Blodgett Convection Oven MARK V XCEL CONVECTION OVEN User Manual |
MARK V XCEL
CONVECTION OVEN
INSTALLATION -- OPERATION -- MAINTENANCE
BLODGETT OVEN COMPANY
44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone (800) 331-5842, (802) 860-3700 Fax: (802)864-0183
PN 36433 Rev C (2/05)
E 2003 --- G.S. Blodgett Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
THE REPUTATION YOU CAN COUNT ON
For over a century and a half, The Blodgett Oven Company has been building
ovens and nothing but ovens. We’ve set the industry’s quality standard for all
kinds of ovens for every foodservice operation regardless of size, application
or budget. In fact, no one offers more models, sizes, and oven applications
than Blodgett; gas and electric, full-size, half-size, countertop and deck, con-
vection, Cook’n Hold, Combi-Ovens and the industry’s highest quality Pizza
Oven line. For more information on the full line of Blodgett ovens contact your
Blodgett representative.
Download from Www.Somanuals.com. All Manuals Search And Download.
Model:
Your Service Agency’s Address:
Serial Number:
Your oven was installed by:
Your oven’s installation was checked by:
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction
Installation
Oven Description and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Delivery and Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
4
4
5
5
6
6
7
8
9
Oven Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sanitation Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leg Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Double Section Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oven Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Utility Connections --- Standards and Codes . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initial Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Solid State Manual Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Solid State Digital Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Solid State Digital Control with Humidaire . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CH-Pro3 (Solid State Programmable Digital Control) . . . . . . . . . . . . . . . . . . 18
Blodgett IQ2T Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
General Guidelines for Operating Personnel . . . . . . . . . . . . . . . . . . . . . . . . . 30
Maintenance
Cleaning and Preventative Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Oven Description and Specifications
Cooking in a convection oven differs from cooking
in a conventional deck or range oven since heated
air is constantly recirculated over the product by
a fan in an enclosed chamber. The moving air con-
tinually strips away the layer of cool air surround-
ing the product, quickly allowing the heat to pene-
trate. The result is a high quality product, cooked
at a lower temperature in a shorter amount of time.
Blodgett convection ovens represent the latest ad-
vancement in energy efficiency, reliability, and
ease of operation. Heat normally lost, is recircu-
lated within the cooking chamber before being
vented from the oven: resulting in substantial re-
ductions in energy consumption and enhanced
oven performance.
Air Flow Pattern for Mark V XCEL
Figure 1
ELECTRICAL SPECIFICATIONS (per section) -- MKV1XL/AA
Volts Phase Electrical Connection
KW
Hz
Amps
(minimum size)
L1
L2
L3
N
U.S. and Canadian installations
11.0
11.0
11.0
11.0
11.0
11.0
60
60
60
60
60
60
208
208
1
3
1
3
3
3
53
33
50
31
16
15
---
53
33
50
31
16
15
---
---
---
---
---
---
6 AWG
8 AWG
6 AWG
8 AWG
12 AWG
12 AWG
28
---
220-240
220-240
440
26
13
12
480
General Export installations
11.0
11.0
11.0
50
50
50
220-240
240/415
230/400
1
3
3
50
19
19
---
50
14
14
---
5
5
Size per local code
Size per local code
Size per local code
14
14
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Delivery and Location
DELIVERY AND INSPECTION
It is essential that an adequate air supply to the
oven be maintained to provide a sufficient flow of
combustion and ventilation air.
All Blodgett ovens are shipped in containers to
prevent damage. Upon delivery of your new oven:
D Inspect the shipping container for external dam-
age. Any evidence of damage should be noted
on the delivery receipt which must be signed by
the driver.
D Place the oven in an area that is free of drafts.
D Keep the oven area free and clear of all combus-
tibles such as paper, cardboard, and flammable
liquids and solvents.
D Do not place the oven on a curb base or seal to
a wall. This will restrict the flow of air and prevent
proper ventilation. Tripping of the blower mo-
tor’s thermal overload device is caused by an
excessive ambient temperature on the right
side of the oven. This condition must be cor-
rected to prevent permanent damage to the
oven.
D Uncrate the oven and check for internal dam-
age. Carriers will accept claims for concealed
damage if notified within fifteen days of delivery
and the shipping container is retained for in-
spection.
The Blodgett Oven Company cannot assume
responsibility for loss or damage suffered in
transit. The carrier assumed full responsibility
for delivery in good order when the shipment
was accepted. We are, however, prepared to
assist you if filing a claim is necessary.
Before making any utility connections to this oven,
check the rating plate to be sure the oven specifi-
cations are compatible with the electrical services
supplied for the oven.
1. Open the doors, the rating plate is located un-
der the top edge of the oven.
OVEN LOCATION
The well planned and proper placement of your
oven will result in long term operator convenience
and satisfactory performance.
The following clearances must be maintained be-
tween the oven and any combustible or non-com-
bustible construction.
D Oven body right side --- 0” (0 cm)
D Oven body left side --- 0” (0 cm)
D Oven body back --- 0” (0 cm)
D Oven body bottom --- 1/2” (1.2 cm)
The following clearances must be available for ser-
vicing.
D Oven body sides --- 12” (30 cm)
D Oven body back --- 12” (30 cm)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Oven Assembly
SANITATION BOLTS
These bolts are required by NSF to block any ex-
posed hole on the back of an oven. This includes:
1. Locate the 5/16” bolts that were shipped with
the oven.
2. Install the bolts as shown in Figure 2.
D any unit, single or stacked, without a back panel.
D any holes in stacked units not used for mount-
ing stacking brackets.
Double Stacked Units
Units without back panels
Figure 2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Oven Assembly
LEG ATTACHMENT
CASTER ASSEMBLY
1. Lay the oven on its back.
NOTE: Install the locking casters on the front of
the oven. Install the non-locking casters on
the back of the oven.
2. Align the threaded stud in each leg with the
nut located inside each bottom corner of the
oven frame. Turn the legs clockwise and tight-
en to the nearest full turn.
3. Align the two leg plate holes in each leg with
those in the oven bottom. Secure each leg us-
ing two 1/2” bolts.
Casters for Single and Double Stacked Ovens:
1. Attach the legs as described.
2. Pry the adjustable feet out of the legs
3. Insert one caster into each leg as shown.
Tighten the lock nuts to secure the casters.
NOTE: If using casters see CASTER AS-
SEMBLY before proceeding.
4. Tip the oven up on the legs.
5. Level the oven by screwing the adjustable leg
feet in or out as necessary.
Adjustable
Leg Foot
Caster Assembly
25” (64 cm) Legs Shown
Figure 4
Low Profile Casters for Double Stacked Ovens:
1. Align the three holes in each caster assembly
plate with those in the oven bottom. Secure
each caster using three 1/2” bolts.
6” (15 cm) Legs Shown
Figure 3
Figure 5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Oven Assembly
DOUBLE SECTION ASSEMBLY
1. Secure the short legs to the bottom sections
as described.
2. Attach lower flue box to lower oven.
3. Place the upper section in position on top of
the lower oven.
WARNING!!
When stacking ovens be sure to remove
the single oven flue boxes prior to attach-
ing upper and lower boxes and riser.
4. Attach the stacking brackets using the re-
maining 5/16” bolts shipped with the ovens.
5. Install flue riser and attach upper flue box to
upper oven.
OVEN LEVELING
After assembly, the oven should be leveled and
moved to the operating location.
1. The oven can be leveled by adjusting the feet
or casters located on the bottom of each leg.
Flue
Boxes
Flue Riser
Figure 6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Utility Connections --- Standards and Codes
THE INSTALLATION INSTRUCTIONS CON-
U.S. and Canadian installations
TAINED HEREIN ARE FOR THE USE OF QUALI-
FIED INSTALLATION AND SERVICE PERSONNEL
ONLY. INSTALLATION OR SERVICE BY OTHER
THAN QUALIFIED PERSONNEL MAY RESULT IN
DAMAGE TO THE OVEN AND/OR INJURY TO
THE OPERATOR.
All ovens, when installed, must be electrically
grounded in accordance with local codes, or in the
absence of local codes, with the National Electrical
Code, ANSI/NFPA 70---Latest Edition and/or Cana-
dian National Electric Code C22.2 as applicable.
The ventilation of this oven should be in accor-
dance with local codes. In the absence of local
codes, refer to the National ventilation code titled,
“Standard for the Installation of Equipment for the
Removal of Smoke and Grease Laden Vapors from
Commercial Cooking Equipment”, NFPA-96-Latest
Edition.
Qualified installation personnel are individuals, a
firm, a corporation, or a company which either in
person or through a representative are engaged
in, and responsible for:
D the installation of electrical wiring from the elec-
tric meter, main control box or service outlet to
the electric appliance.
Qualified installation personnel must be experi-
enced in such work, familiar with all precautions
required, and have complied with all requirements
of state or local authorities having jurisdiction.
General export installations
Installation must conform with Local and National
installation standards. Local installation codes
and/or requirements may vary. If you have any
questions regarding the proper installation and/or
operation of your Blodgett oven, please contact
your local distributor. If you do not have a local dis-
tributor, please call the Blodgett Oven Company at
0011-802-860-3700.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Electrical Connection
Wiring diagrams are located in the control
compartment and on the back of the oven.
4. Connect the supply wires to top of right con-
tactor in the control compartment at the lower
right corner of the oven.
5. Reinstall the bottom trim and control panel
covers.
The electric motor, indicator lights and related
switches are connected to the oven as follows:
1. Remove the bottom trim and control panel
covers. Slide the control panel forward.
2. Connect the supply conduit to the wire duct lo-
cated in the lower left hand corner on the back
of the oven.
NOTE: To prevent damage there is no power to
the heating elements when the blower is
not operating.
THE BLODGETT OVEN COMPANY CANNOT AS-
SUME RESPONSIBILITY FOR LOSS OR DAMAGE
SUFFERED AS A RESULT OF IMPROPERINSTAL-
LATION.
3. Run the supply wires through the duct to the
front of the oven.
Install incoming
power on this
contactor
Figure 7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Initial Startup
OVEN RESTRAINT
ADJUSTMENTS ASSOCIATED WITH INITIAL
INSTALLATION
If casters are used in conjunction with a power
supply cord for movable appliances, a fixed re-
straint should be provided.
Each oven, and its component parts, have been
thoroughly tested and inspected prior to ship-
ment. However, it is often necessary to further test
or adjust the oven as part of a normal and proper
installation. These adjustments are the responsi-
bility of the installer, or dealer. Since these adjust-
ments are not considered defects in material or
workmanship, they are not covered by the Original
Equipment Warranty. They include, but are not
limited to:
The restraint (ie: heavy gauge cable) should be at-
tached without damaging the building. DO NOT
use the gas piping or electrical conduit for the at-
tachment of the permanent end of the restraint!
Use anchor bolts in concrete or cement block. On
wooden walls, drive hi test wood lag screws into
the studs of the wall.
If the oven is moved from its regular location, the
restraint must be reconnected when theoven isre-
turned.
D calibration of the thermostat
D adjustment of the doors
D leveling
1. Mount the supplied bracket to the leg bolt just
below the power cord.
D tightening of fasteners.
No installation should be considered complete
without proper inspection, and if necessary, ad-
justment by qualified installation or service per-
sonnel.
2. Attach the clip on restraining cable to the
mounting bracket.
Back of Oven
Restraint Cable
Bracket
Double stacked unit shown. Use the same procedure for
single units.
Figure 8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Safety Information
THE INFORMATION CONTAINED IN THIS SEC-
TION IS PROVIDED FOR THE USE OF QUALIFIED
OPERATING PERSONNEL. QUALIFIED OPERAT-
ING PERSONNEL ARE THOSE WHO HAVE
CAREFULLY READ THE INFORMATION CON-
TAINED IN THIS MANUAL, ARE FAMILIAR WITH
THE FUNCTIONS OF THE OVEN AND/OR HAVE
HAD PREVIOUS EXPERIENCE WITH THE OP-
ERATION OF THE EQUIPMENT DESCRIBED. AD-
HERENCE TO THE PROCEDURES RECOM-
MENDED HEREIN WILL ASSURE THE
ACHIEVEMENT OF OPTIMUM PERFORMANCE
AND LONG, TROUBLE-FREE SERVICE.
SAFETY TIPS
For your safety read before operating
General safety tips:
D If the oven needs to be moved for any reason,
the supply cord must be disconnected from the
unit before removing the restraint cable. Recon-
nect the restraint after the oven has been re-
turned to its original location.
D DO NOT remove the control panel cover unless
the oven is unplugged.
Please take the time to read the following safety
and operating instructions. They are the key to the
successful operation of your Blodgett conveyor
oven.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Solid State Manual Control
CONTROL DESCRIPTION
1. SELECTOR SWITCH --- controls power to the
oven for high fan, low fan or cool down.
2. OVEN READY LIGHT --- when lit indicates
burner operation. When the light goes out the
oven has reached operating temperature.
1
3. SOLID STATE THERMOSTAT - allows an infi-
nite selection of temperatures from 150-550_F
(66-288_C). (infinite control shown)
4. TIMER --- activates an electric buzzer that
sounds when the cook time expires.
5. LIGHTS SWITCH --- controls interior lights.
2
6. CIRCUIT BREAKER SWITCH --- controls pow-
er to the oven.
3
4
OPERATION
1. Turn the SELECTOR Switch (1) to either HIGH
FAN or LOW FAN. The blower and control com-
partment cooling fan operate and are con-
trolled automatically by the action of the
doors.
2. Set the SOLID STATE THERMOSTAT (3) to the
desired setting or temperature.
3. Preheat until the OVEN READY LIGHT (2)
goes out.
4. Load product into the oven. Determine cook
time and set the TIMER (4).
5. When the buzzer sounds, remove the product
from the oven. Turn the TIMER knob (4) to OFF
to silence the buzzer.
5
6. Turn the SELECTOR Switch (1) to OVEN OFF.
Oven Cool Down:
1. Turn the SELECTOR Switch (1) to COOL
DOWN.
NOTE: The doors may be opened to speed the
6
cooling process.
Oven Shut Down:
1. Turn the SELECTOR SWITCH (1) to OVEN OFF.
Figure 9
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Solid State Digital Control
CONTROL DESCRIPTION
1. SELECTOR SWITCH --- turns power to the oven
on or off. Allows selection of Cook or Cool Down
Modes and fan speed (if applicable).
2. DISPLAY --- displays time or temperature and
other information related to oven function.
1
3. HEAT LAMP --- lights when heater is on.
4. PULSE LAMP --- lights when Pulsed Fan Mode
is turned on.
5. HOLD LAMP --- lights when Hold Mode is
turned on.
2
6. DIAL --- used to enter set points in display
7. START/STOP KEY --- starts or stops the timer.
8. TIME KEY --- used to show time in the display.
9. TEMP KEY --- used to show set temperature in
the display.
NOTE: Actual temperature is shown while the
TEMP key is held down.
10. HOLD KEY --- turns Hold Mode on or off.
11. PULSE KEY --- turns Pulse Mode on or off.
12. LIGHTS SWITCH --- controls interior lights.
4
5
3
8
6
9
7
13. CIRCUIT BREAKER SWITCH --- controls pow-
er to the oven.
11
10
12
13
Figure 10
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Solid State Digital Control
PROGRAMMING
Cook with Hold:
NOTE: HOLD light is on when hold mode is on
and off when hold mode is off.
To set the cook temperature:
1. Press TEMP (9) key.
2. Rotate dial (6) to enter temperature.
1. Turn SELECTOR switch (1) to the desired po-
sition.
2. Enter the cook time and temperature.
3. Press the HOLD key (10). Enter the hold tem-
perature.
To set the cook time:
1. Press TIME (8) key.
2. Rotate the dial (6) to enter time.
NOTE: Time is entered in hours:minutes
(0:00) or minutes:seconds (00:00).
4. Load product into oven.
NOTE: The display reads LOAD with the oven
is near the set temperature.
To set the hold time:
5. Push the START/STOP (7) key. Timer begins
to count down.
1. Press HOLD key (10) to turn hold mode on.
NOTE: HOLD light is on.
2. Rotate dial (6) to enter the hold temperature.
3. Press START/STOP key (7)
6. When the cook timer reaches 00:00 the buzz-
er sounds and the display reads DONE. The
buzzer turns off after a few seconds. The dis-
play reads HOLD until the oven reaches the
hold temperature. Then the timer begins to
count up.
7. Push the START/STOP key (7) to stop timer.
8. Remove the product.
9. Push HOLD (10) key to turn off hold mode.
To set the pulse time:
1. Press PULSE KEY (11) to turn pulse mode on.
NOTE: Pulse light is on.
2. Rotate DIAL (6) to enter the pulse time. Pulse
time is a portion of the pre-set cook time.
OPERATION
Cook Only:
1. Turn SELECTOR switch (1) to the desired po-
sition.
2. Enter the cook time and temperature.
3. Load product into oven.
NOTE: The display reads LOAD with the oven
is near the set temperature.
4. Press the START/STOP key (7). The timer be-
gins to count down.
5. When the cook timer reaches 00:00 the buzz-
er sounds and the display reads DONE.
6. Press the START/STOP key (7) to silence the
buzzer.
7. Remove the product.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Solid State Digital Control
Cook with Pulse:
Oven Cool Down:
1. Turn the SELECTOR Switch (1) to COOL
NOTE: PULSE light is on when pulse mode is on
and off when pulse mode is off.
DOWN.
NOTE: The doors may be opened to speed the
cooling process.
Oven Shut Down:
1. Turn the SELECTOR SWITCH (1) to the de-
sired position.
2. Enter cook time and cook temperature.
3. Press PULSE KEY (11). Enter the pulse time.
A minimum of one minute must be entered to
operate.
1. Turn the SELECTOR SWITCH (1) to OVEN OFF.
NOTE: Pulse time is a portion of the cook time
and does not increase the previously
entered cook time.
4. Load product into oven.
NOTE: The display reads LOAD with the oven
is near the set temperature.
5. Push START/STOP KEY (7). The timer begins
to count down the cook time. The oven will be
in pulse mode for the set pulse time. Once the
set time has expired, the unit will automatically
switch to cook mode and continue counting
down.
6. When the cook timer reaches 00:00 the buzz-
er sounds and the display reads DONE.
7. Push the START/STOP KEY (7) to turn the
buzzer off.
8. Remove the product.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Solid State Digital Control with Humidaire
CONTROL DESCRIPTION
1. SELECTOR SWITCH --- controls power to the
oven for high fan, low fan or cool down.
2. DISPLAY --- displays time or temperature and
other information related to oven function.
3. HEAT LAMP --- lights when heater is on.
4. PULSE LAMP --- lights when Pulsed Fan Mode
is turned on.
5. HOLD LAMP --- lights when Hold Mode is
turned on.
6. DIAL --- used to enter set points in display
7. START/STOP KEY --- starts or stops the timer.
8. TIME KEY --- used to show time in the display.
9. TEMP KEY --- used to show set temperature in
the display.
NOTE: Actual temperature is shown while the
TEMP key is held down.
10. HOLD KEY --- turns Hold Mode on or off.
11. PULSE KEY --- turns Pulse Mode on or off.
12. LIGHTS SWITCH --- controls interior lights.
1
2
4
5
3
8
6
7
9
13. HUMIDAIRE START SWITCH --- activates
moisture injection for a preset period of 30
seconds.
10
11
14. HUMIDAIRE LAMP --- lights when water is be-
ing injected
15. CIRCUIT BREAKER SWITCH --- controls pow-
er to the oven.
12
13
14
15
Figure 11
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Solid State Digital Control with Humidaire
PROGRAMMING
Cook with Hold:
NOTE: HOLD light is on when hold mode is on
and off when hold mode is off.
To set the cook temperature:
1. Press TEMP (9) key.
2. Rotate dial (6) to enter temperature.
1. Turn the SELECTOR switch (1) to the desired
position.
2. Enter the cook time and temperature.
3. Press the HOLD key (10). Enter the hold tem-
perature.
To set the cook time:
1. Press TIME (8) key.
2. Rotate the dial (6) to enter time.
NOTE: Time is entered in hours:minutes
(0:00) or minutes:seconds (00:00).
4. Load product into the oven.
NOTE: The display reads LOAD when the
oven is near the set temperature.
To set the hold time:
5. Push the START/STOP (7) key. Timer begins
to count down.
1. Press HOLD key (10) to turn hold mode on.
NOTE: HOLD light is on.
2. Rotate dial (6) to enter the hold temperature.
3. Press START/STOP key (7)
6. When the cook timer reaches 00:00 the buzz-
er sounds and the display reads DONE. The
buzzer turns off after a few seconds. The dis-
play reads HOLD until the oven reaches the
hold temperature. Then the timer begins to
count up.
7. Push the START/STOP key (7) to stop timer.
8. Remove the product.
9. Push HOLD (10) key to turn off hold mode.
To set the pulse time:
1. Press PULSE KEY (11) to turn pulse mode on.
NOTE: Pulse light is on.
2. Rotate DIAL (6) to enter the pulse time. Pulse
time is a portion of the pre-set cook time.
OPERATION
Cook Only:
Cook with Pulse:
NOTE: PULSE light is on when pulse mode is on
and off when pulse mode is off.
1. Turn the SELECTOR switch (1) to the desired
position.
1. Turn the SELECTOR SWITCH (1) to the de-
sired position.
2. Enter cook time and cook temperature.
3. Press PULSE KEY (11). Enter the pulse time.
A minimum of one minute must be entered to
operate.
2. Enter the cook time and temperature.
3. Load product into the oven.
NOTE: The display reads LOAD when the
oven is near the set temperature.
4. Press the START/STOP key (7). The timer be-
gins to count down.
NOTE: Pulse time is a portion of the cook time
and does not increase the previously
entered cook time.
5. When the cook timer reaches 00:00 the buzz-
er sounds and the display reads DONE.
6. Press the START/STOP key (7) to silence the
4. Load product into the oven.
buzzer.
NOTE: The display reads LOAD when the
oven is near the set temperature.
7. Remove the product.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Solid State Digital Control with Humidaire
5. Push START/STOP KEY (7). The timer begins
The amount of water injected during the Humid-
aire cycle may be adjusted as follows:
to count down the cook time. The oven will be
in pulse mode for the set pulse time. Once the
set time has expired, the unit will automatically
switch to cook mode and continue counting
down.
1. Check the pressure gauge on the back of the
oven while the water is dispensing. The pres-
sure should be no higher than 3 psi. If less
moisture is desired, the pressure can be set
below 3 psi.
2. To adjust the water pressure, loosen the lock-
nut on the pressure regulator.
6. When the cook timer reaches 00:00 the buzz-
er sounds and the display reads DONE.
7. Push the START/STOP KEY (7) to turn the
buzzer off.
Turn the adjusting screw counter clockwise to
decrease the water pressure.
8. Remove the product.
Turn the adjusting screw clockwise to in-
crease the water pressure if it is below 3 psi.
Oven Cool Down:
NOTE: Increasing the water pressure will in-
crease the amount of water injected
during the humidaire cycle. Decreasing
the pressure will decrease the water in-
jected during the humidaire cycle.
1. Turn the SELECTOR Switch (1) to COOL
DOWN.
NOTE: The doors may be opened to speed the
cooling process.
3. Reset the locknut on the regulator.
4. Recheck the water pressure.
Oven Shut Down:
1. Turn the SELECTOR SWITCH (1) to OVEN OFF.
WARNING!!
The Humidaire Function:
Setting the pressure above 3 psi will lead
to excessive water in the oven.
Moisture may be injected into the oven cavity at
any time during the cook cycle.
1. Press the HUMIDAIRE START SWITCH (13).
Water injects into the oven cavity for 30 sec-
onds. After the water stops injecting, the mo-
tor automatically turns off for 30 seconds. This
enables the moisture to saturate the product.
Once the humidaire cycle is complete, the
oven resumes normal operation.
Water Pressure
Adjustment
Screw
Locknut
NOTE: The oven must be above 230_F
(110_C) for humidaire to operate.
Rear view of oven
Figure 12
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
CH-Pro3 (Solid State Programmable Digital Control)
COMPONENT DESCRIPTION
1. SELECTOR SWITCH --- controls power to the
oven for high fan, low fan or cool down.
2. TIME D ISPLAY --- gives cook time.
1
3. TIME ARROW KEYS --- press to enter cook and/
or pulse times.
4. READY INDICATOR --- when lit indicates the
oven has reached the setpoint temperature
and product may be loaded.
5. TEMPERATURE DISPLAY --- gives cook and
hold temperatures.
6. HEAT INDICATOR --- when lit indicates the
oven is heating.
7. TEMPERATURE ARROW KEYS --- press to en-
ter cook and hold temperatures.
8. HOLD KEY --- turns hold mode on or off.
9. TEMP KEY --- press to display actual oven
temperature.
10. FAN KEY --- turns pulse mode on or off. The
LED above the fan key is always on.
11. PRODUCT KEYS --- three programmable keys.
12. MANUAL PRODUCT KEY --- default product key
used for manual operation.
13. START KEY --- press to begin a cook cycle.
2
4
5
3
7
6
8
10
9
12
15
11
13
14. PROGRAM KEY --- press to enter program-
ming mode and save programmed settings.
15. STOP KEY --- press to silence audible alarms
and cancel cook cycles.
14
16
17
16. LIGHTS SWITCH --- controls interior lights.
17. CIRCUIT BREAKER SWITCH --- controls pow-
er to the oven.
Figure 13
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
CH-Pro3 (Solid State Programmable Digital Control)
MANUAL OPERATION
When the oven reaches the hold temperature
the time display resets to 00:00 then begins to
NOTE: Press the arrow keys to change the cook
time and temperature at any point during-
manual operation.
count up the hold time. The fan cycles with
heat demand in the hold mode.
8. Press the STOP KEY (15) to stop the timer.
9. Remove the product.
Cook Only:
1. Turn the SELECTOR SWITCH (1) to the de-
sired position.
10. Push the HOLD KEY (8) to turn off hold mode.
2. Press the TIME ARROW KEYS (3) to enter the
cook time.
3. Press the TEMPERATURE ARROW KEYS (7)
to enter the cook temperature.
4. The READY INDICATOR (4) lights when the
oven is at the set temperature. Load product
into the oven.
5. Press the START KEY (13). The TIME DISPLAY
(2) counts down. The manual key LED flashes.
6. When the cook time expires the LEDs and
both displays flash and an audible alarm
sounds. Press the STOP KEY (15) to silence
the alarm.
Cook with Pulse:
1. Turn the SELECTOR SWITCH (1) to the de-
sired position.
2. Press the TIME ARROW KEYS (3) to enter the
cook time.
3. Press the TEMPERATURE ARROW KEYS (7)
to enter the cook temperature.
4. Press the FAN KEY (10) for five seconds. The
TEMPERATURE DISPLAY (5) goes blank. The
fan key LED flashes. Use the TIME ARROW
KEYS (3) to enter the pulse time.
NOTE: Pulse time is a portion of the cook time
and does not increase the previously
entered cook time.
7. Remove the product.
5. Press the FAN KEY (10) again. The TEMPERA-
TURE DISPLAY (5) lights.
6. The READY INDICATOR (4) in the temperature
display lights when the oven is at the set tem-
perature. Load product into the oven.
7. Press the START KEY (13). The manual key
LED flashes. The TIME DISPLAY (2) counts
down the cook time. The fan cycles on for 30
seconds then off for 30 seconds until the set
pulse time has expired.
8. When the pulse time expires both displays
flash and an audible alarm sounds. Press the
STOP KEY (15) to silence the alarm.
Cook with Hold:
1. Turn the SELECTOR SWITCH (1) to the de-
sired position.
2. Press the TIME ARROW KEYS (3) to enter the
cook time.
3. Press the TEMPERATURE ARROW KEYS (7)
to enter the cook temperature.
4. Press and hold the HOLD KEY (8) then re-
lease. Use the TEMPERATURE ARROW KEYS
(7) to enter the hold temperature. The hold key
LED lights. Press the hold key again to exit the
hold mode.
5. The READY INDICATOR (4) lights when the
oven is at the set temperature. Load product
into the oven.
6. Press the START KEY (13). The TIME DISPLAY
(2) counts down. The manual key LED flashes.
7. When the cook time expires both displays
flash and an audible alarm sounds for several
seconds then self cancels. The hold key LED
flashes. The time display begins to count up
while the oven cools to the hold temperature.
9. Remove the product.
Oven Cool Down:
1. Turn the SELECTOR Switch (1) to COOL
DOWN.
NOTE: The doors may be opened to speed the
cooling process.
Oven Shut Down:
1. Turn the SELECTOR SWITCH (1) to OVEN OFF.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
CH-Pro3 (Solid State Programmable Digital Control)
PROGRAMMING THE MANUAL KEY DEFAULT
PROGRAMMING THE PRODUCT KEYS
1. Turn the SELECTOR SWITCH (1) to the de-
sired position.
1. Turn the SELECTOR SWITCH (1) to the de-
sired position.
2. Press the MANUAL KEY (12). The manual and
fan key LEDs light.
2. Press the desired PRODUCT KEY (11). The
product and fan key LEDs light.
3. Press the TIME ARROW KEYS (3) to enter the
cook time.
4. Press the TEMPERATURE ARROW KEYS (7)
to enter the cook temperature.
5. For Cook and Hold --- Press and hold the
HOLD KEY (8). Use the TEMPERATURE AR-
ROW KEYS (7) to enter the hold temperature.
The hold key LED lights. Press the hold key
again to exit the hold mode.
3. Press and hold the PROGRAM KEY (14) until
the corresponding LED flashes, approximate-
ly five seconds.
4. Press the TIME ARROW KEYS (3) to enter the
cook time.
5. Press the TEMPERATURE ARROW KEYS (7)
to enter the cook temperature.
6. For Cook and Hold --- Press and hold the
HOLD KEY (8). Use the TEMPERATURE AR-
ROW KEYS (7) to enter the hold temperature.
The hold key LED lights. Press the hold key
again to exit the hold mode.
For Cook with Pulse --- Press the FA N KEY
(10). Use the TIME ARROW KEYS (3) to enter
the pulse time. If no pulse is required, leave
pulse time at 0:00. The fan key LED flashes.
Press the fan key again to exit fan mode.
For Cook with Pulse --- Press the FAN KEY
(10). Use the TIME ARROW KEYS (3) to enter
the pulse time. If no pulse is required, leave
pulse time at 0:00. The fan key LED flashes.
Press the fan key again to exit the fan mode.
6. Press the PROGRAM KEY (14) to save the pro-
gram settings.
MANUAL KEY DEFAULT OPERATION
7. Press the PROGRAM KEY (14) to save the pro-
gram settings.
1. Turn the SELECTOR SWITCH (1) to the de-
sired position.
PRODUCT KEY OPERATION
2. Press the MANUAL KEY (12). The applicable
LEDs light.
1. Turn the SELECTOR SWITCH (1) to the de-
sired position.
3. Press the START KEY (13). The TIME DISPLAY
(2) counts down. The manual key LED flashes.
2. Press the desired PRODUCT KEY (11). The
applicable LEDs light.
NOTE: In Cook with Pulse the fan LED flashes.
3. Press the START KEY (13). The TIME DISPLAY
(2) counts down. The product key LED flashes.
NOTE: Press the arrow keys to change the
cook time and temperature at any
point during manual key operation.
NOTE: In Cook with Pulse the fan LED flashes.
4. When the cook or pulse time expires the appli-
cable LEDs and both displays flash and an au-
dible alarm sounds.
4. When the cook time expires the applicable
LEDs and both displays flash and an audible
alarm sounds.
5. Press the STOP KEY (15) to silence the alarm.
5. Press the STOP KEY (15) to silence the alarm.
NOTE: In Cook & Hold the alarm self cancels.
The oven cools to the hold tempera-
ture and the time display counts up.
NOTE: In Cook & Hold the alarm self cancels.
The oven cools to the hold tempera-
ture and the time display counts up.
6. Remove the product.
6. Remove the product.
7. Turn the SELECTOR SWITCH (1) to OFF to
7. Turn the SELECTOR SWITCH (1) to OFF to
shut down the oven.
shut down the oven.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Blodgett IQ2T Control
COMPONENT DESCRIPTION
1. OVEN POWER SWITCH --- controls power to
the oven.
2. TOP DISPLAY --- displays temperature and
other controller related information.
3. FAN HI LED --- when lit indicates the fan is run-
ning at high speed.
4. B OT TOM D ISPLAY --- displays cook time a nd
other controller related information.
1
2
20
3
5. PROG LED --- when lit indicates the controller
is in the programming mode.
6. HEAT LED --- when lit indicates the control is
calling for heat.
4
6
7
5
12
13
14
15
8
7. FAN LO LED --- when lit indicates the fan is run-
ning at low speed.
8. COOL DOWN KEY --- press to enter the cool
down mode.
9. HOLD KEY --- press to enter hold mode.
10. PROG KEY --- press to enter the programming
mode.
9
10
11
11. TOGGLE/CLEAR KEY --- press during pro-
gramming to toggle options.
16
17
12. ACT TEMP KEY --- press to display the actual
oven temperature.
13. SET TEMP KEY --- press to display the pro-
grammed cook temperature for the current
stage of the product key.
14. ENTER KEY --- press to enter new values into
product key programming. Also used to view
recovery time.
15. SCAN KEY --- completes the programming for
the current parameter and advances the con-
troller to the next parameter. Press to view time
remaining on multiple cook cycles.
16. PRODUCT LEDS --- when lit indicate which
product keys are currently in use or pro-
grammed for the current oven temperature
and fan speed.
18
19
17. PRODUCT KEYS --- assigns a key to a pro-
grammed recipe and begins a programmed
cooking process.
18. SHELF KEYS --- assigns a shelf key.
19. LIGHTS SWITCH --- controls interior lights.
20. CIRCUIT BREAKER SWITCH --- controls pow-
er to the oven.
Figure 14
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Blodgett IQ2T Control
OVEN OPERATION
Oven Startup:
ture and fan speed will light. If the se-
lected product is a multiple stage rec-
ipe no other product LEDS will light.
1. Toggle the POWER SWITCH (1) to ON. The
oven preheats to the lowest programmed first
stage temperature. The LEDS (16) for all prod-
ucts with the same first stage temperature light.
NOTE: Press and hold the selected product
key for three seconds to cancel the
cook cycle for normal operation. To
cancel the cook cycle when using
shelf timing, press and hold the
SHELF KEY (18) for 3 seconds or
press TOGGLE/CLEAR (11) and the
corresponding shelf key.
While the unit preheats the TOP DISPLAY (2)
gives the set temperature. The BOTTOM DIS-
PLAY (4) reads Lo if the oven is more than 10_
below setpoint. When the oven reaches ¦10_
of the preheat temperature an alarm sounds
and the bottom display reads Ready.
3. When the cook time expires an alarm sounds
and the top display reads donE.
Single Product Cooking Procedure:
4. Press the selected product key to silence the
alarm. Remove the product. If shelf timing is
used, press the flashing SHELF KEY (18) to si-
lence the alarm.
NOTE: If the led next to the desired product key is
lit skip step 1.
1. Press the desired PRODUCT KEY (17). The
oven preheats to the first stage temperature for
the selected product. When the oven reaches
¦10_ of the preheat temperature an alarm
sounds and the bottom display reads Ready.
2. Load the product into the oven. Press the de-
sired PRODUCT KEY (17).
Multiple Batch Cooking Procedure:
This procedure is for single stage recipes with the
same cook temperature and fan speed only.
NOTE: If the led next to the first desired product
key is lit skip step 1.
1. Press the first desired PRODUCT KEY (17).
The LEDS for all recipes with the same cook
temperature and fan speed will light.
If the shelf timing function is toggled on for that
product key, the top display reads SHLF and
the bottom display reads the programmed
product’s time. Press a SHELF KEY (18) to as-
sign the product to that shelf and start the
cook cycle. The top display reads SHLF, the
bottom display gives the shelf #. Within five
seconds, the top display reads SH-1, the bot-
tom display gives the remaining cook time.
The oven preheats to the cook temperaturefor
the selected product. When the oven reaches
¦10_ of the preheat temperature an alarm
sounds and the bottom display reads Ready.
2. Load the product into the oven. Press the de-
sired PRODUCT KEY (17).
If the shelf timing function is toggled on for that
product key, the top display reads SHLF and
the bottom display reads the programmed
product’s time. Press a SHELF KEY (18) to as-
sign the product to that shelf and start the
cook cycle. The top display reads SHLF, the
bottom display gives the shelf #. Within five
seconds, the top display reads SH-1, the bot-
tom display gives the remaining cook time.
If the shelf timing function is toggled off for that
product key, pressing the product key will
start the cook cycle. The TOP DISPLAY (2)
reads --- --- --- --- . The B OT TOM D ISPLAY (2)
counts down the cook time in minutes: sec-
onds.
If the shelf timing function is toggled off for that
product key, pressing the product key will
start the cook cycle. The TOP DISPLAY (2)
reads --- --- --- --- . The B OT TOM D I SPLAY (4)
counts down the cook time in minutes: sec-
onds.
NOTE: If the selected product has a cook time
of greater than 59:59 the top display
r ead s Hr --- --- for the total number of
hours. The bottom display counts down
the cook time in minutes:seconds.
NOTE: If the selected product is a single stage
recipe the LEDS for all single stage
products with the same cook tempera-
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Blodgett IQ2T Control
3. Load the second product. Press the appropri-
ate PRODUCT KEY (17). Press a SHELF KEY
(18) to activate shelf timing.
Oven Cool Down:
1. Close the oven door. Press the COOL DOWN
KEY (8).
NOTE: Cool down cannot be activated with the
oven door open. Once the cool down cycle
has begun the doors may be opened to
speed the cooling process.
NOTE: Only products with lighted LEDS may
be selected.
4. The top display reads SHLF. The bottom dis-
play gives the numbers of the shelves that
have been assigned. Within five seconds the
shelf with the least amount of time remaining
is displayed. The led for the product with the
least time remaining flashes faster than the led
for the other products.
NOTE: To view the remaining cook time for
the other products press and hold the
SCAN KEY (15). The bottom display
cycles through the remaining cook
times for each product. Only the led
for the product with the cook time dis-
played will be lit.
5. When a cook time expires an alarm sounds.
The top display reads donE. The led for the fin-
ished product lights. All other LEDS are dark.
6. Press the SHELF KEY (18) for the finished
product to silence the alarm. Remove the
product. Close the oven door. The TOP DIS-
PLAY (2) reads SH-X for the shelf with the least
amount of cook time. The BOTTOM DISPLAY
(4) counts down the cook time for the other
product.
7. When the cook time expires an alarm sounds
and the top display reads donE.
8. Press the SHELF KEY (18) to silence the
alarm. Remove the product.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Blodgett IQ2T Control
PROGRAMMING SINGLE STAGE RECIPES
Entering the Programming Mode:
Programming the Cook Temperature:
1. The top display reads C t --- 1. The bottom dis-
play gives the current cook temperature. Use
the product keys to enter the desired cook
temperature.
2. Press the SCAN KEY (15) to advance the pro-
gramming mode to fan speed.
1. Press and hold the PROG KEY (10). The top
display reads CodE.
2. Use the product keys to enter the program-
ming access code: 3 1 2 4. Press the ENTER
KEY (14). The top display reads Prod.
Programming the Fan Speed:
3. Press the desired product key followed by the
ENTER KEY (14).
1. The top display reads SPd1. The bottom dis-
play gives the current fan speed. Press the
TOGGLE/CLEAR KEY (11). The bottom dis-
play toggles between HI and Lo.
NOTE: During the programming process you may:
Press the TOGGLE/CLEAR KEY (11) to
erase the current setting or toggle be-
tween specific settings. Press the SCAN
KEY (15) to move to the next programming
function keeping the current setting the
same. Press the PROG KEY (10) to exit the
programming mode.
2. Press the SCAN KEY (15) to advance the pro-
gramming mode to the fan cycle time.
Programming the Fan Cycle Time:
There are 3 options for fan cycle time: Pulse, Heat
and Full. Pulse allows the fan to turn on and off as
programmed. Heat allows the fan to operate with
heat only. Full provides continuous fan operation.
Programming the Cook Time:
1. The top display reads P1:__. The bottom dis-
play gives the current programmed cook time
for stage 1 in minutes:seconds. Press the
TOGGLE/CLEAR KEY (11). Use the product
keys to enter the new cook time. Press the EN-
TER KEY (14) to save the new cook time.
2. The top display reads P2:__. The control is
asking for the cook time for stage 2 of this rec-
ipe. Press the TOGGLE/CLEAR KEY (11) to
enter a time of 0:00:00 for P2:.
1. The top display reads CYC1. The bottom dis-
play gives the current fan cycle. Press the
TOGGLE/CLEAR KEY (11). The bottom dis-
play toggles between PULS, HEAt and FULL.
2. If heat or full are selected press the SCAN KEY
(15) to save the new fan cycle and advance to
timing mode.
If pulse is selected press the SCAN KEY (15)
and continue with Steps 3---4 to program the
pulse cycle.
NOTE: This tells the controller that there are
no more stages for this recipe. Once
a single stage recipe has been estab-
lished the control will only allow en-
tries for one stage on all further param-
eters for this product.
3. The top display reads on --- 1. The bottom dis-
play gives the current pulse on time. Use the
product keys to enter the desired pulse on
time from 10 to 60 seconds. Press the SCAN
KEY (15).
3. Press the ENTER KEY (14) again. The top dis-
play reads P1:. The bottom display shows the
cook time.
4. Press the SCAN KEY (15) to advance the pro-
gramming mode to cook temperature.
4. The top display reads of --- 1. The bottom dis-
play gives the current pulse off time. Use the
product keys to enter the desired pulse off
time from 10 to 60 seconds. Press the SCAN
KEY (15) to advance the programming mode
to shelf mode.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Blodgett IQ2T Control
Programming the Shelf ID:
Programming Hold Mode:
The hold mode can be toggled on or off for specific
product keys.
The Shelf ID option can be turned on or off for spe-
cific product keys.
1. The top display reads HOLD. The bottom dis-
play reads the current hold mode. Press
TOGGLE/CLEAR KEY (11) to toggle between
on and off. Press the SCAN KEY (15).
2. If the hold mode is activated, the bottom dis-
play give the current hold time. Press the
TOGGLE/CLEAR KEY (11). Use the product
keys to enter the new hold time. Press the
SCAN KEY (15).
NOTE: Shelf ID is not allowed with multiple stage
recipes.
1. The top display reads SHLF. The bottom dis-
play reads the current shelf ID mode. Press
the TOGGLE/CLEAR KEY (11) to toggle be-
tween yes and no. Press the SCAN KEY (15)
to advance the programming mode to timing.
Programming the Timing Mode:
3. The bottom display gives the current hold
temperature. Press the TOGGLE/CLEAR KEY
(11). Use the product keys to enter the new
hold temperature from 140-210_F (60-99_C).
Press the SCAN KEY (15).
4. The top display reads HFAN (hold fan speed).
The bottom display gives the current hold fan
speed setting. Press the TOGGLE/CLEAR
KEY (11) to toggle between high and low.
Press the SCAN KEY (15) to exit the hold
mode programming.
There are 3 options for timing mode: Straight, Flex
and Sensitivity.
1. The top display reads tC --- 1. The bottom dis-
play gives the current timing mode. Press the
TOGGLE/CLEAR KEY (11) to toggle between
St, FL and SEns.
NOTE: Sensitivity adjusts the cook time to
compensate for any difference be-
tween the setpoint and actual temper-
ature. The lower the sensitivity value
the shorter the time adjustment. Sensi-
tivity values are set in the manager lev-
el programming.
If Shelf ID is activated, all three timing modes
are available. If Shelf ID is not activated, only
straight or flex timing modes are available.
Check all Settings (SEE Mode):
The SEE mode allows the operator to scroll through
and view settings of a particular product key.
1. Press the PROG KEY (10). The top display
reads Code.
2. Press the SCAN KEY (15) to advance the pro-
gramming mode to hold mode.
2. Use the product keys to enter the SEE access
code: 2 4 4 4. Press the ENTER KEY (14). The
top display reads SEE.
3. Press the product key you wish to view. Press
the ENTER KEY (14).
4. The control will automatically scroll through
the programmable features showing the pro-
grammed values for each.
Exiting the programming mode:
1. The top display reads Prod. Press the PROG KEY
(10). The control returns to operating mode.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Blodgett IQ2T Control
PROGRAMMING MULTIPLE STAGE RECIPES
Entering the Programming Mode:
Programming the Cook Temperature:
1. The top display reads C t --- 1. The bottom dis-
play gives the current cook temperature for
stage 1 of this recipe. Use the product keys to
enter the desired cook temperature.
2. Press the ENTER KEY (14) to save the new
cook temperature for stage 1. The top display
reads Ct --- 2.
1. Press and hold the PROG KEY (10). The top
display reads CodE.
2. Use the product keys to enter the program-
ming access code: 3 1 2 4. Press the ENTER
KEY (14). The top display reads Prod.
3. Press the desired product key followed by the
NOTE: Repeat Steps 1---2 to program the
cook temperature for additional
stages. When the cook temperature
for the final stage has been entered
the top display reads Ct---1.
ENTER KEY (14).
Programming the Cook Time:
NOTE: When multiple stage cooking is being
used, the countdown time displayed dur-
ing cooking is the sum of all stages.
3. Press the SCAN KEY (15) to advance the pro-
gramming mode to fan speed
1. The top display reads P1:__. The bottom dis-
play gives the current programmed cook time
for stage 1 in minutes:seconds. Press the
TOGGLE/CLEAR KEY (11). Use the product
keys to enter the new cook time. Press the EN-
TER KEY (14) to save the new cook time.
Programming the Fan Speed:
1. The top display reads SPd1. The bottom dis-
play gives the current fan speed. Press the
TOGGLE/CLEAR KEY (11). The bottom dis-
play toggles between HI and Lo.
2. The top display reads P2:__. The control is
asking for the cook time for the second stage
of this recipe. Repeat Step 1 for each addition-
al stage.
2. Press the SCAN KEY (15) to advance the pro-
gramming mode to the fan cycle time.
3. When the cook times for all stages are pro-
grammed, press the TOGGLE/CLEAR KEY
(11) to clear the bottom display.
NOTE: This tells the controller that there are
no more stages for this recipe. Once
the number of stages has been estab-
lished the control will only allow en-
tries for these stages on all further pa-
rameters for this product.
4. Press the ENTER KEY (14) again. The display
reads P1:. The bottom display shows the cook
time.
5. Press the SCAN KEY (15) to advance the pro-
gramming mode to cook temperature.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Blodgett IQ2T Control
Programming the Fan Cycle Time:
Programming the Timing Mode:
NOTE: It may be necessary to press the ENTER
KEY (14) until the top display reads tC---1.
There are 3 options for fan cycle time: Pulse, Heat
and Full. Pulse allows the fan to turn on and off as
programmed. Heat allows the fan to operate with
heat only. Full provides continuous fan operation.
There are 2 options for timing mode: Straight and
Flex.
1. The top display reads CYC1. The bottom dis-
play gives the current fan cycle for stage 1.
Press the TOGGLE/CLEAR KEY (11). The bot-
tom display toggles between PULS, HEAt and
FULL.
1. The top display reads tC --- 1. The bottom dis-
play gives the current timing mode. Press the
TOGGLE/CLEAR KEY (11) to toggle between
St, and FL.
2. Press the ENTER KEY (14) to save the new
timing mode for stage 1. The top display reads
tC --- 2.
NOTE: Repeat Steps 1---2 to program the tim-
ing mode for additional stages.
3. When the timing mode for the final stage has
been entered press the SCAN KEY (15).
2. Press the ENTER KEY (14) to save the new fan
cycle for stage 1. The top display reads CYC2.
NOTE: Repeat Steps 1---2 to program the fan
cycle for additional stages.
3. When the fan cycle for the final stage has been
entered press the SCAN KEY (15).
If no pulse cycles are programmed the control
advances to timing mode.
Programming Hold Mode:
The hold mode can be toggled on or off for specific
product keys.
If pulse is used, the control returns to the first
stage programmed for the pulse fan option.
Follow Steps 4---5 to program the pulse on
and off time.
1. The top display reads HOLD. The bottom dis-
play reads the current hold mode. Press
TOGGLE/CLEAR KEY (11) to toggle between
on and off. Press the SCAN KEY (15).
2. The bottom display give the current hold time.
Press the TOGGLE/CLEAR KEY (11). Use the
product keys to enter the new hold time. Press
the SCAN KEY (15).
3. The bottom display gives the current hold
temperature. Press the TOGGLE/CLEAR KEY
(11). Use the product keys to enter the new
hold temperature from 140-210_F (60-99_C).
Press the SCAN KEY (15).
4. The top display reads HFAN (hold fan speed).
The bottom display gives the current hold fan
speed setting. Press the TOGGLE/CLEAR
KEY (11) to toggle between high and low.
Press the SCAN KEY (15) to exit the hold
mode programming.
4. The top display reads on --- x . The bottom dis-
play gives the current pulse on time for this
stage. Use the product keys to enter the de-
sired pulse on time from 10 to 60 seconds.
Press the SCAN KEY (15).
5. The top display reads of --- x . The bottom dis-
play gives the current pulse off time. Use the
product keys to enter the desired pulse off
time from 10 to 60 seconds. Press the SCAN
KEY (15). The control advances to the next
stage programmed for the pulse fan option.
NOTE: Repeat Steps 4---5 to program cycle
times for all pulse fan stages. When the
final pulse off time has been entered the
control advances to timing mode.
Exiting the programming mode:
1. The top display reads Prod. Press the PROG
KEY (10). The control returns to operating
mode.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Blodgett IQ2T Control
MANAGER LEVEL PROGRAMMING
Entering the programming mode
Programming the setback mode
The setback mode operates as a power saving
feature. After a period of non-use (the setback
time) the oven temperature automatically de-
creases to the setback temperature. The oven will
maintain this temperature until a product key is
pressed. The minimum setback time is 20:00.
1. Press the PROG KEY (10). The top display
reads CodE.
2. Use the product keys to enter the program-
ming access code: 4 5 1 2. Press the ENTER
KEY (14). The top display reads SYS.
1. The top display reads SEtb. The bottom dis-
play gives the setback mode. To change the
setback press the TOGGLE/CLEAR KEY (11).
The bottom display toggles between YES and
no. Press the SCAN KEY (15).
Programming hold
Hold allows product to be kept warm in the oven
at a programmed time and temperature by press-
ing the HOLD KEY (9).
If no is chosen:
a) The controller advances to programming
the temperature mode.
1. Press the SCAN KEY (15). The top display
reads Hold. Press the TOGGLE/CLEAR KEY
(11) to toggle between YES and no. Press the
SCAN KEY (15).
If yes is chosen:
a) The bottom display gives the current set-
back time. Press the TOGGLE/CLEAR
KEY (11). Use the product keys to the en-
ter the desired setback time. Press the
SCAN KEY (15) to enter the new setback
time.
b) The bottom display gives the current set-
back temperature. Press the TOGGLE/
CLEAR KEY (11). Use the product keys to
the enter a setback temperature from
140_F --- 300_F. Pr e s s t h e S C A N K E Y ( 1 5 ) t o
enter the new setback and continue with
programming the temperature mode.
If no is chosen:
a) Press the SCAN KEY (15) to advance to
programming the setback mode.
If yes is chosen:
a) The top display reads HOLD. The bottom
display gives the current hold time. Press
the TOGGLE/CLEAR KEY (11). Use the
product keys to enter a hold time from 0
to 9 hours. Press the SCAN KEY (15) to
enter the new hold time (HR:MN)..
b) The top display reads HOLD. The bottom
display gives the current hold tempera-
ture. Press the TOGGLE/CLEAR KEY (11).
Use the product keys to enter a hold tem-
perature from 140_F --- 210_F. Pr e s s t h e
SCAN KEY (15) to enter the new hold tem-
perature.
c) The top display reads H FAn. The bottom
display gives the current fan mode. To
change the fan mode press the TOGGLE/
CLEAR KEY (11). The bottom display
toggles between Hi and Lo. Press the
SCAN KEY (15) to enter the new fan mode
and continue with programming the set-
back mode.
Programming the temperature mode (_F or _C)
1. The top display reads dEg. The bottom dis-
play gives the units. To change the units press
the TOGGLE/CLEAR KEY (11). The bottom
display toggles between F and C.
2. Press the SCAN KEY (15) to enter the new
temperature units and continue programming
the shelf sensitivity.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Blodgett IQ2T Control
Programming the shelf sensitivity
ERROR CODES AND ALARMS
The controller allows the user to program a sensi-
tivity value (0---9) for each shelf position. The sen-
sitivity value will shorten or stretch cook time de-
pending upon shelf position.
NOTE: The error codes will appear in the top dis-
play. All error codes are accompanied by
an audible alarm.
Hi
Oven temperature is more than
40_F above the highest setpoint.
NOTE: SEN1 is the top shelf position, SEN5 is the
bottom shelf position.
Prob
Probe failure.
1. The display reads SEN1.
HEAT ERR From a cool start (below 140_F), the
oven takes more than 10 minutes to
climb from 150-300_F. Pr e s s t h e
TOGGLE/CLEAR KEY (11) to clear
the prompt. This code indicates a
problem with the system. Contact a
service technician.
2. Press the TOGGLE/CLEAR KEY (11) to clear
the current value to the desired value. Use the
product key numbers to input a new sensitivity
value.
3. Press the SCAN KEY (15) to advance to the
next shelf position, SEN2.
FAN ERR
Indicates a fan failure during a call
for heat. Press the TOGGLE/CLEAR
KEY (11) to clear the alarm. The FAN
ERR display remains active. Press
the TOGGLE/CLEAR KEY (11) again
to clear the message and return the
system to normal operation. If con-
dition persists turn off the oven and
contact a service technician.
4. Repeat steps 2---3 for all five shelf positions.
Exiting the programming mode
1. The top display reads SYS. Press the PROG
KEY (10). The control returns to the operating
mode.
FANC ERR Indicates a contact failure has oc-
curred in the fan control circuit.
Press the TOGGLE/CLEAR KEY(11)
to clear the alarm. The FANC ERR
display remains active. Press the
TOGGLE/CLEAR KEY (11) again to
clear the message and return the
system to normal operation. If con-
dition persists turn off the oven and
contact a service technician.
DOOR OPEN The controller senses the door is
open. Close the door. If the door is
closed contact a service technician.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
General Guidelines for Operating Personnel
COOK TIMES AND TEMPERATURES
Preheating the oven
OPERATING TIPS
Pans and Racks
Always preheat the oven before baking or roast-
ing. We recommend preheating 50_F (10_C)
above the cook temperature to offset the drop in
temperature when the doors are opened and cold
product is loaded into the oven. Set the thermostat
to the cook temperature after the product is
loaded.
Product or pan height determines how many
racks are used. The oven holds up to 10 18” x 26”
(45.7 x 66.0 cm) bun pans.
Load the oven from the bottom, centering thepans
on the rack. Never place a pan or aluminum foil on
the bottom of the oven. This obstructs the flow of
air and results in uneven baking and roasting.
NOTE: For frozen product, preheat the oven
100_F (38_C) above the cook tempera-
ture.
Roasting
To reduce shrinkage when roasting, place meat
directly on the racks. Place a sheet pan one-half
full of water in the bottom rack position. The water
evaporates, increasing humidity in the oven
chamber. The pan catches grease from the meat,
making oven cleaning easier.
Cook Temperatures
Generally, cook temperatures should be 50_F
(10_C) lower than deck or range oven recipes. If
the edges of the product are done but the center
is raw, or if there is color variation, reduce the ther-
mostat setting another 15---25_F (10---15_C). Con-
tinue to reduce the cook temperature on succes-
sive loads until the desired results are achieved.
Baking
Weigh the product to ensure equal distribution in
each pan. Varying amounts of product will cause
uneven baking results.
NOTE: Cooking at excessive temperatures will
not reduce cook time, it will produce un-
satisfactory baking and roasting results.
Fans
The fan must be operating for the oven to heat.
Use the Pulse Plus feature to allow light or liquid
product to set in the pan and to avoid rippling to-
wards the fan. If your oven is not equipped with
this feature use the following procedure.
Cook Time
Check the product in about half the time recom-
mended for deck or range oven recipes. Record
times and temperatures which provide best re-
sults for future reference.
1. Preheat the oven 25_F (15_C) above the bak-
ing temperature.
NOTE: Cook time will vary with the amount of
product loaded, the type of pan and the
temperature.
2. Load the oven with product. Close the doors.
3. Set the thermostat to the baking temperature.
4. Turn the oven off.
5. Allow the product to set for 5---7 minutes with
the fan off. The residual heat in the oven sets
the product.
6. Turn the oven on for the remainder of thebake.
Lights
Turn the oven lights off when not viewing the prod-
uct. Leaving the lights on for extended periods of
time shortens the bulb life considerably.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning and Preventative Maintenance
DAILY CLEANING
5. Wipe around the fan with a damp towel.
6. Soak racks, supports and baffle in a solution
of non-toxic, non-caustic, food safe, commer-
cial oven cleaner. Allow to soak overnight if
necessary.
Oven Cool Down:
1. Turn the oven to COOL DOWN.
NOTE: The doors may be opened to speed the
cooling process.
7. Reinstall parts.
Cleaning the exterior
Clean temperature probe
1. Saturate a cloth with a mild soap and water
mixture. Wipe the oven when it is cold.
2. Dry the oven with a clean cloth.
3. Heat tint and heavy discoloration may be re-
moved with any non-toxic, non-caustic, com-
mercial oven cleaner and stainless steel polish.
1. Use a damp towel to wipe the probe. Handle
with care.
Clean cooling fan
1. Brush off the cooling fan located on the back
of the oven behind the control compartment.
PREVENTATIVE MAINTENANCE
Annual Maintenance
Cleaning the interior
Deposits of baked on splatter may be removed with
any non-toxic, non-caustic, food safe, commercial
oven cleaner.
The following checks should be part of an annual
scheduled maintenance. This maintenancemust
be performed by an authorized service agency.
Contact your local Blodgett service company, a
factory representative or the Blodgett Oven com-
pany.
1. Apply cleaner following the manufacturer’s di-
rection. Always rub with the grain of the metal.
WEEKLY CLEANING
1. Remove any loose debris or particle buildup
from the racks, rack supports, baffle, blower
wheel and temperature probe.
1. Check venting system.
2. Check temperature calibration.
3. Adjust and grease door switch for proper clo-
sure.
MONTHLY CLEANING
4. Clean any debris out of control tray. Check for
loose connections. Replace any discolored
connections.
5. Retorque all electrical connections between
the element and contactors.
Clean racks, rack supports, baffle and blower
wheel
1. Remove the racks, rack supports and baffle.
2. Hold the blower wheel with a gloved hand.
3. Use an L-shaped brush to clean the fins on the
blower wheel.
WARNING!!
4. Use a hand brush to clean the center portion
of the blower wheel.
Always disconnect the appliance from the
power supply before servicing or cleaning.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Troubleshooting Guide
POSSIBLE CAUSE(S)
SUGGESTED REMEDY
SYMPTOM: Heating elements do not come on.
S Oven not plugged in.
S Plug in electrical supply cord.
S Set the control panel to COOK or OVEN ON.
S Set to desired cook temperature.
S Close doors.
S Power switch on the control panel is off.
S Control set below ambient temperature.
S Doors are open.
S Computerized controls --- error code on display. S *
SYMPTOM: Oven does not come to ready.
S The oven has not reached preheat temperature. S Wait for oven to reach preheat temperature.
S Fan delay feature may be activated, ifapplicable. S Deactivate fan delay feature.
S Internal problem with main temperature control. S *
SYMPTOM: Convection fan does not run.
S Oven is not plugged in.
S Plug in electrical supply cord.
S Set the control panel to COOK or OVEN ON.
S Reset the breaker.
S Oven is not set to the cook mode.
S Circuit breaker tripped.
S Fan delay feature may be activated, ifapplicable. S Deactivate fan delay feature.
S Doors are open
S Close doors.
SYMPTOM: General baking problems.
S Computerized controls --- incorrect product
S Reprogram control per Operation section.
S *
programming.
S Thermostat out of calibration.
*Denotes remedy is a difficult operation and should be performed by qualified personnel only. It is recommended, however, that
All repairs and/or adjustments be done by your local Blodgett service agency and not by the owner/operator. Blodgett cannot as-
sume responsibility for damage as a result of servicing done by unqualified personnel.
WARNING!!
Always disconnect the power supply before cleaning or servicing the oven.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER
INSERT
WIRING DIAGRAM
HERE
Download from Www.Somanuals.com. All Manuals Search And Download.
|