GPC1800L
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
• Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
• When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
Intended use
Your Black & Decker cordless pole pruner has
been designed for pruning trees. This tool is
intended for consumer use only.
Your Black & Decker charger has been designed
for charging Black & Decker batteries of the type
supplied with this tool.
Safety instructions
• If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
General power tool safety warnings
Warning! Read all safety warnings
and all instructions.
Failure to follow the warnings and
instructions listed below may result in
electric shock, fire and/or serious injury..
Personal safety
• Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the
switch is in the off-position before connect-
ing to power source and/or battery pack,
picking up or carrying the tool. Carrying
power tools with your finger on the switch or
energising power tools that have the switch on
invites accidents.
Save all warnings and instructions for future
reference.
The term “power tool” in all of the warnings listed
below refers to your mains operated (corded)
power tool or battery operated (cordless) power
tool.
Work area safety
• Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
• Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
• Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
• Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unexpected
situations.
• Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.
• If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
Electrical safety
• Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
• Avoid body contact with earthed or
grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an
increased risk of electric shock if your body is
earthed or grounded.
• Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
• Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
Power tool use and care
• Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
• Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
• Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
Service
• Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Additional safety instructions for pole
pruners
• Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
• Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage
of parts and any other condition that may
affect the power tools operation. If dam-
aged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
• Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
• Use the power tool, accessories and tool
bits etc., in accordance with these instruc-
tions, taking into account the working condi-
tions and the work to be performed. Use
of the power tool for operations different from
those intended could result in a hazardous
situation.
The intended use is described in this instruction
manual. Do not use the tool for purposes not
intended; for example do not use the tool to fell
trees. The use of any accessory or attachment or
performance of any operation with this tool other
than those recommended in this instruction manual
may present a risk of personal injury.
• Wear close fitting and protective clothing
including a safety helmet with visor/goggles, ear
protectors, non-skid safety footwear, protective
bib trousers and strong leather gloves.
• Always position yourself out of the path of
falling branches.
• The safe distance between a branch to be
felled and bystanders, buildings and other
objects is at least 2 1/2 times the length of the
branch. Any bystander, building or object within
this distance is at risk from being struck by the
falling branch.
• Pre-plan a safe exit from falling trees or
branches. Ensure the exit route is clear
of obstacles that would prevent or hinder
movement. Remember wet grass and freshly
cut bark is slippery.
Battery tool use and care
• Ensure someone is nearby (but at a safe
distance) in case of an accident.
• Recharge only with the charger specified by
the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of
fire when used with another battery pack.
• Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and
fire.
• Do not use the tool while standing in a tree, on
a ladder or on any other unstable surface.
• Keep proper footing and balance at all times.
• Hold the tool firmly with both hands when the
motor is running.
• Do not let the moving chain contact any object
at the tip of the guide bar.
• When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws, or other
small metal objects, that can make a con-
nection from one terminal to another. Short-
ing the battery terminals together may cause
burns or a fire.
• Start cutting only with the chain moving at full
speed.
• Do not attempt to enter a previous cut. Always
make a fresh cut.
• Watch for shifting branches or other forces that
could close a cut and pinch or fall into the chain.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
• Do not attempt to cut a branch when the
diameter of the branch exceeds the cutting
length of the tool.
• Always remove the battery from the tool and
place the chain cover over the chain when
storing or transporting the tool.
Warning! The vibration emission value during
actual use of the power tool can differ from
the declared value depending on the ways in
which the tool is used. The vibration level may
increase above the level stated.
• Keep the saw chain sharp and properly ten-
sioned. Check the tension at regular intervals.
• Switch the tool off, allow the chain to stop and
remove the battery from the tool before carrying
out any adjustment, servicing or maintenance.
• Only use genuine replacement parts and
accessories.
• Carry the pole pruner by the handle with the
cutter blade stopped. When transporting or stor-
ing the pole pruner always fit the cutting device
cover and dismantle it into its component parts.
Proper handling of the pole pruner will reduce
possible personal injury and injury to others.
When assessing vibration exposure to determine
safety measures required by 2002/44/EC to protect
persons regularly using power tools in employ-
ment, an estimation of vibration exposure should
consider, the actual conditions of use and the
way the tool is used, including taking account of
all parts of the operating cycle such as the times
when the tool is switched off and when it is running
idle in addition to the trigger time.
Pruning
Before attempting to prune a tree, ensure there are
not by-laws or regulations that would prohibit or
control the felling of the tree.
Residual risks
• Be aware of the direction a branch may fall.
Consider all conditions that may affect the
direction of fall, including:
Additional residual risks may arise when using the
tool which may not be included in the enclosed
safety warnings. These risks can arise from mis-
use, prolonged use etc.
-the length and weight of the branch to be cut
-the intended direction of fall
Even with the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks can not be avoided.
These include:
-any unusual heavy limb structure or decay
-the presence of surrounding trees and
obstacles,
-including overhead lines
• Injuries caused by touching any rotating/moving
parts.
• Injuries caused when changing any parts,
blades or accessories.
• Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
-the intertwinement with other branches
-the speed and direction of the wind.
• Consider access to the tree limb.
Tree branches are liable to swing towards the tree
trunk. In addition to the user, any bystander, build-
ing or object below the branch is at risk of being
struck by the branch.
• Impairment of hearing.
• Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech and
MDF.)
Safety of others
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for the their safety.
Vibration
The declared vibration emission values stated in
the technical data and the declaration of conform-
ity have been measured in accordance with a
standard test method provided by EN 60745 and
may be used for comparing one tool with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
• Children should be supervised to ensure that
they do not play with the appliance.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
• Do not damage/deform the battery pack either
by puncture or impact, as this may create a risk
of injury and fire.
Warning symbols
The following warning symbols are found on the
tool:
• Do not charge damaged batteries.
• Under extreme conditions, battery leakage may
occur. When you notice liquid on the batteries
Carefully wipe the liquid off using a cloth. Avoid
skin contact.
Warning! To reduce the risk of
injury, the user must read the
instruction manual.
Do not use the tool in wet conditions
or expose it to rain.
• In case of skin or eye contact, follow the
instrucitons below.
Always wear head and eye protection.
Wear non-slip safety footwear.
Warning! The battery fluid may cause personal
injury or damage to property. In case of skin
contact, immediately rinse with water. If red-
ness, pain or irritation occurs seek medical
attention. In case of eye contact, rinse im-
mediately with clean water and seek medical
attention.
Beware of falling objects. Keep by-
standers away.
Chargers
Your charger has been desinged for a specific
voltage. Always check that the mains voltage cor-
responds to the voltage on the rating plate.
Warning! Never attempt to replace the charger
unit with a regular mains plug.
• Use your Black & Decker charger only to
charge the battery in the applaince/tool with
which it was supplied. Other batteries could
burst, causing personal injury and damage.
• Never attempt to charge non-rechargeable
batteries.
10m
Electrocution hazard. Keep at least
10 m away from overhead lines.
To ensure continued safe operation,
check the chain tension as described
in this manual after every 10 minutes
of use, and adjust back to a clearance
of 3 mm as required. Oil the chain
after every 10 minutes of use
Direction of rotation of the chain.
• If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Black & Decker Service Centre in order to avoid
a hazard.
• Do not expose the charger to water.
• Do not open the charger.
Warning! Do not touch chain at the
chip ejection point.
Additional safety instructions for bat-
teries and chargers
• Do not probe the charger.
• The appliance/tool/battery must be placed in a
well ventilated area when charging.
Batteries
• Never attempt to open for any reason.
• Do not expose the battery to water.
• Do not expose the battery to heat.
• Do not store in locations where the temperature
may exceed 40 °C.
Labels on the charger
The following symbols are found on your charger:
• Charge only at ambient temperatures between
10 °C and 40 °C.
• Charge only using the charger provided with the
applaince/tool. Using the wrong charger could
result in an electric shock or overheating of the
battery.
The charger is intended for indoor
use only
Read the instruction manual before
use.
• When disposing of batteries, follow the
instructions given in the section “Protecting the
environment”.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
Fitting the saw head (fig. C)
The saw head can be fitted directly to the handle in
order to achieve standard reach.
• Align the groove on the outside of the coupling
end of the handle (3) with the tongue on the
inside of the coupling end of the saw head (4).
Push the saw head (4) onto the handle (3).
• Slide the collar (14) down and rotate it
clockwise until it is fully tightened.
The charger automatically shuts off
if the ambient temperature becomes
too high. As soon as the ambient
temperature has cooled down, the
charger will resume operating.
130oC
+40ºC
+10ºC
Charge only at ambient temperatures
between 10 °C and 40 °C.
Warning! Periodically check the connections to
ensure that they are tightened securely.
Electrical safety
Your charger is double insulated;
therefore no earth wire is required.
Always check that the mains voltage
corresponds to the voltage on the rat-
ing plate. Never attempt to replace the
charger unit with a regular mains plug.
Extending the saw head (fig. D)
The maximum reach can be achieved by fitting the
extension tube (10) between the saw head (4) and
the handle (3).
• Align the groove on the outside of the coupling
end of the handle (3) with the tongue on the
inside of the coupling end of the extension tube
(10).
Overview
1. On/off switch
2. Lock-off button
3. Main handle
4. Saw head
• Push the extension tube (10) onto the handle
(3).
• Slide the collar (15) down and rotate it
clockwise until it is fully tightened.
• Align the groove on the outside of the coupling
end of the extension tube (10) with the tongue
on the inside of the coupling end of the saw
head (4).
5. Sprocket cover
6. Guide bar
7. Chain
8. Chain sheath
9. Lubrication bottle
10.Extension tube
11.Battery
• Push the saw head (4) onto the extension tube
(10).
• Slide the collar (14) down and rotate it
clockwise until it is fully tightened.
Warning! Periodically check the connections to
ensure that they are tightened securely.
Fig. A
12.Charger
Removing the saw head (fig. C & D)
If the extension tube (10) is fitted, the saw head
must be removed first.
• To remove the saw head (4), rest the handle (3)
on the ground, loosen the collar (14) and take
off the saw head.
Assembly
Warning! Before assembly, remove the battery
from the tool.
Fitting and removing the battery (fig. B)
• To fit the battery (11), line it up with the
receptacle on the tool. Slide the battery into the
receptacle and push until the battery snaps into
place.
• To remove the battery, push the release button
(13) while at the same time pulling the battery
out of the receptacle.
Warning! To prevent accidental operation,
ensure that the battery is removed and that
the chain sheath is in place on the saw chain
before performing the following operations.
Failure to do this could result in serious per-
sonal injury.
Use
Warning! Let the tool work at its own pace. Do
not overload.
Charging the battery (fig. A)
The battery needs to be charged before first use
and whenever it fails to produce sufficient power
on jobs that were easily done before. When charg-
ing the battery for the first time, or after prolonged
storage, it will only accept an 80% charge.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
After several charge and discharge cycles, the
battery will attain full capacity. The battery may
become warm while charging; this is normal and
does not indicate a problem.
Switching on and off (fig. E)
For your safety, this tool is equipped with a double
switching system. This system prevents starting
the tool inadvertently.
Warning! Do not charge the battery at ambi-
ent temperatures below 10 °C or above 40 °C.
Recommended charging temperature: approx.
24°C.
Switching on
• Push the lock-off button (2) backward using
your thumb and at the same time squeeze the
on/off switch (1).
Note: The charger will not charge a battery if
the cell temperature is below approximately 0
°C or above 60 °C.
The battery should be left in the charger and
the charger will begin to charge automatically
when the cell temperature warms up or cools
down.
• Release the lock-off button (2).
Switching off
• Release the on/off switch (1).
Warning! Never attempt to lock a switch in the
on position.
• To charge the battery (11), remove it from the
tool and insert it into the charger (12). The
battery will only fit into the charger in one way.
Do not force. Be sure that the battery is fully
seated in the charger.
• Plug in the charger and switch on at the mains.
The charging indicator (24) will flash continuously
(slowly).
The charge is complete when the charging indica-
tor (9) lights continuously. The charger and the
battery can be left connected indefinitely with the
LED illuminated. The LED will change to flashing
(charging) state as the charger occasionally tops
off the battery charge. The charging indicator (24)
will be lit as long as the battery is connected to the
plugged-in charger.
Pruning (fig. F)
• Make sure the tool is running at full speed
before making a cut.
• Hold the tool firmly in place to avoid possible
bouncing or sideways movement of the tool.
• Guide the tool through the branch using light
pressure. When cutting heavy branches, where
a partial cut may splinter and damage the tree,
proceed as follows:
-Make the first cut 15 cm from the tree trunk on
the underside of the limb. Use the top of the
guide bar (7) to make this cut.
-Cut one third through the diameter of the limb.
Then cut down from the top.
Cleaning, maintenance and storage
Your Black & Decker corded/cordless appliance/
tool has been designed to operate over a long
period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
• Charge discharged batteries within 1 week.
Battery life will be greatly diminished if stored in
a discharged state.
•
Charging indicators
If the charger detects a problem with the battery,
the charging indicator (24) will flash at a fast rate.
Proceed as follows:
Warning! Before performing any maintencance
on corded/cordless power tools:
• Switch off and unplug the appliance/tool
• Or switch off and remove the battery from
the appliance/tool if the appliance/tool has a
separate battery pack
• Re-insert the battery (11).
• If the charging indicators continues flashing at a
fast rate, use a different battery to determine if
the charging process works properly.
• If the replaced battery charges correctly, the
original battery is defective and should be
returned to a service centre for recycling.
• If the new battery gives the same indication
as the original battery, take the charger to be
tested at an authorised services centre.
Note: It may take as long as 15 minutes to
determine that the battery is defective. If the
battery is too hot of too cold, the LED will al-
ternately blink fast and slow, one flash at each
speed and repeat.
• Or run the battery down completely if it is
integral and then switch off
• Unplug the charger before cleaning it. Your
charger does not require any maintenance
apart from regular cleaning.
Regularly clean the ventilation slots in you appli-
ance/tool/charger using a soft brush or dry cloth.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
Regularly clean the motor houseing using a damp
cloth. Do not use any abrasive or solvent-based
cleaner.
Regularly open the chuck and tap it to remove any
dust from the interior (when fitted).
Checking and adjusting the chain tension
(fig. G)
• Check the saw chain tension. The tension is
correct when the saw chain (7) snaps back
after being pulled away 3 mm from the saw
chain bar with light force from the middle finger
and thumb. There should be no ‘sag’ between
the guide bar (6) and the saw chain (7) on the
underside.
After use and before storage
• Regularly clean the ventilation slots with a
clean, dry paint brush.
• To clean the tool, use only mild soap and a
damp cloth. Never let any liquid get inside the
tool and never immerse any part of the tool into
liquid.
• Remove debris using a hard brush.
• Lubricate the chain with oil.
To adjust the tension:
• Loosen the screws (16).
• Turn the screw (18) clockwise.
Warning! Do not over-tension the chain as this
will lead to excessive wear and will reduce the
life of the bar and chain.
• Once the chain tension is correct, tighten the
screws (18).
Installing and removing the saw chain
(fig. G & H)
Warning! Always wear protective gloves when
installing or removing the saw chain. The saw
chain is sharp and can cut you when it is not
running.
Warning! When the saw chain is new, check the
tension frequently during the first two hours of
use as a new saw chain stretches slightly.
• Place the tool on a firm and stable surface.
• Loosen the screws (16) using the Allen key
provided. Remove the screws.
• Remove the sprocket cover (5) and the bar
clamp (17).
• Turn the screw (18) counterclockwise to allow
the guide bar (6) to recede and to reduce the
tension on the saw chain (7).
• Remove the old saw chain from the sprocket
(19) and the guide bar (6).
• Place the new saw chain in the groove of the
guide bar and around the sprocket. Make sure
that the teeth are facing the correct direction by
matching the arrow on the saw chain with the
arrow on the housing.
• Make sure that the slot (20) in the guide bar
is over the location pins (21) and that the hole
(22) below the slot is located over the adjust-
ment pin (23).
• Re-fit the sprocket cover (5) and the bar clamp
(17) and the screws (16).
• Tighten the screws (16) using the Allen key
provided.
Oiling the chain
The saw chain must be oiled before each use and
after cleaning using only the correct grade of oil
(cat. no. A6027).
• Oil the whole saw chain (7) evenly using the
applicator (9).
Storage
When the tool will not be used for several months,
ideally leave the battery connected to the charger.
Otherwise proceed as follows:
• Fully charge the battery.
• Remove the battery from the tool.
• Store the tool and battery in a secure and dry
location.
• The storage temperature must always remain in
the range of +10 °C to +40 °C. Place the battery
on a level surface.
• Before using the tool after prolonged storage,
fully charge the battery again.
Protecting the environment
• Adjust the chain tension as described below.
To ensure continued safe operation, the chain
and guide bar must only be replaced with original
Black & Decker parts. Replacement chain part
number A6158 replacement guide bar part number
623381-00.
Separate collection. This product must
not be disposed of with normal house-
hold waste.
Should you find one day that your Black & Decker
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
Separate collection of used products
and packaging allows materials to
be recycled and used again. Reuse
of recycled materials helps prevent
environmental pollution and reduces the
demand for raw materials.
Technical data
GPC1800L
(H1)
Voltage
No-load chain speed m/min
Weight Kg
VDC
18
114
3.5
17
Local regulations may provide for separate collec-
tion of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
Black & Decker provides a facility for the collection
and recycling of Black & Decker products once
they have reached the end of their working life. To
take advantage of this service please return your
product to any authorised repair agent who will col-
lect them on our behalf.
Max. Cutting Length cm
Battery
A1518L
18
Voltage
Capacity
Weight
VDC
Ah
Kg
1.5
0.45
Charger
9053954*
You can check the location of your nearest author-
ised repair agent by contacting your local Black
& Decker office at the address indicated in this
manual. Alternatively, a list of authorised Black &
Decker repair agents and full details of our after-
sales service and contacts are available on the
Internet at:
Input Voltage
Output Voltage
Current
VAC
VDC
A
230
21
1.9
8
Approx. charge time
h
Level of sound power according to
EN ISO 3744: LWA = 98 dB(A),
uncertainty (K) = 3 dB(A)
Batteries
Level of sound pressure according to
EN ISO 11203: LPA = 78 dB(A),
uncertainty (K) = 3 dB(A)
At the end of their useful life, discard
batteries with due care for our environ-
ment
• Do not short-circuit the battery terminals.
• Do not dispose of the battery(s) in a fire as
this may result in a risk of personal injury or an
Explosion.
• Run the battery down completely, then remove
it from the tool.
• Batteries are recyclable. Place the battery(s)
in a suitable packaging to ensure that the
terminals cannot be short-circuited. Take
them to any authorised repair agent or a local
recycling station.
Vibration total values (triax vector sum) deter-
mined according to EN 60745
Vibration emission
value ah=
m/
s2
<2.5
<1.5
Cutting wood
m/
s2
Uncertainty K=
11
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
EC - Declaration of Conformity
Guarantee
Black & Decker is confident of the quality of its
products and offers an outstanding guarantee. This
guarantee statement is in addition to and in no way
prejudices your statutory rights.
MACHINERY DIRECTIVE
The guarantee is valid within the territories of the
Member States of the European Union and the
European Free Trade Area.
GPC1800L
If a Black & Decker product becomes defective
due to faulty materials, workmanship or lack of
conformity, within 24 months from the date of
purchase, Black & Decker guarantees to replace
defective parts, repair products subjected to fair
wear and tear or replace such products to ensure
minimum inconvenience to the customer unless:
• The product has been used for trade, profes-
sional or hire purposes;
Black & Decker declares that these products
described under “technical data” are in compliance
with:
2006/42/EC EN60745-1,
These products also comply with Directive
2004/108/EC. For more information, please contact
Black & Decker at the following address or refer to
the back of the manual.
• The product has been subjected to misuse or
neglect;
The undersigned is responsible for compilation of
the technical file and makes this declaration on
behalf of Black & Decker.
• The product has sustained damage through
foreign objects, substances or accidents;
• Repairs have been attempted by persons
other than authorised repair agents or Black &
Decker service staff.
To claim on the guarantee, you will need to submit
proof of purchase to the seller or an authorised
repair agent. You can check the location of your
nearest authorised repair agent by contacting your
local Black & Decker office at the address indicat-
ed in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our
after-sales service and contacts are available on
the Internet at:
Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
20-01-2010
co.uk to register your new Black & Decker product
and to be kept up to date on new products and
special offers. Further information on the Black &
Decker brand and our range of products is avail-
able at:
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
Do not forget to register your product!
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. 03-8720 5100
Fax 03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Auckland 1060
Tel. +64 9 259 1133
Fax +64 9 259 1122
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
90560539 REV-0
01/2010
Download from Www.Somanuals.com. All Manuals Search And Download.
|