QuickSteamer®
U S E R ’ S G U I D E
1960 SERIES QUICKSTEAMER
2070 SERIES QUICKSTEAMER POWERBRUSH
3
Safety Instructions
Product View
4
5
Assembly/Accessories
6-8
Operations
Routine Maintenance
9
Troubleshooting
10
10
Consumer Services
11
Replacement Parts
12
Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
■
Do not unplug by pulling on cord.
Use only manufacturer’s recommended
attachments.
When using an electrical appliance,
basic precautions should be observed,
including the following:
■
Read all instructions before using your
■
Use only cleaning products formulated by
BISSELL for use in this appliance.
Keep openings free of dust, lint, hair, etc.
Keep appliance on a level surface.
Turn off all controls before unplugging.
Unplug by grasping the plug, not the cord.
Be extra careful when cleaning stairs.
Close attention is necessary when used by
or near children.
QUICKSTEAMER®.
To reduce the risk of fire, electric shock
or injury:
■
■
■
■
■
■
WARNING:
■
Do not expose to rain, store indoors.
Do not leave QUICKSTEAMER® when it is
■
plugged in.
Do not service QUICKSTEAMER® when it is
■
WARNING The Power Cord of this unit
contains chemicals, including lead, known in
the state of California to cause birth defects
or other reproductive harm.
plugged in.
■
Do not use with damaged cord or plug.
Do not use QUICKSTEAMER® if it has been
■
dropped, damaged, left outdoors or
dropped into water, have it repaired at an
Authorized Service Center.
Wash hand after handling
SAVE THESE INSTRUCTIONS.
■
Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around
sharp corners or edges, run appliance over
cord, or expose cord to heated surfaces.
GROUNDING INSTRUCTIONS.
This appliance must be connected to a grounded
wiring system. If it should malfunction or break
down, grounding provides a safe path of least
resistance for electrical current, reducing the risk
of electrical shock. The cord for this appliance
has an equipment-grounding conductor and a
grounding plug. It must only be plugged into an
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
■
Do not carry the appliance while in use.
Do not handle QUICKSTEAMER® plug or
■
appliance with wet hands.
Do not put any object into appliance openings,
use with blocked opening, or restrict air flow.
Do not expose hair, loose clothing, fingers
or body parts to openings or moving parts.
Do not pick up hot or burning objects.
Do not pick up flammable or combustible
■
■
■
Grounded
Outlets
■
materials (lighter fluid, gasoline, kerosene,
etc.) or use in the presence of explosive
liquids or vapor.
Grounding Pin
■
Do not use appliance in an enclosed space
filled with vapors given off by oil base
paint, paint thinner, some moth proofing
substances, flammable dust, or other
explosive or toxic vapors.
Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, gasoline, etc.).
WARNING: Improper connection
of the equipment-grounding conductor
can result in a risk of electrical shock. Check
with a qualified electrician or service person
if you aren’t sure if the outlet is properly
grounded. DO NOT MODIFY THE PLUG. If it
■
■
Do not modify the 3-prong grounded plug. will not fit the outlet, have a proper outlet
■
■
installed by a qualified electrician. This
appliance is designed for use on a nominal
120-volt circuit, and has a grounding attach-
ment plug that looks like the plug in the
drawing above. Make certain that the appli-
ance is connected to an outlet having the
same configuration as the plug. No plug
adapter should be used with this appliance.
Do not allow to be used as a toy.
Do not use for any purpose other than
described in this User’s Guide.
Use only on surfaces moistened by
cleaning process.
Connect to a properly grounded outlet only
See Grounding Instructions.
Unplug from outlet when not in use and before
conducting maintenance or trouble shooting.
■
■
■
This model is for household use only.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Spray
Trigger
Strain
Power Cord
Reliever
Handle™
Quick Release
Cord Wrap
2.
1.
Clean
Water
Tank
Lower
Cord
Wrap
Upper
Body
Power
Switch
Detent
Lever
Vent Cover
Containing
Foam Filter
Large,
Easy
Rolling
Wheels
Dirty
Water
Tank
Lower
Body
Floor
Nozzle
Spray Bar
Dirty Water
Tank Latch
4
Download from Www.Somanuals.com. All Manuals Search And Download.
How To Use This Guide
This User’s Guide has been designed to help you get the utmost
satisfaction from your BISSELL QuickSteamer Lightweight Deep
Cleaner. You’ll find assembly and operating instructions, safety pre-
cautions, as well as maintenance and troubleshooting instructions.
Please read this Guide thoroughly before assembling your cleaner.
Pay particular attention to the product diagram, assembly instructions,
and part names. Locate and organize all parts before assembly.
Familiarize yourself with the parts and where they go. Following
this User’s Guide will greatly enhance your ability to get the most
performance from your BISSELL QuickSteamer for many years.
Your QuickSteamer assembles quickly and easily. The only tool
you will need to assemble your deep cleaner is a Phillips Head
1.
2.
3.
4.
5.
(
screwdriver.
Your QuickSteamer is packaged with the following items:
Strain Reliever Handle
Upper Body
Lower Body with Dirty Water Tank
Clean Water Tank
2 Long/Partially Threaded Screws
1 Short/Fully Threaded Screw
How To Put It Together
Slide Upper Body into Lower Body.
1.
Secure with 2 Long/Partially Threaded Screws.
2.
Slide Strain Reliever Handle down into Upper Body until it
will go no further.
3.
Secure with Short/Fully Threaded Screw.
4.
Place Clean Water Tank on back of unit.
5.
Other Components
Clean Water Tank - holds 1/2-gallon of hot water and cleaning solution.
Dirty Water Tank - holds 1/2-gallon of dirty water.
Power Cord - for storage, wrap Power Cord around Upper and
Lower Cord Wraps, and secure Plug to Cord with molded clip.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use your BISSELL QuickSteamer
How to begin
WARNING:
To reduce the risk of fire, use
only BISSELL Advanced
Cleaning Formulas for Deep
Cleaning Machines.
Plan activities to give carpet time to dry.
1.
2.
3.
Use of cleaning formulas
that contain lemon or
Remove easily moved furniture (chairs, lamps,
coffee/cocktail tables, etc.) from room if needed.
pine oil may damage this
appliance and void warranty.
Chemical spot cleaners or
solvent-based soil removers
should not be used. These
products may react with the
plastic materials used in
Vacuum carpet thoroughly.
Decide where to begin — and end — your job. Clean in 3’ X 4’
sections, starting in areas farthest from exit. Plan to leave a path
open to empty soiled water and refill cleaner.
4.
5.
6.
®
your QuickSteamer,
causing cracking or pitting.
Carpeting will dry in three to four hours, depending on
carpet style and air circulation in room. A floor fan
speeds drying.
Tip:
Always vacuum
thoroughly before
you deep clean.
If possible, move
larger furniture to
an area you will
not be cleaning.
Replace furniture on damp carpeting by placing waxed
paper under legs until floor dries completely.
Getting ready
Remove the Clean Water Tank by lifting it straight up,
then away from the Lower Body.
1.
2.
2.
Formula
Measuring
Cap
Using the Formula Measuring Cap, add two (2) capfuls of
BISSELL® Advanced Cleaning Formulas for Deep
Cleaning Machines to the Clean Water Tank. Add 1/2-
gallon of hot (NOT boiling) tap water. Fill only to fill line –
do not overfill.
Unscrew to Remove
Replace and turn Formula Measuring Cap clockwise
until secure.
3.
4.
5.
Place Clean Water Tank on Lower Body.
Rotate Quick Release Cord Wrap™ to release the Power
Cord and plug into an outlet.
6.
Power
Switch
Turn Power Switch [located on the side of the Lower
Body] to ( ) ON.
6.
7.
If cleaner starts when first plugged in, switch cleaner
OFF ( ) until ready for use.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Treating
Pre-treat stubborn stains and highly soiled carpet in hallways and
other high-traffic areas.
Tip:
Deep cleaning
spots, spills
and high traffic
areas on a
Spray soiled area with BISSELL® Tough Stain PreCleaner.™
1.
regular basis can
prolong
carpet life.
Use a stiff-bristled brush to work formula into carpet pile.
2.
Wait 3 -5 minutes before deep cleaning.
3.
Deep Cleaning
Turn Power Switch [located on the side of the Lower
Body] to ( ) ON.
1.
Tip:
It is recommended that
every time your Clean
Water Tank is emptied
of solution that you
empty the contents of
the Dirty Water Tank. If
the Dirty Water Tank
gets too full, you may
begin to see foam
With foot, press the Detent Lever on right side of Lower Body.
2.
Depress Spray Trigger to spray cleaning solution.
Do not overwet.
3.
To suction up water, repeat motion over same area without
depressing Trigger.
spitting out of the vent
cover. When this
4.
happens you will know
it is time to empty the
Dirty Water Tank.
Repeat Steps 3 and 4 until no more dirt can be removed.
5.
Continue to clean entire carpet, working in 3’ x 4’ sections.
6.
Vent
Cover
7.
Empty the Dirty Water Tank when dirty water reaches the
full line, or when the Clean Water Tank is empty. See
7.
page 9 for instructions.
If Floor Nozzle stops spraying, turn Power Switch to OFF
(
) and check water and cleaning solution levels. Refill
8.
if needed.
Dirty Water Tank
7
Download from Www.Somanuals.com. All Manuals Search And Download.
printer spreads 3/7/03 4:07 PM Page 9
Belt and Brush Removal - 2070 Series only
*QuickSteamer PowerBrush models only
4.
3.
Turn the machine off and unplug from wall outlet.
1.
Remove clean and dirty water tanks.
2.
Lie machine down to access the bottom of the machine.
3.
5A.
5.
Unscrew the brush cover.
4.
Remove the brush end cap and remove belt from brush.
5.
Brush can now be removed.
6.
6.
7.
Belt can be removed by sliding off the motor pulley.
7.
Clean or replace belt. Attach belt to motor pulley and
brush, insert brush into right side end cap.
8.
Reattach the left end cap.
9.
9.
8.
Slide brush with the end cap attached back into place.
Replace the brush cover and screw into place.
10.
11.
10.
11.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Routine Maintenance
WARNING:
To reduce the risk of
injury from moving parts
and/or electrical shock,
turn Power Switch OFF
and disconnect polarized
plug from electrical
When you’re done
Turn Power Switch to OFF ( ) position.
1.
outlet before performing
troubleshooting checks.
Unplug Power Cord from outlet.
2.
3.
Remove and empty Dirty Water Tank.
a. Press detent Pedal and tip Handle back, laying it
gently on floor.
a.
b. Release Dirty Water Tank latches [1 each side] by
pulling up from bottom of latch and then out.
c. Carefully lift Dirty Water Tank from Lower Body.
d. Carry Dirty Water Tank to a toilet or sink. To empty,
pour out contents using opening at back of Tank.
e. Fill Dirty Water Tank with clean water through the
Vent Cover and rinse thoroughly. Discard water.
f. Remove lint and hair from Red Gasket in base of unit.
(Do not remove gasket)
Replace Dirty Water Tank on Lower Body and secure
with latches.
4.
5.
6.
b.
Wrap Power Cord around Quick Release Cord Wrap™ on
side of QUICKSTEAMER®.
Wipe all surfaces with a soft cloth. Store cleaner upright
in a protected, dry area.
c.
NOTE: You may have cleaning solution remaining
in the Clean Water Tank. You may store your
QuickSteamer this way for the next cleaning
task, but never keep soiled solution in the D
Water Tank.
d.
e.
Vent
Cover
CAUTION:
Do not store unit where
freezing may occur.
Damage to internal
components may result.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble Shooting
Reduced spray or no spray.
Possible Causes
Remedies
Clean Water Tank empty
Refill Tank with water and formula
Deep Cleaner not picking up cleaning solution.
Possible Causes
Remedies
Dirty Water Tank not aligned/secured
Check Tank for proper alignment and secure
with side latches
Dirty Water Tank is full
Empty Tank
BISSELL Consumer Services
For information about repairs or replacement parts, or questions about
your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement parts - BISSELL QuickSteamer
Item Part No.
Part Name
QuickSteamer– 1960 Series
1
203-5601
Handle Assembly
2
3
4
203-5602
203-5603
203-5604
Cross Action Brush
Clean Water Tank
Dirty Water Tank
5
603-7822
Bare Floor Tool*
QuickSteamer PowerBrush– 2070 Series
1
3
4
603-2010
603-2009
603-2008
Handle Assembly
Clean Water Tank
Dirty Water Tank
6
7
8
9
603-2006
603-2007
0710
Dirt Lifter PowerBrush
Belt
Fiber Cleansing Formula™ 48 oz
Multi-Allergen Removal™ Formula 48 oz
Tough Stain PreCleaner™
0720
10 044
* Not all parts included with every model.
1
5
9
2
3
4
6
7
8
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
About Your Warranty
This warranty gives you specific legal rights, and you may also have other rights which
may vary from state to state. If you need additional instruction regarding this warranty
or have questions regarding what it may cover, please contact BISSELL Consumer
Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the
product BISSELL Homecare Inc. will repair or replace (with new or remanufactured
components or products), at BISSELL’s option, free of charge from the date of
purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental
service. This warranty does not apply routine maintenance components such as filters,
belts, or brushes. Damage or malfunction caused by negligence, abuse, or use not in
accordance with the User's Guide is not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in
your area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty, contact
BISSELL Consumer Services.
Website or E-mail:
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or write:
BISSELL Homecare Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE
ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE
PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL
OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE
OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may
©2003 BISSELL HOMECARE, Inc.
not apply to you.
Grand Rapids, Michigan
All rights reserved. Printed in USA.
Part Number 603-5600
Rev 3/03
Visit our website at:
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|