Bodyguard Treadmill T700 User Manual

BODYGUARD^®FITNESS, division of Procycle

CANADA

9095, 25^thAvenue, Saint-Georges

(Québec) Canada G6A 1A1

The name “Bodyguard Fitness^®” and heart logo are

registered trademarks of Procycle Group Inc.

T700

TREADMILL

O W N E R ’ S M A N U A L

R0 01/2006

591181

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY NOTICE

Important Safety Notice

Impotant Safety Notice

READ THIS MANUAL THOROUGHLY BEFORE ATTEMPTING

TO ASSEMBLE OR USE THIS EXERCISE EQUIPMENT.

To ensure that you get the maximum beneﬁt from the engineering that has gone into your machine, we recommend

that you read this manual carefully before attempting to assemble and use the T700. Save these instructions and refer to

this manual if you are unfamiliar with the operation of the T700.

WARNING – Before attempting to use any of this equipment you should read this instruction manual carefully. Use of

this equipment by people with heart or other medical problems may result in serious injury. You should consult with a

physician prior to using this equipment. It is recommended to periodically consult your physician as you continue to use this

equipment. Immediately cease exercise if you feel dizzy, faint or short of breath. Use of this equipment in a manner other

than as prescribed by the instructions herewith may result in serious injury.

AVERTISSEMENT – Une lecture attentive de ce manuel d’instructions est recommandée avant de commencer à utiliser cet

appareil. Son utilisation peut provoquer des blessures sérieuses chez les personnes souffrant de troubles cardiaques ou

autres problèmes médicaux. Il est recommandé à ces personnes de consulter leur médecin avant d’utiliser cet appareil. Il est

aussi recommandé de consulter régulièrement le médecin au cours de la période d’entraînement. Si vous êtes pris de

vertiges ou d’étourdissements, si vous vous sentez défaillir ou avez le soufﬂe court, cessez immédiatement l’exercice.

L’utilisation de cet appareil d’une manière inadéquate ou autre à celle décrite dans ce manuel d’instructions peut entraîner

des blessures sérieuses.

For Your Personal Safety

Do not place towels or clothing on any part of the treadmill.

Do not place liquids near the computer console, electrical power plug, ON/OFF switch or any part of the treadmill.

Before attempting to disconnect the power, exit the program screen, then turn power OFF. To reduce any risks of electrical

shock, do not pull the power cord from the cable. Gently remove the power cable by the head from the wall outlet.

Do not operate the treadmill if the power cord is damaged or if the treadmill is not working correctly. If the power cord

is damaged, please contact your distributor or manufacturer to get it replaced. The rating of the new power cord must be

20 amps (125 volts AC) or 15 amps (250 volts AC) depending on the model and it must be 3.5 meters long (or 11 feet)

minimum.

Keep the power cord away from all moving parts of the treadmill, such as the elevation arm assembly and front transport wheels.

Do not use an extension cord that is not properly grounded. Keep all extension cords clear of all moving parts of the treadmill.

Place the equipment in a way that the power can be easily interrupted by pulling the power cord.

Do not allow children near the treadmill when in operation. Do not allow children unsupervised near the treadmill and keep

the safety key in a safe place away from children.

Wear proper exercise footwear when using the treadmill. Do not use the treadmill in bare feet or in socks. It is normal for

the treadmill belt to discharge soil or rocks that are on the sole of your shoes. It is always good practice to clean the soles

of your shoes before using the treadmill.

Never use the treadmill with more than one person on the belt.

Never try to accelerate or decelerate the speed of the running belt by pushing on it or trying to stop it, with or without power.

Always face towards the computer display and do not run backwards on the belt.

The treadmill should not be boxed in with other furniture or obstacles. Keep the rear and side of the treadmill clear of any

obstructions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical Information

CAUTION – This equipment is intended to be electrically grounded. The three-wire grounding plug (polarized) will ﬁt

only a grounded AC outlet. Do not use an extension cord or outlet if it does not accept three-wire grounding plugs.

Contact a licensed electrician to replace the outlet with a properly grounded outlet.

WARNING – To prevent the risk of ﬁre or electrical shock, do not expose this machine to rain or moisture. Do not place

machine outdoors. Do not place machine near swimming pools, sauna rooms or high humidity environments. Refer

servicing to qualiﬁed Bodyguard^®Service personnel only.

MISE EN GARDE – Cet appareil est conçu pour une installation électrique avec ﬁl de terre. La ﬁche à trois ﬁls ne s’adaptera

qu’à une prise C.A. avec ﬁl de terre. L’appareil ne doit pas être branché à un ﬁl de rallonge ou une prise de courant qui

n’accepte pas les ﬁches à trois ﬁls. Faites appel à un électricien qualiﬁé pour le remplacement de la prise de courant par une

prise avec ﬁl de terre.

ATTENTION – Aﬁn de prévenir les risques d’incendie ou de chocs électriques, l’appareil ne doit pas être exposé à la pluie ou

à l’humidité. En conﬁer l’entretien à une personne qualiﬁée de Bodyguard^®uniquement.

If you have any questions about the assembly, proper use or repair of your treadmill, please call your local Bodyguard^®

Dealer. All necessary adjustments or repairs during the warranty period must be made by an Authorized Bodyguard^®

Dealer.

IMPORTANT NOTICE : This treadmill should be connected in a dedicated circuit in order to avoid functional problems.

NOTICE IMPORTANTE : Cet appareil est conçu pour être branché dans un circuit dédié pour éviter des problèmes

fonctionnels.

Should you need more information, you can call our Customer Service Department at:

1-418-228-8934 / 1 800 373-2639

Know Your Heart Rate

200

To determine your recommended heart rate level, select the type of exercise

program you wish to follow. Your MAXIMUM HEART RATE (MHR)

is calculated as follows:

180

MHR

220 – Age

160

140

120

100

It is not recommended to exercise above 90% of your MHR.

Exercise in 70-80% MHR area for an aerobic exercise.

Exercise in 60-70% MHR area for a moderate, healthy heart zone.

Exercise in 50-60% MHR area if you wish to train in a fat burning zone.

Difﬁcult to achieve exercise beneﬁt below 50% MHR.

Your Age

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty Information

BODYGUARD^®FITNESS

T700 Limited Warranty

Bodyguard^®Fitness warrants that product is in good working order and free of manufacturing defects in workmanship and

materials.

The T700 is guaranteed for a period of:

• Lifetime on main frame and motor

• 10 years on parts*

• 3 years on labor

In a residential (home) application only

In an institutional application only

In an commercial application only

The T700 is guaranteed for a period of:

• Lifetime on main frame

• 5 years on motor

• 3 years on parts*

• 1 year on labor

The T700 is warranted for a period of:

• Lifetime on main frame

• 3 years on motor

• 2 years on parts*

• 1 year on labor

This warranty is non-transferable and applies to the original owner of the unit only.

*Once the labor warranty has expired, shipping and handling cost of parts will be the end-user’s responsibility.

Responsibility of the User

The following items are not included in the Warranty since they are not considered manufacturing defects.

1. Damage resulting from any accidental use, disaster, misuse and abuse.

2. Service and parts required due to improper fusing or wiring.

3. Service and parts required as a result of improper servicing or from an unauthorized dealer.

4. Service and parts required as a result of ﬂood, ﬁre, vandalism or acts of God.

5. Labor to correct installation of the unit or instructing owners on how to use and install the unit.

6. Wear items such as handle bar foam coverings, drive belts and paint ﬁnish corrosion or discoloration resulting from

improper cleaning of the unit.

7. Do not put any lubricant product of any type (except the Bodyguard^®Fitness lubricant) on the running belt. Using a

lubricant not approved by Bodyguard^®will void the belt/deck warranty.

This Warranty is in addition to any statutory warranty. This Warranty supersedes all other written or expressed warranties.

In the event your T700 treadmill should require service, you must contact the Authorized Bodyguard^®Dealer where you

purchased your machine or the nearest Authorized Bodyguard^®Dealer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating your T700

Each T700 treadmill contains a L.E.D. (light emitting diode) computer display monitor. The control functions, unique

programs and features have been designed with you in mind, to offer the best possible exercise by displaying important and

clear information regarding your excercise progress.

Please familiarize yourself with the functions of the computer display monitor and each program to allow you to have the

best possible exercise.

The T700 comes with an emergency stop button. Press this button if you need to stop immediatly the running belt.

1.1 Getting to Know the T700

Computer Display Monitor

The computer display monitor consists of a main viewing screen, a central informational window and two additional

informational windows.

T700 COMPUTER DISPLAY MONITOR

Horizontal rectangles (dot) represent speed and elevation values.

Each tick represents either 1 mph (1.6 km/h) or 1.5% elevation change.

The minimum values start from 0,5 mph (0,8 km/h) and -3% elevation at the bottom,

and the maximum values end at 15 mph (24.0 km/h) and 15% elevation to the top of the scale.

Numeric Keypad

Treadmill Series

Enter key

QUICK SPEED

ENTER

MANUAL

CARDIO

WARNING: Stop if you feel dizzy or faint at any time during your exercice.

Central information window

Speed proﬁle (bright green)

Elevation proﬁle (light green)

SELECT

ELAPSED TIME

TARGET REMAINING

PACE

INTERVAL

RANDOM

SPEED

DISTANCE

ELEVATION

CALORIES

WEIGHT

LOSS

Flashing dot under proﬁles indicates

your progress in a program.

The program starts from the left

and ends at the extreme right side

CAL

HOUR

HEART RATE

H.R.

CONTROL

Pause

PAUSE

COOL DOWN

OTHER

PROGRAMS

Other programs key

ﬁgure 6

Cool Down

Clear/Stop key

Each exercise program starts from the left part of the screen and terminates when it reaches the right part of the screen.

A ﬂashing dot will indicate your progression in the program.

As the speed and elevation increase, the corresponding proﬁle will move towards the top of the viewing screen. At the top

of the screen, a scrolling message center displays all your exercise parameters from the start of the program.

The three informational windows will display SPEED, DISTANCE, ELEVATION, CALORIES, CAL/HOUR, HEART RATE, ELAPSED

TIME, TARGET REMAINING and PACE.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPEED indicates the treadmill belt speed in miles per hour or kilometer per hour, ranging from 0.10 to 15.00 mph or

0.1 to 24.00 km/h.

DISTANCE displays the total distance in miles or kilometers from the start of the exercise, ranging from 0.00 to 99.00

miles or 0.00 to 99.00 km.

ELEVATION will display the slope of the running belt in terms of percentage varying from -3% to 15%. As an example,

one percent (1%) slope is equal to one foot (or one meter) climbed for each 100 feet (or 100 meters) covered.

CALORIES will indicate total of your caloric expanditure from the start of the exercise.

CAL/HOUR will indicate the hourly caloric expenditure based on your weight input and actual exercise intensity level.

HEART RATE will display your actual heart rate if the optional heart rate chest strap is used. The display will be shown

in beats per minute.

ELAPSED TIME indicates the amount of time accumulated from the start of any program. The time will range from 0

to a maximum of 99 minutes.

TARGET REMAINING indicates the duration (time, distance or calories depending on your settings) left once a program

has started.

PACE indicates how long it will take to complete one mile or one kilometer at that current speed. Pace per mile or

kilometer is shown in minutes and seconds.

NOTE – The parameter like calories displays an evaluation of the real values of your exercise parameters. The evaluations

are based on formal information, tests and are supported by specialists and physicians.

Keys

During an exercise, you can change the value shown on each informational window by pressing the adjacent round select

key once. If you wish to have the information displayed in a scanning mode, simply hold down the round select key for three

seconds and release it. You can also activate any window to scan by repeating the above sequence. To remove the scan, just

press the round select key once again.

The INCREASE and DECREASE Speed keys allow you to modify the speed of the running belt during an exercise. These

keys also allow you to select the programs and parameters prior to each exercise. During any exercise program, you can

modify the speed of the belt by pressing or holding either the INCREASE or DECREASE Speed key. If you continuously

hold down a Speed key, the speed display will change by a tenth of a mile (or kilometer) per hour (0.1 mph or 0.1 km/h).

Release the Speed key when you have selected your desired exercise speed.

Notice that the treadmill belt will slowly change to your desired speed. The desired SPEED L.E.D. will be

displayed ﬂashing on the display window on the left, while the actual belt speed slowly ramps up to your

target speed. Once the speed has been attained the SPEED L.E.D. will stop ﬂashing.

The CLEAR/STOP key allows you to cancel a program selection for any reason. Press this key once to clear data not yet

entered.

NOTE – Use the CLEAR/STOP key to stop the running belt should you encounter difﬁculty or need to stop quickly during an

exercise.

NUMERIC KEYPAD: Use Numeric keys to enter exercise time, belt speed, weight, distance and target heart rate.

NOTE – These keys also become Quick Speed keys during a program because they can be used to enter directly the speed

(whole numbers) you want to reach without having to use the SPEED INCREASE or DECREASE keys. You just need to select

the speed with the numeric keypad keys and press the ENTER key at the top on the right hand side of your computer

display monitor. However, if you want to go to 6.5 mph, you need to push 6 and press the ENTER key, you will see your

entries on the central information window. Then, with the INCREASE Speed key, go from 6 mph to 6.5 mph.

ENTER KEY: Press this key to accept entries of workout setup values.

NOTE – To enter data, you could use either the JustGo^TM/ENTER key or the green “ENTER” key at the top on the right

hand side of your computer display monitor.

COOL DOWN: Press this key to begin an automatically customized workout cool-down.

PAUSE: Press this key to stop the belt and hold the current workout.

Download from Www.Somanuals.com. All Manuals Search And Download.

Scanning Feature

During an exercise you will be able to view nine scanning exercise parameters on the central informational window along

with the exercise program. The parameters that will be displayed are:

• DISTANCE is shown in miles or kilometers for the entire exercise.

• CALORIES indicates the caloric expenditure based on your actual exercise.

• PACE is shown in minutes and seconds.

• ELEVATION is shown % of elevation.

• HEART RATE displays your actual heart rate if the optional chest strap is used. The display is shown in beats per

minute.

• TREM (time remaning) indicates the amount of time left once a program has started.

or DIST. REM (distance remaining) if you chose distance in your settings

or CAL. REM (calories remaining) if you chose calories in your settings.

• CAL./HOUR (calories per hour) indicates the hourly caloric expenditure based on your actual exercise.

• SPEED displays the actual speed in miles per hour or kilometers per hour.

All these parameters scroll on the central informational window.

1.2 Pausing During an Exercise

You can pause any exercise by pressing the PAUSE key. When this key is pressed during an exercise, the motor will stop and

the running belt will slow down to 0 mph (0 km/h) within a few seconds. The stop is gradual, allowing the user to come

safely to a complete stop. The elevation will remain at the level just prior to the pause.

To pause an exercise:

1. Press the PAUSE key whenever you feel the need to stop the exercise or if you need to momentarily pause the exercise.

A message will appear on the screen indicating the amount of time remaining in the pause. The pause countdown

will only start once the running belt has come to a complete stop.

2. If you wish to continue the exercise, simply press the JustGo^TM/ENTER key to start the running belt.

3. If you wish to cancel the exercise during the pause, simply press the CLEAR/STOP key. The exercise will be terminated and

a summary of your exercise parameters plus the option to save the exercise will be displayed. If your pause is over the

duration of the pause time, the exercise will terminate automatically.

1.3 Saving an Exercise (custom programs)

Once any program is ﬁnished or is prematurely terminated, the user has the option to save 25 elevations and speed levels

and recall it at a later date. This feature is very useful when a particular exercise is interesting and motivational. With

the T700, you have the ability to create or modify an existing program and save it with the ability to recall it including the

heart rate control program. The T700 has the unique feature of saving a heart rate control program and being able to recall

this exercise and do it without the chest strap.

Saving an exercise program allows the computer to store 25 speed and elevation changes made during your exercise. The

speed and elevation levels saved are the ones before it moves to the next segment. With the T700, you have the ability to

create or modify an existing program (personalize) and save it with the ability to recall it.

When any program is ﬁnished or is prematurely terminated, the exercise parameters will ﬁrst appear and then a menu will

be displayed in which you have the option to save the exercise. The option will be displayed as “TO SAVE THIS EXERCISE

PRESS ENTER IF NOT PRESS STOP”.

If you wish to save the exercise at the end of the program: (The T700 treadmill has eight custom program slots)

1. Press the JustGo^TM/ENTER key while your parameters are scrolling.

2. The T700 will indicate to you under which CUSTOM number it has been saved.

NOTE – If the memory is full press the INCREASE or DECREASE keys to select the CUSTOM program you would like to

overwrite. Press the JustGo^TM/ENTER key to accept.

If you do not wish to save the exercise, press the CLEAR/STOP key to return to the welcome screen.

NOTE – You will need to turn on the SAVING OPTION to have the ability to save programs.

Download from Www.Somanuals.com. All Manuals Search And Download.

1.4 Viewing Exercise Parameters

At the end of each exercise program, the computer will display four exercise parameters. These parameters will be TOTAL

DISTANCE, CALORIES BURNED, TOTAL EXERCISE TIME, and AVERAGE SPEED.

• TOTAL DISTANCE displays the distance travelled for the entire exercise.

• CALORIES BURNED displays the approximate caloric expenditure for the entire exercise.

• TOTAL EXERCISE TIME displays the length of the exercise in minutes and seconds.

• AVERAGE SPEED displays the average speed value for the entire exercise.

The total exercise parameters on the T700 will loop for 2 minutes, showing your exercise parameters until you press

CLEAR/STOP to exit back to the welcome screen. If you do not wish to view the exercise parameters, press the CLEAR/STOP

key to return to the welcome screen.

1.5 Fitness Networking (Cardio Theater^®, Fit Linxx^®)

Your treadmill is equipped with a RJ45 type connector located on the back of your display console.

This network port allows your treadmill to be connected to a ﬁtness entertainement system such as the

Cardio Theater^®or a ﬁtness network such as Fit Linxx^®(using CSAFE Protocol).

Setting Up the Computer

to Your Environment

o Your Environment

tting Up the Computer

The T700 treadmill offers unique features that allow the user to tailor the treadmill to its current environment. The

treadmill computer can also display a series of diagnostic features and calibration features.

T700 treadmill allows you to select and modify the following settings:

• Language (English, French, Spanish)

• Distance Unit (Miles or Kilometers)

• User ID

• Speed Limits

•

Weight Unit (Pounds or Kilograms)

• Warm Up (On or Off)

Cool Down (On or Off)

•

Pause Time

Big Number Option

•

• Edit Text

• Heart Rate Control Options

• Maximum duration

• Add/Remove Program

• Learn Program

•

Sound (On or Off)

Heart Rate Access Options

• Time, Distance or Calories

• Saving Option (On or Off)

2.1 Access to ”Settings Menu”

To view the above settings, you must enter into the “SETTINGS MENU” as followed:

1. Turn power ON.

2. While the introduction screens are displayed, simultaneously hold down the elevation INCREASE and the SELECT TOP keys.

3. Release the ELEVATION INCREASE and the SELECT TOP keys once entered into the Settings menu.

2.2 Language Feature

You can display all the instructions and information on the computer display screen in a choice of three languages.

To select a language: Enter into the Settings menu, see Section 2.1.

1. Select the LANGUAGE option, and press the JustGo^TM/ENTER key to accept.

2. Select the language you wish to be displayed on the screen. Choose from English, French and Spanish. Press the INCREASE

or DECREASE keys to select the language.

3. Press the JustGo^TM/ENTER key to accept.

From now on, all text will be displayed in the language you selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.3 Distance Unit Feature

The distance unit can be selected to display in miles or kilometers.

To select a distance unit: Enter into the Settings menu, see Section 2.1.

1. Select the DISTANCE UNIT option, and press the JustGo^TM/ENTER key to accept.

2. Select the distance unit you wish to be displayed on the screen. Choose from MILES or KILOMETERS. Press the INCREASE

or DECREASE keys to select the distance unit.

3. Press the JustGo^TM/ENTER key to accept.

From now on, distance and speed values entered will be in the selected units.

2.4 Weight Unit Feature

The weight unit can be selected to display in pounds or kilograms.

To select a weight unit: Enter into the Settings menu, see Section 2.1.

1. Select the WEIGHT UNIT option, and press the JustGo^TM/ENTER key to accept.

2. Select the weight unit you wish to be displayed on the screen. Choose from POUNDS or KILOGRAMS. Press the INCREASE

or DECREASE keys to select.

3. Press the JustGo^TM/ENTER key to accept.

From now on, weight values entered will be in the selected units.

2.5 Warm Up and Cool Down Feature

Doing a warm up period before an exercise and a cool down period after an exercise is strongly recommended for your

safety. In your T700, you have a feature that will allow you to warm up and cool down on your treadmill.

If the warm up or cool down option is activated, a warm up screen will be displayed prior to each exercise as well as a cool

down screen after each exercise. Be aware that the warm up and cool down screens are not available for the JustGo^TM

program in which you need to establish your own warm up and cool down periods.

The warm up has an adjustable duration of one to four minutes and that period is divided in 3 parts.

Warm up:

Part 1: Is 40% in intensity of the ﬁrst segment exercise.

Part 2: Is 60% in intensity of the ﬁrst segment exercise.

Part 3: Is 80% in intensity of the ﬁrst segment exercise.

NOTE – The default value of the warm up is 3 minutes.

The cool down has an adjustable duration of one to four minutes and has only one part.

Cool down:

Part 1: Is a half in intensity of the last segment exercise with a maximum of 3.5 mph (5.6 km/h).

NOTE – The default value of the cool down is 3 minutes.

The calories, time and the distance are not accumulated in the “WARM UP OR COOL DOWN” modes.

The warm up or cool down option can be activated or deactivated separately.

To activate or deactivate the warm up or cool down option: Enter into the Settings menu, See Section 2.1.

1. Select the WARM UP or COOL DOWN option, and press the JustGo /ENTER key to accept.

2. Choose from ON or OFF. Press the speed INCREASE or DECREASE to choose and press the JustGo^TM/ENTER key to accept.

3. To adjust the duration of the warm up or cool down, use the speed keys.

From now on, the warm up or cool down option will be in the selected mode.

NOTE – If you wish to cancel the warm up or cool down while you perform it, simply press the CLEAR/STOP key to interrupt

the feature.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.6 Heart Rate Control Options Feature

The heart rate control feature lets you choose from three different operating modes. The ﬁrst mode is “SPEED AND

ELEVATION MODE”. In this mode, the machine will bring you to your target heart rate by doing changes in speed and

elevation, but you can make your own changes at anytime. The second mode is “SPEED MODE”. In this mode, the machine

will bring you to your target heart rate by changing the speed but it will let you do any change manually at any time. The

computer will adjust the speed to keep you in your target heart rate. The third mode is “ELEVATION MODE”. In this mode,

the machine will bring you to your target heart rate by changing the elevation but it will let you do any change manually

at any time. The computer will adjust the elevation to keep you in your target heart rate. Note that the default mode is

“SPEED AND ELEVATION MODE”.

To select the mode you want to choose: Enter into the Settings menu, see Section 2.1.

1. Select HEART RATE CONTROL option and press the JustGo^TM/ENTER key to accept.

2. Press the INCREASE or DECREASE keys to select the mode you want to choose and press the JustGo^TM/ENTER key to

accept. The computer will indicate to you the mode you have just chosen and it will be active from now on.

2.7 Beeper Feature

The sound can be activated or deactivated.

To activate or deactivate the sound:

1. Enter into the Settings menu, see Section 2.1.

2. Select the SOUND option, and press the JustGo^TM/ENTER key to accept.

3. Select the mode in which you wish the sound to be. Choose ON or OFF with the SPEED keys and press JustGo^TM/ENTER

key to accept.

4. If “ON” mode is chosen, adjust the sound volume with the SPEED keys and press JustGo^TM/ENTER.

From now on, the sound will be in the selected mode.

2.8 Heart Rate Access Options Feature

The Heart Rate Access Options feature lets you choose from two different operating modes. The ﬁrst mode is “SPEED

MODE”. In this mode, the machine will bring you to your target heart rate by changing the speed but it will let you do any

change manually at any time. The computer will adjust the speed to keep you in your target heart rate. The second mode

is “ELEVATION MODE”. In this mode, the machine will bring you to your target heart rate by changing the elevation but it

will let you do any change manually at any time. The computer will adjust the elevation to keep you in your target heart

rate. Note that the default mode is “SPEED MODE”.

To select the mode you want to choose: Enter into the Settings menu, see Section 2.1.

1. Select HEART RATE ACCESS OPTIONS and press the JustGo^TM/ENTER key to accept.

2. Press the INCREASE or DECREASE keys to select the mode you want to choose and press the JustGo^TM/ENTER key to

accept. The computer will indicate to you the mode you have just chosen and it will be active from now on.

2.9 Time, Distance, Calories Feature

The TIME, DISTANCE or CALORIES feature allows you to display either time, distance, calories or any of them as your

exercise target.

To access TIME, DISTANCE or CALORIES: Enter into the Settings menu, see Section 2.1.

1. Select the TIME, DISTANCE or CALORIES menu with the INCREASE or DECREASE keys and press the JustGo^TM/ENTER

key to enter it.

2. Make your choice between time, distance, calories or all with the INCREASE or DECREASE keys and press the

JustGo^TM/ENTER key to accept it.

From now on, the new value of your exercise will be in the selected value.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of minimum and maximum values

Here’s a table of the minimum and the maximum values that you can choose as a duration depending on your Settings

choice.

TIME

DISTANCE

CALORIES

MIN

5 minutes

1 mile or 1 km

25 calories

MAX

99 minutes

99 miles or 99 km

2000 calories

2.10 User Identiﬁcation Feature

The User Identiﬁcation feature allows the treadmill to recognize individuals and automatically enter their weight along with

additional information. The T700 will recognize eight.

Whenever the User Identiﬁcation feature is used, the weight will be automatically entered at each exercise program.

Therefore, user weight will not be asked during the program set up. Also, the user’s age will be automatically entered during

the Heart Rate Control program to calculate the maximum heart rate.

The User ID feature gives access to the following options:

• ACTIVATE USER ID

• CREATE USER ID

• VIEW STATISTICS

• EDIT USER ID

• RESET STATISTICS

• DELETE USER ID

Activate User

To activate the User Identiﬁcation feature: Enter into the Settings menu, see Section 2.1.

1. Select the USER ID option and press the JustGo^TM/ENTER key to accept.

2. Select the ACTIVATE USER ID option and press JustGo^TM/ENTER key to accept.

3. Press INCREASE or DECREASE key to choose ON or OFF to activate or deactivate it and then press the JustGo^TM/ENTER key

to accept.

Now that the User ID feature is activated; you will be prompted, at the beginning of each program, to select a User

Identiﬁcation.

Create User

To create a User ID’s:

1. Enter into the Settings menu, see Section 2.1.

2. Select the USER ID option and press the JustGo^TM/ENTER key to accept.

3. Select the CREATE USER option and press JustGo^TM/ENTER key to accept.

4. You will immediately be sent to the lowest empty location, if the MEMORY is full you will have to go to the DELETE USER

option.

5. A total of six alpha-numeric characters can be used to name the USER ID. Use the INCREASE or DECREASE keys to select

any letter from A to Z or number from 0 to 9 as the ﬁrst character. If you wish to leave a space between characters, simply

select SPACE (blank character) between the 9 and the A characters. Press the JustGo^TM/ENTER key to accept this character.

Now the second character must be selected. Repeat this procedure until you have selected a USER ID name.

Download from Www.Somanuals.com. All Manuals Search And Download.

If you wish to modify a character before all six spaces are accepted, press the CLEAR/STOP key to backspace.

6. Now you have to enter your age. Simply use the QUICK key to select your age. Press the JustGo^TM/ ENTER key to accept

your age.

7. Enter your weight, press the INCREASE or DECREASE key to select your weight from 50 to 400 pounds (23 to

182 kilograms) and then press the JustGo^TM/ENTER key to accept it.

8. Then press the CLEAR/STOP key to go back to the USER ID main menu.

Edit User

To edit the different User ID’s: Select the USER ID option and press the JustGo^TM/ENTER key to accept.

1. Select the user you want to edit by using the INCREASE or DECREASE key and press the JustGo^TM/ENTER key to accept it.

2. Enter your weight, press the INCREASE or DECREASE key to select your weight from 50 to 400 pounds (23 to 182 kg) and

then press the JustGo^TM/ENTER key to accept it.

3. Now you have to enter your age. Simply use the INCREASE or DECREASE key to select your age. Press the JustGo^TM/ENTER

key to accept your age.

4. Press the CLEAR/STOP key to go back to the USER ID main menu.

View Statistics

To view the statistics of a User Identiﬁcation: Select the VIEW STATISTICS option and press JustGo^TM/ENTER key to accept.

Select the User Identiﬁcation for which you wish to see the statistics. These parameters represent the accumulated values of

all the exercises of a user while the User Identiﬁcation feature was activated.

• TOTAL DISTANCE displays the distance traveled in miles (or in kilometers depending on your settings).

• TOTAL CALORIES displays the accumulated calories expended.

• TOTAL TIME displays the total exercise time.

Reset Statistics

To reset the statistics of a User Identiﬁcation: Select the RESET STATISTICS option and press JustGo^TM/ENTER key to accept.

Select the User Identiﬁcation for which you wish to reset the statistics. Press the JustGo^TM/ENTER key to reset the statistics of

this User Identiﬁcation.

If you do not wish to reset the statistics of this User Identiﬁcation, press the CLEAR/STOP key. The Reset Statistics feature can

help to monitor your progress week after week or between seasons.

Delete User

To delete a User Identiﬁcation: Select the DELETE USER option and press JustGo^TM/ENTER key to accept.

Select the User Identiﬁcation you wish to delete. Press the JustGo^TM/ENTER key to delete this User Identiﬁcation.

If you do not wish to delete this User Identiﬁcation, press the CLEAR/STOP key.

NOTE – If you choose to delete a user, you will clear all saved parameters under that user’s name.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.11 Speed Limits

MINIMUM and MAXIMUM speeds can be set into the treadmill.

Minimum:

Maximum:

Default:

0.1 MPH(0.16 KM/H)

15 MPH (24.00 KM/H)

To select this option: Enter into the Settings menu, see Section 2.1.

0.5 to 15 MPH (0.8 to 24.00 KM/H)

1. Select the SPEED LIMITS option, and press the JustGo^TM/ENTER key

to accept.

2. Select the MINIMUM OR MAXIMUM value with the ELEVATION INCREASE AND ELEVATION DECREASE keys. To modify

the value, use the SPEED INCREASE OR DECREASE keys. Press the JustGo^TM/Enter key to accept (the values will not be

considered if you don’t press the ENTER key to accept).

Please refer to the following values to know the possible range of values.

2.12 Pause Time

To modify the pause time: Enter into the Settings menu, see Section 2.1.

1. Select the PAUSE TIME option, and press the JustGo^TM/ENTER key to accept.

2. Select from 1 to 5 minute pause times. Press the INCREASE or DECREASE keys to select the pause time.

3. Press the JustGo^TM/ENTER key to accept.

2.13 Big Number Option

The big number option allows you to display LARGE numbers on the main screen. Proﬁle will not be shown in this mode.

The big number option can be activated or deactivated. While in this option, you can select 7 different ways of display.

To select a big number option: Enter into the Setting menu, see section 2.1.

1. Select the BIG NUMBER OPTION, and press the JustGo^TM/ENTER key to accept.

2. Select the option you wish to be displayed on the screen. Choose from, NONE, All, Speed, Distance, Calories, Time or

Heart Rate. Press the INCREASE or DECREASE key to select the option.

3. Press the JustGo^TM/ENTER key to accept.

From now on, all the information will be displayed on screen as the option you selected.

NOTE – All the programs will be displayed in Big Numbers except for the Track and the Runner’s Interval programs.

2.14 Edit Text Feature

The Edit Text feature allows the owner or users of the treadmills to modify the welcome message displayed on the main

computer display screen.

There is a standard welcome message entered in your T700. This message is displayed in the language of your choice

previously selected (refer to Section 2.2). If the standard message is modiﬁed, it will only be displayed in the language you

entered.

To activate the Edit Texte feature: Enter into the Settings menu, see section 2.1.

1. Select the EDIT TEXT option, and press the JustGo^TM/ENTER key to accept.

To modify the welcome message, you will need to enter the letters and characters one by one. A total of 200 alpha-

numeric characters can be saved.

2. Use the INCREASE or DECREASE keys to select any letter from A to Z or number from 0 to 9 as the ﬁrst character. If you

wish to leave a space between characters, select SPACE (blank character) between the 9 and the A characters. Press the

ELEVATION DECREASE key to move to the next character. Now the second character must be selected. Repeat this

procedure until you have entered the new welcome message. If you wish to modify a character before all 200 spaces are

accepted, press the ELEVATION INCREASE key to backspace.

3. Once all letters and characters of your message are entered, press SAVE on the informational window to save your

message.

From now on, your new welcome message will be displayed on the introduction screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.15 Max Duration

To modify the maximum duration of any workout: Enter into the Settings menu, see Section 2.1.

1. Select the MAX DURATION option, and press the JustGo^TM/ENTER key.

2. Use the Speed INCREASE or DECREASE keys to choose from TIME, DISTANCE or CALORIES. Press the JustGo^TM/ENTER key

to accept.

3. Use the Speed INCREASE or DECREASE keys to adjust the maximum to the desired value (5 to 99 minutes for Time,

0.5 to 99 miles or km for distance or 25 to 2000 calories). Press the JustGo^TM/ENTER key to accept.

2.16 Add/Remove Program

The T700 treadmill offers you the possibility to manage your main menu with your favorite programs by deleting from the

menu on the screen the programs that you would rather not have on screen. After deleting it, you can, if you changed your

mind, put it back to your menu with the add option.

To select the add/remove program feature: Enter the Settings menu, see Section 2.1.

1. Select the ADD/REMOVE PROGRAM feature with the INCREASE or DECREASE keys and press the JustGo^TM/ENTER key to

accept.

2. Using the INCREASE or DECREASE keys, select YES in front of the program name you want to add or keep and select NO

in front of the programs you want to remove. Press the JustGo^TM/ENTER key to accept.

NOTE – You cannot remove the program that appears on the console and the JustGo^TMProgram.

2.17 Learn Program

Bodyguard machines have the incredible ability to learn (pre-program) proﬁles. This is especially useful if you would like to

build a workout proﬁle in advance. You now have the ability to build a program without actually doing it. This is great if

you are customizing a program for a client for example.

To use learn program: Enter into the Settings menu, see section 2.1.

1. You will be prompted to a screen that will ask you to increase or decrease either Speed and Elevation.

Adjust both parameters and look at the side select windows where you are going.

2. Once you are satisﬁed press ENTER to lock it and move to the next SEGMENT.

3. Repeat this procedure until the whole proﬁle has been ﬁlled in.

- You can learn 8 programs in the T700.

- To use a LEARN program, choose LEARN from the program selection window.

2.18 Saving Option (On or Off)

To modify the saving possibility at the end of a program: Enter into the Settings menu, see Section 2.1.

1. Select the SAVING OPTION, and press the JustGo^TM/ENTER key to accept.

2. Use the Speed INCREASE or DECREASE keys to choose from ON or OFF.

3. Press the JustGo^TM/ENTER key to accept.

Download from Www.Somanuals.com. All Manuals Search And Download.

T700

Exercise Programs

•

Ten Program Levels

One JustGo^TMProgram

One Manual Program

One Cardiovascular Program

Interval Program

One Random Program

One Weight Loss Program

One Heart Rate Control Program

One Walk Program

•

One Hill Climb Program

One Speed Run Program

One Track Program

Runner’s Interval Program

One Hills & Valleys Program

One Gerkin Protocol Program

Eight Memory Programs

Eight Learn Programs

Heart Rate Access Feature

A program is a pre-set hill pattern. You will get the same proﬁle (hills and valleys) every time you select the same speciﬁc

exercise program. By increasing the levels you can change the predetermined hill proﬁles. The programs allow you to

monitor your progress and they add fun and interest to your exercise.

Each segment time is equal to the selected exercise time divided by 25 segments. Therefore, a 75 minute exercise results in

a 3 minute segment time.

W A R N I N G

BEFORE SELECTING ANY EXERCISE PROGRAM, FIRST STRADDLE YOUR FEET

ON THE FOOT RESTS. NEVER START ANY EXERCISE PROGRAM

WITH ONE OR BOTH FEET ON THE RUNNING BELT.

Program Levels

The Cardiovascular, Interval, Random, Hill Climb, Speed Run and Hills & Valleys programs have 10 individual exercise levels.

LEVEL 1 is the easiest and LEVEL 10 is the most difﬁcult. This feature allows you to alter the intensity of your workout.

JustGo^TMProgram

The JustGo^TMprogram allows you to start a manual exercise with the push of one key. Since the JustGo^TMprogram is the

initial program, it will always be displayed ﬁrst for easy selection. You have total control of the speed and elevation of the

belt at all times during this program. Use the JustGo^TMprogram if you like to walk or run at fairly constant speeds with little

or no changes during the exercise.

During the exercise, the speed and elevation that you select will remain for the entire exercise until the next change you

make. Your progression in the exercise is shown by one ﬂashing dot.

To start exercising in the JustGo^TMprogram:

1. Press the JustGo^TM/ENTER key when the JustGo^TMprogram is displayed on the screen. The running belt will slowly start

at 0.5 mph or 0.8 km/h and at 0% elevation with the exercise duration automatically set to the maximum.

The JustGo^TMprogram does not allow the user to predetermine the exercise duration or enter a weight amount.

Therefore, the caloric expenditure and calories per hour values will be based on a user of 150 pounds or 68 kilograms.

The calorie values should therefore be used only as references when in the JustGo^TMprogram.

2. Change the speed and elevation at all times by pressing the respective Speed and Elevation INCREASE and DECREASE keys.

3. You can pause, resume, end the program and save the program at anytime. It is not necessary to exercise the full

duration to save the program.

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual Program

The Manual program allows you to create your own exercise as you progress in the program. The speed and elevation

are completely controlled by the user at all times. At a glance, the JustGo^TMand Manual programs seem very similar due to

the fact that the user controls both the speed and elevation at all times. The difference is that in the Manual program, you

can select your exercise duration and weight for a more accurate display of the calories.

During the exercise, the speed and elevation that you select will remain for the entire exercise until the next change you

make. Your progression in the exercise is shown by one ﬂashing dot.

Cardiovascular Program

The Cardiovascular program has been designed to allow you to train at moderate intensity levels with short duration,

high intensity periods followed by a quick recovery period. The Cardiovascular program has predetermined speed and

elevation proﬁles according to the selected exercise levels. You can change the speed and elevation during the exercise if

you ﬁnd it too easy or hard.

The speed proﬁle has a set of high intensity segments to greater work your heart muscles. Changing the speed manually will

cause only that segment to change. Changing the elevation manually will cause the entire proﬁle to change.

The following table shows the different speeds and elevations for each level.

Level

Speed (mph)

Speed (km/h)

Elevation (%)

1.0 to 2.0

2.0 to 3.0

2.0 to 4.0

3.0 to 4.0

4.0 to 5.0

4.0 to 6.0

5.0 to 7.0

5.0 to 8.0

6.0 to 8.0

7.0 to 8.0

1.6 to 3.2

3.2 to 4.8

3.2 to 6.4

4.8 to 6.4

6.4 to 8.0

6.4 to 9.6

8.0 to 11.2

8.0 to 12.8

9.6 to 12.8

11.2 to 12.8

0.0 to 2.0

0.0 to 3.0

0.0 to 4.0

0.0 to 5.0

0.0 to 6.0

Interval Program

The Interval Training program allows you to exercise with constant high intensity workouts and rest periodically at set

recovery periods. The Interval Training program has predetermined speed and elevation proﬁles according to the selected

exercise levels. You can change the speed and elevation during the exercise if you ﬁnd it too easy or hard.

If you are at a rest (low intensity) segment, then changing the speed manually will cause all the other segments to change.

If your are at a peak (high intensity) segment, then changing the speed manually will cause all the peak segments to

change. Changing the elevation manually will cause the entire elevation proﬁle to change.

The following table shows the different speeds and elevations for each level.

Level

Speed (mph)

Speed (km/h)

Elevation (%)

0.5 to 2.0

1.0 to 3.0

1.0 to 4.0

1.0 to 5.0

2.0 to 5.0

3.0 to 5.0

3.0 to 6.0

4.0 to 6.0

4.0 to 7.0

5.0 to 8.0

0.8 to 3.2

1.6 to 4.8

1.6 to 6.4

1.6 to 8.0

3.2 to 8.0

4.8 to 8.0

4.8 to 9.6

6.4 to 9.6

6.4 to 11.2

8.0 to 12.8

0.0 to 1.0

0.0 to 2.0

0.0 to 3.0

1.0 to 4.0

1.0 to 5.0

1.0 to 6.0

2.0 to 6.0

2.0 to 7.0

Download from Www.Somanuals.com. All Manuals Search And Download.

Random Program

The Random program will display a completely new exercise each time the Random program is selected. This unique

feature allows an almost inﬁnite amount of exercise programs to be displayed at the touch of a key. Each new Random

program will have a programmed speed and elevation proﬁle, resulting in automatic speed and elevation changes. If you

wish, you can change the speed or elevation at anytime during the exercise. The computer can display over 4 billion

random programs.

The following table shows the different speeds and elevations for each level.

Level

Speed (mph)

Speed (km/h)

Elevation (%)

0.5 to 2.0

1.0 to 3.0

2.0 to 4.0

2.0 to 5.0

3.0 to 5.0

3.0 to 6.0

4.0 to 6.0

4.0 to 7.0

5.0 to 7.0

5.0 to 8.0

0.8 to 3.2

1.6 to 4.8

1.6 to 6.4

3.2 to 8.0

4.8 to 8.0

4.8 to 9.6

6.4 to 9.6

6.4 to 11.2

8.0 to 11.2

8.0 to 12.8

0.0 to 1.0

0.0 to 2.0

0.0 to 3.0

0.0 to 4.0

1.0 to 5.0

2.0 to 6.0

2.0 to 7.0

2.0 to 10.0

3.0 to 12.0

Heart Rate Control Program (HRC) and Weight Loss Program

(Requires wireless chest strap)

The Heart Rate Control and Weight Loss programs allow you to exercise at a predetermined heart rate level. By selecting

the desired heart rate level (Weight Loss in Weight Loss program), the running belt and elevation will automatically adjust

to decrease or increase the exercise intensity.

By selecting your age, plus the intensity level that you want to work your heart at (Only HRC), a target heart rate level is

calculated by the computer.

CARDIOZONE: The T700 treadmill comes with NEW cardiozone software. Cardiozone is the ability to see on-screen

effective heart-rate training. Cardiozone will show a bar on the main screen that visually shows whether you are in your fat

loss, healthy heart or cardio training zone from any program.

NOTE – This program can only be used with the optional heart rate chest strap available from your Authorized Bodyguard^®

Dealer. Use of the heart rate chest strap will allow the treadmill belt to change speed along with a change in elevation. To

achieve optimal results, it is recommended to place the chest strap directly over the skin. The strap should be very snug since

any signiﬁcant amount of shock or impact due to fast running may temporarily produce wrong heart rate signals. You should

not be more than arm’s length from the front handle bar to achieve the best signal. If at anytime the heart rate receiver does

not detect a signal from the chest strap for more than a few seconds, the following message will appear ‘‘UNSTABLE HR

SIGNAL PLEASE CHECK CHEST STRAP’’.

WARNING – Before attempting to use any of this equipment, you should read the instruction manual carefully. Use of

this equipment by people with heart or other medical problems may result in serious injury. You should consult with a

physician prior to using this equipment. It is recommended to periodically consult your physician as you continue to use this

equipment. Immediately cease exercise if you feel dizzy, faint or short of breath. Use of this equipment in a manner other

than as prescribed by these instructions herewith may result in serious injury.

To select the Heart Rate Control program or Weight Loss program:

1. Press the HEART RATE or WEIGHT LOSS key. Press the JustGo^TM/ENTER key to accept.

2. Select your weight. Press the Speed INCREASE or DECREASE key or use the numeric keypad to select the appropriate

weight. Press the JustGo^TM/ENTER key to accept.

3. Select the exercise goal type. Press the Speed INCREASE or DECREASE key to choose: time, calories or distance. Press the

JustGo^TM/ENTER key to accept.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Enter exercise goal (number of calories, duration or distance). Press the JustGo^TM/ENTER key to accept.

5. Select your age to allow the computer to indicate your maximum allowable heart rate level. Press the Speed INCREASE

or DECREASE key to select your age. The age will vary from 10 to 100 years. Press the JustGo^TM/ENTER key to accept.

6. Select an exercise intensity based on your preferred level of exercise. The 60% level is a good guide for those interested

in training in the fat loss range. The 70% level is suitable for those interested in training in the cardiovascular range. The

80% level requires the most effort and is suitable for persons with a higher level of ﬁtness. Press the JustGo^TM/ENTER key

to accept the intensity (60% is a default in Weight Loss Program).

7. You can modify the heart rate level suggested by the computer or press the JustGo^TM/ENTER key to accept it and start

the exercise.

8. To start the exercise, press the JustGo^TM/ENTER key.

During the Heart Rate Control or Weight Loss program, you can change the speed or elevation by pressing the Speed or

Elevation INCREASE or DECREASE keys. Keep in mind that the computer will then gradually readjust the speed and/or

elevation to compensate for the change in speed or elevation you made by gradually bringing your ACTUAL heart rate near

the TARGET heart rate level.

WARNING – If you feel that the running belt is moving too fast for your ﬁtness level and you cannot keep up, press the

CLEAR/STOP key and terminate the exercise program. You can try the program again, but at a lower INTENSITY level

(60%). If this is still too fast for you, do not use the Heart Rate Control program until your ﬁtness level allows you to

safely exercise at your TARGET heart rate level.

During the exercise, the main computer screen will show a speed or elevation proﬁle like the other programs, but will display

your ACTUAL heart rate and your TARGET heart rate on the message center. Once the exercise has started, your ACTUAL

heart rate should be lower than the TARGET heart rate. The computer then will gradually regulate the speed and elevation

simultaneously to increase your exercise intensity level, resulting in a higher ACTUAL heart rate.

Your heart rate will be displayed on the message center as ACTUAL heart rate and TARGET heart rate (T). For example:

HRATE 110/115T.

NOTE – You can change your target heart rate while in the program by pressing the JustGo^TM/ENTER key and modify it by

using the Speed DECREASE or INCREASE keys and by pressing the JustGo^TM/ENTER key to accept it.

Walk Program

The Walk program allows you to create your own exercise as you progress in the program. The speed and elevation are

completely controlled by the user at all times. At a glance, Manual and Walk programs seem very similar due to the fact that

the user controls both the speed and elevation at all times. The difference is that in the Walk program, you can’t go over

4.0 mph (6.4 km/h) and 6% of elevation.

During the exercise, the speed and elevation that you select will remain for the entire exercise until the next change you

make. Your progression in the exercise is shown by the ﬂashing dot.

To select the Walk program:

Press the OTHER PROGRAMS key or the DECREASE key until you reach the Walk program. Press the JustGo^TM/ENTER key

to accept and follow the instructions shown in the central information window.

Hill Climb Program

The Hill Climb program provides both a programmed hill

and speed proﬁles. The programmed hill proﬁle will cause

SELECT

ELAPSED TIME

the running belt to elevate and descend at various points

TARGET REMAINING

PACE

during your exercise. The programmed speed proﬁle will

SPEED

DISTANCE

cause the speed to change. You can change the speed and

elevation during the exercise if you ﬁnd it too easy or

ELEVATION

CALORIES

CAL

HOUR

HEART RATE

hard.

The speed and elevation will change as you progress into

the program. Changing the speed manually will cause

only that segment to change. Changing the elevation

manually will cause the entire elevation proﬁle to change.

ﬁgure 7

Download from Www.Somanuals.com. All Manuals Search And Download.

The following table shows the different speeds and elevations for each level.

Level

Speed (mph)

Speed (km/h)

Elevation (%)

0.5 to 2.0

1.0 to 3.0

2.0 to 4.0

2.0 to 5.0

3.0 to 5.0

3.0 to 6.0

4.0 to 6.0

4.0 to 7.0

5.0 to 7.0

5.0 to 8.0

0.8 to 3.2

1.6 to 4.8

1.6 to 6.4

3.2 to 8.0

4.8 to 8.0

4.8 to 9.6

6.4 to 9.6

6.4 to 11.2

8.0 to 11.2

8.0 to 12.8

0.0 to 1.0

0.0 to 2.0

0.0 to 3.0

0.0 to 4.0

1.0 to 5.0

2.0 to 6.0

2.0 to 7.0

2.0 to 10.0

3.0 to 12.0

To select the Hill Climb program:

Press the OTHER PROGRAMS key or the DECREASE key until you reach the Hill Climb program. Press the JustGo^TM/ENTER

key to accept and follow the instructions shown in the central information window.

Speed Run Program

The Speed Run program like the Hill Climb program controls a certain parameter. Speed Run is speed changes. Selecting a

higher level will default a higher speed proﬁle. Elevation changes are user controlled.

The speed will change as you progress into the program. Changing the speed or elevation manually will cause the rest of

the program to change.

The following table shows the different speeds for each level.

Level

Speed (mph)

Speed (km/h)

Elevation (%)

1.0 to 4.0

1.0 to 5.0

2.0 to 6.0

2.0 to 6.5

3.0 to 7.0

3.0 to 7.2

4.0 to 8.0

4.0 to 8.5

5.0 to 9.5

5.0 to 10

1.6 to 6.4

1.6 to 8.0

3.2 to 9.6

3.2 to 10.4

4.8 to 11.2

4.8 to 11.5

6.4 to 12.8

6.4 to 13.6

8.0 to 15.2

8.0 to 16

0.0

To select the Speed Run program:

Press the OTHER PROGRAMS key or the DECREASE key until you reach the Speed Run program. Press the JustGo^TM/ENTER

key to accept and follow the instructions shown in the central information window.

Track Program

The Track program is one that enables you to choose from

1-99 laps of a 400 Meter (or about a 1/4 mile) Olympic track.

Each Track program allows the user to completely control their

SELECT

ELAPSED TIME

TARGET REMAINING

speed from the start of the exercise until the end since there is

no automatic speed control during the Track program.

PACE

SPEED

DISTANCE

ELEVATION

CALORIES

The Track program will display an oval track screen that will

CAL

HOUR

HEART RATE

show your progression on the track. The central information

window will show you how many laps have been done in your

workout. Elevation although not usually found on any track

can be used on the T700.

ﬁgure 8

Download from Www.Somanuals.com. All Manuals Search And Download.

To select the Track program:

Press the OTHER PROGRAMS key or the DECREASE key until you reach the Track program. Press the JustGo^TM/ENTER key to

accept and follow the instructions shown in the central information window.

Runner’s Interval Program

The Runner’s Interval program is made for serious runners who want to simulate track workouts and create any workout

they choose.

The program enables to select interval distance, number of repeats, Pace, Recovery Time and Recovery Pace wanted.

The parameters values are:

Interval distance: 200, 400, 600, 800, 1000, 1200, 1400 or 1600 meters

Number of repeats: 1 to 20

Pace: number of min. for 1 mile or number of min. for 1 kilometer

Recovery Time: 20 sec. to 20 min.

Recovery Pace: number of min. for 1 mile or number of min. for 1 kilometer

The Recovery Time will count down. The last 3 seconds of the recovery time will appear on the display and an audible beep

will indicate the start of the next interval.

The program will start with a recovery segment, so that you are not starting from a dead stop.

The program will display an oval track of 400 meters that will show your progression on the track.

Example: 8 x 400’s meters @ 5:15 min. Pace with a 1 min. 30 sec. Recovery Time at 15:00 min. Pace.

To select the Runner’s Interval program:

Press the OTHER PROGRAMS key or the DECREASE key until you reach the Runner’s Interval program. Press the

JustGo^TM/ENTER key to accept and follow the instructions shown in the central information window.

WARNING – This is for serious runners only. There is fast acceleration involved…

Hills and Valleys Program

Much like the Hill program, Hills and Valleys program represents a proﬁle that can simulate running through a positive and

negative elevation proﬁle. The program will only change elevations. You can change the speed and elevation during the

exercise if you ﬁnd it too easy or hard.

The elevation will change as you progress into the program. Changing the speed manually will cause the entire speed

proﬁle to change. Changing the elevation manually will cause the entire elevation proﬁle to change.

The following table shows the different elevations for each level.

Level

Speed (mph)

Speed (km/h)

Elevation (%)

2.0

3.2

-2.0 to 1.0

-3.0 to 2.0

-3.0 to 3.0

-3.0 to 5.0

-3.0 to 6.0

-3.0 to 8.0

-3.0 to 9.0

-3.0 to 10.0

To select the Hills and Valleys program:

Press the OTHER PROGRAMS key or the DECREASE key until you reach the Hills and Valleys program. Press the

JustGo^TM/ENTER key to accept and follow the instructions shown in the central information window.

Download from Www.Somanuals.com. All Manuals Search And Download.

Gerkin Protocol Program (Required wireless chest strap)

1. The Gerkin Protocol program (based on Gerkin Protocol) is a graded submaximal V02 test used by the International

Association of Fire Fighters to determine ﬁtness for ﬁre department duty.

2. The test is a series of 1 minute exercise stages, alternating between elevation grade and speed (i.e. ﬁrst minute

elevation is increased, next minute speed is increased, etc.) until the individual heart rate exceeds the target exercise

heart rate.

3. The text ends when the target heart rate is reached and is maintained for 15 seconds. The results are converted in a

V02 MAX value that will be shown in the central information window at the end of the test.

4. The target exercise heart rate is 85 percent of the predicted maximal heart rate for a speciﬁc individual based on age.

To select the Gerkin Protocol program:

Press the OTHER PROGRAMS key or the DECREASE key until you reach the Gerkin Protocol program. Press the

JustGo^TM/ENTER key to accept and follow the instructions shown in the central information window.

Memory & Learn Programs

These programs allow you to recall previously completed or edited exercises. After each exercise is ﬁnished, you are

prompted to save the current exercise or not. All programs, except the Track program can be saved as Memory programs.

The Learn programs are the ones that were previously edited in the Settings menu under Learn programs.

To select an exercise:

Press the Speed DECREASE key to select Memory or Learn programs. Press the JustGo^TM/ENTER key to accept the program.

An edited program will appear on the screen. You can select a particular saved or edited exercise by pressing the Speed

INCREASE and DECREASE keys until the desired name is displayed.

NOTE – By selecting a saved or a Learn program in memory, you cannot enter an exercise level.

Select the exercise duration. Press the Speed INCREASE or DECREASE keys to select the appropriate exercise duration.

Press the JustGo^TM/ENTER key to accept.

Select your weight. Press the Speed INCREASE or DECREASE keys to select the appropriate weight. The weight will vary from

50 to 400 pounds (23 to 182 kilograms). Press the JustGo^TM/ENTER key to accept and start the exercise.

Using Contact Heart Rate

This machine has a built-in Contact Heart Rate System that allows you to verify your heart rate without the need of a

chest strap. By holding the contact bars, you will see your current pulse on screen. (In order for the Contact Heart Rate to

work properly, the palms must not be too moist.)

Heart Rate Access Feature (Requires wireless chest strap)

The Heart Rate Access feature allows you to selectively enter into a Heart Rate Control program without quitting your

exercise. It will allow you to choose, when you are ready, to change your current workout to a Heart Rate Control. You will

need to be wearing the optional wireless chest strap when choosing to use this feature.

The Heart Rate Access feature allows the user to change any program at any time during the selected workout to Heart Rate

Control. On screen, you will see the program remaining change to a ﬂat-line as it would look like in a normal Heart Rate

Control program. The part of the program that you just did though would remain unchanged.

NOTE – You will have to turn on this feature since it is off by default.

How to Use Heart Rate Access™

While in a program you would press the JustGo^TM/ENTER key. On screen you would see the message “Heart Rate Control

Activated” followed by a screen showing your target Heart Rate. Once your Heart Rate has been conﬁrmed, the remainder

of the selected workout time would be in the form of a normal Heart Rate Control. If you pressed the button and were not

wearing a chest strap, the unit would disregard the button push and continue in the normal selected program.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. JustGo^TM, Manual, Walk, Cardiovascular, Random and Interval programs

•

These programs would change SPEED only or ELEVATION only, depending on your selected SETTINGS in Heart Rate

Access options.

2. Speed Run, Track and Runner’s Interval programs

These programs will make SPEED changes only.

3. Hill Climb, Hills and Valleys programs

These programs will make ELEVATION changes only.

4. Memory programs

•

These programs will make changes according to the type of changes that were done in the program that has been

recalled from memory. For example, if you did a Speed Run program and you pressed the JustGo^TM/ENTER

key, you would get SPEED changes only.

5. Override

•

In all programs, you can make SPEED and ELEVATION changes manually.

6. Saving

•

You will also be able to save any program at the end except the TRACK program.

7. Proﬁle

•

You will also be able to see the proﬁle and where the unit made a change to Heart Rate Access.

Changing Your Target Heart Rate in a Program

The normal Heart Rate Control program allows you to make Target Heart Rate changes at anytime while in a program by

pressing the JustGo^TM/ENTER key. The difference is now that by pressing the JustGo^TM/ENTER key, it will bring you into Heart

Rate Access; by pressing the JustGo^TM/ENTER key again, you will be asked to make a new Target Heart Rate change.

CARDIOZONE: The T700 treadmill comes with NEW cardiozone software. Cardiozone is the ability to see on-screen

effective heart-rate training. Cardiozone will show a bar on the main screen that visually shows whether you are in your fat

loss, healthy heart or cardio training zone from any program.

1. If your are wearing a chest strap and want to use cardiozone, press the select top key and select bottom key at the same

time while in a program.

2. On screen you will see “enter age”. Adjust age selection with any up down key and press ENTER to accept. You are now

in cardiozone.

3. HRC (Heart-Rate Control) cardiozone is now active.

The Bodyguard® Heart Rate receiver inside each T700 treadmill is speciﬁcally designed to work in conjunction with the

optional Heart Rate chest strap. The Heart Rate chest strap allows the computer to monitor your heart rate, or pulses per

minute. This value is shown on the computer screen and should only be used as a guide in helping you achieve your

personal ﬁtness goals.

If no Heart Rate chest strap is used, no heart rate value (0) will be displayed on the computer screen. Before using any Heart

Rate chest strap on any exercise equipment, it is important to consult with a physician prior to commencing any exercise

program.

WARNING – Before attempting to use any of this equipment, you should read the instruction manual carefully. Use of

this equipment by people with heart or other medical problems may result in serious injury. You should consult with a

physician prior to using this equipment. It is recommended to periodically consult your physician as you continue to use this

equipment. Immediately cease exercise if you feel dizzy, faint or short of breath. Use of this equipment in a manner other

than as prescribed by these instructions herewith may result in serious injury.

As a guide to effective exercising, to determine your recommended heart rate training zone, ﬁnd your age on the heart rate

chart (refer to page 4) and read the heart rate target zone based on various intensity levels. These levels include fat

burning zone, cardiovascular zone and aerobic zone.

Tip – Sometimes you will need to moisten the back of the heart rate chest strap to obtain a signal. Use a few drops of water

to moisten the chest strap, then place directly over the skin. The chest strap does not work properly when placed over

clothing.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using a Heart Rate Receiver

Using ceiver

Possible Chest Strap Heart Rate Problems

All Bodyguard^®machines are compatible with the Polar wireless heart rate system. This includes a chest strap and a

receiver. The receiver is an integral part of the machine and it is hidden inside. The chest strap is an option on all machines

and can be purchased from Bodyguard^®Polar. If you are having some problems with the reception, please use the following

troubleshooting check list.

Troubleshooting Check List – Table 1

PROBLEM

POSSIBLE CAUSE

SOLUTION

• No signal.

• Dead battery in strap.

• Electrodes are not wet.

• Using wrong strap.

• Change battery.

• Put water on electrodes.

• Use Polar.

• Weak battery.

• Change battery.

• Weak signal.

• Electrodes are not wet enough.

• Strap is not tight enough.

• Too much body fat.

• Put water on electrodes.

• Put on tighter.

• No solution.

• Chest size too small or too big.

• Receiver has a problem.

• Position strap accordingly.

• Verify signal in Diagnostics,

see Heart Rate Test section.

• Using wrong strap.

• Use Polar.

• Interference with other signals.

• Move the machine away from

potential interference sources.

• Erratic signal.

• Electrodes are not wet enough.

• Put water on electrodes.

The above table should help properly diagnose the problem. There is also misconceptions that the signal is immediate.

The chest strap electrodes need to be moistened in order to send a strong signal. Radio and neon light interferences can also

reduce the strength of the signal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Possible Contact Heart Rate Problems

In order to properly diagnose any problem with the conctact heart rate system, please refer to the following procedures.

This machine uses a hand ECG (Electrocardiogram) printed circuit board along with wires and a set of metal plates. The hand

ECG board is an integral part of the machine and is hidden inside.

Troubleshooting Check List – Table 2

SOLUTION

PROBLEM

POSSIBLE CAUSE

• Wait for 15-20 seconds before

a reading

• Hands have not been in contact

with the metal plates long enough

• No reading

• Change ECG board

• Verify Wiring

• Defective hand contact board

• Wires are not connected properly

• Hands may move too much on the plates

• Defective board hand contact board

• Strong neon lights too close to console

• Interference with other signals

• Erratic reading

• Do not move your hands

• Change board

• Move the climber

• Use only this machine to verify

Computer Diagnostics

Access to “Diagnostics” menu

To determine the condition of the various electrical and mechanical components, you will need to enter into the

DIAGNOSTICS menu as follows:

1. Turn power OFF.

2. Simultaneously hold down the speed INCREASE and DECREASE keys and turn power ON.

3. Release the speed INCREASE and DECREASE keys once entered into the Diagnostics menu.

4. Press JustGo^TM/ENTER to access Diagnostic items.

When you access the Diagnostics menu, you will notice the following message: “TXXX VERSION”

The message above indicates the version of the computer software installed in your computer display monitor. This

information is helpful in diagnosing certain computer related conditions. Keep in mind that the version number may

change depending on the model number of your T700 treadmill.

The T700 treadmill allows you to perform the following tests:

• NVRAM TEST

• EPROM TEST

• KEYPAD TEST

• DISPLAY TEST

• SOUND TEST

• HEART RATE TEST

• BELT ALIGNMENT

• MOTOR CHECK

• SPEED SENSOR TEST

• MAINTENANCE

• ELEVATION CALIBRATION

• STATISTICS

•

ERROR LOG

• CURRENT TEST

To perform any one of the above procedures, press the Speed INCREASE or DECREASE keys to select the one you

want and press the JustGo^TM/ENTER key to accept.

Download from Www.Somanuals.com. All Manuals Search And Download.

NVRAM Test

The NVRAM (Non-Volatile Random Access Memory) test will not erase all stored information such as user identiﬁcation, and

all saved programs. The NVRAM is a computer chip that saves information even when the treadmill has been turned off.

1. In the Diagnostics menu, select the “NVRAM TEST” and accept it by pressing the JustGo^TM/ ENTER key.

2. Press the JustGo™/ENTER key to start the NVRAM test. The NVRAM test will perform automatically.

EPROM Test

The EPROM test allows you to determine if the program stored in the EPROM chip is intact.

1. In the Diagnostics menu, select the ‘‘EPROM TEST’’ and accept it by pressing the JustGo^TM/ ENTER key. The EPROM TEST

will perform automatically.

• The display will show ‘‘EPROM IS OK’’ if the EPROM is intact and it will display a “CHECKSUM” code (for Bodyguard^®

internal use only).

• The display will show ‘‘EPROM IS NOT OK’’. This means the EPROM might be damaged.

Keypad Test

The keypad test allows you to verify that each key is responding when pressed.

1. Press each key one at a time and verify the conﬁrmed response on the screen. Example, pressing the Elevation INCREASE

key will cause the screen to display “ELEVATION INCREASE” indicating that the key press was recognized.

2. Press the CLEAR/STOP and JustGo^TM/ENTER keys simultaneously to terminate the keypad test.

Display Test

The display test allows you to verify that each display light is properly working. If you notice that one or more areas on the

screen do not light up during an exercise, you should perform this test.

1. In the Diagnostics menu, select the “DISPLAY TEST” and accept it by pressing the JustGo^TM/ ENTER key.

2. Now the display will illuminate a certain way. To proceed to the next display patterns, press any key.

Sound Test

The sound test will cause the sound to sound.

1. In the Diagnostics menu, select the “SOUND TEST” and accept it by pressing the JustGo^TM/ENTER key.

Listen for a series of “beeps”. The sound test will stop automatically when you press the CLEAR/STOP key.

Heart Rate Test

The heart rate test allows you to determine if the heart rate system (chest strap or hand grip) is working properly and that

the computer is displaying your heart rate signal during a program.

1. In the Diagnostics menu, select the “HEART RATE TEST” and accept it by pressing the JustGo^TM/ ENTER key.

2. The top left display will show the signal received from the chest strap and the bottom window will show the hand grip

signal. Attach your heart rate chest strap. You do not need to step on the treadmill for this test, but simply stand near

the computer. Within a few seconds, your actual heart rate signal will be displayed on the screen. Do the same for the

hand grip system; put your hands on the two metal plates and wait for 10 to 15 seconds.

3. Press the CLEAR/STOP key to terminate the test.

Download from Www.Somanuals.com. All Manuals Search And Download.

Belt Alignment

Should you need to adjust the tracking of the running belt, you must make all adjustments during the BELT ALIGNMENT

procedure. To determine if the belt is not aligned along the center of the deck, measure the visible deck surface on both left

and right sides of the belt. If they are nearly equal, do not adjust the belt. If one side of the belt is closer to the foot rests

than the other side, then you will need to adjust the belt to track to the opposite side.

1. You will need a 7/16” (12 mm) deep socket

wrench to turn the bolts located inside the

rear roller end caps.

2. In the Diagnostics menu, select the “BELT

ALIGNMENT” and accept it by pressing the

JustGo™/ENTER key.

3. To continue the belt alignment procedure,

press the JustGo™/ENTER key.

4. To cancel the belt alignment procedure,

press the CLEAR/STOP key.

WARNING – Do not stand on the belt during

this procedure. Keep loose clothing and long

hair away from the belt and rollers when

performing belt alignment.

To verify the belt alignment, check visual gap (A) between

belt ends and foot rests (B). Belt alignment bolts (D) are

visible through hole in rear roller caps (C).

5. Allow the belt to reach 2.0 mph or 3.2

km/h (speed will be displayed on the

computer screen). Looking from the rear

of the treadmill, notice the gap between

left and right sides of the belt and the foot rests.

ﬁgure 9

If the running belt is tracking to the left of the deck surface:

•

turn the left bolt in a clockwise direction to allow the belt to track to the right and ultimately in the center, or;

turn the right bolt in a counter-clockwise direction to allow the belt to track to the right and ultimately in the

center.

If the running belt is tracking to the right of the deck surface:

•

turn the left bolt in a counter-clockwise direction to allow the belt to track to the left and ultimately in the center, or;

turn the right bolt in a clockwise direction to allow the belt to track to the left and ultimately in the center.

NOTE – During any belt alignment procedure, do not turn each bolt by more than 1 to 1-1/2 clockwise revolutions.

Exceeding this may cause a high amount of tension on the running belt and result in premature wear of the belt and

rollers. It is best to adjust only one alignment bolt, since this will prevent the belt from excessive stretching resulting from

adjustment of both alignment bolts.

6. To verify that the belt is properly aligned, slowly increase the speed to a maximum of 6.0 mph or 9.6 km/h, and let the

belt turn for at least one minute. Carefully observe that the belt does not track to the left or right side. If the belt

continues to track to one side, or you hear a rubbing noise, immediately press the CLEAR/STOP key to stop the belt. You

will need to verify the alignment again. Repeat steps 2 to 6.

Motor Check

Motor check should only be performed if your computer needs to be changed or repaired, or if you feel that the speed is

not working properly. The motor check procedure is automatic and does not require any tools.

1. In the Diagnostics menu, select the “MOTOR CHECK” and accept it by pressing the JustGo^TM/ENTER key.

2. Press the JustGo^TM/ENTER key to proceed.

3. Press the CLEAR/STOP key to terminate the test.

WARNING – Do not stand on the belt during this procedure.

Wait while the treadmill performs the motor check. That operation should take less than 30 seconds. Once completed, the

message “MOTOR OK” will be displayed.

WARNING – If the motor check procedure is canceled prematurely, do not use the treadmill. It is important to fully complete

the motor check procedure prior to using the treadmill.

Download from Www.Somanuals.com. All Manuals Search And Download.

Elevation Calibration

Elevation calibration should only be performed if your computer, your motor drive or your elevation motor need to be

changed or repaired, or if you feel that the elevation is not working properly. The elevation calibration procedure is

automatic and does not require any tools.

1. In the Diagnostics menu, select the “ELEVATION CALIBRATION” and accept it by pressing the JustGo^TM/ENTER key.

2. Press the JustGo^TM/ENTER key to proceed.

3. Press the CLEAR/STOP key to terminate the test.

WARNING – Do not stand on the belt during this procedure. The treadmill will elevate to a maximum of 15% incline.

Allow the treadmill to raise and lower automatically. The procedure will take approximately one minute to complete. If for

any reason you must stop the test, press the CLEAR/STOP key to terminate the test.

WARNING – If the elevation calibration procedure is canceled prematurely, do not use the treadmill. It is important to

fully complete elevation calibration procedure prior to using the treadmill.

Statistics

The statistics allow you to view different parameters related to the use of your treadmill such as time and distance.

1. In the Diagnostics menu, select the “STATISTICS” option and accept it by pressing the JustGo^TM/ENTER key.

•

The TOTAL TIME displayed indicates the amount of time the treadmill has been used during all exercise programs.

The TOTAL DISTANCE displayed indicates the total distance traveled with the treadmill during all exercise programs.

2. Press the CLEAR/STOP key to terminate the test.

Error Log

The error log allows you to see the number of times that an error has happened.

1. In the Diagnostics menu, select the "ERROR LOG" and accept it by pressing the JustGo^TM/ENTER key.

2. Using the SPEED INCREASE key, you will see all the speed errors and the number of times that they occurred in the left

top window.

3. Continue to press the SPEED DECREASE key to see the MOTOR DRIVE ERRORS. You will also see the number of errors that

happened in the left top window. If that number is 0, then there won't be any additionnal information displayed. If it is

different than 0, and to see the details of the errors, simply press the JustGo^TM/ENTER key.

4. In that submenu there will be two numbers shown. In the top left window, the rank of when that particular error

happened in time with respect to the other errors willl appear. Just under that rank, the error code of that error will

appear. For example, if the number 1 appears and the number 8 appears under, it means that ﬁrst error logged was an

error 8. To see the folllowing errors that happened in time after that ﬁrst one, simply press the SPEED DECREASE key. This

menu is useful for servicing and gives in depth information of what happened in the motor control board. To exit this

submenu, simply press the CLEAR/STOP key.

5. If you want to reset this error log, use the SPEED INCREASE OR INCREASE key to get to the item "RESET OF THE ERRORS".

NOTE - The table of errors can be viewed at the end of this document.

Download from Www.Somanuals.com. All Manuals Search And Download.

Current Test

The current test allows you to see the voltage and amperage in the motor.

1. In the Diagnostics menu, select “CURRENT TEST”. The motor will start and will reach 2.0 mph (or 3.2 km/h).

2. Press the JustGo^TM/ENTER key to proceed.

3. Walk on the treadmill for a couple of minutes and the value of the current and voltage at the motor will appear on the

central information window.

4. Vary the speed to ensure that you get good readings for different speeds.

5. Press the CLEAR/STOP key to terminate the test.

NOTE – During this test, the amperage and the tension will be shown on the central information window in the following

format: 3.1 A, 20V.

Here 3.1 A stands for 3.1 Amps and 20 V stands for 20 Volts DC.

The value of the amperage must never exceed 10 amps. If you exceed that value, it means the belt/deck combination

needs maintenance.

Speed Sensor Test

The speed sensor test allows you to see whether your speed sensor circuit is functional or not.

1. In the Diagnostics menu, select the “SPEED SENSOR TEST” and accept it by pressing the JustGo^TM/ENTER key.

2. Press the JustGo^TM/ENTER key to proceed and step off the machine. Allow the belt to reach 2.0 mph or 3.2 km/h.

3. A message will be displayed if the circuit is “GOOD” or “BAD” on the central information window:

• Check if your speed sensor is connected.

• Check if your optical disc is clean and that there is no dirt blocking the speed sensor.

4. Press the CLEAR/STOP key to terminate the test.

Maintenance

The maintenance menu allows you to see the average value of the current drawn by the motor. It also allows you to reset

this counter.

A ﬁrst threshold has been set to make sure that the normal high limit of current drawn by the motor will not be exceeded.

When that level is reached, the user will get the message DECK MAINTENANCE IS REQUIRED and a diamond sign will be

displayed on the main screen. The message and sign will be displayed between each new exercise. After the maintenance

has been done and reset in the diagnostics menu, the notice will go away until there is a new rise of current.

If the maintenance is not done on the deck surface when required, a second threshold will trigger not too high above the

ﬁrst one. Another notice with a square sign on the main display will come up. At that point the machine will not start again

until the deck maintenance is done and the maintenance has been reset in the diagnostics menu.

1. In Diagnostics menu, select “MAINTENANCE” and accept it by pressing the JustGo^TM/ENTER key. There are two sub

menu items: AVERAGE and RESET. Scroll between them with the INCREASE/DECREASE key and press the JustGo^TM/ENTER

key to accept your choice.

2. If you want to see the average current drawn by the motor simply go into the AVERAGE menu that will display the

average current in the motor from the last time it has been reset. To get out of that menu simply press CLEAR/STOP key.

3. If you have done the maintenance, you need to reset the maintenance counter by accessing the RESET MAINTENANCE

menu and enter that menu and conﬁrm that it has been done. You will then get a message that the “MAINTENANCE

COUNTER HAS BEEN RESET”.

4. Press the CLEAR/STOP key to terminate the test.

Level of alerts

Amperage

Diamond sign

Square sign

10 amps

11 amps

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance Information

nce Information

General Care

Your T700 have been designed and built to give you trouble free use. For maximum safety however, you should periodically

check your unit for signs of wear.

Here’s a quick check list followed by reference Table 3:

• After each workout, you should wipe down your T700 using a mild, non-abrasive liquid cleanser applied on a soft

cotton cloth. Do not spray cleansers directly on the unit or use an excessively damp cloth. Do not clean the unit with the

power ON, be sure that it is OFF.

• Be sure that the treadmill is on a level surface and that it is not rocking. Excessive rocking may cause the running belt to

track to one side of the deck resulting in accelerated wear of the running belt.

• Keep liquids including excessive sweat away from the computer console.

• The running belt and deck surface should be kept clean. Dirt and other debris can cause slipping when exercising.

• Check that each handle bar is secure on the frame.

• Do not put any lubricating product other than the Bodyguard^®lubricant.

• Place a carpet or rubber mat under the treadmill to avoid any build up of debris from your exercise shoes. Under

extreme conditions, some debris may collect on the ﬂoor just behind the rear roller. It is also recommended to periodically

remove any dust that may have accumulated under the treadmill. Excessive amounts of dust may enter into the motor

assembly and cause the motor to overheat.

• It is very important to periodically remove any dust that may have accumulated under the motor cover. Use compressed

air to blow out the accumulated dust in the motor and board area.

WARNING – To prevent electrical shock or risk of ﬁre, always turn the power OFF and disconnect the power cord whenever

you are inspecting and repairing your T700.

Download from Www.Somanuals.com. All Manuals Search And Download.

ﬁgure 10

Belt and Running Deck

Running Belt

The running belt supplied with each treadmill is of the highest

quality, offering superior traction and low noise under extreme

conditions. It is therefore important to maintain each running

belt periodically by observing that no cuts have appeared over

time, and that the running belt has not shifted to one side of

the deck surface. If the running belt constantly tracks (or moves)

to one side of the deck, you must adjust the alignment bolts

placed at the rear of the running belt.

See Belt Alignment for complete procedure.

ﬁgure 11

Motor in treadmill 240 VLT

Deck Surface

The running deck needs to remain free of any loose items that

may become trapped between the running belt and the rollers.

Avoid dropping liquids on the deck as this may cause gum up

problem on the belt.

Under extreme conditions resulting in heavy wear and tear on

the deck surface, it may be necessary to remove the deck and

turn it over, or turn it back-to-front to expose a fresh surface.

The deck is especially designed to offer four reversible sides for a

longer life use of the deck.

Please contact your Bodyguard^®Dealer for servicing the deck.

Make certain to have the power off before doing any

maintenance.

Motor in treadmill 120 VLT

1 - Breaker

2 - ON/OFF switch

Drive motor with connection wires.

1 - Speed sensor cable

2 - Computer power cable

3 - Elevation sensor cable

4 - Elevation motor cable

5 - Power AC cable

6 - Motor cable

Lubricant Application

1. Clean the deck surface and the inside part of the belt with a dry piece of fabric.

Clean the belt ﬁrst by using a long piece of fabric across the belt and start the

belt so it makes two co mplete turns. Then, release the tension on the rear roller

to be able to clean the deck surface of any debris or remaining wax.

2. Open the lubricant supplied by your dealer. Place the lubricant tube in the middle

of the belt at about 15 inches from the hood cover. Step on the treadmill and

step down with your feet where the lubricant tube is located under the belt to

make sure that most of the lubricant is now spread evenly on the deck surface.

DO NOT START THE TREADMILL YET.

3. Remove the LUBE TUBE from under the belt and put the tension back again on

the rear roller. Stand where you applied the lubricant and press JustGo^TM/ENTER

key to start the belt turning at 0.5 mph (or 0.8 km/h). Let the belt bring you a the

back of the treadmill and come back where you were standing. Do this twice so

the lubricant will be present on the total surface of the deck. Start the treadmill

and make sure the belt alignment is correct. Refer to the owner’s manual if any

problem occurs.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Troubleshooting Check List

If you experience a problem during the normal operation of the T700, use the following troubleshooting table below. If

you are unfamiliar or uncertain with basic diagnostic maintenance procedures, contact your Authorized Bodyguard^®

Dealer for diagnostics or repair of your T700.

Table 3

PROBLEM

POSSIBLE CAUSE/SOLUTION

• Computer will not light

up when power

is turned ON.

• Unit is not plugged in. – Plug unit in.

• Power cord. – Check that power cord is functional; replace if necessary.

• Circuit breaker. – Reset the breaker.

• Damaged motor circuit board. – Contact your Bodyguard^®Dealer.

• The belt is over tensioned. – Perform Belt Alignment.

• The wires are not connected. – Remove the cover and connect the wires properly.

• Magnetic key is not in place. – Insert the magnetic key.

• Belt doesn’t turn.

• Elevation does not

respond properly.

• It is not calibrated. – Perform Elevation Calibration.

• The wire is not connected on the motor circuit board. –

Connect the elevation wire to the circuit board.

• Motor drive does not

respond properly.

• It is not calibrated. – Perform Motor Check.

• The wire is not connected on the motor circuit board. –

Motor wiring harness needs to be connected to the lower board.

• Motor turns backwards.

• The wires are reversed on the circuit drive. –

Contact your Bodyguard^®Dealer.

• Keypad may be damaged by liquid penetrating through the seal. –

Contact your Bodyguard^®Dealer.

• Computer key(s) not

responding to touch,

or sticking.

• Excessive amount of cleaning solution used. –

Use mild cleanser on damp cloth only when cleaning console and unit.

• Poly V-belt slipping. – Contact your Bodyguard^®Dealer.

• Squeaking noise from

the motor.

• Motor brush noise excessive. – Contact your Bodyguard^®Dealer.

• Uneven ﬂoor. – Move the treadmill to an even ﬂoor.

• Belt tracks left

and right.

• Rear roller not adjusted for sloped ﬂoor. –

The rear roller needs to be adjusted. Perform Belt Alignment.

• The drive motor is not calibrated. – Perform Motor Check.

• Speed is not constant or

seems too fast or slow.

• The tension on the motor drive is too excessive. –

Remove tension on the running belt. Perform Belt Alignment.

• Elevation is not calibrated. – Perform Elevation Calibration.

• Can’t get out at the end

of a program.

• Error log

• See table 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Error Codes

Table 4

PROBLEM

CAUSE / SOLUTION

• Acceleration is too quick in the acceleration or reached speed phase.

• Error 1

• Possible causes: Motor drive defective or user pushing on the running belt for too long.

• Running belt not following the speed required in the reached speed phase.

• Possible causes: Deck too sticky. Walk on deck for 15 minutes at 4 mph.

• Motor drive board can be defective.

• Error 2

• Check speed sensor or optical disk.

• Acceleration is too fast during acceleration phase.

• Possible cause: Defective drive board.

• Error 11

• Error 12

• Acceleration is too slow during acceleration phase.

• Possible causes: Deck too sticky.

• Walk on deck for 15 minutes at 4 mph.

• Speed sensor problem.

• In a deceleration phase, the speed slows down too fast.

• Possible cause: Drive board defective.

• Error 21

• Error 22

• Error 23

• In a deceleration mode, the speed slows down too slowly.

• Possible cause: Drive board defective, speed sensor problem.

• There is an abnormal acceleration during the deceleration phase.

• Motor drive board is defective.

• Acceleration is too quick under 2 mph.

• Possible causes: Motor drive defective or user pushing on the running belt for too long.

• Elevation motor values from potentiometer are out of range.

• Possible causes: Elevation motor is defective or uncalibrated.

• Perform an elevation calibration in the diagnostics menu.

• Motor drive board can be defective.

• Error 31

• Elevation Motor not functionnal.

• Elevation Motor not connected.

•Elevation

Motor

Error

• A problem occurred on the motor control board. Contact your Bodyguard^®Dealer to give this

information. This will help ﬁnding the cause.

• Motor drive

error

Download from Www.Somanuals.com. All Manuals Search And Download.

Thank You for Purchasing a Bodyguard^®T700

Bodyguard^®Fitness is dedicated to designing and manufacturing the ﬁnest ﬁtness equipment available today.

This manual outlines information on warranty, assembly, operation of the unit, safety and basic maintenance checks for the

Bodyguard^®T700 treadmill.

When you require service for your T700, always present the unit product model, serial number and date of purchase to the

Bodyguard^®Dealer. The product model and serial numbers are located at the front of the machine. Now is a good time to write

the product model and serial numbers and related information in the space provided.

Product Name

Model Number

Serial Number

Date Purchased

Dealer Store Name

Dealer Phone Number

Please ﬁll out the warranty registration card and return it to Bodyguard^®Fitness within 30 days of date of purchase for

registration of your T700 warranty. Your returned warranty registration card is important in helping us keep you up-to-date with

all the latest T700 product additions. Also, the warranty card is used to establish the actual sale date.

NOTE – The warranty card is use to establish the beginning of the warranty of your treadmill. If you omit to send your warranty

card to Bodyguard^®Fitness, we will use the dealer purchase date to honor the warranty time.

You can also register on-line at www.bodyguardﬁtness.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety requirements

North America

The T700 treadmill has been tested and approved to meet all ETL requirements concerning electrical and mechanical

safety. In addition, the T700 treadmill conforms to UL 1647 and CAN/CSA-E335-1/2E.

International

The equipment listed in this manual has been tested to meet the Low Voltage Directive 73/23/EEC concerning the electrical

and mechanical safety.

Interference limits requirements

North America

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Canada

This equipment has been tested and found to comply with the limits for a Class B device, pursuant the standard NMB003.

International

This equipment has been tested to comply with the Electromagnetic Interference Compatibility directive 89/336/EEC

required by the International Electrical Committee.

Download from Www.Somanuals.com. All Manuals Search And Download.

MADE IN CANADA

Download from Www.Somanuals.com. All Manuals Search And Download.

Bolens Log Splitter 244 642 000 User Manual
Bosch Power Tools Grinder 1800 User Manual
Briggs Stratton Lawn Mower IS3100Z User Manual
Brinkmann Fishing Equipment 140 1516 0 User Manual
Brother All in One Printer 8080DN User Manual
Bushnell Battery Charger PP2010 User Manual
Carrier Refrigerator 23 XL User Manual
Casio Computer Hardware DT X11 Series User Manual
Chief Manufacturing Video Gaming Accessories PACPC1 User Manual
Chromalox Switch KDS 1 User Manual