™
ReadyDry
U S E R ’ S G U I D E
79T3 SERIES 220-240v
3
4
5
Safety Instructions
Product view
Assembly
6
Special Features
Operation
7-10
Maintenance and Care
10-11
Troubleshooting
12
13
Consumer Services
14 Replacement Parts
14 Formulas
15 Additional Accessories
16 Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
■
When using an electrical appliance, basic
precautions should be observed, including
the following:
Not intended for use by persons (including
children) with reduced sensory or mental capabilities,
or lack of experience and knowledge, unless they
have been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety
Young children should be supervised to ensure
that they do not play with the appliance
Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, petrol, etc.)
Do not modify the Earthed plug
Do not use for any purpose other than described
in this User’s Guide
Use only manufacturer’s recommended
attachments
Use only cleaning products formulated by
BISSELL for use in this appliance to prevent
internal component damage
READ ALL INSTRUCTIONS
BEFORE USING YOUR
CARPET WAShER.
■
■
Always connect to a properly Earthed
outlet. Unplug from outlet when not in
use and before conducting
■
■
maintenance or troubleshooting.
■
■
WARNING:
Use indoors only
To reduce the
risk of fire, electric shock, or injury:
■
■
■
■
■
■
Keep openings free of dust, lint, hair, etc.
Keep appliance on a level surface
Turn off all controls before unplugging
Be extra careful when cleaning stairs
Pay close attention when working
around children
■
Do not immerse; use only on surfaces moistened
by cleaning process
■
Do not leave machine when it is plugged in
■
Do not service machine when it is plugged in
■
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent in order
to avoid a hazard
SAvE ThESE
■
Do not use machine if it has been dropped,
damaged, left outdoors or dropped into water
■
INSTRUCTIONS.
Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around sharp
corners or edges, run appliance over cord, or
expose cord to heated surfaces
ThIS moDEL IS foR hoUSEhoLD USE oNLY.
■
WARNING:
This appliance must
Do not carry the appliance while in use
Do not unplug by pulling on cord; unplug by
grasping plug not the cord
be Earthed
.
■
■
Do not handle plug or appliance with wet hands
Do not put any object into appliance openings, use
with blocked opening or restrict air flow
Do not expose hair, loose clothing, fingers or body
parts to openings or moving parts
Do not pick up hot or burning objects
Do not pick up flammable or combustible
materials (lighter fluid, petrol, kerosene, etc.) or use
in the presence of explosive liquids or vapours
Do not use appliance in an enclosed space filled with
vapours given off by oil base paint, paint
thinner, some moth proofing substances,
flammable dust, or other explosive or toxic vapours
Remove plug from electrical outlet before cleaning
or maintaining the appliance
IMPORTANT
foR oPERATIoN oN
A 220-240 VoLT A.C. 50/60 hz PoWER
SUPPLY oNLY.
■
■
If your appliance is fitted with a nonrewireable
BS 1363 plug it must not be used unless a 13
amp (ASTA approved to BS 1362) fuse is fitted in
the carrier contained in the plug. Spares may be
obtained from your BISSELL supplier. If for any
reason the plug is cut off, it must be disposed
of, as it is an electric shock hazard should it be
inserted into a 13 amp socket.
■
■
■
■
3
w w w . b i s s e l l . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Product view
Spray Trigger
Power Switch
Quick Release™
Cord Wrap
Tough Stain Tool
Hose Secure Latch
Upper Hose Wrap
Power Cord
Handle Assembly
Ready-to-Use Hose
Easy Carry
Handle
Clean Water/
Formula Tank
Oxy Gen2™
PowerTool
Large,
Easy-To-Maneuver
Wheels
Lower Body
Assembly
Handle Release
ReadyTools™
Dial
Dirty Water
Tank
WARNING:
To reduce the risk of fire and electric
shock due to internal component damage, use
only BISSELL cleaning formulas intended for
use with the carpet washer. Non-BISSELL
cleaning solutions may harm the machine
and void the warranty.
PowerRoller
Cleaning formula
™
Keep plenty of genuine BISSELL Fiber Cleansing Formula on hand so you can wash and protect
whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas. Non-BISSELL
cleaning solutions may harm the machine and will void the warranty.
BISSELL
BISSELL
BISSELL
BISSELL
BISSELL
BISSELL
BISSELL
Fiber Cleansing
Formula™ with
Scotchgard™
Protector
Multi- Allergen
Pet Odor and
Natural Orange
Extract Formula
with Scotchgard™
Protector
Tough Stain
Lavender Essence Oxy Gen2
Formula with
Removal™ Formula Soil Removal™
with Scotchgard™ Formula with
Pre-cleaner™
Scotchgard™
Protector
Scotchgard™
Protector
Protector
4
w w w . b i s s e l l . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
how to use this guide
WARNING:
Do not plug in your carpet
washer until you have
completely assembled it
per the following instructions
and are familiar with all
instructions and operating
procedures.
This user’s guide has been designed to help
you get the maximum satisfaction from your
ReadyDry carpet washer. You’ll find assembly
and operating instructions, safety precautions,
as well as maintenance and troubleshooting
instructions. Please read this user’s guide
thoroughly before assembling your carpet
washer.
Your carpet washer comes in three easy to
assemble components:
Tip: Regular carpet cleaning
can reduce dust and allergens in
your home.
• Handle assembly
• Upper hose wrap
• Lower body assembly
Four Phillips head screws are included and can
be found taped to the handle assembly.
1.
Assembly
The only tool you will need to assemble your
ReadyDry is a Phillips head screwdriver.
1. Slide upper handle into lower body assembly
and secure with 2 screws.
2a.
2. Attach upper hose wrap using 2 screws.
3. Wrap hose clockwise around the upper and
lower hose wraps as shown on page 4. Be
sure to properly secure grip into the notched
holder.
4. Keep hose locked in place with the
secure latch.
5. Wrap the power cord as shown on page 4.
2b.
Upper Hose
Wrap Screws
6. Place Oxy Gen2 PowerTool in the center tool
caddy and the tough stain tool on the hose
wand.
Upper Handle
Screws
5
w w w . b i s s e l l . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Special features of your BISSELL ReadyDry
Your BISSELL ReadyDry carpet washer is a
home cleaning system that uses a combination
of hand hot tap water, BISSELL advanced cleaning
formula, the innovative PowerRoller and suction
to safely wash carpet and area rugs.
WARNING:
Toreduce the riskoffire,use only
BISSELL advanced deep cleaning
formula for full size machines in your
carpet washer. Use of cleaning
PowerRoller
formulas that contain lemon or
pine oilmaydamage thisappliance
andvoidthe warranty.Chemical
spotcleanersorsolvent-basedsoil
removersshouldnotbe used.These
productsmayreactwiththe plastic
materialsusedinyourcarpetwasher
causing cracking or pitting.
The PowerRoller is designed for great cleaning
performance with fast drying results. It traps, lifts
and removes dirt and debris. Unlike
traditional carpet washers, where cleaning
solution is sprayed directly into the carpet, the
PowerRoller absorbs the majority of the spray
from the machine, meaning your carpet and
area rugs get cleaned and revitalized, while still
allowing you to get back on them in less than 30
minutes. When in the upright position for storage
or tool use, the PowerRoller is lifted off the floor
surface and held in place. This will also help the
PowerRoller dry between uses. The PowerRoller
can be washed or replaced as needed.
ReadyTools™ Dial
The ReadyTools feature allows you to choose
between FLOOR CLEANING or cleaning with TOOLS
simply by turning the dial. The TOOLS setting
allows for above floor cleaning of upholstery,
stairs, creases along baseboards and other hard
to reach areas. Simply choose the tool that is
appropriate for the job, attach it to the flexible
hose and you are ready to go.
Oxy Gen2 PowerTool
The Oxy Gen2 PowerTool is an advanced stain
fighting tool. By adding Oxy Gen2 multi-purpose
formula to the tool, tough stains such as coffee,
juice, cola and red wine are easier to clean up.
The tool can store ready to use with the
Oxy Gen2 formula in it.
Easy carry handle
Located in the back of the machine,the easy carry
handle makes it easy to carry the machine.Refer to
page 4 for location.
6
w w w . b i s s e l l . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Before you clean
1. If desired, move furniture to another area if
cleaning an entire room.
2. vacuum area with a dry vacuum cleaner
before cleaning.
EXIT
9
0
1
2
1
3. Plan your cleaning route to leave an exit
path. It is best to begin cleaning the corner
farthest from your exit.
7
6
5
'
3
1
AR
ST
T
R
E
2
E
H
3
'
4
4
Fill the clean water/formula tank
1. Remove the clean water/formula tank from the
base of the machine by pulling up and out from
the back. You can also detent the handle and
pull the tank straight up if you desire.
2. Unscrew the black cap and red insert. Remove
and set aside.
3. Fill the tank up to the FILL LINE with hand
hot tap water.
4. Add 3 ounces of formula (always use
genuine BISSELL formulas to maximize
cleaning and for the safety of your machine).
5. Replace the cap and insert and tighten by
turning clockwise.
6. Replace the clean water/formula tank back
into the machine. Be sure that the cap is
seated in the receiver.
Carpet washing
1. Make sure the ReadyTools Dial is in the
FLOOR CLEANING position.
2. Plug the ReadyDry into the proper outlet and
turn the power on using the switch in the
back.
3. With your foot, press the gray handle release
lever located on the back of the unit. Take
care to notice the way the machine floats
forward.
4. While pressing the spray trigger make one
forward wet pass and another one back.
Repeat once and move on to the next
section of carpet or area rug to be washed.
Take care not to run over loose objects of
the edges of area rugs.
Tip:
Thorough vacuuming
before carpet washing will prevent
early clogging of the lint screen.
7
w w w . b i s s e l l . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Empty the dirty water tank
1. When the dirty water tank level reaches the FULL line,
when the float trips or when finished carpet washing,
turn power switch off.
WARNING:
To reduce the risk of fire
and electric shock due to
internal component
2. Remove dirty water tank by lifting straight up.
Carry it to the sink or wherever you plan to
dump the dirty water.
damage, use only BISSELL
cleaning fluids intended for
use with the carpet washer.
Non-BISSELL cleaning
solutions may harm the
machine and void
3. Remove the tethered cap on the rear of
the tank.
4. Pour out the dirty water, rinse tank and replace
the warranty.
the cap.
5. To continue carpet washing refer back to page
7 and begin with "Fill the clean water/formula
tank."
If carpet washing is complete, refer to the
“Maintenance and care” section on page 11.
Pretreating (optional)
1. Pretreating (optional)
Pretreating is recommended to improve cleaning
effectiveness for heavily soiled carpet in high traffic
areas such as entry ways and hallways. Please keep
in mind that pretreating will wet the carpet and could
impact dry time.
To pretreat:
A. Using the BISSELL Tough Stain
Pre-cleaner, generously spray evenly over
soiled area, do not overwet.
B. Wait 3-5 minutes before carpet washing.
C. Clean as normal using your BISSELL ReadyDry,
following the instructions on page 7.
™
ReadyTools (cleaning with attachments)
Your ReadyDry carpet washer comes equipped
with a hose and at least two attachments for
cleaning stairs, upholstery, stains and more.
Important! If using the machine to clean
upholstery, check upholstery tags.
1. Check manufacturer’s tag before cleaning. “W”
or “WS” on the tag means you can use your
ReadyDry. If the tag is coded with “X” or “S”
(with a diagonal strike through), or says “Dry
Clean Only,” do not proceed. Do not use on
velvet or silk. If manufacturer’s tag is missing
or not coded, check with your furniture dealer.
Manufacturer’s tag
w w w . b i s s e l l . c o m
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
ReadyTools™ (continued)
2. Check for colorfastness in an inconspicuous
place.
3. If possible, check upholstery stuffing.
Colored stuffing may bleed through fabric
when wet.
4. Plan activities to give upholstery time to dry.
5. Vacuum thoroughly to pick up loose debris and
pet hair. Use a vacuum with a brush attachment
and a crevice tool to clean in fabric folds and tufts.
6. To start cleaning with attachments, follow
the instructions on page 7, beginning with
"Fill the clean water/formula tank".
7. Set the ReadyTools dial to the TOOLS setting.
This will allow for suction from the hose.
8. Attach the desired cleaning tool to the end of
the hose.
9. Clean by pressing the spray trigger to spray
cleaning solution onto the area to be
cleaned. Slowly move the tool back and forth
over the soiled surface. Release the spray
trigger to suction dirty water. Continue to
clean in the area, working in small sections,
until dirt is removed.
Caution: Do Not Overwet.
10. When finished cleaning, remove and rinse
the tool(s) in clean, running water.
11. It is recommended that you suction clean
water from the tap to rinse out the hose.
12. Before wrapping hose onto tool rack, lift end
of hose and stretch out to ensure all water is
cleared from hose.
13. Wrap hose around tool rack.
14. Empty dirty water tank and rinse out,
following instructions on page 8.
15. If the ReadyTools dial becomes difficult to
turn, the diverter assembly that holds the dial
may need to be cleaned. To clean, flush hot
water through the nozzle. Make sure the dial
is set to FLOOR CLEANING.
9
w w w . b i s s e l l . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Oxy Gen2™ PowerTool
To use the Oxy Gen2 PowerTool:
1. Pull out the rubber stopper in the tank.
2. Fill with Oxy Gen2™ formula.
3. Replace the rubber stopper and attach the
Rubber Stopper
tool to the hose grip.
4. Refer to page 9 “ReadyTools” steps 9-10.
Maintenance and care
Machine care
For best results, a few simple steps can assure
your carpet washer is well maintained after your
cleaning is complete.
Lint Screen
1. Turn power switch off. Unplug the machine
and wrap the power cord.
2. After emptying the dirty water tank, rinse it
with running hand hot tap water, taking care
to clean all around the interior.
3. If necessary, check and clean out the lint screen
after each use by wiping clean any visible residue.
4. Replace the dirty water tank back into the machine.
5. Any loose hair or debris can be pulled from
the PowerRoller and thrown away.
6. To clean the attachments, remove from hose
and rinse in clean, running water. Dry before
storing. Clean the hose by suctioning clean
water from the tap. Before wrapping back on
machine, lift end of hose and stretch out to
ensure all water is cleared from hose.
7. Wipe the machine’s exterior with a soft cloth.
8. Machine Storage: Allow PowerRoller to dry
completely before storing. Put the unit away
in a closet or basement for the next use.
Store in a protected, dry area. Since this
product uses water, it must not be stored
where there is a danger of freezing. Freezing
will damage internal components and void
the warranty.
w w w . b i s s e l l . c o m
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Cleaning/replacing the PowerRoller
1. Turn power switch to off and unplug the
machine.
3.
2. Remove both tanks, detent the handle and
turn the machine on its back.
3. Remove the 6 screws from the sole plate
using a Phillips head screwdriver.
4. Turn the machine on its side so the cord side
is facing up.
5. Remove the the swing arm (with dowel) and
roller assembly.
5.
6. Slide the PowerRoller up off the dowel and
replace as desired.
7. To replace, slide the PowerRoller onto the
metal dowel and place the end with the
taller cog down into the lower swing arm.
Ensure the dowel is seated and that the
belt is around the roller cog. Place the other
swing arm in position and push the roller
down into the front cavity.
6.
8. Re-attach the sole plate using the 6 screws.
Over-current PowerRoller motor protection
An internal over-current protector has been
designed into your carpet washer to protect the
PowerRoller motor from over-current. When the
over-current protector activates, the PowerRoller
motor will stop operating. If this happens,
proceed as follows:
7a.
7b.
1. Turn the power switch off and unplug from
the electrical outlet.
2. Allow the carpet washer to sit for 15 seconds.
The over-current protector automatically
resets and cleaning may continue. If the
PowerRoller still does not work or the over-
current protector continues to activate, your
carpet washer may need servicing.
7c.
Note: The over-current protector protects the
PowerRoller motor only, not the main motor.
If the over-current protector activates, the
carpet washer will still operate; however, the
PowerRoller and spray will not work.
11
w w w . b i s s e l l . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING:
To reduce the risk of fire, electric
shock or injury, unplug from the
outlet before servicing.
Troubleshooting
Reduced Spray OR No Spray
Possible cause
Remedies
1. Clean water/formula tank may be empty
1. Turn power switch off; refill tank with
clean hand hot tap water and formula
2. Clean water/formula tank may not be seated properly 2. Turn power switch off; remove tank
and reseat
3. Pump may have lost prime
3. Turn power switch off; after 1 minute
turn on and depress spray trigger
Be sure there is cleaning formula in the
clean water/formula tank, it will make the
machine prime faster
4. Spray tip may be clogged
4. Remove spray tip and rinse thoroughly
under hot water. Replace with the o-ring tip
going down into the machine
No spray through the hose
Possible cause
1. Pump may not be primed
Remedies
1. Turn ReadyTools dial to FLOOR CLEANING
and depress spray trigger for a few a
seconds until you see suction coming up
the nozzle
Turn ReadyTools dial back to TOOLS
PowerRoller Does Not Turn
Possible cause
1. The brush belt is off or broken
Remedies
1. Refer to page 11, steps 1-5 for instructions
on how to access the belt
2. Look at the belt and check for breakage or
mis-alignment on the cogs. If there is no
evidence, replace all parts following steps 8-10.
3. In the event your belt is broken, a replacement
calling BISSELL consumer services. Refer
tothepartslist onpage14.Completeinstallation
instructions will come with the replacement belt
Machine not picking up solution
Possible cause
1. Dirty water tank may not be seated properly
Remedies
1. Turn power switch off; reseat tank
2. ReadyTools dial may be on TOOLS
3. Float may have shut off
2. Turn ReadyTools dial to FLOOR CLEANING
3. Turn power switch off and empty tank if
necessary. If tank is not full, wait
30 seconds and turn power switch on
4. Dirty water tank may be full
4. Turn power switch off and empty tank
Other maintenance or service not included in the manual should be performed by an
authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store
w w w . b i s s e l l . c o m
12
Download from Www.Somanuals.com. All Manuals Search And Download.
BISSELL Consumer Services
If your BISSELL product should require service:
In the UK, Australia or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you
the location of a BISSELL Authorized Service Center in your area. for all other countries, contact your local in
country distributor for questions, service, or repair.
If you have questions about your warranty or need replacement parts please contact the numbers below.
For UK inquiries:
For Australian inquiries:
monday - Thursday
friday
9 am — 5 pm
9 am — 4 pm
monday - friday 9 am — 5 pm
BISSELL AUSTRALIA PTY LIMITED
Unit 35
15 Ricketts Road
mount Waverley, Victoria 3149
Australia
BISSELL homecare (Overseas) Inc.
The Boat Yard
105 Straight Road
old Windsor
Berkshire, SL4 2SE
United Kingdom
Telephone: 1-800-811-183
Telephone: 0870-225-0109
For all other inquiries:
For New Zealand inquiries:
monday - friday 8 am — 4 pm
monday - friday 9 am — 5 pm
BISSELL homecare, Inc.
Po Box 1888
Parex Industries Ltd.
5 Tolich Place
Grand Rapids, mI 49501 USA
Telephone: 01-616-453-4451
fax: 01-616-453-1383
henderson 0610
Auckland
New Zealand
Telephone: 0800-247-735
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your model Number: ___________________
Please record your Purchase Date: ___________________
Note: Please keep your original sales receipt. It provides proof of date of purchase in the event of a
warranty claim. See Warranty on page 16 for details.
Please do not return this product to the store.
13
w w w . b i s s e l l . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement parts
Item Part No. Part Name
1
2
3
4
5
6
7
8
203-7204 Dirty Water Tank Assembly
203-7206 Dirty Water Tank Cap w/ Tether
203-7207 Clean Water/formula Tank Assembly
203-7211 Spray Tip
203-7210 Spray Tip Cover
203-7223 PowerRoller Assembly
203-7226 Replacement Brush Belt (with instructions)
203-7241 oxy Gen2 PowerTool Cap
1
5
2
6
3
7
4
8
Formulas
Item Part No. Part Name
1
2
3
4
5
6
7
710 Series BISSELL fiber Cleansing formula™ with Scotchgard™ Protector
720 Series BISSELL multi-Allergen Removal™ formula with Scotchgard™ Protector
730 Series BISSELL Pet odor and Soil Removal™ formula with Scotchgard™ Protector
740 Series BISSELL Natural orange Extract formula with Scotchgard™ Protector
750 Series BISSELL Lavender Essence formula with Scotchgard™ Protector
810 Series BISSELL oxy Gen2™
400 Series BISSELL Tough Stain Pre-cleaner™
1
2
3
4
5
6
7
w w w . b i s s e l l . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Additional accessories
These items are available for purchase as accessories for your BISSELL ReadyDry:
Item
1
Part No.
203-7240
Part Name
oxy Gen2™ PowerTool
2
3
4
5
6
7
8
203-7238
203-6653
203-6654
203-6652
203-7240
203-7239
210-3040
3" Tough Stain Tool
4" Upholstery Tool
6" Stair Tool
Powered TurboBrush™ hand Tool
Spraying 2-in-1 Crevice Tool
Spraying Crevice Tool
mesh Tool Storage Bag (Bag only)
1
5
2
3
4
8
6
7
Cleaning Formula: Refer to bottom of page 4 of this guide for a full selection of cleaning
formulas available for purchase.
15
w w w . b i s s e l l . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty - BISSELL ReadyDry
This warranty gives you specific legal rights, and you may also have other rights which may vary from country
to country. If you need additional instruction regarding this warranty or have questions regarding what it may
cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or
contact your local in country distributor.
Limited Two Year Warranty
Subject to the *EXCEPTIoNS AND EXCLUSIoNS identified below, BISSELL homecare, Inc., will replace (with
new or remanufactured components), at BISSELL’s option, free of charge from the date of purchase by the
original purchaser, for two years any defective or malfunctioning part do to manufacturers defect.
This warranty applies to product used for personal, and not commercial or rental service. This warranty does
not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction
caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered.
For UK inquiries:
For Australian inquiries:
monday - Thursday
friday
9 am — 5 pm
9 am — 4 pm
monday - friday 9 am — 5 pm
BISSELL AUSTRALIA PTY LIMITED
Unit 35
15 Ricketts Road
mount Waverley, Victoria 3149
Australia
BISSELL homecare (Overseas) Inc.
The Boat Yard
105 Straight Road
old Windsor
Berkshire, SL4 2SE
United Kingdom
Telephone: 1-800-811-183
Telephone: 0870-225-0109
For all other inquiries:
For New Zealand inquiries:
monday - friday 8 am — 4 pm
monday - friday 9 am — 5 pm
BISSELL homecare, Inc.
Po Box 1888
Parex Industries Ltd.
5 Tolich Place
Grand Rapids, mI 49501 USA
Telephone: 01-616-453-4451
fax: 01-616-453-1383
henderson 0610
Auckland
New Zealand
Telephone: 0800-247-735
BISSELL hOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY NATURE ASSOCIATED WITh ThE USE OF ThIS PRODUCT.
BISSELL’S LIABILITY WILL NOT EXCEED ThE PURChASE PRICE OF ThE PRODUCT.
*EXCEPTIONS AND EXCLUSIONS FROM ThE TERMS OF ThE LIMITED WARRANTY
ThIS WARRANTY IS EXCLUSIvE AND IN LIEU OF ANY OThER WARRANTIES
EIThER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WhICh MAY ARISE
BY OPERATION OF LAW, INCLUDING ThE IMPLIED WARRANTIES OF
MERChANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
©2009 BISSELL homecare, Inc
TO ThE TWO YEAR DURATION FROM ThE DATE OF PURChASE AS
DESCRIBED ABOvE.
Grand Rapids, michigan
All rights reserved. Printed in USA
Part Number 120-4095
Rev 1/09
Scotchgard is a trademark of 3m
w w w . b i s s e l l . c o m
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|