Radio / Cassette
Casablanca
RCM 85
Operating instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Short instructions ........................ 20 Recalling stored stations ....................... 28 DSC programming........................ 32
Scanning stored stations with
Overview of the DSC factory settings ... 33
Important notes ............................ 23
Preset Scan .......................................... 28
Scanning stations with Radio-Scan ...... 28
Selecting the seek tuning sensitivity ..... 28
Switching from stereo to mono (FM) ..... 29
CD changer control (optional)..... 34
Precautions ........................................... 23
Traffic safety ......................................... 23
Installation/Connection.......................... 24
Switching to changer operation
with SRC on the car radio ..................... 34
Selecting a disc/track using the
rocker switch ......................................... 34
SCAN .................................................... 34
MIX ........................................................ 34
Receiving traffic programme
stations with RDS-EON ................ 29
KeyCard theft-protection
system ........................................... 24
Traffic announcement priority on/off ..... 29
Warning beep........................................ 29
Switching the warning beep off.......... 29
Automatic seek tuning start................... 30
Adjusting the volume for traffic
Putting the unit into operation ............... 24
Removing the KeyCard ......................... 24
“Defining” a second KeyCard/
Replacing a KeyCard ............................ 24
Displaying the radio pass data .............. 25
Optical indication for extra security ....... 25
Appendix ....................................... 35
Specifications ........................................ 35
announcements and the warning beep . 30
Tape operation.............................. 30
Radio operation with RDS ........... 26
Inserting a tape ..................................... 30
Removing a tape ................................... 30
Fast Forward/Rewind ............................ 30
PROG selector
To change the tape direction during
cassette playback ................................. 30
Dolby B-NR* and
tape equalisation with B/MTL ................ 31
Skipping/repeating titles with CPS ........ 31
Switching the audio source with SRC ... 31
Tape care .............................................. 32
AF - Alternative frequency .................... 26
REG - regional programme ................... 26
Selecting a waveband ........................... 26
Automatic tuning ................................ 26
Manual tuning .................................... 27
Scrolling through the broadcasting
network (only FM) ................................. 27
Changing the memory bank (FM) ......... 27
Storing stations ..................................... 27
Automatically storing the strongest
stations with Travelstore ....................... 28
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Short instructions
1 On
Volume
Off
2 LD
Loudness - When listening at a low
level, the Loudness function creates a
more natural sound by boosting the low
frequency range.
To switch the Loudness on/off:
Press LD.
Fader front
Fader rear
For more information, read chapter
“DSC programming”.
Balance left
Balance right
This unit can also be switched on and
off with the KeyCard C.
Also, when being connected correctly,
you may turn the radio on and off via
the ignition of your car.
Use one of the following possibilities to
continue operating the set when the
ignition is switched off:
a) Switch on/off with knob 1.
b) Remove/insert the KeyCard.
c) Press AUD 3.
When turning on the unit with the Key-
Card or by pressing the AUD button,
the system will start to play with the
volume adjusted last.
To alter a setting,
3 AUD/GEO
•
press AUD or GEO and then chan-
AUD –
ge the value with the rocker switch.
The adjusted value is indicated in the
display.
The last setting will be stored automati-
cally.
To finish the setting: Press AUD or
GEO.
If the setting remains unchanged within
8 seconds, the display will switch back
to the previous condition.
To adjust the treble and bass frequen-
cies with the rocker switch.
Treble +
Treble –
Bass –
When operating the unit with the igniti-
on being switched off, the system will
automatically shut down after one hour
in order to avoid that the battery goes
flat.
Bass +
4 DSC (Direct Software Control)
Use the DSC function to customise
certain programmable, basic settings to
suit your personal needs and prefe-
rences. See chapter “DSC pro-
GEO –
To adjust the balance (left/right) and
fader (front/rear) with the rocker switch.
gramming” for more information.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
5 AF - Alternative frequency during RDS
operation
7 B/MTL
Dolby B-NR*
Repeat titles: Press FR.
Skip titles: Press FF.
When “AF” lights up in the display, the
radio will automatically search for a
frequency offering better reception of
the same RDS programme.
Press this button to play back a tape
which has been recorded with Dolby-B.
When this button is pressed, “B” lights
up in the display.
Noise Reduction system manufactured under
license from Dolby Laboratories Licensing
Corporation. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories Licensing
Corporation.
9 Cassette removal
Press
.
*
To switch AF on/off: Press AF briefly.
: Cassette loading slot
Insert tape (side A or 1 up; the open
side facing to the right).
Extra function:
REG ON / REG OFF - With REG ON
the system will only switch to a better
alternative frequency if the latter be-
longs to a linked station offering the
same regional programme (see “REG -
regional programme).
MTL
; Display
Press when using metal or CrO2 tapes.
“MTL” lights up in the display.
Radio operation:
To switch REG on or off: Press AF until
“REG ON” or “REG OFF” appears in
the display (BEEP tone).
NDR1 NDS - Station abbreviation or
frequency
To switch the functions on or off:
Press the B/MTL button during tape
operation until the desired condition is
displayed.
FM
T
5
- Waveband
6 lo
- Memory bank (I, II, T)
- Preset button (1 - 6)
- Stereo
- Seek tuning sensitivity
- Alternative RDS frequency
- Traffic programme identifier
- Priority for traffic programme
stations
To alter the automatic seek tuning sen-
sitivity.
If lo is displayed, the radio will only pick
up strong, local stations (low sensitivi-
ty).
If lo does not light up, the radio will also
pick up weaker, distant stations (high
sensitivity).
To switch over: Press lo briefly.
For more information, see chapter
“DSC programming”.
lo
AF
TP
TA
8 CPS
To repeat or skip cassette titles.
To switch the function on or off: Press
CPS during tape operation.
The display shows the adjusted conditi-
on (“CPS ON/OFF”) each time the but-
ton is pressed.
LD
- Loudness
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Tape operation:
= SC/MIX
Radio operation
@ TA (priority for traffic announcements)
If “TA” is displayed, the system will play
traffic stations only.
Scan (sampling all stations to be recei-
ved): Press SC/MIX briefly.
TA on/off: Press button.
TR1--PLAY - Side 1 (or 2)
Preset Scan (sampling all stations
stored on the preset buttons): Press
SC/MIX for approximately 2 seconds.
A M•L
MTL
B
- Metal
- Dolby B-NR
To select the MW or LW waveband.
Press button as many times until the
desired band is adjusted.
CD changer operation (optional):
Changer operation (optional)
See chapter “CD changer control”.
B FMT - FM, Travelstore
To switch between the FM memory
banks I, II and “T” (Travelstore).
To switch over:
> SRC (Source)
CD 05
T 02
- Disc number
- Title number
To switch between the available audio
sources, e.g. tape, radio, CD changer
(optional).
Press FMT as many times until the
desired bank is indicated in the display.
To store the six most powerful stations
automatically with Travelstore:
Store: Press FMT; seek tuning starts.
Recall: Press FMT as many times until
the display shows “T”. Then briefly
press one of the preset buttons 1, 2, 3,
4, 5, or 6.
< Fast winding/PROG button
? 1, 2, 3, 4, 5, 6 - preset buttons
You can store six stations on each FM
memory bank (I, II, T).
To switch to the other side of the
cassette tape:
Press both buttons simultaneously.
The display shows TR1-PLAY or TR2-PLAY.
To store a station: Press button during
radio operation and hold down until the
radio resumes play.
To recall a station: Select the wave-
band and on FM also the desired me-
mory bank (press FMT button as many
times as required). Then press the cor-
responding preset button briefly.
FR : Fast rewind; stop by pressing FF.
FF : Fast forward; stop by pressing FR.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Important notes
Precautions
C KeyCard theft-protection system
To operate the set it is necessary that
you have inserted the KeyCard.
D Rocker switch
Seek tuning
Before starting to use your new car radio,
please read the information on “Traffic safe-
ty” and “KeyCard theft-protection system”
carefully.
KeyCard
Traffic safety
Up
Down
For this, introduce the KeyCard into the
slot with the contact area showing up
(KeyCard tongue pulled out).
Read also the information under “Key-
Card”.
As the driver of a motor vehicle, it is your
responsibility to pay attention to the traffic
situationatalltimes.Neveruseyourcarradio
in a way that could distract you.
Please keep in mind that you travel a di-
stance of 14 m per second at a speed of only
50 km/h.
Should the traffic situation become particu-
larlydemanding,weadviseyounottousethe
radio.
Always make sure that you are still able to
hear any warning signals coming from outsi-
deofthevehicle, suchaspoliceorfireengine
sirens, so that you can react accordingly.
Therefore, youshouldalwaysselectamode-
rate volume for playing your car radio while
you are driving.
/
/
Up/down in short intervals
(“AF” must be switched off)
To scroll through the broadcasting
network when “AF” is activated
(e.g. NDR1 ... NDR4).
Flashing KeyCard tongue
When the car radio is turned off, the
KeyCard tongue can be switched to
flash for extra anti-theft protection. This
feature can be switched on and off via
DSC - CODE-LED.
Extra functions:
In the DSC mode:
Select and programme
DSC functions.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
KeyCard theft-protection system
This car radio is supplied with one KeyCard After approximately 10 seconds, the display
as standard.
However, the unit can also be operated with When inserting a card of a different kind (like
a second card. for example a phone or credit card), the
If you have lost or damaged your KeyCard, display will show “WRONG KC” for approxi-
you can buy a new one from your specialised mately 2 seconds.
will show “TURN OFF”. Now turn off the set.
blan-
Installation/Connection
If you would like to install this equipment
yourself or add any new components, please
read the enclosed installation and connec-
tion instructions carefully.
Do not connect the loudspeaker outputs to
ground!
dealer.
Remove the wrong card and turn off the set.
When using two KeyCards, you can indivi- Do not make further adjustments until you
dually store the following functions:
have a correct KeyCard available.
Use only the accessory and replacement
parts approved by Blaupunkt.
Bass, treble, balance and fader settings,
assignments of preset buttons, Loudness,
TA (traffic announcement volume), BEEP
volume.
Removing the KeyCard
Never pull out the KeyCard directly.
pro-
•
First press the KeyCard in.
In addition to this, the settings activated be-
fore switching the radio off, such as the
waveband, station, TA priority, Loudness,
AF, REG ON/OFF and seek tuning sensitivi-
ty, will also remained stored.
This releases the card and puts it in the
proper position for being removed.
s ne-
e in-
•
Now you can pull it out.
Thisensuresthatthebasicsettingsyouhave
programmed will automatically be activated
as soon as you have inserted your KeyCard.
“Defining” a second KeyCard/
Replacing a KeyCard
e
with
wing
pul-
While operating the unit with the first Key-
Card, you can “define” a second one to be
also used with the set:
Putting the unit into operation
•
Turn on the set and introduce the Key-
Card into the slot with the contact area
showing up (KeyCard tongue pulled
out).
•
Insert the first KeyCard and turn on the
set.
ation
•
Press the DSC button and select
“LEARN KC” with / .
The car radio is now ready for operation.
If a wrong KeyCard is inserted, then “CARD
ERR” will appear in the display. In this case
please do not go on operating the set.
The display will switch to “CHANGE”.
on-
tur-
24
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Press the KeyCard in, which releases
the card and puts it in the proper positi- security
on for being removed.
Optical indication for extra
When the car is stationary, the KeyCard
tonguecanbeswitchedtoflashforextraanti-
theft security.
For this, the following requirements must be
fulfilled:
Permanent 12 V supply and the + ignition
lead must be connected correctly (as illustra-
ted in the installations instructions).
“LED 1” must be adjusted in the DSC mode.
Please refer to chapter “DSC programming -
LED”.
Remove the first KeyCard and insert
the new one while “CHANGE” is still
being displayed.
Now you can also use the new KeyCard for
operating your unit.
Amaximumoftwocardscanbeusedperset.
When trying to “define” a third one, the
system will automatically delete the access
authorisation of that KeyCard which was not
used for the “learning” process.
Displaying the radio pass data
You can use the KeyCard 1 supplied with the
unit to display the individual radio pass data
such as the model name, the type number
(7 6 ...) and the serial number:
•
Press and hold down preset buttons 1
and 6 while switching on the unit.
•
Press the M•L button within 2 seconds.
The radio pass data will move through the
display several times.
To quit the function:
•
Press any button.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio operation with RDS (Radio Data System)
The Radio Data System offers you more If “SEARCH” appears in the display when If you leave the service area of the regional
convenience when listening to FM radio sta- switching on the radio or recalling one of the programme tuned into, or if you would like to
tions.
stored frequencies, the unit is automatically takeadvantageofthefullRDSservice,switch
More and more radio stations have begun to searching for an alternative frequency.
broadcast RDS information alongside their “SEARCH” will disappear from the display
to “REG OFF”.
•
Press the AF button for approximately
programmes.
Assoonasaprogrammehasbeenidentified, found or after the frequency band has been
when the alternative frequency has been
2 seconds until “REG OFF” appears.
When active, “REG ON” will be briefly dis-
played each time the radio is switched on.
run through completely.
the station name including a regional identi-
fier, if applicable, will appear in the display,
If the reception quality of the selected pro-
for example, NDR1 NDS (regional program- gramme becomes too bad:
Selecting a waveband
me in Lower Saxony, Germany).
•
Tune into another station.
When RDS is activated, the station buttons
become programme buttons. You now know
exactly which programme you have tuned
into, making it easy to find the desired station
quickly.
With this car radio you can select between
the following wavebands:
FM 87.5 - 108 MHz
REG - regional programme
Certain radio programmes are split up at MW 531 - 1602 kHz
times into regional programmes offering lo-
cal information. The 1st programme broad-
cast by NDR, for example, offers program-
mes with different contents in the northern
statesofGermanySchleswig-Holstein,Ham-
burg and Lower Saxony at certain times of
the day. If you are listening to one program-
me and move to an area where another
linked regional programme becomes stron-
ger, the unit will switch to that programme.
If you wish to continue listening to the first
programme,
LW 153 - 279 kHz
But RDS offers you further advantages:
•
Select the desired waveband by pres-
sing the FMT or M•L button.
AF - Alternative frequency
To switch between MW and LW:
Press M•L.
•
The AF (Alternative Frequency) function
makes sure that the strongest frequency of
the currently selected programme is always
tuned in automatically.
This function is activated when “AF” appears
in the display.
Automatic tuning
Press / ; the car radio will automati-
cally search for the next station.
Whenkeepingtheupperorlowerpart
/
•
/
of
In order to switch this function on or off,
the rocker switch depressed, seek tuning will
speed up in upwards or downwards direc-
tion.
•
press the AF button briefly.
•
press the AF button for approximately
2 seconds.
While searching for the strongest reception
signal, the radio may switch to mute briefly.
“REG ON” appears in the display.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic tuning
Scrolling through the broad-
•
Press the FMT button as many times
until the desired memory bank lights up
in the display.
casting network (only FM)
You can use the << >> buttons to tune in
stations of your reception area.
Storing stations
If several programmes of one broadcasting
network can be received, you can scroll
through them in forwards direction pressing
>>, or backwards using the << button, e.g.
NDR 1, 2, 3, 4, N-JOY (North German broad-
caster).
For this it is necessary that the stations have
beenreceivedatleastonceandthat“AF”has
been activated before (lights up in the dis-
play).
On FM, you can store six stations on the
preset buttons 1 to 6 for each of the memory
banks I, II and T.
Up
Down
/
/
Up/down in short intervals
On MW/LW, you can store six stations each.
(“AF” must be switched off)
To scroll through the broadcasting
network when “AF” is activated
(e.g. NDR1 ... NDR4).
•
Select the waveband with FMT or M•L
and on FM also the desired memory
bank (with FMT).
•
•
Tune in a station with the rocker switch
(either automatically or manually).
Manual tuning << >>
(prerequisite: AF is switched off!)
For this purpose, you may start Travelstore
seek operation:
Press the desired preset button until
the radio resumes play after the muting
(takes approximately 2 seconds, confir-
med by beep).
•
Press << >>; the frequency will change
in short intervals in downwards or up-
wards direction.
•
Press FMT for 2 seconds; the system
starts to run through the frequency
band.
When holding the right or left part of the
rocker switch pressed down, the frequency
scan is speeded up.
Now the station has been stored.
Theactivatedpresetbuttonisindicatedinthe
display.
If “AF” does not light up,
press AF.
•
With this, the requirements for selecting sta-
tions with << >> are fulfilled.
Notice:
Should you tune in a station which has alrea-
dy been stored before, the corresponding
presetbuttonandthememorybankwillbriefly
flash in the display if you have selected
another memory bank.
Changing the memory bank (FM)
You can shift between the memory banks I, II
and T in order to store stations and recall
them later.
The currently selected memory bank is indi-
cated in the display.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatically storing the stron-
gest stations with Travelstore
Scanning stored stations
with Preset Scan
To start the scan:
•
Press SC/MIX briefly.
The scanned frequency or the station
name will start flashing in the display.
During the actual scanning process
“SCAN” will be displayed.
You can automatically store the six most Youcanhaveallofthestoredstationsplayed
powerful FM stations of your current recepti- briefly on all wavebands.
on area sorted according to their signal On FM, you can scan the stations of the
strength. This function is particularly conve- Travelstore memory bank or of the two other
To select a station currently being scan-
ned and switch off the scan function:
nient on longer trips.
storage levels.
•
Press the FMT button for more than
2 seconds.
•
•
Select the waveband.
•
Press SC/MIX briefly.
On FM, choose Travelstore or another
If no station is selected, the scan function will
be automatically switched off after the fre-
quency band has been run through comple-
tely. The unit will tune in the station listened
to before starting the scan.
The radio will search for the strongest FM
stations and store them on the memory bank
T (Travelstore). When this process has been
completed, the radio will play the first station.
If desired, stations can also be stored manu-
ally on the Travelstore bank (see “Storing
stations”).
memory bank using the FMT button.
To start Preset Scan:
•
Press SC/MIX for approximately 2 se-
conds.
The stations will be played for approximately
8 seconds each.
Selecting the seek tuning sensi-
tivity
The positions blinking in the display show
you the memory bank and preset position of
the currently scanned station.
You can alter the automatic seek tuning
sensitivity.
Recalling stored stations
You can recall any stored station at the touch
of a button.
To select a station currently being
scanned and switch off Preset Scan:
If “lo” is displayed, the radio will only pick up
strong, local stations (low sensitivity).
If “lo” does not light up, the radio will also pick
up weaker, distant stations (high sensitivity).
To switch over,
•
Select the waveband by pressing FMT
or M•L. On FM, also choose the corre-
sponding memory bank by pressing the
FMT button as many times until the
desired bank appears in the display.
•
Press SC/MIX briefly.
Scanning stations with
Radio-Scan
•
Press lo.
The degree of sensitivity can be altered in
both modes (see also chapter “DSC pro-
gramming”).
Beginning with the station currently tuned in,
you can scan the waveband. The radio will
play each station for 8 seconds.
•
Press the corresponding preset button
briefly to recall the station.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving traffic programme stations with RDS-EON
Switching from stereo to mono
(FM)
Many FM broadcasters offer traffic messa- When pressing TA while a message is being
ges for their service area at regular intervals. broadcast, this message will be interrupted.
All traffic programme stations transmit a spe- The unit will then switch back to the previous
cial carrier signal alongside their program- condition. The priority for other traffic messa-
If reception is poor, you may get better sound
quality by switching to mono:
ges remains active.
mes, which is decoded by your car radio. If
this signal is identified, “TP” will appear in the
display (Traffic Programme).
•
Press the lo button for approximately
2 seconds.
Warning beep
With mono playback, the stereo sign
will disappear from the display.
In addition to these, there are also stations
which do not actually transmit traffic pro-
grammes themselves, but by using RDS-
EON they offer the possibility to receive the
traffic messages broadcast by another traffic
programme station in the same radio net-
work. If you listen to one of these stations
(e.g. NDR3), “TP” will appear in the display
provided the priority for traffic programme
stationshasbeenactivated, i.e. “TA”mustbe
displayed.
If a traffic announcement is broadcast, the
radio will automatically switch to the linked
trafficprogrammestation(inthiscase,NDR2)
for the duration of the message and return to
the original programme (NDR3) afterwards.
If you leave the reception area of the traffic
programme station currently tuned into, you
will hear a warning beep after approximately
30 seconds.
This alarm tone will also be released when
pressing a preset button which has no traffic
programme allocated to it.
Each time the radio is switched on, stereo
playback is activated.
The unit will automatically switch to mono if
the received signal is not strong enough for
stereo playback.
Switching the warning beep off
a) Tune into another station offering traffic
information:
•
•
Press the rocker switch or
a preset button which has a traffic
programme station allocated to it.
Alternatively:
b) Switch off the priority for traffic an-
nouncements:
Traffic announcement priority
on/off
•
Press TA.
If the priority for traffic announcement pro-
grammes is activated, “TA” will light up in the
display.
“TA” will disappear from the display.
To switch the priority on or off:
•
Press the TA button.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Tape operation
Inserting a tape
Automatic seek tuning start
Fast Rewind
(tape operation)
•
Press FR.
•
•
Turn on the set.
Insert a tape.
At the beginning of the tape, the me-
chanism will automatically start play-
back.
When leaving the reception area of the tuned
in traffic programme station while listening to
a tape, the system will automatically start
searching for a new TA programme.
If no such station is found within approxima-
tely 30 seconds, tape operation will be stop-
ped and a warning beep will sound.
To switch the warning beep off, proceed as
described above.
Insert the tape with side A or 1 showing up, the
open side facing to the right.
Stopping Fast Rewind operation
•
Press FF.
To switch to the other tape side:
Press simultaneously.
TR1-PLAY or TR2-PLAY shown in the
display.
= Press to eject the tape.
The tape will be played in the direction used
last.
“TR1-PLAY” in the display means that track
1 or A is being played.
Adjusting the volume for traffic
announcements and the warning
beep
This volume was preset at the factory.
YoucanalterthevalueusingtheDSCfunction
(see “DSC programming, TA”).
Removing a tape
FR : Fast rewind; stop by pressing FF.
FF : Fast forward; stop by pressing FR.
•
Press
.
The cassette will eject.
PROG selector
To change the tape direction during
cassette playback
Fast Forward/Rewind
Fast Forward
•
Press FR and FF simultaneously.
•
Press FF.
At the end of a tape side, the mechanism
changes directions automatically to play the
other side (Autoreverse). The display shows
“TR1-PLAY” for track (side) 1 or A or “TR2-
PLAY” for track 2 or B.
At the end of a tape side, the mecha-
nism changes directions automatically
to play the other side.
Stopping Fast Forward operation
Press FR.
•
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice:
MTL
“CPS ON” or “CPS OFF” will light up in the
display for approximately 2 seconds.
Ifthereistoomuchtensiononthetapeduring
playback, the set may switch over by itself
before having reached the end of the tape
side. In this case check the condition of the
cassette tape. Sometimes it helps to rewind
it completely.
Switch on the MTL function to select the best
equalisation response when using metal or
CrO2 tapes. “MTL” will light up in the display.
With “CPS ON”:
Fully depress the FF button -
The tape is fast forwarded to the next title.
To switch Dolby B-NR and MTL on/off:
•
Press B/MTL repeatedly until the desi-
red setting appears in the display.
Dolby B-NR* and
tape equalisation with B/MTL
Fully depress the FR button -
The tape is rewound to the beginning of the
current title, provided that it has already been
played for more than 8 seconds. Otherwise the
tape will be rewound to the beginning of the
previous title.
Dolby B-NR*
With this unit you can play back tapes recor-
ded with Dolby-B or without noise reduction.
Cassette tapes recorded with Dolby NR*
stand out by their much lower tape hiss and
the improved dynamics.
The system enables the following settings:
MTL tape The display shows
with Dolby B-NR
without Dolby B-NR
Normal tape
MTL
MTL
B
–
Switching the audio source
with SRC (Source)
If Dolby B-NR is switched on, “B” will light up
in the display.
*
Noise Reduction system manufactured under license
from Dolby Laboratories Licensing Corporation. “Dol-
by” and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
Using this function you can switch between
radio, tapeandCDchanger(optional)opera-
tion or playback of any other connected de-
vice.
with Dolby B-NR
without Dolby B-NR
–
–
B
–
Skipping/repeating titles
with CPS
To switch over:
•
Press the SRC button.
CPS stands for Cassette Program Search.
This function allows you to skip a cassette
title or listen to it once again.
To switch the function on/off:
•
Press CPS.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
DSC programming
DSC (Direct Software Control) allows you to
customise certain programmable, basic set-
tings to suit your personal needs and prefe-
rences and then store them.
The basic settings for this audio equipment
weremadeatthefactory. Inthefollowingyou
canfindanoverviewofthesesettings,sothat
you can always reset to these if desired.
If you wish to alter any of the programming,
Tape care
DIS
(dx)
To adjust the seek tuning
sensitivity for distant recep-
tion.
DIS. 1 - high sensitivity
DIS. 3 - low sensitivity
To avoid possible problems, you should not
use cassette tapes longer than 60 or 90
minutes (C60/C90). Store your tapes in a
cool place away from dirt, dust and tempera-
turesexceeding50° Celsius. Allowverycold
tapes to warm up before playing them in
order to avoid uneven tape transport. After
approximately 100 hours of use, dust partic-
les collected on the playback head or roller
may lead to tape run problems and sound
distortions.
Use a head cleaning tape to remove normal
dirt build-up. For tougher cases, use a cotton
swab (Q-Tip) soaked with alcohol. Do not
attempt to clean by inserting a hard object
into the player!
TIME ON/OFF To select the display mode
during CD changer opera-
tion (option).
•
press DSC.
The display will show the function adjusted
last.
Usetherockerswitchtoselectandadjustthe
functions described in the following.
TIME ON - display of title
and playback time.
TIME OFF - display of CD
and title number.
If SCAN or MIX is active,
the system will always
switch to the TIME OFF
mode.
LEARN KC
TA VOL
To “define” a second Key-
Card for use with the set.
Please read the information
under “KeyCard theft-pro-
tection system”.
/
Select function
Adjust value –
Adjust value +
LOCAL
(lo)
To adjust the seek tuning
sensitivity for local recepti-
on.
To adjust the traffic an-
nouncement volume from
between 1 to 9. The mes-
sage will then come
through at this volume.
(1 = low)
LOCAL 1 - high sensitivity
LOCAL 3 - low sensitivity
32
Download from Www.Somanuals.com. All Manuals Search And Download.
BEEP
Confirmation tone for all
functions which require a
button to be pressed for
more than 2 seconds.
The volume can be adju-
sted from between 0 to 9.
(0 = off)
Each alteration of this va-
lue is confirmed by a beep
tone of the corresponding
volume.
LOUD
Loudness - When listening Overview of the DSC factory
at a low level, the Loud-
ness function creates a
more natural sound by
boosting the low frequency
range.
settings
LOCAL
DIS
: 1
: 1
TIME
: OFF
: 4
TA VOL
BEEP
LED (Code) : 1
LOUD 1 - Low boost
LOUD 6 - Max. boost
: 3
LOUD
RM
: 4
: OFF
RM
(Radio Monitor)
With RM-ON, the unit will
automatically switch to the
tuner whenever the casset-
te is fast winding.
RM-OFF - The function is
switched off.
LED (code)
You can adjust the LED C
to flash for extra anti-theft
protection.
LED 1 - LED always flas-
hes when the unit
has been swit-
ched off via the
ignition and the
KeyCard remo-
ved.
To quit the DSC programming mode and
store the adjustment:
•
Press DSC.
If the setting remains unchanged within 8
seconds, the system will automatically store
the last adjustment. The display will switch
back to the previous condition.
LED 0 - No flashing.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
CD changer control (optional)
You can operate the Blaupunkt CD changer Selecting a disc/track using the
CDC-A05 in combination with this car radio. rocker switch
To stop the SCAN:
•
Press the SC/MIX button briefly once
again. The system will continue to play
the currently scanned track.
Switching to changer operation
with SRC on the car radio
MIX
Make sure that a magazine is inserted.
Press SRC to switch between the different
audio sources (radio - changer - tape).
Use the MIX function to play the tracks of the
individual discs in random order. Note that
the discs themselves will be selected in nu-
meric order according to their position in the
changer.
Press SRC as many times until the changer
functions appear in the display.
Select track (upwards): Press briefly.
CUE - fast advance (audible):
Press and hold down.
Repeat track: Press briefly.
Select track (downwards): Press repeated-
ly.
REVIEW - fast reverse (audible):
Press and hold down.
To start the MIX function:
•
Press the SC/MIX button for approxi-
mately 4 seconds. The CD number and
‘MIX’ will appear in the display.
To stop the MIX function:
Press SC/MIX briefly.
Select disc (downwards)
Select disc (upwards)
•
CD = disc, T = TRACK (title).
Notice:
The display shows you the selected mode.
0:24 = playback time of the current title
In may happen in isolated cases that the
changerfailstofunctionproperlyduetovolta-
ge drops (e.g. when starting the engine). In
such a case, briefly switch the car radio off
and on again.
SCAN
Use this function to scan the CD tracks.
To start the SCAN:
Thechangerwillthenreturntonormalopera-
tion.
•
Press the SC/MIX button briefly. The
tracks will be played briefly one after
the other in ascending order. The num-
ber of the currently scanned track flash-
es in the display.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Specifications
Amplifier
Output power:
4 x 19 W RMS power
acc. to DIN 45324/3.1
or
4 x 20 W max. power
acc. to DIN 45324/3.2
Tuner
Wavebands
FM
MW
LW
:
:
:
87.5 – 108 MHz
531 – 1602 kHz
153 – 279 kHz
FM sensitivity:
1.0 µV at 26 dB
signal-to-noise ratio
FM frequency
response:
35 - 16 000 Hz
35 - 16 000 Hz
Tape player
Frequency
response:
Subject to modifications!
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Blaupunkt-Werke GmbH
Bosch Gruppe
2/96 Pf
K7/VKD 8 622 400 491
Download from Www.Somanuals.com. All Manuals Search And Download.
|