Black Box Switch 4 x 1 DVI and Audio Switch User Manual

4 x 1 DVI and Audio Switches  
Chapter 4: Operation/Chapter 5: IR Remote Control  
Chapter 5: IR Remote Control/Chapter 6: Serial Control  
AVSW-DVI4X1  
4. Operation  
1
5
9
2
6
3
7
4
8
LED Indicator  
The Power LED turns green when the video switch is powered on. When a video port  
is selected, its corresponding Port LED turns yellow.  
10  
14  
11  
15  
12  
16  
4 x 1 DVI and Audio Switch  
13  
SHIFT  
VIDEO  
AUDIO  
Push Button  
ON/OFF  
ON/OFF  
RESOURCES  
14  
13  
15  
16  
Send up to four source inputs  
for screen output to one display.  
Press the corresponding button to select a port.  
Function button  
The Function button adjust the optimal video strength corresponding to the length and  
quality of DVI cable.  
Figure 5-1. Remote control.  
To adjust the video signal strength, follow these steps:  
1. Press the Function button three times.  
6. Serial Control  
The DVI and audio switches’ built in serial interface enables users to control the switch via a PC,  
serial controller devices, or home theater system. The controllers serial port should be configured  
as shown in Table 6-1.  
2. Press Push button #1 one or two times to adjust the selected port’s input video strength.  
One beep = Normal or two beeps = Enhance.  
Table 6-1. Serial parameters settings.  
or  
Press Push button #3 one or two times to adjust the selected port’s output current.  
One beep = Normal or two beeps = Enhance.  
Parameter  
Baud Rate  
Data Bits  
Parity  
Setting  
9600  
8
or  
Press Push button #4 one, two, or three times to adjust the selected port’s output emphasis.  
One beep = no pre-emphasis, two beeps = low pre-emphasis, three beeps = medium pre-  
emphasis, or four beeps = high pre-emphasis.  
None  
1
Stop Bits  
3. Once the setting is finished, press the Function button one time to exit the setting.  
Flow Control None  
5. IR Remote Control  
The remote control operates within a 1.5-ft. (5-m) range of the DVI switch. To select a source  
device with a remote control, press the number button (1–4 or 1–8) to directly switch to the  
corresponding port.  
To select a source device via serial interface, select the number that corresponds to the port.  
For example, send “1” to switch to Port 1.  
© Copyright 2013. Black Box Corporation. All rights reserved. Black Box® and the Double Diamond  
logo are registered trademarks of BB Technologies, Inc. Any third-party trademarks appearing in  
this manual are acknowledged to be the property of their respective owners.  
NOTES:  
1. Remove the battery protector on the remote control before operation.  
2. On the remote control, only buttons 1–4 are activated. The rest of the buttons are reserved  
for other models.  
AVSW-DVI4X1, version 2  
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.  
Customer  
Support  
Information  
call 724-746-5500) FREE technical support 24 hours a day, 7 days a  
week: Call 724-746-5500 or fax 724-746-0746 Mailing address:  
Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018  
FREE! Live, 24/7 Tech Support is just 30 seconds away.  
724-746-5500  
|
blackbox.com  
Page 5  
Page 6  
AVSW-DVI4X1  
AVSW-DVI4X1  
724-746-5500 | blackbox.com  
Chapter 2: Overview  
724-746-5500 | blackbox.com  
Chapter 1: Specifications/Chapter 2: Overview  
Chapter 2: Overview  
Chapter 3: Installation  
Table 2-1. 4X1 DVI and Audio switch components.  
1. Specifications  
3. Installation  
2.2 What’s Included  
4 x 1 DVI and Audio Switch (AVSW-DVI4X1):  
• Video switch  
Enclosure — Metal  
• Before installation, power off all devices that will be connected to this system.  
• Make sure that all devices you will connect are properly grounded.  
Number in  
Fig. 2-1  
Maximum Video Resolution — Full HD 1080p (1920 x 1080), WUXGA (1920 x 1200)  
Number of DVI Inputs — (4)  
Component  
Description  
• Place cables away from fluorescent lights, air conditioners, and machines that are likely  
to generate electrical noise.  
• (1) DB9 F to ear jack cable, 3.8-ft. (1.2-m)  
• Rear bracket  
On Yellow when port 1–4 is selected.  
Off when port 1–4 is not selected.  
1
(4) Input LED indicators  
Remote Control Support — Yes  
NOTE: If no screen displays, follow these steps:  
Serial Control Support —Yes  
• Screw kit  
1. Make sure the device cables are correctly and firmly attached.  
2. Set your display device’s input source as DVI.  
On Green when power to the unit is on.  
User Controls — (1) Function button, (4) port selection buttons  
• Foot pad  
2
3
(1) Power LED indicator  
(4) Push buttons  
Off when power to the unit is off.  
Connectors — Input: (4) DVI (digital only), (4) audio jacks;  
• IR remote controller  
• Power supply and power cord  
• This user manual  
Output: (1) DVI (digital only), (1) audio jack  
3. Check the PC BIOS configuration for the video output settings.  
4. Connect your computer to the display DIRECTLY to check if the video signal gets through.  
Installation Steps  
Press buttons 1–4 to select a port.  
Indicators — (5) LEDs: (1) dual-color for Power and Video,  
(4) LEDs for video input  
4
(1) Audio port (Output)  
(4) Audio ports (Input)  
(1) Video port (Output)  
(4) Video ports (Input)  
(1) Function button  
(1) Serial port  
Connects to a speaker.  
Optional:  
Power — Consumption: 4.5 W  
1. Use a video cable (DVI) to connect the display to the video output port on the back of the  
switch. Plug a set of audio jacks from the speaker to the switch’s speaker port.  
• Audio cable  
5
Connect to audio sources 1–4.  
Connects to a display.  
Size — 1.3"H x 8.7"W x 3.9"D (3.4 x 22 x 10 cm)  
2. Use a video cable (DVI) to connect the source device to the video input port on the switch.  
Use an audio cable to connect the speaker port from the input side of the switch to the  
corresponding output port on the source device.  
6
2. Overview  
2.1 Features  
2.3 Hardware Description  
7
Connect to video sources 1–4.  
Adjusts the video signal strength.  
Connects to a computer for serial control.  
Applies power to the unit.  
Figure 2-1 shows the front and back panels of the AVSW-DVI4X1. Table 2-1 describes its  
3. Plug the power supply into the switch and power on the switch.  
8
components.  
• Select (1) DVI + Audio from (4) DVI + Audio sources.  
• Control via front-panel push buttons, IR remote control, or serial control.  
4. Turn on the display (monitor, projector, or TV) and then power on the source device(s).  
1 3 1 3 1 3 1 3  
9
4
X
1
D
V
I
S
w
i
t
c
h
w
i
t
h
A
u
i
d
o
• Function button adjusts the optimal video signal strength corresponding to the length  
or quality of DVI cable.  
10  
Power supply  
2
4
8
1
2
3
4
• LED shows the active status of DVI + Audio sources.  
• HDTV compatible.  
5
OUTPUT  
4
3
2
1
• Protects content via HDCP.  
• Supports up to Full HD 1080p/1920 x 1200 resolution.  
10  
9
6
7
• Compatible with most of the popular screen resolutions to XGA, SXGA, UXGA, WSXGA,  
Full HD, WUXGA system.  
Figure 2-1. 4X1 DVI and Audio switch front and back panels.  
Page 1  
Page 2  
Page 3  
Page 4  
AVSW-DVI4X1  
AVSW-DVI4X1  
AVSW-DVI4X1  
AVSW-DVI4X1  
724-746-5500 | blackbox.com  
724-746-5500 | blackbox.com  
724-746-5500 | blackbox.com  
724-746-5500 | blackbox.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Decker Saw 3009 User Manual
Blaupunkt Car Stereo System MIAMI 100 User Manual
Blomberg Refrigerator KQD 1360X User Manual
Bloomfield Beverage Dispenser 9456 User Manual
Boca Research Printer FSP 42 User Manual
Bose Car Amplifier 1800 VI User Manual
Breville Water Dispenser AF5 User Manual
Brother Label Maker PT E300 User Manual
Bryant Furnace 373LAV User Manual
Cadillac Automobile 2007 Escalade EXT User Manual