DX4010i
Installation Instructions
RS-232 Serial Interface
EN Module
Download from Www.Somanuals.com. All Manuals Search And Download.
DX4010i | Installation Instructions | Contents
Contents
1.0
2.0
3.0
4.0
5.0
5.1
5.2
5.3
6.0
7.0
8.0
General Information .......................................4
Specifications ....................................................4
Installation Standards .....................................4
Wiring.................................................................5
DX4010i Jumper Pin Settings ........................6
Enable LED Jumper Pins (P2)...........................6
DB9 Ground Enable Pins (P1)..........................6
Address DIP Switches........................................7
Remote Programming Direct Connection .7
DB9 DTE RS-232 Connector (P6)................10
RJ-16 Data Bus Connector (P3)....................11
Figures
Figure 1:
Figure 2:
Figure 3:
Figure 4:
Figure 5:
Figure 6:
Figure 7:
Figure 8:
Figure 9:
DX4010i PCB Layout.................................4
Control Panel Connections........................5
External Power Supply Connections ........5
Serial Device Connections .........................5
Parallel Device Connections......................6
P2 Jumper Settings ......................................6
DIP Switch Location/Orientation .............7
DB9 Connector Layout ............................10
P3 Connector.............................................11
Tables
Table 1:
Table 2:
Table 3:
Table 4:
Table 5:
DX4010i Specifications...............................4
Diagnostic LED Functions .........................6
Option Bus Address DIP Switch Settings.8
SDI Bus Address DIP Switch Settings ......9
Alternate Wiring Configuration...............10
Bosch Security Systems, Inc. | 1/05 | 4998141106C
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DX4010i | Installation Instructions | 1.0 General Information
1.0 General Information
Figure 1: DX4010i Component Layout
The DX4010i is a data terminal equipment (DTE)
configured RS-232 serial device interface (SDI) module
designed to operate with compatible control panels. It
connects to the control panel through the option or
SDI data bus.
5
6
LED
NABLE
E
RxTx
BUS
TxR x
SER
P2
P6
4
7
The DX4010i is used to connect a PC with RPS, BIS,
PC 9000, CMS 7000, or other third party software that
uses a serial conncetion to the supported control
panels. The module also supports a serial printer (or
parallel printer with a convertor box) for control panels
that support a serial printer. The compatibility lists in
Table 1 show support information.
3
2
P1
DB9 GND
ENA BLE
P3
1
1- DB9 GND enable pins (P1)
2- RJ-16 data bus connector (P3)
3- Data bus (TS1)
4- Address DIP switches (S1)
5- Diagnostic LEDs
2.0 Specifications
Table 1: DX4010i Specifications
6- Diagnostic LED enable pins (P2)
7- DB9 DTE RS-232 connector (P6)
Operating
Voltage
12 VDC
Current Draw
50 mA nominal, 55 mA with diagnostic
LEDs enabled
3.0 Installation Standards
Failure to follow the instructions in this
manual can result in personal injury or
damage to the equipment.
Communication Programmable through the control
panel. Refer to the appropriate control
panel programming instructions.
Configuration
The baud rate for the printer output on a
DS7400Xi must be greater than 300 baud.
The DX4010i contains static-sensitive
components and must be handled with
care. Follow anti-static procedures when
handling the modules.
Operating
0°C to +50°C (+32°F to +122°F)
Temperature
Relative
Humidity
Control Panel
Compatibility
5 to 85% @ +30°C (+86°F)
non-condensing
Test according to NFPA 72 if used in fire
applications.
Option bus control panels: D6412,
D4412, DS7240, DS7220, DS7400Xi
(v2.02 or higher)
SDI bus control panels (v6.0 or higher):
D9412G, D7412G, D7212G, D9124,
D9112, D7412, and D7212
1. Disconnect power to the control panel by
unplugging the transformer and removing the red
battery lead.
2. Remove screws from enclosure cover to access the
DX4010i board.
Application
Compatibility
RPS: supported on all compatible
control panels
3. Connect circuit wiring and install jumper pins.
Refer to Section 4.0 Wiring on page 5.
4. Replace enclosure cover.
5. Connect a serial cable to the serial device. Refer to
Section 7.0 DB9 DTE RS-232 Connector (P6) on
page 10.
PC 9000: supported on SDI Bus
control panels (D9412G, D7412G,
D7212G, D9112, D7412, and D7212)
BIS: supported on SDI Bus control
panels, v6.3 and higher (D9412G,
D7412G, and D7212G)
CMS 7000: supported on DS7400Xi
Control Panels set at Mode 18 (v3.09
or higher)
6. Reapply power to the control panel.
Printers: supported on compatible
Option Bus control panel
4
Bosch Security Systems, Inc. | 1/05 | 4998141106C
Download from Www.Somanuals.com. All Manuals Search And Download.
DX4010i | Installation Instructions | 4.0 Wiring
4.0 Wiring
Figure 3: External Power Supply Connections
Remove all power to the control panel (AC
1
2
and standby battery) before making or
breaking any connections. Failure to do so
can result in personal injury or damage to
the equipment.
3
4
Wire Length Restrictions
5
6
•
•
0.8 mm (#22 AWG): 305 m (1000 ft)
1.2 mm (#18 AWG): 610 m (2000 ft)
SDI wiring is limited to 305 m (1000 ft).
+
-
7
Connect the DX4010i to the control panel data and
auxiliary power sources as shown in Figure 2.
1- DX4010i data bus
2- Control panel data bus
Figure 2: Control Panel Connections
3- Option AUX common/SDI common (black)
4- Option data/SDI B (green)
2
1
5- Option data/SDI A (yellow)
6- Option AUX power +/SDI power (red)
7- External 12 VDC power supply
3
4
5
6
B
G
Y
R
Figure 4 shows serial device-to-DX4010i connections
using the DB9 DTE RS-232 connector (P6).
Figure 4: Serial Device Connections
LED
1- DX4010i data bus
2- Control panel data bus
ENABLE
Rx Tx Tx Rx
BUS
SER
P2
P6
3- Option AUX common/SDI common (black)
4- Option data/SDI B (green)
5- Option data/SDI A (yellow)
6- Option AUX power +/SDI power (red)
P1
DB9 GND
ENABLE
If an external 12 VDC power supply is used, wire as
P3
shown in Figure 3.
1
1- Serial (RS-232) device such as a PC (with
RPS, BIS, PC9000, or other third party
application) or a serial printer for supported
control panels.
See Section 7.0 DB9 DTE RS-232
Connector (P6) on page 10 for additional
information.
Figure 5 shows a parallel printer connected to the serial
output of the DX4010i. This type of connection
requires the use of a serial to parallel converter, such as
the BlackBox PI045A serial to Centronics parallel
converter cable. The cable is available from
BlackBox® (www.blackbox.com).
Bosch Security Systems, Inc. | 1/05 | 4998141106C
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DX4010i | Installation Instructions | 5.0 DX4010i Jumper Pin Settings
Figure 5: Parallel Device Connections
Figure 6: P2 Jumper Settings
LED
ENABLE
1
Rx Tx Tx Rx
BUS
SER
P2
P6
LED
ENA BLE
R xTx
B US
TxR x
SE R
P2
P6
P1
DB9 GND
ENABLE
P3
P1
2
DB 9G ND
ENAB LE
P3
2
1
4
3
1- Parallel converter cable box (BlackBox P/N:
PI045A
2- Parallel printer (compatible option bus control
panels only)
1- Diagnostic LED enable pins (P2)
2- DB9 GND enable pins (P1)
3- Enabled
4- Disabled
5.0 DX4010i Jumper Pin
Settings
Table 2: Diagnostic LED Functions
5.1
Enable LED Jumper Pins (P2)
Use the diagnostic LEDs for troubleshooting. To
enable the LEDs, place a jumper plug across the
jumper pins labeled P2.
Diagnostic LED
BUS RX
Function
Data bus receives data from control
panel
BUS TX
SER RX
SER TX
Data bus transmits data to control panel
RS-232 receives data from serial device
RS-232 transmits data to serial device
Refer to Figure 6 for jumper pin settings.
The DX4010i draws more current when the
diagnostic LEDs are enabled. Do not
enable the diagnostic LEDs under normal
operating conditions.
5.2
DB9 Ground Enable Pins (P1)
Some devices connected to the DB9 DTE RS-232
connector (P6) can cause a ground fault condition on
the control panel. If this occurs, removing the plug
across the P1 jumper pins can clear the ground fault
condition.
Some devices might still cause a ground
fault even if the P1 jumper plug is removed.
Refer to Figure 6 for jumper pin settings.
6
Bosch Security Systems, Inc. | 1/05 | 4998141106C
Download from Www.Somanuals.com. All Manuals Search And Download.
DX4010i | Installation Instructions | 6.0 Remote Programming Direct Connection
5.3
Address DIP Switches
6.0 Remote Programming
Direct Connection
The address DIP switches are used to assign an address
to the DX4010i.
Refer to Table 3 for DIP switch option bus address
settings.
The DX4010i can be used to create a local direct
connection for remote programming of a compatible
control panel.
Refer to Table 4 for DIP switch SDI bus address
settings.
Option Bus: Set the address DIP switches to
Address 0. Refer to Table 3 on page 8.
Refer to Figure 7 for proper DIP switch orientation.
SDI Bus: Set the address DIP switches to Address 88.
Refer to Table 4 on page 9.
Figure 7: DIP Switch Location and Orientation
LED
ENAB LE
RxTx
BUS
Tx Rx
SER
Consult your control panel’s installation guide for
specific wiring connections.
P2
1
P6
A DB9 to DB9 null-modem cable is
required when using the direct connection
method.
P
1
DB9
G
ND
NABLE
E
P3
ON
2
3
1
2
3
4
5
6
7
8
1
2
4
8
16
32 64 128
4
1- Address DIP switches
2- ON position
3- OFF position
4- Address example (option bus Address 0)
Bosch Security Systems, Inc. | 1/05 | 4998141106C
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DX4010i | Installation Instructions | 6.0 Remote Programming Direct Connection
Table 3: Option Bus Address DIP Switch Settings
DIP Switch Settings
DIP
Switches
S1
S2
S3
S4
S5
S6
32
S7
64
S8
Module
1
2
4
8
16
128
Address
(Mode) (Option/SDI) (Checksum +1)
0*
1
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
2
OFF
OFF
ON
ON
ON
3
OFF
ON
ON
ON
4
OFF
OFF
OFF
OFF
ON
ON
5
OFF
ON
ON
ON
6
OFF
OFF
ON
ON
7
OFF
ON
ON
8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
9
OFF
ON
ON
ON
10
OFF
OFF
ON
ON
11
OFF
ON
ON
12
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
13**
14**
15
OFF
ON
ON
OFF
OFF
ON
OFF
ON
134
135
136
137
138
139
140
141
142
143
144
145
250
251
252
253
OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
* Installer’s mode: Use for direct connection of remote programming and diagnostic tools.
** DS7412 emulation
The DS7400Xi (USA) only supports one DX4010i
Option bus control panels: D6412, D4412, DS7240, DS7220, DS7400Xi (v2.02 or higher).
8
Bosch Security Systems, Inc. | 1/05 | 4998141106C
Download from Www.Somanuals.com. All Manuals Search And Download.
DX4010i | Installation Instructions | 6.0 Remote Programming Direct Connection
Table 4: SDI Bus Address DIP Switch Settings
SDI DIP Switch Settings
SDI DIP
Switches
S1
1
S2
2
S3
4
S4
S5
S6
32
S7
64
S8
Module
8
16
128
Address
(Mode) (Option/SDI) (Checksum +1)
80*
81
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
82
OFF
OFF
ON
ON
ON
83
OFF
ON
ON
ON
84
OFF
OFF
OFF
OFF
ON
ON
85
OFF
ON
ON
ON
86
OFF
OFF
ON
ON
87
OFF
ON
ON
88**
89
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
8A
8B
8C
8D
8E
8F
OFF
OFF
ON
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
Positions 5, 6, and 8 are not used for SDI bus.
* Used for BIS, PC 9000, and other third party applications.
** Used for RPS and alternate communication.
SDI bus control panels (v6.0 or higher): D9412G, D7412G, D7212G, D9124, D9112, D7412, and
D7212.
Bosch Security Systems, Inc. | 1/05 | 4998141106C
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DX4010i | Installation Instructions | 7.0 DB9 DTE RS-232 Connector (P6)
7.0 DB9 DTE RS-232
Figure 8: DB9 Connector Layout
Connector (P6)
The DX4010i serial port is wired as a DTE device.
1
2
3
4
5
•
If the connected device is a data carrier
equipment (DCE) device (most common, such
as an external modem), a straight through 9-pin
to 9-pin, or (DTE to DCE) 9-pin to 25-pin cable
may be used.
6
7
8
9
•
If the connected device is a DTE device (such as
a PC serial port), a null-modem (DTE to DTE)
9-pin to 9-pin, or null-modem 9-pin to 25-pin
cable is required.
1- DCD
2- RxD
3- TxD
4- DTR
5- GND
6- DSR
7- RTS
8- CTS
9- RI
Consult the operating manual provided with your
compatible device for wiring requirements.
If you are using an alternate configuration, you must
make a custom cable (refer to Figure 8 and Table 5).
Table 5: Alternate Wiring Configuration
DX4010i
9-Pin DTE
Connector
DCE
(9-pin)
DTE
(9-pin)
DCE
(25-pin)
DTE
(25-pin)
1: DCD
1: DCD
1: DCD 8: DCD
8: DCD
(not used)
2: RxD
3: TxD
4: DTR
5: GND
6: DSR
7: RTS
8: CTS
9: RI
2: RxD
3: TxD
4: DTR
3: TxD
2: RxD
3: RxD
2: TxD
2: TxD
3: RxD
6: DSR 20: DTR 6: DSR
5: GND 5: GND 7: GND 7: GND
6: DSR
7: RTS
8: CTS
9: RI
4: DTR
8: CTS
7: RTS
9: RI
6: DSR
4: RTS
5: CTS
22: RI
20: DTR
5: CTS
4: RTS
22: RI
(not used)
10
Bosch Security Systems, Inc. | 1/05 | 4998141106C
Download from Www.Somanuals.com. All Manuals Search And Download.
DX4010i | Installation Instructions | 8.0 RJ-16 Data Bus Connector (P3)
8.0 RJ-16 Data Bus Connector
(P3)
Figure 9: P3 Connector
LED
ENABLE
RxTx Tx Rx
BUS SER
P2
P6
P1
DB9 GND
ENABLE
1
P3
1- RJ-16 data bus connector (P3)
For remote programming connection, use one of the
two cables supplied: RJ-16 to molex for control
panels with the data bus provided on a header (such
as the D6412 or DS7240) or the RJ-16 to spade lugs
for terminal strip connections (such as the D9412).
Bosch Security Systems, Inc. | 1/05 | 4998141106C
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Bosch Security Systems
130 Perinton Parkway
Fairport, NY 14450-9199
Customer Service: (800) 289-0096
Technical Support: (888) 886-6189
© 2005 Bosch Security Systems
4998141106C
Download from Www.Somanuals.com. All Manuals Search And Download.
|