the “UTP 10/UTP 100” switch determines the speed
of operation for the UTP port. When set to “UTP 100”
(factory setting), the UTP port will operate at 100 Mbps.
When set to “UTP 10” the UTP port will operate at
10 Mbps. Adjust the 10/100 Mbps switch to the speed
of the connecting device and check for link status.
a Listed Direct Plug-In Power Unit marked “Class 2”
and rated at 9VDC, 1 Amp.
2. This product should always be used only with the
Supplied Power Unit.
Overview and Description:
The FlexPoint 10/100 converts between Fast Ethernet
fiber 100Base-Fx and 10Base-T or 100Base-Tx twisted
pair (RJ45 UTP) cabling. It operates in half duplex
(HD) or full duplex (FD).
WARNING!
Before inserting the Power Adapter, verify
that the power on the unit is appropriate
The following FlexPoint 10/100 models are described here:
“UTP Full Duplex/UTP Half Duplex” Switch:
LMC100A-SC-R2
LMC100AE-SC-R2
LMC100A-SMSC-R2
LMC100AE-SMSC-R2
LMC100A-R2
LMC100AE-R2
LMC100A-SM-R2
LMC100AE-SM-R2
LMC100A-RJ-R2
LMC100AE-RJ-R2
Model
Fiber Type
Distance
When the “Auto/Manual” switch is in “Manual” position,
the “UTP Full Duplex/UTP Half Duplex” switch
determines the duplex operation mode for the UTP
port. When set to “Full Duplex” (factory setting), the
UTP port will operate in full duplex. When set to “Half
Duplex” the UTP port will operate in half duplex. Adjust
the half/full-duplex switch to accommodate the
connecting device and check for link status.
for yourAC line voltage source.
LMC100A-SC-R2
LMC100AE-SC-R2
LMC100A-SMSC-R2
LMC100AE-SMSC-R2
LMC100A-R2
LMC100AE-R2
LMC100A-SM-R2
LMC100AE-SM-R2
LMC100A-SMSC-LH-R2 1310nm, SM, SC
LMC100AE-SMSC-LH-R2 1310nm, SM, SC
LMC100A-RJ-R2
LMC100AE-RJ-R2
1310nm, MM, SC
1310nm, MM, SC
1310nm, SM, SC
1310nm, SM, SC
1310nm, MM, ST
1310nm, MM, ST
1310nm, SM, ST
1310nm, SM, ST
2km/1.2mi.
2km/1.2mi.
28km / 17.4 mi.
28km / 17.4 mi.
2km/1.2mi.
2km/1.2mi.
28km / 17.4 mi.
28km / 17.4 mi.
58km/35mi.
58km/35mi.
LMC100A-SMSC-XLH-R2
LMC100AE-SMSC-XLH-R2
LMC100A-SMRJ-R2
LMC100AE-SMRJ-R2
LMC100A-SMSC-SLH-R2
LMC100AE-SMSC-SLH-R2
Mounting and Cable Attachment:
The FlexPoint 10/100 can be solo-mounted using a
wall-mounting kit, or rack-mounted using a 5-position shelf
or a high-density 14-unit FlexPoint Powered Chassis.
Attach the FlexPoint 10/100 UTP via a category 5
cable to a 10Base-T or 100Base-Tx Ethernet device.
Attach the FlexPoint 10/100 fiber via cable to a 100Base-Fx
Fast Ethernet device. The FlexPoint transmit (Tx)
must attach to the receive side on other device; the
receive (Rx) must attach to the transmit.
Half duplex must be used when connecting to a hub.
Full duplex should be used when connecting switches
or between a switch and a full-duplex workstation.
LMC100A-SMSC-LH-R2 LMC100A-LC
LMC100AE-SMSC-LH-R2
LMC100AE-LC
LMC100A-SMLC
LMC100AE-SMLC
1310nm, MM, MTRJ 2km/1.2mi.
1310nm, MM, MTRJ 2km/1.2mi.
“Fiber Full Duplex/Fiber Half Duplex” Switch:
Since the IEEE 802.3 standard defines the Ethernet
10Base-FL fiber differently than the Fast Ethernet
100Base-Fx, it should be noted that they are
incompatible. The FlexPoint 10/100 supports 100Base-Fx
only. It operates in a half- or full-duplex mode of
operation. This switch controls the half/full-duplex
operation of the fiber port.
Switch Settings:
“RJ45 Cross-Over” Switch:
When connecting the UTP to a hub or switch, set
switch to “Straight-Through” (factory setting). When
connecting to a workstation, set it to “Cross-Over.”
LMC100A-SMSC-XLH-R2 1550nm, SM, SC
LMC100AE-SMSC-XLH-R2 1550nm, SM, SC
85km / 52.8 mi.
85km / 52.8 mi.
LMC100A-SMRJ-R2
LMC100AE-SMRJ-R2
1310nm, SM, MTRJ 28km / 17.4 mi.
1310nm, SM, MTRJ 28km / 17.4 mi.
FlexPoint™ 10/100
LMC100A-SMSC-SLH-R2 1550nm, SM, SC
LMC100AE-SMSC-SLH-R21550nm, SM, SC
110km/68mi.
110km/68mi.
2km/1.2mi.
2km/1.2mi.
28km/17.4mi.
28km/17.4mi
“UTP Auto/UTP Manual” Switch:
LMC100A-LC
1310nm, MM, LC
1310nm, MM, LC
1310nm, SM, LC
1310nm, SM, LC
CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S.: Call 877-877-BBOX
(outside U.S. call 724-746-5500)
Half duplex should be used when connecting to a hub
(with a shared/non-switched fiber port) or a workstation
that supports only half-duplex. Full duplex can be
used when connecting to a switch or a workstation
that supports full-duplex operation.
Setting the switch to “Auto” (factory setting) enables the
UTP port to determine the speed and duplex mode
automatically. If the connected device cannot provide the
proper signal to indicate its own mode of operation, the
“Manual” switch should be used. This feature allows
connections with devices that do not auto-negotiate properly.
LMC100AE-LC
LMC100A-SMLC
LMC100AE-SMLC
FREE technical support 24 hours a day, 7 days
a week; Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation,
1000 Park Drive, Lawrence, PA 15055-1018
Installation and Configuration:
Power Adapter Notice:
1. When Using in a stand-alone configuration, this
product is intended to be and must be used only with
©Copyright 2011. Black Box Corporation. All rights reserved.
Web site: www.blackbox.com
E-mail: [email protected]
“UTP 10/UTP 100” Switch:
When the “Auto/Manual” switch is in “Manual” position,
1000 Park Drive · Lawrence, PA 15055-1018
724-746-5500 · Fax 724-746-0746
LED Indicators:
LED
TRADEMARKS USED IN THIS MANUAL
NORMAS OFICIALES MEXICANAS (NOM)
ELECTRICAL SAFETY STATEMENT
1. Todas las instrucciones de seguridad y operación deberán
ser leídas antes de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser
guardadas para referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus
instrucciones de operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—
por ejemplo, cerca de la tina de baño, lavabo, sótano mojado
o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos
o pedelstales que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo
sólo como sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al
equipo eléctrico más allá a lo descrito en las instrucciones
de operación. Todo otro servicio deberá ser referido a
personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su
posición no interfiera su uso. La colocación del aparato
eléctrico sobre una cama, sofá, alfombra or superficie
similar puede bloquea la ventilación, no se debe colocar
en libreros o gabinetes que impidan el flujo de aire por
los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de
fuentes de calor como radiadores, registros de calor,
estufas u ostros aparatos (incluyendo amplificadores) que
producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de
poder sólo del tipo descrito en el instructivo de operación,
o como se indique en el aparato.
12. Precación debe ser tomada de tal manera que la tierra fisica
y la polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal
manera que no sean pisados ni pellizcados por objetos
colocados sobre o contra ellos, poniendo particular
atención a los contactos y receptáculos donde salen del
aparato.
14. El equipo eléctrico debe ser limpiado únicamente de
acuerdo a las recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada
lejos de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando
el equipo no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos
liquidos no sean derramados sobre la cubierta u orificios
de ventilación.
Black Box and the Double Diamon logo are registered trademarks of
BB Technologies, Inc. Any other trademarks mentioned in this manual
are acknowledged to be the property of the trademark owners.
Color
Yellow
Description
Power:
Power applied
UTP Auto:
UTP FDx:
UTP Link:
UTP 10:
UTP 100:
Fiber FDx:
F/O Link:
Green
Green
Green
Yellow
Green
Green
Green
Auto-Negotiation enabled
Full-Duplex detected
Link / Data received
10 Mbps link detected
100 Mbps link detected
Full-Duplex selected
Link / Data received
FEDERALCOMMUNICATIONS COMMISSIONAND
CANADIAN DEPARTMENT OFCOMMUNICATIONS
RADIO FREQUENCYINTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used properly, that
is, in strict accordance with the manufacturer’s instructions,
may cause interference to radio communication. It has been
tested and found to comply with the limits for a Class A
computing device in accordance with the specifications in
subpart J of Part 15 of FCC rules, which are designed to
provide reasonable protection against such interference when
the equipment is operated in a commercial environment.
Operation of this equipment in a residential area is likely to
be cause interference, in which case the user at his own
expense will be required to take whatever measures may be
necessary to correct the interference.
SPECIFICATIONS:
ꢀ
ꢀ
Protocol:
IEEE 802.3
Connectors & Cables:
Twisted Pair UTP:
Fiber:
18. Servicio por personal calificado deberá ser provisto
cuando:
RJ45, Category 5 or higher
SC, ST or MT-RJ
50/125, 62.5/125, 100/140μm
9/125μm
Half-Duplex Full-Duplex
100m/328ft. 100m/328ft.
412m/1,350ft. 2km/1.2mi.
412m/1,350ft. 28km/16.8mi.
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro
del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un
cambio en su desempeño; o
Multimode:
Single-mode:
ꢀ
Supported Distances:
Twisted PairUTP:
MM 1310nm fiber:
SM 1310nm fiber:
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
E: El aparto ha sido tirado o su cubierta ha sido dañada.
SM 1310nm LH fiber: 412m/1,350ft. 58km/36mi.
SM 1310nm XLH fiber: 412m/1,350ft. 85km/52.8 mi.
SM 1310nm SLH fiber: 412m/1,350ft. 110km/68.4 mi.
This digital apparatus does not exceed the Class A limits
for radio noise emission from digital apparatus set out in
the Radio Interference Regulation of the Canadian
Department of Communications.
ꢀ
ꢀ
ꢀ
ꢀ
Dimensions / Weight:
Power:
Temperature:
Humidity:
W:3.0”xD:4.0”xH:1.0” / 6oz.
9VDC/500mA or 5VDC/750mA
0 to 40 degrees C
Le présent appareil numérique n’émet pas de bruits
radioélectriques dépassant les limites applicables aux
appareils numéirques de las classe A prescrites dans le
Règlement sur le brouillage radioélectrique publié par le
ministère des Communications du Canada.
0-90% (non-condensing)
LMC100A-SC-R2, version 2
040-01009-R21B 3/11
Download from Www.Somanuals.com. All Manuals Search And Download.
|