Blaupunkt Car Stereo System RD 126 User Manual

Radio / CD  
Sevilla  
RD 126  
Operating instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Quick reference ............................ 26 Changing the memory bank (FM)......... 35 Adjusting GEO for traffic messages  
Storing stations ..................................... 35 and the warning beep ........................... 40  
Important notes ............................ 31  
Automatically storing the strongest  
Precautions ........................................... 31 stations with Travelstore....................... 36  
CD operation................................. 41  
Switching to CD operation .................... 41  
Inserting a CD ....................................... 41  
Removing a CD .................................... 41  
Selecting a title ..................................... 41  
MIX playback ........................................ 41  
Selecting the display mode .................. 41  
Storing the display mode ...................... 41  
SCAN operation .................................... 42  
Recalling stored stations ...................... 36  
Scanning stored stations with  
Telephone mute.................................... 31 Preset Scan .......................................... 36  
Traffic safety ......................................... 31  
Installation............................................. 31  
Scanning stations with Radio-Scan...... 36  
Changing the scan time........................ 36  
Selecting the seek tuning sensitivity .... 36  
Switching from stereo to mono............. 37  
PTY – Programme Type ....................... 37  
Switching PTY on/off ......................... 37  
Programme type ................................... 37  
Checking the programme type of the  
Accessories .......................................... 31  
KeyCard theft protection  
system........................................... 32  
Putting the unit into operation .............. 32  
Removing the KeyCard ........................ 32  
“Training” a second KeyCard/  
Replacing a KeyCard............................ 32  
Displaying the radio pass data ............. 32  
Short Additional Memory (S.A.M.)........ 33  
Turn On Message (T.O.M.) .................. 33  
Optical indication for extra security ...... 33  
Care of your KeyCard ........................... 33  
DSC programming ....................... 42  
Overview of the DSC factory  
settings.................................................. 44  
station ................................................ 37  
Displaying the selected programme  
Appendix ....................................... 44  
type .................................................... 37  
Selecting a programme type ............. 37  
Storing programme types.................. 38  
Scanning stations with PTY-SCAN ... 38  
PTY priority........................................ 38  
Specifications........................................ 44  
Switching the audio source ........ 33  
Radio operation with RDS ........... 34  
Receiving traffic programme  
AF - Alternative frequency .................... 34  
REG - regional programme .................. 34  
Selecting a waveband .......................... 34  
Station tuning ........................................ 34  
stations with RDS-EON................ 39  
Traffic announcement priority on/off .... 39  
Warning beep ....................................... 39  
Switching the warning beep off ............ 40  
Automatic seek tuning start  
(CD operation) ...................................... 40  
Adjusting the volume for traffic an-  
Automatic tuning  
/
....................... 34  
Manual tuning with << >>.................. 35  
Scrolling through the broadcasting net-  
works (only FM) .................................... 35  
nouncements and the warning beep .... 40  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick reference  
Switching on with the ignition being  
switched off:  
To programme the mute volume level,  
proceed as follows:  
1 Switching on/off with the ON button:  
Press ON.  
To keep on operating the set when the  
ignition is switched off (KeyCard is in-  
serted), proceed as follows:  
Press ON after the double beep tone.  
The unit will be turned on.  
Adjust the desired volume.  
When switching the set on with the ON  
button, the KeyCard has to be insert-  
ed. The unit will play with the pre-ad-  
justed volume.  
Press  
for two seconds until you  
hear a beep.  
Now this volume level is stored as your  
mute volume.  
To avoid that the battery goes flat, the  
system will be turned off automatically  
after a playback time of one hour.  
Extra function  
Memory button in the DSC menu.  
2 VOL+ / VOL-  
4 FMT  
To alter the volume.  
Press repeatedly to switch between  
the FM memory banks I, II and T  
(Travelstore).  
When pressing this button, the system  
will automatically switch to FM.  
Switching on/off with the KeyCard:  
The set has to be turned on via the ON  
button.  
Each time the set is switched on, it will  
play with the pre-adjusted volume  
(VOL FIX).  
You may also change the VOL FIX set-  
ting (see chapter “DSC programming”).  
Note:  
Read the information in chapter  
“KeyCard theft protection system”.  
Extra function FMT  
To store the six most powerful stations  
automatically with Travelstore:  
Press FMT until you hear a beep or  
“T-STORE” appears in the display. The  
storage process is finished when “T-  
STORE” disappears from the display.  
3
For instantly muting the volume.  
Switching on/off via the ignition:  
When connected correspondingly, the  
set can also be turned on and off via  
the vehicle ignition.  
After the ignition has been switched  
off, a double beep tone will remind you  
that you should remove the KeyCard  
before leaving your vehicle.  
By pressing the  
button the volume  
will be muted immediately. “MUTE” will  
appear in the display.  
The function is cancelled by pressing  
button  
or VOL+.  
When pressing VOL-, the normal vol-  
ume will be by one grade lower than  
the mute volume.  
5 M•L - toggle switch  
To toggle between medium and long  
wave reception.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6 Rocker switch  
7 Display  
Radio operation  
CD operation  
a
d
e f g hi j k l m  
b
n
/
Station search  
Up  
/
Title selection  
Up  
Down  
o
Down  
Press once to go back to the be-  
ginning of the current title.  
c
<</>> Up/Down in short intervals when AF  
is off  
Fast advance, audible (CUE).  
Hold down  
Fast reverse, audible (REVIEW).  
Hold down as long as required.  
as long as required.  
a) NDR2  
b) CD PLAY - CD operation or  
c) 1 : 52  
- Station name  
<</>> To scroll through the station net-  
works when AF is on,  
- CD time (playback time) in  
the CD mode  
- Waveband  
e.g. NDR 1, 2, 3, 4, N-JOY, FFN,  
ANTENNE ... .  
Extra rocker switch functions:  
Further setting functions with  
d) FM  
e) 6  
f) I, II, T  
- Preset button (1-6)  
- Memory bank I, II or  
Travelstore  
- A CD is inserted  
- Stereo  
- Seek tuning sensitivity  
- Alternative frequency for  
RDS operation  
AUD  
GEO  
D
C
B
>
g) CD-IN  
h)  
i) lo  
DSC MODE  
PTY  
Condition: The corresponding function  
has to be activated.  
j) AF  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
k) TA  
l) TP  
- Priority for traffic stations  
- A traffic station is being re-  
ceived  
- Programme type function  
- CD playback in random or-  
der  
For more information see chapter  
“DSC programming”.  
This flashlight can be switched off by  
pushing in the tongue and lock.  
Preset Scan  
Press SC for approximately two sec-  
onds until you hear a beep -  
“SCAN” and the name of the scanned  
station will alternately appear in the  
display. The unit will scan all stations  
stored on the preset buttons.  
To stop Scan / Preset Scan:  
Press SC once again.  
m) PTY  
n) MIX  
9 MIX  
o) T5  
- Track no. 5 is played back  
CD operation  
8 KeyCard theft protection system  
To operate the set it is necessary that  
the KeyCard is inserted.  
The Mix function is switched on if  
“MIX” appears in the display. The CD  
tracks will be played at random.  
To switch Mix on and off:  
CD-Scan  
Press SC briefly.  
You will hear a beep. “CD-SCAN” ap-  
pears in the display. The unit will scan  
all CD titles.  
Press MIX briefly.  
KeyCard  
: SC  
To stop CD-Scan:  
Press SC once again.  
For this purpose, introduce the  
KeyCard (with the contact area show-  
ing up) into the slot above the tongue  
sticking out of the unit.  
To remove the card, press first to un-  
lock.  
Radio operation  
; lo  
Scan  
Press SC briefly -  
“FM SCAN” and the name of the  
scanned station will alternately appear  
in the display. The unit will scan all sta-  
tions which can be received.  
Radio operation  
To switch the seek tuning sensitivity  
level:  
Press button briefly.  
Read also the information in chapter  
“KeyCard theft protection system”.  
To switch between mono and stereo  
reception:  
Press button for approximately two  
seconds (beep).  
Flashing KeyCard tongue  
When the radio is turned off and the  
KeyCard removed, the KeyCard  
tongue can be programmed to flash for  
optical theft protection.  
The stereo symbol  
mono playback.  
will disappear for  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
< TA (priority for traffic announcements)  
When “TA” lights up in the display, the  
system will play traffic stations only.  
Priority on/off: Press TA.  
> PTY (Programme Type)  
To recall a station: Select the desired  
waveband. On FM, adjust the corre-  
sponding memory bank and press the  
relevant preset button briefly.  
In the PTY mode, the preset buttons  
become programme type buttons. With  
each preset you can select one pro-  
gramme type, such as for example  
NEWS, SPORT, POP MUSIC, EDU-  
CATE, etc.  
Extra function preset buttons  
To store and recall a PTY programme  
type.  
= AF  
Radio operation  
On FM, you can store and recall one  
programme type on/from each preset  
button when PTY is active (“PTY”  
lights up in the display).  
?
SRC  
SRC (Source)  
When having a CD inserted, you can  
switch between radio and CD opera-  
tion.  
(Eject)  
Hold down the button for approximate-  
ly two seconds (beep) and the CD will  
eject.  
Alternative frequency during RDS op-  
eration:  
When “AF” lights up in the display, the  
system will automatically seek a fre-  
quency offering better reception of the  
same RDS programme.  
A CD slot  
When inserting a disc with the label  
side facing up, it will be pulled in auto-  
matically and transported to the play-  
back position. CD playback is adjusted  
automatically.  
AF on/off: Press AF briefly.  
Regional function on/off:  
Press the AF button for approximately  
two seconds until you hear a beep.  
“REG-ON” or “REG-OFF” will appear  
in the display (see chapter REG - re-  
gional programme).  
B DSC (Direct Software Control)  
Use the DSC function to customise  
certain programmable, basic settings  
to suit your personal needs and prefer-  
ences. See chapter “DSC program-  
ming” for more information.  
@ 1, 2, 3, 4, 5, 6 - preset buttons  
On FM, you can store six stations for  
each of the memory banks I, II and T.  
On MW/LW, you can store six stations  
each.  
CD operation  
To switch between the CD PLAY and  
TIME (playback time) display modes:  
Press AF briefly.  
To store a station: Press a preset  
button during radio operation and hold  
down until the set resumes play after  
the muting and you hear a beep.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C GEO  
To adjust the balance (left/right) and  
D AUD  
To adjust the treble and bass frequen-  
To switch the Loudness on/off:  
Press the AUD button for approximate-  
ly two seconds until you hear a beep.  
The Loudness function is active if “LD”  
appears in the display.  
fader (front/rear) with the rocker  
switch.  
cies with the rocker switch.  
For more information see chapter  
“DSC programming”.  
Treble +  
Treble –  
Bass –  
Fader front  
Fader rear  
Bass +  
Balance left  
Balance right  
The last setting will be stored automat-  
ically.  
To switch off AUD: Press button once  
again.  
If the setting remains unchanged with-  
in four seconds, the AUD setting will  
be terminated automatically.  
The last setting will be stored automat-  
ically.  
To switch off GEO: Press button once  
again.  
If the setting remains unchanged with-  
in four seconds, the display will switch  
back to the previous condition.  
Extra function AUD  
Extra function GEO  
Loudness: When listening at a low lev-  
el, the Loudness function will create a  
more natural sound by emphasising  
the low frequency range.  
Separate balance and fader settings  
for traffic messages. See chapter “Ad-  
justing GEO for traffic messages and  
the warning beep”.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important notes  
Installation  
Accessories  
Precautions  
If you would like to install your new car ster- Use only the accessories and spare parts  
eo yourself or add other audio components approved by Blaupunkt.  
to existing ones, then please read carefully  
Before starting to use your new car radio,  
please read the following information care-  
fully.  
the enclosed instructions on installation and You can use the following Blaupunkt prod-  
connection.  
In order to ensure that the set operates prop-  
ucts with this car stereo:  
Traffic safety  
As the driver of a motor vehicle, it is your  
responsibility to pay attention to the traffic  
situation at all times. Never use your car  
radio in a way that could distract you.  
Please keep in mind that you travel a dis-  
tance of 14 m per second at a speed of only  
50 km/h.  
erly it is necessary that the positive power Amplifier  
supply line is connected via the ignition and All Blaupunkt amplifiers  
the permanent +12 V lead.  
Do not ground the loudspeaker outputs!  
Telephone mute  
If you have a mobile telephone installed in  
your vehicle, radio or CD playback can be  
muted automatically when using the phone  
(telephone mute).  
“PHONE” will then appear in the display.  
When TA is active, traffic messages will al-  
ways have priority. The announcement will  
be aborted by pressing the TA button.  
Should the traffic situation become particu-  
larly demanding, we advise you not to use  
the radio.  
Always make sure that you are still able to  
hear any warning signals coming from out-  
side of the vehicle, such as police or fire  
engine sirens, so that you can react accord-  
ingly.  
Therefore, you should always select a mod-  
erate volume for playing your car radio while  
you are driving.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KeyCard theft protection system  
This car radio is supplied with one KeyCard ERR” will appear in the display. In this case  
as standard, though it can also be operated please do not make any further adjustments.  
Press << or >>.  
The display will switch to “CHANGE”.  
with a second card.  
The system will switch off after approximate-  
Push in the KeyCard. The card is re-  
leased and put in the proper position  
for being removed.  
If you have lost your KeyCard or if it was ly ten seconds.  
damaged, you can buy a new one from your When inserting another card type (e.g.  
specialised dealer.  
phone or credit card), the display will show  
Remove the first KeyCard and insert  
the new one while “CHANGE” is still  
being displayed.  
When using two KeyCards, the settings “WRONG KC” for approximately two sec-  
stored on the first card will be adopted. How- onds.  
ever, you can individually store the follow- Remove the wrong card and introduce the  
After the display indication “READY” or  
“LEARN KC”,  
ing functions:  
correct KeyCard.  
Preset button assignments, bass, treble, After the display indications “CARD ERR”  
balance and fader settings, Loudness, TA or “WRONG KC”:  
press DSC.  
Now you can also use the new KeyCard for  
operating your unit.  
(traffic announcement volume), beep vol-  
ume.  
Press ON to turn on the set.  
A maximum of two cards can be used for  
the set.  
When trying to “train” a third one, the ac-  
cess authorisation for the KeyCard not used  
for the “training” process will be deleted  
automatically.  
In addition, the settings activated before  
switching the radio off, such as the wave-  
band, station, TA priority, AF, REG ON/OFF,  
SCANTIME, seek tuning sensitivity and VOL  
FIX will also remained stored.  
This ensures that you will find your basic  
settings re-adjusted automatically as soon  
as you have inserted your KeyCard.  
Removing the KeyCard  
Never pull out the KeyCard directly!  
First, slightly push in the KeyCard.  
This releases the card and puts it in the prop-  
er position for being removed.  
Now you can pull it out.  
Displaying the radio pass data  
“Training” a second KeyCard/  
Replacing a KeyCard  
Using the KeyCard supplied with your set  
you can have the radio pass data such as  
the model name, product number (7 6 ...)  
and serial number indicated on the display  
panel.  
Putting the unit into operation  
While operating the unit with the first  
KeyCard, you can “train” a second one to  
be also used with the set:  
Turn on the set.  
Introduce the KeyCard into the slot  
with the contact area showing up  
(KeyCard tongue sticking out).  
Please refer to chapter “DSC programming  
- READ KC”.  
Insert the first KeyCard and turn on the  
set.  
The car radio is now ready for operation.  
If a wrong KeyCard is inserted, then “CARD  
Press the DSC button and select  
“LEARN KC” with  
/
.
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switching the audio source  
Short Additional Memory  
(S.A.M.)  
Optical indication for extra  
security  
Using the SRC button you can switch be-  
tween the following audio sources:  
radio and  
CD.  
The second KeyCard available from your Flashing KeyCard tongue  
specialised dealer offers you the possibility  
When the vehicle is stationary and the  
to read out any short information, which will  
be moved through the display, such as, for  
example, the phone number of your car deal-  
er or the emergency call number of your  
automobile association. Please refer to  
chapter “DSC programming - READ KC”.  
The freely selectable text with a maximum  
of 48 characters can be programmed by all  
dealers who have the required equipment  
available.  
The CD mode is only available if a disc is  
inserted.  
KeyCard removed, the KeyCard tongue can  
be switched to flash for extra anti-theft secu-  
rity.  
For this it is necessary that the positive pow-  
er supply line and the permanent +12 V lead  
are connected such as described in the in-  
stallation instructions.  
Be sure that “LED ON” is adjusted in the  
DSC mode.  
If required, please refer to chapter “DSC  
programming - LED”.  
Turn On Message (T.O.M.)  
Switching off the flashlight  
The second KeyCard available from your  
specialised dealer also allows you to dis-  
play a special turn-on message each time  
the radio is switched on.  
The freely selectable text with a maximum  
of 48 characters can be programmed by all  
dealers who have the required equipment  
available.  
The flashlight can be switched off by push-  
ing in the KeyCard and lock.  
If you would like to deactivate the flashing  
tongue with general effect, adjust the rele-  
vant item in the DSC menu to “LED OFF”.  
Care of your KeyCard  
The programmed text will be displayed each  
time you turn on your system with the sec-  
ond KeyCard.  
For a proper function of the KeyCard it is  
important that the contacts are free from any  
foreign particles. Avoid direct skin contact.  
If necessary, clean the KeyCard contacts  
using a cotton swab soaked with alcohol.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Radio operation with RDS (Radio Data System)  
The Radio Data System offers you more If “SEARCH” appears in the display when If you leave the service area of the regional  
convenience when listening to FM radio sta- switching on the radio or recalling one of the programme tuned into, or if you would like  
tions.  
stored frequencies, the unit is automatically to take advantage of the full RDS service,  
More and more radio stations have begun searching for an alternative frequency.  
to broadcast RDS information alongside “SEARCH” will disappear from the display  
switch to “REG OFF”.  
Press the AF button for approximately  
their programmes.  
when the alternative frequency has been  
two seconds until “REG OFF” appears.  
As soon as a programme has been identi- found or after the frequency band has been  
fied, the station name including a regional run through completely.  
identifier, if applicable, will appear in the dis- If the reception quality of the selected pro-  
play, for example, NDR1 NDS (regional pro- gramme becomes too bad:  
“REG ON” or “REG OFF” will be briefly dis-  
played each time the radio is switched on.  
Selecting a waveband  
gramme in Lower Saxony, Germany).  
When RDS is activated, the preset buttons  
become programme buttons. You now know  
exactly which programme you have tuned  
into, making it easy to find the desired sta-  
tion quickly.  
Tune into another station.  
With this car radio you can select between  
the following wavebands:  
FM 87.5 - 108 MHz  
REG - regional programme  
Certain radio programmes are split up at MW 531 - 1602 kHz  
times into regional programmes offering lo- LW 153 - 279 kHz  
But RDS offers you further advantages:  
cal information. The 1st programme broad-  
cast by NDR, for example, offers pro-  
grammes with different contents in the  
northern states of Germany Schleswig-  
Holstein, Hamburg and Lower Saxony at  
certain times of the day.  
If you are listening to one programme and  
move to an area where another linked re-  
gional programme becomes stronger, the  
unit will switch to that programme.  
Select the desired waveband by press-  
ing the FMT or M•L button.  
AF - Alternative frequency  
To toggle between MW and LW:  
Press M•L.  
The AF (Alternative Frequency) function  
makes sure that the strongest frequency of  
the currently selected programme is always  
tuned in automatically.  
This function is activated when “AF” appears  
in the display.  
Station tuning  
Automatic tuning  
/
Press  
cally search for the next station.  
When keeping the upper or lower part  
/
; the car radio will automati-  
In order to switch this function on or off,  
If you wish to continue listening to the first  
programme,  
/
press the AF button briefly.  
of the rocker switch depressed, seek tuning  
will speed up in upwards or downwards di-  
rection.  
press the AF button for approximately  
two seconds.  
While searching for the strongest reception  
signal, the radio may switch to mute briefly.  
“REG ON” appears in the display.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Scrolling through the broadcast-  
ing networks (only FM)  
Press the FMT button as many times  
until the desired memory bank lights  
up in the display.  
You can use the << >> buttons to tune in  
stations of your reception area.  
Storing stations  
If several programmes of the broadcasting  
networks can be received, you can scroll  
through them in forwards direction pressing  
>>, or backwards using the << button, e.g.  
NDR 1, 2, 3, 4, N-JOY, FFN, ANTENNE ...  
For this it is necessary that the stations have  
been tuned in at least once and that “AF” is  
active (lights up in the display).  
On FM, you can store six stations on the  
preset buttons 1-6 for each of the memory  
banks I, II and T.  
Seek tuning  
Up  
Down  
Down in short intervals  
(“AF” must be switched off)  
Up in short intervals  
(“AF” must be switched off)  
On MW/LW, you can store six stations each.  
Select the appropriate waveband with  
FMT or M•L.  
Tune in a station with the rocker switch  
For this purpose, you may start Travelstore  
seek operation:  
(either automatically  
<< >>).  
/
or manually  
Manual tuning with << >>  
Press FMT for two seconds; the sys-  
tem starts to run through the frequency  
band.  
Press the desired preset button until  
the radio resumes play after the mut-  
ing (takes approximately two seconds,  
confirmed by beep).  
You can also tune in a station manually.  
Condition:  
If “AF” does not light up,  
press AF.  
AF and PTY must be switched off (i.e. the  
symbols do not light up in the display).  
Now the station has been stored.  
The activated preset button is indicated in  
the display.  
With this, the requirements for selecting sta-  
tions with << >> are fulfilled.  
If necessary, deactivate these functions:  
Press AF or PTY.  
Changing the memory bank (FM)  
Manual tuning:  
Notice:  
Should you tune in a station which has al-  
ready been stored before on another  
memory bank, the corresponding preset but-  
ton and the memory bank will briefly flash in  
the display.  
You can shift between the memory banks I,  
II and T in order to store stations and recall  
them later.  
The currently selected memory bank is in-  
dicated in the display.  
Press << >>; the frequency will change  
in short intervals in downwards or up-  
wards direction.  
When holding the right or left part of the rock-  
er switch depressed, the frequency scan is  
speeded up.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Automatically storing the stron- Scanning stored stations with  
gest stations with Travelstore Preset Scan  
To select a scanned station and switch  
off the Radio-Scan function:  
Press SC briefly.  
You can automatically store the six most You can have all of the stored stations  
powerful FM stations of your current recep- scanned briefly.  
If no station is selected, the scan function  
will be automatically switched off after the  
frequency band has been run through com-  
pletely. The unit will tune in the station lis-  
tened to before starting the scan.  
tion area sorted according to their signal  
strength. This function is particularly con-  
venient on longer trips.  
To start Preset Scan:  
Press SC for approximately two sec-  
onds.  
Press the FMT button for two seconds.  
All of the stored stations of the waveband  
will be scanned one after the other. The  
scanned frequency or the station name will  
start flashing in the display. During the ac-  
“T-STORE” will appear in the display.  
The six strongest FM stations will be auto-  
matically stored on the memory bank “T”  
(Travelstore). When this process has been  
completed, the radio will play the first sta-  
tion.  
If desired, stations can also be stored  
manually on the Travelstore bank (see “Stor-  
ing stations”).  
Changing the scan time  
The scan time can be changed from be-  
tual scanning process “SCAN” will be dis- tween five to a maximum of 30 seconds.  
played.  
Please refer to chapter “DSC programming  
- SCANTIME”.  
To select a scanned station and switch  
off Preset Scan:  
Selecting the seek tuning sensi-  
tivity  
Press SC briefly.  
You can alter the automatic seek tuning  
sensitivity.  
Scanning stations with  
Radio-Scan  
Recalling stored stations  
You can recall any stored station by pres-  
sing the corresponding preset button.  
If “lo” is displayed, the radio will only pick up  
strong, local stations (low sensitivity).  
If “lo” does not light up, the radio will also  
pick up weaker, distant stations (high sen-  
sitivity).  
The sensitivity level can be altered in both  
modes (see also chapter “DSC program-  
ming”).  
You can also scan all stations which can be  
received.  
Select the waveband by pressing FMT  
or M•L. On FM, also choose the corre-  
sponding memory bank by pressing  
the FMT button as many times until the  
desired bank appears in the display.  
To start the Scan function:  
Press SC briefly.  
The scanned frequency or the station name  
will start flashing in the display. During the  
actual scanning process “SCAN” will be dis-  
played.  
Briefly press the corresponding preset  
button.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switching from stereo to mono  
Programme type  
Checking the programme type of the  
station  
If reception is poor, you may get better Use << >> to have the last selected pro-  
Press PTY for approximately two sec-  
onds.  
sound quality by switching to mono:  
gramme type displayed and to choose a new  
one.  
Press the lo button for approximately  
You can select any one of the stored types  
with the preset buttons 1 - 6.  
Condition: PTY must be active.  
Using DSC you can choose between Ger-  
man and English (see “DSC programming -  
PTY LANG”).  
All of the programme types listed below are  
available.  
The letters printed in bold are identical to  
the actual short-time indication in the dis-  
play.  
After the beep tone the display will show the  
programme type offered by the tuned in sta-  
tion.  
If “NO PTY” appears in the display, the cur-  
rent station has no PTY code.  
two seconds.  
With mono playback, the stereo sign  
disappear from the display.  
Each time the radio is switched on, stereo  
playback is activated.  
The unit will automatically switch to mono if  
the received signal is not strong enough for  
stereo playback.  
will  
Displaying the selected programme  
type  
Press << or >>.  
PTY – Programme Type  
The programme type selected last will be  
displayed briefly.  
PTY is an RDS service offered by more and  
more radio broadcasters. This feature allows  
you to select FM stations according to their  
programme type. After you have chosen the  
PTY of your preference, the corresponding  
stations can be selected either by seek tun-  
ing or using the scan function.  
NEWS  
CURRENT AFFAIRS  
INFORMATION  
SPORT  
EDUCATE  
DRAMA  
Selecting a programme type  
a) Using the preset buttons  
When PTY is switched on, you can use  
the preset buttons 1-6 to select the  
programme types stored at the factory.  
CULTURE  
Press one of the presets 1 - 6.  
SCIENCE  
VARIED  
POP MUSIC  
ROCK MUSIC  
M.O.R. M (middle of the road music)  
LIGHT M (light classical)  
CLASSICS (serious classical)  
OTHER M (other music)  
Switching PTY on/off  
The selected programme type will be  
displayed for two seconds.  
Press PTY.  
If you wish to listen to a station with  
this PTY,  
When the function is active, the programme  
type selected last will briefly appear in the  
display. “PTY” will be permanently indicat-  
ed in the lower right corner of the display  
panel.  
press  
/
to start seek tuning op-  
eration.  
PTY 16 to PTY 30 are not yet assigned.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If the system is unable to find a station of- will be released. The station received be- PTY priority  
fering the selected programme type, the dis- fore starting seek tuning will be tuned in.  
play will show “NO PTY” and a beep tone  
will be released. The station received be- Storing programme types  
Situation:  
PTY is switched on and lights up in the dis-  
play.  
fore starting seek tuning will be tuned in.  
One programme type was assigned to each  
No station offering the selected programme  
type can currently be received (with seek  
tuning or scan).  
The set will switch back to the previous sta-  
tion.  
As soon as a programme with such PTY can  
be received within the broadcasting network,  
the unit will switch over to the correspond-  
ing station for the duration of the pro-  
gramme.  
You can assign different programme types  
to each preset position. Please refer to the  
next chapter “Storing programme types”.  
of the preset buttons 1-6 at the factory.  
If desired, you can also store other availa-  
ble programme types.  
To do so, make sure that “PTY” lights up in  
the display.  
b) Using the << >> buttons of the rocker  
switch  
If necessary, press the PTY button to  
switch on the function.  
When PTY is switched on, you can se-  
lect a programme type using buttons  
<< >>.  
Select a programme type using but-  
tons << >> and  
Press << or >>; the programme  
type selected last will be displayed  
for three seconds.  
hold down the desired preset button  
(1-6) until you hear a beep.  
Example:  
German broadcasting network NDR:  
Now the selected programme type can be  
recalled by pressing this preset. For this the  
PTY function must be active.  
During this period press >> (for-  
wards) or << (backwards) to select  
the desired type.  
-
-
-
-
-
Station tuned in: NDR3.  
“PTY” lights up in the display.  
Programme type “POP” selected.  
Seek tuning is started.  
Press << or >> as many times as  
required.  
Scanning stations with PTY-SCAN  
Condition: “PTY” must appear in the display.  
The display alternately shows  
“SEARCH” and “POP”.  
If you wish to listen to a station offering  
the selected PTY,  
Press the SC button.  
All received stations offering the selected  
programme types will be scanned.  
press  
/
to start seek tuning op-  
-
No station with PTY-POP can be  
found.  
eration.  
To switch off PTY-SCAN:  
If the system is unable to find a station of-  
fering the selected programme type, the dis-  
play will show “NO PTY” and a beep tone  
Press SC once again.  
-
-
The display shows “NO PTY” and  
automatically switches back to NDR3.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Receiving traffic programme stations with RDS-EON  
-
-
NDR2 airs a PTY-POP programme.  
The abbreviation “EON” stands for En- Traffic announcement priority  
hanced Other Networks, meaning the on/off  
The system will switch to the linked  
station NDR2 for the duration of the  
“POP” programme.  
exchange of information within a radio net-  
If the priority for traffic announcement pro-  
work.  
grammes is activated, “TA” will light up in  
Many FM broadcasters offer traffic messag-  
the display.  
es for their service area at regular intervals.  
To switch the priority on or off:  
During CD operation, the set will also switch  
to the programme offering the selected PTY  
within the broadcasting network.  
After the PTY programme the system will  
remain in the radio mode.  
All traffic programme stations transmit a  
Press the TA button.  
special carrier signal alongside their pro-  
grammes, which is decoded by your car ra-  
dio. If this signal is identified, “TP” will ap-  
pear in the display (Traffic Programme).  
In addition to these, there are also stations  
which do not actually transmit traffic pro-  
grammes themselves, but by using RDS-  
EON they offer the possibility to receive the  
traffic messages broadcast by another traf-  
fic programme station in the same radio  
network.  
When pressing TA while a message is be-  
ing broadcast, this message will be interrup-  
ted. The unit will then switch back to the pre-  
vious condition. The priority for other traffic  
messages remains active.  
Please note that several buttons have no  
function while a traffic announcement is  
broadcast.  
Notice:  
As earlier mentioned, these functions are  
currently only supported by a limited number  
of RDS stations.  
Warning beep  
If you wish to have the priority for traffic an-  
nouncements activated while listening to  
one of these stations (e.g. NDR3), “TA” must  
appear on the display panel.  
If a traffic announcement is broadcast, the  
radio will automatically switch to the linked  
traffic programme station (in this case,  
NDR2) for the duration of the message and  
return to the original programme (NDR3)  
afterwards.  
If you leave the reception area of the traffic  
programme station currently tuned into, you  
will hear a warning beep after approximate-  
ly 30 seconds.  
This alarm tone will also be released when  
pressing a preset button which has no traf-  
fic programme allocated to it.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switching the warning beep off  
Adjusting the volume for traffic  
announcements and the warning  
beep  
a) Tune into another station offering traf-  
fic information:  
This volume was preset at the factory,  
though you can alter the value using the  
DSC function (see “DSC programming,  
TA VOL”).  
Press the rocker switch or  
press a preset button which has a  
traffic programme station allocated  
to it.  
Alternatively:  
Adjusting GEO for traffic mes-  
sages and the warning beep  
b) Switch off the priority for traffic an-  
nouncements:  
You can separately adjust the balance and  
fader settings for both traffic announcements  
and the warning beep.  
Press TA.  
“TA” will disappear from the dis-  
play.  
For example, it is possible to listen to traffic  
reports via the front left (right) speaker only.  
This provides the driver with the important  
traffic information without bothering the rear  
passengers too much.  
Automatic seek tuning start  
(CD operation)  
When leaving the reception area of the tuned  
in traffic programme station while listening  
to a CD, the system will automatically start  
searching for a new TA programme.  
If no such station is found within approxi-  
mately 30 seconds, CD operation will be  
stopped and a warning beep will sound. To  
switch the warning beep off, proceed as  
described above.  
To make a setting:  
During an announcement, adjust the  
balance and fader settings to suit your  
personal preferences.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD operation  
Selecting a title  
MIX playback  
This car stereo is equipped with a CD drive.  
After having inserted the CD, the activated When the MIX function has been activated,  
CD functions will appear on the display pan- the CD tracks will be played in random or-  
Switching to CD operation  
el.  
der. “MIX” will then appear in the display.  
Make sure that a disc is inserted, “CD IN”  
shows on the display panel.  
In order to switch the MIX function on or off,  
press MIX briefly.  
Press SRC to go through the available au-  
dio sources:  
Press as many times until the display  
briefly shows “CD”.  
Selecting the display mode  
You can select the desired display mode for  
CD operation:  
/
Title selection  
Up  
Down  
Inserting a CD  
“CD PLAY” – To indicate CD operation.  
Switch on the radio.  
Press once to go back to the begin-  
ning of the current title.  
“TIME”  
– The elapsed playback  
time of the title is dis-  
played, for example  
“2 : 32”.  
Insert a CD with the label facing up  
without the use of force.  
Fast advance, audible (CUE).  
Hold down  
Fast reverse, audible (REVIEW).  
Hold down as long as required.  
as long as required.  
The CD will be transported to its playing  
position automatically. CD playback will  
start.  
To switch the display mode:  
Press the AF button during CD play-  
back.  
Press the rocker switch as many times until  
you have reached the desired title.  
The number displayed beside “T” indicates  
the track number of the currently played  
title.  
Removing a CD  
The display mode and the corresponding  
setting or value will briefly show on the dis-  
play panel, e.g. “TIME”, “2 : 32”.  
Press the  
button for approximately  
one second (beep). The CD will be  
ejected.  
Storing the display mode  
To protect the CD mechanism, do not im-  
pair or try to help the automatic insertion and  
ejection of the disc in any way.  
If the CD is not removed within approximate-  
ly 30 seconds, it will be re-inserted automat-  
ically.  
You can store your preferred display mode  
which will then be active each time the ra-  
dio is switched on.  
If required,  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DSC programming  
press AF as many times until the de-  
sired setting is displayed.  
LOUDNESS Loudness - When listening  
at a low level, the Loudness  
function creates a more nat-  
ural sound by boosting the  
low frequency range.  
DSC (Direct Software Control) allows you  
to customise certain programmable, basic  
settings to suit your personal needs and  
preferences and then store them.  
The basic settings for this audio equipment  
were made at the factory.  
In the following you can find an overview of  
these settings, so that you can always reset  
to these if desired.  
Hold down the AF button until you hear  
a beep.  
LOUD 1 - Low boost  
LOUD 6 - Max. boost  
SCAN operation  
Use this function to scan all of the CD tracks.  
TA VOL  
To adjust the traffic an-  
nouncement and warning  
beep volume from between  
0 to 63.  
To start the Scan function:  
If you wish to alter any of the programming,  
Press SC.  
press DSC.  
The titles will be scanned one after the oth-  
er in ascending order.  
Use the rocker switch and the  
button to  
The message will then come  
through at this volume, if the  
standard volume is lower.  
Should the standard volume  
be higher than the TA VOL  
level, then the traffic report  
will be played slightly louder  
than the standard volume.  
select and adjust the functions described in  
the following. The display will show you the  
adjusted condition.  
To stop the Scan function:  
Press SC.  
The track currently being scanned is con-  
tinued to be played.  
SCAN will also be terminated by  
pressing one of the buttons AUD,  
GEO, DSC, SRC, , << >> or / .  
/
Select function  
<< >>  
Adjust/recall value  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPEECH  
In future many RDS radio  
stations will differentiate be-  
tween music and speech  
programmes.  
You can alter the tone for  
speech programmes from  
between “SPEECH 0 ... 4”.  
ANGLE  
BRIGHT  
Use this setting to alter the  
viewing angle to your liking  
from -1 to 0 to +1.  
LEARN KC To “train” a second  
KeyCard.  
Please read the information  
in chapter “KeyCard theft  
protection system - “Train-  
ing” a second KeyCard”.  
You can adjust the display  
brightness from between 1  
to 16. You can also select  
different values for day and  
night.  
SPEECH 0:  
Music/speech off  
READ KC  
To read out the KeyCard  
data.  
Selecting the night bright-  
ness:  
The card supplied with the  
radio is used to display the  
model name, type number  
(7 6..) and the serial  
SPEECH 1:  
Linear reproduction (bass,  
treble and Loudness set to  
“0”)  
Switch on the vehicle lights  
and programme the bright-  
ness value. The car radio’s  
lighting connector must be  
hooked up to the vehicle’s  
electric system for this to  
function properly.  
number.  
SPEECH 2-4:  
With the extra card it is pos-  
sible to display the Short  
Additional Memory (S.A.M.)  
data entered by your spe-  
cialised dealer. See chapter  
“Short Additional Memory  
S.A.M.”.  
If you remove the KeyCard  
during the reading process,  
“READ KC” will show on the  
display panel. The unit con-  
tinues to play but does not  
accept any operations ex-  
cept from being switched  
off. Re-insert the card.  
Different settings for vol-  
ume, bass and treble with  
the Loudness being  
switched off.  
Try out which SPEECH set-  
ting you like most.  
LED ON  
Here you can choose be-  
tween LED ON or LED OFF.  
With LED ON, the KeyCard  
tongue will flash for extra  
anti-theft protection when  
the unit has been switched  
off and the KeyCard re-  
moved.  
BEEP  
Acknowledgement tone for  
all functions which require a  
button to be pressed for  
more than one second.  
The volume can be adjusted  
from between 0 to 9. (0 =  
off).  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
PTY LANG To select the programme  
type language:  
VOL FIX  
Use this function to select  
the volume at which the ra-  
dio is set when it is switched  
on. Adjust the desired vol-  
ume level with << >>. When  
adjusted to “VOL 0”, the  
system will come on with the  
volume selected before  
Specifications  
Amplifier  
DEUTSCH or ENGLISH  
Output power:  
4 x 23 W RMS power  
acc. to DIN 45324 at  
14.4 V  
SCANTIME Use this function to set the  
scan time for the radio or  
4 x 35 W max. power  
CD player from between five  
and 30 seconds.  
Tuner  
Wavebands:  
switching the radio off.  
FM  
MW  
LW  
:
:
:
87.5 – 108 MHz  
531 – 1602 kHz  
153 – 279 kHz  
S-DX  
S-LO  
To adjust the seek tuning  
sensitivity for distant recep-  
tion.  
DX 1 - high sensitivity  
DX 3 - low sensitivity  
To quit the DSC programming mode  
and store the adjustment:  
Press DSC.  
FM sensitivity:  
0.9 µV at 26 dB signal-  
to-noise ratio  
Overview of the DSC factory  
settings  
FM frequency response:  
30 - 16 000 Hz  
To adjust the seek tuning  
sensitivity for local recep-  
tion.  
LO 1 - high sensitivity  
LO 3 - low sensitivity  
The seek tuning sensitivity  
values can be separately set  
for AM and FM.  
LOUDNESS  
TA VOL  
SPEECH  
BEEP  
3
35  
0
4
CD player  
Frequency response:  
ANGLE  
0
20 - 20 000 Hz  
BRIGHT  
LED  
16  
ON  
LEARN KC  
READ KC  
PTY LANG  
SCANTIME  
S - DX  
-
-
ENGLISH  
10 sec.  
1
1
0
S - LO  
VOL FIX  
Subject to modifications!  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Blaupunkt  
telephone hotline  
Address of the next service  
centre in your vicinity  
(only for Germany)  
If you would like to know the address of  
the next Blaupunkt service centre of  
your area without having our service list  
at hand:  
-
-
Find out your area code.  
Then call the following chargeable  
phone number: 01 80 / 5 25 56 66.  
-
Using the area code to be entered  
you will be automatically given the  
address and phone number of the  
next Blaupunkt service centre. You  
can also request this information  
by fax.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Blaupunkt-Werke GmbH  
Bosch Gruppe  
5/96 Pf  
K7/VKD 8 622 400 773  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Decker Trimmer 616080 00 User Manual
Bogen Speaker System FH 2 User Manual
Bosch Power Tools Cordless Drill CLPK232 180 User Manual
Bose CD Player SM1 User Manual
Boss Audio Systems Speaker MR100 User Manual
Bostitch Automobile Parts GT18B01 User Manual
Brother Pet Fence Z 8550A User Manual
Calphalon Waffle Iron HE500RW User Manual
Cecilware Coffeemaker VAE J1 User Manual
Chauvet Indoor Furnishings CH 444A User Manual