected against blockage.
When your connections are made, check for gas leaks at
all joints (not just the ones you made). Apply some soapy
water to all gas fittings and gas valve. Soap bubbles are a
sign of a leak.
NOTE: Do not apply soap solution to pilot filter screen or
pilot orifice area. If you have a leak, shut off the gas. After
verifying that required gaskets are in place, tighten
appropriate fittings to stop leak. Turn the gas on and check
again with a soapy solution. Never test for gas leaks using
a match or flame.
PRESSURE REGULATOR
(with directional arrow on
reverse side pointing
upward)
Fig. 5 - Installation of Gas Pressure Regulator
The pressure regulator provided with the heater is adjusted
to deliver the proper gas pressure (as indicated on the rating
plate and in the manual for altitude up to 2000 feet (660
meters) above sea level. On appliances being installed above
2000 ft (660 meters) elevation, the inlet gas pressure should
be set at installation to the value shown below.
NOTE: The gas pressures specified below refer to
pressures taken at the pressure tap on the gas inlet pipe
just above the regulator (See Fig. 5).
These readings should be taken while the heater is
operating at full input — i.e. maximum water flow with
the temperature dial selector turned all the way clockwise.
MAXIMUM INLET GAS FLOW PRESSURE SETTING
Altitude
Natural Gas
inches W.C:
5.7"
Liquid Propane
inches W.C:
10.5"
0' - 2.000 ft
2.000 ft - 4.500 ft
4.6"
8.4"
Above 4.500 ft consult your local gas supplier.
10
6 720 607 030
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS PIPING, CONNECTIONS and Gas Regulator
Before connecting the gas supply, check the rating plate on the right side of the front cover to be sure that the heater is
rated for the same gas to which it will be connected.
In the United States: The installation must conform with local codes or, in the absence of local codes, the National Fuel
Gas Code ANSI Z223.1/NFPA 54.
In Canada: The Installation should conform with CGA B149 INSTALLATION CODES and /or local installation codes.
GAS LINE SIZING
FOR NATURAL GAS
Maximum Capacity of pipe in Cubic Feet of Gas per Hour
for Gas Pressure of 0.5 Psig or less and a Pressure drop of
0.3 in Water Column.
Follow boxed numbers for piping just one Aquastar 125B
(example: 3/4” B.I. Natural Gas pipe for 30 ft. will handle
152,000 btu’s). For multiple appliances combine the total
btu input load and then refer to applicable chart below.
(Based on a 0.60 Specific Gravity Gas) Btu numbers given
in thousands.
Nominal
Length of Black Iron Pipe, Feet
Iron
Pipe
Internal
Size, Diameter
inches inches
10
20
30
40
50
60
70
80
90
100
125
150
175
200
1/4
3/8
1/2
0.364
0.493
0.622
32
72
22
49
92
18
40
73
15
34
63
14
30
56
12
27
50
11
25
46
11
23
43
10
22
40
9
8
8
7
6
21
38
18
34
17
31
15
28
14
26
132
3/4
1
0.824
1.049
278
520
190
350
152
285
130
245
115 105
215 195
96
90
84
79
72
64
59
55
180
170
160
150
130
120
110
100
1 1/4
1 1/2
2
1.380
1.610
2.067
2.469
3.068
4.026
1050
1600
3050
4800
8500
730
590
890
500
760
440 400
670 610
370
560
350
530
320
490
930
305
460
870
275
410
780
250
380
710
225
350
650
210
320
610
1100
2100 1650 1450
3300 2700 2300
5900 4700 4100
1270 1150 1050 990
2 1/2
3
2000 1850 1700 1600 1500 1400 1250
3600 3250 3000 2800 2600 2500 2200
1130 1050 980
2000 1850 1700
4
17,500 12,000 9,700 8,300 7,400 6,80 6,200 5,800 5,400 5,100 4,500 4,100 3,800 3500
Nominal
FOR LP GAS
Iron Pipe
Size,
Black Iron Pipe
Length of Pipe, Feet
Maximum Capacity of Pipe in Thousands of
BTU per Hour of Undiluted Petroleum Gases
(at 11 inches Water Column Inlet Pressure)
(Based on a Pressure Drop of 0.5 Inch Water
Column).
10 20 30
40 50 60 70 80 90 100 125 150
Inches
1/2
275 189 152 129 114 103 96 89 83
78
69
63
3/4
1
567 693 315 267 237 217 196 185 173 162 146 132
107 732 590 504 448 409 378 346 322 307 275 252
1 1/4 220 149 121 103 913 834 771 724 677 630 567 511
1 1/2 330 229 185 155 141 127 118 108 102 976 866 787
2
622 433 346 299 264 239 220 204 192 1811 1606 1496
Copper
Outside
Diameter,
Inch
Length of Tubing, Feet
Maximum Capacity of Semi-Rigid
10 20
39 26
92 62
30
21
50
40
19
41
50
_
60 70 80 90 100
Tubing in Thousands of BTU per Hour of
Undiluted Liquified Petroleum Gases (at 11
inches Water Column Inlet Pressure)
_
_
_
_
_
3/8
1/2
37
79
35 31 29 27 26
72 67 62 59 55
121 112 104 95 90
187 164 155 146 138
(Based on a Pressure Drop of 0.5 Inch Water
Column)
5/8 199 131 107 90
3/4 329 216 181 145 131
7/8 501 346 277 233 198
* Source National Fuel Gas Code NFPA 54, ANSI Z223.1 - No
Additional Allowance is necessary for an ordinary number of fittings
6 720 607 030
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER CONNECTIONS
Install the heater centrally in the building if possible and
make hot water piping runs as short as possible When facing
the heater, the cold water inlet will be on the right and the
hot water outlet on the left..
Although water piping throughout the building may be other
than copper, copper or galvanized piping should be used
when connecting to the heaters ½” male NPT flex connectors
(follow local codes if more stringent). Plastics or other PEX
type plumbing line materials are not suitable for connecting
directly to the water heater. Keep water inlet pipe to no less
than ½” (19.05mm) diameter to allow the full flow capacity.
If the cold and hot connections to the heater are reversed,
the heater will not function.
PIPE PRV TO
APPROPRIATE
DISCHARGE
Fig. 7 - Pressure Relief Valve
The Aquastar 125B is provided with one flexible type
connector that must be connected to the cold inlet fitting of
the water valve as shown in Fig. 6. The union end of the
flexible connector should be attached to the rear inlet port
of the water valve with the supplied washer gasket. No pipe
dope or thread tape is to be used at this joint. The ½” flexible
hot water outlet line is supplied attached to the heater.
Be certain there are no loose particles or dirt in the piping.
Blow out or flush the lines before connecting to the water
heater. Full port valves should be installed on both the cold
water supply and hot water outlet lines to facilitate servicing
the heater (see Fig. 7). For installation on a private well
system with the use of a pressure tank, the lowest pressure
range setting recommended is 30-50 psi (2.07-3.45 bar).
OPERATINGINSTRUCTIONS
Before proceeding with the operation of the heater make
sure that the system is filled with water.
Open the cold water inlet supply to the heater fully.
Open a hot water faucet to permit the water to fill the heater
and the piping and to eliminate the air trapped in the system
Close the hot water faucet after the water flows freely and
all the air has escaped from the system. The water heater is
now ready to operate.
FOR YOUR SAFETY READ BEFORE LIGHTING
THE PILOT
Warning: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
A. This appliance has a piezo-igniter for lighting the pilot
burner. When lighting the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electric switch; do not use any phone
in your building
Fig. 6 - Water valve and water connector, top view
- Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the fire
department.
Connecting the pressure relief valve (PRV)
A listed pressure relief valve supplied with the heater must
be installed at the time of installation. No valve is to be
placed between the PRV and the heater. No reducing
coupling or other restriction may be installed in the discharge
line. The discharge line must be installed such that it allows
complete drainage of both the PRV and the line. The location
of the PRV must be readily accessible for servicing or
replacement, and be mounted as close to the water heater
as possible. See Fig 7.
C. Use only your hand to push in or turn the gas control
buttons. Never use tools. If a button will not push in, check
to make sure the buttons are being pushed in the proper
sequence. Follow these instructions exactly. If control
button(s) are jammed, close the gas supply and call a
qualified service technician. Attempted forceful repair may
result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the control
system and any gas control which has been under water.
To install the PRV, a suitable fitting connected to an extension
on a “T” fitting can be sweated to the hot water line.
12
6 720 607 030
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHTING INSTRUCTIONS (as seen on front cover
of heater)
GAS CONTROL SLIDE
1. STOP! Read the safety information above on this plate.
2. The Gas valve must be turned off by sliding the gas valve
button to the far left under the OFF ( ) mark.
3. Wait five (5) minutes to clear out any gas. If you smell
gas, STOP! Follow “B” in the safety information above
on this plate. If you don’t smell gas, go to next step.
4. The pilot burner is located behind the peephole in the
front center of the jacket directly below this instruction
plate.
TEMPERATURE
ADJUSTMENT KNOB
Fig. 9 - Water Flow Control Knob
(counterclockwise) will produce a temperature rise of
approximately 45F for flow rates between 1.1 and 3.7 gallons
per minute. When setting the gas control slide to the single
5. Slide the gas valve button to the right, under mark (
).
flame (
) setting and positioning the knob fully clockwise,
6. Fully depress gas valve button and light pilot by pushing
“PILOT IGNITER” button ( ). This step may have to be
repeated.
7. Observe the pilot flame through the peephole. The gas
valve button should be held down at least 15 seconds
with pilot burning. When the gas valve button is released,
the pilot should continue to burn.
the heater will produce a temperature rise of approximately
55F at flow rates between 0.5 and 2.0 gallons per minute.
Turning the dial all the way the counterclockwise will produce
a temperature rise of approximately 33F for flow rates
between 1.1 and 3.7 gallons per minute. It is safest to select
a comfortable temperature and not have to mix in a
considerable amount of cold water. The positions you select
will depend on the temperature of the incoming water (50F
is average in the U.S.). In warm weather regions where the
incoming ground water is generally warmer, or during hot
weather months in other areas, a single flame ( ) setting
may be best. During the colder months, or in cold climate
- If the gas valve button does not pop up when released,
stop and immediately call your service technician or gas
supplier.
- If pilot does not stay lit, repeat steps 1 through 7.
- If pilot will not stay lit after several tries, slide the gas
valve button to the left, under the OFF ( ) mark and call
service technician or gas supplier.
areas, a three flame (
) setting may be best. NOTE: The
knob setting will affect the activation point of the heater;
fully clockwise will allow the heater to activate at 0.5 gal/
minute. Fully counterclockwise will allow the heater to
activate at 1.1 gal/minute.
Do not supply the 125B with preheated water. For this type
of application, use the solar back-up model 125B LPS or
125B NGS.
8. Once pilot remains lit, then release gas valve button. The
heater will now fire when water is drawn at a rate greater
than the threshold flow rate.
NOTE: If main burner should fail to ignite, make sure pilot is
burning. If not, repeat lighting steps 1 through 7.
NOTE: The 125B operates in two modes. See SETTING
THEWATERTEMPERATURE.
If the inlet water temperature to the water heater is very
warm the heater can produce temperatures that may be
found to be too hot. A temperature balance shower valve
can automatically mix in cold water to reduce such hot water
temperature, in the event of any temperature instability with
the use of a temperature balance shower valve, refer to
shower valve manufactures instructions for internal
adjustment setting. Adjustments should be made to the
hottest setting in the shower valve. Additionally the
temperature control of the heater can be adjusted to produce
a more comfortable hot water temperature.
TO TURN OFF GAS TO APPLIANCE
Slide the gas valve button to the far left, under the off (
mark and close the gas supply to the heater.
)
SETTING THE WATER TEMPERATURE
The Aquastar 125B has a gas control that modulates burner
input in response to hot water flow. Its purpose is to ensure
that the hot water temperature will remain steady, although
the water flow demand may vary (down to ½ gal/minute).
Also, depending on the unit’s adjustable gas control slide
MAINTENANCE AND SERVICE
being set in the single flame (
) or three flame (
)
REVIEW MAINTENANCE TABLE ON THE
BACK OF THIS MANUAL
setting, the 125B can produce and control comfortable hot
water temperatures as seasonal ground water temperatures
vary.
To adjust the temperature on the heater, turn on a hot water
tap. At the water heater, turn the temperature adjustment
knob (see Fig. 9) all the way to the right (clockwise) and set
Approximately once a year, the AquaStar should be checked
and cleaned. To remove the front cover, first remove the
incandescent particle tray, then pull off the temperature
adjustment knob and unscrew and remove the plastic collar.
Pull main cover out toward you and lift up and out. THE
FOLLOWING OPERATIONS SHOULD BE PERFORMED
BY A QUALIFIED SERVICE PERSON:
the gas control slide to the three flame (
) setting. This
will produce a temperature rise of approximately 90F at flow
rates between 0.5 and 2.0 gallons per minute. Given that
average incoming water temperatures are 50F in winter
months; this heater will produce approximately 140F water
at these flow rates. Turning the dial all the way to the left
Vent System: Should be checked annually. Clean and repair
as needed.
6 720 607 030
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Valve (Part # 8707002649): The water valve on
this heater should be serviced periodically. Lubricate
component #23 on page 19 with a small amount of silicon,
faucet or lithium grease every two years to keep its o rings
fresh and pushrod sliding smoothly. Every 3-5 years replace
component #23 on page 19. The frequency will depend on
the mineral content of the water and conditions of use or
whenever signs of corrosion appear at the gas and water
valve joint. Periodically check that the water inlet filter (#25
on page 19) is clean as well.
AIR SCREEN
NOTE: If water valve is removed, be sure to also inspect the
o ring seal on the end of the right hand side water pipe
before re-installing. Lubricating the o ring with lithium or
faucet and valve grease is recommended.
PILOT ORIFICE
Fig. 11 - Pilot burner with air screen/ pilot orifice
Pilot Flame: The pilot flame should burn with a clean sharp
blue flame and should resemble the diagram in Fig 10. If the Main Burner Flames: The main burner flames should be
flame is yellow, or if the pilot knob has to remain depressed blue, with a more intense blue cone in the center core. Yellow
for a long time in order to keep the pilot lighted, the pilot flames could be a sign of wrong size gas orifices or dirty
burner and or the pilot burner orifice may need to be cleaned, burners, or a blockage on the heat exchangers fins. If some
the orifice may need to be replaced, and or the air screen burners have yellow flames while others have good flames,
may need cleaning. The pilot flame should envelop it is likely that dust, lint or spider webs have partially clogged
approximately 10 mm (3/8") of the tip of the thermocouple. the burner venturis. To clean the burners, contact a gas
If it is too small, the pilot burner must be cleaned. To obtain service person.
a spark, the position of the Piezo igniter electrode should be
approximately 3 mm (1/8") from the pilot burner tip.
Mineral Scale Build-up: The AquaStar heater, when operated
at lower temperatures settings, does not accumulate mineral
build-up. If however, the heater is used at the higher
temperature settings and the water has a high mineral
content, periodic descaling may be necessary. The heating
coils should be flushed with a descaling solution. Consult
your dealer or Controlled Energy for instructions.
3mm
Correct gap between pilot
burner tip and electrode tip
Consult your service person.
Piezo Electrode
Air screen filter
TROUBLE SHOOTING (see maintenance table)
Introduction
The AquaStar 125B burners are activated by a water flow
valve. Numerous water related problems can cause this water
valve to malfunction such as: Insufficient water flow volume
to activate the burners at its minimum flow requirement;
Dirt in the water flow valve causing it to malfunction;
Sediment build-up in faucet aerators, or shower heads;
Uneven pressures between cold and hot. (with single lever
faucets) Plumbing cross overs. These water flow related
problems can cause the heater to deliver less than its full
output, or to fail to ignite or to shut down completely.
Thermocouple
Piezo
Electrode
Fig. 10 - Characteristic Pilot Flame
Problems are stated in upper case, bold face. Most common
causes for the problems follow in order of likelihood. The
suggested solutions require that the cover be taken off. To
do this, remove incandescent particle tray, pull off the
temperature adjustment knob and unscrew and remove the
plastic collar. Pull main cover out toward you and lift up and
out.
To clean the pilot burner and/ or the pilot orifice : Turn
off the gas at the unit. Remove the cover of the heater. To
do so, pull off the temperature adjustment knob and unscrew
and remove the plastic collar and unscrew the central screw
located at the bottom of the front cover. Pull main cover out
toward you and lift up and out . Pull the air screen off, wash
it and blow any lint off (See Fig 11). The pilot orifices should
also be cleaned or replaced. Do not enlarge the orifice. Do
not use any wire or sharp object to clean orifices. Natural
gas orifices are large enough that you can usually clean
them by blowing through them. LP orifices, on the other
hand, are too small to clean and should be replaced. See
#3 in Trouble Shooting Section.
To access the pilot orifice, remove 2 screws holding pilot
assembly in place. Then loosen compression fittings to expose
pilot orifice.
14
6 720 607 030
Download from Www.Somanuals.com. All Manuals Search And Download.
PILOT LIGHT WILL NOT LIGHT
3. Poor thermocouple connection at the electromagnet
Note: Electromagnet is part #8707201012 located on the
right side of the gas valve behind the piezo push-button
assembly. Check the tightness of the thermocouple
1. No gas to the AquaStar
A. Gas cock on gas line may not be open.
B. Gas valve button has not been moved to single flame connection nut at the electromagnet: The Electro-magnet
position (
). Slide button to right to PILOT.
connection is a large aluminum 17mm hex head nut. The
thermocouple end is a 5 mm brass nut which screws into
the 17 mm nut. Tighten the thermocouple nut snugly but not
too tight.
C. Gas regulator may be shut or damaged.
2. In-line AquaStar gas regulator jammed (usually on
LP gas)
Replace or unlock the regulator. Note: The regulator 4. Poor circuit connections at the ECO (overheat sensor)
furnished with the heater is designed for low gas pressure. or the flue gas safety device
Excessive pressure will lock it up (propane only). Locking Oxidation or looseness of the terminal connections can result
usually happens if the gas pressure between the gas tank in millivolt current loss through the thermocouple safety
(propane) and the water heater’s gas regulator has not been circuit. Clean terminals with very fine sand paper or an eraser
reduced. See page 2 for recommended correct gas pressure. and reconnect leads.
To unlock a regulator, consult your gas supplier.
5. Faulty ECO (part #8707206074)
If cleaning the terminals attached to the ECO did not fix the
problem, connect a jumper wire between the two wires and
3. Pilot orifice clogged and/or air screen dirty, or pilot
gas filter is dirty.
Clogging of the pilot burner can be caused by dust and any try to relight the pilot. If the pilot flame now remains on,
suspended matter contained in the ambient air. replace the ECO. If the flame still goes out when the button
As a result, the pilot flame is weakened and thus can no is released, the ECO is not defective. Go to next step.
longer heat the thermocouple sufficiently. For cleaning
purposes, the air filter screen is pulled off, washed and blown 6. Faulty thermocouple (part #8707206074) or
out. The pilot orifice has likewise to be cleaned or exchanged.
electromagnet ) Unless these 2 parts are at least 8 to
10 years old, it is very unlikely that they are faulty.
Before testing, reconfirm that #2 is absolutely correct,
and that all connections are clean and tight.
4. Air in the Gas Line
Note: Normally this is a problem only at the time of initial
installation, after the pipes have been worked on, or after a To test the thermocouple, disconnect the thermocouple lead
propane tank has been allowed to empty, or after the heater at the ECO. Insert a multi-meter probe into the thermocouple
has been shut down for a long time.
lead and attach or hold the other lead at the metal gas
Bleed all the air trapped in the gas line. Because of the very valve (DC common). Light the pilot flame and hold button,
small pilot orifice (especially on LP gas models), bleeding meter reading should be 24 mVDC or more. If the reading is
out all the air could take several minutes. Slide the gas 24 mVDC or more the thermocouple is good. To test the
valve button to single flame position (
) and depress this electromagnet, re-connect the thermocouple lead to the
button until all the air has escaped, and the gas has arrived. ECO, light pilot and hold button while taking a reading
During this process, press repeatedly on the piezo ignition between the ECO and flue gas sensor leads and the metal
button until the pilot flame has ignited.
gas valve (DC common). The reading should drop to 19
mVDC or less. If it does not, replace the electromagnet.
PILOT LIGHTS BUT FLAME GOES OUT WHEN BUTTON
IS RELEASED
BURNERSDO NOTIGNITE WHEN HOTWATERIS TURNED
ON
1. Pilot push button was not pushed in far enough or
was not held in long enough
Once pilot flame has been lighted. Hold button pushed in
for at least 15 seconds to give time for the pilot flame to
properly heat the tip of the thermocouple.
1. Pilot is not on.
Light the pilot. See lighting instructions.
2. Cold incoming water connection made to wrong side
of heater
Make sure cold water inlet connection is on the right side of
heater when you are facing heater.
2. Pilot flame improperly aimed or is too weak so it is
not properly heating the tip of the thermocouple.
The Pilot flame should be a sharp blue flame and aimed at
the tip of the thermocouple so that it envelops 10 mm(3/8")
of the thermocouple tip. Pilot flame has to be properly aimed
at the thermocouple. See Fig 10.
3. Water flow rate at hot water tap is too low.
Note: When the flow control knob is turned all the way
clockwise, the AquaStar models 125B require 1/2 gallon
per minute flow to activate the burners. This is a flow which
would fill a quart jar in 30 seconds. If the flow control knob
is turned fully counterclockwise, a flow rate of 1.1 gpm is
required to activate the burners.
4. Cold water inlet filter on heater is dirty.
Remove filter and clean. This screen filter is located at the
inlet side of the water valve (fig. 13, #25). Check and clean
faucet aerators too.
6 720 607 030
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Crossover in household plumbing
WATER IS TOO HOT
The AquaStar burner activates when there is sufficient water
pressure drop in the AquaStar water valve assembly — i.e.
when a hot water faucet is opened. If there is a crossover in
the plumbing, the necessary pressure drop in the AquaStar
will be insufficient, or totally eliminated. A plumbing crossover
can be caused by a bad washer at a single lever faucet or
incorrect plumbing or a mixing valve in the line, etc. which
permits hot and cold water to mix in the plumbing. The
crossover will create a back pressure in the system preventing
the pressure drop in the Aquastar — i.e. cold water is entering
the water heater from both sides and the burners will not
come on. To confirm there is no crossover in the plumbing,
shut off the cold water supply to the AquaStar. Open your
hot water taps. There should not be any water flowing. If
there is water flowing, there is a crossover in the plumbing.
This is a plumbing problem, not an Aquastar problem. Please
contact your plumber.
1. Temperature Selection too high
Position the gas control slide to the single flame (
setting to reduce the burner output and/or turn the
temperature adjustment knob counterclockwise to lower the
maximum water temperature. Note: turning the knob
counterclockwise will increase the activation flow rate.
)
2. Inlet water temperature is very warm
Increased seasonal ground water temperatures will affect
the hot water output temperature. Reduce the burner output
if the inlet water is very warm (60-75F) by positioning the
gas control slide to the single flame (
) setting. The
temperature adjustment knob setting may also be lowered if
necessary, reference SETTING THE WATER
TEMPERATURE section.
WATER IS NOT HOTENOUGH
6. Water valve parts may be dirty or components
damaged.
1. Temperature selection too low.
Change the setting. Turn the temperature adjustment knob
clockwise and/or slide the gas control to the winter mode
setting for increased burner output.
Water valve and component parts must be totally free of
dirt. First check that the venturi is free of dirt particles. In
hard water areas, mineral deposits can eventually (3 to 5
years in hard water areas) corrode the water valve parts to
a point where they will need replacing. Any sign of moisture
or corrosion at the joint of the water valve and the gas valve
is a sign that the water valve assembly components need to
be serviced immediately. Note: Water valve for model 125B
is part# 8707002649 for both LP and NG models. (Contact
service person to clean water valve or replace if corrosion
is present).
Note: This will decrease the activation flow rate.
2. Btu input is too low due to insufficient gas pressure
It is extremely important for a tankless instantaneous
water heater to have the right size gas line to obtain
the correct gas pressure
See specifications on page 2. Unlike storage tank water
heaters, the burners of a tankless water heater must be very
powerful to heat water instantaneously since they do this
only at the time hot water is actually being used. It is therefore
imperative that the gas pressure requirement be met exactly.
Insufficient gas pressure will directly affect the water
temperature at the time of usage. See page 2 for correct
PILOT LIGHT GOES OUT DURING OR IMMEDIATELY
AFTER HOT WATER HAS BEEN USED
1. Gas pressure too low
Very low gas pressure may be caused by low delivered gas gas pressure settings and page 10 for locations where gas
pressure, a jammed gas regulator or undersized gas lines. If pressures are taken.
the gas lines are undersized, there may still be the specified
3. Btu input is too low due to insufficient gas supply
Make sure your main gas line is fully opened. If using LP
gas, be sure that the size of the propane tank is adequate to
supply the required gas pressure.
static gas line pressure. However when the water valve opens,
and gas enters the burners, the pressure could drop sharply,
causing the pilot flame to go out. Have a gas technician
confirm the gas pressure both static and at maximum Btu
output. Specifications for your heater are on page 2.
4. Cold water is mixing with the hot water between the
AquaStar and the outlet
Compare water temperature at outlet of the AquaStar (hold
the AquaStar’s outlet pipe with your hand) and at the tap. If
2. Pilot may be dirty or weak
See Page 14 for instructions on pilot maintenance.
3. Burners are not shutting down immediately when hot these two are very different, check for mixing valve or
water is turned off plumbing crossover (see “MAIN BURNERS WILL NOT
Note: If burners don’t shut down immediately when the hot IGNITE...” paragraph #6). Where automatic “anti-scald”
water is turned off, the heater will overheat and the ECO valves are required by code, lower the temperature setting
will shut-off the gas. Rebuild the water valve assembly. on the AquaStar as much as possible and balance the
Contact service person to clean or rebuild water valve.
pressure between cold and hot water after the AquaStar.
4. ECO (overheat sensor) tripped due to overheating
Re-ignite the appliance 10 minutes later. If it happens again,
contact your service person.
5. Parts in water valve are dirty or damaged, which will
prevent the gas valve from being fully opened.
Water valve maintenance needs to be performed, see #7
under BURNERS DO NOT IGNITE WHEN HOT WATER
IS TURNED ON.
5. Flue gas safety device tripped
Ventilate the room and re-ignite the appliance 10 minutes
later. If it happens again, contact your service person.
16
6 720 607 030
Download from Www.Somanuals.com. All Manuals Search And Download.
HOT WATER TEMPERATURE FLUCTUATES / UNIT
DEACTIVATED
1. Unbalanced pressure in waterlines
The added restriction caused by the Aquastar in the hot
water system can result in uneven pressures between the
cold and the hot. In such cases when mixing cold water at
the tap, the lower hot water pressure may be overpowered
by the higher cold water pressure in the building, which may
cause the Aquastar burners to shut down (deactivate).
Do not add any flow restrictor to the shower head.
Position the gas control slide to the single flame (
)
setting to reduce the burner output and/or turn the
temperature adjustment knob counterclockwise to lower the
maximum water temperature.
Note: turning the knob counterclockwise will increase
the activation flow rate.
2. Temperature balance valves
If the inlet water temperature to the water heater is very
warm the heater can produce temperatures that may be
found to be too hot. A temperature balance shower valve
can automatically mix in cold water to reduce such hot water
temperature, in the event of any temperature instability with
the use of a temperature balance shower valve, refer to
shower valve manufactures instructions for internal
adjustment setting. Adjustments should be made to the
hottest setting in the shower valve. Additionally the
temperature control of the heater can be adjusted to produce
a more comfortable hot water temperature. See SETTING
THE WATER TEMPERATURE section.
3. Cold water is mixing with the hot water between the
AquaStar and the outlet
See #6 under “Burners do Not Ignite When Hot Water Is
Turned On”.
4. Inlet water pressure is erratic due to inadequate supply
water pressure or saturated pressure tank on well
system
For installation on a private well system with the use of a
pressure tank, the lowest pressure range setting
recommended is 30-50 psi (2.07-3.45 bar).
5. Gas pressure is too low
See page 2 and 10 for correct specifications.
6 720 607 030
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
6 720 607 030
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 12 - Diagram of AquaStar 125 B
1
4
3
2
5
6
7
8
9
10
11
13
12
6720606800-07.1AL
1. Heat exchanger
2. Pilot assembly
3. Burner manifold gas
pressure test nipple
4. Main gas burner
5. Pilot gas tubing
6. Gas valve
8. Gas control slide
9. Piezo igniter
10. Water valve
11.
Temperature adjustment
selector
12. Gas inlet gas pressure test
nipple
7.
Pressure tap screw
location
13. Flexible hot outlet
6 720 607 030
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 13 - INTERIOR COMPONENTS DIAGRAM AND PARTS LIST
20
6 720 607 030
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 13
INTERIOR COMPONENTS DIAGRAM
AND PARTS LIST 125B
1
2
3
4
5
6
7
8
9
Cover
8 705 421 025
Temperature adjustment knob
Temperature adjustment collar
Draft diverter
Heat exchanger
Outlet flex hose
Washer
Cold water pipe
Main burner
Main burner
Pilot burner
Pilot air screen
Piezo electrode
Pilot injector
Pilot injector
Pilot tube
Burner assembly washer
Throttle disc
Gas valve
Gas valve
Gas supply pipe
Electromagnet
Thermocouple / Flue Gas Sensor
Water valve
Water valve cover
Pushrod
Diaphragm
8 702 000 111
8 700 403 008
8 705 505 354
8 705 406 235
8 700 703 130
8 700 103 658
8 700 705 627
8 708 120 298 NG
8 708 120 296 LP
8 718 105 051
8 700 507 055
8 708 107 002
8 708 200 005 NG
8 748 200 173 LP
8 700 707 320
8 710 103 060
8 700 100 174 LP
8 707 021 090 NG
8 707 021 091 LP
8 700 705 552
8 707 201 012
8 707 206 074
8 707 002 649
8 705 500 101
8 700 306 114
8 700 503 053
8 700 507 001
8 710 103 043
8 708 500 289
8 705 705 009
8 708 205 279
8 700 703 114
8 707 206 040
8 700 715 178
8 710 103 045
8 703 401 051
9
10
11
12
13
13
14
15
16
17
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
34
35
Water inlet filter
Water connection gasket
Water valve selector screw
Volumetric water governor
Venturi
Water elbow fitting
Overheat sensor (ECO)
Connecting pipe hot
Washer
Water valve set screw
6 720 607 030
21
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Aquastar
General
Service labor costs
Aquastar water heaters are warranted by the Manufacturer This warranty does not cover any labor costs associated
(BOSCH) through Controlled Energy Corp. Controlled with service, removal or re-installation of part(s). All such
Energy Corp. (CEC) will furnish a replacement heat costs must be borne by the Purchaser. Additionally, this
exchanger and will furnish a replacement of any other part warranty does not cover any labor costs associated with
which fails in normal use and service within the applicable service, removal or re-installation of the original water heater
periods specified below, in accordance with the terms of or a replaced water heater.
this warranty. The CEC replacement will be warranted for
the unexpired portion of the original warranty. This warranty How to Make a Claim
will be valid only for water heaters in possession of the original Any claim for warranty parts should be made to your local
purchaser as recorded on the warranty card.
dealer, distributor or to CEC. If CEC, please contact the
Technical Support Department:
The heat exchanger
When the unit is professionally installed: If the heat
exchanger fails within fifteen (15) years after the original
installation and operation CEC will furnish a replacement
heat exchanger. However, if the water heater is installed in
other than a single family dwelling this heat exchanger
warranty is limited to two (2) years from date of original
installation and operation.
Controlled Energy Corp.
340 Mad River Park
Waitsfield, VT 05673
Phone: 800-642-3111
In most cases, the dealer or distributor will be able to promptly
* The 15 year warranty period on the heat exchanger is honor your claim and subsequently notify CEC. However,
reduced to ten (10) years if the unit is not installed by a all replacements are made subject to validation by CEC of
plumber or licensed gas fitter.
in-warranty coverage. The damaged or defective item must
be made available in exchange for the replacement.
Exceptions
This warranty will not apply:
Miscellaneous
1. to defects or malfunctions resulting from failure to properly No one is authorized to make any other warranties on behalf
install, operate or maintain the unit in accordance with of CEC. It is expressly understood that the replacement
the printed instructions provided;
2. to damage or abuse, accident, neglect or freezing and warranties, express or implied, including warranties of
other acts of nature; merchantability or fitness for a particular use or purpose,
3. to damage resulting from operation with either the flame and further that CEC shall not be liable for any loss or
sensor rod or overheat sensor removed; damage directly or indirectly arising from the use of the hot
warranty of CEC shall be in lieu of any and all other
4. to failure of the heat exchanger resulting from the water heater, or for any consequential damages arising from
operation of the water heater in a corrosive atmosphere such use (including damages from water leakage). CEC’s
or at water temperatures exceeding the maximum rating, sole liability with respect to any defect shall be for the
or if the water heater is not supplied with potable water; replacement of the defective part(s). Some states do not
5. to defects or damage cause by any attachment allow such limitations and exclusions, so the above may not
or modification, including any energy-saving device.
apply to you.
This warranty gives specific legal rights. You may also have
other rights which vary from state to state.
All other parts
If any other part fails within two (2) years after original
installation and operation, CEC will furnish a replacement
part free of charge.
Shipping costs
In addition to supplying the replacement part(s), CEC will
provide ground service delivery for these parts. Expedited or
upgraded shipping will be charged to the customer.
06.03
22
6 720 607 030
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 14 - Flow chart of Aquastar 125 B
6 720 607 030
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE TABLE see pages 13 & 14
EVERY YEAR
EVERY 2 YEARS EVERY 3-5 YEARS
LUBRICATE WATER VALVE
REBUILD WATER VALVE
†
†
INSPECT WATER FILTER SCREEN
INSPECT PILOT ASSEMBLY
INSPECT VENT ASSEMBLY
INSPECT MAIN BURNER
†
†
†
†
Replacement Parts available from North American
Distributor
CONTROLLED ENERGY CORP.
340 Mad River Park
VULCANO Termodomésticos S.A.
Estrada de Cacia
3801 - 856 Aveiro - PORTUGAL
Waitsfield, Vermont 05673
Phone 800-642-3111
Fax (802) 496-6924
© 2003 Controlled Energy Corporation, Waitsfield,
VT all rights reserved
Recycled paper
Download from Www.Somanuals.com. All Manuals Search And Download.
|