Blaupunkt Car Stereo System CR 47 User Manual

Radio / Cassette  
Lima CR 47  
Operating instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features  
Radio Features  
- 15 FM/5 AM Presets, Including 5 FM and 5 AM Travelstore Presets  
- Station Scan  
- Local/Distant Seek and Manual Tuning  
Cassette Tape Player Features  
- Auto-Reverse Cassette Mechanism  
- True Fast-Forward/Rewind  
- Hard Permalloy Tape Head  
- Radio Monitor with Radio Preset Access  
Audio Features:  
- 10 Watts x 4 Channel Integrated Amplifier  
- Adjustable Maximum Turn-On Volume  
- Bass, Treble, Balance and Fader Control  
- Loudness Button  
- Mute Button  
Other Features:  
- Detachable Face  
- Illumination, Amber Night Design  
- Display Priority Control  
- Temporary Display Change Control  
- Clock Recall  
- 179 x 50 x 150 mm DIN/ISO Chassis  
- Detachable Wire Harness  
- Snap-In DIN Sleeve and Mounting Hardware  
Your unit’s detachable front faceplate makes the unit useless to would-be thieves.  
Designed, Engineered and Manufactured By Blaupunkt.  
Traffic Safety and Precautions  
Do not adjust your unit in difficult driving conditions that demand your full attention.  
As the driver of a motor vehicle, it is your responsibility to pay attention to the traffic situation  
at all times. Never use your unit in a way that could distract you.  
Always make sure that you are still able to hear any warning signals coming from outside of  
the vehicle, such as police or fire engine sirens, so that you can react accordingly.  
If your vehicle was parked in direct sunlight resulting in a considerable rise in temperature  
inside the vehicle, allow the unit to cool off before operating it.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Detachable Face (Release Panel)  
Detaching and Attaching the Face:  
The face of this unit can be detached and taken with you to prevent it from being stolen.  
Detaching the Face:  
Press the REL (Release) Button and detach the face by gently pulling it off as illustrated.  
Note: Do not pull it straight out from the chassis. Be sure not to drop the face when detaching it  
from the chassis. Do not expose the face to direct sunlight, heat sources such as hot air ducts or  
leave it in a humid place.  
Attaching the Face:  
Apply the right hand side of the face to the chassis by sliding (part B) of the face to (part A) at  
the front of the chassis. Gently push the left side of the face against the front of the chassis until  
it snaps into place.  
Note: Make sure that the face is inserted right side up. Do not press against the display window.  
Do not press hard against the face when attaching it to the chassis, it may be easily attached  
with gentle pressure.  
Affixing Faceplate For Retail Display:  
The faceplate can be affixed to the unit’s chassis, which is desirable for a retail display, for  
example. This should only be done in situations where the unit can be accessed from  
behind the mounting surface. Once the faceplate is affixed, the release keys cannot be  
used to remove the chassis.  
To affix the faceplate:  
Insert the black bolt into the hole at the left front of the top of the radio. See * below.  
*
A
B
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electrical Connections  
To avoid the aggravation of costly mistakes and serious damage, please carefully read all of the  
instructions before you begin. Carefully follow all instructions.  
General Recommendations  
If you’re not confident that you can install the unit correctly, have it installed by a qualified  
Blaupunkt installation technician.  
Use this unit only with negative ground 12 Volt (11-16 Volt) direct current (DC).  
Be sure to detach the faceplate before you start to connect or install the unit.  
We recommend making and testing all electrical connections before installing the unit.  
Connect the leads (wires) according to instructions and diagram below.  
Electrical Connection Instructions  
1. Disconnect the vehicle battery’s negative terminal before making connections.  
2. Connect the speakers and/or external amplifiers (if you have any) following the guidelines in  
the “Speaker Connection” section below.  
3. Connect the antenna output lead to the antenna motor trigger input terminal (if you have  
one). The total amperage required of the antenna lead must not exceed 100 mA. Do not  
connect the antenna lead to the antenna’s power supply input.  
4. Connect the ground lead to a grounded metal part on the vehicle. We recommend  
grounding all audio system ground leads (head unit, external amplifier, etc.) to a common  
grounding point, preferably a non-painted surface under the instrument panel.  
5. Connect the battery input lead to a source of constant battery power, preferably a terminal  
to an appropriate slot in the fuse box.  
6. Connect the ignition input lead only after the other leads are connected. Be sure to connect  
the ignition lead to a positive (+) 12 Volt power terminal that is energized only when the  
ignition key is set to the on position or accessory position.  
7. Cover the ends of any unused leads with electrical tape. This will prevent them from  
touching the vehicle or each other and causing a short-circuit and damage to the radio or  
vehicle.  
8. Reconnect the vehicle’s battery.  
9. Verify that no fuses have blown.  
10. Plug the harness into the unit.  
Electrical Connections  
Ignition  
+12V  
Antenna  
Ground –  
+12V  
Battery  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker Connections  
Speaker Connections  
R
L
LF  
F
R
R
R
+
-
+
-
+
-
+
-
RF  
LF  
RR  
LR  
Attach the faceplate and test the unit.  
Once the connections have been successfully made, you can begin to mount the unit.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Recommendations  
The illustration below shows a typical installation, however, you may need to adjust the  
installation, depending on the unit. If you have questions or need additional installation  
hardware, consult your Blaupunkt dealer.  
Make sure the unit is firmly anchored and does not vibrate.  
Mounting Hardware  
Release Keys  
Sleeve  
Mounting The Unit in Most Dashboards  
1. Install the Sleeve in the dashboard.  
2. Select and bend the appropriate tabs to hold the sleeve firmly in place.  
Bend these tabs  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting the Unit in a Japanese Car  
You may have difficulty mounting this unit in some Japanese cars that have ISO mounting  
features. In this case, consult your Blaupunkt dealer.  
1. Run a blade along the slits on the back of the front trim ring, unscrew the two side screws,  
and separate it from the unit. Save the trim ring and related hardware in case you ever want  
to install the unit in another vehicle.  
2. Use the vehicle’s own mounting hardware to attach the unit.  
2 TOYOTA  
1
max. size M5x8  
Slit  
to dashboard/center console  
max. size  
M5x8  
Bracket  
Support  
2 NISSAN  
max. size M5x8  
to dashboard/center console  
max. size  
M5x8  
Bracket  
Support  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
Removing the Unit  
Use the Release Keys as shown below. Keep them in a safe place in case you need them in the  
future.  
Fuse Replacement  
When replacing the fuse, be sure to use one with the correct amperage, which will be stated on  
the fuse case. Never use a fuse that has a stated amperage exceeding the one supplied for this  
unit, as this could cause malfunction and serious damage to the unit.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Location of Controls  
1
2
3
4
5
REL (Release) – Detaching Faceplate  
ON (Power)  
– Turning Unit On  
– Source and Radio Band Select  
– Cassette Eject  
– Mute  
SRC  
AUDIO  
SCA  
TS  
– Audio / Clock Adjust :00  
– Scan  
6
7
– Travelstore  
LD  
– Loudness  
SENS  
– Tuning Sensitivity  
8
9
Cassette Insertion Slot  
CLK  
– Clock Recall  
DISP  
– Display Change  
10/11 PROG  
– Tape Program Change (reverse)  
– Fast Rewind  
10  
11  
12  
13  
14  
15  
16  
17  
FR  
FF  
+
– Fast Forward  
– Volume + / Bass + / Treble + / Balance Left / Fade to Front  
– Volume - / Bass - / Treble - / Balance Right / Fade to Rear  
– Seek and Manual Tuning / Clock Hours  
– Seek and Manual Tuning / Clock Minutes  
– FM/AM Presets  
1, 2, 3, 4, 5  
Display  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instructions – General Operation  
See Traffic Safety and Precautions on page 19.  
“Press” means a momentary press of less than 1/2 second. All presses requiring more than 1/2  
second are followed by beep.  
“Time Out” When additional button presses are anticipated to complete a procedure, the unit will  
automatically exit the procedure after 4 seconds of inactivity.  
Clock Recall  
Vehicle ignition must be on. The display switches to clock.  
Ignition-On / Turning Unit Off  
Press the ON Button to turn the unit off.  
Release for Detachable Faceplate  
Push REL to detach face. Already inserted cassette remains in unit. Current settings and source  
mode are stored. If power was not switched off before face removed, unit will automatically  
power-on when face is reattached.  
Power On/Off  
When ignition on, press ON or insert a disc to turn unit on. Last-used source becomes active,  
unless unit is turned on by inserting tape, in which case tape player becomes active.  
Power Off  
Press ON to turn unit off. Unit stores current settings for source, station or track, etc. Antenna/  
amplifier trigger wire shuts off voltage. (If faceplate still attached, display switches to clock.)  
Setting the Clock  
Turn the unit on. Press the CLK Button for four seconds until the clock starts blinking. (The  
display will change after two seconds. Ignore this and continue to hold for two more seconds.)  
Once the clock starts blinking, Press the to set the hour, and press the Button to set the  
minutes. (To change the minute indicator to the nearest hour (:00), you can press the AUDIO  
Button. Press the CLK Button again to activate the clock.  
Changing the Information Displayed  
You can temporarily change the information shown in your unit’s display. You can also select  
which information has “display priority” and is shown in the display except for moments when  
adjustments are made.  
To change the display priority, press the DISP Button for two seconds. The display priority  
changes. The display priority choices are clock or radio frequency/“TAPE”.  
To change the display temporarily, press and release the DISP Button to access the desired  
information. After four seconds, the display changes back to the priority information.  
Source (SRC)  
Use SRC to select source - AMT, FM1, FM2, FMT or cassete (if already inserted).  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Operation  
Volume Control Buttons (+/–)  
Press + and to increase/decrease volume from 0 to 63.  
Adjustable Maximum Turn-On Volume  
Press and hold the ON Button for more than two seconds. The unit turns off and the turn-on  
volume level is memorized.  
Mute  
Press  
to temporarily reduce volume. “MUTE” appears. Mute is terminated by pressing any  
button.  
Bass, treble, balance and fader  
Bass  
Hould down the AUDIO Button until “BASS” appears and then press immediately + or to  
increase or decrease bass in intervals between 7 and -7.  
Treble  
Hold down the AUDIO Button until “BASS” appears. Then press AUDIO once again so that  
“TREb” appears. Now press immediately + or – to increase or decrease treble in intervals  
between 7 and -7.  
Balance  
Hold down the AUDIO Button until “BASS” appears. Then press AUDIO twice so that “BAL”  
appears. Now press immediately + or to adjust the left/right volume between 9 (left) and -9  
(right).  
Fader  
Hold down the AUDIO Button until “BASS” appears. Then press AUDIO three times so that  
“FADE” appears. Now press immediately + or - to adjust the front/rear volume between 9  
(front) and -9 (rear).  
Loudness (LD)  
Press LD to increase sound of low and high frequencies. “LOUD” icon appears. To cancel,  
press LD again.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Radio Operation  
Last Station Memory  
Each FM bank and AM band has its own last station memory which holds last-tuned frequency  
for that band or bank irrespective of whether that frequency is stored into a preset.  
Selecting Bands  
Press SRC as needed to access FM1, FM2, FM3/FMT, AM/AMT banks.  
Seek Tuning  
Press or to seek next receivable frequency. Tuning stops at frequency that fulfills sensitivity  
requirements predetermined by sensitivity set through SENS button.  
Tuning Sensitivity (SENS)  
Press SENS for more that 2 seconds to switch between local (lo) and distant (dx) search  
sensitivity.  
Radio Reception Hints  
When listening to weak or distant AM stations, adjusting the Treble to minimum (-7) will  
reduce noise and improve sound.  
In general, set SENS to DX if in rural areas or where stations tend to be weak and distant,  
and to LO when in metropolitan areas or where stations tend to be strong and local.  
Stereo Symbol  
Stereo symbol turns on if a stereo station with a sufficiently strong signal is received. The unit  
gradually switches between mono to stereo automatically.  
Manual Tuning  
Press or for more than 1/2 second and frequency will go one channel/step in direction  
pressed. Press and hold causes continuous manual tuning. Unit returns to seek tuning mode  
after 4 seconds or after storing a station on a preset.  
Preset Station Storage  
After tuning desired frequency on desired band, press and hold a Preset Button for more than  
2 seconds to store current frequency. Audio is muted during storage, preset number appears,  
and beep acknowledges storage.  
Preset Station Selection  
Press desired Preset Button.  
Travelstore  
In any FM Bank, press TS for 2 seconds to activate FM Travelstore. (In AM Bank, press it for 2  
seconds to activate AM Travel Store.) “TS” appears. Beginning at the bottom of the band, TS  
stores five relatively strong stations and returns to preset 1. To cancel search operation, press  
TS, any present button or the or key.  
Station Scan Tuning  
Press SCA. Frequency blinks during scanning. Unit stops at receivable stations for 4 seconds.  
Unit continuously scans until user stops scan by pressing SCA, another tuning button or SRC.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cassette Tape Player Operation  
Tape Playback:  
Insert cassette into Cassette Door. (Note: Make sure that the side of the cassette exposed is  
facing right and that all slack has been removed from the tape prior to insertion.)  
If ignition switch is already in “on” or accessory position, insertion of cassette will turn unit  
on. If unit already turned on, cassette insertion will override other audio source, such as  
radio. “LOAD” appears for 2 seconds. Cassette play will begin, and the display will indicate  
which tape program is in use, “1” or “2”.  
The tape will continue to play until ejected, SRC button pressed, or unit turned off.  
Ejecting The Tape  
Press the button completely towards the face of the unit. The tape will eject. If uit is turned on,  
“EJ” will appear in the display for 2 seconds and the last-heard radio station will play.  
Tape Program Change  
Automatic Change (Autoreverse): When the end of the tape is reached, the unit will  
automatically reverse direction and play the other side of the tape.  
Manual Change: To manually reverse tape direction, press both PROG (program) Buttons  
(FR and FF) at the same time.  
The change in direction and in tape program will be confirmed in the display (“1” or “2”).  
Fast Winding  
To Fast-Rewind the tape, press the FR Button. Tape rewinds and blinks in the display.  
To Fast-Forward the tape, press the FF Button. Tape fast-forwards and  
display.  
blinks in the  
To stop fast-winding, press the other fast winding button, FR or FF.  
Radio Monitor  
During tape winding, the radio will play the most-recently heard radio frequency. All frequencies  
stored on the current bank of preset stations are accessible during fast winding.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Guide  
General  
Trouble  
Cause/Solution  
No sound.  
• Adjust the volume with the + button.  
• With a two-speaker system set the fader control to the  
center position.  
Radio reception  
Trouble  
Cause/Solution*  
Preset stations are not receivable.  
• The broadcast is too weak.  
Automatic tuning is not possible.  
• The broadcast is too weak. —> Use manual tuning.  
• Not enough broadcast frequencies are receivable.  
Travel Store feature does not complete  
storing of five stations.  
* Also make sure that antenna is connected and extended.  
If the above mentioned solutions do not help to improve the situation, consult your nearest Blaupunkt  
dealer.  
Blaupunkt Telephone Hotline  
Address of the next service centre in your vicinity  
(only for Germany)  
If you would like to know the address of the next Blaupunkt service centre of your area  
without having our service list at hand:  
-
-
-
Find out your area code.  
Then call the following chargeable phone number: 01 80 / 5 25 56 66.  
Using the area code to be entered you will be automatically given the address and  
phone number of the next Blaupunkt service centre. You can also request this informa-  
tion by fax.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Audio Power Specifications  
Power Output and Total Harmonic Distortion: 5.5 watts per channel minimum continuous  
average output into 4 ohms, 4 channels driven, from 35-15000 Hz.  
Other Specifications  
Tuner  
FM  
Tuning Range:  
87.5 - 108 MHz  
1.3 µV  
65 dB (stereo), 70 dB (mono)  
35-15000 Hz  
FM Mono Sensitivity:  
Signal-to-Noise Ratio:  
Frequency Response:  
AM  
Tuning Range:  
Signal-to-Noise Ratio:  
Frequency Response:  
531 - 1602 kHz  
50 dB  
35-5000 Hz  
Cassette  
Signal-to-Noise Ratio:  
Tape Wow and Flutter:  
Tape Frequency Response:  
55 dB  
0.3 %  
35-15000 Hz  
Audio  
Speaker Impedance:  
Maximum Amp Power:  
RMS Power:  
4-8 ohms  
4 X 10 watts (at 4 ohms)  
4 X 5.5 watts (at 4 ohms)  
acc. to DIN 45 325 at 14.4 volts  
± 10 dB at 100 Hz  
± 10 dB at 10 kHz  
+ 8 dB at 60 Hz  
Bass Control:  
Treble Control:  
Loud:  
+ 2 dB at 8 kHz  
General  
Dimensions (w/o projecting parts/controls):  
Mass:  
179 x 50 x 150 mm  
Approx. 1.4 kg  
Power Requirement (neg. grnd.):  
Operating Temperature:  
Supplied Accessories:  
12 V DC car battery (11-16 V DC allowable)  
-10°C to 50°C  
• Unit  
• Faceplate  
• Wire Harness  
• DIN Sleeve  
• Mounting Hardware  
• Owner’s Manual  
Design and specifications subject to change without notice.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Blaupunkt-Werke GmbH  
Bosch Gruppe  
11/96  
K7/VKD 8 622 400 953  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Billy Goat Snow Blower F091907A User Manual
Black Decker Vacuum Cleaner BDH2000SDL User Manual
Braun Hot Beverage Maker 3214 User Manual
Bryant Furnace 320AAZ User Manual
Cannon Camcorder XL2 User Manual
Canon Printer BJ 200ex User Manual
Casio Electronic Keyboard CS 44P User Manual
Casio Watch 2036 1 User Manual
Chrysler Automobile 2004 Sebring Sedan User Manual
Cino Barcode Reader F760 User Manual