DISHWASHER
Installation
Instructions
LAVE-VAISSELLE
Instructions
LAVADORA DE PLATOS
Instrucciones
d’installation
de instalación
Cycle Countdown
Power
Scrub
Plus
Scrub
Wash
Regular
Wash
Delicate/
Econo
Quick
Wash
Rinse
Hold
Refill
Rinse
Agent
On/Off
&
On /Off
High
Temp
Wash
Regular Rinse
Temp
Wash
&
Hold
Power Scrub
Rinse
Hold
Regular
Wash
&
Top
Rack
Only
Delay
Start
Hours
Power
Temp.Options
Power
Cancel
Drain
Cycles
SHI66A,
SHU33A, SHU43C, SHU53A, SHU66C,
SHU43E, SHU53E, SHU66E,
SHV46C, SHV66A,
SHX33A, SHX46A, SHX46B, SHX56B,
SHY56A, SHY66C
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
THESE INSTALLATION INSTRUCTIONS ARE INTENDED
FOR USE BY QUALIFIED INSTALLERS.
In addition to these instructions the dishwasher shall be installed:
• In the United States, in accordance with the National Electric
Code/State and Municipal codes and/or local codes.
• In Canada, in accordance with the Canadian Electric Code
C22.1 -latest edition/Provincial and Municipal codes and/or
local codes.
Please read these installation instructions completely and carefully.
They will save you time and effort and help to ensure optimum dishwasher
performance.
Be sure to observe all listed
warnings and cautions. (Look for
WARNING
the triangles with exclamation marks
inside.)
CAUTION
IMPORTANT
•
•
NEW INSTALLATION - If the dishwasher is a new installation, most of the work
must be done before the dishwasher is moved into place.
REPLACEMENT - If the dishwasher is replacing another dishwasher, the
connections for the dishwasher being replaced must be checked for
compatibility with the new dishwasher and replaced as necessary.
INSPECT THE DISHWASHER
After unpacking the dishwasher and prior to installation, thoroughly inspect the
dishwasher for possible freight or cosmetic damage. Report any damage immediately.
Cosmetic defects must be reported within 5 days of installation.
NOTE: Please do not discard any bags or items that come with the
original package until after the entire installation has been completed!
2 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS & MATERIALS NEEDED
Tools Needed for Installation
Hammer
Hole saw or 1” hole cutter
Pipe wrench, 2 reqd.
Tape Measure
Wire Cutter
Slotted screwdriver (#2)
Phillips screwdriver (#2)
Adjustable wrench,
(size med., 2 reqd.)
Torx screwdriver, #20
Level
Wire stripper
Electric Drill
Figure 1
Materials Needed
Electric Connection - 2 conductor, 1 ground
insulated electrical supply cable (30” or
sufficient length for your installation).
1
2
Hot Water Supply Line - Minimum 3/8”
O.D. copper tubing or metal braided
dishwasher supply line.
Shut-off valve and fittings for hot water
supply line.
3
4
90° elbow with 3/8” N.P.T. external threads
on one end and sized to fit your water
supply line on the other end.
Teflon tape or other pipe thread compound
which help seal plumbing connections.
T
APE
5
6
7
3 twist-on wire connectors for 16 AWG
wire.
UL listed conduit connector or strain relief.
Additional materials may be required to comply with local codes.
Figure 2
ENGLISH - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
MATERIALS SUPPLIED
Accessory Parts Supplied
Accessory Parts for your model dishwasher will
come in one or more plastic bags. Check to
make sure that the parts supplied for your
model are all there. See Figure 3. If any parts
are missing contact your dealer immediately.
A
B
C
D
E
DISHWASHER
INSTALLATION KIT (Clear Bag)
D. Toe Panel Screws (8mm) (2)
E.
F.
Mounting Brackets (1L & 1R)
Mounting Bracket Screws (2)
F
G
H
G. Rubber Connection Hose (1)
and Drain Hose Clamps (2)
SHY66 & SHX56 Models
• Dishwasher Installation Kit (1) and
• (Green Bag) w/ the following:
L.
J-Box Cover (1)
M. J-Box Screw (8mm) (1)
N. Toe Panel Screw (4x16) (2)
I
J
SHV and SHI Models
• Dishwasher Installation Kit and
• Outer Door Installation Kit (Blue bag):
K
L
J.
C.
K.
I.
SHI/SHV Panel Installation Template
Cap (2 Blk)
Wood Screws (2)
Mounting Door Brackets(2 plastic)
w/Screws (4) and;
M
N
O
Mounting Door Brackets (2 metal)
w/Screws (4)
H. Spring Tension Screw (2)
Manual Bag
All Dishwashers come with a manual bag.
The following contents are located in every
bag:
P
• Use & Care Manual
• Installation Instructions
P. Tall Item Sprinkler (1)
Q
R
SHY66 & SHX56 models
have an additional part:
Q. Cotton Insulation Strip (1)
Figure 3
Note: Pictures are not to scale.
4 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING A LOCATION
THESE INSTALLATION
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
Choosing the Location
Select a location as close to the sink as
possible for ready access to water and drain
lines.
Most of the installation work is done before
the dishwasher is moved into place.
1-15/16” (49mm)
4” (102mm)
Figure 4
Any built-in dishwasher must be fully
enclosed on the top, both sides and back.
Therefore the cabinet space below your
counter is probably the best location.
23-9/16” (598 mm)
90°
90°
For proper operation and appearance of the
dishwasher, the cabinet opening should be
square and have dimensions as shown in
Figure 5.
23-5/8” - 24-1/8” (600-613 mm)
Figure 5
Clearance
for door
opening
Dishwasher
Countertop
If the dishwasher is to be installed in a
corner, make sure there is adequate clea-
rance to open the door. See Figure 6.
Door in
open
position
Figure 6
ENGLISH - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
PLUMBING PREPARATION
THESE INSTALLATION
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
CAUTION
To protect against possible rupture of
the fill valve, water lines leading to
the dishwasher, as well as water lines
in the dishwasher MUST be protected
against freezing. If the valve or water
line freezes, flooding may occur. Such
ruptures are not covered by the
warranty.
Drain Hose
The dishwasher comes with a seven (7)
foot drain hose.
• A 1.25” access hole must be made to
allow the drain hose to be run to the
drain connection location.
IMPORTANT
If no air gap is used and the drain
line is run into a sink or disposer,
the drain line must be elevated to
a point higher than the highest
water level of the sink to prevent
Hot Water Supply
•
•
The hot water line to the dishwasher
must provide between 5 - 120 psi (0.3-
8.27 bars) water pressure.
The hot water heater should be set to
deliver 140°F (60°C) water
back
siphoning
into
the
dishwasher.
temperature to the dishwasher.¹
A 3/8” minimum O.D. copper tubing
inlet line is recommended.
All solder connections must be made
before water line is connected to the
dishwasher’s inlet water valve. Do not
solder within 6 inches (152.4 mm)
of the dishwasher’s inlet water
valve.
•
•
NOTE: If connection to an air gap is
required by local code, air gap kits are
available from local plumbing sources.
Install the air gap according to the
manufacturer’s instructions.
•
Drill a 1” (25.4 mm) diameter access
hole in the cabinet for the water supply
line (Figure 9A).
•
Run the line to the approximate fill
valve location, as shown in Figure 9A.
Drain
Hose
It is recommended that a shut-off valve (not
supplied) be installed in the hot water
supply line in a readily accessible location,
see Figure 9.
Hot water
line
Electrical supply cable
Figure 7
1. In order to reduce running time, Bosch recommends 140° F water inlet
temperature. Your dishwasher will perform equally as well at 120° F water
temperature, but the run time will be extended.
6 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL PREPARATION
WARNING
THESE INSTALLATION
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
23-5/8”-24-1/8”
(600-613mm)
3-1/2
(90 mm)
1-5/16
Electrical Supply
The customer has the responsibility to
ensure that the dishwasher installation is
in compliance with all national and local
electrical codes and ordinances. The
dishwasher shall be installed by a qualified
electrician and properly grounded. The
electrical supply for which the dishwasher
is designed is 120V, 60 Hz, AC, connected
to a dishwasher-dedicated electrical circuit
with a fuse or breaker rated for 15 amps.
If the dishwasher is connected with a food
disposer, a 20 amp (and no higher) fuse or
circuitbreaker may be used. No other
appliances or outlets should be connected
to the dishwasher supply circuit. Electrical
supply conductors shall be copper only and
shall be minimum #16 AWG. Wire
connectors proper for the size and number
of wires used to connect the dishwasher
to the supply circuit shall be used. Do not
use all-plastic wire connectors. Strip power
supply wires approximately ½ inch. Do not
pre-twist wire before applying wire
connector. After installing wire connectors,
gently tug wires to check the integrity of
the connector. Place all wires and
connectors into the power supply box,
and reinstall cover with the screw provided
(49 mm)
Figure 8
Electrical Rating
Volts Hertz Amperes
Watts
1,450
(max)
120
60
15
Table 1
Openings for electrical lines must be
installed in the marked areas as
shown in Figures 8 and 9 to avoid
interference with the dishwasher
frame or other components.
in the installation package.
• Cut a 1” (25.4mm) diameter hole in the
Shut-off
valve
cabinet (in area of Figure 9 B). For wood
cabinets, sand the hole until smooth.
For metal cabinets, cover the edge with
a grommet.
A
B
14”
(355 mm)
HWS
21”
(533 mm)
• Run flexible cable (as codes permit) from
junction through hole in cabinet. Cable
should extend 30” (762 mm) from back
wall.
Hot water supply line Electric supply cable
Figure 9
ENGLISH - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
PLACING THE DISHWASHER
A. Mounting bracket
for mounting to under
countertop
Placing the Dishwasher
The profile strips on the sides of the
dishwasher allow the dishwasher to fit into
a cabinet opening with a width of 23-5/8”
(600 mm) to 24-1/8” (613 mm). Before
sliding the dishwasher into the cabinet
opening:
A
B
• Straighten the hot water supply line and
the electrical cable (see Figure 11).
• Level & Align (initial adjustments).
• Guide the drain hose carefully (avoiding
kinks in hose) as the dishwasher is slid
into the cabinet opening.
• Make final leveling adjustments (see
FINAL STEPS Section).
• To maintain the dishwasher position and
alignment, first determine which type
of mounting your dishwasher needs:
B. Mounting bracket
bent for mounting to
side of cabinets
Figure 10
Top Mount is used for all types of
countertops that will not be damaged
by drilling.
IMPORTANT
If you wish to change the front panel of
the dishwasher this must be done before
sliding the dishwasher into place.
•
For a top mount, position the
brackets flat on each of the top
corners of the dishwasher as
shown in Figure 10A.
*Note: Additional accessory door pa-
nels can not be used with SHU 9900
models.
Side Mount is used when there is a
granite, marble or other hard natural
surface counter top that could be
damaged by drilling.
•
For a side mount, bend the
brackets, then position them as
shown in Figure 10B.
• Drive Mounting Screws (see Figure 3)
through the holes in the brackets. See
Figure 10A or 10B.
• Connect the drain hose, hot water
supply line and electrical connections
as described in the following sections.
Figure 11
8 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
DRAIN HOSE CONNECTION
Air Gap
THESE INSTALLATION
Drain Hose
in Sink with
Air Gap/ No
Disposer
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
Rubber
Connector
Be sure to follow your national
and local codes at all times.
Trap
Drain Hose
• Before beginning, turn off the water
supply!
Figure 12
• The access hole for the drain hose should
be 1.25” (32 mm) diameter.
• Use the hose clamps and rubber
connection hose (Figure 3) to connect
the drain hose to the sink, disposer or
air gap (Figure 14).
Air Gap
Drain Hose
in Sink
with Air
Gap &
Rubber
Connector
Disposer
Openings for drain lines must be
installed in the marked areas as
shown in Figures 8 and 9 to avoid
interference with the dishwasher
frame or other components.
disposer
Trap
Figure 13
G, Fig 3
Drain Hose
Connected
to Sink
CAUTION
Failure to provide the proper drain
connection height, 20” (508mm)
above floor level with high loop or
air gap, will result in improper
draining of the dishwasher.
Improper draining may cause
damage to the dishwasher.
Figure 14
ENGLISH - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOT WATER CONNECTION
THESE INSTALLATION
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
Shut off valve
(not included)
Connecting the Hot Water
Supply Line
• If using a solder joint instead of a com-
pression fitting, be sure to make all
solder connections before connecting
the water line to the dishwasher.
• Make sure there are no sharp bends or
kinks in the water line which might
restrict water flow.
Figure 15
• When connecting threaded pipe use pipe
thread compound or Teflon tape to seal
the connection.
• Before connecting the copper hot water
supply line to the dishwasher, it should
be flushed with hot water to clear any
foreign material.
• Apply Teflon tape or other pipe sealant
to 90° elbow fitting and connect
directly to water inlet valve*.
CAUTION
DO NOT SOLDER WITHIN 6 INCHES
(152.4 MM) OF THE DISHWASHER’S
INLET VALVE.
TEMPERATURES REQUIRED FOR
SOLDERING WILL DAMAGE THE
VALVE!
• Turn on the water supply to check for
leaks after making connections.
* Water inlet valve located at the bottom
left front of the dishwasher.
Openings for water lines must be
installed in the marked areas as shown
in Figures 8 and 9 to avoid
interference with the dishwasher
frame or other components.
Figure 16
10 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SUPPLY CONNECTION
THESE INSTALLATION
INSTRUCTIONS ARE
WARNING
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
ELECTRICALSHOCKHAZARD
• DISCONNECT ELECTRICAL POWER
AT THE CIRCUIT BREAKER BOX OR
FUSE BOX BEFORE INSTALLING THE
DISHWASHER.
Connecting Electrical Supply
• ELECTRICALLY GROUND DISH-
WASHER.
• USE COPPER CONDUCTORS ONLY.
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
Be sure to follow all local and natio-
nal electrical codes and ordinances.
• Install strain relief or conduit connector
into opening on power supply box.
• Strip the insulated wires, being extremely
careful not to strip too much insulation.
• Insert and securely fasten into strain re-
lief, two-conductor supply cable with
ground.
Correct Connection in Junction Box
• Twist wire connectors tightly onto the
wires, ensuring that no bare wiring is
exposed (from insulated wires).
• Press wires back into J-box
• Securely fasten the J-box cover or toe
panel (depending on model) with
screw(s) provided from accessories
package.
Black to Black
White to White
Green or Bare
to Green or Bare
U.L. listed
Conduit
Connector
or Strain
Relief
* Junction box located at the bottom
right front of the dishwasher base.
Figure 17
Grounding Instructions
This appliance must be connected to a
grounded metal permanent wiring system;
or an equipment grounding conductor
must be run with the circuit conductors
and connected to the equipment grounding
terminal or lead on the dishwasher. The
dishwasher must be properly grounded
before operating. Make sure that the
dishwasher is connected to a suitable
ground in compliance with the NATIONAL
ELECTRICAL CODE, in the United States,
or the CANADIAN ELECTRIC CODE C22.1-
latest edition, in Canada as well as any pro-
vincial/state or municipal or local codes that
apply.
Incorrect Connection in Junction Box
Figure 18
ENGLISH - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
DOOR PANEL INSTALLATION
Accessory Panel Installation SHU Models
If you have an SHU model and have ordered an accessory panel kit it must be installed
prior to sliding the dishwasher into place. Dimensions of panel size that may be used is
shown in Figure 19.
Panel Installation, SHV Models
If you have an SHV model, a fully integrated model, you will have additional mounting
hardware and a folded template sheet with installation instructions comprised of
pictograms.
Refer to the folded template sheet for information on how to mount the panel. Please
note that one side of the template shows how to mount a one piece panel and the other
side of the template shows how to mount a two piece panel. Be sure of what type
installation you want before proceeding with the installation.
Refer to Figure 20 and Table 3 for guidelines on custom door panel selections.
After deciding if the extension pieces will be used or not refer to the pictograms printed
on the template for proper method of mounting your custom door.
Panel Installation, SHI Models
If you have an SHI model, an integrated model, you will have additional mounting
hardware and a folded template sheet with installation instructions comprised of
pictograms. In North America the stainless steel models of the integrated series (SHI
series), have a control panel that is 5-5/16” (135 mm) tall. The stainless steel model
comes with two extension pieces, referred to as the standard and long extension piece
in Table 2: the standard piece is used for drawer heights up to 6” (152mm); the long
extension piece is used for drawer heights greater than 6” (152mm) but 6-7/16” (164mm)
or less. These stainless steel extension pieces are not installed in the control panel. In
the stainless steel models, the two extension pieces are shipped loose and must be
inserted as shown in pictogram 5 on the template sheet.
The purpose of the extension piece is to allow the increase of the control panel height to
try to match the horizontal drawer line of the cabinets. If your drawers are taller than the
“C” dimension shown on Table 2, it is recommended that the extension either be slid in
as far as it will go, or removed and the door made to fit directly below the control panel.
12 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
DOOR PANEL INSTALLATION
1/4” max.
(6 mm)
25”
(636 mm)
SEEFOLDEDPANELINSTALLATION
TEMPLATE SHEET FOR STEP BY STEP
INSTRUCTIONSONHOWTOINSTALL
YOUR DISHWASHER PANEL(S).
23-1/16”
(586 mm)
Figure 19
IMPORTANT
Do NOT Drill Completely through
your custom door panel.
EXTENSION "A"
MAX.-MIN.
"C"
MAX.-MIN.
MODEL
"B"
STANDARD
LONG
11/16 - 5/16"
(18-8mm)
1 1/8 - 11/16" 5 5/16 (135 6 7/16 - 5 5/8
(29 - 18mm) mm) (164 - 143 mm)
SHI66C05UC
Table 2
Figure 20
MODEL
SHV
D
E*
F
27 3/16" - 30 5/16"
(690 - 770 mm)
N/A
20 11/16 - 25
(526-635 mm)
27 3/16" - 30 5/16"
(690 - 770 mm)
23 3/16 - 23 3/8
(589 - 594 mm)
SHI
Table 3
Figure 21
*Note: Do not exceed 30 5/16” (770mm)
for the overall front panel length.
ENGLISH - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
FINAL ADJUSTMENTS
Door Tension Adjustment
(only in SHI and SHV models)
After installation of the dishwasher, open
and close the door several times to make
sure that it does so with ease. If the door
closes too quickly or if the door falls open,
the spring tension needs to be adjusted.
Adjust screws
on right and
left sides
To Adjust the Spring Tension
• Obtain Spring Tension Screws (2) out
of the SHI/SHV parts bag (see Figure
3).
Torx T 20
Figure 22
• Insert the screws in the right and left
sides and adjust spring tension as shown
(see Figure 22).
Leveling the Dishwasher
Raising the Rear
The rear leveling leg is adjusted by turning
the center screw at the front of the
dishwasher.
Torx T 20
Raising the Front
The front leveling legs are adjusted by
rotating the leveling legs on the front left
and right sides of the dishwasher.
Figure 23
• Use a screwdriver and tap the end lightly
with a hammer to turn the legs (see
Figure 23).
Note: If additional height is needed:
Shims may be added under the leveler feet.
14 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE AND TOE PANEL
SHY66 & SHX56 Series Base and Toe Panel Installation
Steps
SHU6800BASEPARTS
SHY66 & SHX56 BASE PARTS
Installation Parts
SHY66 & SHX56 Base Part
Base Part Screws
SHY66 & SHX56 Toe Panel
SHU Toe Panel Screws
•
•
•
•
•
Base Part
Base Part
Screws (1lft &1rgt)
(attached)
SHY66 & SHX56 Installation Kit
(Refer to “Materials Supplied” section)
Toe Panel
Junction Box Cover and Screw
Remember to carefully check, the “Materials
Supplied” section against the Installation Kit
bag and contents.
Figure 24
Disassembly Steps
Pull Toe Panel off (Figure 25).
Loosen Screws
•
•
LOW TORQUE, USE HAND TOOL
ONLY.
•
Remove Base Part by pulling it out
and downward.
Figure 25
After installation, water and electrical
lines are connected and the unit leveled,
assemble the base part (see below).
Assembly Steps
•
Place J-Box Cover on J-Box, insert
and tighten screw (Figure 26).
Drop screws inside holes in base part.
Slip Base Part under and up front
bottom panel of dishwasher. Tighten
Base Part Screws - LOW TORQUE,
USE HAND TOOL ONLY.
•
•
•
Slip Cotton Insulation Strip under
unit, between the bottom of Base
Part and the floor.
Figure 26
Junction Box Cover is required
for any installation application
ENGLISH - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
TOE PANEL AND HANDLE
Regular Toe Panel
Installation (for models
other than SHY66 & SHX56)
• Obtain Toe Panel Screws from the
Dishwasher Installation Kit bag (see
Figure 3).
• Insert screws through the Toe Panel.
• With a Torx screwdriver, fasten screws
and toe panel into dishwasher base.
Figure 28
16 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
FINAL CHECKLIST
Final Checklist
Check Electrical Requirements.
Be sure you have correct electrical supply and recommended grounding method.
Turn on the hot water shut-off valve and electrical supply. Incoming water
temperature should be 120°F-140°F (49°C-60°C).
Operate the dishwasher through one cycle and check for plumbing leaks.
If the dishwasher does not operate properly, refer to the SELF- HELP, CUSTOMER
SERVICE and WARRANTY sections in the Use and Care Manual.
Customer Service Information
If service becomes necessary, contact your dealer or installer or an authorized service center. Do
not attempt to repair the appliance yourself. Any work performed by unauthorized personnel may
void the warranty. If problem persists, take the following steps (in the order listed below) until the
problem is corrected to your satisfaction.
1. Contact your installer or the Bosch Authorized Service Contractor in your area.
3. Write to us at the address below:
BSH Home Appliances, Corp.
5551 McFadden Avenue
Huntington Beach, CA 92649
4. Call us at: 1-800/944-2904.
Please be sure to include (if writing), or have available (if calling), the following information:
•
•
•
•
•
Model Number
Serial Number
Date of Original Purchase
Date Problem Originated
Explanation of Problem
Also, if writing, please be sure to include a daytime phone number.
(You will find the model number and serial number information on the label located on the right-hand
side of the inner door of the dishwasher).
LEAVEINSTALLATIONINSTRUCTIONSAND
USE & CARE MANUAL WITH OWNER.
ENGLISH - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
18 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
|