Bosch Appliances Security Camera VG5 800 SERIES User Manual
AutoDome 800 Series HD PTZ Camera  
VG5 800 Series  
en Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Table of Contents | en  
3
Table of Contents  
1
Safety  
7
7
1.1  
1.2  
1.3  
1.4  
Important Safety Instructions  
Safety Precautions  
9
Important Notices  
9
Customer Support and Service  
13  
2
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
Unpacking  
14  
14  
14  
15  
15  
15  
16  
17  
19  
20  
22  
23  
26  
27  
27  
31  
2.1  
2.1.1  
2.1.2  
2.1.3  
2.2  
Parts List  
Description  
Tools Required  
Pre-installation Checklist  
2.3  
Mount Power Supply Box  
2.4  
Route Wires and Attach Connectors  
Power Supply Box Connections  
Route Power through Intermediate Power Supply Box  
Attach Pendant Arm to Power Supply Box  
Make Connections in Power Supply Box  
Installing the VG4-A-ARMPLATE  
Attach the Pendant Arm to the Mounting Plate  
Route and Connect Wires to a Power Supply Box  
Attach Pendant to Arm and Tighten  
2.4.1  
2.5  
2.6  
2.7  
2.8  
2.8.1  
2.8.2  
2.9  
3
Installing Roof Parapet and Pipe Mounts  
Unpacking  
33  
33  
33  
33  
33  
34  
34  
36  
37  
39  
39  
41  
42  
45  
46  
47  
49  
3.1  
3.1.1  
3.1.2  
3.1.3  
3.2  
Parts List  
Description  
Tools Required  
Pre-installation Check List  
Mount Power Supply Box  
3.3  
3.3.1  
3.4  
Attach Cover Door  
Route Wires and Attach Connectors  
Wiring the Power Supply Box  
Wiring the Fiber Optic Model  
Power Supply Box Connections  
Installing the VG4-A-9230 Roof Parapet Mount  
Installing the VG4-A-9543 Pipe Mount  
Wire the Pipe Interface Board  
Connecting Wires to the Pipe Interface Board  
Attach Pendant to Pipe and Tighten  
3.4.1  
3.4.2  
3.4.3  
3.5  
3.6  
3.7  
3.7.1  
3.8  
4
Cable and Wire Standards  
Power  
51  
51  
51  
51  
52  
4.1  
4.2  
4.3  
4.4  
Wire Distance Guide for Pendant  
Video and Control Cables  
Audio Cables  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
en | Table of Contents  
AutoDome 800 Series HD PTZ Camera  
5
Alarms and Relay Connections  
54  
54  
54  
54  
54  
55  
5.1  
5.2  
Alarm Inputs  
Connecting Alarms (inputs 1 or 2)  
Connecting a Normally Open Alarm  
Connecting a Normally Closed Alarm  
Configuring an Open Collector Output  
5.2.1  
5.2.2  
5.3  
6
Using the AutoDome 800 Series  
Overview of Features  
56  
56  
56  
57  
58  
59  
60  
60  
61  
61  
64  
65  
65  
66  
66  
66  
68  
68  
6.1  
6.2  
System Requirements  
6.3  
Connecting the AutoDome 800 Series to the PC  
Configuring the AutoDome 800 Series Camera  
Changing the Network Settings  
Configuring Intelligent Tracking  
Intelligent Tracking Operation  
Guidelines for Implementing Intelligent Tracking  
The Livepage  
6.4  
6.4.1  
6.5  
6.5.1  
6.5.2  
6.6  
6.6.1  
6.6.2  
6.6.3  
6.7  
Entering a Keyboard Control Command  
Using Intelligent Tracking  
Using Special Functions  
Saving Snapshots  
6.8  
Recording Video Sequences  
Processor Load  
6.9  
6.10  
6.10.1  
Recordings page  
Controlling playback  
7
Configuring the AutoDome 800 Series  
Basic Mode: Device Access  
Basic Mode: Date/Time  
Basic Mode: Network  
Basic Mode: Encoder  
Basic Mode: Audio  
Basic Mode: Recording  
Basic Mode: System Overview  
Advanced Mode: General  
Identification  
70  
70  
71  
72  
72  
73  
73  
74  
74  
74  
74  
75  
76  
77  
77  
78  
79  
79  
79  
80  
82  
84  
84  
7.1  
7.2  
7.3  
7.4  
7.5  
7.6  
7.7  
7.8  
7.9  
7.10  
7.11  
7.12  
7.13  
7.14  
7.15  
7.16  
7.17  
7.18  
7.19  
7.20  
7.21  
7.22  
Password  
Date/Time  
Display Stamping  
Advanced Mode: Web Interface  
Appearance  
Livepage Functions  
Logging  
Advanced Mode: Camera  
Installer Menu  
Encoder Profile  
Encoder Streams  
Privacy Masks  
Camera Settings  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
AutoDome 800 Series HD PTZ Camera  
Table of Contents | en  
5
7.23  
7.24  
7.25  
7.26  
7.27  
7.28  
7.29  
7.30  
7.31  
7.32  
7.33  
7.34  
7.35  
7.36  
7.37  
7.38  
7.39  
7.40  
7.41  
7.42  
7.43  
7.44  
7.45  
7.46  
7.47  
7.48  
7.49  
7.49.1  
7.49.2  
7.49.3  
7.50  
7.51  
7.52  
7.53  
7.54  
7.55  
7.56  
7.57  
7.58  
Lens Settings  
PTZ Settings  
86  
87  
Diagnostics  
88  
Preposition and Tours  
Sectors  
89  
89  
Miscellaneous  
Logs  
90  
90  
Audio  
90  
Pixel Counter  
Advanced Mode: Recording  
Storage Management  
Recording Profiles  
Retention Time  
Recording Schedule  
Recording Status  
Advanced Mode: Alarm  
Alarm Connections  
VCA  
90  
91  
91  
92  
94  
94  
95  
95  
95  
97  
Audio Alarm  
101  
102  
103  
103  
104  
104  
104  
105  
105  
105  
106  
106  
108  
109  
110  
111  
111  
111  
111  
112  
112  
Alarm E-Mail  
Alarm Task Editor  
Alarm Rules  
Advanced Mode: Interfaces  
Alarm Inputs  
Relay  
Advanced Mode: Network  
Network Access  
IPv4  
IPv6  
Detailed Settings  
Advanced  
Multicast  
FTP Posting  
IPv4 Filter  
Encryption  
Advanced Mode: Service  
Maintenance  
Licenses  
System Overview  
8
Bubble Handling and Cleaning  
Handling  
113  
113  
113  
113  
114  
8.1  
8.2  
Cleaning  
8.2.1  
8.2.2  
Cleaning the Bubble Interior  
Cleaning the Bubble Exterior  
9
BVIP Firmware Updates  
115  
115  
115  
9.1  
9.2  
Upgrading the AutoDome 800 Series  
Beginning the Firmware Update Process  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
en | Table of Contents  
AutoDome 800 Series HD PTZ Camera  
A
Keyboard Commands by Number  
116  
117  
Index  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
AutoDome 800 Series HD PTZ Camera  
Safety | en  
7
1
Safety  
1.1  
Important Safety Instructions  
Read, follow, and retain for future reference all of the following safety instructions. Heed all  
warnings on the unit and in the operating instructions before operating the unit.  
1. Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions  
provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist  
fluff-free cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol  
cleaners.  
2. Heat Sources - Do not install the unit near any heat sources such as radiators, heaters,  
stoves, or other equipment (including amplifiers) that produce heat.  
3. Ventilation - Any openings in the unit enclosure are provided for ventilation to prevent  
overheating and ensure reliable operation. Do not block or cover these openings. Do not  
place the unit in an enclosure unless proper ventilation is provided, or the manufacturer's  
instructions have been adhered to.  
4. Water - Do not use this unit near water, for example near a bathtub, washbowl, sink,  
laundry basket, in a damp or wet basement, near a swimming pool, in an outdoor  
installation, or in any area classified as a wet location. To reduce the risk of fire or  
electrical shock, do not expose this unit to rain or moisture.  
5. Object and liquid entry - Never push objects of any kind into this unit through openings  
as they may touch dangerous voltage points or short-out parts that could result in a fire  
or electrical shock. Never spill liquid of any kind on the unit. Do not place objects filled  
with liquids, such as vases or cups, on the unit.  
6. Lightning - For added protection during a lightning storm, or when leaving this unit  
unattended and unused for long periods, unplug the unit from the wall outlet and  
disconnect the cable system. This will prevent damage to the unit from lightning and  
power line surges.  
7. Controls adjustment - Adjust only those controls specified in the operating instructions.  
Improper adjustment of other controls may cause damage to the unit. Use of controls or  
adjustments, or performance of procedures other than those specified, may result in  
hazardous radiation exposure.  
8. Overloading - Do not overload outlets and extension cords. This can cause fire or  
electrical shock.  
9. Power cord and plug protection - Protect the plug and power cord from foot traffic,  
being pinched by items placed upon or against them at electrical outlets, and its exit  
from the unit. For units intended to operate with 230 VAC, 50 Hz, the input and output  
power cord must comply with the latest versions of IEC Publication 227 or IEC Publication  
245.  
10. Power disconnect - Units with or without ON/OFF switches have power supplied to the  
unit whenever the power cord is inserted into the power source; however, the unit is  
operational only when the ON/OFF switch is in the ON position. The power cord is the  
main power disconnect device for switching off the voltage for all units.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
en | Safety  
AutoDome 800 Series HD PTZ Camera  
11. Power sources - Operate the unit only from the type of power source indicated on the  
label. Before proceeding, be sure to disconnect the power from the cable to be installed  
into the unit.  
–
–
For battery powered units, refer to the operating instructions.  
For external power supplied units, use only the recommended or approved power  
supplies.  
–
–
For limited power source units, this power source must comply with EN60950.  
Substitutions may damage the unit or cause fire or shock.  
For 24 VAC units, voltage applied to the unit's power input should not exceed 10%,  
or 28 VAC. User-supplied wiring must comply with local electrical codes (Class 2  
power levels). Do not ground the supply at the terminals or at the unit's power  
supply terminals.  
–
If unsure of the type of power supply to use, contact your dealer or local power  
company.  
12. Servicing - Do not attempt to service this unit yourself. Opening or removing covers may  
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service  
personnel.  
13. Damage requiring service - Unplug the unit from the main AC power source and refer  
servicing to qualified service personnel when any damage to the equipment has  
occurred, such as:  
–
–
–
–
–
–
–
the power supply cord or plug is damaged;  
exposure to moisture, water, and/or inclement weather (rain, snow, etc.);  
liquid has been spilled in or on the equipment;  
an object has fallen into the unit;  
unit has been dropped or the unit cabinet is damaged;  
unit exhibits a distinct change in performance;  
unit does not operate normally when the user correctly follows the operating  
instructions.  
14. Replacement parts - Be sure the service technician uses replacement parts specified by  
the manufacturer, or that have the same characteristics as the original parts.  
Unauthorized substitutions may cause fire, electrical shock, or other hazards.  
15. Safety check - Safety checks should be performed upon completion of service or repairs  
to the unit to ensure proper operating condition.  
16. Installation - Install in accordance with the manufacturer's instructions and in  
accordance with applicable local codes.  
17. Attachments, changes or modifications - Only use attachments/accessories specified by  
the manufacturer. Any change or modification of the equipment, not expressly approved  
by Bosch, could void the warranty or, in the case of an authorization agreement, authority  
to operate the equipment.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Safety | en  
9
1.2  
Safety Precautions  
DANGER!  
This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside  
the product. If not avoided, this will result in an electrical shock, serious bodily injury, or  
death.  
WARNING!  
Indicates a potentially hazardous situation. If not avoided, this could result in serious bodily  
injury or death.  
CAUTION!  
Indicates a potentially hazardous situation. If not avoided, this may result in minor or  
moderate injury. Alerts the user to important instructions accompanying the unit.  
CAUTION!  
Indicates a potentially hazardous situation. If not avoided, this may result in property damage  
or risk of damage to the unit.  
NOTICE!  
This symbol indicates information or a company policy that relates directly or indirectly to the  
safety of personnel or protection of property.  
1.3  
Important Notices  
Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit  
may fall, causing serious injury and/or serious damage to the unit. Use only with the cart,  
stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use  
caution and care when moving the cart/apparatus combination to avoid injury from tip-over.  
Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination to  
overturn. Mount the unit per the manufacturer's instructions.  
All-pole power switch - Incorporate an all-pole power switch, with a contact separation of at  
least 3 mm in each pole, into the electrical installation of the building.If it is needed to open  
the housing for servicing and/or other activities, use this all-pole switch as the main  
disconnect device for switching off the voltage to the unit.  
Camera grounding - For mounting the camera in potentially damp environments, ensure to  
ground the system using the ground connection of the power supply connector (see section:  
Connecting external power supply).  
Camera lens - An assembled camera lens in the outdoor housing must comply and be tested  
in accordance with UL/IEC60950. Any output or signal lines from the camera must be SELV or  
Limited Power Source. For safety reasons the environmental specification of the camera lens  
assembly must be within the environmental specification of -10 °C (14 °F) to 50 °C (122 °F).  
Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140  
feet, in accordance with NEC800 (CEC Section 60).  
Coax grounding:  
–
–
Ground the cable system if connecting an outside cable system to the unit.  
Connect outdoor equipment to the unit's inputs only after this unit has had its grounding  
plug connected to a grounded outlet or its ground terminal is properly connected to a  
ground source.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10 en | Safety  
AutoDome 800 Series HD PTZ Camera  
–
–
Disconnect the unit's input connectors from outdoor equipment before disconnecting  
the grounding plug or grounding terminal.  
Follow proper safety precautions such as grounding for any outdoor device connected to  
this unit.  
U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides  
information regarding proper grounding of the mount and supporting structure, grounding of  
the coax to a discharge unit, size of grounding conductors, location of discharge unit,  
connection to grounding electrodes, and requirements for the grounding electrode.  
NOTICE!  
This device is intended for use in public areas only.  
U.S. federal law strictly prohibits surreptitious recording of oral communications.  
Your Bosch product was developed and manufactured with high-quality material and  
components that can be recycled and reused. This symbol means that electronic and  
electrical appliances, which have reached the end of their working life, must be collected and  
disposed of separately from household waste material. Separate collecting systems are  
usually in place for disused electronic and electrical products. Please dispose of these units at  
an environmentally compatible recycling facility, per European Directive 2002/96/EC.  
Environmental statement - Bosch has a strong commitment towards the environment. This  
unit has been designed to respect the environment as much as possible.  
Electrostatic-sensitive device - Use proper CMOS/MOS-FET handling precautions to avoid  
electrostatic discharge.  
NOTE: Wear required grounded wrist straps and observe proper ESD safety precautions when  
handling the electrostatic-sensitive printed circuit boards.  
Fuse rating - For security protection of the device, the branch circuit protection must be  
secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC  
Section 60).  
Grounding and polarization - This unit may be equipped with a polarized alternating current  
line plug (a plug with one blade wider than the other blade). This safety feature allows the  
plug to fit into the power outlet in only one way. If unable to insert the plug fully into the  
outlet, contact a locally certified electrician to replace the obsolete outlet. Do not defeat the  
safety purpose of the polarized plug.  
Alternately, this unit may be equipped with a 3-pole grounding plug (a plug with a third pin for  
earth grounding). This safety feature allows the plug to fit into a grounded power outlet only.  
If unable to insert the plug into the outlet, contact a locally certified electrician to replace the  
obsolete outlet. Do not defeat the safety purpose of the grounding plug.  
Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive  
force or shock may damage the unit and the hard disk drives.  
Outdoor signals - The installation for outdoor signals, especially regarding clearance from  
power and lightning conductors and transient protection, must be in accordance with NEC725  
and NEC800 (CEC Rule 16-224 and CEC Section 60).  
Permanently connected equipment - Incorporate a readily accessible disconnect device in  
the building installation wiring.  
Pluggable equipment - Install the socket outlet near the equipment so it is easily accessible.  
PoE - Never supply power via the Ethernet connection (PoE) when power is already supplied  
via the power connector.  
Power disconnect - Units have power supplied whenever the power cord is inserted into the  
power source. The power cord is the main power disconnect for all units.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Safety | en  
11  
Power lines - Do not locate the camera near overhead power lines, power circuits, or  
electrical lights, nor where it may contact such power lines, circuits, or lights.  
SELV  
All the input/output ports are Safety Extra Low Voltage (SELV) circuits. SELV circuits should  
only be connected to other SELV circuits.  
Because the ISDN circuits are treated like telephone-network voltage, avoid connecting the  
SELV circuit to the Telephone Network Voltage (TNV) circuits.  
Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security  
Systems cannot be held liable for any damage that results from missing video information. To  
minimize the risk of lost digital information, Bosch Security Systems recommends multiple,  
redundant recording systems, and a procedure to back up all analog and digital information.  
NOTICE!  
This is a class A product. In a domestic environment this product may cause radio  
interference, in which case the user may be required to take adequate measures.  
FCC & ICES INFORMATION  
(U.S.A. and Canadian Models Only, CLASS A)  
This device complies with part 15 of the FCC Rules. Operation is subject to the following  
conditions:  
–
–
this device may not cause harmful interference, and  
this device must accept any interference received, including interference that may cause  
undesired operation.  
Note  
This equipment has been tested and found to comply with the limits for a Class A digital  
device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits  
are designed to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment. This equipment generates, uses, and  
radiates radio frequency energy and, if not installed and used in accordance with the  
instruction manual, may cause harmful interference to radio communications. Operation of  
this equipment in a residential area is likely to cause harmful interference, in which case the  
user will be required to correct the interference at his expense.  
Intentional or unintentional modifications, not expressly approved by the party responsible  
for compliance, shall not be made. Any such modifications could void the user's authority to  
operate the equipment. If necessary, the user should consult the dealer or an experienced  
radio/television technician for corrective action.  
The user may find the following booklet, prepared by the Federal Communications  
Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This  
booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock  
No. 004-000-00345-4.  
INFORMATIONS FCC ET ICES (commercial applications)  
(modèles utilisés aux États-Unis et au Canada uniquement, CLASSE A)  
Ce produit est conforme aux normes FCC partie 15. la mise en service est soumises aux deux  
conditions suivantes:  
–
–
cet appareil ne peut pas provoquer d'interférence nuisible et  
cet appareil doit pouvoir tolérer toutes les interférences auxquelles il est soumit, y  
compris les interférences qui pourraient influer sur son bon fonctionnement.  
AVERTISSEMENT: Suite à différents tests, cet appareil s’est révélé conforme aux exigences  
imposées aux appareils numériques de Classe A en vertu de la section 15 du règlement de la  
Commission fédérale des communications des États-Unis (FCC). Ces contraintes sont  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12 en | Safety  
AutoDome 800 Series HD PTZ Camera  
destinées à fournir une protection raisonnable contre les interférences nuisibles quand  
l'appareil est utilisé dans une installation commerciale. Cette appareil génère, utilise et émet  
de l'energie de fréquence radio, et peut, en cas d'installation ou d'utilisation non conforme  
aux instructions, générer des interférences nuisibles aux communications radio. L’utilisation  
de ce produit dans une zone résidentielle peut provoquer des interférences nuisibles. Le cas  
échéant, l’utilisateur devra remédier à ces interférences à ses propres frais.  
Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision,  
qui procédera à une opération corrective. La brochure suivante, publiée par la Commission  
fédérale des communications (FCC), peut s’avérer utile : « How to Identify and Resolve Radio-  
TV Interference Problems » (Comment identifier et résoudre les problèmes d’interférences de  
radio et de télévision). Cette brochure est disponible auprès du U.S. Government Printing  
Office, Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4.  
AVERTISSEMENT: Ce produit est un appareil de Classe A. Son utilisation dans une zone  
résidentielle risque de provoquer des interférences. Le cas échéant, l’utilisateur devra  
prendre les mesures nécessaires pour y remédier.  
Disclaimer  
Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the  
security or signaling aspects of this product. UL has only tested fire, shock and/or casualty  
hazards as outlined in UL's Standard(s) for Safety for Information Technology Equipment, UL  
60950-1. UL Certification does not cover the performance or reliability of the security or  
signaling aspects of this product.  
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER  
REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING-  
RELATED FUNCTIONS OF THIS PRODUCT.  
Copyright  
This user guide is the intellectual property of Bosch Security Systems, Inc. and is protected by  
copyright.  
All rights reserved.  
Trademarks  
All hardware and software product names used in this document are likely to be registered  
trademarks and must be treated accordingly.  
NOTICE!  
This user guide has been compiled with great care and the information it contains has been  
thoroughly verified. The text was complete and correct at the time of printing. The ongoing  
development of the products may mean that the content of the user guide can change without  
notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly  
from faults, incompleteness or discrepancies between the user guide and the product  
described.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Safety | en  
13  
1.4  
Customer Support and Service  
If this unit needs service, contact the nearest Bosch Security Systems Service Center for  
authorization to return and shipping instructions.  
Service Centers  
USA  
Telephone: 800-366-2283 or 585-340-4162  
Fax: 800-366-1329  
Email: [email protected]  
Customer Service  
Telephone: 888-289-0096  
Fax: 585-223-9180  
Email: [email protected]  
Technical Support  
Telephone: 800-326-1450  
Fax: 585-223-3508 or 717-735-6560  
Email: [email protected]  
Repair Center  
Telephone: 585-421-4220  
Fax: 585-223-9180 or 717-735-6561  
Email: [email protected]  
Canada  
Telephone: 514-738-2434  
Fax: 514-738-8480  
Europe, Middle East & Asia Pacific Region  
Telephone: 44 (0) 1495 274558  
Fax: 44 (0) 1495 274280  
Email: [email protected]  
More information  
For additional information, please contact your Bosch Security Systems representative or visit  
our web site at www.boschsecurity.com  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
AutoDome 800 Series HD PTZ Camera  
2
Installing the Pendant Arm Wall, Corner, and Mast  
(Pole) Mounts  
2.1  
Unpacking  
This equipment should be unpacked and handled with care. If an item appears to have been  
damaged in shipment, notify the shipper immediately.  
Verify that all the parts listed in the Parts List below are included. If any items are missing,  
notify your Bosch Security Systems Sales or Customer Service Representative. See  
Section 1.4 Customer Support and Service, page 13 for contact information.  
The original packing carton is the safest container in which to transport the unit and must be  
used if returning the unit for service. Save it for possible future use.  
2.1.1  
Parts List  
The following table lists the parts included with the Pendant Arm Wall, Corner, or Mast mount  
packages.  
Mount Kit Options  
Part Numbers  
Pendant Arm (Only)  
VGA-PEND-ARM  
VGA-PEND-WPLATE  
Pendant Arm with Mounting Plate  
(24 V AutoDome models only, no power supply box)  
Pendant Arm with one of the following Power Supply Boxes:  
–
–
Power Box without transformer (24 VAC)  
VG4-A-PA0  
Power Box with 120 VAC transformer  
or with 230 VAC transformer  
VG4-A-PA1  
VG4-A-PA2  
Trim Skirt for Power Supply Box (optional)  
Corner Mount Kit  
VG4-A-TSKIRT  
–
Corner Mount Plate  
Mast (Pole) Mount Kit  
Mast Mount Plate  
Fiber Optic Ethernet Media Converter kit  
VG4-A-9542  
–
VG4-A-9541  
VG4-SFPSCKT  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en  
15  
2.1.2  
Description  
This chapter details how to install an AutoDome Pendant Arm to a wall, a corner, or to a mast  
(pole). Any variations to the installation procedures are noted.  
See Section 3 Installing Roof Parapet and Pipe Mounts, page 33 for a Roof (Parapet) or Pipe  
mount installation.  
2.1.3  
Tools Required  
–
–
–
–
–
–
5 mm Allen wrench (supplied)  
Small, straight-blade screwdriver - 2.5 mm (0.1 in.)  
No. 2 Phillips screwdriver  
Socket wrench and 9/16-in. socket  
Banding tool (Bosch P/N TC9311PM3T) - if installing a mast (pole) mount  
3/4 in. (20-mm) NPS right angle conduit connector - if installing a mast (pole) mount with  
a VG4-ARMPLATE  
2.2  
Pre-installation Checklist  
1. Determine the location and distance for the Power Supply Box based on its voltage and  
current consumption.  
You may choose to route the main power supply through an intermediate power supply  
box (VG4-PSU1 or VG4-PSU2) before connecting the power to the pendant arm power  
supply box (VG4-PA0). See Section 4 Cable and Wire Standards, page 51, for wiring  
information and distances.  
2. Use only UL listed liquid tight strain reliefs for conduits to the Power Supply Box to  
ensure that water cannot enter the box. You must use water tight conduits and fittings to  
meet NEMA 4 standards.  
WARNING!  
Power and I/O cabling must be routed separately inside different permanently earthed metal  
conduits.  
3. Route all rough wiring including: power, Ethernet, alarms I/O, relay I/O, and fiber optic  
cabling. See Section 4 Cable and Wire Standards, page 51, for video and control protocol  
methods.  
WARNING!  
Install external interconnecting cables in accordance to NEC, ANSI/NFPA70 (for US  
application) and Canadian Electrical Code, Part I, CSA C22.1 (for CAN application) and in  
accordance to local country codes for all other countries.  
Branch circuit protection incorporating a 20 A, 2-pole Listed Circuit Breaker or Branch Rated  
Fuses are required as part of the building installation. A readily accessible 2-pole disconnect  
device with a contact separation of at least 3 mm must be incorporated.  
4. Choose the appropriate AutoDome model for the environment in which it will be used.  
5. Choose the appropriate mounting kit to use, depending on the location of the AutoDome,  
either wall mount, corner mount, or mast (pole) mount.  
If the kit contains a Power Supply Box, refer to Section 2.3 Mount Power Supply Box,  
page 16.  
If you are using the Mounting Plate with a 24 V AutoDome, refer to Section 2.8 Installing  
the VG4-A-ARMPLATE, page 26.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
AutoDome 800 Series HD PTZ Camera  
CAUTION!  
Select a rigid mounting location to prevent excessive vibration to the AutoDome camera.  
2.3  
Mount Power Supply Box  
Before mounting the Power Supply Box decide if you should wire the box through the holes in  
the bottom or back of the box. If wiring the box through the back, move the two (2) seal plugs  
to the bottom through the holes before mounting.  
NOTICE! Use 3/4-inch (20-mm) NPS fittings for the holes on the bottom and back of the box.  
Use 1/2-inch (15-mm) NPS fittings for the side holes.  
Figure 2.1 Power Supply Wall (with optional trim skirt), Mast (Pole), and Corner Mounts  
1. Use the wall mount template supplied in the packaging box to locate the four mounting  
holes for the Power Supply Box.  
2. Drill four (4) holes for the mounting anchors. If installing outdoors, apply a weatherproof  
sealant around each hole at the mounting surface.  
WARNING!  
A stud diameter of 6.4 mm (1/4 inch) to 8 mm (5/16 inch) able to withstand a 120 kg (265 lb)  
pull-out force is recommended. The mounting material must be able to withstand this pull out  
force. For example, 19-mm (3/4-inch) minimum for plywood.  
3. Place the Power Supply Box into the optional Trim Skirt.  
4. Secure the Power Supply Box to the mounting surface.  
–
–
–
For a Wall installation: Use four (4) corrosion-resistant, stainless steel studs (not  
supplied). Then proceed to Step 5 below.  
For a Corner installation: Secure the Corner Plate to the wall corner using four (4)  
studs (not included). Then proceed to Step 5 below.  
For a Mast or a pole installation: The metal straps included with the Mast mount  
accommodate a pole with a diameter of 100–380 mm (4–15 in.). You must use a  
banding tool (sold separately) for a mast or pole installation. Follow the instructions  
provided with the banding tool to securely mount the Mast Plate to the pole.  
Contact your Bosch Sales Representative to order Banding Tool P/N TC9311PM3T.  
5. Secure the Power Supply Box to the Corner Plate or Mast Plate using the four (4) 3/8 x 1-  
3/4-inch bolts and split lock washers (supplied).  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en  
17  
6. Attach 3/4-inch (20-mm) NPS watertight pipe fittings (not supplied) to the bottom or  
back holes of the Power Supply Box through which you will run the power, video, and  
control data wires.  
2.4  
Route Wires and Attach Connectors  
Power wires must be routed to the left (front) side of the power supply box through a  
separate conduit. All video, control, and alarm wires must be routed through a second conduit  
to the right side of the box.  
If you plan to route the power through an intermediate power supply box, refer to  
Section 2.5 Route Power through Intermediate Power Supply Box, page 20.  
WARNING!  
External interconnecting cables are to be installed in accordance to NEC, ANSI/NFPA70 (for  
US application) and Canadian Electrical Code, Part I, CSA C22.1 (for CAN application) and in  
accordance to local country codes for all other countries.  
Branch circuit protection incorporating a 20 A, 2-pole Listed Circuit Breaker or Branch Rated  
Fuses are required as part of the building installation. A readily accessible 2-pole disconnect  
device with a contact separation of at least 3 mm must be incorporated.  
J102  
24 VAC  
P101  
(LED)  
24V NC 24V  
P106  
P105  
GND TXD RXD  
C+ C-  
GND TXD RXD ꢀꢀꢀ C+ C-  
Figure 2.2 Pendant Arm Power Supply Box  
1. Route all network, control, and alarm wires through the conduit fitting on the right side  
of the power box. See Section 4 Cable and Wire Standards, page 51, for fiber optic  
specifications and distances.  
2. Route the high voltage 115/230 VAC lines through the conduit fitting on the left side of  
the box. The Power Supply Box with a transformer comes with a barrier that separates  
the high voltage side on the left, from the low voltage 24 VAC side on the right.  
3. Cut and trim all wires with sufficient slack to reach their connector terminals in the box,  
but not so long as to be pinched by or to obstruct closing the Pendant Arm. See  
Figure 2.2, Page 17, above, for the connector locations.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
AutoDome 800 Series HD PTZ Camera  
4. Attach the supplied 3-pin Power Plug to the incoming power wires. See connector P101  
in Table 2.1, Page 20, for wire connections.  
5. Attach an RJ45 plug to the incoming Ethernet cable. If installing a Fiber Optic model,  
attach an ST fiber plug to the optic fiber cable. See Section 4 Cable and Wire Standards,  
page 51, for the different methods of transmitting video and control protocols, and wire  
specifications.  
6. If you are connecting alarm inputs and relay outputs, attach the supplied 4-wire Alarm  
Output and the 6-wire Alarm Input flying leads to the appropriate relay and alarm wires.  
WIRE  
1
2
3
4
WHITE  
BROWN  
ORANGE  
GREEN  
WIRE  
WHITE  
1
2
3
4
5
6
BROWN  
ORANGE  
GREEN  
YELLOW  
BLUE  
Figure 2.3 Alarm and relay connectors  
1
4-pin Alarm Output Flying Lead  
2
6-pin Alarm Input Flying Lead  
Wire Color  
Description  
Not used  
Not used  
Relay Out 1  
Relay Ground  
Wire Color  
Description  
1
2
3
4
White  
1
2
3
4
5
6
White  
Brown  
Orange  
Green  
Yellow  
Blue  
Alarm Input 1 (A3)  
Alarm Input 2 (A4)  
Not used  
Not used  
Not used  
Brown  
Orange  
Green  
Alarm Ground (AGND)  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
AutoDome 800 Series HD PTZ Camera  
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en  
19  
2.4.1  
Power Supply Box Connections  
The following figure is a detailed illustration of the Pendant Arm Power Supply Box, which  
includes the fuse specifications.  
TRANSFORMER  
(115/230VAC  
MODELS)  
J102  
P101  
(LED)  
24V NC 24V  
1 2 3  
P106  
P105  
GND TXD RXD ꢀꢀ C+ C-  
GND TXD RXD ꢀꢀ C+ C-  
6
5
4
3
2
1
6
5
4
3
2
1
Figure 2.4 Pendant arm power supply box  
1
2
3
4
5
6
Ground Screw  
From Harness  
In/Out; 1/2 in. (15 mm) NPS Fitting 9  
Ethernet (video and control)  
24 VAC to Dome  
7
8
P101 Connector; Power In  
P106 Connector; Audio In  
P105 Connector; Audio In to Dome  
10 Power In; 3/4 in. (20 mm) NPS Fitting  
11 Audio In; 3/4 in. (20 mm) NPS Fitting  
In/Out; 1/2 in. (15 mm) NPS Fitting  
WARNING!  
Fuse replacement by qualified service personnel only. Replace with same type fuse.  
Fuse Specifications  
Volts  
24 V  
XF101 Mains XF102 Camera XF103 Heater  
T 5.0 A  
T 1.6 A  
T 0.8A  
T 2.0 A  
T 2.0 A  
T 2.0 A  
T 3.15 A  
T 3.15 A  
T 3.15 A  
115 V  
230 V  
The following table lists the Power Supply Box connectors:  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
AutoDome 800 Series HD PTZ Camera  
No.  
Connector  
Pin 1  
Pin 2  
Pin 3  
Pin 4  
Pin 5  
Pin 6  
Ground  
Grounding Screw  
P101  
P105  
115/230 VAC or  
24 VAC Power In  
Line  
NC  
Neutral  
Data/Audio  
Audio  
Audio  
Earth  
Not Used  
Heater  
Ground  
P106  
P107  
Not Used  
24 VAC Power  
(Arm Harness)  
Dome  
Dome  
Earth  
Heater  
24 VAC  
24 VAC  
Ground (24 VAC)  
(24 VAC)  
Table 2.1 Power Supply Box Connections  
2.5  
Route Power through Intermediate Power Supply Box  
You may route the main power supply through a VG4-PSU1 (120 V transformer) or through a  
VG4-PSU2 (230 V transformer) Power Supply Box before connecting the power to a VG4-PA0  
(24 V, no transformer) Power Supply Box. The main issue with this configuration is that the 5-  
pin power out connector from the VG4-PSU1 or VG4-PSU2 does not match to the 3-pin power  
input of the VG4-PA0 power supply. The illustration below depicts:  
–
–
–
A VG4-PSU1/VG4-PSU2 Power Supply Box.  
The main power supply connected to the P101 connector and to the grounding screw.  
The 24 VAC power out wire connected to the P107 heater power connectors.  
VG4-PSU1 / VG4-PSU2  
J102  
P101  
(LED)  
24V NC 24V  
1 2 3  
P106  
P105  
GND TXD RXD  
C+ C-  
GND TXD RXD  
C+ C-  
6
5
4
3 2 1  
6 5 4
3
2 1  
Figure 2.5 VG4-PSU1/VG4-PSU2 Power Supply Box  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en  
21  
1
2
3
4
120/230 VAC Power In  
Ground Wire  
P101 Connector  
P107 Connector  
5
6
7
Transformer  
In/Out Conduit (1/2 in. [15 mm] NPS Fitting  
24 VAC Power Out to VG4-PA0  
To properly wire the incoming high voltage and the outgoing low voltage lines, refer to this  
table:  
No.  
Connector  
Pin 1  
Grounding Screw  
Line NC  
Pin 2  
Pin 3  
Pin 4  
Pin 5  
Pin 6  
Ground  
P101  
P107  
115/230 VAC Power In  
24 VAC Power Out  
Neutral  
Earth  
Heater  
Heater  
Ground  
(24 VAC)  
(24 VAC)  
Table 2.2 VG4-PSU1/VG4-PSU2 Power Supply Box Connections  
1. Route the high voltage 115/230 VAC lines through the conduit fitting on the left side of  
the box. The Power Supply Box with a transformer comes with a barrier that separates  
the high voltage side on the left, from the low voltage 24 VAC side on the right.  
2. Cut and trim the high voltage 115/230 VAC power and ground wires with sufficient slack  
to reach their connector terminal in the box, but not so long as to be pinched by or to  
obstruct closing the cover door.  
3. Attach the supplied 3-pin power plug to the incoming high voltage power wires in the  
box. Refer to connector P101 in Table 2.2, Page 21 and to the image below for an  
illustration of these connections:  
P101  
24V NC 24V  
1 2 3  
Figure 2.6 Incoming 115/230 VAC power supply  
4. Attach the ground wire to the grounding screw.  
5. Connect three wires to the P107 Power Out connector to route the 24 VAC power supply  
to the VG4-PA0 Power Supply Box.  
a. Connect the first wire to pin 5 (HN: Heater Neutral) connector.  
b. Connect the second wire to pin 4 (HL: Heater Line) connector.  
c. Connect the third wire to pin 3 (Earth Ground) connector.  
Refer to connector P107 in Table 2.2 and to the image below for an illustration of  
these connections:  
Figure 2.7 Outgoing 24 VAC power supply  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
AutoDome 800 Series HD PTZ Camera  
WARNING!  
Ensure that you connect the outgoing power supply wires to the P107 heater connectors (HN  
and HL). The heater power (XF103) fuse can handle a higher amperage (3.15 A) than the  
camera power (XF102) fuse (2.0 A).  
6. Route the 24 VAC outgoing power supply wires into the VG4-PA0 power supply box  
through the conduit fitting on the left side of the box.  
7. Cut and trim the 24 VAC power and ground wires with sufficient slack to reach their  
connector terminal in the box, but not so long as to be pinched by or to obstruct closing  
the cover door.  
8. Attach the supplied 3-pin power plug to the incoming 24 VAC power wires in the box, as  
illustrated below.  
J102  
P101  
(LED)  
24V NC 24V  
1 2 3  
P106  
P105  
GND TXD RXD  
C+ C-  
GND TXD RXD  
C+ C-  
6
5
4 3 2 1  
6 5 4 3 2 1  
Figure 2.8 VG4-PA0 Power Supply Box  
1
2
3
4
Incoming 24 VAC Power Supply Wires (from VG4-PSU1/VG4-PSU2 power supply box)  
Ground Wire  
P101 Connector  
Ethernet (Video and Control)  
9. Follow the instructions in Section 2.6 Attach Pendant Arm to Power Supply Box, page 22, to  
continue the installation.  
2.6  
Attach Pendant Arm to Power Supply Box  
The bottom hinge pin of the Pendant Arm is provided with a Hinge Pin Stop to hold the hinge  
open while attaching the arm to the Power Supply Box.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en  
23  
1. Compress the bottom hinge pin by pushing the pin lever downward and rotating it  
behind the Hinge Pin Stop.  
Figure 2.9 Pendant Arm to Power Box Hinge Alignment  
2. Open the top hinge by pushing its pin lever up and holding it.  
NOTICE! Both Hinge Pins must be fully compressed to open (unlock) the hinges of the  
Pendant Arm and before proceeding to the next step.  
3. While continuing to hold the top hinge pin open and align the top and bottom hinges of  
the Pendant Arm to their mating points on the Power Supply Box. See Figure 2.9, above,  
for an illustration.  
4. Once you have the hinges aligned, release the top hinge pin to engage its mating hinge on  
the power box. Then release the bottom hinge pin from the Hinge Pin Stop to lock the  
Pendant Arm to the Power Supply Box.  
WARNING!  
Serious injury or death can occur if the hinge pins of the Pendant Arm are not fully engaged  
(locked) to the Power Supply Box. Exercise caution before releasing the Pendant Arm.  
2.7  
Make Connections in Power Supply Box  
Refer to Table 2.2, Page 21 to locate the various connectors in the power supply box and make  
the following connections detailed below.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
AutoDome 800 Series HD PTZ Camera  
1 2 3  
Figure 2.10 Pendant Arm connections to Power Supply Box  
1. Attach the earth ground wire (item 1 in the illustration above) to the grounding screw on  
the left side of the power box.  
2. Connect the 6-pin Control/Audio cable, installed previously, to its mating connector P106  
in the power box.  
3. Connect the 6-pin Control to Dome Plug from the Pendant Connector Harness to its  
matting connector P105 in the power box.  
Coax Video  
Control/Audio  
24 VAC Power  
Ethernet Video and  
Control  
(not used)  
Alarm Inputs  
WARNING!  
Alarm Outputs  
Relays  
Grounding Strap  
Do not connect the RJ45 connector unless using UTP video or Ethernet.  
4. Connect the 5-pin, 24 VAC to Dome Plug from the Pendant Connector Harness to its  
corresponding color mating connector P107 on the right side of the box.  
5. To connect alarm Inputs and the alarm output, connect the 4-pin Alarm Out and the 6-pin  
Alarm In connectors from the Pendant Connector Harness to their mating connectors,  
installed previously, to the incoming alarm wires.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en  
25  
6. Connect the 3-pin Power In Plug, installed previously, to its matting connector P101 on  
the left side of the box.  
7. If installing a Fiber Optic model attach the incoming ST fiber plug, installed previously, to  
its mating connector on the Fiber Optic Module in the power supply box. Then attach the  
Ethernet cable to its mating connector from the Pendant Connector Harness. See  
Section 4 Cable and Wire Standards, page 51 for fiber optic specifications.  
(GND)  
24V NC 24V  
GND TXD RXD ꢀꢀ C+ C-  
Figure 2.11 Optional Fiber Optic Module  
1
2
3
4
Transformer  
Ethernet to Dome  
In/Out  
5
6
7
8
In/Out  
ST Connector (Fiber)  
Power In  
From Arm Harness  
Data In/Out  
8. Connect the incoming RJ45 connector, installed previously, to its mating connector from  
the Pendant Connector Harness. See Section 4 Cable and Wire Standards, page 51 for  
connections and specifications.  
9. Attach the grounding strap of the Pendant Arm to the Power Supply Box. See Figure 2.10,  
Page 24.  
10. After making the harness connections to the Power Supply Box, rotate the Pendant Arm  
to close and seal the Power Supply Box and tighten the two (2) captive screws to  
10-12 N-m (90-105 in.-lbs).  
11. Refer to Section 2.9 Attach Pendant to Arm and Tighten, page 31, to continue the  
AutoDome Installation procedure.  
NOTICE! After all wiring is complete, close the cover door and tighten the two (2) captive  
screws on the cover door to 10-12 N-m (90-105 in.-lbs) to ensure the Power Supply Box is  
watertight.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
AutoDome 800 Series HD PTZ Camera  
2.8  
Installing the VG4-A-ARMPLATE  
This section provides instructions to install a wall, corner, or mast mount with the VG4-A-  
ARMPLATE Mounting Plate instead of a Power Supply Box.  
CAUTION!  
You must route the main power supply through a 120/230 VAC transformer (VG4-PSU1 or  
VG4-PSU2 power supply box) before connecting the power to a 24 VAC AutoDome.  
WARNING!  
A stud diameter of 6.4 mm (1/4 inch) to 8 mm (5/16 inch) able to withstand a 120 kg (265 lb)  
pull-out force is recommended. The mounting material must be able to withstand this pull out  
force. For example, 19-mm (3/4-inch) minimum for plywood.  
1. For a Corner installation:  
a. Secure the Corner Plate to the wall corner using four (4) studs (not included).  
b. Secure the Mounting Plate to the Corner Plate using the four (4) 3/8 x 1-3/4-inch  
bolts and split lock washers (supplied).  
2. For a Mast or pole installation:  
The metal straps included with the Mast mount accommodate a pole with a diameter of  
100–380 mm (4–15 in.). You must use a banding tool (sold separately) for a mast or pole  
installation. In addition, you must obtain a 3/4 in. (20-mm) right angle conduit connector  
through which you route the wires that connect to the pendent arm.  
a. Follow the instructions provided with the banding tool to securely mount the Mast  
Plate to the pole. Contact your Bosch Sales Representative to order Banding Tool  
P/N TC9311PM3T.  
b. Secure the Mounting Plate to the Mast Plate using the four (4) 3/8 x 1-3/4-inch bolts  
and split lock washers (supplied).  
c. Remove one of the rubber gaskets from the Mounting Plate.  
d. Once the Mounting Plate (item 1, below) is attached to the Mast Plate (item 2),  
connect the right angle conduit (item 3) to the Mounting Plate through the empty  
conduit hole as shown below:  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en  
27  
3. Ensure that the mounting plate is secure.  
2.8.1  
Attach the Pendant Arm to the Mounting Plate  
The bottom hinge pin of the Pendant Arm is provided with a Hinge Pin Stop to hold the hinge  
open while attaching the arm to the Mounting Plate.  
1. Compress the bottom hinge pin by pushing the pin lever downward and rotating it  
behind the Hinge Pin Stop.  
Figure 2.12 Connect Pendant Arm to Mounting Plate  
2. Open the top hinge by pushing its pin lever up and holding it.  
Note: Both Hinge Pins must be fully compressed to open (unlock) the hinges of the  
Pendant Arm and before proceeding to the next step.  
3. While continuing to hold the top hinge pin open, align the top and bottom hinges of the  
Pendant Arm to their mating points on the Mounting Plate. See Figure 2.12, above, for an  
illustration.  
4. Once you have the hinges aligned, release the top hinge pin to engage its mating hinge on  
the Mounting Plate. Then release the bottom hinge pin from the Hinge Pin Stop to lock  
the Pendant Arm to the Mounting Plate.  
2.8.2  
Route and Connect Wires to a Power Supply Box  
The illustration below depicts the power and control cables connected to the Pendant Arm:  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
AutoDome 800 Series HD PTZ Camera  
Figure 2.13 Pendant Arm Cables  
Cable Cable  
Cable Cable  
1
2
3
Grounding Strap (black)  
24 VAC Power (red)  
Relay Contacts (yellow)  
5
6
7
Ethernet Video and Control (blue)  
Alarm Outputs (white)  
Alarm Inputs (gray)  
(not used)  
4
Coax Video (black)  
8
Audio In (green)  
(not used)  
1. Route all incoming wires through one of the conduits at the bottom of the Mounting  
Plate. For a mast mount, route all wires through the right-angle conduit.  
2. Attach the water-tight plug to the other conduit.  
3. Attach the grounding spade terminal (item 1, below) to one of the spade terminals inside  
the Mounting Plate.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en  
29  
Figure 2.14 Mounting Plate - Inside Detail  
Ref. Description  
1
2
3
Grounding lug with two spade terminals  
Earth ground lug with crimp ring terminal  
Wire input conduit holes  
4. Connect the incoming 24 VAC power wires to the 5-pin, 24 VAC Power In mating  
connector (supplied with the Mounting Plate kit) for the Dome and for the Heater.  
5. Attach the grounding spade from the 5-pin mating connector (item 1, Figure 2.14) to the  
other spade terminal inside the mounting plate.  
6. Attach the 5-pin Power In mating connector to the 24 VAC Power cable (cable 2)  
connected to the pendant.  
7. Connect the incoming RJ45 video connector, installed previously, to the Ethernet cable  
(cable 5). Refer to Section 4 Cable and Wire Standards, page 51, for detailed wire and  
connection information.  
8. Connect the outgoing alarm wires to the flying leads coming from the 4-pin Alarm  
Outputs cable (cable 6).  
9. Connect the incoming alarms wires to the flying leads coming from the 6-pin Alarm Inputs  
cable (cable 7).  
10. Connect the incoming Audio In wires to the 6-pin mating connector supplied with the  
VG4-A-ARMPLATE kit. Ensure that the 100 Ω resistor has been removed between C-  
(Audio -) and the C+ (Audio +) terminals.  
Refer to Section 4 Cable and Wire Standards, page 51, for detailed wire and connection  
information.  
11. Attach the 6-pin Audio In mating connector to the Audio In (cable 8) cable.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
AutoDome 800 Series HD PTZ Camera  
12. Connect the Earth ground wire, if available, to the crimp ring terminal inside the  
Mounting Plate. Refer to Figure 2.14 above.  
Note: The Earth ground is not provided with the VG4-A-ARMPLATE kit; it is a ground  
connection made at the installed location.  
13. After making the harness connections to the Mounting Plate, rotate the Pendant Arm to  
close and tighten the two (2) captive screws to 10-12 N-m (90-105 in.-lbs).  
14. Refer to Section 2.9 Attach Pendant to Arm and Tighten, page 31, to continue the  
AutoDome Installation procedure.  
NOTICE! After all wiring is complete, close the cover door and tighten the two (2) captive  
screws on the cover door to 10-12 N-m (90-105 in.-lbs).  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en  
31  
2.9  
Attach Pendant to Arm and Tighten  
CAUTION!  
The bubble is packaged with a protective plastic sheet. It is recommended that the bubble  
remain stored this way until it is ready to install. Limit handling the bubble, as any scratches  
can quickly affect visibility.  
NOTICE! Before attaching the AutoDome Pendant, visually inspect the dome and arm  
connectors for any blocked pin holes or bent pins.  
1. Tilt the bottom of the dome toward the pendant arm base and place the mounting hook,  
located on top of the dome housing, over the recessed hinge pin of the arm.  
a
b
Figure 2.15 Attach Pendant to Arm  
1
2
Tilt up.  
Hook and drop.  
2a Recessed Hinge Pin  
2b Dome Connector  
3
4
Rotate down to engage dome connector.  
Tighten the two (2) mounting screws to a minimum torque of 10-12 N-m (90-105 in.-lbs).  
2. Drop the dome housing down slightly to engage the dome housing hook on the Pendant  
Arm hinge pin, allowing the dome to rotate around the pin.  
3. Rotate the dome housing down to a vertical position and gently push upward to engage  
the connector on top of the dome housing.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
32 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts  
AutoDome 800 Series HD PTZ Camera  
CAUTION!  
If you feel any resistance when rotating the dome housing or when engaging the connector,  
stop immediately and start over.  
4. Hold the Pendant housing in position while tightening the two (2) 5-mm Allen head  
mounting screws on top of the housing to 10-12 N-m (90-105 in.-lbs).  
CAUTION!  
You must tighten the two mounting screws to a minimum torque of 10-12 N-m (90-105 in.-lbs)  
to ensure a proper seal between the arm and the housing.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing Roof Parapet and Pipe Mounts | en  
33  
3
Installing Roof Parapet and Pipe Mounts  
3.1  
Unpacking  
This equipment should be unpacked and handled with care. If an item appears to have been  
damaged in shipment, notify the shipper immediately.  
Verify that all the parts listed in the product's Parts List below are included. If any items are  
missing, notify your Bosch Security Systems Sales or Customer Service Representative. See  
Section 1.4 Customer Support and Service, page 13 for Customer Support and Service contact  
information.  
The original packing carton is the safest container in which to transport the unit and must be  
used if returning the unit for service. Save it for possible future use.  
3.1.1  
Parts List  
The following table lists the parts included with the Roof Parapet and Pipe mount packages:  
Mount Kit Options  
Part Numbers  
Parapet (Roof) Mount and  
VGA-ROOF-MOUNT  
VG4-A-9543  
Pipe Mount with one of the following Power Supply Boxes:  
–
Power Supply Box with 120 VAC transformer  
or 230 VAC transformer  
VG4-A-PSU1  
VG4-A-PSU2  
Optional Flat Roof Mount Adapter for VGA-ROOF-MOUNT Mount (not  
included)  
LTC 9230/01  
Pipe Mount with one of the following Power Supply Boxes:  
VG4-A-9543  
–
Power Supply Box with transformer 120 VAC  
or 230 VAC transformer  
VG4-A-PSU1  
VG4-A-PSU2  
Trim Skirt for Power Supply Box (optional)  
Fiber Optic Ethernet Media Converter kit  
VG4-A-TSKIRT  
VG4-SFPSCKT  
3.1.2  
Description  
This chapter details how to install an AutoDome to a Roof Parapet or to a Pipe mount. Any  
differences to the installation between these two mounting systems are noted. See  
Section 2 Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts, page 14 for this type  
of application.  
The VG4-A-9230 Series are stationary mounts intended for rooftop parapet vertical walls. They  
are made of light weight aluminum with a corrosion-resistant finish and are used for all Bosch  
AutoDome Camera systems up to a rated load of 29 kg (64 lb). These mounts can be fitted to  
the inside or outside of parapet walls and can swivel for ease of positioning and for servicing  
the AutoDome.  
3.1.3  
Tools Required  
–
–
–
–
–
–
–
5 mm Allen wrench (supplied)  
Small straight blade screwdrivers ~ 2.5 mm (0.1 in.) – 3.1 mm (1/8 in.)  
Medium straight blade screwdriver  
No. 1 and No. 2 Phillips screwdrivers  
Socket wrench and 9/16 in. socket  
Pipe Wrench  
Barrel connector (if installing a fiber optic model)  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
34 en | Installing Roof Parapet and Pipe Mounts  
AutoDome 800 Series HD PTZ Camera  
3.2  
Pre-installation Check List  
1. Determine the location and distance for the power supply box based on its voltage and  
current consumption. See Section 4 Cable and Wire Standards, page 51 for wiring  
information and distances.  
2. Use only UL listed liquid tight strain reliefs for conduits to the Power Supply Box to  
ensure that water cannot enter the box. You must use water tight conduits and fittings to  
meet NEMA 4 standards.  
NOTICE! Power and I/O cabling must be routed separately inside different permanently  
earthed metal conduits.  
3. Install all rough wiring including: power, Ethernet, alarms I/O, relay I/O, and fiber optic  
cabling. See Section 4 Cable and Wire Standards, page 51 for video and control protocol  
methods.  
WARNING!  
External interconnecting cables are to be installed in accordance to NEC, ANSI/NFPA70 (for  
US application) and Canadian Electrical Code, Part I, CSA C22.1 (for CAN application) and in  
accordance to local country codes for all other countries.  
Branch circuit protection incorporating a 20 A, 2-pole Listed Circuit Breaker or Branch Rated  
Fuses are required as part of the building installation. A readily accessible 2-pole disconnect  
device with a contact separation of at least 3 mm must be incorporated.  
4. Choose the appropriate AutoDome model for the environment in which it will be used.  
5. Choose the appropriate mounting kit to use depending on the location of the AutoDome:  
Parapet (Roof) mount or the Pipe mount.  
CAUTION!  
Select a rigid mounting location to prevent excessive vibration to the AutoDome camera.  
3.3  
Mount Power Supply Box  
Before mounting the Power Supply Box decide if you will be wiring the box through the holes  
in the bottom or back of the box. If wiring the box through the back, move the two (2) seal  
plugs to the bottom holes before mounting.  
NOTICE! Use 3/4-inch NPS (20-mm) fittings for the holes on the bottom and back of the box.  
Use 1/2-inch NPS (15-mm) fittings for the side holes. See Section 3.1.1 Parts List, page 33, for  
an illustration.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing Roof Parapet and Pipe Mounts | en  
35  
Figure 3.1 Wall Mount Power Supply with Optional Trim Skirt  
1. Use the wall mount template supplied in the packaging box to locate the four (4)  
mounting holes for the Power Supply Box.  
2. Drill four (4) holes for the mounting anchors. If installing outdoors, apply a weatherproof  
sealant around each hole at the mounting surface.  
3. Place the Power Supply Box into the optional Trim Skirt.  
4. Secure the Power Supply Box to the wall using four (4) corrosion-resistant stainless steel  
studs (not included).  
NOTICE! A stud diameter of 6.4 mm (1/4 in.) or 8 mm (5/16 in.), able to withstand a 120 kg  
(265 lb) pull-out force is recommended.  
5. Attach the 3/4 in. (20 mm) watertight pipe fittings (not supplied) to the holes of the  
Power Supply Box through which you will run the power, video, and control data wires.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
36 en | Installing Roof Parapet and Pipe Mounts  
AutoDome 800 Series HD PTZ Camera  
3.3.1  
Attach Cover Door  
1. Compress the bottom hinge pin by pushing the pin lever down and then rotate it behind  
the Hinge Pin Stop. The power box Cover Door provides a Hinge Pin Stop to hold the  
bottom hinge open while attaching the door.  
90o  
24V NC 24V  
GND TXD RXD ꢀꢀꢀ C+ C-  
GND TXD RXD ꢀꢀꢀ C+ C-  
Figure 3.2 Align Cover Door Hinge to Power Box  
1
2
3
4
Power Supply Box  
Cover Door  
Align Top Hinge  
Align Bottom Hinge  
5
6
7
Hold Hinge Pin Open  
Open Position  
Hinge Pin Stop  
2. Open the top hinge by pushing its pin lever outward and holding it open.  
Note: Both Hinge Pins must be fully compressed to open (unlock) the female hinges of  
the Cover Door before proceeding to the next step.  
3. While holding the top hinge pin open, position the Cover Door to the Power Supply Box  
and align its hinges.  
4. When the hinges are aligned, release the top hinge pin to engage its mating hinge on the  
power box. Then release the bottom hinge pin from the Hinge Pin Stop to complete  
attaching the cover door to the Power Supply Box.  
NOTICE! After all wiring is complete, close the cover door and tighten the two (2) captive  
screws on the cover door to 10-12 N-m (90-105 in.-lbs) to ensure the Power Supply Box is  
watertight.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing Roof Parapet and Pipe Mounts | en  
37  
3.4  
Route Wires and Attach Connectors  
Power wires must be routed to the left (front) side of the Power Supply Box through a  
separate conduit. All video, control, and alarm wires must be routed through a second conduit  
to the right side of the box. See Section 4 Cable and Wire Standards, page 51 for methods of  
transmitting video and data, and for wire specifications.  
WARNING!  
External interconnecting cables are to be installed in accordance to NEC, ANSI/NFPA70 (for  
US application) and Canadian Electrical Code, Part I, CSA C22.1 (for CAN application) and in  
accordance to local country codes for all other countries.  
Branch circuit protection incorporating a 20 A, 2-pole Listed Circuit Breaker or Branch Rated  
Fuses are required as part of the building installation. A readily accessible 2-pole disconnect  
device with a contact separation of at least 3 mm must be incorporated.  
There are two possible methods to route the video, control, and alarm wires:  
–
One is to route the power, ethernet, and alarm wires through the conduit fitting on the  
right (front) side of the Power Supply Box and out to the AutoDome Interface Board.  
J102  
P101  
(LED)  
24V NC 24V  
P106  
P105  
GND TXD RXD ꢀꢀ C+ C-  
GND TXD RXD ꢀꢀ C+ C-  
Figure 3.3 VG4-A-PSU1 or VG4-A-PSU2 Power Supply Box  
1
2
3
4
120 VAC/230 VAC Power In  
P101 Connector  
Ground Connection  
Transformer  
5
6
7
Ethernet Video and Control Wire  
24 VAC Power Out  
P107 Connector  
–
The second method is to bypass the Power Supply Box and route the ethernet and alarm  
wires directly to the Interface Board. You connect only the power wires inside the Power  
Supply Box.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
38 en | Installing Roof Parapet and Pipe Mounts  
AutoDome 800 Series HD PTZ Camera  
BNC  
AGND  
OUT 3  
OUT 2  
OUT 1  
J102  
AGND  
A7  
A6  
A5  
A4  
A3  
P101  
(LED)  
24V NC 24V  
P106  
P105  
GND TXD RXD ꢀꢀ C+ C-  
GND TXD RXD ꢀꢀ C+ C-  
J 1 0 1  
P 1 0 6  
Figure 3.4 VG4-A-PSU1 or VG4-A-PSU2 Power Supply Box Connected to Pipe Interface Board  
VG4-A-PSU1/VG4-A-PSU2  
120 VAC/230 VAC Power In  
P101 Connector  
Ground Connection  
Transformer  
Pipe Interface Board  
P101 Connector  
P107 Connector  
1
2
3
4
5
6
7
8
9
24 VAC Power In (to AutoDome)  
10 Earth Ground  
24 VAC Power Out  
P107 Connector  
11 24 VAC Power In (to AutoDome)  
12 24 VAC Power In (to Heater)  
13 24 VAC Power In (to Heater)  
14 AutoDome Power  
15 Heater Power  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
AutoDome 800 Series HD PTZ Camera  
Installing Roof Parapet and Pipe Mounts | en  
39  
3.4.1  
Wiring the Power Supply Box  
1. Route the high voltage 115/230 VAC lines through the conduit fitting on the left side of  
the box.  
NOTICE! The Power Supply Box with transformer comes with a barrier that separates the high  
voltage side on the left from the low voltage 24 VAC side on the right.  
2. Cut and trim the high voltage 115/230 VAC power and ground wires with sufficient slack  
to reach their connector terminal in the box, but not so long as to be pinched by or to  
obstruct closing the Cover Door. See Section 3.1.1 Parts List, page 33, for connector  
location.  
3. Attach the supplied 3-pin Power Plug to the incoming high voltage power wires in the  
box. See connector P101 in Table 3.1, Page 42.  
4. Route the low power 24 VAC wires from the right side of the Power Supply Box out to  
where the AutoDome will be mounted. Attach the supplied 5-pin 24 VAC Dome plug to  
the wire ends inside the box. See connector P107 in Table 3.1, Page 42.  
5. Route the Ethernet cable out to where the AutoDome will be mounted. See  
Section 4 Cable and Wire Standards, page 51 for fiber optic specifications.  
NOTICE! All ethernet and alarm wires either pass through the Power Supply Box or by-pass it  
and connect directly to the Pipe Interface Board.  
3.4.2  
Wiring the Fiber Optic Model  
If installing a Fiber Optic model, bring the fiber optic cable into the right side of the  
power supply box.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
40 en | Installing Roof Parapet and Pipe Mounts  
AutoDome 800 Series HD PTZ Camera  
(GND)  
24V NC 24V  
GND TXD RXD ꢀꢀ C+ C-  
1
2
3
4
Transformer  
Ethernet to Dome  
In/Out  
5
In/Out  
ST Connector (Fiber)  
Power In  
6
7
8
From Arm Harness  
Data In/Out  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing Roof Parapet and Pipe Mounts | en  
41  
3.4.3  
Power Supply Box Connections  
The following figure is a detailed illustration of the Roof or Pipe Mount Power Supply Box,  
which includes the fuse specifications.  
J102  
P101  
(LED)  
CONTROL  
IN/OUT  
P106  
CONTROL  
TO DOME  
P105  
24V NC 24V  
1 2 3  
GND TXD RXD  
C+ C-  
GND TXD RXD  
C+ C-  
6
5
4
3
2
1
6
5
4
3
2
1
1
2
3
4
Ground Screw  
5
Power In  
Transformer (115/230 VAC Modes) 6 In/Out; 1/2 in. (15 mm) NPS Fitting  
In/Out to Dome  
24 VAC to Dome Interface Board  
7
8
Power In; 3/4 in. (20 mm) NPS Fitting  
Audio and Ethernet Data and Video In/Out; 3/4  
in. (20 mm) NPS Fitting  
WARNING!  
Fuse replacement by qualified service personnel only. Replace with same type fuse.  
Fuse Specifications  
Volts  
24 V  
XF101 Mains  
T 5.0 A  
XF102 Camera XF103 Heater  
T 2.0 A  
T 2.0 A  
T 2.0 A  
T 3.15 A  
T 3.15 A  
T 3.15 A  
115 V  
230 V  
T 1.6 A  
T 0.8A  
The following table lists the Power Supply Box connectors:  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
42 en | Installing Roof Parapet and Pipe Mounts  
AutoDome 800 Series HD PTZ Camera  
No.  
Connector  
Pin 1  
Pin 2  
Pin 3  
Pin 4  
Pin 5  
Pin 6  
Ground  
Grounding Screw  
P101  
P105  
115/230 VAC or  
24 VAC Power In  
Line  
NC  
Neutral  
Data/Audio  
Audio  
Audio  
Earth  
Not Used  
Heater  
Ground  
P106  
P107  
Not Used  
24 VAC Power  
(Arm Harness)  
Dome  
Dome  
Earth  
Heater  
24 VAC  
24 VAC  
Ground (24 VAC)  
(24 VAC)  
Table 3.1 Power Supply Box Connections  
3.5  
Installing the VG4-A-9230 Roof Parapet Mount  
This section details the installation steps for the Roof Parapet Mount. If you are installing a  
pipe mount, see Section 3.6 Installing the VG4-A-9543 Pipe Mount, page 45, for instructions.  
Figure 3.5 VGA-A-9230 Parapet Roof Mount  
1. Determine the wall location on the roof for the AutoDome and use the Parapet wall  
mount bracket as a template to mark the hole locations.  
NOTICE! Allow enough room below the Parapet Mount Bracket to route the video, control and  
alarm wires up through the Parapet arm. In certain installations you may have to lift the  
Parapet arm for the AutoDome to clear the top of the wall when it is swung into position.  
Provide enough slack in the wires to rotate the pipe arm over the roof and back when camera  
maintenance is required.  
2. Prepare the mounting surface for the type of fastener by drilling holes for the mounting  
anchors as required.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing Roof Parapet and Pipe Mounts | en  
43  
Figure 3.6 Parapet Wall Mount Bracket and Roof Mount Plate  
1
2
3
Pipearm  
Parapet Wall Bracket  
3/8-16 SS Hex Head Bolt (supplied) 6  
4
5
Apply sealant around each fastener hole  
Roof Mount Plate  
Use a minimum of six (6) fasteners (not  
supplied). Eight (8) fastener holes shown.  
NOTICE! Fasteners are not supplied with the Roof Parapet Mount Kit since it depends on the  
material to which it is attached. The material must accommodate a minimum pull out strength  
of 275 kg (600 lbs). For example, 19 mm (3/4 inch) minimum for plywood. Fasteners can  
include bolts, studs, or lag bolts. All fasteners must be made of corrosion-resistant stainless  
steel, with a diameter of 10 mm (3/8 inch).  
All bolts must fully extend through the mounting surface and be secured with a flat washer,  
lock washer and a nut. All studs must be anchored to concrete or welded to a steel backing  
plate. Anchor bolts can be used for blind structures where there is no access to the rear.  
3. Apply a weatherproof sealant around each fastener hole at the mounting surface.  
4. Attach the Parapet Wall Bracket using at least six (6) stainless steel fasteners, three (3)  
on each side (the bracket has eight (8) holes). Be careful not to over tighten the  
fasteners because it may strip the threads. If attaching the parapet mount to a flat roof,  
attach the optional LTC 9230/01 Roof Mount Plate to the roof and then attach the  
Parapet Wall Bracket to the Roof Mount Plate.  
5. Insert the Parapet Pipe Arm into the mounting bracket until it bottoms in the bracket.  
6. Remove the End Cap from the front of the arm and feed the video, control, and power  
wires up through the bottom of the pipe arm and out the front end.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
44 en | Installing Roof Parapet and Pipe Mounts  
AutoDome 800 Series HD PTZ Camera  
Figure 3.7 VG4-A-9230 Parapet Mount  
1
2
End Cap with O-ring  
Parapet Pipe Arm  
3
4
5
1/4-20 SS Cap Screw  
Down Pipe  
10-24 SS Pan Head Screw  
7. Fold the Ethernet and power wires back at the front end of the arm and route them down  
and out through the Down Pipe. Then replace the End Cap.  
8. Wrap at least five layers of Teflon tape around the Down Pipe threads.  
9. Apply the supplied thread sealant to the Down Pipe threads:  
–
–
–
Make sure all surfaces are clean and dry.  
Apply a bead of sealant completely around the leading threads of the male fitting.  
Force the adhesive into the threads to thoroughly fill all voids.  
10. Thread the Dome Cap onto the down pipe and tighten securely. See the illustration  
below.  
WARNING!  
You must thread the Dome Cap onto the Down Pipe until it is tight. Failure to do so can result  
in damage, serious injury, or death.  
Figure 3.8 Attach Dome Cap  
1
2
Thread Sealant or tape  
Dome Cap  
11. Run a bead of RTV Silicon sealant around the down pipe/Dome Cap interface to seal any  
gaps between the down pipe and the Dome Cap.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing Roof Parapet and Pipe Mounts | en  
45  
12. Proceed to Section 3.7 Wire the Pipe Interface Board, page 46.  
NOTICE! Use a guy-wire to aid in stabilizing the Parapet Arm. Replace the 1/4 inch cap screw  
with a threaded 1/4-inch stainless steel eye bolt (not supplied). Loop the guy-wire through the  
eye bolt and attach both ends to anchor spots on the roof. See Figure 3.7, Page 44.  
3.6  
Installing the VG4-A-9543 Pipe Mount  
This section details the installation steps for the VG4-A-9543 Pipe Mount. If you are installing  
the Roof Parapet mount, see Figure 3.7, Page 44, for instructions.  
NOTICE! Customer must supply 1-1/2 inch (NPS) pipe threaded on both ends with a minimum  
length of 5 inches (12.7 cm).  
5 in.  
min.  
12.7 cm  
Figure 3.9 Pipe Mount  
1
2
3
Gasket  
Flange  
Cap  
1. Before installing the Top-Mounting Flange, ensure there is an adequate opening in the  
ceiling or mounting structure for the wires to pass through.  
2. Secure the pipe Flange with supplied gasket to the ceiling or other supporting structure  
using four (4) 10-mm (3/8-inch) diameter fasteners.  
NOTICE! Each fastener must have a minimum pullout strength of 275 kg (600 lbs). The  
mounting material must be able to withstand this pull-out force. For example, 19-mm (3/4-  
inch) minimum for plywood.  
3. Attach pipe (not supplied) to the Top-mounting Flange.  
WARNING!  
You must thread the pipe onto the Top-mounting Flange until it is tight. Failure to do so can  
result in damage, serious injury or death.  
4. Route the power, Ethernet and alarm wires through the Top-Mounting Flange and down  
the pipe.  
5. Wrap at least five layers of Teflon tape around the threads.  
6. Apply the supplied thread sealant to the threads on the Pipe.  
–
–
–
Make sure all surfaces are clean and dry.  
Apply a bead of sealant completely around the leading threads of the male fitting.  
Force the adhesive into the threads to thoroughly fill all voids.  
Bosch Security Systems, Inc.  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
F.01U.273.797 | 5.0 | 2012.08  
46 en | Installing Roof Parapet and Pipe Mounts  
AutoDome 800 Series HD PTZ Camera  
7. Thread the Pipe Cap onto the down pipe and tighten securely to prevent leaks. See  
Figure 3.9, Page 45.  
WARNING!  
You must thread the Dome Cap onto the pipe until it is tight. Failure to do so can result in  
damage or serious injury or death.  
3.7  
Wire the Pipe Interface Board  
This section provides instructions for connecting wires and cables to the Pipe Interface  
Board, as illustrated below. See Section 4 Cable and Wire Standards, page 51 for cable and  
wiring recommendations and specifications.  
BNC  
6
5
4
3
2
1
7
6
5
4
AGND  
OUT 3  
3
2
1
OUT 2  
OUT 1  
AGND  
A7  
A6  
A5  
A4  
A3  
3
2
1
2
1
J 1 0 1  
P 1 0 6  
Figure 3.10 Pipe Interface Board Connections  
Ref. Description  
Connector Wire Gauge Pin Description  
1
2
Pipe Interface Module  
Video Coax In (not used)  
J102  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing Roof Parapet and Pipe Mounts | en  
47  
Ref. Description  
Connector Wire Gauge Pin Description  
3
6-pin Alarm Input Flying Lead  
P103  
1
2
3
4
5
6
1
2
3
4
Alarm In 1  
Alarm In 2  
Not used  
Not used  
Not used  
Alarm Ground  
Not used  
Not used  
Relay Out 1  
Relay Ground  
Alarms In (1-2)  
4
4-pin Alarm Outputs Flying Lead  
Relay Out (1)  
P102  
5
6
100 Ω Resistor  
Audio  
P105  
P105  
1
2
3
4
5
Audio- (C-)  
Audio+ (C+)  
NC  
NC  
NC  
NC  
7
8
9
Not Used  
Not Used  
Dome Power  
P104  
P104  
P101  
AWG 18-14  
AWG 18-14  
3
2
1
2
1
Dome 24 VAC  
Earth Ground  
Dome 24 VAC  
Heater 24 VAC  
Heater 24 VAC  
10  
Heater Power  
P107  
J101  
11  
12  
RJ45 Ethernet Video and Control  
To AutoDome  
3.7.1  
Connecting Wires to the Pipe Interface Board  
The Pipe Interface Board contains all of the connectors for control, data, image, and power  
wires. Follow the procedures below to make the proper connections.  
WARNING!  
Use a 24 VAC Class 2 power supply only.  
1. Attach an RJ45 connector plug to the Ethernet cable and connect the plug to its mating  
connector J101 on the Pipe Interface Board.  
2. Attach the control data in/out wires to their respective terminals on the P105 connector  
on the Pipe Interface Board. See Figure 3.10, Page 46, for an illustration of these  
connections.  
3. Connect the 24 VAC power wires to the P101 connector on the Pipe Interface Board. If  
this model has a heater, connect the 24 VAC heater power wires to connector P107.  
CAUTION!  
To protect the AutoDome from damage due to cold temperatures, ensure that you connect the  
24 VAC heater power wires to the P101 connector.  
4. To connect alarm inputs and outputs, attach the supplied 6-pin Alarms In and the 4-pin  
Alarms Out connector plugs with flying leads to the appropriate alarm wires. Then  
connect the plugs to their mating connectors P103 and P102 on the Pipe Interface Board.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
48 en | Installing Roof Parapet and Pipe Mounts  
AutoDome 800 Series HD PTZ Camera  
WIRE  
1
2
3
4
WHITE  
BROWN  
ORANGE  
GREEN  
WIRE  
WHITE  
1
2
3
4
5
6
BROWN  
ORANGE  
GREEN  
YELLOW  
BLUE  
Figure 3.11 Alarm and Relay Connector Plugs  
1
4-pin Alarm Output Flying Lead  
2
6-pin Alarm Input Flying Lead  
Wire Color  
Description  
Not used  
Not used  
Relay Out 1  
Relay Ground  
Wire Color Description  
1
2
3
4
White  
1
2
3
4
5
6
White  
Brown  
Orange  
Green  
Yellow  
Blue  
Alarm Input 1 (A3)  
Alarm Input 2 (A4)  
Not used  
Not used  
Not used  
Brown  
Orange  
Green  
Alarm Ground (AGND)  
Note: There is a slot located at the top of the Interface Board to tie the wires to the circuit  
board with a cable tie.  
5. Insert the Pipe Interface Board into the down pipe and fasten the three (3) retaining  
screws to secure the board to the Dome Cap.  
CAUTION!  
Be careful not to strip the threads when tightening the Pipe Interface Board retaining screws.  
Figure 3.12 Pipe Interface Board to Dome Cap Assembly  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Installing Roof Parapet and Pipe Mounts | en  
49  
1
2
3
Interface Board  
Retaining Screws (3)  
Pendant Mounting Screws (2)  
3.8  
Attach Pendant to Pipe and Tighten  
CAUTION!  
The bubble is packaged with a protective plastic sheet. It is recommended that the bubble  
remain stored this way until it is ready to install. Limit handling the bubble, as any scratches  
can quickly affect visibility.  
1. Before attaching the Pendant, visually inspect the Pendant dome and the Interface Board  
connectors for any blocked pin holes and bent pins.  
2. Tilt the Pendant enough to place its mounting hook on top of the its housing, over the  
recessed hinge pin of the Dome Cap.  
a
b
c
Figure 3.13 Pendant to Roof / Pipe Mount Attachment  
1
2
Tilt Dome.  
Hook and drop.  
2a Dome Cap  
2b Recessed Hinge Pin  
2c Dome Connector  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
50 en | Installing Roof Parapet and Pipe Mounts  
AutoDome 800 Series HD PTZ Camera  
3
4
Rotate down to engage dome connector.  
Tighten the two (2) mounting screws to a minimum torque of 10-12 N-m (90-105 in.-lbs).  
3. Drop the Pendant down slightly to engage the dome hook and hinge pin of the Dome  
Cap, allowing the dome to rotate around the hinge pin.  
4. Rotate the dome housing down to a vertical position and gently push upward to engage  
the connector on top of the dome housing.  
CAUTION!  
If you feel any resistance when rotating the dome housing or when engaging the connector,  
stop immediately and start over.  
5. Hold the housing firmly in position and alternately tighten the two (2) 5-mm Allen head  
mounting screws from above to a torque value of 10-12 N-m (90-105 in.-lbs).  
CAUTION!  
You must tighten the two mounting screws to a minimum torque of 10-12 N-m (90-105 in.-lbs)  
to ensure a proper seal between the arm and the housing.  
6. Rotate the arm to swing the AutoDome out from the roof and into position, if installing a  
Parapet Roof Mount.  
7. Tighten the three (3) 10-mm (3/8-inch) stainless steel hex bolts on the bracket to lock  
the Parapet Arm in position. See Figure 3.13, Page 49, for an illustration.  
CAUTION!  
Do not over tighten the bolts. The maximum torque is 34 N-m (25 ft-lb).  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Cable and Wire Standards | en  
51  
4
Cable and Wire Standards  
4.1  
Power  
115/230 VAC  
Copper Wire  
To comply with local codes.  
4.2  
4.3  
Wire Distance Guide for Pendant  
24 V to AutoDome  
VA / Watts 14 AWG (2.5 mm) 16 AWG (1.5 mm) 18 AWG (1.0 mm)  
800 Series with IVA, Outdoor 60 / 55  
58 m (190 ft)  
36 m (119 ft)  
23 m (75 ft)  
Table 4.1 Maximum Wire Distances from Power Supply to AutoDome  
Video and Control Cables  
Ethernet  
The AutoDome 800 Series models are connected to a 10/100 Base-T network either directly or  
via a hub. Both video and control are transmitted over a standard TCP/IP network using the  
built-in web server.  
CAUTION!  
Ethernet connections must be made to non-exposed (indoor) networks only.  
Cable Type  
UTP CAT-5  
100 m (328 ft)  
10/100 Base-T  
RJ45  
Maximum Distance  
Bandwidth  
Terminal Connector  
Fiber Optic Ethernet Media Converter  
The fiber optic media converter is designed to transmit 10/100 Mbps Ethernet signals over  
fiber optic cable using 10/100 Mbps Small Form-factor Pluggable (SFP) modules. The SFP  
modules are available as multi-mode fiber (MMF) or single-mode fiber (SMF) models with a  
single SC connector or dual-fiber with an LC connector. Refer to the VG4-SFPSCKT Fiber Optic  
Media Converter Installation Guide.  
Ethernet Media Converter  
Data Interface  
Data Rate  
Ethernet  
10/100 Mbps  
IEEE 802.3 Compliant  
Full Duplex or Half Duplex Electrical Port  
Full Duplex Optical Port  
Fiber Type, MMF  
50/125 µm MMF. For 50/125 µm fiber, subtract 4 dB from the  
specified optical budget value. Must meet or exceed fiber standard  
ITU-T G.651.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
52 en | Cable and Wire Standards  
AutoDome 800 Series HD PTZ Camera  
Ethernet Media Converter  
Fiber Type, SMF  
8–10/125 µm SMF. Must meet or exceed fiber standard ITU-T  
G.652.  
Maximum Distance  
Requirement  
20 km (12.4 miles)  
Media converter receiver (CNFE2MC/IN) at controller end of  
system  
Terminal Connection  
Duplex LC or Single SC  
4.4  
Audio Cables  
The AutoDome 800 Series is capable of receiving line input audio signals and transmitting it  
over a network. The audio signal is transmitted one-way and in sync with the video signals.  
Audio Line Input Specifications  
Max. Input Voltage  
Impedance  
5.5 Vpp  
9K ohm  
Sample Rate  
Shield  
8 K Hz, 16 Bit, mono  
Bare copper braid: 95% coverage  
Internal gain level adjustment is available  
Wire Specifications  
Wire Type  
Distance  
Gage  
Coax (recommended)  
10 m (33 ft)  
22 AWG to connector (P105/P106)  
Bare copper braid: 95% coverage  
Stranded bare copper  
Shield  
Center conductor  
NOTICE! Separate the audio cables from the AC power lines to avoid noise.  
Audio Connections  
1. Remove the 100 Ohm termination resistor from the terminals.  
2. Connect the audio line level source to the Audio+ (C+) input terminal.  
3. Connect the audio signal ground to the Audio- (C-) input terminal.  
The following figure illustrates the connections for audio over an IP network.  
Figure 4.1 Connections for audio over an Ethernet network  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Cable and Wire Standards | en  
53  
1
2
3
4
5
6
Audio- (C-)  
7
8
9
AutoDome Data In/Out  
P105/P106 Connector  
Audio Out  
Audio+ (C+)  
Earth Ground  
RxD  
TxD  
Signal Ground  
NOTICE! See Section 7.30 Audio, page 90 for audio configuration.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
54 en | Alarms and Relay Connections  
AutoDome 800 Series HD PTZ Camera  
5
Alarms and Relay Connections  
5.1  
Alarm Inputs  
The AutoDome provides two alarm inputs. Each input can be activated by dry contact devices  
such as pressure pads, passive infrared detectors, door contacts, and similar devices. The  
table below summarizes the size and distance wires.  
Wire Size  
Maximum Distance  
AWG mm  
feet  
500  
800  
meters  
152.4  
243.8  
22  
18  
0.644  
1.024  
Table 5.1 Alarm wire guide  
You wire alarms either Normally Open (N.O.) or Normally Closed (N.C.), and must program the  
alarm inputs N.O. (the default) or N.C. through the Settings page (refer to Section 7.39 Alarm  
Connections, page 95).  
5.2  
Connecting Alarms (inputs 1 or 2)  
You can configure alarms 1 and 2 as non-supervised Normally Open (N.O.) or Normally Closed  
(N.C.) alarms.  
5.2.1  
Connecting a Normally Open Alarm  
1. Connect the alarm to the appropriate input (1 or 2) and ground at the AutoDome.  
Figure 5.1 N.O. - Normally Open Non-supervised Connections  
1
2
Dry Contact  
Alarm Inputs 1 to 2  
3
4
Dome Connector  
Ground  
2. From the Alarm Connections page on the Settings Page (Section 7.39 Alarm Connections,  
page 95) the Alarm Input # to N.O. See the table below for contact and condition details.  
AutoDome Programmed N.O.  
Circuit  
Open  
Alarm Indication  
Normal  
Closed  
Alarm  
5.2.2  
Connecting a Normally Closed Alarm  
1. Connect the alarm to the appropriate input (1 or 2) and ground at the AutoDome.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Alarms and Relay Connections | en  
55  
Figure 5.2 N.C. Normally Closed Non-supervised Connections  
1
2
Dry Contact  
Alarm Inputs 1 to 2  
3
4
Dome Connector  
Ground  
2. From the Alarm Connections page on the Settings Page (Section 7.39 Alarm Connections,  
page 95) the Alarm Input # to N.C. See the table below for contact and condition details.  
AutoDome Programmed N.C.  
Circuit  
Open  
Alarm Indication  
Alarm  
Closed  
Normal  
5.3  
Configuring an Open Collector Output  
The AutoDome incorporates one (1) open collector output.  
This output must be connected to a positive voltage between 5 and 32 V to complete the  
circuit, with a maximum voltage rating of 32 VDC @ 150 ma.  
1. Connect the appropriate stripped wire to the open connector (1, 2, or 3) of the  
transistor.  
2. Connect the appropriate stripped wire to the ground (GND) connector.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
56 en | Using the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
6
Using the AutoDome 800 Series  
The AutoDome 800 Series transmits PTZ control commands and images over a TCP/IP  
network. It also allows users to configure the camera display settings, camera operating  
settings, and to configure the network parameters.  
The IP unit incorporates a network video server in the IP module. The primary function of the  
server is to encode video and control data for transmission over a TCP/IP network. With its  
H.264 encoding, it is ideally suited for IP communication and for remote access to digital  
video recorders and multiplexers. The use of existing networks means that integration with  
CCTV systems or local networks can be achieved quickly and easily. Video images from a  
single camera can be simultaneously received on several receivers.  
Refer to Section 9 BVIP Firmware Updates, page 115, for firmware upgrade instructions.  
6.1  
Overview of Features  
The AutoDome 800 Series includes the following functionality:  
Function  
Description  
Video Encoding  
The camera uses the H.264 compression standards and ensures that the  
data rate remains low even with high image quality and can also be  
adapted to local conditions within wide limits.  
Streaming  
Encodes multiple data streams simultaneously according to individually  
customized profiles. This feature creates data streams that can serve  
different purposes. For example, one (1) data stream for recording and  
one (1) data stream optimized for transmission over the Local Area  
Network (LAN).  
Multicast  
Enables simultaneous, real-time transmission to multiple receivers. The  
network must implement the UDP and IGMP V2 protocols as a  
prerequisite for Multicasting.  
Configuration  
Allows configuration for all camera settings from a Web browser on the  
local network (Intranet) or on the Internet. You can also update the  
firmware, load device configurations, store configuration settings, and  
copy these settings from one camera to another.  
Snapshots  
Record  
Allows you to take and store individual video frames as JPEG images from  
the Web browser interface.  
Allows configuration for the recording options of the IP module. You can  
record video from the Livepage to a hard drive or you can opt to store up  
to 8 MB of video on the IP module.  
6.2  
System Requirements  
The AutoDome 800 Series requires specific software and hardware to allow a user to view live  
images and to configure camera settings over a TCP/IP network. These requirements are:  
–
–
A computer with the Microsoft Windows XP, Vista, or Windows 7 operating system,  
network access, and the Microsoft Internet Explorer Web browser version 7.0 or later, or  
A computer with Microsoft Windows XP, Vista, or Windows 7 operating system, network  
access, and reception software such as the Bosch Video Management System or a Bosch  
recording solution, or  
–
A compatible hardware decoder from Bosch Security Systems as a receiver and a  
connected video monitor.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Using the AutoDome 800 Series | en  
57  
NOTICE!  
The Web browser must be configured to enable Cookies to be set from the IP address of the  
unit.  
In Windows Vista, deactivate protected mode on the Security tab under Internet Options.  
You can find notes on using Microsoft Internet Explorer in the online Help in Internet Explorer.  
If you choose to use a computer running Microsoft Internet Explorer or any of the Bosch  
software, the computer must conform to the following minimum requirements:  
–
Operating System: Windows XP (Service Pack 3), Windows Vista or Windows 7 (32 or 64  
bits)  
–
–
–
–
–
–
Processor: Intel Pentium Quad Core, 3.0 GHz or comparable  
RAM: 2048 MB  
Free Hard Disk Space: 10 GB  
Video system: NVIDIA GeForce 8600 or higher display with a minimum of 16-bit color  
Network interface: 100/1000-BaseT  
Software:  
–
–
–
–
–
Microsoft Internet Explorer, version 7.0 or higher  
Bosch Video Client (BVC)  
DirectX 9.0c  
MPEG-ActiveX 5.20.0045 or newer  
Oracle Java Virtual Machine 1.6.0_26  
NOTICE!  
The Web browser must be configured to enable Cookies to be set from the IP address of the  
unit.In Windows 7, deactivate protected mode on the Security tab under Internet Options. You  
can find notes on using Microsoft Internet Explorer in the online Help in Internet Explorer.  
For the latest versions of the Bosch Video Client, DirectX, ActiveX, and the Oracle Java Virtual  
Machine software, go to www.boschsecurity.com, then navigate to the AutoDome 800 Series  
product page and download the software from the Software tab.  
NOTICE!  
Ensure the graphics card is set to 16-bit or 32-bit color. If you need further assistance, contact  
your PC system administrator.  
6.3  
Connecting the AutoDome 800 Series to the PC  
1. Install the AutoDome 800 Series according to the instructions in this manual.  
2. Connect an Ethernet cable from the AutoDome 800 Series RJ45 connector to a dedicated  
network switch to bypass the Local Area Network (LAN).  
3. Connect the dedicated network switch to the RJ45 connector on the PC (see option A  
below).  
NOTICE!  
The AutoDome 800 Series can also be connected directly to a PC using an Ethernet crossover  
cable with RJ45 connectors (see option B below).  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
58 en | Using the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
Figure 6.1 AutoDome 800 Series System Configuration  
1
2
3
4
AutoDome 800 Series  
IP Connection  
Network Switch  
Computer  
NOTICE!  
You can also use the Bosch Configuration Manager utility to configure the network settings for  
an AutoDome 800 Series camera. Go to www.boschsecurity.com to download the  
Configuration Manager software (part of the BVIP Lite Suite) and Operating Manual.  
6.4  
Configuring the AutoDome 800 Series Camera  
To operate the camera in your network you must assign it a valid network IP address. The  
default IP address is 192.168.0.1, but you may have to change this address if it conflicts with  
another device on your network. Refer to Section 7.3 Basic Mode: Network, page 72 for more  
information.  
To properly configure the camera for your network, you need the following information:  
–
Unit IP address: An identifier for the camera on a TCP/IP network. For example,  
140.10.2.110 is a valid syntax for an IP address.  
–
–
–
Subnet mask: A mask used to determine what subnet an IP address belongs to.  
Gateway IP address: A node on a network that serves as an entrance to another network.  
Port: An endpoint to a logical connection in TCP/IP and UDP networks. The port number  
identifies the use of the port for use through a firewall connection.  
NOTICE!  
Ensure that the network parameters of your cameras are available before you begin  
configuration.  
The AutoDome 800 Series defaults are as follows:  
–
–
–
IP Address: 192.168.0.1  
Subnet Mask: 255.255.255.0  
Gateway IP Address: 0.0.0.0  
The following sections provide instructions about installing the software necessary to view  
images over an IP connection, configuring the IP network settings and accessing the  
AutoDome 800 Series images from a Web browser.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Using the AutoDome 800 Series | en  
59  
6.4.1  
Changing the Network Settings  
The AutoDome 800 Series has a default IP address of 192.168.0.1. To change the IP address  
or any network settings, you can use the Configuration Manager software or the AutoDome  
800 Series server.  
NOTICE!  
Contact your local network administrator for a valid IP address, Subnet Mask, and a Gateway  
IP Address.  
Using the Configuration Manager  
Configuration Manager is an optional network utility provided on the Bosch Security Systems  
Web site. Use the Configuration Manager Manual to make any configuration changes.  
NOTICE!  
Depending on the PC network security settings, the user may have to add the new IP address  
to the browser’s trusted sites list for the IP AutoDome controls to operate.  
Using the AutoDome 800 Series Web Server  
To configure the camera using the AutoDome 800 Series server, do the following:  
1. Set the IP address on the PC to 192.168.0.10to ensure that the PC and the AutoDome  
800 Series are on the same Subnet.  
2. Launch Microsoft Internet Explorer and navigate to the following URL: http://192.168.0.1  
The Web browser opens the Livepage for the AutoDome 800 Series; a security warning  
message is displayed.  
3. Check the Always Trustbox, then click YES.  
4. Click the Settings link, located at the top of the Livepage.  
5. Click the Service Settings link, located in the left pane of the Settings window.  
6. Click the Network link to open the Network Settings page.  
Figure 6.2 Network Settings Page  
7. Configure the settings on this page based on the addresses provided by your local  
network administrator.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
60 en | Using the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
NOTICE!  
Click the Help on this page? link if you need more information.  
8. Click the Set button to save the settings.  
9. Launch another instance of Microsoft Internet Explorer.  
10. Type the original IP address followed by /reset (for example, http://192.168.0.1/reset) in  
the address bar and click Go to restart the AutoDome 800 Series. Once you restart the  
AutoDome 800 Series, use the new IP Address to access the Livepage.  
11. Disconnect the AutoDome 800 Series Ethernet cable from the dedicated network switch  
and reconnect the Ethernet cable to the local area network (LAN).  
6.5  
Configuring Intelligent Tracking  
The AutoDome utilizes the built-in Intelligent Video Analytics (IVA) to continuously follow an  
individual or object even if it passes behind a Privacy Mask or a stationary object. The  
AutoDome uses objects detected by IVA in a stationary preset position to activate the  
Intelligent Tracking feature. Intelligent Tracking controls the pan/tilt/zoom actions of the  
camera to keep the selected object in the scene.  
To activate the Intelligent Tracking feature, one of the following conditions must be met:  
–
–
The Silent IVA option must be selected in the VCA page on the Settings tab. Refer to  
Section 7.40 VCA, page 97.  
IVA must be active for at least one preset scene in the VCA page on the Settings tab. If  
IVA is configured for one scene, then all other scenes have Intelligent Tracking enabled by  
default. If a scene, however, has Motion+ of IVA Flow activated then the Intelligent  
Tracker is disabled for these scenes.  
NOTICE!  
The following actions occur if Intelligent Tracking is active:  
–
–
All other IVA objects are disabled in scenes with Intelligent Tracking.  
The camera automatically disables the display of compass headings. Refer to Page 88 for  
details of the Compass feature.  
6.5.1  
Intelligent Tracking Operation  
The Intelligent Tracking feature behaves in one of the following ways:  
–
A user controls the pan/tilt/zoom while the AutoDome is in Intelligent Tracking mode.  
User actions always take precedence over Intelligent Tracking. If the AutoDome is actively  
tracking an object and a user takes control, the AutoDome will attempt to track the  
object after a period of inactivity.  
–
An IVA alarm can trigger Intelligent Tracking to track a detected object.  
A rule that triggers an IVA event must be set. The following standard tasks can be set  
Object in field, Crossing Line, Loitering, Condition change, Following route, Entering  
field, and Leaving field. Refer to the Intelligent Video Analysis Operation Guide for  
complete details about using IVA.  
–
A user manually selects an object in the live image area to track.  
Intelligent Tracking allows a user to click a moving object in the live image display inside  
the Livepage to identify an object to track.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Using the AutoDome 800 Series | en  
61  
6.5.2  
Guidelines for Implementing Intelligent Tracking  
Factors such as the viewing angle and unwanted motion (from trees, for example) may  
interfere with Intelligent Tracking operation. Use the following recommendations to ensure  
smooth Intelligent Tracking operation:  
–
–
–
Mount/Mounting Surface Stability  
–
Mount the camera in the most stable position. Avoid locations affected by vibrations,  
such as those caused by a roof-top air conditioner. These vibrations may cause  
complications when the camera zooms-in on a target.  
–
–
Use the pendant arm mount, if possible. This mount option provides the most  
stability for the camera.  
Use guy wires to protect against strong winds if using the parapet mount.  
Field of View  
–
Select a location and viewing angle that allows the flow of people to move across  
the camera’s field of view.  
–
–
Avoid motion that moves directly towards the camera.  
Avoid locations that attract large numbers of people, such as retail stores or  
intersections. Intelligent Tracking is optimized for scenes with very few moving  
objects.  
Unwanted Motion  
Avoid neon lights, flashing lights, night time lights, and reflected light (from a  
–
window or mirror, for example). The flickering of these lights can affect the  
Intelligent Tracking operation.  
6.6  
The Livepage  
Once the connection is established, the Web browser displays the Livepage. It shows the live  
video image on the right of the browser window. Depending on the configuration, various text  
overlays may be visible on the live video image.  
Other information may be shown next to live video image on the Livepage. The display  
depends on the settings on the Livepage Configuration page (see the AutoDome 800 Series  
online help).  
Display Stamping  
Various overlays or “stamps” in the video image provide important status information. The  
overlays provide the following information:  
Decoding error. The frame might show artefacts due to decoding errors. If subsequent  
frames reference this corrupted frame, they might also show decoding errors as well  
but won’t be marked with the “decoding error” icon.  
Alarm flag set on media item  
Communication error. Any kind of communication error is visualized by this icon.  
Cause can be a connection failure to the storage medium, a protocol violation with a  
sub component or simply a timeout. An automatic reconnection procedure is started  
in the background in order to recover from this error.  
Gap; no video recorded  
Watermarking not valid  
Watermarking flag set on media item  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
62 en | Using the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
Motion flag set on media item  
Discovery of storage not completed. If the information about recorded video is not  
cached, a discovery procedure is started in order find all recorded video. During this  
time, the “discovery” symbol is shown. While discovery is executed, gaps might be  
shown in places which the discovery has not yet reached. The gap will automatically  
be replaced by the true video, as soon as the correct information is available.  
Maximum Number of Connections  
If you do not connect, the unit may have reached its maximum number of connections.  
Depending on the unit and network configuration, each AutoDome 800 Series can have up to  
25 Web browser connections or up to 50 connections via the Bosch Video Management  
System.  
Protected AutoDome 800 Series  
If the AutoDome 800 Series is password protected against unauthorized access, the Web  
browser displays a corresponding message and prompts you to enter the password when you  
attempt to access protected areas.  
NOTICE!  
An AutoDome 800 Series offers the option to limit the extent of access using various  
authorization levels (see the AutoDome 800 Series online help).  
1. Enter the user name and associated password in the corresponding text fields.  
2. Click OK. If the password is entered correctly, the Web browser displays the page that  
was called up.  
Protected Network  
If a RADIUS server is employed in the network for managing access rights (802.1x  
authentication), the AutoDome 800 Series must be configured accordingly, otherwise no  
communication is possible.  
Image Selection  
You can view the image of the camera in different displays.  
Click one of the tabs Stream 1, Stream 2, or M-JPEG below the video image to toggle  
between the different displays of the camera image. To display an I-frame only stream,  
refer to Section 7.15 Livepage Functions, page 78.  
View Control  
The View Control tab allows you to control camera functions (pan, tilt, zoom, focus, and iris),  
navigate through on-screen menus and to view preset shots.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Using the AutoDome 800 Series | en  
63  
Reference # Description  
Reference # Description  
Focus far2  
Focus near2  
Iris close2  
Iris open2  
1
2
3
4
5
Tilts the camera up  
8
Tilts the camera down  
Pans the camera to the left  
Pans the camera to the right  
9
10  
11  
Pans and tilts the camera in all directions 12  
Sets the PTZ speed for controls 1, 2, 3,  
4, 5, 6, and 7  
Zoom out1  
Zoom in1  
6
13  
Moves the camera to pre-set shot  
numbers 1, 2, 3, 4, 5, and 6  
7
1. This function is also accessible by using the mouse scroll wheel while in the Live video frame.  
2. This button is also used as the "Enter" button to select menu items from the AUX tab.  
1. To control a peripheral, click the appropriate controls.  
2. Move the mouse cursor over the video image. Additional options for controlling  
peripherals are displayed with the mouse cursor.  
3. To manually pan throughout the image area, move your cursor over any part of the live  
video. The image area displays a directional arrow (  
right mouse key to pan the camera.  
), then click and hold the  
Digital I/O  
The alarm icon is for information purposes and indicates the status of an alarm input: When  
an alarm is triggered, the icon lights up blue. The device’s configuration determines whether  
the alarm is displayed, as well as additional details (see the AutoDome 800 Series online  
help).  
Triggering Relay  
You can switch connected units using the relays in the AutoDome 800 Series (for example  
lights or door openers).  
To activate this, click the icon for the relay next to the video image. The icon will be red  
when the relay is activated.  
System Log / Event Log  
The System Log field contains information about the operating status of the AutoDome 800  
Series and the connection. You can save these messages automatically in a file (see the  
AutoDome online help).  
Events such as the triggering or end of alarms are shown in the Event Log field. You can save  
these messages automatically in a file (see the AutoDome online help).  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
64 en | Using the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
1. If you want to delete the entries, click the delete icon in the top right-hand corner of the  
relevant field.  
2. If you want to view a detailed log, click the icon in the top right-hand corner of the  
relevant field. A new window will open.  
6.6.1  
Entering a Keyboard Control Command  
The Aux Control tab is used to enter keyboard control commands. These commands are  
composed of a command number plus the appropriate function key (Show Shot, Set Shot Aux  
On or Aux Off). A valid combination either issues a command to the camera or displays an on-  
screen menu.  
Aux Control Tab  
The Aux Control tab is used to enter pre-programmed keyboard control commands.  
See Section A Keyboard Commands by Number, page 116, for a list of all commands.  
To access the Aux Control tab, navigate to the Livepage and click the Aux Control tab (see  
Figure 6.3 below).  
Figure 6.3 Aux Control Tab  
1
2
3
4
5
6
7
8
Command number field  
Keypad (numbers 0-9)  
Show a preset shot  
Set a preset shot  
Initiates a command  
Deletes a number in the Command Number field  
Used to select a menu item  
Stops a command  
To Enter a Keyboard Control Command:  
1. Place the cursor in the Command Number field.  
2. Click the desired command number via the on-screen keypad.  
3. Click either the Aux On or the Aux Off button to initiate or stop the command.  
4. If the command initiates a menu, use the Up/Down arrows on the View Control to  
navigate the menu. Click the Focus or Iris button to select a menu item.  
To Set a Preset Shot:  
Preset shots (or scenes) are camera positions that are saved in memory for future use.  
1. Move your cursor over the live image and wait for the area to display a directional arrow.  
2. Click and hold a mouse button to pan to the desired position you want to save.  
3. Click any number combination from 1-99 from the on-screen keypad to identify the scene  
number.  
4. Click the Set Shot button. The image area displays a message that indicates which shot  
number was saved.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Using the AutoDome 800 Series | en  
65  
To View a Preset Shot:  
1. Click the number of the scene you want to view using the on-screen keypad.  
2. Click the Show Shot button.  
NOTICE!  
For more information about the AutoDome 800 Series settings and controls, click the Help on  
this page? link to open the AutoDome 800 Series online help.  
6.6.2  
Using Intelligent Tracking  
Intelligent Tracking continuously follows an individual or an object. Intelligent Tracking  
operates by recognizing an object in motion and zooms-in to approximately 50% of the field of  
view for an average target height of six feet. Refer to Section 6.5 Configuring Intelligent  
Tracking, page 60, for details about activating the Intelligent Tracking feature.  
Note: If you do not see these controls on the Livepage, ensure that the Enable AutoTrack  
option is selected on the Livepage Functions page in the Settings tab. Refer to  
Section 7.15 Livepage Functions, page 78.  
Use the following options to control Intelligent Tracking:  
–
–
–
Off: Disables Intelligent Tracking.  
Auto: Enables Intelligent Tracking. Constantly monitors for and actively tracks motion.  
Click: Click on a moving target in the live video image to enable the AutoDome to track  
the movement of the selected target.  
NOTICE!  
When Intelligent Tracking is activated, the AutoDome disables the display of the compass  
heading. Once Intelligent Tracking is set to Off, the AutoDome resumes display of the  
compass heading. Refer to Page 88 for details of the Compass feature.  
If the Intelligent Tracking feature is set to Auto or Click, the live video image displays an eye  
icon in a color that conveys the state of the Intelligent Tracking:  
–
White: SEEK mode  
Intelligent Tracking is actively seeking a target to follow.  
–
Pink: IDLE mode  
Intelligent Tracking lost the selected target and will wait for the target to reappear using  
the last known trajectory.  
–
–
Black: ACTIVE mode  
Intelligent Tracking is actively tracking a target.  
Yellow: PASSIVE mode  
Intelligent Tracking attempts to passively track a target while a user has camera control.  
Several reasons may cause the Intelligent Tracking to stop tracking a target:  
–
–
The target has stopped moving while being followed by Intelligent Tracking.  
The target has moved behind a static object in the scene.  
In these instances Intelligent Tracking switches to the IDLE mode (pink eye icon) and waits  
for the target to reappear in the scene. The camera will restart tracking if a target starts  
moving in the same area where the initial target stopped moving or if the camera detects an  
object moving along the last known trajectory.  
6.6.3  
Using Special Functions  
The AutoDome offers several special command buttons on the Livepage.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
66 en | Using the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
Scan 360  
Click this button to start a continuous 360° pan. To stop the continuos pan, click a directional  
control in the View Control tab.  
Autopan  
Click this button to pan the AutoDome between user-defined limits. To set the left and right  
pan limits, refer to Section 7.24 PTZ Settings, page 87, so set the Autopan limits. To stop the  
continuos pan, click a directional control in the View Control tab.  
Tour A / Tour B  
Click one of these buttons to start the playback of a recorded (guard) tour. A Recorded Tour  
saves all manual camera movements made during the recording, including its rate of pan, tilt  
and zoom speeds and other lens setting changes. Refer to Section 7.24 PTZ Settings, page 87,  
to program a recorded tour. To stop a tour, click a directional control in the View Control tab.  
6.7  
6.8  
Saving Snapshots  
You can save individual images from the video sequence currently shown on the Livepage in  
JPEG format on your computer's hard drive. The icon for recording single images is only  
visible if the unit is configured to enable this process.  
Click the icon. The storage location depends on the configuration of the AutoDome 800  
Series.  
Recording Video Sequences  
You can save sections of the video sequence currently shown on the Livepage on your  
computer's hard drive. The icon for recording video sequences is only visible if the unit is  
configured to enable this process.  
1. Click the icon to start recording. The storage location depends on the configuration of  
the AutoDome 800 Series. A red dot in the icon indicates that recording is in progress.  
2. Click the icon again to stop recording.  
3. To change the storage location for the recorded video, navigate to the Livepage settings  
on the Settings page.  
Image Resolution  
Sequences are saved at the resolution that has been preset in the configuration for the  
encoder (see Section 7.3 Basic Mode: Network, page 72).  
6.9  
Processor Load  
If the AutoDome 800 Series is accessed via the Web browser, you will see the processor load  
indicator in the top left of the window next to the manufacturer's logo.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Using the AutoDome 800 Series | en  
67  
You can obtain additional information to help when you troubleshoot or fine-tune the unit. The  
values indicate the proportions of the individual functions on the encoder load, shown as  
percentages.  
Move the cursor over the graphic indicator. Some additional numerical values are also  
displayed.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
68 en | Using the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
6.10  
Recordings page  
Click Recordings to access the Recordings page from the Livepage or Settings page (the  
Recordings link is only visible if a storage medium has been selected).  
Selecting Recordings  
All saved sequences are displayed in a list. A track number is assigned to each sequence. Start  
time and stop time, recording duration, number of alarms, and recording type are displayed.  
To play back recorded video sequences:  
1. Select Recording 1 or 2 in the drop-down menu. (The contents for 1 and 2 are identical,  
only the quality and location may be different.)  
2. Use the arrow buttons to browse the list.  
3. Click a track. The playback for the selected sequence starts.  
Export to FTP  
Click Export to FTP to send the current track to the FTP server. If required, change the times  
within the selected range.  
6.10.1  
Controlling playback  
A time bar below the video image allows quick orientation. The time interval associated with  
the sequence is displayed in the bar in gray. A green arrow above the bar indicates the  
position of the image currently being played back within the sequence.  
The time bar offers various options for navigation in and between sequences.  
–
Change the time interval displayed by clicking the plus or minus icons. The display can  
span a range from two months to a few seconds.  
–
–
If required, drag the green arrow to the point in time at which the playback should begin.  
Red bars indicate the points in time where alarms were triggered. Drag the green arrow  
to navigate to these points quickly.  
Control playback by means of the buttons below the video image. The buttons have the  
following functions:  
Start/Pause playback  
Jump to start of active sequence or to previous sequence  
Jump to start of the next video sequence in the list  
Slide control  
Continuously select playback speed by means of the speed regulator:  
Bookmarks  
In addition, set markers in the sequences, so-called bookmarks, and jump directly to these.  
These bookmarks are indicated as small yellow arrows above the time interval. Use the  
bookmarks as follows:  
Jump to the previous bookmark  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Using the AutoDome 800 Series | en  
69  
Set bookmark  
Jump to the following bookmark  
Bookmarks are only valid while in the Recordings page; they are not saved with the  
sequences. All bookmarks are deleted when leaving the page.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
70 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
7
Configuring the AutoDome 800 Series  
The SETTINGS page provides access to the configuration menu, which contains all the unit's  
parameters arranged in groups. You can view the current settings by opening one of the  
configuration screens. You can change the settings by entering new values or by selecting a  
predefined value from a list field.  
There are two options for configuring the unit or checking the current settings:  
–
–
Basic mode  
Advanced mode  
In Basic Mode the most important parameters are arranged in seven groups. This allows you  
to change the basic settings with just a few entries and then put the device into operation.  
Advanced Mode is recommended for expert users or system support personnel. You can  
access all unit parameters in this mode. Settings that affect the fundamental functionality of  
the unit (such as firmware updates) can only be altered in the advanced mode.  
All parameter groups are described in this chapter in the order in which they are listed in the  
configuration menu, from the top of the screen to the bottom.  
CAUTION!  
The settings in the advanced mode should only be processed or modified by expert users or  
system support personnel.  
All settings are backed up in the AutoDome 800 Series memory so they are not lost even if the  
power fails.  
Starting Configuration  
Click the SETTINGS link in the upper section of the window. The Web browser opens a  
new page with the configuration menu.  
Navigation  
1. Click one of the menu items in the left window margin. The corresponding submenu is  
displayed.  
2. Click one of the entries in the submenu. The Web browser opens the corresponding  
page.  
Making Changes  
Each configuration screen shows the current settings. You can change the settings by entering  
new values or by selecting a predefined value from a list field.  
After each change, click Set to save the change.  
CAUTION!  
Save each change with the associated Set button.  
Clicking the Set button saves the settings only in the current field. Changes in any other fields  
are ignored.  
7.1  
Basic Mode: Device Access  
Camera name  
You can give the AutoDome 800 Series a name to make it easier to identify. The name makes  
the task of administering multiple units in larger video monitoring systems easier, for example  
using the Bosch Video Management System programs.  
The device name is used for the remote identification of a unit, in the event of an alarm for  
example. For this reason, enter a name that makes it as easy as possible to quickly identify the  
location.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
71  
CAUTION!  
Do not use any special characters, for example &, in the name.  
Special characters are not supported by the system's internal recording management and may  
therefore result in the Player or Archive Player being unable to play back the recording.  
Password  
An AutoDome 800 Series is generally protected by a password to prevent unauthorized access  
to the unit. You can use different authorization levels to limit access.  
The AutoDome 800 Series operates with three authorization levels: service, user and live.  
The highest authorization level is service. After entering the correct password, you can access  
all the functions of the AutoDome 800 Series and change all configuration settings.  
With the user authorization level, you can operate the unit and also control cameras, for  
example, but you cannot change the configuration.  
The lowest authorization level is live. It can only be used to view the live video image and  
switch between the different live image displays.  
You can define and change a password for each authorization level if you are logged in as  
service or if the unit is not password protected.  
Enter the password for the appropriate authorization level here.  
NOTICE!  
Proper password protection is only guaranteed when all higher authorization levels are also  
protected with a password. If a live password is assigned, for example, a service and a user  
password must also be set. When assigning passwords, you should therefore always start  
from the highest authorization level, service, and use different passwords.  
Confirm password  
In each case, enter the new password a second time to eliminate typing mistakes.  
NOTICE!  
A new password is only saved when you click the Set button. You should therefore click the  
Set button immediately after entering and confirming a password.  
7.2  
Basic Mode: Date/Time  
Device date/Device time/Device time zone  
If there are multiple devices operating in your system or network, it is important to  
synchronize their internal clocks. For example, it is only possible to identify and correctly  
evaluate simultaneous recordings when all units are operating on the same time. If necessary,  
you can synchronize the unit with your computer's system settings.  
Click the Sync to PC button to copy your computer's system time to the AutoDome 800  
Series.  
Time server IP address  
The AutoDome 800 Series can receive the time signal from a time server using various time  
server protocols, and then use it to set the internal clock. The unit polls the time signal  
automatically once every minute.  
Enter the IP address of a time server here.  
Time server type  
Select the protocol that is supported by the selected time server. Preferably, you should  
select the SNTP server as the protocol. This supports a high level of accuracy and is required  
for special applications and subsequent function extensions.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
72 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
Select Time server for a time server that works with the protocol RFC 868.  
7.3  
Basic Mode: Network  
The settings on this page are used to integrate the AutoDome 800 Series into an existing  
network.  
Some changes only take effect after the unit is rebooted. In this case, the Set button changes  
to Set and Reboot.  
1. Make the desired changes.  
2. Click the Set and Reboot button. The AutoDome 800 Series is rebooted and the changed  
settings are activated.  
CAUTION!  
If you change the IP address, subnet mask or gateway address, the AutoDome 800 Series is  
only available under the new addresses after the reboot.  
DHCP  
If a DHCP server is employed in the network for the dynamic assignment of IP addresses, you  
can activate acceptance of IP addresses automatically assigned to the AutoDome 800 Series.  
Certain applications (VIDOS, Bosch Video Management System, Archive Player, Configuration  
Manager) use the IP address for the unique assignment of the unit. If you use these  
applications, the DHCP server must support the fixed assignment between IP address and  
MAC address, and must be appropriately set up so that, once an IP address is assigned, it is  
retained each time the system is rebooted.  
IP address  
Enter the desired IP address for the AutoDome 800 Series in this field. The IP address must  
be valid for the network.  
Subnet mask  
Enter the appropriate subnet mask for the selected IP address here.  
Gateway address  
If you want the unit to establish a connection to a remote location in a different subnet, enter  
the IP address of the gateway here. Otherwise leave the box blank (0.0.0.0).  
7.4  
Basic Mode: Encoder  
Default profile  
You can select a profile for encoding the video signal.  
You can use this to adapt the video data transmission to the operating environment (for  
example network structure, bandwidth, data load).  
Pre-programmed profiles are available, each giving priority to different perspectives. When  
selecting a profile, details are displayed in the list field.  
–
HD high quality / low latency  
Target bit rate: 5000 kbps  
Maximum bit rate: 10000 kbps  
Encoding interval: 30.00 ips  
–
HD high quality  
Target bit rate: 3500 kbps  
Maximum bit rate: 7000 kbps  
Encoding interval: 30.00 ips  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
73  
–
–
–
–
–
–
HD low bandwidth  
Target bit rate: 2500 kbps  
Maximum bit rate: 5000 kbps  
Encoding interval: 30.00 ips  
SD high quality / low latency  
Target bit rate: 2000 kbps  
Maximum bit rate: 4000 kbps  
Encoding interval: 30.00 ips  
SD high quality  
Target bit rate: 1500 kbps  
Maximum bit rate: 3000 kbps  
Encoding interval: 30.00 ips  
SD low bandwidth  
Target bit rate: 700 kbps  
Maximum bit rate: 1500 kbps  
Encoding interval: 30.00 ips  
DSL  
Target bit rate: 400 kbps  
Maximum bit rate: 500 kbps  
Encoding interval: 30.00 ips  
ISDN (2B)  
Target bit rate: 80 kbps  
Maximum bit rate: 100 kbps  
Encoding interval: 30.00 ips  
7.5  
Basic Mode: Audio  
You can set the gain of the audio signals to suit your specific requirements. The current video  
image is shown in the small window next to the slide controls to help you check the audio  
source and improve assignments. Your changes are effective immediately.  
If you connect via Web browser, you must activate the audio transmission on the Livepagee  
Functions page (see Section 6.6 The Livepage, page 61). For other connections, the  
transmission depends on the audio settings of the respective system.  
Audio  
The audio signals are sent in a separate data stream parallel to the video data, and so increase  
the network load. The audio data are encoded according to G.711 and require an additional  
bandwidth of approx. 80 kbps for each connection. If you do not want any audio data to be  
transmitted, select Off.  
Line In  
You can set the line input gain. Make sure that the display does not go beyond the green zone  
during modulation.  
7.6  
Basic Mode: Recording  
You can record the images from the AutoDome 800 Series on various local storage media or  
on an appropriately configured iSCSI system.  
Here you can select a storage medium and immediately start the recording.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
74 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
Storage medium  
1. Select the required storage medium from the list.  
2. Click the Start button to start the recording immediately.  
7.7  
Basic Mode: System Overview  
The data on this page are for information purposes only and cannot be changed. Keep a  
record of this information in case technical assistance is required.  
NOTICE!  
You can select all required text on this page with the mouse and copy it to the clipboard with  
the [Ctrl]+[C] key combination, for example if you want to send it via e-mail.  
7.8  
7.9  
Advanced Mode: General  
Identification  
Camera ID  
Each AutoDome 800 Series should be assigned a unique identifier that you can enter here as  
an additional means of identification.  
Camera Name  
The camera name makes it easier to identify the remote camera location, in the event of an  
alarm for example. It will be displayed in the video screen if configured to do so. The camera  
name makes the task of administering cameras in larger video monitoring systems easier, for  
example using the VIDOS or Bosch Video Management System programs.  
Enter a unique, unambiguous name for the camera in this field. You can use both lines for this.  
CAUTION!  
Do not use any special characters, for example &, in the name.  
Special characters are not supported by the system's internal recording management and may  
therefore result in the Player or Archive Player being unable to play back the recording.  
You can use the second line for entering additional characters; these can be selected from a  
table.  
1. Click the icon next to the second line. A new window with the character map is opened.  
2. Click the required character. The character is inserted into the Result field.  
3. In the character map, click the << and >> icons to move between the different pages of  
the table, or select a page from the list field.  
4. Click the < icon to the right of the Result field to delete the last character, or click the X  
icon to delete all characters.  
5. Now click the OK button to apply the selected characters to the second line of the  
Camera 1 parameters. The window will close.  
Initiator extension  
You can attach your own text to the initiator name of the AutoDome 800 Series to make the  
unit easier to identify in large iSCSI systems. This text is added to the initiator name,  
separated from it by a full stop. You can see the initiator name in the System Overview page.  
7.10  
Password  
An AutoDome 800 Series is generally protected by a password to prevent unauthorized access  
to the unit. You can use different authorization levels to limit access.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
75  
NOTICE!  
Proper password protection is only guaranteed when all higher authorization levels are also  
protected with a password. If a live password is assigned, for example, a service and a user  
password must also be set. When assigning passwords, you should therefore always start  
from the highest authorization level, service, and use different passwords.  
Password  
The AutoDome 800 Series operates with three authorization levels: service, user and live.  
The highest authorization level is service. After entering the correct password, you can access  
all the functions of the AutoDome 800 Series and change all configuration settings.  
With the user authorization level, you can operate the unit and also control cameras, for  
example, but you cannot change the configuration.  
The lowest authorization level is live. It can only be used to view the live video image and  
switch between the different live image displays.  
You can define and change a password for each authorization level if you are logged in as  
service or if the unit is not password protected.  
Enter the password for the appropriate authorization level here.  
Confirm password  
In each case, enter the new password a second time to eliminate typing mistakes.  
NOTICE!  
A new password is only saved when you click the Set button. You should therefore click the  
Set button immediately after entering and confirming a password.  
7.11  
Date/Time  
Date format  
Select your required date format.  
Device date/Device time  
If there are multiple devices operating in your system or network, it is important to  
synchronize their internal clocks. For example, it is only possible to identify and correctly  
evaluate simultaneous recordings when all units are operating on the same time.  
1. Enter the current date. Since the unit time is controlled by the internal clock, there is no  
need to enter the day of the week – it is added automatically.  
2. Enter the current time or click the Sync to PC button to copy your computer's system  
time to the AutoDome 800 Series.  
Device time zone  
Select the time zone in which your system is located.  
Daylight saving time  
The internal clock can switch automatically between normal and daylight saving time (DST).  
The unit already contains the data for DST switch-overs up to the year 2018. You can use  
these data or create alternative time saving data if required.  
NOTICE!  
If you do not create a table, there will be no automatic switching. When changing and clearing  
individual entries, remember that two entries are usually related to each other and dependent  
on one another (switching to summer time and back to normal time).  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
76 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
1. First check whether the correct time zone is selected. If it is not correct, select the  
appropriate time zone for the system, and click the Set button.  
2. Click the Details button. A new window will open and you will see the empty table.  
3. Select the region or the city that is closest to the system's location from the list field  
below the table.  
4. Click the Generate button to generate data from the database in the unit and enter it into  
the table.  
5. Make changes by clicking an entry in the table. The entry is selected.  
6. Clicking the Delete button will remove the entry from the table.  
7. Select other values from the list fields below the table to change the entry. Changes are  
made immediately.  
8. If there are empty lines at the bottom of the table, for example after deletions, you can  
add new data by marking the row and selecting required values from the list fields.  
9. Now click the OK button to save and activate the table.  
Time server IP address  
The AutoDome 800 Series can receive the time signal from a time server using various time  
server protocols, and then use it to set the internal clock. The unit polls the time signal  
automatically once every minute.  
Enter the IP address of a time server here.  
Time server type  
Select the protocol that is supported by the selected time server. Preferably, you should  
select the SNTP server as the protocol. This supports a high level of accuracy and is required  
for special applications and subsequent function extensions.  
Select Time server for a time server that works with the protocol RFC 868.  
7.12  
Display Stamping  
Various overlays or “stamps” in the video image provide important supplementary  
information. These overlays can be enabled individually and are arranged on the image in a  
clear manner.  
Camera name stamping  
This field sets the position of the camera name overlay. It can be displayed at the Top, at the  
Bottom or at a position of your choice that you can then specify using the Custom option. Or  
it can be set to Off for no overlay information.  
1. Select the desired option from the list.  
2. If you select the Custom option, additional fields are displayed where you can specify the  
exact position (Position (XY)).  
3. In the Position (XY) fields, enter the values for the desired position.  
Time stamping  
This field sets the position of the time overlay. It can be displayed at the Top, at the Bottom or  
at a position of your choice that you can then specify using the Custom option. Or it can be  
set to Off for no overlay information.  
1. Select the desired option from the list.  
2. If you select the Custom option, additional fields are displayed where you can specify the  
exact position (Position (XY)).  
3. In the Position (XY) fields, enter the values for the desired position.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
77  
Display milliseconds  
If necessary, you can also display milliseconds. This information can be useful for recorded  
video images; however, it does increase the processor's computing time. Select Off if you do  
not need to display milliseconds.  
Alarm mode stamping  
Select On to display a text message overlay in the image in the event of an alarm. It can be  
displayed at a position of your choice that you can then specify using the Custom option. Or it  
can be set to Off for no overlay information.  
1. Select the desired option from the list.  
2. If you select the Custom option, additional fields are displayed where you can specify the  
exact position (Position (XY)).  
3. In the Position (XY) fields, enter the values for the desired position.  
Alarm message  
Enter the message to be displayed in the image in the event of an alarm. The maximum text  
length is 31 characters.  
Title OSD  
Select On to continuously display sector or shot title overlays in the image. Select Momentary  
to display sector or shot title overlays for a few seconds. OSD titles can be displayed at a  
position of your choice, or it can be set to Off for no overlay information.  
1. Select the desired option from the list.  
2. Specify the exact position (Position (XY)).  
3. In the Position (XY) fields, enter the values for the desired position.  
Camera OSD  
Select On to momentarily display camera response information, such as Digital Zoom, Iris  
open/close, and Focus near/far overlays in the image. Select Off to display no information.  
1. Select the desired option from the list.  
2. Specify the exact position (Position (XY)).  
3. In the Position (XY) fields, enter the values for the desired position.  
Video watermarking  
Choose On if you wish the transmitted video images to be “watermarked”. After activation, all  
images are marked with a green W. A red W indicates that the sequence (live or saved) has  
been manipulated.  
7.13  
7.14  
Advanced Mode: Web Interface  
Appearance  
On this page you can adapt the appearance of the web interface and change the website  
language to meet your requirements. If necessary, you can replace the manufacturer's logo  
(top right) and the product name (top left) in the top part of the window with individual  
graphics.  
NOTICE!  
You can use either GIF or JPEG images. The file paths must correspond to the access mode  
(for example C:\Images\Logo.gif for access to local files, or http://www.mycompany.com/  
images/logo.gif for access via the Internet/Intranet).  
When accessing via the Internet/Intranet, ensure that a connection is always available to  
display the image. The image file is not stored in the AutoDome 800 Series.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
78 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
Website language  
Select the language for the user interface here.  
Company logo  
Enter the path to a suitable graphic if you want to replace the manufacturer's logo. The image  
file can be stored on a local computer, in the local network or at an Internet address.  
Device logo  
Enter the path to a suitable graphic if you want to replace the product name. The image file  
can be stored on a local computer, in the local network or at an Internet address.  
NOTICE!  
If you want to use the original graphics again, simply delete the entries in the Company logo  
and Device logo fields.  
JPEG interval  
You can specify the interval at which the individual images should be generated for the M-  
JPEG image on the LIVEPAGE.  
7.15  
Livepage Functions  
On this page you can adapt theLivepage functions to your requirements. You can choose from  
a variety of different options for displaying information and controls.  
1. Check the box for the items that are to be made available on the Livepage. The selected  
items are indicated by a check mark.  
2. Check whether the required functions are available on the Livepage.  
Transmit Audio  
You can only select this option if audio transmission is actually switched on (see  
Section 7.30 Audio, page 90).The audio signals are sent in a separate data stream parallel to  
the video data, and so increase the network load. The audio data are encoded according to  
G.711 and require an additional bandwidth of approx. 80 kbps for each connection.  
Lease time (s)  
The lease time in seconds determines the time beyond which a different user is authorized to  
control the camera after no further control signals are received from the current user. After  
this time interval, the camera is automatically enabled.  
Show alarm inputs  
The alarm inputs are displayed next to the video image as icons along with their assigned  
names. If an alarm is active, the corresponding icon changes color.  
Show relay outputs  
Relay outputs are shown next to the video image as icons, along with their assigned names. If  
the relay is switched, the icon changes color.  
Show VCA trajectories  
When video content analysis (VCA) is activated, check this item to show additional  
information that traces the path of objects.  
Show VCA metadata  
When video content analysis (VCA) is activated, additional information is displayed in the live  
video stream. For example, in Motion+ mode, the sensor areas for motion detection are  
marked.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
79  
Show event log  
The event messages are displayed along with the date and time in a field next to the video  
image.  
Show system log  
The system messages are displayed along with the date and time in a field next to the video  
image and provide information about establishing and ending connections, for example.  
Allow snapshots  
Here you can specify whether the icon for saving individual images should be displayed below  
the live image. Individual images can only be saved if this icon is visible.  
Allow local recording  
Here you can specify whether the icon for saving video sequences on the local memory should  
be displayed below the live image. Video sequences can only be saved if this icon is visible.  
AutoTrack  
Enables the AutoTrack control options.  
I-frame only stream  
Here you can specify whether the Livepage displays a viewing tab for an I-frame only stream.  
Path for JPEG and Video files  
1. Enter the path for the storage location of individual images and video sequences that you  
can save from the Livepage.  
2. If necessary, click Browse to find a suitable directory.  
7.16  
Logging  
Save event log  
Check this option to save event messages in a text file on your local computer.  
You can then view, edit and print this file with any text editor or the standard Office software.  
File for event log  
1. Enter the path for saving the event log here.  
2. If necessary, click Browse to find a suitable directory.  
Save system log  
Check this option to save system messages in a text file on your local computer.  
You can then view, edit and print this file with any text editor or the standard Office software.  
File for system log  
1. Enter the path for saving the system log here.  
2. If necessary, click Browse to find a suitable directory.  
7.17  
7.18  
Advanced Mode: Camera  
Installer Menu  
Orientation  
Reverses the image 180º (ideal when mounting upside down). Set the orientation to Normal  
(default) or Inverted.  
CAUTION!  
The AutoDome disables the Privacy Mask function if the orientation is set to Inverted.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
80 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
SC Settings  
Click the Default button to restore all camera settings to their original defaults.  
SC Data  
Click the default button to clear all preposition, privacy mask, and other user settings.  
Reboot device  
Performs a reboot of the AutoDome. There is a ten (10) second pause before the dome starts  
its homing phase. During the homing phase the camera pans left and right and tilts up and  
down. It also adjusts the lens focus. The entire homing phase lasts approximately 40 seconds.  
Factory defaults  
Click Restore all defaults to restore the factory defaults for the camera. A confirmation  
screen appears. Allow 5 seconds for the camera to optimize the picture after a mode reset.  
7.19  
Encoder Profile  
For the video signal encoding, you can select a code algorithm and you can change the presets  
for the profiles.  
You can adapt the video data transmission to the operating environment (for example network  
structure, bandwidth, data load). To this end, the AutoDome 800 Series simultaneously  
generates two data streams (Dual Streaming), which compression settings you can select  
individually, for example one setting for transmissions to the Internet and one for LAN  
connections.  
Pre-programmed profiles are available, each giving priority to different perspectives.  
–
–
–
–
–
–
HD high quality / low latency  
Target bit rate: 5000 kbps  
Maximum bit rate: 10000 kbps  
Encoding interval: 30.00 ips  
HD high quality  
Target bit rate: 3500 kbps  
Maximum bit rate: 7000 kbps  
Encoding interval: 30.00 ips  
HD low bandwidth  
Target bit rate: 2500 kbps  
Maximum bit rate: 5000 kbps  
Encoding interval: 30.00 ips  
SD high quality / low latency  
Target bit rate: 2000 kbps  
Maximum bit rate: 4000 kbps  
Encoding interval: 30.00 ips  
SD high quality  
Target bit rate: 1500 kbps  
Maximum bit rate: 3000 kbps  
Encoding interval: 30.00 ips  
SD low bandwidth  
Target bit rate: 700 kbps  
Maximum bit rate: 1500 kbps  
Encoding interval: 30.00 ips  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
81  
–
–
DSL  
Target bit rate: 400 kbps  
Maximum bit rate: 500 kbps  
Encoding interval: 30.00 ips  
ISDN (2B)  
Target bit rate: 80 kbps  
Maximum bit rate: 100 kbps  
Encoding interval: 30.00 ips  
You can change individual parameter values of a profile and you can also change the name.  
You can switch between profiles by clicking the appropriate tabs.  
CAUTION!  
The profiles are rather complex. They include a large number of parameters that interact with  
one another, so it is generally best to use the default profiles.  
Change the profiles only once you are fully familiar with all the configuration options.  
In the default setting, Stream 2 is transmitted for alarm connections and automatic  
connections. Bear this fact in mind when assigning the profile.  
NOTICE!  
All parameters combine to make up a profile and are dependent on one another. If you enter a  
setting that is outside the permitted range for a particular parameter, the nearest permitted  
value will be substituted when the settings are saved.  
Profile name  
You can enter a new name for the profile here. The name is then displayed in the list of  
available profiles in the Profile name field.  
Target data rate  
You can limit the data rate for the AutoDome 800 Series to optimize utilization of the  
bandwidth in your network. The target data rate should be set according to the desired  
picture quality for typical scenes with no excessive motion.  
For complex images or frequent changes of image content due to frequent movements, this  
limit can be temporarily exceeded up to the value you enter in the Maximum data rate field.  
Maximum data rate  
This maximum data rate is not exceeded under any circumstances. Depending on the video  
quality settings for the I- and P-frames, this fact can result in individual images being skipped.  
The value entered here must be at least 10% higher than the value entered in the Target data  
rate field. If the value entered here is too low, it will automatically be adjusted.  
Video resolution  
Here you can select the desired resolution for the video image. The following resolutions are  
available for standard definition settings only:  
–
–
–
–
QVGA  
320×240 pixels  
VGA  
640 x 480 pixels  
CIF  
352 × 288/240 pixels  
4CIF/D1  
704 × 576/480 pixels  
Bosch Security Systems, Inc.  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
F.01U.273.797 | 5.0 | 2012.08  
82 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
Encoding Interval  
The figure selected here determines the interval at which images are encoded and  
transmitted. The image rate in ips (images per second) is displayed next to the text field.  
Use the slide bar to select a frame rate from 30.00 ips to 1 ips.  
Expert Settings  
Use the expert settings to adapt the I-frame quality and the P-frame quality to specific  
requirements, if necessary. The setting is based on the H.264 quantization parameter (QP).  
GOP Structure  
Select the structure you require for the Group of Pictures here. Depending on whether you  
place greater priority on having the lowest possible delay (IP frames only) or using as little  
bandwidth possible, you can choose between IP, IBP, and IBBP.  
I-frame Distance  
This parameter allows you to set the intervals in which the I-frames will be coded. 0 means  
auto mode, whereby the video server inserts I-frames as necessary. An entry of 1 indicates  
that I-frames are continuously generated. An entry of 2 indicates that only every second image  
is an I-frame, and 3 only every third image etc.; the frames in between are coded as P-frames.  
I-frame Quality  
This setting allows you to adjust the image quality of the I-frames. The basic setting Auto  
automatically adjusts the quality to the settings for the P-frame video quality. Alternatively,  
you can use the slide control to set a value between 9and51. The value 9 represents the best  
image quality with, if necessary, a lower frame refresh rate depending on the settings for the  
maximum data rate. A value of 51 results in a very high refresh rate and lower image quality.  
P-frame Quality  
This setting allows you to adjust the maximum image quality of the P-frames. The basic setting  
Auto automatically adjusts to the optimum combination of movement and image definition  
(focus). Alternatively, you can use the slide control to set a value between 9and51. The value  
9 represents the best image quality with, if necessary, a lower frame refresh rate depending  
on the settings for the maximum data rate. A value of 51 results in a very high refresh rate and  
lower image quality.  
Default  
Click Default to return the profile to the factory default values.  
7.20  
Encoder Streams  
Select the property and default profile for each H.264 stream and set the parameters for the  
M-JPEG stream.  
For the first H.264 stream you can select from these options:  
HD stream options:  
–
–
–
H.264 MP 720p30 Fixed  
H.264 MP 1080p Fixed  
H.264 MP 720p60 Fixed  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
83  
SD stream options (use these options if a second H.264 stream is allowed):  
– H.264 BP+ bit-rate-limited  
Select this setting when using hardware decoders. The bit rate is limited to 1.2 Mbps.  
CABAC: off  
CAVLC: on  
GOP structure: IP  
I-frame distance: 15  
Deblocking filter: on  
–
H.264 MP SD  
Select this setting when using software decoders, PTZ and for rapid movements in the  
images.  
CABAC: on  
CAVLC: off  
GOP structure: IP  
I-frame distance: 30  
Deblocking filter: on  
To select the stream options:  
1. Select the required encoder properties and one of the encoder profiles for each data  
stream.  
2. Click the Preview button. The preview screens for both data streams are shown.  
3. Click the 1:1 Live View button below the preview screen to open a new window with the  
original data stream and to check the image quality and the transmission rate.  
Property  
Select one of the H.264 standards for each stream.  
NOTICE!  
If you select H.264 MP 720p60 Fixed or H.264 MP 1080p Fixed as the first stream, you can  
select only Copy of Stream 1 as an option for the second stream.  
Default profile  
Select one of the following profiles for each stream:  
–
–
–
–
–
–
–
–
HD high quality / low latency  
HD high quality  
HD low bandwidth  
SD high quality / low latency  
SD high quality  
SD low bandwidth  
DSL  
ISDN (2B)  
Refer to Section 7.19 Encoder Profile, page 80, for more details about each stream.  
Preview  
Click the Preview button to open a small static preview window for each stream. To enlarge  
the preview and view live video, click the 1:1 Live View button.  
JPEG stream  
Select the resolution, frame rate, and image quality parameters for the M-JPEG stream.  
–
–
Resoltuion: Select either 4CIF/D1 or CIF.  
Frame rate: Select one of the following frame rates: 5, 10, 15, 20, 25, or 30 ips.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
84 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
–
Picture quality: his setting allows you to adjust the image quality. Use the slide bar to  
choose a quality between Low and High.  
7.21  
Privacy Masks  
Privacy Masking is used to block out a specific area of a scene from being viewed. Masks can  
be configured as a gray area with four corners. You may define a total of 24 privacy masks.  
NOTICE!  
–
The AutoDome disables the Privacy Mask feature if the orientation of the camera is set to  
Inverted. Refer to Section 7.18 Installer Menu, page 79, for orientation settings.  
You cannot apply a privacy mask 70° (tilt direction) below the horizon.  
–
To add a privacy mask to a scene:  
1. Navigate to the scene in which you want to apply a privacy mask.  
a. Click the View Control link.  
b. Use the PTZ controls to view the scene.  
2. Select the privacy mask number to apply to the scene.  
The preview window displays a gray rectangle in the scene.  
3. Click the Enable check box to activate the privacy mask.  
The privacy mask in the preview window changes to orange to indicate that the mask will  
appear in the video streams on the Livepage.  
4. Select a mask color from the Pattern list box.  
5. Place the cursor inside the privacy mask area in the preview window; then click and drag  
to move the privacy mask.  
6. Place the cursor on a corner or on a side of the mask rectangle; then click and drag to  
expand or shrink the privacy mask area.  
NOTICE!  
Draw the mask 10% larger than the object to ensure that the mask completely covers the  
object as the AutoDome zooms in and out.  
7. Click Set to save the privacy mask size and position.  
An image window displays the privacy mask.  
8. To hide an individual mask, select the mask number and clear the Enable check box.  
9. To hide all masks from an image view, click the Hide Masks check box.  
Note: If you choose to hide all masks, you must enable each enable each individual mask  
to show the mask in the scene.  
7.22  
Camera Settings  
White Balance  
Adjusts the color settings to maintain the quality of the white areas of the image.  
–
–
–
–
–
ATW: allows the camera to continuously adjust color reproduction.  
Indoor: white balance tracking for indoor use.  
Outdoor: white balance tracking for outdoor use.  
AWB Hold: places the ATW on hold and saves the color settings.  
Extended ATW (default): allows the camera to constantly adjust for optimal color  
reproduction.  
–
–
Manual: Red and Blue gain can be manually set to a desired position.  
Outdoor Auto: Automatically adjusts the white balance to reduce the dark tones at dawn  
or dusk.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
85  
–
–
Sodium Lamp Auto: Automatically adjusts for sodium vapor light to restore objects to  
their original color.  
Sodium Lamp: Optimizes the sodium vapor light to restore objects to their original color.  
Red Gain  
The red gain adjustment offsets the factory white point alignment (reducing red introduces  
more cyan).  
Blue Gain  
The blue gain adjustment offsets the factory white point alignment (reducing blue introduces  
more yellow). It is only necessary to change the white point offset for special scene  
conditions.  
Gain Control  
Adjusts the automatic gain control (AGC). Automatically sets the gain to the lowest possible  
value needed to maintain a good picture.  
–
AGC (default): electronically brightens dark scenes, which may cause graininess in low  
light scenes.  
–
Fixed: no enhancement. This setting disables the Max. Gain Level option.  
If you select this option, the AutoDome 800 Series makes the following changes  
automatically:  
–
–
Night Mode: switches to Color  
Auto Iris: switches to Constant  
Max. Gain Level  
Controls the maximum value the gain can have during AGC operation. To set the maximum  
gain level, choose from:  
–
–
–
Normal  
Medium  
High  
Sharpness  
Adjusts the sharpness of the picture. To set the sharpness, type a value between 1 and 15  
inclusive. The default setting is 12.  
Shutter Mode  
–
–
Off: turns the Auto SensUP Off.  
AutoSensUp: increases camera sensitivity by increasing the integration time on the  
camera. This is accomplished by integrating the signal from a number of consecutive  
video frames to reduce signal noise.  
If you select this option, the AutoDome makes the following change automatically:  
–
Auto Iris: switches to Constant  
Shutter  
Adjusts the electronic shutter speed (AES). Controls the time period for which light is  
gathered by the collecting device. The default setting is 1/30 second and the range of settings  
is from 1/1 to 1/10000.  
Backlight Compensation  
Optimizes the video level for the selected area of the image. Parts outside this area may be  
underexposed or overexposed. Select On to optimize the video level for the central area of  
the image. The default setting is Off.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
86 en | Configuring the AutoDome 800 Series  
High Sensitivity Setting  
Night Mode  
AutoDome 800 Series HD PTZ Camera  
Selects night mode (B/W) to enhance lighting in low light scenes. Select from the following  
options:  
–
–
–
Off: Forces the camera to stay in Nigh Mode and transmit monochrome images.  
On: The camera does not switch to Night Mode regardless of ambient light conditions.  
Auto: The camera switches out of Night Mode after the ambient light level reaches a pre-  
defined threshold.  
Night Mode Threshold  
Adjusts the level of light at which the camera automatically switches out of night mode (B/W)  
operation. Select a value between 10 and 55 (in increments of 5), where 10 is earlier and 55 is  
later.  
Noise Reduction  
Turns on the 2D and 3D noise reduction feature.  
Noise Reduction Level  
Adjusts the noise level to the appropriate level for shooting conditions. Select a value  
between 1 and 5.  
7.23  
Lens Settings  
Auto Focus  
Continuously adjusts the lens automatically to the correct focus for the sharpest picture.  
–
One Push (default): activates the Auto Focus feature after the camera stops moving.  
Once focused, Auto Focus is inactive until the camera is moved again.  
Auto Focus: Auto Focus is always active.  
–
–
Manual: Auto Focus is inactive.  
Focus Polarity  
–
–
Normal (default): focus controls operate normally.  
Reverse: focus controls are reversed.  
Focus Speed  
Controls how fast the Auto focus will readjust when the focus becomes blurred. Select from  
the following options:  
–
–
–
–
Super Slow  
Slow  
Medium  
Fast  
Auto Iris  
Automatically adjusts the lens to allow the correct illumination of the camera sensor. This type  
of lens is recommended for use where there are low light or changing light conditions.  
–
Constant (default): camera constantly adjusts to varying light conditions (default).  
If you select this option, the AutoDome makes the following changes automatically:  
–
–
Gain Control: switches to AGC  
Shutter Speed: switches to default  
–
Manual: camera must be manually adjusted to compensate for varying light conditions.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
87  
Iris Polarity  
Capability to reverse the operation of the iris button on the controller.  
–
–
Normal (default): iris controls operate normally.  
Reverse: iris controls are reversed.  
Auto Iris Level  
Increases or decreases brightness according to the amount of light. Type a value between 1  
and 15, inclusive. The default setting is 5.  
Maximum Zoom Speed  
Controls the zoom speed. The default setting is Fast.  
Zoom Polarity  
Capability to reverse the operation of the zoom button on the controller.  
–
–
Normal (default): zoom controls operate normally.  
Reverse: zoom controls are reversed.  
Digital Zoom  
Digital zoom is a method of decreasing (narrowing) the apparent angle of view of a digital  
video image. It is accomplished electronically, without any adjustment of the camera's optics,  
and no optical resolution is gained in the process. Select Off to disable or On to enable this  
feature. The default setting is On.  
7.24  
PTZ Settings  
Auto Pan Speed  
Pans the camera at the selected speed between right and left limit settings or 360°. Type a  
value between 1 and 60 (expressed in degrees), inclusive. The default setting is 30.  
Inactivity  
Selects the time period the dome must be not controlled until the inactivity event will be  
executed.  
–
–
–
Off (default): camera remains on a current scene indefinitely.  
Scene 1: camera returns to Preset 1.  
Previous Aux: camera returns to the previous activity.  
Inactivity Period  
Determines the behavior of the dome when the control for dome is inactive. Select a time  
period from the pull-down list (3 sec. - 10 min.). The default setting is 2 minutes.  
Auto Pivot  
The Auto Pivot tilts the camera through the vertical position as the camera is rotated to  
maintain the correct orientation of the image. Set the Auto Pivot to On (default) to  
automatically rotate the camera 180º when following a subject traveling directly beneath the  
camera. To disable this feature, click Off.  
Freeze Frame  
Select On (default) to freeze the image while the AutoDome moves to a predetermined scene  
position.  
Autopan Left Limit  
Sets the left Auto Pan limit of the camera. Use the preview window to move the camera to the  
left pan limit and click the button. The camera will not move past this limit when in Auto Pan  
Between Limits mode (AUX 2 ON).  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
88 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
Autopan Right Limit  
Sets the right Auto Pan limit of the camera. Use the preview window to move the camera to  
the right pan limit and click the button. The camera will not move past this limit when in Auto  
Pan Between Limits mode (AUX 2 ON).  
Tilt Up Limit  
Sets the upper tilt limit of the camera.  
Tilt Limits  
Click the Reset button to clear the upper tilt limit.  
Tour A / Tour B  
Starts and stops the recording of a recorded (guard) tour.  
The AutoDome can make up to two (2) recorded tours. A Recorded Tour saves all manual  
camera movements made during the recording, including its rate of pan, tilt and zoom speeds  
and other lens setting changes.  
Note: You can save a total of 15 minutes of recorded actions between the two tours.  
To record a tour:  
1. Click the Start Recording button. The system prompts you to overwrite the existing tour.  
2. Click Yes to overwrite the existing tour movements.  
3. Click the View Control link, under the image cameo, to access the directional and zoom  
controls.  
4. Use the View Control dialog box to make the necessary camera movements.  
5. Click the Stop Recording button to save all actions.  
Compass  
The VG5 AutoDome allows a user to display the compass heading of the camera in the lower-  
right corner of the image display. The AutoDome displays the The cardinal or intercardinal (N,  
NE, E, SE, S, SW, W, NW) heading in which the camera is pointing.  
NOTICE!  
The compass feature is not compatible with Bosch Intelligent Tracking. If Intelligent Tracking  
is activated, the camera automatically disables the display of the compass heading. Once  
Intelligent Tracking is deactivated, the camera returns the compass heading to the display.  
You must first calibrate the AutoDome to North before the camera displays accurate compass  
headings. The AutoDome uses this calibration, usually set to magnetic North, as the zero  
degree pan position and as the North compass heading. The AutoDome then displays the  
compass heading based on the number of degrees from the North calibration point.  
To set the North calibration point:  
1. Determine the North compass heading, then move the camera to that position.  
2. Click the Set North Compass Point button to set the calibration point.  
3. Click the On radio button for the Compass parameter.  
7.25  
Diagnostics  
Accesses the Built-in Self Test (BIST). Click the BIST button to display the number of times  
the AutoDome 800 Series:  
–
–
–
–
performed a homing event.  
failed to home properly.  
restarted.  
lost video.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
89  
7.26  
Preposition and Tours  
The AutoDome 800 Series can store up to 99 preset scenes and this section allows you to  
define the individual scenes that comprise a preposition tour.  
You define individual preposition scenes, then use these scenes to define the preposition  
tour. The tour starts from the lowest scene number in the tour and progresses sequentially to  
the highest scene number in the tour. The tour displays each scene for a specified dwell time  
before advancing to the next scene.  
By default, all scenes are part of the preposition tour unless removed.  
To define and edit an individual scene:  
1. Navigate to the scene that you want to define as a preposition.  
a. Click the View Control link.  
b. Use the PTZ controls to move the camera into position.  
2. Click the Add scene (“+”) button to define the preposition.  
3. Select a number for the scene, from 1 to 99.  
4. Type an optional name for the scene, up to 20 characters long.  
5. Click OK to save the scene to the Preposition list.  
The asterisk (*) to the left of the scene name indicates the scene is part of the  
preposition tour.  
6. To delete a scene from the list, select the scene and click the Delete scene (“X”) button.  
7. To overwrite an existing scene:  
a. Click the View Control link to access the PTZ controls.  
b. Use the PTZ controls to navigate to the new scene.  
c. Click the scene in the Preposition list you want to overwrite.  
d. Click the Overwrite scene button to apply the new scene to the existing preposition.  
e. To change the name of the scene, double-click the scene in the list. Then, change the  
name in the Edit Scene dialog box and click OK.  
8. To view a scene in the preview window, select the scene in the list and click the Show  
scene button.  
9. To view a scene from the Livepage:  
a. Click a scene number below the PTZ controls on the View Control tab.  
b. Use the keypad and the Show Shot button on the Aux Control tab.  
To define a preposition tour:  
1. Create the individual scenes.  
By default, all scenes in the Preposition list are in the preposition tour.  
2. To remove a scene from the tour, select the scene in the list and uncheck the Include in  
standard tour box.  
3. Select a dwell time from the Standard preposition tour drop-down list.  
4. To start the preposition tour:  
a. Return to the Livepage.  
b. Click the Aux Control tab.  
c. Type 8 in the input box and click the Aux On button.  
5. To stop the tour, type 8 and click the Aux Off button.  
7.27  
Sectors  
Sector  
The AutoDome 800 Series pan capability is 360° and is divided into 16 equal sectors. This  
section allows you to apply a title for each sector and to designate any sectors as a Blanked  
Sector.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
90 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
To define a title for sectors:  
1. Place the cursor in the input box to the right of the sector number.  
2. Type a title for the sector, up to 20 characters long.  
3. To blank the sector, click the check box to the right of the sector title.  
7.28  
7.29  
Miscellaneous  
Address  
Allows the appropriate dome to be operated via the numerical address in the control system.  
Type a number between 0000 and 9999, inclusive, to identify the camera.  
Logs  
To save the log file information:  
1. Click Download to obtain the log information.  
2. Click Save.  
3. Navigate to the directory in which you want to store the log information.  
4. Type a name for the log file and click Save.  
7.30  
Audio  
You can set the gain of the audio signals to suit your specific requirements. The current video  
image is shown in the small window next to the slide controls to help you check the audio  
source and improve assignments. Your changes are effective immediately.  
If you connect via Web browser, you must activate the audio transmission on the Livepage  
Functions page (see Section 6.6 The Livepage, page 61). For other connections, the  
transmission depends on the audio settings of the respective system.  
Audio  
The audio signals are sent in a separate data stream parallel to the video data, and so increase  
the network load. The audio data are encoded according to G.711 and require an additional  
bandwidth of approx. 80 kbps for each connection. If you do not want any audio data to be  
transmitted, select Off.  
Line In  
You can set the line input gain. Make sure that the display does not go beyond the green zone  
during modulation.  
Record Format  
Select a format for audio recording. The default value is G.711. Select L16 or AAC (Advanced  
Audio Coding) if you want better audio quality with higher sampling rates. The L16 standard  
requires approx. eight times the G.711 bandwidth.  
7.31  
Pixel Counter  
Counts the number of pixels in a defined image area. The pixel counter allows the installer to  
easily verify that the camera installation fulfills any regulatory or specific customer  
requirements, for example, calculating the pixel resolution of the face of a person passing a  
doorway monitored by the camera.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
91  
7.32  
7.33  
Advanced Mode: Recording  
Storage Management  
You can record the images from the AutoDome 800 Series on various local storage media or  
on an appropriately configured iSCSI system.  
It is also possible to let the VRM Video Recording Manager control all recording when  
accessing an iSCSI system. This is an external program for configuring recording tasks for  
video servers. For further information please contact your local customer service at Bosch  
Security Systems, Inc.  
Device manager  
If you activate the VRM option in this screen, the VRM Video Recording Manager will manage  
all recording and you will not be able to configure any further settings here.  
CAUTION!  
Activating or deactivating VRM causes the current settings to be lost; they can only be  
restored through reconfiguration.  
Recording media  
Select the required recording media here so that you can then activate them and configure  
the recording parameters.  
iSCSI Media  
If you want to use an iSCSI system as a recording medium, you must set up a connection to  
the required iSCSI system and set the configuration parameters.  
NOTICE!  
The iSCSI storage system selected must be available on the network and completely set up.  
Amongst other things, it must have an IP address and be divided into logical drives (LUN).  
1. Enter the IP address of the required iSCSI destination in the iSCSI IP address field.  
2. If the iSCSI destination is password protected, enter this into the Password field.  
3. Click the Read button. The connection to the IP address will be established. In the  
Storage overview field, you can see the corresponding logical drives.  
Local Media  
The supported local recording media are displayed in the Storage overview field.  
Activating and Configuring Storage Media  
The storage overview displays the available storage media. You can select individual media or  
iSCSI drives and transfer these to the Managed storage media list. You can activate the  
storage media in this list and configure them for storage.  
CAUTION!  
Each storage medium can only be associated with one user. If a storage medium is already  
being used by another user, you can decouple the user and connect the drive with the  
AutoDome 800 Series. Before decoupling, make absolutely sure that the previous user no  
longer needs the storage medium.  
1. In the Recording media section, click the iSCSI Media and Local Media tabs to display  
the applicable storage media in the overview.  
2. In the Storage overview section, double-click the required storage medium, an iSCSI  
LUN or one of the other available drives. The medium is then added to the Managed  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
92 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
storage media list. In the Status column, newly added media are indicated by the status  
Not active.  
3. Click the Set button to activate all media in the Managed storage media list. In the  
Status column, these are indicated by the status Online.  
4. Check the box in the Rec. 1 or Rec. 2 to specify which data stream should be recorded  
on the storage media selected. Rec. 1 stores Stream 1, Rec. 2 stores Stream 2. This  
means that you can record the standard data stream on a hard drive and record alarm  
images on the mobile CF card, for example.  
5. Check the boxes for the Overwrite older recordings option to specify which older  
recordings can be overwritten once the available memory capacity has been used.  
Recording 1 corresponds to Stream 1, Recording 2 corresponds to Stream 2.  
CAUTION!  
If older recordings are not allowed to be overwritten when the available memory capacity has  
been used, the recording in question will be stopped. You can specify limitations for  
overwriting old recordings by configuring the retention time (see Section 7.35 Retention Time,  
page 94).  
Formatting Storage Media  
You can delete all recordings on a storage medium at any time.  
CAUTION!  
Check the recordings before deleting and back up important sequences on the computer's  
hard drive.  
1. Click a storage medium in the Managed storage media list to select it.  
2. Click the Edit button below the list. A new window will open.  
3. Click the Formatting button to delete all recordings in the storage medium.  
4. Click OK to close the window.  
Deactivating Storage Media  
You can deactivate any storage medium from the Managed storage media list. It is then no  
longer used for recordings.  
1. Click a storage medium in the Managed storage media list to select it.  
2. Click the Remove button below the list. The storage medium is deactivated and removed  
from the list.  
7.34  
Recording Profiles  
You can define up to ten different recording profiles. You will then use these recording  
profiles in the recording scheduler, where they are linked with the individual days and times  
(see Section 7.36 Recording Schedule, page 94).  
NOTICE!  
You can change or add to the recording profile description on the tabs on the Recording  
Scheduler page (see Page 94).  
1. Click one of the tabs to edit the corresponding profile.  
2. If necessary, click the Default button to return all settings to their default values.  
3. Click the Copy Settings button if you want to copy the currently visible settings to other  
profiles. A new window will open and you can select the profiles in which you want to  
copy the settings.  
4. For each profile, click the Set button to save the settings in the unit.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
93  
Standard recording  
Here you can select the mode for standard recordings.  
If you select Continuous, the recording proceeds continuously. If the maximum memory  
capacity is reached, older recordings will automatically be overwritten. If you select the Pre-  
alarm option, recording will only take place in the pre-alarm time, during the alarm and during  
the set post-alarm time.  
If you select Off, no automatic recording takes place.  
CAUTION!  
You can specify limitations for overwriting older recordings in Continuous mode by  
configuring the retention time (see Section 7.35 Retention Time, page 94).  
Standard profile  
From this field, you can select the encoder profile to be used for recording (see  
Section 7.19 Encoder Profile, page 80).  
NOTICE!  
The recording profile can deviate from the standard setting Active profile and is only used  
during an active recording.  
Pre-alarm Time  
You can select the required pre-alarm time from the list field.  
Post-alarm Time  
You can select the required post-alarm time from the list field.  
Post-alarm profile  
You can select the encoder profile to be used for recording during the post-alarm time (see  
Section 7.19 Encoder Profile, page 80).  
The Standard profile option adopts the selection at the top of the page.  
Alarm input / Motion alarm / Video loss alarm  
Here you can select the alarm sensor that is to trigger a recording.  
Virtual alarm  
Here you can select the virtual alarm sensors that are to trigger a recording, via RCP+  
commands or alarm scripts, for example.  
NOTICE!  
For more information, please see the Alarm Task Script Language document and the RCP+  
documentation. These documents can be found on the product CD supplied.  
Recording includes  
You can specify whether, in addition to video data and metadata (for example alarms, VCA  
data and serial data) should also be recorded. Including metadata could make subsequent  
searches of recordings easier but it requires additional memory capacity.  
CAUTION!  
Without metadata, it is not possible to include video content analysis in recordings.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
94 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
7.35  
Retention Time  
You can specify the retention times for recordings. If the available memory capacity of a  
medium has been used, older recordings are only overwritten if the retention time entered  
here has expired.  
NOTICE!  
Make sure that the retention time corresponds with the available memory capacity. A rule of  
thumb for the memory requirement is as follows: 1 GB per hour retention time with 4CIF for  
complete frame rate and high image quality.  
Retention time  
Enter the required retention time in hours or days for each recording. Recording 1  
corresponds to Stream 1, Recording 2 corresponds to Stream 2.  
7.36  
Recording Schedule  
The recording scheduler allows you to link the created recording profiles with the days and  
times at which the camera's images are to be recorded in the event of an alarm.  
You can link any number of 15-minute intervals with the recording profiles for each day of the  
week. Moving the mouse cursor over the table displays the time below it. This aids  
orientation.  
In addition to the normal weekdays, you can define holidays that are not in the standard  
weekly schedule on which recordings are to apply. This allows you to apply a schedule for  
Sundays to other days with dates that fall on varying weekdays.  
1. Click the profile you want to link in the Time periods field.  
2. Click in a field in the table, hold down the mouse button and drag the cursor over all the  
periods to be assigned to the selected profile.  
3. Use the right mouse button to deselect any of the intervals.  
4. Click the Select All button to link all time intervals to the selected profile.  
5. Click the Clear All button to deselect all of the intervals.  
6. When you are finished, click the Set button to save the settings in the unit.  
Holidays  
You can define holidays that are not in the standard weekly schedule on which recordings are  
to apply. This allows you to apply a schedule for Sundays to other days with dates that fall on  
varying weekdays.  
1. Click the Holidays tab. Any days that have already been selected will be shown in the  
table.  
2. Click the Add button. A new window will open.  
3. Select the desired date from the calendar. You can select several consecutive calendar  
days by holding down the mouse button. These will later be displayed as a single entry in  
the table.  
4. Click OK to accept the selection. The window will close.  
5. Assign the individual holidays to the recording profiles, as described above.  
Deleting Holidays  
You can delete holidays you have defined yourself at any time.  
1. Click the Delete button. A new window will open.  
2. Click the date you wish to delete.  
3. Click OK. The item will be deleted from the table and the window will close.  
4. The process must be repeated for deleting additional days.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
95  
Time periods  
You can change the names of the recording profiles.  
1. Click a profile and then the Rename button.  
2. Enter your chosen name and then click the Rename button again.  
Activating the Recording  
After completing configuration you must activate the recording scheduler and start the  
recording. Once recording is underway, the Recording Profiles and Recording Scheduler  
pages are deactivated and the configuration cannot be modified.  
You can stop the recording activity at any time and modify the settings.  
1. Click the Start button to activate the recording scheduler.  
2. Click the Stop button to deactivate the recording scheduler. Running recordings are  
interrupted and the configuration can be changed.  
Recording status  
The graphic indicates the recording activity of the AutoDome 800 Series. You will see an  
animated graphic while recording is taking place.  
7.37  
Recording Status  
Certain details on the recording status are displayed here for information purposes. You  
cannot change any of these settings.  
7.38  
7.39  
Advanced Mode: Alarm  
Alarm Connections  
You can select how the AutoDome 800 Series responds to an alarm. In the event of an alarm,  
the unit can automatically connect to a pre-defined IP address. You can enter up to ten IP  
addresses to which the AutoDome 800 Series will connect in sequence in the event of an  
alarm, until a connection is made.  
Connect on alarm  
Select On so that the AutoDome 800 Series automatically connects to a predefined IP address  
in the event of an alarm.  
By setting Follows input 1 the unit maintains the connection that has been automatically  
established for as long as an alarm exists on alarm input 1.  
NOTICE!  
In the default setting, Stream 2 is transmitted for alarm connections. Bear this fact in mind  
when assigning the profile (see Section 7.19 Encoder Profile, page 80).  
Number of destination IP address  
Specify the numbers of the IP addresses to be contacted in the event of an alarm. The unit  
contacts the remote stations one after the other in the numbered sequence until a connection  
is made.  
Destination IP address  
For each number, enter the corresponding IP address for the desired remote station.  
Destination password  
If the remote station is password protected, enter the password here.  
In this page, you can save a maximum of ten destination IP addresses and hence up to ten  
passwords for connecting to remote stations. If connections to more than ten remote stations  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
96 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
are to be possible, for example when initiating connections via higher-ranking systems such as  
VIDOS or Bosch Video Management System, you can store a general password here. The  
AutoDome 800 Series can use this general password to connect to all remote stations  
protected with the same password. In this case, proceed as follows:  
1. Select 10 from the Number of destination IP address list field.  
2. Enter the address 0.0.0.0 in the Destination IP address field.  
3. Enter your chosen password in the Destination password field.  
4. Define this password as the user password for all remote stations to which a connection  
is to be possible.  
NOTICE!  
If you enter the destination IP address 0.0.0.0 for destination 10, this address will no longer  
be used for the tenth attempt at automatic connection in the event of an alarm. The parameter  
is then used only to save the general password.  
Video transmission  
If the unit is operated behind a firewall, TCP (HTTP port) should be selected as the transfer  
protocol. For use in a local network, select UDP.  
CAUTION!  
Please note that in some circumstances, a larger bandwidth must be available on the network  
for additional video images in the event of an alarm, in case Multicast operation is not  
possible. To enable Multicast operation, select the UDP option for the Video transmission  
parameter here and on the Network page (see Page 105).  
Remote port  
Depending on the network configuration, select a browser port here. The ports for HTTPS  
connections will be available only if the On option is selected in the SSL encryption  
parameter.  
Video output  
If you know which unit is being used as the receiver, you can select the analog video output to  
which the signal should be switched. If the destination unit is unknown, it is advisable to  
select the First available option. In this case, the image is placed on the first free video  
output. This is an output on which there is no signal. The connected monitor only displays  
images when an alarm is triggered. If you select a particular video output and a split image is  
set for this output on the receiver, you can also select from Decoder the decoder in the  
receiver that is to be used to display the alarm image.  
NOTICE!  
Refer to the destination unit documentation concerning image display options and available  
video outputs.  
Decoder  
Select a decoder of the receiver to display the alarm image. The decoder selected has an  
impact on the position of the image in a split screen. For example, you can specify via a VIP XD  
that the upper-right quadrant should be used to display the alarm image by selecting decoder  
2.  
SSL encryption  
The data for the connection, for example the password, can be securely transmitted with SSL  
encryption. If you have selected the On option, only encrypted ports are offered in the  
Remote port parameter.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
97  
NOTICE!  
Please note that the SSL encryption must be activated and configured at both ends of a  
connection. This requires the appropriate certificates to be uploaded onto the AutoDome 800  
Series.  
You can activate and configure encryption of the media data (video and metadata) on the  
Encryption page (see Section 7.54 Encryption, page 111).  
Auto-connect  
Select the On option to automatically re-establish a connection to one of the previously  
specified IP addresses after each reboot, after a connection breakdown or after a network  
failure.  
NOTICE!  
In the default setting, Stream 2 is transmitted for automatic connections. Bear this fact in  
mind when assigning the profile (see Section 7.19 Encoder Profile, page 80).  
7.40  
VCA  
The AutoDome 800 Series contains an integrated video content analysis (VCA), which can  
detect and analyze changes in the signal on the basis of image processing. Such changes can  
be due to movements in the camera's field of view.  
You can select various VCA configurations and adapt these to your application as required.  
The Silent MOTION+ configuration is active by default. In this configuration, metadata is  
created to facilitate searches of recordings; however, no alarm is triggered.  
1. Select a VCA configuration and make the required settings.  
2. If necessary, click the Default button to return all settings to their default values.  
VCA Profiles  
You can configure two profiles with different VCA configurations. You can save profiles on  
your computer's hard drive and load saved profiles from there. This can be useful if you want  
to test a number of different configurations. Save a functioning configuration and test new  
settings. You can use the saved configuration to restore the original settings at any time.  
NOTICE!  
If computing power becomes short, the highest priority is always the live images and  
recordings. This can lead to impairment of the video content analysis. You should therefore  
observe the processor load and optimize the encoder settings or the video content analysis  
settings as necessary.  
1. Select a VCA profile and enter the required settings.  
2. If necessary, click the Default button to return all settings to their default values.  
3. Click the Save... button to save the profile settings to another file. A new window is  
opened, in which you can specify where you want to save the file and what name you  
want to save it under.  
4. Click the Load... button to load a saved profile. A new window opens in which you can  
select the profile file and specify where to save the file.  
VCA configuration  
Select one of the profiles here to activate it or edit it.  
You can rename the profile.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
98 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
1. To rename the file, click the icon to the right of the list field and enter the new profile  
name in the field.  
2. Click the icon again. The new profile name is saved.  
Alarm status  
The alarm status is displayed here for information purposes. This means you can check the  
effects of your settings immediately.  
Analysis type  
Select the required analysis algorithm. By default, only MOTION+ is available – this offers a  
motion detector and essential recognition of tampering.  
NOTICE!  
Additional analysis algorithms with comprehensive functions such as IVMD and IVA are  
available from Bosch Security Systems, inc.  
If you select one of these algorithms, you can set the corresponding parameters here directly.  
You can find information on this in the relevant documents on the product CD supplied.  
Metadata is always created for a video content analysis, unless this was explicitly excluded.  
Depending on the analysis type selected and the relevant configuration, additional  
information overlays the video image in the preview window next to the parameter settings.  
With the MOTION+ analysis type, for example, the sensor fields in which motion is recorded  
will be marked with rectangles.  
NOTICE!  
On the LIVEPAGE Functions page, you can also enable additional information overlays for the  
LIVEPAGE (see Section 7.15 Livepage Functions, page 78).  
Motion detector (MOTION+ only)  
For the detector to function, the following conditions must be met:  
–
–
–
Analysis must be activated.  
At least one sensor field must be activated.  
The individual parameters must be configured to suit the operating environment and the  
desired responses.  
–
The sensitivity must be set to a value greater than zero.  
CAUTION!  
Reflections of light (off glass surfaces, etc.), switching lights on or off or changes in the light  
level caused by cloud movement on a sunny day can trigger unintended responses from the  
motion detector and generate false alarms. Run a series of tests at different times of the day  
and night to ensure that the video sensor is operating as intended.  
For indoor surveillance, ensure constant lighting of the areas during the day and at night.  
Sensitivity (MOTION+ only)  
The basic sensitivity of the motion detector can be adjusted for the environmental conditions  
to which the camera is subject.  
The sensor reacts to variations in the brightness of the video image. The darker the  
observation area, the higher the value that must be selected.  
Minimum object size (MOTION+ only)  
You can specify the number of sensor fields that a moving object must cover to generate an  
alarm. This is to prevent objects that are too small from triggering an alarm.  
A minimum value of 4 is recommended. This value corresponds to four sensor fields.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en  
99  
Debounce time 1 s (MOTION+ only)  
The debounce time is intended to prevent very brief alarm events from triggering individual  
alarms. If the Debounce time 1 s option is activated, an alarm event must last at least one  
second to trigger an alarm.  
Select Area (MOTION+ only)  
The areas of the image to be monitored by the motion detector can be selected. The video  
image is subdivided into 858 square fields. Each of these fields can be activated or  
deactivated individually. If you wish to exclude particular regions of the camera's field of view  
from monitoring due to continuous movement (by a tree in the wind, etc.), the relevant fields  
can be deactivated.  
1. Click Select Area to configure the sensor fields. A new window will open.  
2. If necessary, click Clear All first to clear the current selection (fields marked yellow).  
3. Left-click the fields to be activated. Activated fields are marked yellow.  
4. If necessary, click Select All to select the entire video frame for monitoring.  
5. Right-click any fields you wish to deactivate.  
6. Click OK to save the configuration.  
7. Click the close button X in the window title bar to close the window without saving the  
changes.  
Tamper detection  
You can reveal the tampering of cameras and video cables by means of various options. Run a  
series of tests at different times of the day and night to ensure that the video sensor is  
operating as intended.  
NOTICE!  
The options for tamper detection can only be set for fixed cameras. Dome cameras or other  
motorized cameras cannot be protected in this manner as the movement of the camera itself  
causes changes in the video image that are too great.  
Sensitivity  
NOTICE!  
This and the following parameter are only accessible if the reference check is activated.  
The basic sensitivity of the tamper detection can be adjusted for the environmental conditions  
to which the camera is subject.  
The algorithm reacts to the differences between the reference image and the current video  
image. The darker the observation area, the higher the value that must be selected.  
Trigger delay (s)  
You can set delayed alarm triggering. The alarm is only triggered after a set time interval in  
seconds has elapsed and then only if the triggering condition still exists. If the original  
condition has been restored before this time interval elapses, the alarm is not triggered. This  
allows you to avoid false alarms triggered by short-term changes, for example cleaning  
activities in the direct field of vision of the camera.  
Global change  
You can set how large the global change in the video image must be for an alarm to be  
triggered. This setting is independent of the sensor fields selected under Select Area. Set a  
high value if fewer sensor fields need to change to trigger an alarm. With a low value, it is  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
100 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
necessary for changes to occur simultaneously in a large number of sensor fields to trigger an  
alarm.  
This option allows you to detect, independently of motion alarms, manipulation of the  
orientation or location of a camera resulting from turning the camera mount bracket, for  
instance.  
Global change  
Activate this function if the global change, as set with the Global change slide control, should  
trigger an alarm.  
Scene too bright  
Activate this function if tampering associated with exposure to extreme light (for instance,  
shining a flashlight directly on the lens) should trigger an alarm. The average brightness of the  
scene provides a basis for recognition.  
Scene too dark  
Activate this function if tampering associated with covering the lens (for instance, by spraying  
paint on it) should trigger an alarm. The average brightness of the scene provides a basis for  
recognition.  
Scene too noisy  
Activate this function if tampering associated with EMC interference (noisy scene as the result  
of a strong interference signal in the vicinity of the video lines), as an example, should trigger  
an alarm.  
Reference Check  
You can save a reference image that is continuously compared with the current video image. If  
the current video image in the marked areas differs from the reference image, an alarm is  
triggered. This allows you to detect tampering that would otherwise not be detected, for  
example if the camera is turned.  
1. Click Reference to save the currently visible video image as a reference.  
2. Click Select Area and select the areas in the reference image that are to be monitored.  
3. Check the box Reference check to activate on-going matching. The stored reference  
image is displayed in black and white below the current video image, and the selected  
areas are marked in yellow.  
4. Select the Disappearing edges or Appearing edges option to specify the reference check  
once again.  
Disappearing edges  
The area selected in the reference image should contain a prominent structure. If this  
structure is concealed or moved, the reference check triggers an alarm. If the selected area is  
too homogenous, so that concealing and moving the structure would not trigger an alarm,  
then an alarm is triggered immediately to indicate the inadequate reference image.  
Appearing edges  
Select this option if the selected area of the reference image includes a largely homogenous  
surface. If structures appear in this area, then an alarm is triggered.  
Select Area  
You can select the image areas in the reference image that are to be monitored. The video  
image is subdivided into 858 square fields. Each of these fields can be activated or  
deactivated individually.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en 101  
NOTICE!  
Select only those areas for reference monitoring in which no movement takes place and that  
are always evenly lit, as false alarms could otherwise be triggered.  
1. Click Select Area to configure the sensor fields. A new window will open.  
2. If necessary, click Clear All first to clear the current selection (fields marked yellow).  
3. Left-click the fields to be activated. Activated fields are marked yellow.  
4. If necessary, click Select All to select the entire video frame for monitoring.  
5. Right-click any fields you wish to deactivate.  
6. Click OK to save the configuration.  
7. Click the close button X in the window title bar to close the window without saving the  
changes.  
7.41  
Audio Alarm  
The AutoDome 800 Series can create alarms on the basis of audio signals. You can configure  
signal strengths and frequency ranges in such a way that false alarms, for example due to  
machine noise or background noise, are avoided.  
NOTICE!  
First set up normal audio transmission before you configure the audio alarm here (see  
Section 7.30 Audio, page 90).  
Audio alarm  
Select On if you want the device to generate audio alarms.  
Name  
The name makes it easier to identify the alarm in extensive video monitoring systems, for  
example with the VIDOS and Bosch Video Management System programs. Enter a unique and  
clear name here.  
CAUTION!  
Do not use any special characters, for example &, in the name.  
Special characters are not supported by the system's internal recording management and may  
therefore result in the Player or Archive Player programs being unable to play back the  
recording.  
Threshold  
Set up the threshold on the basis of the signal visible in the graphic. You can set the threshold  
using the slide control or, alternatively, you can move the white line directly in the graphic  
using the mouse.  
Sensitivity  
You can use this setting to adapt the sensitivity to the sound environment. You can effectively  
suppress individual signal peaks. A high value represents a high level of sensitivity.  
Signal Ranges  
You can exclude particular signal ranges in order to avoid false alarms. For this reason the  
total signal is divided into 13 tonal ranges (mel scale). Check or uncheck the boxes below the  
graphic to include or exclude individual ranges.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
102 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
7.42  
Alarm E-Mail  
As an alternative to automatic connecting, alarm states can also be documented by e-mail. In  
this way it is possible to notify a recipient who does not have a video receiver. In this case, the  
AutoDome 800 Series automatically sends an e-mail to a previously defined e-mail address.  
Send alarm e-mail  
Select On if you want the unit to automatically send an alarm e-mail in the event of an alarm.  
Mail server IP address  
Enter the IP address of a mail server that operates on the SMTP standard (Simple Mail  
Transfer Protocol). Outgoing e-mails are sent to the mail server via the address you entered.  
Otherwise leave the box blank (0.0.0.0).  
SMTP user name  
Enter a registered user name for the chosen mailserver here.  
SMTP password  
Enter the required password for the registered user name here.  
Format  
You can select the data format of the alarm message.  
–
–
Standard (with JPEG)  
E-mail with attached JPEG image file.  
SMS  
E-mail in SMS format to an e-mail-to-SMS gateway (for example to send an alarm by  
cellphone) without an image attachment.  
CAUTION!  
When a cellphone is used as the receiver, make sure to activate the e-mail or SMS function,  
depending on the format, so that these messages can be received.  
You can obtain information on operating your cellphone from your cellphone provider.  
Attach JPEG from camera  
Click the checkbox to specify that JPEG images are sent from the camera. An enabled video  
input is indicated by a check mark.  
Destination address  
Enter the e-mail address for alarm e-mails here. The maximum address length is 49  
characters.  
Sender name  
Enter a unique name for the e-mail sender, for example the location of the unit. This will make  
it easier to identify the origin of the e-mail.  
Test e-mail  
You can test the e-mail function by clicking the Send Now button. An alarm e-mail is  
immediately created and sent.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en 103  
7.43  
Alarm Task Editor  
CAUTION!  
Editing scripts on this page overwrites all settings and entries on the other alarm pages. This  
procedure cannot be reversed.  
In order to edit this page, you must have programming knowledge and be familiar with the  
information in the Alarm Task Script Language document.  
As an alternative to the alarm settings on the various alarm pages, you can enter your desired  
alarm functions in script form here. This will overwrite all settings and entries on the other  
alarm pages.  
1. Click the Examples link under the Alarm Task Editor field to see some script examples. A  
new window will open.  
2. Enter new scripts in the Alarm Task Editor field or change existing scripts in line with  
your requirements.  
3. When you are finished, click the Set button to transmit the scripts to the unit. If the  
transfer was successful, the message Script successfully parsed is displayed over the  
text field. If it was not successful, an error message will be displayed with further  
information.  
7.44  
Alarm Rules  
The AutoDome 800 Series features an alarm rule engine. In its simplest form, an alarm rule  
can define which input(s) activate which output(s). Basically, an alarm rule allows you to  
customize an AutoDome 800 Series to automatically respond to different alarm inputs.  
To configure an alarm rule specify one input from either a physical connection, a motion  
detection trigger, or from a connection to the camera’s Livepage. The physical input  
connection can be activated by dry contact devices such as pressure pads, door contacts and  
similar devices  
Next, specify up to two (2) rule outputs, or the camera’s response to the input. Outputs  
include a physical alarm relay, an AUX command, or a preposition scene.  
1. Click the Enabled check box to activate the alarm.  
2. Choose one of the following alarm inputs:  
–
–
–
–
Local Input 1: a physical alarm connection.  
Local Input 2: a physical alarm connection.  
IVA/MOTION+: an alarm when IVA or motion detection is activated.  
Connection: an alarm when an attempt is made to access the camera’s IP address.  
Bosch Security Systems, Inc.  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
F.01U.273.797 | 5.0 | 2012.08  
104 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
3. Choose one of the following output commands for both Output 1 and Output 2 settings:  
–
–
–
None: no defined command.  
Alarm Relay: defines a physical connection from the open collector alarm output.  
Aux On: defines a standard or custom keyboard ON command.  
Refer to Section A Keyboard Commands by Number, page 116, for a list of valid com-  
mands.  
Note: Only commands 1, 2, 8, 18, 20, 43, 60, 78, 80, 86 are supported. Support for  
the remaining commands is scheduled for a future release.  
–
Aux Off: defines a standard or custom keyboard OFF command.  
Refer to Section A Keyboard Commands by Number, page 116, for a list of valid com-  
mands.  
Note: Only commands 1, 2, 8, 18, 20, 43, 60, 78, 80, 86 are supported. Support for  
the remaining commands is scheduled for a future release.  
–
Shot: defines a preset scene from shot 1-99.  
4. Click Set to save and to activate the alarm rules.  
7.45  
7.46  
Advanced Mode: Interfaces  
Alarm Inputs  
Select the type of input for each physical alarm. Select from either N.O. (Normally Open) or  
N.C. (Normally Closed) and provide an optional name for each input.  
7.47  
Relay  
You can configure the switching behavior of the relay outputs. For each relay, you can specify  
an open switch relay (normally closed contact) or a closed switch relay (normally open  
contact).  
You can also specify whether an output should operate as a bistable or monostable relay. In  
bistable mode, the triggered state of the relay is maintained. In monostable mode, you can set  
the time after which the relay will return to the idle state.  
You can select different events that automatically activate an output. It is possible, for  
example, to turn on a floodlight by triggering a motion alarm and then turning the light off  
again when the alarm has stopped.  
Idle State  
Select Open if you want the relay to operate as an NO contact, or select Closed if the relay is  
to operate as an NC contact.  
Operating Mode  
Select an operating mode for the relay.  
For example, if you want an alarm-activated lamp to stay on after the alarm ends, select  
Bistable. If you wish an alarm-activated siren to sound for ten seconds, for example, select  
10 s.  
Relay Follows  
Select one of the following actions that the AutoDome performs after the relay is triggered:  
–
–
–
–
–
Off  
Connection  
Video Alarm 1  
Motion Alarm 1  
Local Input 1  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en 105  
–
Remote Input 1  
Relay Name  
You can assign a name for the relay here. The name is shown on the button next to Trigger  
relay. The Livepage can also be configured to display the name under the relay icon. You can  
also use the name in the Forensic Search program function as a filter option for quick search  
in recordings. Enter a unique and clear name here.  
CAUTION!  
Do not use any special characters, for example &, in the name.  
Trigger Relay  
Click the Relay 1 button to test the relay connection.  
7.48  
7.49  
Advanced Mode: Network  
Network Access  
The settings on this page are used to integrate the AutoDome 800 Series into an existing  
network.  
Some changes only take effect after the unit is rebooted. In this case, the Set button changes  
to Set and Reboot.  
1. Make the desired changes.  
2. Click the Set and Reboot button. The AutoDome 800 Series is rebooted and the changed  
settings are activated.  
CAUTION!  
If you change the IP address, subnet mask or gateway address, the AutoDome 800 Series is  
only available under the new addresses after the reboot.  
Automatic IP assignment  
If a DHCP server is employed in the network for the dynamic assignment of IP addresses, you  
can activate acceptance of IP addresses automatically assigned to the AutoDome 800 Series.  
Certain applications (VIDOS, Bosch Video Management System, Archive Player, Configuration  
Manager) use the IP address for the unique assignment of the unit. If you use these  
applications, the DHCP server must support the fixed assignment between IP address and  
MAC address, and must be appropriately set up so that, once an IP address is assigned, it is  
retained each time the system is rebooted.  
7.49.1  
IPv4  
IP address  
Enter the desired IP address for the AutoDome 800 Series in this field. The IP address must  
be valid for the network.  
Subnet mask  
Enter the appropriate subnet mask for the selected IP address here.  
Gateway address  
If you want the unit to establish a connection to a remote location in a different subnet, enter  
the IP address of the gateway here. Otherwise leave the box blank (0.0.0.0).  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
106 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
7.49.2  
IPv6  
Consult with the network administrator before making changes to the this section.  
IP Address  
Enter the desired IP address for the AutoDome 800 Series in this field. The IP address must  
be valid for the network. A typical IPv6 address may resemble the following example:  
2001:db8 : : 52:1:1  
Consult the network administrator for valid IPv6 address construction.  
Prefix Length  
A typical IPv6 node address consists of a prefix and an interface identifier (total 128 bits). The  
prefix is the part of the address where the bits have fixed values or are the bits that define a  
subnet.  
Gateway Address  
If you want the unit to establish a connection to a remote location in a different subnet, enter  
the IP address of the gateway here. Otherwise leave the box blank (0.0.0.0).  
7.49.3  
Detailed Settings  
DNS server address  
The AutoDome 800 Series is easier to access if the unit is listed on a DNS server. If you wish,  
for example, to establish an Internet connection to the AutoDome 800 Series, it is sufficient to  
enter the name given to the unit on the DNS server as a URL in the browser. Enter the IP  
address of the DNS server here. Servers are supported for secure and dynamic DNS.  
Video Transmission  
If the unit is operated behind a firewall, TCP (HTTP port) should be selected as the transfer  
protocol. For use in a local network, select UDP.  
CAUTION!  
Multicast operation is only possible with the UDP protocol. The TCP protocol does not  
support multicast connections.  
The MTU value in UDP mode is 1,514 bytes.  
HTTP browser port  
Select a different HTTP browser port from the list if required. The default HTTP port is 80. If  
you want to allow only secure connections via HTTPS, you must deactivate the HTTP port. In  
this case, select Off.  
HTTPS browser port  
If you wish to allow browser access on the network via a secure connection, select an HTTPS  
browser port from the list if necessary. The default HTTPS port is 443. Select the Off option  
to deactivate HTTPS ports; only unsecured connections will now be possible.  
The AutoDome 800 Series uses the TLS 1.0 encryption protocol. You may have to activate this  
protocol via your browser configuration. You must also activate the protocol for the Java  
applications (via the Java control panel in the Windows control panel).  
NOTICE!  
If you want to allow only secure connections with SSL encryption, you must select the Off  
option for each of the parameters HTTP browser port, RCP+ port 1756 and Telnet support.  
This deactivates all unsecured connections. Connections will then only be possible via the  
HTTPS port.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en 107  
You can activate and configure encryption of the media data (video and metadata) on the  
Encryption page (see Section 7.54 Encryption, page 111).  
RCP+ port 1756  
To exchange connection data, you can activate the unsecured RCP+ port 1756. If you want  
connection data to be transmitted only when encrypted, select the Off option to deactivate  
the port.  
Telnet support  
If you want to allow only secure connections with encrypted data transmission, you must  
select the Off option to deactivate Telnet support. The unit will then no longer be accessible  
using the Telnet protocol.  
Interface mode ETH  
If necessary, select the Ethernet link type for the ETH interface. Depending on the unit  
connected, it may be necessary to select a special operation type.  
Network MSS (Byte)  
You can set the maximum segment size for the IP packet's user data. This gives you the option  
to adjust the size of the data packets to the network environment and to optimize data  
transmission. Please comply with the MTU value of 1,514 bytes in UDP mode.  
iSCSI MSS (Byte)  
You can specify a higher MSS value for a connection to the iSCSI system than for the other  
data traffic via the network. The potential value depends on the network structure. A higher  
value is only useful if the iSCSI system is located in the same subnet as the AutoDome 800  
Series.  
Enable DynDNS  
DynDNS.org is a DNS hosting service that stores IP addresses in a database ready for use. It  
allows you to select the AutoDome 800 Series via the Internet using a host name, without  
having to know the current IP address of the unit. You can enable this service here. To do this,  
you must have an account with DynDNS.org and you must have registered the required host  
name for the unit on that site.  
NOTICE!  
Information about the service, registration process and available host names can be found at  
DynDNS.org.  
Host name  
Enter the host name registered on DynDNS.org for the AutoDome 800 Series here.  
User name  
Enter the user name you registered at DynDNS.org here.  
Password  
Enter the password you registered at DynDNS.org here.  
Force registration now  
You can force the registration by transferring the IP address to the DynDNS server. Entries  
that change frequently are not provided in the Domain Name System. It is a good idea to force  
the registration when you are setting up the device for the first time. Only use this function  
when necessary and no more than once a day, to avoid the possibility of being blocked by the  
service provider. To transfer the IP address of the AutoDome 800 Series, click the Register  
button.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
108 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
Status  
The status of the DynDNS function is displayed here for information purposes. You cannot  
change any of these settings.  
7.50  
Advanced  
The settings on this page are used to implement advanced settings for the network.  
Some changes only take effect after the unit is rebooted. In this case, the Set button changes  
to Set and Reboot.  
1. Make the desired changes.  
2. Click the Set and Reboot button. The AutoDome 800 Series is rebooted and the changed  
settings are activated.  
SNMP  
The AutoDome 800 Series supports the SNMP V2 (Simple Network Management Protocol) for  
managing and monitoring network components, and can send SNMP messages (traps) to IP  
addresses. The unit supports SNMP MIB II in the unified code. If you wish to send SNMP  
traps, enter the IP addresses of one or two required target devices here.  
If you select On for the SNMP parameter and do not enter an SNMP host address, the  
AutoDome 800 Series does not send them automatically, but only replies to SNMP requests. If  
you enter one or two SNMP host addresses, SNMP traps are sent automatically. Select Off to  
deactivate the SNMP function.  
1. SNMP host address / 2. SNMP host address  
If you wish to send SNMP traps automatically, enter the IP addresses of one or two required  
target units here.  
SNMP traps  
You can select which traps are to be sent.  
1. Click Select. A list is opened.  
2. Click the checkboxes to select the required traps. All the checked traps will be sent.  
3. Click Set to accept the selection.  
Authentication  
If a RADIUS server is employed in the network for managing access rights, authentication  
must be activated here to allow communication with the unit. The RADIUS server must also  
contain the corresponding data.  
To configure the unit, you must connect the AutoDome 800 Series directly to a computer  
using a network cable. This is because communication via the network is not enabled until the  
Identity and Password parameters have been set and successfully authenticated.  
Identity  
Enter the name that the RADIUS server is to use for identifying the AutoDome 800 Series.  
Password  
Enter the password that is stored in the RADIUS server.  
RTSP port  
If necessary, select a different port for the exchange of the RTSP data from the list. The  
standard RTSP port is 554. Select Off to deactivate the RTSP function.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en 109  
NTCIP  
Specifies a set of rules and protocols for organizing, describing and exchanging transportation  
management information between transportation management applications and  
transportation equipment such that they interoperate with each other.  
Select a port for NTCIP and the Address from the appropriate drop-down lists.  
UPnP  
You can activate the Universal Plug and Play (UPnP) function. If the function is turned on, the  
unit responds to requests from the network and is automatically registered on the requesting  
computers as a new network device. For example, access to the unit can then be made using  
Windows Explorer without knowledge of the IP address of the unit.  
NOTICE!  
To use the UPnP function on a computer, both the Universal Plug and Play Device Host and  
SSDP Discovery Service must be active in Windows XP and Windows 7.  
TCP Port  
The device can receive data from an external TCP sender, for example an ATM or POS device,  
and store it as metadata. Select the port for TCP communication. Select Off to deactivate the  
TCP metadata function.  
Sender IP address  
Enter the IP address of the TCP metadata sender here.  
Quality of Service  
The AutoDome offers Quality of Service (QoS) configuration options to ensure fast network  
response to PTZ data and images. Quality of Service (QoS) is the set of techniques to manage  
network resources. QoS manages the delay, delay variation (jitter), bandwidth, and packet  
loss parameters to guarantee the ability of a network to deliver predictable results. QoS  
identifies the type of data in a data packet and divides the packets into traffic classes that can  
be prioritized for forwarding.  
Consult with your network administrator for assistance configuring the Audio, Video, Control,  
and the Alarm Video settings.  
7.51  
Multicast  
In addition to a 1:1 connection between an encoder and a single receiver (unicast), the  
AutoDome 800 Series can enable multiple receivers to receive the video signal from an  
encoder simultaneously. The device either duplicates the data stream itself and then  
distributes it to multiple receivers (Multi-unicast) or it sends a single data stream to the  
network, where the data stream is simultaneously distributed to multiple receivers in a  
defined group (Multicast). You can enter a dedicated multicast address and port for each  
stream. You can switch between the streams by clicking the appropriate tabs.  
NOTICE!  
Multicast operation requires a multicast-enabled network that uses the UDP and the Internet  
Group Management IGMP protocols. Other group management protocols are not supported.  
The TCP protocol does not support multicast connections.  
A special IP address (class D address) must be configured for multicast operation in a  
multicast-enabled network.  
The network must support group IP addresses and the Internet Group Management Protocol  
(IGMP V2). The address range is from 225.0.0.0 to 239.255.255.255.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
110 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
The multicast address can be the same for multiple streams. However, it will be necessary to  
use a different port in each case so that multiple data streams are not sent simultaneously  
using the same port and multicast address.  
NOTICE!  
The settings must be made individually for each stream.  
Enable  
To enable simultaneous data reception on several receivers you need to activate the multicast  
function. To do this, check the box. You can then enter the multicast address.  
Multicast Address  
Enter a valid multicast address for each stream to be operated in multicast mode (duplication  
of the data streams in the network).  
With the setting 0.0.0.0 the encoder for the relevant stream operates in multi-unicast mode  
(copying of data streams in the unit). The AutoDome 800 Series supports multi-unicast  
connections for up to five simultaneously connected receivers.  
NOTICE!  
Duplication of data places a heavy demand on the unit and can lead to impairment of the  
image quality under certain circumstances.  
Port  
Assign a different port to each data stream if there are simultaneous data streams at the same  
multicast address.  
Enter the port address of the required stream here.  
Streaming  
Click the checkbox to activate multicast streaming mode for the relevant stream. An enabled  
stream is indicated by a check mark.  
Multicast packet TTL  
You can enter a value to specify how long the multicast data packets are active on the  
network. This value must be greater than one if multicast is to be run via a router.  
7.52  
FTP Posting  
You can save individual JPEG images on an FTP server at specific intervals. You can then  
retrieve these images at a later date to reconstruct alarm events if required.  
File name  
You can select how file names will be created for the individual images that are transmitted.  
–
–
–
Overwrite  
The same file name is always used and any existing file will be overwritten with the  
current file.  
Increment  
A number from 000 to 255 is added to the file name and automatically incremented by 1.  
When it reaches 255 it starts again from 000.  
Date/time suffix  
The date and time are automatically added to the file name. When setting this parameter,  
ensure that the unit's date and time are always correctly set. Example: the file  
snap011005_114530.jpg was stored on October 1, 2005 at 11:45 and 30 seconds.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en 111  
Posting interval  
Enter the interval in seconds at which the images will be sent to an FTP server. Enter zero if  
you do not want any images to be sent.  
FTP server IP address  
Enter the IP address of the FTP server on which you wish to save the JPEG images.  
FTP server login  
Enter your login name for the FTP server.  
FTP server password  
Enter the password that gives you access to the FTP server.  
Path on FTP server  
Enter the exact path on which you wish to post the images on the FTP server.  
Max. Bit Rate  
Enter the maximum bit rate for the JPEG images.  
7.53  
7.54  
IPv4 Filter  
Use this setting to configure a filter that allows or blocks network traffic that matches a  
specified address or protocol.  
IP Address 1 / 2  
Enter the IPv4 address that you want to allow or block  
Mask 1 / 2  
Enter the subnet mask for the appropriate IPv4 address.  
Encryption  
A special license, with which you will receive a corresponding activation key, is required to  
encrypt user data. You can enter the activation key to release the function on the Licenses  
page (see Section 7.57 Licenses, page 112).  
7.55  
7.56  
Advanced Mode: Service  
Maintenance  
Firmware  
The AutoDome 800 Series is designed in such a way that its functions and parameters can be  
updated with firmware. To do this, transfer the current firmware package to the unit via the  
selected network. It will then be automatically installed there.  
In this way, an AutoDome 800 Series can be serviced and updated remotely without a  
technician having to change the installation on site.  
Refer to Section 9 BVIP Firmware Updates, page 115, for firmware upgrade instructions.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
112 en | Configuring the AutoDome 800 Series  
AutoDome 800 Series HD PTZ Camera  
CAUTION!  
Before launching the firmware upload make sure that you have selected the correct upload  
file. Uploading the wrong files can result in the unit no longer being addressable, in which  
case you must replace the unit.  
You should never interrupt the installation of firmware. An interruption can lead to the flash-  
EPROM being incorrectly programmed. This in turn can result in the unit no longer being  
addressable, in which case it will have to be replaced. Even changing to another page or  
closing the browser window leads to an interruption.  
Refer to Section 9 BVIP Firmware Updates, page 115, for firmware upgrade instructions.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Configuring the AutoDome 800 Series | en 113  
Configuration  
You can save configuration data for the AutoDome 800 Series on a computer and then load  
saved configuration data from a computer to the unit.  
Upload  
1. Enter the full path of the file to upload or click Browse to select the required file.  
2. Make certain that the file to be loaded comes from the same unit type as the unit you  
want to configure.  
3. Next, click Upload to begin transferring the file to the unit. The progress bar allows you  
to monitor the transfer.  
Once the upload is complete, the new configuration is activated. The time remaining is shown  
by the message going to reset Reconnecting in ... seconds. The unit reboots automatically  
once the upload has successfully completed.  
Download  
1. Click the Download button. A dialog box opens.  
2. Follow the on-screen instructions to save the current settings.  
SSL certificate  
To be able to work with an SSL encrypted data connection, both ends of a connection must  
hold the relevant certificates. You can upload the SSL certificate, comprising one or multiple  
files, onto the AutoDome 800 Series.  
If you wish to upload multiple files onto the AutoDome 800 Series, you must select them  
consecutively.  
1. Enter the full path of the file to upload or click Browse to select the required file.  
2. Next, click Upload to begin transferring the file to the unit.  
3. Once all files have been successfully uploaded, the unit must be rebooted. In the address  
bar of your browser, enter /reset after the IP address of the AutoDome 800 Series (for  
example 192.168.0.10/reset).  
The new SSL certificate is valid.  
Maintenance log  
You can download an internal maintenance log from the unit to send it to Customer Service  
for support purposes. Click Download and select a storage location for the file.  
7.57  
7.58  
Licenses  
You can enter the activation key to release additional functions or software modules.  
NOTICE!  
The activation key cannot be deactivated again and is not transferable to other units.  
System Overview  
The data on this page are for information purposes only and cannot be changed. Keep a  
record of this information in case technical assistance is required.  
NOTICE!  
You can select all required text on this page with the mouse and copy it to the clipboard with  
the [Ctrl]+[C] key combination, for example if you want to send it via e-mail.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Bubble Handling and Cleaning | en 113  
8
Bubble Handling and Cleaning  
The bubble is made of acrylic for excellent optical clarity. Special care is required when  
handling and cleaning the bubble to avoid scratching it.  
8.1  
Handling  
The bubble is packaged with a protective plastic sheet. It is recommended that the bubble  
remain stored this way until it is ready to install. Limit handling the bubble, as any scratches  
can quickly affect visibility.  
8.2  
Cleaning  
If cleaning the bubble is required, use the following procedures and comply with all the  
warnings listed below.  
8.2.1  
Cleaning the Bubble Interior  
The extremely soft interior surface should not be cleaned by rubbing or dusting with a cloth.  
Use clean dry compressed air, preferably from a spray can, to remove any dust from the  
interior surface.  
WARNING!  
Do not use alcohol-based solutions to clean the bubble. This will cause the bubble to cloud  
and over time cause stress aging, which makes the bubble brittle.  
Removing the Pendant Bubble  
Use the following procedure to remove the bubble:  
1. Using both hands, apply a counterclockwise (looking up at the dome) rotational force on  
the Pendant Bubble Assembly to set the bubble latch.  
2. Insert a small (2 mm) straight blade screwdriver into the latch opening of the bubble  
trim-ring to release the latch. Then remove the screwdriver. See the figure below.  
Figure 8.1 Pendant Bubble Release Opening  
3. Rotate the bubble assembly counterclockwise approximately 20 degrees until the bubble  
assembly releases from the pendant housing and remove the bubble.  
4. To replace the bubble, insert the bubble assembly into the pendant housing, and rotate it  
clockwise (looking up at the dome) until it locks. The latch mechanism makes a click  
when it locks.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
114 en | Bubble Handling and Cleaning  
AutoDome 800 Series HD PTZ Camera  
8.2.2  
Cleaning the Bubble Exterior  
The exterior of the bubble is hard coated for extra protection. If cleaning becomes necessary,  
only use cleaning solutions and cloths suitable for cleaning safety glass lenses. Dry the bubble  
thoroughly with a dry nonabrasive cloth to prevent water spots. Never scrub the bubble with  
any abrasive material or cleaners.  
Do Not:  
–
–
–
–
Do Not use abrasive or highly alkaline cleaners on the bubble.  
Do Not scrape the bubble with razor blades or other sharp instruments.  
Do Not use Benzene, Gasoline, Acetone, or Carbon Tetrachloride on the bubble.  
Do Not clean bubbles in the hot sun or on very hot days.  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
BVIP Firmware Updates | en 115  
9
BVIP Firmware Updates  
The AutoDome 800 Series incorporate a network video server in the IP module. The primary  
function of the server is to encode video and control data for transmission over a TCP/IP  
network. The AutoDome 800 Series also allows an operator to update the BVIP firmware via  
the TCP/IP network.  
The latest BVIP firmware is available on the Bosch Security Systems Web site. To download  
the service pack from the Web, navigate to www.boschsecurity.us, click the CCTV link, then  
click Cameras, PTZ and navigate to the product page for the AutoDome 800 Series. Then click  
the Software tab on the product page.  
9.1  
9.2  
Upgrading the AutoDome 800 Series  
The preferred method to update an AutoDome 800 Series is through a direct connection  
between the camera and a PC. This method entails connecting the Ethernet cable from the  
camera directly to the Ethernet port of a PC.  
If the direct-connect method is not practical you can also update the AutoDome 800 Series  
through a Local Area Network (LAN). You cannot, however, update the AutoDome 800 Series  
through a Wide Area Network (WAN) or via the Internet.  
Beginning the Firmware Update Process  
Use this procedure to connect to your AutoDome 800 Series and to navigate to the Firmware  
Update page.  
1. Launch Internet Explorer and type the IP address for the AutoDome 800 Series in the  
Address bar and click Go.  
Internet Explorer opens the Livepage view.  
2. Click the SETTINGS link, located at the top of the page.  
3. Click the Service link in the left pane.  
4. Click the Maintenance link below the Service link.  
5. Click the Search button and navigate to the firmware file (*.fw). Then, click OK.  
6. Click the Upload button.  
7. Click OK to the warning message to continue the firmware upload, or Cancel to stop the  
upload.  
The page displays a progress bar as the firmware is uploaded.  
Note: Once the progress bar reaches 100% the system opens the reset page. Allow the  
reset page to complete its action.  
8. Once the reset is complete the upgrade is complete.  
Bosch Security Systems, Inc.  
Installation Manual  
F.01U.273.797 | 5.0 | 2012.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
116 en |  
AutoDome 800 Series HD PTZ Camera  
A
Keyboard Commands by Number  
Locked Alarm Rule  
Output  
Function Key  
Comm No. Command  
Description  
Y
On/Off  
On/Off  
On/Off  
On/Off  
On/Off  
On/Off  
1
Scan 360°  
Autopan without limits  
Autopan between limits  
Activate/Deactivate  
2
Autopan  
Y
8
Play Pre-position Tour  
AutoPivot Enable  
Backlight Comp  
Y
Y
Y
18  
20  
40  
Enables/disables AutoPivot  
Backlight Compensation  
Y
Y
Restore Camera Settings Restores all setting to their original  
defaults  
Y
On/Off  
On/Off  
On/Off  
On/Off  
43  
50  
52  
57  
Auto Gain Control  
Playback Tour A  
Playback Tour B  
Night Mode setting  
AGC–On, Auto, Off  
Activate/Deactivate  
Activate/Deactivate  
Y
Y
Y
Enables/Disables Night Mode (Day/Night  
only)  
Y
Y
On/Off  
On/Off  
60  
78  
On Screen Display  
Intelligent Tracking  
On–enable  
Off–disable  
Turns Intelligent Tracking on or off. Refer  
to Section 6.5 Configuring Intelligent  
Tracking, page 60, configuration steps.  
Y
Y
Y
Y
On/Off  
On/Off  
80  
86  
Digital Zoom Lock  
Sector Blanking  
Turns digital zoom on and off  
On–enable  
Off–disable  
Y
Y
Y
On/Off  
On/Off  
87  
90  
Privacy Masking  
On–enable  
Off–disable  
Command Lock/Unlock  
On–lock on  
Off–lock off  
Y
On/Off  
On/Off  
94  
95  
Set Azimuth Zero Point  
Sets the zero degree pan position.  
Display Azimuth/  
On–Displays azimuth/elevation readings  
Off–Hides azimuth/elevation readings  
Elevation Readings  
On/Off  
On/Off  
On/Off  
96  
Display Compass  
Heading  
On–Displays compass heading  
Off–Hides compass heading  
100  
101  
Record Tour A  
On– start recording  
Off – stop recording  
Record Tour B  
On– start recording  
Off – stop recording  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AutoDome 800 Series HD PTZ Camera  
Index | en 117  
Index  
commands  
/reset 60  
Symbols  
/reset 60  
Aux Off 64  
Aux On 64  
A
activating the recording 95  
activation key 112  
keyboard 64, 116  
preset shot 64  
alarm 77  
alarm e-mail 102  
alarm inputs 54  
Set Shot 64  
Show Shot 64  
configuration download 112  
Configuration Manager 59  
configuration mode 70  
configuring  
non-supervised 54  
normally closed non-supervised 54  
normally open non-supervised 54  
with parapet roof or pipe mounts 47  
with pendant arm, corner or mast mount 18, 24, 29  
alarm message 77  
/reset 60  
IP network settings 59  
Livepage 59  
alarm outputs 55  
connect on alarm 95  
control signals 78  
controlling  
open collector output 55  
with parapet roof or pipe mount 47  
with pendant arm, corner or mast mount 18, 24, 29  
alarm rule 103  
alarm sensors 93  
attaching  
cover door 36  
pendant arm 22  
audio settings 73, 90  
audio transmission 73, 90  
auto-connect 97  
image area 63  
copper wire 51  
corner installation 16, 26  
corner plate 16  
cover door 36  
D
date 75  
date format 75  
daylight saving time 75  
default profile 82  
default recording profile 92  
default VCA profile 97  
deleting recordings 92  
device ID 74  
device name 70  
DHCP server 72  
Dibos 56  
AutoPivot 87  
Aux Control tab 64  
Aux Off 64  
Aux On 64  
azimuth zero 88  
B
banding tool 15, 16, 26  
basic mode 70  
BNC connector  
DirectX 57  
with pendant arm, corner or mast mount 18  
with roof parapet or pipe mount 47  
Browser window 61  
bubble 113  
Display stamping 61  
display stamping 76  
displaying  
on-screen menus 64  
dome cap 44  
dual streaming 56, 80  
DynDNS 107  
cleaning 113  
handling 113  
C
cable  
E
Ethernet 57  
cable standards 51  
cables  
copper 51  
camera  
selection 62  
camera name 74  
changes in light level 98  
command numbers 64  
e-mail 102  
encoding 56  
video 56  
encryption protocol 106  
EPROM 111  
Ethernet 51  
cable 60  
event log 63, 79  
F
false alarms 98  
fiber optic  
module 25  
single mode 51  
with pendant arm, corner or mast mount 18  
with roof parapet or pipe mount 39  
Bosch Security Systems, Inc.  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
F.01U.273.797 | 5.0 | 2012.08  
118 en | Index  
AutoDome 800 Series HD PTZ Camera  
files  
JPEG posting 110  
JPEG 56  
JPEG posting interval 110  
MPEG-4 56  
K
firewall 96, 106  
firmware upload 111  
formatting 92  
FTP server 110, 111  
fuse specifications 19  
keyboard commands 64, 116  
Aux Off command 64  
Aux On 64  
keypad 64  
L
G
language 78  
licenses 112  
Livepage 59  
livepage 78  
LTC 9230/01 43  
gateway 72, 105, 106  
gateway address 58  
general password 96  
guard tour 88  
guy-wire 45  
M
H
manufacturer logo 77  
mast installation 16, 26  
mast plate 16  
holidays 94  
HTTP port 106  
HTTPS port 106  
milliseconds 77  
I
motion detector 97  
motion detector defaults 97  
motion detector object size 98  
motion detector sensitivity 98, 99  
mount  
identification 70  
IEEE 802.1x 108  
IGMP 109  
IGMP V2 56  
image quality 110  
image resolution 66  
image selection 62  
inactivity 87  
pendant arm, corner or mast 14  
pipe 33  
roof parapet 33  
Mouting Plate 15, 26  
initiator name 74  
MPEG ActiveX 57  
installing  
MPEG-4 56  
pendant arm, corner or mast mount 14  
pipe interface board 48  
pipe mount 45  
MTU value 106, 107  
multicast 56  
multicast address 110  
multicast connection 106, 109  
multicasting 109  
roof parapet mount 42  
tope-mounting flange 45  
Intelligent Tracking 60, 65  
field of view recommendations 61  
mount recommendations 61  
internal clock 75  
IP 56  
multi-unicast 109  
N
navigation 70  
NEMA Certification  
for pendant arm, corner or mast mount 15  
for roof parapet or pipe mount 34  
network 72, 105, 108  
network settings page 59  
networking  
/reset 60  
address 58, 59, 72  
alarm 63  
dual streaming 56  
encoding 56  
gateway address 58  
Livepage 59  
module 56  
multicast 56  
network settings page 59  
port 58  
record 56  
snapshots 56  
Ethernet cable 57  
gateway address 58  
IGMP V2 56  
IP 56  
IP address 58  
NTCIP 108  
port 58  
QoS 109  
RTSP 108  
subnet mask 58  
TCP port 109  
TCP/IP 56  
UDP 56  
UPnP 109  
subnet mask 58  
system requirements 56  
IP address 105, 106  
IPv4 105  
IPv6 106  
iSCSI settings 91  
non-supervised alarms 54  
NTCIP 108  
number of connections 62  
J
JPEG 56  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
AutoDome 800 Series HD PTZ Camera  
Index | en 119  
roof parapet or pipe mount 33, 42  
cover door 36  
P
parapet arm  
dome cap 44  
parts 33  
power supply box location 34  
wall bracket 43  
stabilizing 45  
password 62, 71, 74, 75  
pendant  
connector harness 25, 30  
pendant arm  
attaching to power supply box 22  
pendant arm, corner or mast mount  
mast plate 16  
pendant assembly  
attaching to pipe mount 49  
pendant bubble  
wall mount bracket 42  
router 110  
routing wires  
for pendant arm, corner or mast mount 17  
for roof parapet or pipe mount 37  
RTSP port 108  
S
removing 113  
saving event log 79  
saving system log 79  
savng configuration 112  
select area 99, 101  
selecting a profile 80  
sensor fields 99, 100  
Set Shot 64  
pipe interface board 46, 48  
pipe mount 33, 45  
power supply box location 34  
pole installation 16, 26  
port 58, 106, 110  
post-alarm profile 93  
post-alarm time 93  
Show Shot command 64  
SMS 102  
power supply  
fuse specifications 19  
power supply box 37  
attaching to pendant arm 22  
connections for pendant arm 20, 21, 42  
connections for roof parapet or pipe mount 33, 41  
installing with pendant arm, corner or mast mount  
16, 23  
snapshots 56, 66  
SNMP 108  
SNTP server 71, 76  
software  
DirectX 57  
SSL certificate 112  
SSL encryption 97  
standard recording profile values 92  
storage media 91  
storage medium 73, 74, 91  
streaming 110  
installing with roof parapet or pipe mount 34  
locating for pendant arm, corner or mast mount 15  
wiring for pendant arm, corner or mast mount 23  
pre-alarm time 93  
prefix length 106  
preposition 89  
subnet mask 58, 72, 105  
summer time 75  
preset 89  
preset shot 64  
processor load 66  
processor load indicator 66  
product name 77  
synchronize 71, 75  
system log 63, 79  
T
tamper detection 99  
target data rate 81  
TCP 96, 106  
profile configuration 81  
profiles 72, 80  
TCP port 109  
TCP/IP 56  
protocol  
IGMP V2 56  
TCP/IP 56  
UDP 56  
time 71, 75, 76  
time server 71, 76  
IP address 71  
protocol 71  
time server IP address 76  
time server protocol 76  
time signal 71, 76  
time zone 75  
Q
QoS 109  
quality of service 109  
R
RADIUS 108  
TLS 106  
top-mounting flange 45  
tour  
receiver password 95  
record 56  
recorded tour 88  
recording media 91  
recording profiles 92  
recording scheduler 94  
recording status 95  
recording video sequences 66  
reflections of light 98  
relay 55  
guard 88  
preposition 89  
recorded 88  
transmission protocol 96, 106  
traps 108  
trim skirt 16  
TTL 110  
Bosch Security Systems, Inc.  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
F.01U.273.797 | 5.0 | 2012.08  
120 en | Index  
AutoDome 800 Series HD PTZ Camera  
U
UDP 56, 96, 106  
unicast 109  
unit date 75  
unit identification 70  
unit name 70  
unit time 71, 75  
unshielded twisted pair  
with pendant arm, corner or mast mount 18  
UPnP 109  
user name 71, 75  
UTP CAT-5 51  
V
VG4-A-9230 33, 42  
VG4-ARMPLATE 15, 26  
video content analysis 97  
video sensor 97  
VIDOS 56  
VIP XD 56  
VRM 91  
W
wall installation 16  
wall mount template 16  
for roof parapet or pipe mount 35  
watermarking 77  
wire standards 51  
wiring  
for pendant arm, corner or mast mount 15  
for pipe interface board 46  
for roof parapet or pipe mount 39  
power supply box 37  
F.01U.273.797 | 5.0 | 2012.08  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bosch Security Systems, Inc.  
850 Greenfield Road  
Lancaster, PA 17601  
U.S.A.  
www.boschsecurity.com  
© Bosch Security Systems, Inc., 2012  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Blue Rhino Charcoal Grill 253341 User Manual
Breville Espresso Maker ESP6 8 User Manual
Breville Rice Cooker RC16XL User Manual
Caframo Fan Chinook User Manual
Califone Camcorder Accessories TP 30 User Manual
Cambridge Audio CD Player CD30 User Manual
Canon Camcorder 6340B002 User Manual
Carrier Thermostat TCSNAC01 User Manual
Chamberlain Home Security System CWA2000 User Manual
Chaparral Network Router VFS113 User Manual