u s e r ’ s m a n u a l
B Z E - 1 0 A
H a l f – D I N 1 0 B a n d S l i d e C o n t r o l
P r e - A m p E q u a l i z e r
w i t h S u b w o o f e r B o o s t C o n t r o l
Download from Www.Somanuals.com. All Manuals Search And Download.
t a b l e o f c o n t e n t s
2
general features
precautions
3
features and specifications
mounting and installation
system wiring
4-5
6
7-8
9
troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
g e n e r a l f e a t u r e s
· 10 Band Graphic Equalizer
· Rotary Subwoofer Boost Control
with Active Electronic Adjustable Crossover
· Rotary Fader Control
· Full Night Illumination
· Compact 1/2 DIN Chassis Size
2
· Front Panel DVD Input Jack
· 2 RCA Input Jacks
· 6 RCA Signal Output Jacks (2 Front/2 Rear/ 2 Subwoofer)
· Electronic Crossover Adjustable to 80, 120 or 160Hz @12dB
· Frequency Response: 20Hz–20kHz
Download from Www.Somanuals.com. All Manuals Search And Download.
P r e c a u t i o n s
Never drive with the volume raised so high you cannot hear what is occurring in traffic around you,
Be aware that repeated exposure to excessive volume levels can permanently damage your hearing!
Keep all electronics away from moisture, dust, extreme heat or extreme vibrations.
Blitz Audio products are capable of sound pressure levels in excess of 150dB.
Continuous exposure to sound pressure levels over 100 dB may cause permanent loss of hearing.
Use common sense and PRACTICE SAFE SOUND.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
f e a t u r e s a n d s p e c i f i c a t i o n s
30 Hz
60 Hz
120 Hz
250 Hz
500 Hz
1
kHz
2
kHz
4
kHz
8
kHz
16 kHz
Fader
Subwoofer
10
0
DEF
PWR
10
DVD
F
R
MIN
MAX
4
SUB
FRONT
REAR
LINE INPUT
80
120
160
Hz
L
R
L
R
L
R
L
R
Download from Www.Somanuals.com. All Manuals Search And Download.
f e a t u r e s a n d s p e c i f i c a t i o n s
1 fader control
2 subwoofer output control
Rotary mechanism to control the balance between the front and rear speakers. This fader will
override the fader in your car stereo.
Source voltage
Load impedance
14.4 VDC
Rotary mechanism to control the amount of subwoofer gain at the predetermined crossover
point. The subwoofer can be adjusted from minimum to maximum by turning the knob.
10K Ohm
3 subwoofer active elevtronic crossover
The three position switch on the rear of the unit adjusts the crossover point for your subwoofer
system. The BZE10A features separate dual RCA outputs for the subwoofer channel so that the
subwoofers can run on a separate amplifier or separate channels of a multi-channel amplifier.
The crossover switch is adjustable to either 80, 120 or 160 Hz. Depending on your subwoofer
frequency response adjust this switch to the proper setting.
Reference voltage
Input impedance
Control frequencies
400mV
10K Ohm
30Hz / 60Hz / 120Hz/
250Hz / 500Hz / 1KHz/
2KHz / 4KHz / 8KHz / 16KHz
80/120/160 Hz
4 night illumination
The BZE10A features full night illumination in blue color. The illumination comes on when the
power is applied to the unit. The illumination is present around the fader and subwoofer knobs.
Each band control also features an LED in the center for illumination.
5 frequency band control
The BZE10A has 10 bands of frequency control attenuated by individual slides. The BZE10A
is a full octave equalizer. The bandwidth controls are 30Hz, 60Hz, 120Hz, 250Hz, 500Hz, 1KHz,
2KHz, 4KHz, 8KHz, and 16KHz. The center detent position represents 0dB boost. By sliding the
fader up or down you can either increase (up) or decrease (down) the amount of boost by 10dB.
Your personal preference is the general rule to set the equalizer band controls. The BZE10A will
allow you to tailor the sound to your particular listening pleasure and will help compensate for
unwanted peaks and dips found in car music systems.
Subwoofer frequency
crossover points
Filter roll off
5
12dB per octave 2nd
order butter worth
10dB boost/cut
20Hz-20KHz
6 DVD input jack (3.5mm)
7 equalizer control
Connect your portable DVD player to the DVD input jack on the front panel by a stereo path
cord with a stereo mini plug at both ends. Turn on your DVD player and then turn on the
equalizer.
When depressing the DEF switch to the on position, the equalizer controls are defeated and are
not being deployed. Amplifier operation at this point is essentially flat. When releasing this
switch to the off position the equalizer controls are once again employed and the amplified
signal is set to the equalizer frequency band settings.
Control range
Frequency response
8 rear panel input controls
The BZE10A accepts the Low Level High Impedance RCA Inputs. If your radio has RCA jack
outputs use these to input the signal into the BZE10A RCA inputs. By doing this you will be
bypassing the fader control of your head unit and the fader operation will be controlled by the
BZE10A. This will also allow you to use the speaker outputs of your radio to power your front
speaker if you so choose, eliminating the need for a separate amplifier for your front speakers.
(This is really only recommended if your head unit is a high power model otherwise you will
lose the front staging effect because the rear speakers attached to your amplifier will outplay
your front speakers being driven by the head unit. You will also not have any eqaulizer effect
on the front speakers playing through the head unit.)
Signal to noise ratio
90dB (A -Wtd)
Input sensitivity for 200mV output
Power requirement
400mV
11-16 volts negative ground
178 x 145 x 25mm
Dimensions (WDH)
rear panel output controls
There are six RCA outputs jacks. The six RCA output jacks are divided into three segments. The
first segment controls the front output of the amplifier, the second segment controls the rear
output of the amplifier. The third segment controls the subwoofer amplification. You do not
have to use all six outputs for the BZE10A to operate you can choose any one pair of segment.
What the BZE10A does is to divide your input signal into six output channels. You can thus
configure your amplification system into 3 separate 2-channel amplifiers or one four-channel
amplifier for the front and rear segment and a separate subwoofer amplifier for the subwoofer
output. Or you can choose three separate two-channel amplifiers. This is the beauty of the
BZE10A. It affords you the choice of an almost innumerable amount of amplifier configurations.
Download from Www.Somanuals.com. All Manuals Search And Download.
M o u n t i n g a n d i n s t a l l a t i o n
The BZE10A is a Half DIN sized unit. It can be mounted in the dashboard with your head unit in most cases. Use of an auxiliary installation kit is needed
like those made by American international or Scoche products.
The BZE10A is also supplied with mounting brackets giving you the option to mount the equalizer under your dash, or on the console or in your glove
compartment.
There are three power wires coming out of the back of the unit. The Red wire with the inline fuse is for 12 volts DC into the unit. This wire should be
hooked up to an accessory line which turns on only when the car is running or the key of the car is in the accessory position.
The black wire is the ground wire. Attach this wire to either the same ground of your head unit or to a clean chassis point located in the dashboard or on
the fire wall. The shorter the ground wire connection the better chance of not having any interference or noise problems.
The orange wire the remote start for your amplifier. This wire should be attached to the remote turn on circuit of your amplifiers or crossover. This way
when the BZE10A is turned on it will automatically power on your amplifier system.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
S y s t e m w i r i n g
D i a g r a m A f o r R C A i n p u t c o n f i g u r a t i o n
If your radio does not have RCA output jacks as in the case of most standard
OEM radios you can use the speaker outputs from those head units to power
the BZE10A by interfacing them with a high/low level impedance adaptor like
the Pyramid Model NS60 or any of the other numerous models available. Be
sure to use the correct adaptor so that if you have a high power radio it will be
able to reduce the level low enough not to cause any noise problems in the
installation.
7
D i a g r a m A
D i a g r a m B f o r s p e a k e r l e v e l i n p u t c o n f i g u r a t i o n
D i a g r a m B
Download from Www.Somanuals.com. All Manuals Search And Download.
S y s t e m w i r i n g
D i a g r a m C f o r s a m p l e a m p l i f i e r i n s t a l l a t i o n s
D i a g r a m C
8
D i a g r a m D f o r w i r i n g d i r e c t i o n s
D i a g r a m D
Download from Www.Somanuals.com. All Manuals Search And Download.
T r o u b l e s h o o t i n g
POSSIBLE CAUSE
PROBLEM
Signal processor does not turn on.
• Remote turn-on wire has 12V.
• 12V wire has 12V
• Ground wire is properly connected
9
Level of sound is low.
• Wiring is not loose or cables
misconnected/disconnected
• RCA cables are not faulty.
Background noise is too high.
• Wiring is not loose or cables
misconnected/disconnected
• RCA cables are not faulty.
Download from Www.Somanuals.com. All Manuals Search And Download.
l i m i t e d w a r r a n t y p o l i c y
E q u a l i z e r
All Blitz products are carefully constructed and thoroughly tested before
shipment. Products purchased in the USA are warranted to be free of defects
in material and workmanship for two (2) years from the date of purchase. This
warranty is limited to the original retail purchase.
You must also include the following items:
• A copy of your sales receipt or other proof of purchase
• A brief letter indicating the problem you are experiencing
• include in your letter your return address, daytime phone number,
and R.A. number
• also include a check or money order for $15.00 for return shipping,
handling, and insurance, or provide your Visa/MC number with
expiration date.
Should the product fail due to factory defects in material or workmanship,
your unit will be repaired or replaced at the sole discretion of Blitz.
To obtain warranty service you must first call our Consumer Return Hotline
number at (718) 236-6948 to obtain a Return Authorization number. This
R.A.# must appear on the outside of your package and on all paperwork
relating to your return.
Our obligation under this warranty is limited to the repair or
replacement of the defective unit when it is returned to us prepaid.
This warranty will be considered void if the unit was tampered with,
improperly serviced, or subject to misuse, neglect, or accidental
damage.
When returning a product to us for warranty service it must be carefully packed
and shipped prepaid to:
R.A.#
Blitz Service Center
1600 63rd Street
Brooklyn, NY 11204
w w w . b l i t z a u d i o . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
|