ACS1009A
ACS2209A
ACS4001A
ACS4201A
DVI-D-CatX-KVM-Extender
Single and DualHead
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
Copyrights and Trademarks
©2005. All rights reserved. This information may not be reproduced in any manner without
the prior written consent of the manufacturer.
Information in this document is subject to change without notice and the manufacturer shall
not be liable for any direct, indirect, special, incidental or consequential damages in
connection with the use of this material.
All trademark and trade names mentioned in this document are acknowledged to be the
property of their respective owners.
Disclaimer
While every precaution has been taken in the preparation of this manual, the manufacturer
assumes no responsibility for errors or omissions. Neither does the manufacturer assume any
liability for damages resulting from the use of the information contained herein. The
manufacturer reserves the right to change the specifications, functions, or circuitry of the
product without notice.
The manufacturer cannot accept liability for damage due to misuse of the product or due to
any other circumstances outside the manufacturer’s control (whether environmental or
installation related). The manufacturer shall not be responsible for any loss, damage, or injury
arising directly, indirectly, or consequently from the use of this product.
Cautions and Notes
The following symbols are used in this guide:
CAUTION. This indicates an important operating instruction
that should be followed to avoid any potential damage to
hardware or property, loss of data, or personal injury.
NOTE. This indicates important information to help you make the best use of
this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DECLARATION OF CONFORMITY
EUROPEAN UNION DECLARATION OF CONFORMITY
This is to certify that, when installed and used according to the instructions in this
manual, together with the specified cables and the maximum cable length <3m, the
Units are shielded against the generation of radio interferences in accordance with the
application of Council Directive 89/336/EEC as well as these standards:
EN 55022:
EN 55024:
1999
1999
2001
2001
2001
2001
2001
2002
Class B
IEC 61000-4-2:
IEC 61000-4-3:
IEC 61000-4-4:
IEC 61000-4-5:
EN 61000-3-2
EN 61000-3-3
The device was tested in a typical configuration with PC.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
Safety Precautions and Installation Guidelines
To ensure reliable and safe long-term operation, please note the following installation
guidelines:
•
•
•
•
Do not use CATx-devices to link between buildings – please use fiber devices.
Only use in dry, indoor environments.
Do not use CATx-devices to link between buildings – please use fiber devices.
If the building has 3-phase AC power, try to ensure that equipment connected to the
Local and Remote units is on the same phase.
•
•
Try not to route a CATx link cable alongside power cables.
The Remote unit, Local unit and any power supplies can get warm. Do not locate them
in an enclosed space without any airflow.
•
•
Do not place a power supply directly on top of a unit.
Do not obstruct a unit’s ventilation existing holes.
To safeguard against personal injury and avoid possible
damage to equipment or property, please observe the
following:
•
Only use power supplies originally supplied with the
product or manufacturer-approved replacements. Do not
attempt to dismantle or repair any power supply. Do not
use a power supply if it appears to be defective or has a
damaged case.
•
•
Connect all power supplies to grounded outlets. In each
case, ensure that the ground connection is maintained
from the outlet socket through to the power supply’s AC
power input.
Do not attempt to modify or repair this product, or make
a connection from the CATx link interface (RJ45) to any
other products, especially telecommunications or
network equipment.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INHALTSVERZEICHNIS
Contents
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
1. Quick Setup
This section briefly describes how to install your KVM extender system. Unless you are an
experienced user, we recommend that you follow the full procedures described in the rest of
this manual.
Install system
1. Connect Remote unit to KVM.
2. Connect Local unit to CPU or switch.
3. Connect Local and Remote units with matching interconnection cable
(CATx).
4. Power up the system.
NO
Power LED
illuminated?
Check p.s.u.’s and connection
to power outlet
YES
NO
Link LED
illuminated ?
Check the CATx cable, and
CATx connectors
YES
Video OK
LED ?
NO
illuminated ?
Check settings of graphic card
or boot CPU
YES
Done
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW
2. Overview
2.1 Introduction
A Cat5 KVM Extender is mainly used, to extend the maximum distance between a CPU
and his Keyboard / Monitor / Mouse considerably. In addition they are irrecoverable in
installations in electromagnetic hazardous environments (EMI). Normal Keyboard-/
Monitor-/ Mouse extender cables (and Extender using traditional cables) cannot go so far
and EMI interferences may reduce the maximum distance and/or reliability. Using a
DVI-D Cat X Extender system, these limitations are past. Remain your CPU in a secure
rack cabinet or data center while accessing from a 140m remotely located place.
A basic KVM extension system comprises a Local unit (transmitter) and a Remote unit
(receiver). The Local unit connects directly to the computer (or a KVM switch system) using
the supplied cable(s). The user console (keyboard, mouse and monitor) attaches to the
Remote unit. The Remote and Local units communicate video and data information along the
interconnecting cable. Local units offer dual access, allowing the connection of a second user
console close to the computer.
2.2 Glossary
The following terms are used in this guide:
Any Category 5, 5e, 6 or higher cable, solid wires type AWG24.
Keyboard, Video and Mouse.
CATx
KVM
Keyboard, Mouse and Monitor
Console
Dual Access
Singlehead
A system allowing connection of Local and Remote user consoles.
An extender system that supports one monitor + Keyboard/Mouse
An extender system that supports two monitors + Keyboard/Mouse
Dualhead
DVI
Digital Video standard, installed by Digital Display Working Group
3x 1,6 Gbit/sec. Signals are TMDS Level.
The desktop power supply connected to the Local/Remote unit.
PSU
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
CPU with DVI-D
Graphic card
Local Console
Optional
2. Monitor
DVI-D Cat X KVM-
Extender system
Remote Console
Optional
2. Monitor
DVI-D Cat X – KVM Extender system (example)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW
2.3 Features
All members of the DVI-D Cat X - DVI KVM Extender Series offer the following features:
•
•
•
•
Support for DVI-D Graphic cards (all devices)
Support for PS2-Keyboard and PS2-Mouse (ACS1009A and ACS2209A)
Support for USB-Keyboard and USB-Mouse (ACS4001A and ACS4201A)
Maximum resolution: DVI-D: 1600x1200@60Hz over all allowed distances
all lower resolutions with refresh rates of at least 75Hz
•
•
•
•
•
Supporting 18 Bit color depth = 256,000 colors
Status indicator LEDs on each device.
Small footprint chassis.
Rack mount options available.
CPU cables + Adapters included.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
2.4 Product Range
There are four products in the range and various upgrade kits:
DVI-D Cat X - Extender
ACS1009A
ACS2209A
ACS4001A
ACS4201A
KVM-Extender 1x DVI, PS2-Keyboard, PS2-Mouse
(Singlehead)
KVM-Extender 2x DVI, PS2-Keyboard, PS2-Mouse s
(Dualhead)
KVM-Extender 1x DVI, USB-Keyboard, USB-Mouse
(Singlehead)
KVM-Extender 2x DVI, USB-Keyboard, USB-Mouse
(Dualhead)
Upgrade Kits
ACS1009A-RMK
19”/1HE Rackmount- Kit to mount up to 4 Singlehead
devices
ACS2209A-RMK
19”/1HE Rackmount- Kit to mount up to 4 Dualhead
devices
ACS1009A-BP
ACS2209A-BP
Blanking Plate for Single Head Rackmountkit
Blanking Plate for Dual Head Rackmountkit
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW
2.5 Compatibility
Interface Compatibility
•
Digital Video (DVI-D): Digital Video standard, installed by Digital Display Working
3x 1,6 Gbit/sec. Signals are TMDS Level.
•
PS/2 Keyboard: Compatible with all standard keyboards. Certain keyboards with
enhanced features may also be supported with custom firmware.
•
•
PS/2 Mouse: Compatible with all standard 2-button, 3-button and wheel mice.
USB Keyboard: Compatible with all standard keyboards. Certain keyboards with
enhanced features may also be supported with custom firmware. Keyboards with built-in
hub are also supported – but there are never more than two HDI devices supported.
•
USB Mouse: Compatible with all standard 2-button, 3-button and wheel mice.
INFO: devices with USB- connectors do only support Keyboard and
Mouse. It’s possible, that other HDI devices (Human Device Interface) like
Touch-Screen, Graphic tablet, Barcode reader or similar are supported –
but there is no guarantee for this! Regardless of your devices, the extender
will not support more than two devices at once. The DVI-D Cat X KVM-
Extender is NOT suitable for to use with other USB devices like Scanner,
WEB- Cams, data sticks etc.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
2.6 How to Use This Guide
This guide describes the installation and configuration of the DVI-D Cat X – Extender Series.
Although the connection and operation of the system is relatively straightforward, you should
consider the following before getting started:
Connection & Compatibility
If you have purchased an Extender Kit, this will contain all the cables required to connect the
Local unit to your PC or KVM switch. Please see also: Fehler! Verweisquelle konnte nicht
gefunden werden. (page Fehler! Textmarke nicht definiert.)
For information about connection and installation, see Fehler! Verweisquelle konnte nicht
gefunden werden., page Fehler! Textmarke nicht definiert..
DDC Information
Normally it is not necessary to make any adjustments to the DVXi- Extender. However, in
some circumstances, it may be necessary to redefine the source of DDC Information for the
CPU. By default, the DVI-D Cat X KVM-Extender uses its own internal DDC table. If this
setting does not satisfy your requirements, the DDC table can either be switched to the locally
or remotely attached screen.
To modify the DDC-Setup, please ask Technical support for additional information.
Compatibility
Devices with PS2 connectors are NOT compatible to devices with USB connectors.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
3. Installation
For first-time users, we recommend that you carry out a test placement, confined to a single
room, before commencing full installation. This will allow you to identify and solve any
cabling problems, and experiment with the KVM extender system more conveniently.
3.1 Package Contents
You should receive the following items in your extender package (all types):
•
•
•
•
DVI-D Cat X KVM-Extender- pair (Local Unit + Remote Unit)
2x 5V DC universal power supply for the DVI-D Cat X - Extender
2x German type power cord
User manual (Quick Setup)
ACS1009A and ACS2209A (additionally):
•
KVM CPU cable set (1.8m) with one side: PS/2 (6-pin mini-DIN male) keyboard and
mouse connector and DVI-I video (DVI-I dual link male) connector – other side: DVI-I
video (DVI-I dual link male) connector
•
PS2-Keyboard-/ Mouse adapter to connect K/M to the Local Unit (keyboard can be
plugged in directly, without using an adapter)
ACS4001A and ACS4201A (additionally):
•
•
DVI-I (1,8m) video cable (DVI-I dual link male-to-male)
USB (1,8m) cable (USB type A to type B)
ACS2209A and ACS4201A (additionally):
DVI-I (1,8m) video cable (DVI-I dual link male-to-male)
•
If anything is missing, please contact Technical Support (see Appendix F – Calling
Technical Support).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
3.2 Interconnection Cable Requirements
To connect the Local and Remote units you will need:
•
DVI, PS2-Keyboard, PS2-Mouse: Connect the supplied KVM CPU cable set to your
CPU (KVM.- Switch, etc.). Please ensure that the connection is tension-free! Devices
ACS1009A + ACS2209A
•
DVI, USB-Keyboard, USB-Mouse: Connect the supplied KVM CPU cable set to your
CPU (KVM.- Switch, etc.). Please ensure that the connection is tension-free! Devices
ACS4001A + ACS4201A
•
•
DVI: Connect the supplied DVI CPU cable set to your CPU (KVM.- Switch, etc.).
Please ensure that the connection is tension-free! Devices ACS2209A + ACS4201A
CATx Cable: Recommended cable: S/UTP (Cat5) according EIA/TIA 56A, TSB 36 or
Digital STP 17-03170. Four pairs AWG 24. connection according EIA/TIA 568A
(10BaseT). Use of cables from a higher category (Cat5e, Cat6, Cat7) is possible.
The use of unshielded CATx Cable is possible, because of the higher electromagnetic
noise/sensitivity the device class may not be reached.
The use of flexible Cables (Patch cable) Type AWG26/8 is possible. Because of the
higher loss of the stranded cables, the maximum distance is reduced to app. half the
value of solid cables.
A point to point connection is required. Having one or more patch panels
in the line is possible and allowed. Not allowed is a connection from the
CATx link interface (RJ45) to any other products, especially
telecommunications or network equipment.
•
Power Supply
Connect the supplied 5V/DC power supplies to the Plug terminal on the rear of both
Local and Remote units.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
3.3 System Setup
To install your DVI-D Cat X – Extender system:
1. Switch off all devices.
2. Connect your keyboard, monitor(s) and mouse to the Remote unit (depending on device
type). Please ensure, to not swap Mouse- and Keyboard connector. The Keyboard
connector is purple and the Mouse connector is green.
3. Using the supplied CPU KVM cable(s), connect the keyboard, monitor(s) and mouse
connectors on the computer (or KVM switch). Please ensure, to not swap Mouse- and
Keyboard connector. The Keyboard connector is purple and the Mouse connector is
green.
4. Connect the interconnect cable to the INTERCONNECT socket(s)
5. Connect the 5V power supply to power the unit.
Only use the power supply originally supplied with this
equipment or a manufacturer-approved replacement.
6. For a dual access system, connect the keyboard, mouse and monitor for the Local
console to the appropriate ports on the Local unit. The ports may also be used to feed
into a KVM switch. To the local (PS2-) Keyboard-/ Mouse port you can attach a
Keyboard directly or Mouse/ Keyboard together, using the delivered adapter.
7. Power up the system.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
Connect to CPU:
local DVI-Monitor port
Local keyboard/ mouse port
DVI, keyboard, mouse
Connect to Local
console monitor
Solely Keyboard may be
plugged in directly,
keyboard/mouse through
equipped adapter
DVI-D Cat X KVM-Extender Type ACS1009A Local Unit
remote DVI-Monitor
port– connect to
Remote console
monitor
Remote mouse port
Remote keyboard port
DVI-D Cat X KVM-Extender Type ACS1009A Remote Unit
INTERCONNECT – carries video and
data signals – connect to Local/
remote unit with CATx cable
Connect to 5V Power
supply
DVI-D Cat X KVM-Extender Type ACS1009A Local/ Remote Unit
18
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Connect to CPU:
2nd local DVI-Monitor
port Connect to Local
console 2nd monitor
2nd DVI-Graphic card
Connect to CPU:
1st DVI-Graphic card,
keyboard, mouse
local DVI-Monitor port
Connect to Local
console monitor
Local keyboard/ mouse port
Solely Keyboard may be
plugged in directly,
keyboard/mouse through
equipped adapter
DVI-D Cat X KVM-Extender Type ACS2209A Local Unit
2nd remote DVI-Monitor
port Connect to Remote
console 2nd monitor
1st remote DVI-
Monitor port– connect
to Remote console 1st
Remote mouse port
Remote keyboard port
monitor
DVI-D Cat X KVM-Extender Type ACS2209A Remote Unit
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
INTERCONNECT – carries 2nd video –
connect to Local/Remote unit with
CATx cable
INTERCONNECT – carries 1st video
and data signals – connect to Local/
Remote unit with CATx cable
Connect to 5V Power
supply
DVI-D Cat X KVM-Extender Type ACS2209A Local/ Remote Unit
20
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Connect to CPU:
USB
Connect to CPU:
DVI graphic card
local DVI-Monitor port
Connect to Local
console monitor
DVI-D Cat X KVM-Extender Type ACS4001A Local Unit
remote DVI-Monitor
port– connect to
Remote console
monitor
Remote keyboard/mouse
port
DVI-D Cat X KVM-Extender Type ACS4001A Remote Unit
INTERCONNECT – carries video and
data signals – connect to Local/
remote unit with CATx cable
Connect to 5V Power
supply
DVI-D Cat X KVM-Extender Type ACS4001A Local/ Remote Unit
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
2nd local DVI-Monitor
Connect to CPU:
2nd DVI-Graphic card
port Connect to Local
console 2nd monitor
local 1st DVI-Monitor
port Connect to Local
console 1st monitor
Connect to CPU:
USB
Connect to CPU:
1st DVI-Graphic card
DVI-D Cat X KVM-Extender Type ACS4201A Local Unit
2nd remote DVI-Monitor
port Connect to Remote
console 2nd monitor
1st remote DVI-
Monitor port– connect
to Remote console 1st
monitor
Remote keyboard/ mouse
port
DVI-D Cat X KVM-Extender Type ACS4201A Remote Unit
22
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INTERCONNECT – carries 2nd video –
connect to Local/Remote unit with
CATx cable
INTERCONNECT – carries 1st video
and data signals – connect to Local/
Remote unit with CATx cable
Connect to 5V Power
supply
DVI-D Cat X KVM-Extender Type ACS4201A Local/ Remote Unit
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
3.4 Diagnostic LEDs
Each DVI-D Cat X KVM-Extender is fitted with four indicator LEDs: Power, Video OK,
Data Error, Link Status: The Power LEDs are next to the Power socket.
The location of the LEDs is shown below:
Diagnostic LED
Link Status
Diagnostic LED
Data Error
Diagnostic LED
Diagnostic LED
Power
Video OK
Diagnostic - LEDs at DVI-D Cat X - Extender
LED
Appearance
Diagnostics
Off
On
Device not ready
Device ready
Power LED
(Red LED)
Off
On
No or invalid video signal detected
Device ready
Video Okay
(Green LED)
blinking
On
No CAT5 connection
Device ready
Link Status
(Green LED)
Off
Device ready
Data Error
(Green LED)
blinking / On
Errors through data transmission over CAT5 Cable
(Cable too long, too high attenuation or too much
EMI interferences )
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
4. Troubleshooting
There isn’t a picture.
Check the power supply connection at the Local unit. Is the Power (Red LED) at
the Local unit illuminated (see page 24)? If not, the internal power-supply may be
damaged or there may be an internal error.
Check the power supply connection at the remote unit. Is the Power (Red LED) at
the Remote unit illuminated (see page 24)? If not, the internal power-supply may be
damaged or there may be an internal error.
Check that the Interconnection cable is connected at the Local Unit and the Remote
Unit. Is the Link Status LED illuminated (see page 24)? If not, there may be a
problem with the Interconnection cable:
Are there Errors through data transmission over CAT5 Cable (Cable too long, too
high attenuation or too much EMI interferences )? Is the Data Error LED
illuminated or blinking (see page 24)? If yes, check cable length and environment.
Video Okay LED is dark: CPU does not provide a video signal – Check settings of
the graphic card. Try out, connecting a monitor to the local output, to see, whether
ther is a signal or not.
Keyboard
The PC boots fine with no error messages but the keyboard does not work at all
Wrong cable plugged in, keyboard and mouse cables reversed.
Try a different model of keyboard. If the new keyboard works then original one
may be incompatible
Check that the Interconnection cable is connected at the Local Unit and the Remote
Unit. Is the Link Status LED illuminated (see page 24)?
PS2-Mouse
A mouse cursor appears on the screen, but the mouse does not work
Wrong cable plugged in, keyboard and mouse cables reversed.
Try a different model of mouse
The system does not detect a PS/2 mouse, or the application cannot find the mouse.
Wrong cable plugged in, keyboard and mouse cables reversed.
Ensure that the Local Unit is connected to the PC keyboard port to provide power.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
Appendix A: Example Applications
This section illustrates some specific applications using the DVI-D Cat X - Extenders:
•
DVI-D Cat X KVM-Extender with optional, secondary screen.
DVI-D Cat X KVM-Extender with optional, secondary screen
26
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A: EXAMPLE APPLICATIONS
4 CPU’s – local outputs managed through a KVM- Switch and a single console. Remote
Consoles up to 140m away.
•
DVI-D Cat X KVM-Extender – local Consoles through a KVM- Switch
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
Appendix B: Rack Mount Options
DVI-D Cat X KVM- Extender units can be mounted in a 19” rack using the mounting kit:
DVI-D Cat X- Rackmount Kit. Two different versions are available – one each for
Singlehead and for Dualhead devices.
DVI-D Cat X- Rackmount Kit for Singlehead devices consists of:
Base plate
M2,5x5 Philips type
countersunk screws (8x)
M2,5x2 spacer (8x)
19” Rackmount Kit for Singlehead devices (ACS1009A-RMK)
DVI-D Cat X- Rackmount Kit for Singlehead devices consists of:
Base plate
M2,5x5 Philips type
countersunk screws (8x)
M2,5x2 spacer (8x)
n
19” Rackmount Kit for Dualhead devices (ACS2209A-RMK)
To mount a unit:
1. Align the holes on the base plate with the vacant screw holes on the base of the DVI-D
Cat X KVM- Extender unit.
2. Fasten the base of the unit to the plate of the mounting kit using the supplied screws.
Only use the supplied, short screws, to prevent damages on
the PCB’s
3. Close the remaining gaps with blanking plates.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B: RACK MOUNT OPTIONS
The kit allows you to mount a different count of devices
(1…4 devices):
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
Appendix C: Calling Technical Support
If you determine that your DVI-D –Cat X KVM Extender is malfunctioning, do not attempt
to alter or repair it. It contains no user-serviceable parts. Contact Technical Support at Black
Box!
Before you do, make a record of the history of the problem. We will be able to provide more
efficient and accurate assistance if you have a complete description, including:
•
The firmware-revision level printed on the bottom of the Extender (very important,
especially for keyboard and mouse problems); The DVI-D CAT X - KVM extender’s
firmware revision level:
Version Number Format:
Board:
Transceiver:
Keyboard/Mouse:
xxLO/RE Myyy Pzzz Auuu Gvvvvvv
C/M/S xx Pyy Mzz
P/U xx Vyyy
•
•
•
The nature and duration of the problem.
When the problem occurs.
The components involved in the problem—that is, what type of computers, what type of
keyboard, brand of mouse, make and model of monitor, type and make of cable, etc.
•
•
Any particular application that, when used, appears to create the problem or make it
worse.
The results of any testing you’ve already done.
To solve some problems, it might be necessary to upgrade the Extender’s firmware. If this
turns out to be the case for your difficulty, our Technical Support technicians will arrange for
you to receive the new firmware and will tell you how to install it.
Shipping and Packaging
If you need to transport or ship your DVI-D CAT X - KVM Extender:
•
•
Package it carefully. We recommend that you use the original container.
If you are shipping it for repair, please include the Unit’s external power supplies. If you
are returning it, please include everything you received with it. Before you ship the
Extender back to your dealer for repair or return, contact him to get a Return
Authorization (RA) number.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX C: CALLING TECHNICAL SUPPORT
Black Box Technical Support
Country
Web Site/E-Mail
Phone
724-746-5500
Fax
US
724-746-0746
Austria
+43 1 256 98 56
+32 2 725 85 50
+43 1 256 98 56
+32 2 725 92 12
Belgium
Denmark
Finland
France
Germany
Ireland
Italy
+45 56 63 30 10
+358 201 888 800
+33 820 07 09 11
+49 811 5541 110
+353 1 662 2466
+39 02 27 404 700
+31 30 241 7799
+47 55 300 710
+34 916590732
+46 8 44 55 890
+41 55 451 70 71
+44 118 965 6000
+45 56 65 08 05
+358 201 888 808
+33 820 05 07 09
+49 811 5541 499
+353 1 662 2477
+39 02 27 400 219
+31 30 241 4746
+47 55 300 701
+34 916239784
+46 08 38 04 30
+41 55 451 70 75
+44 118 965 6001
Netherlands www.blackbox.nl
Norway
Spain
Sweden
Switzerland www.black-box.ch
UK
31
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
Appendix D: Specifications
Stromversorgung
90-240VAC-0.5A-47-63Hz/5VDC-2000 mA
Voltage
Local Unit : max. 750mA
Remote Unit : max. 750mA
Power required
Interface
(Depending on type of device)
DVI-D up to 1600x1200@60Hz
PS2 or USB (depending on model)
Videoquelle/Monitor
Keyboard
PS2 or USB (depending on model) 2-/3-button and
wheel mouse
Mouse
Maximum Length of Interconnection Cable
120m (400ft)
60m (200ft)
CATx Installation cable AWG24
CATx Patchcable AWG26/8
Type of Interconnection Cable
S/UTP (Cat5) cable acc. EIA/TIA 56A, TSB 36 or
Digital STP 17-03170. Four pairs AWG 24. wiring
acc. EIA/TIA 568A (10BaseT).
CATx Installation cable AWG24
S/UTP (Cat5) cable acc. EIA/TIA 56A, TSB 36 or
Digital STP 17-03170. Four pairs AWG 26/8. wiring
acc. EIA/TIA 568A (10BaseT)..
CATx Patchcable AWG26/8
32
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX D: SPECIFICATIONS
Size and Shipping Weight
103 x 143 x 29mm (4”x5.6”x1.1”) (2 devices)
Weight: 0,6kg (1.3lb) each
DVI-D Cat X
Weight: 1,6 kg (3.5lb)
Shipping box
Environmental
Operating Temperature
Storage Temperature
Relative Humidity
41 to 113°F (5 to 45 °C)
-13 to 140°F (-25 to 60 °C)
max. 80% non-condensing
33
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
Appendix E: Connectors
DVI-D Cat X KVM-Extender Connector Pinouts
DVI-I female connector (Output connector for ALL devices and Input connector
Dualhead devices 2nd Monitor)
1
8 C1 C2
C5
17
24 C3
Pin Signal
Pin Signal
Pin Signal
1
2
3
4
5
6
7
8
T.M.D.S data 2-
T.M.D.S data 2+
9
T.M.D.S data 1-
17
18
19
20
21
22
23
24
T.M.D.S data 0-
T.M.D.S data 0+
T.M.D.S data 0 GND
n.c.
10
11
12
13
14
15
16
T.M.D.S data 1+
T.M.D.S data 1 GND
n.c.
T.M.D.S data 2 GND
n.c.
n.c.
n.c.
n.c.
DDC Input (SCL)
DDC Output(SDA)
Internal use.
+5V high impedance
GND
T.M.D.S clock GND
T.M.D.S clock +
T.M.D.S clock -
Hot Plug recognition
C1 Internal use.
C2 n.c.
C3 Internal use.
C4 Internal use.
C5 GND
34
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX E: CONNECTORS
DVI-I female connector (Input connector for ALL Singlehead devices and Input
connector Dualhead devices 1st Monitor)
DVI-I Buchse (PS2 Singlehead Eingangsbuchse und PS2 Dualhead Eingangsbuchse 1.
Monitor)
1
8 C1 C2
C5
17
24 C3
Pin Signal
Pin Signal
Pin Signal
1
2
3
4
T.M.D.S data 2-
T.M.D.S data 2+
9
T.M.D.S data 1-
17
18
19
20
T.M.D.S data 0-
10
11
12
T.M.D.S data 1+
T.M.D.S data 0+
T.M.D.S data 0 GND
T.M.D.S data 2 GND
PS2-KBD CLK
T.M.D.S data 1 GND
PS2-MOUSE CLK
PS2-MOUSE VCC-IN +5V
(not required)
5
PS2-KBD DATA
13
PS”-MOUSE-DATA
21
PS2-KBD VCC-IN +5V
(always required)
6
7
8
DDC Input (SCL)
DDC Output(SDA)
Analog VSYNC
14
15
16
+5V In for DDC
GND
22
23
24
T.M.D.S clock GND
T.M.D.S clock +
T.M.D.S clock -
Hot Plug recognition
C1 n.c.
C2 n.c.
C3 n.c.
C4 n.c.
C5 GND
35
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI-D CAT X KVM-EXTENDER
Combined Keyboard/Mouse connector (output connector Local Unit)
Pin
1
2
3
4
5
6
KBD-DATA
MOUSE-DATA
KBD/MOUSE-GND
VCC (+5V)
KBD-CLK
MOUSE-CLK
Keyboard/Mouse connector (output connector Remote Unit)
Pin Keyboard
Pin Mouse
1
2
3
4
5
6
KBD-DATA
1
2
3
MOUSE-DATA
KBD-GND
VCC (+5V)
KBD-CLK
MOUSE-GND
VCC (+5V)
4
5
MOUSE-CLK
6
36
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX E: CONNECTORS
Keyboard/Mouse Adapter to connect Keyboard/Mouse to Local Unit
Pin Connector (device)
Pin Keyboard
Pin Mouse
1
2
3
4
5
6
KBD-DATA
MOUSE-DATA
KBD-GND
1
2
3
KBD-DATA
2
1
3
MOUSE-DATA
KBD -GND
VCC (+5V)
KBD -CLK
MOUSE-GND
VCC (+5V)
VCC (+5V)
4
5
4
6
KBD-CLK
6
5
MOUSE-CLK
MOUSE-CLK
Power
Pin
Signal
+5V
inner
outer
GND
37
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
|