Blomberg Dishwasher DWS 54100 FBI User Manual

Dishwasher

Installation Manual

FOR MODELS (ADA Height)

DWS 54100 SS

DWS 54100 FBI

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

To prevent accidents, which could cause serious injury or death, as well as

machine damage read these instructions before installation and / or use.

1. IMPORTANT SAFETY INSTRUCTIONS

1.1 INSPECT THE DISHWASHER

1.2 HOW TO CONTACT US :

2. TOOLS WHICH MAY BE NEEDED

3. MATERIALS WHICH MAY BE NEEDED

4. MATERIALS SUPPLIED

4.1 PARTS SUPPLIED

4.2 MANUAL BAG

4.3 DISHWASHER PARTS BAG 1

4.4 DISHWASHER PARTS BAG 2

4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER

5. DISHWASHER SPECIFICATIONS

5.1 TECHNICAL FEATURES

6. ENCLOSURE PREPARATION

6.1 ELECTRICAL PREPARATION

6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS

6.3 ADJUSTING HEIGHT

6.4 PREPARING THE WATER CONNECTION (A)

6.5 DRAIN PREPARATION

6.7 STEAM PROTECTION FOIL

7. PLACEMENT OF DISHWASHER INTO THE OPENING

7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS

7.2 ELECTRICAL CONNECTION

7.3 READJUSTING FOOT LEVELS

7.4 ADJUSTING THE MOVABLE TOE KICK

7.5 INSTALLING THE OUTER DOOR

(DWS 54100 FBI)

8. INSTALLER CHECKLIST

9. FINAL INSTRUCTIONS

10. SELF HELP HINTS:

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

WARNING

Please read this installation manual and

particularly the safety instructions completely

and carefully. They will save you time

and effort and help to ensure optimum

dishwasher performance.

When installing the dishwasher, follow

basic precautions, including the

following:

• The dishwasher installation must be

performed in accordance with this

installation manual. If you did not receive

an installation manual, order it by

calling 1-800-459-9848 or you may also

download it from our web site at

www.blombergappliances.com

• The dishwasher could only be converted

from cord-connected to permanently

connected by an authorized service

representative. (If needed contact your

dealer to schedule an authorized service

agent for conversion with an appropriate

conversion kit)

Be sure to observe all listed warnings and

cautions. Look particularly for the icons with

exclamation marks inside. The information

icon also will provide important references.

WARNING

CAUTION

Notice

WARNING:

Indicates a potentially hazardous situation

which, if not avoided, could result in death or

serious injury.

• Installation and repair should be

performed by a qualiﬁed installer.

Work by unqualiﬁed persons could be

dangerous and may void the warranty.

CAUTION:

Indicates a potentially hazardous situation

which, if not avoided, may result in injury.

It may also be used to alert against unsafe

practices.

Notice :

Installation should be installed by an

insured licensed plumber, contractor or

trained installer. Installation performed

by persons other than this could result in

improper installation and property damage.

• Do not operate the appliance if damaged,

malfunctioning, partially disassembled or

if it has missing or broken parts.

Notice:

Indicates a potentially hazardous situation

which, if not avoided, may result in damage

to the dishwasher, the table-ware, the

equipment or the environment.

1. IMPORTANT SAFETY

• Also follow the safety instructions of the

user manual.

INSTRUCTIONS

In addition to these instructions, the

dishwasher shall be installed:

• To reduce the risk of electric shock, ﬁre,

or injury to persons, the installer must

ensure that the dishwasher is completely

enclosed at the time of installation.

• Only connect the dishwasher to the

power supply when all installation and

plumbing work is complete.

• If the dishwasher is installed in a location

that experiences freezing temperatures

(e.g. in a vacation home, cabin, etc.),

you must drain all the water from the

dishwasher’s interior. Water system

ruptures that occur as a result of freezing

are not covered by warranty.

• In accordance with all local codes or, in

absence of a local code,

• In the United States, with the National

Electric Code,

• In Canada, with the Canadian Electric

Code C22.1-latest edition/Provincial and

Municipal codes and/or local codes.

Notice :

Read these installation instructions

completely before installing and follow them

carefully. Save these installation instructions

and pass them on to any future user.

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

• Dishwasher must be secured to adjacent

cabinetry using the brackets provided.

Failure to do this may cause damage to

property or bodily injury.

• Replacement - If the dishwasher is

replacing another dishwasher, check

the existing dishwasher connections for

compatibility with the new dishwasher,

and replace parts as necessary.

• Connect to a properly rated, protected

and sized power supply circuit to avoid

electrical overload. The dishwasher is

designed for an electrical supply of 120 V

(volts), 60 Hz (hertz), AC, connected to a

dishwasher-dedicated, properly grounded

electrical circuit with a fuse or breakers

rated for 15 amperes. Electrical supply

conductors shall be a minimum of # 16

AWG copper wire rated at 75 °C (167

°F) or higher. These requirements must

be met to prevent injury and machine

damage. Consult a qualiﬁed electrician if

in doubt.

• Do not use any extension cord or

portable outlet device to connect the

dishwasher to a power supply.

• Ensure that any plastic wrappings, bags,

small pieces etc. are disposed of safely

and kept out of the reach of children.

Danger of suffocation!

1.1 INSPECT THE DISHWASHER

After unpacking the dishwasher and prior

to installation, thoroughly inspect the

dishwasher for possible freight or cosmetic

damage. Report any damage immediately.

Notice :

• Cosmetic defects must be reported within

10 days of installation.

• Do not discard any bags or items that

come with the original package until

after the entire installation has been

completed.

1.2 HOW TO CONTACT US :

You may either call our Toll Free Number at

1-800-459-9848 or contact us via the web

site at

www.blombergappliances.com

or Contact the Blomberg Distributor for

your State or Province as listed on the

Distributor Contact List provided.

• Remove the door to the washing

compartment when removing an old

dishwasher from service or discarding it.

Ensure that the appliance presents no

danger to children while being stored for

disposal.

• Old appliances may contain materials

that can be recycled. Please contact

your local recycling authority about the

possibility of recycling these materials.

Notice :

• The dishwasher drain hose must be

installed with a drain loop at least 28”

(710mm) off the cabinet ﬂoor; otherwise

the dishwasher may not drain properly.

• This dishwasher is intended for

residential use only, and should not be

used in commercial establishments.

• New installation - If the dishwasher is a

new installation, most of the work must

be done before the dishwasher is moved

into place.

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

2. TOOLS WHICH MAY BE NEEDED

3. MATERIALS WHICH MAY BE NEEDED

(Additional materials may be required to comply with local codes)

Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided

dishwasher supply line.

UL listed conduit connector or strain relief.

Teﬂon tape or other pipe thread compound to seal plumbing connections.

Shut-off valve and fittings appropriate for hot water supply line (copper

tubing/compression fitting, or braided hose).

Silicone

Glue

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

4. MATERIALS SUPPLIED

4.1 PARTS SUPPLIED

Parts for your dishwasher will come in several plastic bags.

Check your parts bags shown to make sure you have all the

parts as listed to the left.

4.2 MANUAL BAG

The dishwasher comes with a manual bag containing:

•

User manual,

Installation manual and

Quick reference guide.

4.3 DISHWASHER PARTS BAG 1

This dishwasher bag comes with the following parts:

a. Side Trim Strips (Left)

b. Side Trim Strips (Right)

c. Adjusting Wrench

d. Screws Ø

/ ” x

/ ” (Ø 3.5mm x 14mm)

e. Mounting Bracket Left

f. Mounting Bracket Right

g. Spring Clamp

h. Screw Clamp

j. Rubber Connector

k. Toe Kick Bracket - Left

l. Toe Kick Bracket – Right

m. Edge Protector

n. Long Legs

o. Toe Kick (toe kick without slots)

p. Toe Kick

r. Toe Kick

s. Plastic Caps

t. Screws Ø

” x

/ ” (Ø 4mm x 6mm)

z. Steam Protection Foil

aa. 90° elbow with 3/8” N.P.T. male threads on one leg, and

sized to fit your water supply line (copper tubing/compression

fitting, or braided hose) on the other leg.

4.4 DISHWASHER PARTS BAG 2

In addition to the manual bag and the dishwasher parts bag

1 DW 55, (dishwasher models which can accept a wooden

kitchen door) also come with a door panel installation kit which

contains:

v. Screws Ø

y. Screws Ø

” x

” x 1

” (Ø 3.5mm x 14mm)

/ ” (Ø 4mm x 43mm)

4.5 PARTS ATTACHED TO THE REAR OF THE

DISHWASHER

a. Side Trim Strips (Left)

b. Side Trim Strips (Right)

o. Toe Kick (toe kick without slots)

p. Toe Kick

aa.

r. Toe Kick

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

5. DISHWASHER SPECIFICATIONS

5.1 TECHNICAL FEATURES

Load capacity

8 place settings

Permissible water

pressure

4.35 - 145 psi (0.3 - 10 bars)

120 V (volts), 12 A (amps),

60 Hz (hertz)

Electrical connection

Total power

1400 W (watts)

1240 W (watts)

Heater power

Notice :

Because we continually strive to improve our products, we may change our specifications

and design without prior notice. This device corresponds to the following directives:

UL 749 Household Dishwasher directive.

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

6. ENCLOSURE PREPARATION

6.1 ELECTRICAL PREPARATION

WARNING

The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a

dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated

for 15 amperes.

6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS

WARNING

Dishwasher must be secured to adjacent

cabinetry using the mounting brackets

provided. Failure to do this may cause

damage to property or bodily injury.

Place the two mounting brackets into the

top corners of the dishwasher.

Bend sides of mounting brackets (A) in

order to fix from sides (if necessary).

Notice :

•

For these model, DWS 54100 FBI

note that extra bending should be

done on the brackets as shown.

6.3 ADJUSTING HEIGHT

Measure the height of the

enclosure.

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

6.3.1 INSTALLING THE FOOT SUPPORTS

Supplied (4)

If the height of the enclosure is 33

” to

” (850mm - 870mm) use short supports

as shown in the figure.

If the height of the enclosure is above

Supplied (4)

” (870mm) use long supports as

shown in the figure.

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjust the front foot level with the adjusting

wrench to balance and raise the dishwasher to

the enclosure height.

Adjust the rear foot level with a screwdriver

to balance and raise the dishwasher to the

enclosure height.

Notice :

•

Make sure the dishwasher is plumb

and notice dishwasher can be placed

with a small clearance under the

counter top.

T20

•

Turning the screwdriver in the

direction of the black arrows will bring

the dishwasher back feet up.

Turning the screwdriver in the

direction of the white arrows will take

the dishwasher rear feet down.

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

6.4 PREPARING THE WATER CONNECTION (A)

Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder

connections must be made before the water line is connected to the dishwasher’s water

inlet valve. Water can also be supplied to the dishwasher by using a ﬂexible braided hose

line.

Check with your plumbing supply sources for the proper hose and 90° elbow and

necessary fittings for the water supply line. This material is not supplied, and must be

purchased separately.

WARNING

Installation should be performed by a qualified installer. Work by unqualified

persons could be dangerous and may void the warranty.

If the dishwasher is installed in a location that experiences freezing temperatures

(e.g. in a vacation home, cabin etc.), you must drain all the water from the

dishwasher’s interior. Water system ruptures that occur as a result of freezing are

not covered by warranty.

6.4.1 INSTALLING THE 90° ELBOW FITTING (B)

CAUTION

Do not over tighten the 90° elbow. Doing so

may damage the water inlet valve and cause a

water leak.

If the water supply line is to be copper tubing,

make certain that the elbow has a compression

fitting. Apply Teﬂon tape or other pipe sealant

when required. Orient the water supply connection

downwards as shown in the figure so the water line

can be easily pulled underneath or on the side of

the dishwasher.

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

6.5 DRAIN PREPARATION

The dishwasher drain hose may be connected to the drain plumbing in one of three ways

(Figure A, B, C).

Notice :

•

Either one of the above methods must be used or the dishwasher will not operate

properly.

•

A hose that attaches to a sink spray can burst if it is installed on the same water

line as the dishwasher. If your sink has one, it is recommended that the hose be

disconnected and the hole plugged.

The total length of the drain hose is 76

•

” (1950mm). If a hose extension is

required, a drainage hose of equal quality must be used.

The maximum length must not exceed 157 ½” (4000mm). Otherwise, the cleaning

process is negatively inﬂuenced.

6.5.1 UNDER THE SINK DRAIN

Install a Y-branch tail pipe. (Figure A)

Notice :

•

You must add a loop at least 28” (710mm) above the ﬂoor

of the cabinet and above the drain connection in the drain

hose to prevent waste water from not draining properly,

and causing either poor washing results or a bad odor.

6.5.2 INSTALLING AN AIR GAP

If the local ordinance requires an air gap (Figure B).

Notice :

•

Check with local ordinance for type of air gap required.

6.5.3 DISPOSAL

Remove the drain connection plug before attaching the drain

hose from the dishwasher.

Every disposal has a hook up for a dishwasher; consult your

disposer manual for correct connection. (Figure C)

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

6.7 STEAM PROTECTION FOIL

Steam will form inside the dishwasher during operation. At the end of the cycle, when the

dishwasher door is opened, it is required to use a steam protection foil to prevent any

steam from collecting on the underside of the counter top.

6.6.2 FITTING THE PROTECTION FOIL

Before applying the steam protection foil to the

underside of the countertop, clean the area with

a damp cloth (as shown in Figure A). Once the

area dries, apply the steam protection foil.

The steam protection

foil will be applied at the

location where the hot

steam escapes when you

first open the door (as

shown in Figure B).

CAUTION

Steam protection foil must be applied

where the steam escapes when door is

first opened. Failure to install the steam

protection foil during installation can

lead to damage to the cabinets and

countertop.

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

7. PLACEMENT OF DISHWASHER INTO THE OPENING

Now place the dishwasher into the opening and get ready to connect all hoses and electrical

connections.

CAUTION

Make sure all hoses

are pulled through the

side opening of the

cabinet, no hoses are

kinked and all slack is

taken out as shown in

the above figure.

7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL

CONNECTIONS

7.1.1 DRAIN HOSE CONNECTION

Connect the drain hose to the drain plumbing.

1. Use the supplied rubber connection hose and drain hose clamps to connect the dishwasher drain

hose to the plumbing drain connection.

2. Use the spring clamp to secure the rubber connection hose to the dishwasher drain hose. Use the

screw clamp to secure the rubber connection hose to the plumbing drain connection.

Note that the marks on the

rubber connection hose should

be on the drain hose side

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

7.1.2 WATER SUPPLY CONNECTION

Water supply may be connected to the dishwasher in one of

two ways:

• With metal braided hose.

• With copper tubing.

7.1.3 BRAIDED HOSE/COPPER TUBING

After connections are made turn on the water supply to check

for leaks.

CAUTION

•

Hot water supply line: Use minimum 3/8” O.D. copper tubing or metal braided dishwasher

supply line.

•

Temperatures required for soldering and sweating will damage the dishwasher’s water inlet

valve so if any such operation is needed, keep the heat source min. 7

from the dishwasher’s water inlet valve.

/ ” (200mm) away

•

There should not be any sharp bends in the water line that may restrict the water ﬂow.

Teﬂon tape or pipe tread compound must be used for sealing the connection. Before

connecting the copper water supply line to the dishwasher, ﬂush it with hot water to clear any

foreign material.

Notice :

After connections are made turn on the water supply to check for leaks.

7.2 ELECTRICAL CONNECTION

WARNING

•

Make sure the voltage and frequency listed on the data plate correspond with the

household electrical supply. This data must correspond to prevent injury and machine

damage. Consult a qualified electrician if in doubt.

•

Only connect the dishwasher to the mains when all installation and plumbing work is

complete.

Do not use any extension cord or portable outlet device to connect the dishwasher to

a power supply.

The power-supply receptacle for the appliance shall be installed in a cabinet or on a

wall adjacent to the undercounter space in which the appliance is to be installed.

The access hole of the supply cord to the installation compartment must be smooth

and rounded and it must be large enough for the attachment plug to pass through.

The longest dimension of the opening shall not be more than 1,5” (38 mm).If the

partition is metal, it needs to be covered with the edge protector (m).

Care must be taken when the appliance is installed or removed, to reduce the

likelihood of damage to the power-supply cord.

•

7.2.1 GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce

the risk of electric shock by providing a path of least resistance for electric current. This appliance is

equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes

and ordinances. This appliance must be connected to a grounded metal, permanent wiring system,

or an equipment-grounding conductor must be run with the circuit conductors and connected to the

equipment-grounding terminal or lead on the appliance.

WARNING

•

Improper connection of the equipment-grounding conductor can result in a risk of

electric shock. Check with a qualified electrician or service representative if you are

in doubt whether the appliance is properly grounded. Do not modify the plug provided

with the appliance, if it will not fit the outlet, have a proper outlet installed by a

qualified electrician.

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

7.3 READJUSTING FOOT LEVELS

Now that the dishwasher is in the cabinet you

must readjust the feet to bring the dishwasher up

to the required height and attach it underneath the

countertop.

1. Readjust the front foot levels with adjusting

wrench to balance the dishwasher and raise it up

under the countertop, make sure the unit is level.

2. Readjust the rear foot levels with a screwdriver

to balance the dishwasher and raise it to the

required height using the brackets supplied.

3. Attach the dishwasher underneath the

countertop with the four screws supplied (Ø

”

/ ” - Ø 3.5mm x 14mm). Make sure you do not

go through the top of the countertop or damage

granite.

Notice :

•

For model, DW 55100 FBI, note

that you should keep the total

height of the dishwasher at 32^1/4”

(819mm) max.

(3,5mm)

7.4 ADJUSTING THE MOVABLE TOE KICK

Now that you have successfully installed the dishwasher, you need to

attach the toe kick to the dishwasher. The two piece toe kick can be

adjusted to the height and depth needed for your kitchen. Be sure to

use the slotted toe kick in the front and the other behind it. They slide

into each other.

1. Insert the movable toe kick brackets into the channel (A).

2. Make sure that the plastic tab to the left of the “L” opening on the

dishwasher has not closed the channel you will push the bracket

through.

Notice :

Be sure to notice there is a left and a right bracket.

Adjust the toe kick brackets forward or backwards so that they will

align with the kitchen toe kick (B).

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

Lock the toe kick brackets as shown with the plastic tab in

the figure C by pushing the plastic tab on the dishwasher

into the teeth of the bracket (C).

3. Now attach the toe kick to the bracket with the two

(Ø

” x

” - Ø 4mm x 6mm) screws and the caps

provided as follows.

If the enclosure height is below 33

/ ” (840mm) use only

“o” labelled toe kick (toe kick without slots). Installation

should be done following the steps illustrated in the

Figures A, B and C respectively.

1. Bend tabs on toe kick (o) inwards (A).

2. Secure toe kick to brackets with screws (t) as shown in

the supply bags (B).

3. Attach caps (s) as shown in the supply bags (C).

If the enclosure height is above 33

/ ” (840mm) use “o”

and “p” labelled toe kicks together. Make sure the slotted

toe kick “p” is on the outside so you can adjust height of

the toe kick. Installation should be done following the steps

illustrated in the figures A, B and C respectively.

1. Align the toe kick (o) and (p) (A).

2. Secure toe kicks to brackets with screws (t) after

adjusting the height of the slotted toe kick (p) (B).

3. Attach caps (s) as shown in the supply bags (C).

If the enclosure height is above 34

/ ” (870mm) use “o”

and “r” labelled toe kicks together. Make sure the slotted

toe kick “r” is on the outside so you can adjust height of

the toe kick. Installation should be done following the steps

illustrated in the figures A, B and C respectively.

1. Align the toe kick (o) and (r) (A).

2. Secure toe kicks to brackets with screws (r) after

adjusting the height of the slotted toe kick (t) (B).

3. Attach caps (s) as shown in the supply bags (C).

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

7.5 INSTALLING THE OUTER DOOR

(DWS 54100 FBI)

Measure the height and width of the enclosure (Figure A)

and the toe kick. Determine how big the wooden door can

be. For example if the height is 33

” (860mm) and if the

toe kick is 3

/ ” (100mm) the door can not be taller than

/ ” (760mm).

1. Prepare the wooden door with the mounting brackets.

Height

: Height of the wooden door 28” (711mm)

: 17 ½” to 17 ¾” (442 mm - 448 mm)

: ¾ “ (19mm)

Width

Thickness

2. To take the plastic bracket out, remove the

screws on it. Screws will be used in 5th step

again. (Figure B).

3. Mark the wooden door as shown in the

drawing (Figure C).

”

155mm

(155mm)

Mid. Point

Max : 12,1 lb

(5,5 kg)

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Place the plastic mounting brackets over the marked

holes and the side tabs must be ﬂush with the edge of

the wooden door (Figure D).

5. Attach the two mounting brackets to the wooden door

with 4 screws (Ø

/ ” x

/ ” (Ø 3.5mm x 14mm) (Figure

(3,5mm)

A).

6. Mount the wooden door onto the dishwasher with

the plastic mounting brackets which you have attached

(Figure B).

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Open the door and remove the two caps and two

screws inside the door at position 1 and 3 (Figure C).

” x 1

8. Using the four screws Ø

” (Ø 4mm

x 43mm) provided, attach the wooden door to the

dishwasher at position 1 and 3 (Figure A).

^{" (4mm)}x4

9. Check the position of the wooden door and make

sure it is aligned properly (Figure B).

10. Tighten the screws in position 1 and 3 completely

after the final alignment (Figure C).

" (4mm)

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

11. Check whether the bottom of

the door hits the toe kick of the

kitchen cabinet (A).

11.1. If the door hits the toe kick

cut the necessary section out of

the toe kick (B).

11.2. Apply silicon or sealant

to the cut edge of the kitchen

cabinet toe kick or paint so it does

not absorb moisture.

ADJUSTING DOOR TENSION WITH CUSTOM WOODEN DOOR

(DWS 54100 FBI)

Check the door tension of the dishwasher:

If the door closes too quickly or if the door

falls open, the spring tension needs to be

adjusted.

The adjustment screws can be found on the

front of the dishwasher after you open the

door (see drawing).

Adjust the spring tension by turning

the screw to the right for more weight

and to the left for less weight (Figure

C).

0 kg

USA

Download from Www.Somanuals.com. All Manuals Search And Download.

Notice :

If you have a European kitchen or want to install a wooden toe kick to match your kitchen, please refer to

one of the two drawings given below. Follow the same instructions on the brackets as for the removable

toe kick.

Installation should be done following the steps illustrated in the figures A, B, C, D respectively.