ProHeat™
U S E R ’ S G U I D E
7901 SERIES
8910 SERIES
3
Safety Instructions
4
Product View/Accessories
Assembly
5
6-17
Features / Operations
Routine Maintenance
17-19
Troubleshooting
20-21
22
Consumer Services
23
Replacement Parts
24
Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
ꢀ
When using an electrical appliance, basic
precautions should be observed, including
the following:
Use only cleaning products formulated by
BISSELL for use in this appliance.
Keep openings free of dust, lint, hair, etc.
Do not point attachment nozzle at people
or animals.
ꢀ
ꢀ
Read all instructions before using your
®
PROHEAT
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Keep appliance on a level surface.
Turn off all controls before unplugging.
Unplug before attaching the Turbo Brush.
Be extra careful when cleaning stairs.
Close attention is necessary when used by
or near children.
WARNING: The Power Cord on this product
contains lead, a chemical known to the State
of California to cause birth defects or other
reproductive harm. WASH HANDS AFTER
HANDLING.
WARNING:To reduce the risk of
Do not immerse.
Use only on surfaces moistened by
cleaning process.
Always connect to a properly grounded outlet.
See Grounding Instructions.
Unplug from outlet when not in use and before
conducting maintenance or troubleshooting.
Do not leave machine when it is plugged in.
Do not service machine when it is plugged in.
Do not use with damaged cord or plug.
If appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped in to water, have it repaired at an
authorized Service Center.
Use indoors only.
Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around
sharp corners or edges, run appliance over
cord, or expose cord to heated surfaces.
Do not carry the appliance while in use.
Do not unplug by pulling on cord. Unplug by
grasping the plug, not the cord.
Do not handle plug or appliance with wet hands.
Do not put any object into appliance openings,
use with blocked opening, or restrict air flow.
Do not expose hair, loose clothing, fingers
or body parts to openings or moving parts.
Do not pick up hot or burning objects.
fire, electric shock, or injury:
ꢀ
™
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
SAVE THESE INSTRUCTIONS.
ꢀ
ꢀ
THIS MODEL IS FOR HOUSEHOLD USE ONLY.
Commercial use of this unit voids the
manufacturer’s warranty.
GROUNDING INSTRUCTIONS
ꢀ
ꢀ
This appliance must be connected to a grounded
wiring system. If it should malfunction or break
down, grounding provides a safe path of least
resistance for electrical current, reducing the risk
of electrical shock. The cord for this appliance
has an equipment-grounding conductor and a
grounding plug. It must only be plugged into an
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
ꢀ
ꢀ
ꢀ
ꢀ
Grounded
Outlets
ꢀ
ꢀ
Grounding Pin
ꢀ
Do not pick up flammable or combustible materials
(lighter fluid, gasoline, kerosene, etc.) or use in the
WARNING: Improper connection
of the equipment-grounding conductor
can result in a risk of electrical shock.
Check with a qualified electrician or
service person if you aren’t sure if the
outlet is properly grounded. DO NOT
MODIFY THE PLUG. If it will not fit the
outlet, have a proper outlet installed by a
qualified electrician. This appliance is
designed for use on a nominal 120-volt
circuit, and has a grounding attachment
plug that looks like the plug in the
drawing above. Make certain that the
appliance is connected to an outlet having
the same configuration as the plug.
No plug adapter should be used with
this appliance.
presence of explosive liquids or vapor.
ꢀ
Do not use appliance in an enclosed space filled
with vapors given off by oil base paint, paint thinner,
some moth proofing sub stances, flammable dust,
or other explosive or toxic vapors.
ꢀ
Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, gasoline, etc.).
Do not modify the 3-prong grounded plug.
Do not allow to be used as a toy.
Do not use for any purpose other than
described in this User’s Guide.
Do not operate the appliance unless the belt door
is securely assembled in the location provided.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Use only manufacturer’s recommended
attachments.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Keep plenty of genuine BISSELL Fiber Cleansing
Formula™ and Scotchgard™ Protector Cartridges
on hand so you can clean and protect whenever
it fits your schedule. Always use genuine
BISSELL deep cleaning formulas. Non-BISSELL
cleaning solutions may harm the machine and
void the warranty.
Trigger
Upper
Handle
Tool Caddy
Crevice Tool
Storage
Power Cord
Quick Release
SmartTemp®
Switch
3.
Power
Switch
Tough Stain
Brush Storage
2.
4.
Hex
Nuts
Tank-in-
Tank™
TurboBrush®
Storage
(select models
only)
5.
Handle
Release
Applicator Tool Storage
1.
Flex Hose
Lower Handle
SmartTemp®
Ready Light
Accessories
*All items may not be included with your model.
More tools are available. To order replacement parts
or tools please refer to page 23.
SmartMix®
Switch
Flow Indicator
(Filter Inside)
ReadyTools™
Dial
SmartMix®
Tank
4” Upholstery Tool
Tough Stain Brush PreTreat Wand
(Available on select
(Available on select
models only.)
models only.)
Spraying Crevice Tool
(Available on select models only.)
Bare Floor Attachment
(Available on select models only.)
DirtLifter®
PowerBrush
Belt Access Door
Floor Nozzle Window
®
N
IO
T
C
U
S
™
Floor Cleansing Formula
H
S
UGH ST
ECLEAN
U
R
FOR DEEP
B
CLEANING MACHINES
P
e
n
e
t
r
a
t
e
s
a
n
d
L
o
o
s
e
n
s
T
o
u
g
h
S
ta
i
n
s
Safely Deep Cleans and
Revitalizes No-Wax Floors
&
Em
b
e
d
i
n
g
d
e
d
D
i
r
t
b
e
f
o
r
e
D
e
e
p
Cl
ea
n
D
32 FL.OZ.
(946 mL)
M
A
Y
B
E
I
R
R
I
T
A
T
I
N
G
T
O
THE
EYES.
CAUTION:
R
E
A
D
B
A
C
K
P
A
N
E
L
CAREFULLY
Scotchgard™
protector
16 oz. BISSELL
Fiber Cleansing
Formula™ with
Scotchgard™
Protection
16 oz.
16 oz. BISSELL
Multi-Allergen
Formula™ with
Scotchgard™
Protection
16 oz.
Floor
Applicator
Tool
Tough Stain
TurboBrush®
(Available on select
models only.)
PreCleaner™
Cleansing
Formula™
4
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use this guide
WARNING:
Do Not plug in your cleaner
until you have completely
assembled it per the following
instructions and are familiar
with all instructions and
operating procedures.
This User’s Guide has been designed to help you get the utmost
satisfaction from your BISSELL ProHeat. You’ll find assembly and
operating instructions, safety precautions, as well as maintenance
and troubleshooting instructions. Please read this Guide thoroughly
before assembling your deep cleaner.
Pay particular attention to the product diagram, assembly
instructions, and part names. Locate and organize all parts before
assembly. Familiarize yourself with the parts and where they
go. Following this User’s Guide will greatly enhance your ability
to get the most performance from your BISSELL ProHeat for
many years.
Your ProHeat comes in 3,
easy to assemble components.
The only tool you will need to assemble your cleaner is a Phillips
head
screwdriver.
Upper Handle
Lower Handle
Tool Caddy
2
4
How To Put It Together
Refer to Assembly Diagram on page 4
Slide upper handle onto lower handle.
1.
Feed bundled power cord through Tool Caddy from caddy’s
2.
3.
4.
flat side.
5
Align upper handle holes and Tool Caddy holes.
Place hex nut into back of Tool Caddy and hold in place. Insert
bolt from front to back turning into the hex nut until snug. Do
not over tighten. Repeat for the second bolt and hex nut.
6
Insert 2 screws into lower 2 holes.
Turn until snug.
ON
OFF
5.
6.
7.
Snap tools into Storage on the Tool Caddy as shown in
figure 6.
Wrap Power Cord and Flex Hose as shown in figure 7.
ProHeat assembly is now complete.
7
ON
OFF
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Features of your BISSELL ProHeat
The BISSELL SmartClean® System
The ProHeat is a home cleaning system that automatically mixes hot
tap water with Fiber Cleansing Formula and heats the
solution as it is applied to the carpet. The combination of heated
cleaning solution, powered brush and suction provide a safe and
effective method of cleaning.
SmartTemp®
Temperature control automatically heats the cleaning solution
as it is being applied to the carpet (*) to safely optimize
cleaning effectiveness.
SmartTemp Ready Light
The Power Switch controls power to the machine; both
switches must be ON for SmartTemp to work.
1.
The SmartTemp Switch is found on the back of the handle
next to the Power Switch. You may choose not to use the
2.
Power Switch
SmartTemp
Switch
SmartTemp feature if you are cleaning delicate wool or
oriental rugs.
*SmartTemp heats the cleaning solution for carpet
and bare floor application only. It does not heat
solution sprayed through the accessory tools.
ON
OFF
ON
OFF
The SmartTemp Ready Light indicates when the heater is
ON. The heater should be turned on two minutes before
3.
cleaning, to become fully warmed up and ready for
cleaning. It is found on the front of the handle where it is
easy to see while you clean.
SmartTemp increases the water temperature approximately
25° and will not allow it to exceed 180.°
SmartMix
bottle
4.
SmartMix®
Provides custom control for each cleaning job.
Lift the SmartMix concentrate bottle up and out of the
machine base.
1.
Turn the bottle over so that the valve cap is in an upward
position. Unscrew the valve cap and fill the bottle to the
mark with BISSELL Fiber Cleansing Formula.
2.
3.
Replace the valve cap turning until snug.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SmartMix
Replace SmartMix concentrate bottle.
4.
5.
Choose the SmartMix setting that fits the cleaning job.
Water Rinse / Carpet Protector -This setting
must also be used when applying the carpet
protectant through the applicator, to prevent the
pump from temporarily losing its prime.
SmartMix
Dial
Normal- automatically provides the best mix of
water and concentrate for most cleaning jobs.
High Traffic- automatically mixes the right amount
of water and concentrate to dissolve tough grime
and heavy soil. Note: Residual cleaning materials left
in carpet from other products may cause excessive
foaming when picked up. If foam is overflowing
tank, move SmartMix dial to “Water Only” position
until the condition stops.
Tip:
Deep Cleaning
stairs and high
traffic areas on a
regular basis and
using the carpet
protectant can
prolong carpet
life.
Note: Both the SmartMix Bottle and the clean
water tank must have liquid in them in
order for the machine to spray. If one tank
is empty, the machine will temporarily
lose its prime and not apply either
cleaning solution or water only.
DirtLifter® PowerBrush
WARNING:
To reduce the risk of fire,
use only BISSELL Deep
Cleaning Formula for full
size machines in your
ProHeat. Use of cleaning
formulas which contain
lemon or pine oil may
damage this appliance
and void warranty.
The powered brush roll at the floor nozzle is designed to
enhance cleaning performance. The bristle pattern lifts out the
deep down dirt while gently grooming carpet fibers. The floating
suspension self-adjusts to all carpet heights and protects
your carpet if you leave the power switch ON. When the
machine handle is in the fully upright position, Carpet Saver™
automatically raises the brush off the carpet.
Chemical spot cleaners or
solvent based soil
Tank-in-Tank™
removers should not be
used. These products may
react with the plastic
materials used in your
ProHeat, causing cracking
or pitting.
Our Tank-in-Tank system is designed with a bladder inside for
clean water. As you clean, the bladder will empty. Dirty water
collects in the tank outside the bladder.
Step on handle release to lay the machine handle
down out of the way.
1.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Tank-in-Tank Continued
Lift the Tank-in-Tank handle. The handle locks the
lid in place.
2.
3.
Carry it like a bucket to fill at the sink.
Lift and Carry
Note: You may notice hair and debris deposits on
the carpet that were loosened by the
3
brushing action (especially with newer
carpets that have never been deep cleaned
before). This debris should be picked up
and thrown away. Debris that deposits in
the Brush Belt should be cleaned between
uses to keep the Belts running free.
Set the tank down and rotate the handle forward to
unlatch the lid. Lift off and set the lid aside.
4.
5.
Rotate Handle to
Unlatch
Find the mouth of the Bladder and fill to the bottom of
the neck with clean hot tap water. *Do not boil or
microwave water as it can destroy the Bladder.
4
5
Note: Fill the Bladder with clean hot tap water only.
Replace the tank lid matching the lid and tank edges.
Handle must be in the forward position to reinstall.
6.
7.
8.
9.
Rotate the handle to the carrying position to re-latch
the lid.
Fill bladder only with
clean hot tap water
Replace tank in machine base, seating firmly in place.
Rotate handle back down to the latched position.
Note: Both the SmartMix Bottle and the clean
water tank must have liquid in them in
order for the machine to spray. If one tank
is empty the machine will not apply either
cleaning solution or water only.
9
Latched
When It’s Time to Empty Tank-in-Tank
Remove the Tank-in-Tank – follow steps 1 and 2
on page 7 and 8.
1.
2.
Carry the Tank-in-Tank, like a bucket, to the sink where
you will dispose of the dirty water.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
When It’s Time to Empty Tank-in-Tank Continued
Remove Tank Lid by rotating handle forward to unlatch
lid and lifting lid off tank.
3.
4.
5.
Pour out dirty water.
Pour out
dirty water
3
Rotate Handle to
Unlatch
4
After each use, remove and rinse the lint screen located
on the tank lid.
A. Remove tank assembly from unit.
B. Remove tank lid.
C. Remove any debris caught in lint screen.
D. Reinsert lint screen on tank lid. The screen will
5D
Lint Screen
5C
click into place
E. Replace tank lid.
F. Reinsert tank assembly into unit.
3
Refill with clean tap water as above, steps 5 through 9
on page 8, and refill the SmartMix bottle with BISSELL
Fiber Cleansing Formula as necessary.
6.
7.
Fill bladder
only with clean
hot tap water
8
When the cleaning job is complete, rinse out the
Tank-in-Tank by rinsing clean water between the bladder
and tank.
6
Latched
Return Tank-in-Tank to the machine, following steps 6
through 9 on page 8.
8.
9.
Refer to the Maintenance section, pg. 17 for the
final cleanup.
Tip:
A special red
float device
in the tank will
cause the cleaner
to stop removing
solution from the
carpet and the
motor sound will
rise in pitch to let
you know the
dirty water tank is
full.
The Flow Indicator
Tip:
The Flow Indicator is located on the machine base. It spins when
the trigger is pressed to indicate that the machine is applying
cleaning solution to the floor. It will stop spinning to indicate that the
SmartMix bottle or bladder needs to be refilled, or when the trigger
is released. Flow Indicator does not spin when set to Tool setting.
Thorough
vacuuming
before deep
cleaning will
prevent early
clogging of
lint trap.
ReadyTools Dial
This provides above floor cleaning with the flip of a switch.
Just choose the cleaning tool or protector applicator, attach
to the flex hose and ProHeat is ready to clean
Flow Indicator
upholstery, stairs or apply extra protection against dirt and
tough stains when using the Scotchgard protector applicator.*
*Set the dial to Floor Cleaning when cleaning
carpets or bare floors or set it to Tools/PreTreat
when using the flex hose attachments or for
pre-treating floors, or when applying the
Scotchgard protector applicator.
OLS
TO
PRETREA
T
FLOOR
CLEANING
*SmartTemp heats the cleaning solution for carpet
and bare floor application only. It does not heat
solution sprayed through the accessory tools.
ReadyTools Dial
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Before You Clean Carpets
Plan activities to give carpet time to dry.
1.
2.
3.
4.
Remove easily moved furniture from the room (chairs,
lamps, coffee tables, etc).
9
EXIT
12
10
3'
7
Vacuum thoroughly to pick up loose debris and pet hair
before using the ProHeat.
1
T
AR
HERE
6
ST
5
2
4'
Plan your cleaning route to leave an exit path. It is best
to begin cleaning in the corner farthest from your exit.
Machine Preparation
Set up the machine following instructions in
The Features section, pages 6-9.
1.
2.
Use Fiber Cleansing Formula in the SmartMix tank when
cleaning carpets, stairs or upholstery. Use clean water in
the SmartMix tank for gentle cleaning, rinsing, or when
applying carpet protectant.
Choose the SmartMix setting to match the
cleaning job.
3.
4.
Set the ReadyTools switch to either Tools/PreTreat or
Floor Cleaning.
PreTreating
Pretreating is recommended to improve cleaning
effectiveness for heavily soiled carpet, high traffic
areas such as entryways and hallways, or stairs.
Tip:
Set the SmartMix dial to High Traffic.
Try pre-treating
stairs or entry
ways with
1.
Set ReadyTools dial to PreTreat.
BISSELL Tough
2.
3.
Stain PreCleaner™.
Then deep
Plug into a proper outlet and turn ON both the Power
and SmartTemp switches.
clean with the
SmartMix®
UGH ST
ECLEAN
dial set on
P
e
n
et
r
a
t
e
n
s
T
o
u
g
h
S
t
a
i
n
s
s
a
n
d
Loose
&
Em
be
n
g
d
d
e
d
D
i
r
t
C
l
e
a
n
i
While pressing the trigger, slowly make several passes
over the area to be cleaned. Caution: Do not overwet.
b
efor
e
D
e
e
p
High Traffic.
4.
5.
Turn the machine Power switches OFF and let BISSELL
Deep Cleaning Formula dissolve the tough soil for 1-2
minutes before continuing.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Carpet Cleaning
Plug into a proper outlet and turn the Power and the
SmartTemp switches ON. Wait two minutes for the
heater to warm up before beginning to clean.
1.
2.
ATTENTION
While pressing the trigger, make one slow forward wet
pass and another one back. Let the SmartTemp heated
formula and DirtLifter Powerbrush do the work for you.
Caution: Do not overwet.
BERBER CARPET
OWNERS:
Some Berber Carpets have a
tendency to fuzz with wear.
Repeated strokes in the
same area with an ordinary
vacuum or deep cleaner may
aggravate this condition.
Please see Stain Removal
instructions on page 12.
Note: Take care not to run over loose objects or
edges of area rugs. Stalling brush may
result in premature belt failure.
Release the trigger and make one slow forward and back
pass over the same area to remove any residual dirty water.
3.
4.
5.
Repeat cleaning passes until solution being pulled up
appears clean.
Continue passes without pressing the trigger until you
can’t see any more water being pulled up.
Note: Both the SmartMix and the clean water
tank must have liquid in them in order for
the machine to spray. If one tank is empty
the machine will not apply either cleaning
solution or water only.
When the cleaning job is complete refer to the
Maintenance section for machine cleanup and storage
instructions on page 17-19.
6.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Stain Removal
Do Not Delay! Failure to attend to an accident soon after it occurs
may cause it to set and become permanent.
Before treating any stain, follow these pre-treatment steps:
Blot up liquids with an absorbent cloth or paper towels.
White materials are recommended because certain dyes
1.
may bleed and make the stain worse.
Gently scrape up semi-solids with a spoon or spatula. Do
not use a knife or other utensil with sharp edges
2.
because it could damage the carpet or upholstery.
If the area has dried, remove the remaining semi-solids
and residue with a sweeper or vacuum.
3.
Be sure to pre-test any spot removal solutions or chemicals
on an inconspicuous area first. This is extremely
4.
important; different dyes and materials could be damaged
or discolored by a cleaning solution. If such a change
should occur, try a different solution or call a professional. If
cleaning on Berber Carpet gently run your machine over
a hidden area. If no fuzzing occurs, continue cleaning in
soiled area.
Use one of the following methods to Preclean the stain:
Using BISSELL Tough Stain Precleaner™, generously
spray the area with the formula. Gently work the solution
5.
with a clean cloth or towel into the area using light
strokes from the edges of the stain to the center. When
your cloth reaches the center of the stain, gently pinch it
in an upward motion. Make sure to turn and change your
cloth frequently and do not rub the stain. You may repeat
this process several times.
or
Use your BISSELL deep cleaner as a Precleaner. With
one of the tools attached to hose, set the Ready Tools
dial to Pretreat and the SmartMix dial to the High Traffic
setting. Spray the area with solution and allow the Deep
Cleaning formula to penetrate for 3-5 minutes.
Once the Precleaning is complete, use the attached tool
to gently scrub the stain with back and forth strokes.
6.
Allow to dry. Some difficult stains may require a second
treatment.
7.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TurboBrush®
(Available on select models only)
Assembly
Unplug cleaner from the outlet before attaching TurboBrush. Attach
TurboBrush to the flex hose by pressing tool onto the grip/trigger
until button snaps into hole. Make certain tool is securely in place.
Use
Move the TurboBrush switch to the “BRUSH” position.
This activates the brush when the unit is running.
1.
Place the tool directly on the soiled surface. Apply
downward pressure on the tool and pull towards you
2.
while pulling trigger to spray cleaning solution.
SUCTION
BRUSH
Release the spray trigger and move the switch to the
“SUCTION” position. Vacuum the area until no more
3.
cleaning solution can be removed.
Repeat steps 1-3 until no more dirt can be removed.
Caution: Do not overwet.
4.
When You’re Done
Disconnect the TurboBrush from the flex hose by pushing
down on the button lock and pulling straight off.
1.
Once removed from the flex hose, the TurboBrush can be
cleaned.
2.
A) Move the switch to the “SUCTION” position
B) Rinse under running water.
C) Check spray nozzle for dirt. If necessary, clean with
a soft bristle brush.
D) Replace TurboBrush in its special storage
location on the handle front. (on select models only
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Scotchgard™ protector Applicator (Optional)
The Scotchgard protector applicator (with formula included) can be used to
help retain the carpet cleanliness you achieve with your ProHeat machine.
For best results the post cleaning treatment should be applied while the
carpet is still wet or damp. It is recommended that the Scotchgard protector
is applied every 12 months in all carpeted areas, and after every deep
cleaning for high traffic areas such as entryways and stairs.
Immediately after cleaning and rinsing your carpets, empty the
Tank-in-Tank and refill the bladder with clean hot tap water.
(See page 7 & 8 for instructions.)
1.
Set the ReadyTools dial to Tools/Pretreat.
2.
Purge the hose to eliminate cleaning solution from the tube by
spraying water through the hose without attachments into a
3.
sink for 15-30 seconds.
Attach cartridge to the applicator tool, following instructions
on cartridge.
4.
Turn the SmartMix dial to the Water Rinse/Carpet Protectant Setting.
5.
Place the Scotchgard protector applicator onto the end of the Flex
Hose. The water from the Tank-in-Tank will automatically mix with
6.
the concentrated protectant formula contained in the cartridge.
Before applying Scotchgard protector, test a small, hidden area
Tip:
If clogged, soak
applicator tool in
hot tap water
for colorfastness. Examine area when dry. If color is affected,
7.
do not use. For upholstery look for manufacturer’s cleanability
code tag. Use on fabrics coded “W” or “WS”. If coded “S” or
“X” do not use. Not recommended for use on velvet, silk vinyl,
leather or 100% cotton upholstery.
before using.
Plan your route to leave an exit path. It is best to begin
protecting in the corner farthest from your exit.
8.
Apply Scotchgard protector in a slow sweeping motion with a
slight overlap of the treated area. For best coverage, follow the
9.
guide on the cartridge.
One 8 oz. cartridge protects 200 square feet (18.6 square
meters). This is equal to two average size rooms (each at 10 x
10 feet or 3 x 3 meters. Periodically check the product level in
the bottle to ensure best coverage.
10.
Be careful not to spray the protector onto furniture or fabric
that has not been tested for colorfastness. If this does occur,
11.
wipe off the protector.
Remove bottle from spraying tool. If concentrate is left, put the
cap on and store for later use at room temperature.
12.
With applicator tool still on the end of flex hose, spray clean
hot water into sink to avoid any future clogging.
13.
Store tool on the back of unit in the caddy.
14.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Clean Upholstery and Small Areas
Important - Check Upholstery Tags:
Check manufacturer’s tag before cleaning. “W” or “WS” on the
tag means you can use your ProHeat. If the tag is coded with
“X” or “S” (with a diagonal strike through), or says “Dry Clean
Only,” do not proceed. The Scotchgard™ protectort is not rec-
ommended for use on velvet, silk, 100% cotton upholstery,
vinyl or leather. If manufacturer’s tag is missing or not coded,
check with your furniture dealer.
1.
Check for colorfastness in an inconspicuous place.
2.
3.
Manufacturer’s tag
If possible, check upholstery stuffing. Colored stuffing
may bleed through fabric when wet.
Plan activities to give upholstery time to dry.
WARNING:
To reduce the risk of
injury, be extra careful
when cleaning stairs.
Make sure machine is
secure and level.
4.
5.
Vacuum thoroughly to pick up loose debris and pet hair.
Use a vacuum with a brush attachment and a crevice
tool to clean in fabric folds and tufts.
Machine Preparation
Tip:
Set up the machine following instructions in The
Features section, pages 6-9.
1.
2.
3.
Use the BISSELL
Pet Odor and Soil
Removal™
Use Fiber Cleansing Formula in SmartMix tank.
Formula to deep
clean pet odor
and soil.
Set the ReadyTools dial to Tools or PreTreat.
* SmartTemp heats the cleaning solution for carpet
and bare floor application only. It does not heat
solution sprayed through the accessory tools.
Set SmartMix Dial to Normal.
Tip:
4.
Deep cleaning
carpeting and
upholstery with
BISSELL Multi-
Allergen Removal™
Formula regularly
can reduce dust
mite waste and
allergens in your
home.
Cleaning Technique
Choose the 4” Small Area Tool, the Tough Stain Brush, or
the Spraying Crevice Tool and connect to the flex hose.
1.
Plug into a proper outlet and turn Power Switch ON.
2.
3.
While pressing the trigger, slowly move the spraying tool back
and forth over the soiled surface. Release the trigger to suction
soiled water.
Continue to clean soiled area, working in small sections,
until no more dirt can be removed.
4.
5.
Caution: Do not overwet.
When the cleaning job is complete refer to the
Maintenance section for machine cleanup and storage
instructions on page 17-20.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning Bare Floors
Tilt
Handle
Back
The Bare Floor Tool (available with select models only)
provides effective cleaning for linoleum, vinyl, and tile floors.
Caution: Do not use on hardwood floors.
Use BISSELL Floor Cleansing Formula.
1.
2.
3.
4.
5.
Handle Release
Vacuum or sweep thoroughly to pick up loose debris and pet hair.
Remove easily moved furniture from the room, (chairs, tables, etc.)
Plan your cleaning route to leave an exit path.
Carrying
Plan activities to allow 30 minutes for the floor to dry completely.
Attach the Bare Floor Tool
Step on the handle release to lay the machine handle down.
1.
2.
3.
4.
Remove the Tank-in-Tank from the machine base.
Lift the machine base to expose the underside of the nozzle.
Bottom Front Edge of
Machine Base
Attach Bare Floor Tool to nozzle with long tab to the right side
(ReadyTools side) of the nozzle.
Bare Floor
Cleaning Tool
Snap Together
First attach left side (short Tab) catching tab over nozzle edge.
5.
6.
Gently bend long tab (right side) outward to easily snap over
edge of clear nozzle on left.
Machine Preparation
Set up machine following instructions in the Features
section, pages 6-9. Be sure to thoroughly rinse out any
remaining Fiber Cleansing Formula from the SmartMix bottle to
prevent slippery linoleum, vinyl, and tile floors. Use BISSELL
Floor Cleansing Formula in the SmartMix tank.
1.
Check ReadyTools dial - it should be set on Floor Cleaning.
Choose the SmartMix setting to match the cleaning job.
2.
3.
4.
Plug into a proper outlet and turn Power Switch ON. Turn
SmartTemp switch ON. The SmartTemp Ready Light illuminates
and the ProHeat is ready to clean.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Bare Floor Cleaning Technique
Slowly move the machine nozzle with Bare Floor Tool
forward and back over soiled surface one time while
pressing the trigger. Caution: Do not over wet.
1.
2.
WARNING:
To reduce the risk of fire,
electric shock or injury
unplug from outlet
Repeat the motion without pressing the trigger using the Bare
Floor Tool to squeegee and suction up the dirty water.
before servicing.
Repeat steps 1 and 2 backing along the exit path.
Allow about 30 minutes for the floor to dry completely.
3.
4.
5.
Tip:
SmartMixBottle
may be stored
with concentrate
ready for your
next cleaning job.
Make sure dial is
turned to the
When the cleaning job is complete refer to the
Maintenance/Storage section on page 17-20.
To remove Bare Floor Tool gently bend long tab (right side)
outward and pull tool down away from nozzle. Rinse
thoroughly, dry and store
6.
Water Rinse/
Carpet Protector
Setting when
storing.
Routine Maintenance
Turn Power and SmartTemp switches OFF.
1.
2.
Unplug power cord from the outlet and coil around Power Cord
Quick Release.
Remove and rinse tools in clean, running water, dry and
replace tool caddy.
3.
Coil flex hose around storage brackets on tool caddy.
4.
5.
Remove Tank-In-Tank, dispose of dirty water. See Features
section, Page 7-9.
ON
OFF
Rinse out Tank-In-Tank and replace on the machine; Clean out
lint trap.
6.
7.
Clean out the Flow Indicator Filter each time it is used to ensure
best cleaning performance. Unscrew the Flow Indicator Cap, lift
out the red rotor and white filter. Rinse all three parts in tap water.
Replace the filter and rotor. Replace the Flow Indicator Cap; turn
until snug, do not over-tighten.
Wipe all exterior surface with a soft cloth.
Cap
8.
9.
Store cleaner upright in a protected, dry area.
Rotor
Filter
Note: ProHeat uses water and must not be stored
where there is a danger of freezing. Freezing will dam-
age internal components and void the warranty.
When carpet is dry, vacuum again to remove hair and fuzz
that the ProHeat may have loosened.
10.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Pump Belt Replacement
2
Turn the machine off and unplug from the wall outlet.
1.
2.
3.
4.
3b
Step on the release pedal and recline the handle down onto
floor. (see illustration).
3a
Remove Tank-In-Tank and SmartMix tanks. Set them aside
(see illustration).
4
Remove Belt Access Door located near the Floor Cleaning/
Tools switch by inserting a flat head screwdriver into the slot
nearest to the handle and gently prying the access door off
(see illustration).
5
Turn the machine onto its side so the belt access area is
facing upward (see illustration).
5.
6.
On the bottom of the machine, near the belt access area,
is a red retainer plate that holds the black brush arm and
brush in place. Using a Phillips head screwdriver remove the
screw that holds the red retainer plate in place. Set red
retainer plate and Phillips head screw aside (see illustration).
6
Remove the black brush arm that holds the brush in place. Set
the black brush arm aside (see illustration).
7.
8.
9.
7
Remove the “toothed” brush belt from the brush then from the
red pump pulley. Set the “toothed” brush belt and brush aside.
Locate and remove broken pump belt.
8
9
18
Download from Www.Somanuals.com. All Manuals Search And Download.
To Install the Replacement Pump Belt
1
With the unit still on its side, loop one end of the replacement
pump belt around the red pump pulley and then the other end
around the silver motor shaft (see illustration). Do not twist the
replacement pump belt.
1.
Re-install the toothed brush belt first onto the red pump pulley
and then onto the toothed end of the brush (see illustration).
2.
3.
4.
Re-Install the brush into the base of unit.
2
4
Place the black brush arm onto the brush and slide black
brush arm into base of unit. The black brush arm and brush
should slide easily into original position(see illustration).
Re-install the red retainer plate and Phillips head screw
(see illustration).
5
6
5.
6.
Using your finger, gently spin the replacement pump belt on
the silver motor shaft. If assembled correctly, the replacement
pump belt should rotate freely around the silver motor shaft
and drive pulley without obstruction. The brush should also
rotate freely when the silver motor shaft is turned.
7a
7b
Turn the machine right side up and replace the Tank-In-
Tank, SmartMix tank and belt access door (see illustration).)
7.
8.
Assembly is now complete.
If you have any questions, or are having trouble installing your
replacement pump belt, please call BISSELL Consumer
Services at 1-800-237-7691.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
SmartTemp Ready Light does not illuminate.
Possible Causes
Remedies
WARNING:
The SmartTemp switch is not
Turn on the SmartTemp switch.
To reduce the risk of
fire, electric shock or
injury unplug from outlet
before servicing.
turned ON.
The machine Power Switch is not
turned ON.
Both switches must be ON to
activate the SmartTemp Ready Light.
Reduced spray or no spray
Possible Causes
Remedies
Refill bladder with hot tap water.
Bladder may be empty.
SmartMix bottle may be empty.
Fill with BISSELL Advanced Cleaning
Formula for cleaning or water if
rinsing,or using the Scotchgard
protector applicator.
The filter may be clogged.
Clean out Flow Indicator Filter, page 17.
Tanks may not be seated properly. Turn power OFF; remove & reseat
tanks. Inspect for presence of seals.
Pump may have lost prime.
Turn power OFF; after 1 minute turn
ON and depress trigger.
The Pump Belt may be broken.
Turn the machine OFF and unplug
from the outlet. To check if a Pump
Belt has broken, you will need a flat
head screwdriver. Insert the blade end
into the lower slot of the Belt Access
door to release the lower snap. If
necessary, insert the blade end into
the upper slot to release the upper
snap. Examine the belt for breakage.
You should be able to see the Pump
Belt looped around the motor shaft. If
it is broken or missing, please refer to
Replacement Parts on pg.23 before
calling Consumer Services. Complete
installation instructions will
Lift Here
accompany the replacement belt.
Insert
Screwdriver
Blade Here
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Continued
DirtLifter PowerBrush does not turn.
Possible Causes
Remedies
The Brush Belt or Pump Belt
is off or broken.
Turn the machine OFF and unplug from
the outlet. To check if a Pump Belt has
broken, you will need a flat head
screwdriver. Insert the blade end into
the lower slot of the Belt Access door
to release the lower snap. If necessary,
insert the blade end into the upper slot
to release the upper snap. Examine the
belt for breakage. If broken refer to
pages 18-19.
Carpet Protector is not spraying.
Possible Causes
Remedies
Follow instructions on cartridge
assuring proper fit.
Bottle not connected
properly to the tool.
Solution clogging the
Spray trigger.
Soak applicator tool only in hot water.
Spray without the cartridge attached to
purge any residual Solution left in
the tool.
Applicator tool spray is blocked.
Soak applicator tool only in hot water.
Spray without the cartridge attached to
purge any residual Solution left in
the tool.
SmartMix not set on water/rinse
carpet protector setting.
Set to proper setting.
ReadyTool dial not set on tool setting. Set to tool setting.
Cleaner not picking up solution.
Possible Causes
Remedies
Set ReadyTools dial to either Tools or
PreTreat or Floor Cleaning.
Ready Tools dial may be at the
wrong setting for the cleaning job.
Nozzle Window may not be
properly attached.
Press down firmly on the black oval
gasket at the top window to make sure
the two tabs on the back of the Nozzle
Window are snapped into the mating
slots in the main housing.
Tank-in-Tank lid is not
properly installed.
Re-install lid; refer to The Operations
section.
Tank-in-Tank is not properly seated. Tank-In-Tank must be firmly seated to
function; remove and reseat Tank-in-Tank.
Poor tool position.
(Hand held attachments only).
Adjust angle; apply more downward
pressure.
Tank-in-Tank has picked up
maximum dirty water.
Empty Tank-in-Tank, refer to
the Operations section.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BISSELL Consumer Services
For information about repairs or replacement parts, or questions about
your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of date of
purchase in the event of a warranty claim. See "About Your Warranty"
on page 24 for details.
Please do not return this product to the store.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement parts - BISSELL ProHeat®
Item Part No.
Part Name
1* 210-9201
2* 210-9148
3* 210-1197
4* 214-9131
5* 214-9142
6* 215-9155
4” Small Area Tool
Spraying Crevice Tool
TurboBrush®
Bare Floor Tool
PreTreat Wand
Tough Stain Brush
7
8
215-9043
015-4439
015-9041
210-1785
210-1795
555-6503
210-4052
014-9865
215-0628
015-0621
015-3500
0464
Tank Assembly Complete (Includes Lid Assembly)
Tank Lid Assembly
Tank Bottom (Assembly)
SmartMix® Bottle (Includes Cap Assembly)
SmartMix® Cap Assembly
Flow Indicator Assembly
Window Gasket
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Floor Nozzle Window and Gasket
Replacement Pump Belt (With Instructions)
Replacement Brush Belt (With Instructions)
Lint Screen
Scotchgard™ protector Cartridge
Applicator Tool
215-2152
0710
0720
0730
Fiber Cleansing Formula™ 48oz
Multi-Allergen Removal™ Formula 48oz
Pet Odor and Soil Removal™ Formula 48oz
*Not all parts are included with every model.
1
6
2
3
8
4
9
5
SUCTION
BRUSH
10
7
11
17
13
15
16
12
14
19
18
20
21
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
About Your Warranty
This warranty gives you specific legal rights, and you may also have other rights which
may vary from state to state. If you need additional instruction regarding this warranty
or have questions regarding what it may cover, please contact BISSELL Consumer
Services by E-mail, telephone, or regular mail as described below.
Full One Year Warranty
Upon receipt of the product, BISSELL Homecare, Inc will repair (with new or
remanufactured components), or if repair is not possible after a reasonable number of
attempts, either replace (with new or remanufactured product) your ProHeat, or refund
the purchase price, whichever you prefer, free of charge for one year from the date of pur-
chase -any defective or malfunctioning part. See information below on “How to Return Your
BISSELL Product for Service”.
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to routine maintenance components such as filters, belts, or brushes.
Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any
other use not in accordance with the User's Guide is not covered.
If your BISSELL product should require service:
Call BISSELL Consumer Services at the number below or visit the BISSELL website -
www.bissell.com to locate a BISSELL Authorized Service Center in your area.
Contact BISSELL Consumer Services.
Website or E-mail:
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. .ET
Or write
BISSELL Homecare Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE
ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE
PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
©2002 BISSELL HOMECARE, Inc.
Grand Rapids, Michigan
All rights reserved. Printed in USA.
Part Number 010-5814
Rev 11/02
Visit our website at:
Scotchgard is a trademark of 3M
24
Download from Www.Somanuals.com. All Manuals Search And Download.
|