P12
y
BATTERY CHARGER REMOTE
Scan for
additional
product
information
Instructions
Register your P12 Remote Display at bluesea.com/warranty
PN 7520 / PN 1521
Blue Sea Systems stands behind its products for as long as you own them. Blue Sea
Systems will replace or issue a credit for any of its products found to be defective in
materials or manufacture. P12 Battery Chargers and P12 Remote Displays are warranted
for a period of five years from the date of first purchase. No compensation will be allowed
for products not returned to Blue Sea Systems for analysis, nor will compensation be made
for labor required to replace any defective product. Please contact Customer Service for an
RMA number prior to shipping any product back to Blue Sea Systems. Blue Sea Systems
cannot accept liability for damage due to the use of the P12 Battery Charger.
Indicates battery charger stage, alerts, and controls basic
battery charger functions
LED Indicators
• Charging: Quick check for green light confirms charging
• Charge Stage: Displays charging stage including PreFloat for each battery
• Equalize: Indicates when the charger is in equalization mode
• Fan Mode: Indicates charger’s internal fan mode
• Charge Output: Displays the percentage of output current for each battery.
Will also indicate maximum output setting when maximum output is adjusted
to accommodate for AC source limitations.
• Alert: Provides warning and alert status for quick diagnostics
Four Control Buttons
• Fan: User adjustable settings (OFF, LOW, or HIGH)
• Dim/ Alarm: Provides adjustment to brightness of LEDs on display as well
as Silence function for alarms.
“Date of first purchase” means:
1. The date on which the product was purchased by the first retail customer
2. The date on which the first retail customer purchases a vessel on which the product
was installed
Blue Sea Systems will (at its sole discretion) repair or replace any product which is:
1. Proven to be defective in materials or workmanship
2. Returned to Blue Sea Systems (or its agent) during the warranty period in accordance
with this warranty
The replacement battery charger may be new or refurbished in as-new condition. Such
repair or replacement will be the sole remedy by Blue Sea Systems under this warranty.
Any repaired or replacement product will be warranted in accordance with this warranty for
the unexpired balance of the warranty period on the original product.
• Output: User adjustable charger output when AC source limitations exist
that require lowering the AC current draw.
• Standby: Places P12 Battery Charger into standby mode
GUARANTEE: Blue Sea Systems stands behind its products for as long
For customer service, call 800-222-7617.
Blue Sea Systems Inc.
425 Sequoia Drive
p 360.738.8230
f 360.734.4195
Bellingham, WA 98226 USA
980016790 Rev.001
Specifications
Included Components
1.Mounting Screws: (4) #6 x 1" pan-head sheet metal screws (#2 Phillips screwdriver)
2. Cover
3. Remote Assembly
4. Mounting Gasket
Minimum Operating Temperature
Maximum Operating Temperature
Minimum Storage Temperature
Maximum Storage Temperature
−20°C (−4°F)
60°C (140°F)
−30°C (−22°F)
70°C (158°F)
5. 25 ft (7.6 m) Cat5e Cable
Electrical Specification:
6. Dielectric Grease: Blue Sea Systems recommends using a high quality dielectric grease
for remote control connection. View the MSDS for the Dielectric
Grease at bluesea.com/P12
On State Operating Current
<300mA sourced from charger
Communications:
Protocol
Proprietary
Maximum Cable Length
Cable
150 ft (45.7 m)
Cat5e (Standard US)
Mounting Hole Cutout
1-1/4" (31.75 mm)
3.01" (76.56 mm)
4.15" (105.46 mm)
.95" (24.01 mm)
#6 Screws
Dimensions
Height:
Width:
Depth:
1
Mounting Hardware Included
Regulatory
Surface Mount Gasket creates an IP67 waterproof seal on unit face--temporary
immersion for 30 minutes.
4
3
2
6
5
1 of 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Alerts and Diagnostics
5. Thermal Regulaton:
SOLID ON (Yellow): The charger temp output limit LED indicator will blink to notify the user that the charger is limiting its output to protect itself from eventual overheating. The
most common correction for this state is to increase the fan speed to High. If the fan speed is already set to High check for blockage around the fan vent that can be removed.
If the condition persists, it is advisable to reposition the battery charger in a cooler, more ventilated location. See P12 Battery Charger User Manual page 20 for more details.
6. Internal Temperature Sensor:
BLINKING (Red): Indicates a problem with the thermistor temperature sense internal to the charger. If that is the case, the charger will immediately go into standby mode.
This form of temperature alert can not be corrected by the user. Contact Blue Sea Systems for further information regarding internal temperature sensor alerts.
7. Battery Temperature Sensor:
BLINKING (Red): Indicates the battery temperature is out of range. The charger will not charge a battery exceeding temp limits and will therefore go into standby
mode immediately. The remote will signal its alarm. If at any point the temperature sensor records a temperature beyond the defined temperature limits, the battery
charger will display the Battery Temperature Alert Screen. In this situation all battery charging will stop until the proper battery temperature is restored. Normal operation
will not commence unless two degrees within the temperature parameters. See P12 Battery Charger User Manual page 20 for more details.
8. Fan:
BLINKING (Red): Indicates the chargers’ internal fan is not working properly. See P12 Battery Charger User Manual page 20 for more details.
9. DC Fuse:
BLINKING (Red): Indicates the chargers’ internal DC fuse is blown. The P12 Battery Charger has two internal DC fuses that are not accessible by the user. Disconnect AC
power and all battery connections. The battery charger will require servicing by Blue Sea Systems. No attempts should be made to replace the fuses by the user. Contact Blue
Sea Systems for further instructions regarding DC fuse replacement.
10. AC Input Voltage Too High or Low:
BLINKING (Red): Indicates charger AC power is out of range. See P12 Battery Charger User Manual page 21 for more details.
11. DC Reverse Polarity or Short Circuit:
BLINKING (Red): Indicates a reverse polarity or short circuit condition is present on the DC output. The remote will signal its alarm. See P12 Battery Charger User Manual
page 20 for more details.
12. Hardware Failure, DC Output Voltage Too High, Equalization Overload: ALL ALERT LEDs BLINKING (Red): Indicates fault state.
Go to the P12 Battery Charger to see the pop-up screen explaining the reason.
Buttons
13. Fan Mode:
Press to scroll through fan mode selections OFF, LOW or HIGH.
See P12 Battery Charger User Manual for more details.
14. Dim /Alarm:
- Normal operation: Press to Dim LED brightness.
- Fault Condition: Press once to silence Alarm buzzer.
15. Output:
Limits the charger’s output to a certain percentage of its absolute maximum. Press the output button once to show the current output setting on Charge Output LEDs. Press
again to scroll through settings. The setting is shown via a row of solid LEDs correlating to the percentage. The user can set the output from 100% down to 25%.
16. Standby:
Puts the charger in Standby mode. If the charger is in charging mode, press once to go to Standby. If in Standby, press once to start charging again.
A blinking charging LED indicates the charger is transitioning from Standby to Charging.
See P12 Battery Charger User Manual for more details.
3 of 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Connection
The P12 Battery Charger Remote uses one Cat5e cable for communication and power.
P12 Battery
Charger Remote
P12 Battery Charger
RJ45 Port
Dimensioned Drawing
0.57"
(14.36mm)
4.15"
(105.46mm)
2.52"
(63.88mm)
3.01"
(76.56mm)
2.90"
(73.70mm)
0.38"
(9.65mm)
Mounting Hole Cutout
Ø1-1/4"
(31.75mm)
Clearance holes
for #6 screws
1.50"
(38.10mm)
Blue Sea Systems Inc.
425 Sequoia Drive
Bellingham, WA 98226 USA
p 360.738.8230
f 360.734.4195
3.69"
(93.66mm)
980016790 Rev.001
4 of 4
Download from Www.Somanuals.com. All Manuals Search And Download.
|