Blaupunkt Car Stereo System CR 87 User Manual

Radio / Cassette  
Santiago CR 87  
Operating instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features  
Radio Features  
- 15 FM/5 AM Presets, Including 5 FM and 5 AM Travelstore Presets  
- Station Scan  
- Local/Distant Seek and Manual Tuning  
Cassette Tape Player Features  
- Auto-Reverse Cassette Mechanism  
- True Fast-Forward/Rewind  
- Radio Monitor  
- Dolby B NR  
Audio Features:  
- 20 Watts x 4 Channel Integrated Amplifier  
- 2-Channel Preamp Output  
- Adjustable Maximum Turn-On Volume  
- Bass, Treble, Balance and Fader Control  
- Loudness Button  
- Mute Button  
- Auxiliary Input  
Other Features:  
- Detachable Face (Release Panel)  
- Illumination, Amber  
- Clock Recall  
- 179 x 50 x 150 mm DIN/ISO Chassis  
- Detachable Wire Harness  
- Snap-In DIN Sleeve and Mounting Hardware  
Your unit’s detachable front faceplate makes the unit useless to would-be thieves.  
Designed, Engineered and Manufactured By Blaupunkt.  
Traffic Safety and Precautions  
Do not adjust your unit in difficult driving conditions that demand your full attention.  
As the driver of a motor vehicle, it is your responsibility to pay attention to the traffic situation  
at all times. Never use your unit in a way that could distract you.  
Always make sure that you are still able to hear any warning signals coming from outside of  
the vehicle, such as police or fire engine sirens, so that you can react accordingly.  
If your vehicle was parked in direct sunlight resulting in a considerable rise in temperature  
inside the vehicle, allow the unit to cool off before operating it.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Detachable Face (Release Panel)  
Detaching and Attaching the Face:  
The face of this unit can be detached and taken with you to prevent it from being stolen.  
Detaching the Face:  
Press the REL (Release) Button and detach the face by gently pulling it off as illustrated.  
Note: Do not pull it straight out from the chassis. Be sure not to drop the face when detaching it  
from the chassis. Do not expose the face to direct sunlight, heat sources such as hot air ducts or  
leave it in a humid place.  
Attaching the Face:  
Apply the right hand side of the face to the chassis by sliding (part B) of the face to (part A) at  
the front of the chassis. Gently push the left side of the face against the front of the chassis until  
it snaps into place.  
Note: Do not press against the display window. Do not press hard against the face when  
attaching it to the chassis, it may be easily attached with gentle pressure.  
Affixing Faceplate For Retail Display:  
The faceplate can be affixed to the unit’s chassis, which is desirable for a retail display, for  
example.  
To affix the faceplate:  
Insert the black bolt into the hole at the left front of the top of the radio. See * below.  
*
A
B
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electrical Connections  
To avoid the aggravation of costly mistakes and serious damage, please carefully read all of the  
instructions before you begin. Carefully follow all instructions.  
General Recommendations  
If you’re not confident that you can install the unit correctly, have it installed by a qualified  
Blaupunkt installation technician.  
Use this unit only with negative ground 12 Volt (11-16 Volt) direct current (DC).  
Be sure to detach the faceplate before you start to connect or install the unit.  
We recommend making and testing all electrical connections before installing the unit.  
Connect the leads (wires) according to instructions and diagram below.  
Electrical Connection Instructions  
1. Disconnect the vehicle battery’s negative terminal before making connections.  
2. Connect the speakers following the guidelines in the “Speaker Connection” section below.  
3. Connect the antenna output lead to the antenna motor trigger input terminal (if you have  
one). The total amperage required of the antenna lead must not exceed 100 mA. Do not  
connect the antenna lead to the antenna’s power supply input.  
4. Connect the ground lead to a grounded metal part on the vehicle. We recommend  
grounding all audio system ground leads (head unit, external amplifier, etc.) to a common  
grounding point, preferably a non-painted surface under the instrument panel.  
5. Connect the battery input lead to a source of constant battery power, preferably a terminal  
to an appropriate slot in the fuse box.  
6. Connect the ignition input lead only after the other leads are connected. Be sure to connect  
the ignition lead to a positive (+) 12 Volt power terminal that is energized only when the  
ignition key is set to the on position or accessory position.  
7. Cover the ends of any unused leads with electrical tape. This will prevent them from  
touching the vehicle or each other and causing a short-circuit and damage to the radio or  
vehicle.  
8. Reconnect the vehicle’s battery.  
9. Verify that no fuses have blown.  
10. Plug the harness into the unit.  
Electrical Connections  
Ignition  
+12V  
Antenna  
Ground –  
+12V  
Battery  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker Connections  
Speaker Connections  
R
L
LF  
F
R
R
R
+
-
+
-
+
-
+
-
RF  
LF  
RR  
LR  
Attach the faceplate and test the unit.  
Once the connections have been successfully made, you can begin to mount the unit.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Recommendations  
The illustration below shows a typical installation, however, you may need to adjust the  
installation, depending on the unit. If you have questions or need additional installation  
hardware, consult your Blaupunkt dealer.  
Make sure the unit is firmly anchored and does not vibrate.  
Mounting Hardware  
Release Keys  
Sleeve  
Mounting The Unit in Most Dashboards  
1. Install the Sleeve in the dashboard.  
2. Select and bend the appropriate tabs to hold the sleeve firmly in place.  
Bend these tabs  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting the Unit in a Japanese Car  
You may have difficulty mounting this unit in some Japanese cars that have ISO mounting  
features. In this case, consult your Blaupunkt dealer.  
1. Run a blade along the slits on the back of the front trim ring, unscrew the two side screws,  
and separate it from the unit. Save the trim ring and related hardware in case you ever want  
to install the unit in another vehicle.  
2. Use the vehicle’s own mounting hardware to attach the unit.  
2 TOYOTA  
1
max. size M5x8  
Slit  
to dashboard/center console  
max. size  
M5x8  
Bracket  
Support  
2 NISSAN  
max. size M5x8  
to dashboard/center console  
max. size  
M5x8  
Bracket  
Support  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
Removing the Unit  
Use the Release Keys as shown below. Keep them in a safe place in case you need them in the  
future.  
Fuse Replacement  
When replacing the fuse, be sure to use one with the correct amperage, which will be stated on  
the fuse case. Never use a fuse that has a stated amperage exceeding the one supplied for this  
unit, as this could cause malfunction and serious damage to the unit.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Location of Controls  
1
2
3
4
5
REL (Release) – Detaching Faceplate  
ON (Power)  
– Power On/Off  
– Source and Radio Band Select  
– Cassette Eject  
– Mute  
SRC  
AUDIO  
SCA  
TS  
– Audio  
6
7
– Scan  
– Travelstore  
LD  
– Loudness  
SENS  
– Tuning Sensitivity  
8
9
Cassette Insertion Slot  
CLK  
– Clock Recall  
DISP  
– Display Change  
10/11 PROG  
– Tape Program Change (reverse)  
– Fast Rewind  
10  
11  
12  
13  
14  
15  
16  
17  
18  
FR  
FF  
+
– Fast Forward  
– Volume + / Bass + / Treble + / Balance Left / Fade to Front  
– Volume - / Bass - / Treble - / Balance Right / Fade to Rear  
– Seek and Manual Tuning / Clock Hours  
– Seek and Manual Tuning / Clock Minutes  
– FM/AM Presets  
1, 2, 3, 4, 5  
Display  
– Dolby B NR (Noise Reduction)  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instructions – General Operation  
See Traffic Safety and Precautions on page 19.  
“Press” means a momentary press of less than 1/2 second. All presses requiring more than 1/2  
second are followed by beep.  
“Time Out” When additional button presses are anticipated to complete a procedure, the unit will  
automatically exit the procedure after 4 seconds of inactivity.  
Clock Recall  
Vehicle ignition must be on. The display switches to clock.  
Release for Detachable Faceplate  
Push REL to detach face. Already inserted cassette remains in unit. Current settings and source  
mode are stored. If power was not switched off before face removed, unit will automatically  
power-on when face is reattached.  
Power On  
When ignition on, press ON or insert a disc to turn unit on. Last-used source becomes active,  
unless unit is turned on by inserting tape, in which case tape player becomes active.  
Power Off  
Press ON for more than 1/2 second to turn the unit off. Unit stores current settings for source,  
station or track, etc.  
Setting the Clock  
Turn the unit on. Press the CLK Button for four seconds until the clock starts blinking. (The  
display will change after two seconds. Ignore this and continue to hold for two more seconds.)  
Once the clock starts blinking, Press the to set the hour, and press the Button to set the  
minutes. Press the CLK Button again to activate the clock.  
Changing the Information Displayed  
You can temporarily change the information shown in your unit’s display. You can also select  
which information has “display priority” and is shown in the display except for moments when  
adjustments are made.  
To change the display priority, press the DISP Button for two seconds. The display priority  
changes. The display priority choices are clock or radio frequency/“TAPE”.  
To change the display temporarily, press and release the DISP Button to access the desired  
information. After four seconds, the display changes back to the priority information.  
Source  
Use SRC to select source - AMT, FM1, FM2, FMT, cassete (if already inserted) or external unit  
(“InP” display).  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Operation  
Volume Control Buttons  
Press + and to increase/decrease volume from 0 to 63.  
Adjustable Maximum Turn-On Volume  
Press and hold the ON Button for more than two seconds. The unit turns off and the turn-on  
volume level is memorized.  
Mute  
Press  
to temporarily reduce volume. “MUTE” appears. Mute is terminated by pressing any  
button.  
Bass, treble, balance and fader  
Bass  
Hould down the AUDIO Button until “BASS” appears and then press immediately + or to  
increase or decrease bass in intervals between 7 and -7.  
Treble  
Hold down the AUDIO Button until “BASS” appears. Then press AUDIO once again so that  
“TREb” appears. Now press immediately + or – to increase or decrease treble in intervals  
between 7 and -7.  
Balance  
Hold down the AUDIO Button until “BASS” appears. Then press AUDIO twice so that “BAL”  
appears. Now press immediately + or to adjust the left/right volume between 9 (left) and -9  
(right).  
Fader  
Hold down the AUDIO Button until “BASS” appears. Then press AUDIO three times so that  
“FADE” appears. Now press immediately + or - to adjust the front/rear volume between 9  
(front) and -9 (rear).  
Loudness  
Press LD to increase sound of low and high frequencies. “LOUD” icon appears. To cancel,  
press LD again.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Radio Operation  
Selecting Bands  
Press SRC as needed to access FM1, FM2, FM3/FMT, AM/AMT banks.  
Tuning Sensitivity  
Press SENS for more that 2 seconds to switch between lo and dx search sensitivity. In general,  
set SENS to “lo” when in metropolitan areas or where stations tend to be strong and local, and  
to “dx” if in rural areas or where stations tend to be weak and distant.  
Seek Tuning  
Press or to seek next receivable frequency. Tuning stops at frequency that fulfills sensitivity  
requirements predetermined.  
Manual Tuning  
To activate manual tuning press and hold or until you hear a beep. Press or again and  
the frequency will go one channel/step in the direction pressed. Press and hold causes  
continuous manual tuning. The manual tuning mode has to be reactivated after 4 seconds or  
after storing a station on a preset.  
Preset Station Storage  
After tuning to the desired radio station on the desired band, press and hold a Preset Button for  
more than 2 seconds to store the current frequency. Audio is muted during the storage, the  
preset number appears, and a beep acknowledges the storage. The number of the selected  
preset appears in the display.  
Preset Station Selection  
Press desired Preset Button.  
Travelstore  
In any FM Bank, press TS for 2 seconds to activate FM Travelstore. (In AM Bank, press it for 2  
seconds to activate AM Travel Store.) “TS” appears. Beginning at the bottom of the band, TS  
stores five relatively strong stations and returns to preset 1.  
Station Scan Tuning  
Press SCA. Frequency blinks during scanning. Unit stops at receivable stations for 4 seconds.  
Unit continuously scans until user stops scan by pressing SCA.  
Radio Reception Hint  
When listening to weak or distant AM stations, adjusting the Treble to minimum (-7) will reduce  
noise and improve sound.  
Stereo Symbol  
Stereo symbol “ ” turns on if a stereo station with a sufficiently strong signal is received. The  
unit gradually switches between mono to stereo automatically.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cassette Tape Player Operation  
Tape Playback:  
Insert cassette into Cassette Door. (Note: Make sure that the side of the cassette exposed is  
facing right.)  
If ignition switch is already in “on” or accessory position, insertion of cassette will turn unit  
on. If unit already turned on, cassette insertion will override other audio source, such as  
radio. “LOAd” appears for 2 seconds. Cassette play will begin, and the display will indicate  
which tape program is in use, “1” or “2”.  
The tape will continue to play until ejected, SRC button pressed, or unit turned off.  
Ejecting The Tape  
Press the button completely towards the face of the unit. The tape will eject. If uit is turned on,  
“EJ” will appear in the display for 2 seconds and the last-heard radio station will play.  
Tape Program Change  
Automatic Change (Autoreverse): When the end of the tape is reached, the unit will  
automatically reverse direction and play the other side of the tape.  
Manual Change: To manually reverse tape direction, press both PROG (program) Buttons  
(FR and FF) at the same time.  
The change in direction and in tape program will be confirmed in the display (“1” or “2”).  
Fast Winding  
To Fast-Rewind the tape, press the FR Button. Tape rewinds and blinks in the display.  
To Fast-Forward the tape, press the FF Button. Tape fast-forwards and  
display.  
blinks in the  
To stop fast-winding, press the other fast winding button, FR or FF.  
Radio Monitor  
During tape winding, the radio will play the most-recently heard radio frequency. All frequencies  
stored on the current bank of preset stations are accessible during fast winding.  
Dolby B NR*  
With this unit you can play back tapes recorded with Dolby B NR or without noise reduction.  
Cassette tapes recorded with Dolby B NR stand out by their reduced tape hiss and the improved  
dynamics. If Dolby B NR is switched on, “ ” will light up in the display. To switch on/off: Press  
the  
button.  
*
Noise Reduction system manufactured under license from Dolby Laboratories Licensing Corporation.  
Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Auxiliary Input Jack  
(cable connection with ø 3.5 mm pigtail coupler)  
Connect other audio equipment, such as a portable CD or DAT player, through a 3.5 mm pigtail  
connector. Press SRC until “InP” appears. Adjust volume, bass, and treble settings through the  
head unit.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Guide  
General  
Trouble  
Cause/Solution  
No sound.  
• Adjust the volume with the + button.  
• With a two-speaker system set the fader control to the  
center position.  
Radio reception  
Trouble  
Cause/Solution*  
Preset stations are not receivable.  
• The broadcast is too weak.  
Automatic tuning is not possible.  
• The broadcast is too weak. —> Use manual tuning.  
• Not enough broadcast frequencies are receivable.  
Travel Store feature does not complete  
storing of five stations.  
* Also make sure that antenna is connected and extended.  
If the above mentioned solutions do not help to improve the situation, consult your nearest Blaupunkt  
dealer.  
Blaupunkt Telephone Hotline  
Address of the next service centre in your vicinity  
(only for Germany)  
If you would like to know the address of the next Blaupunkt service centre of your area  
without having our service list at hand:  
-
-
-
Find out your area code.  
Then call the following chargeable phone number: 01 80 / 5 25 56 66.  
Using the area code to be entered you will be automatically given the address and  
phone number of the next Blaupunkt service centre. You can also request this informa-  
tion by fax.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Audio Power Specifications  
Power Output and Total Harmonic Distortion: 13 watts per channel minimum continuous  
average output into 4 ohms, 4 channels driven, from 35-15000 Hz.  
Other Specifications  
Tuner  
FM  
Tuning Range:  
87.5 - 108 MHz  
1.0 µV  
65 dB (stereo), 70 dB (mono)  
35-15000 Hz  
FM Mono Sensitivity:  
Signal-to-Noise Ratio:  
Frequency Response:  
AM  
Tuning Range:  
Signal-to-Noise Ratio:  
Frequency Response:  
531 - 1602 kHz  
50 dB  
35-5000 Hz  
Cassette  
Signal-to-Noise Ratio:  
Dolby B NR:  
55 dB  
65 dB  
Tape Wow and Flutter:  
Tape Frequency Response:  
0.3 %  
35-15000 Hz  
Audio  
Speaker Impedance:  
Maximum Amp Power:  
RMS Power:  
4-8 ohms  
4 x 20 watts (at 4 ohms)  
4 x 13 watts (at 4 ohms)  
acc. to DIN 45 325 at 14.4 volts  
± 10 dB at 100 Hz  
± 10 dB at 10 kHz  
+ 8 dB at 60 Hz  
Bass Control:  
Treble Control:  
Loud:  
+ 2 dB at 8 kHz  
General  
Dimensions (w/o projecting parts/controls):  
Mass:  
179 x 50 x 150 mm  
Approx. 1.4 kg  
Power Requirement (neg. grnd.):  
Operating Temperature:  
Supplied Accessories:  
12 V DC car battery (11-16 V DC allowable)  
-20°C to 60°C  
• Unit  
• Faceplate (Release Panel)  
• Wire Harness  
• DIN Sleeve  
• Mounting Hardware  
• Owner’s Manual  
• Car Radio Passport  
• Labels  
Design and specifications subject to change without notice.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Blaupunkt-Werke GmbH  
Bosch Gruppe  
02/97  
18  
K7/VKD 8 622 400 896  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bionaire Humidifier BCM7309 User Manual
Bissell Hot Beverage Maker 29H3 User Manual
Black Box Telephone FX160A User Manual
Bogen Stereo Amplifier CAM User Manual
Boss Audio Systems Stereo System BV8975B User Manual
Brinkmann Heart Rate Monitor S810I User Manual
Broil King Gas Grill 9896 84 User Manual
Cadillac Automobile 2011 Escalade Hybrid User Manual
Canon Digital Camera 350D XT User Manual
Chicago Electric Marine Battery 91848 User Manual