Bionaire Humidifier BCM4505 User Manual

COOLMOISTURE  
humidifier  
MODEL BCM4505  
BCM4509  
BCM4510  
Read instructions before operating. Retain for future reference.  
Instruction Leaflet  
INFO-LINE  
If after having read this leaflet, you have any questions  
or comments on your humidifier,  
call 1-800-253-2764 in North America.  
Model BCM4510 Shown  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HUMIDIFIER SAFETY  
PLEASE READ AND SAVE  
THESE IMPORTANT SAFETY  
INSTRUCTIONS.  
IMPORTANT SAFEGUARDS  
When using electrical appliances, basic safety precautions  
should always be followed to reduce the risk of fire, electric  
shock, and injury to persons, including the following:  
1. Read all instructions before using the appliance.  
2. To avoid fire or shock hazard, plug the appliance directly  
into a 120V AC electrical outlet.  
3. Keep the cord out of heavy traffic areas. To avoid fire hazard,  
NEVER put the cord under rugs, near heat registers, radiator,  
stoves, or heaters.  
4. DO NOT place humidifier near heat sources such as stoves,  
radiators, and heaters. Do locate your humidifier on an inside  
wall near an electrical outlet. The humidifier should be at least  
4" away from the wall for best results.  
5. NEVER place humidifier in an area where it is accessible to children.  
6. NEVER use humidifier in a closed room, particularly where a child  
may be sleeping, resting, or playing (a closed room may result in  
excessive humidity).  
7. WARNING: Do not attempt to refill humidifier without first  
unplugging the unit from its electrical outlet. Failure to heed  
this warning may cause personal injury.  
8. NEVER place anything over moisture outlet when unit is running.  
9. NEVER drop or insert any object into any openings.  
10. DO NOT operate any appliance with a damaged cord or plug,  
if the appliance malfunctions, or if it has been dropped or damaged  
in any manner. Return appliance to manufacturer for examination,  
electrical or mechanical adjustment, or repair.  
11. Use appliance only for intended household use as described in this  
manual. Any other use not recommended by the manufacturer may  
cause fire, electric shock, or injury to persons. The use of attach  
®
ments not recommended or sold by Bionaire may cause hazards.  
12. DO NOT use outdoors.  
13. Always place humidifier on a firm, flat, level surface (4” from wall).  
A waterproof mat or pad is recommended for under the humidifier.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
The length of cord used on this appliance was selected to reduce  
the hazards of becoming tangled in, or tripping over a longer cord.  
If a longer cord is necessary an approved extension cord may be used.  
The electrical rating of the extension cord must be equal to or greater  
than the rating of the humidifier. Care must be taken to arrange the  
extension cord so that it will not drape over the countertop or tabletop  
where it can be pulled on by children or accidentally tripped over.  
HOW YOUR COOL MOISTURE HUMIDIFIER WORKS  
®
Your Bionaire Cool Moisture humidifier draws dry air through the rear  
air intake grill area. This air is then passed through a moisture–laden  
wick filter which retains the minerals and deposits. The resulting moist  
air is directed back into the room from the top air grill.  
Tip: This humidification system provides a cool, invisible moisture  
output. It is normal not to see the mist.  
PRE-OPERATING INSTRUCTIONS  
1. Be sure the humidifier is switched off and disconnected from  
the electrical outlet.  
Reservoir  
Handle  
2. Select a location for your  
humidifier, on a flat surface,  
about 4" away from the wall.  
Do not place your humidifier  
on furniture, a floor location  
that will not be damaged by  
moisture is best.  
Water  
Reservoir  
Reservoir  
Cap  
Moisture  
Outlet  
Housing  
Support Handle  
power  
refill  
mode  
humidistat  
Humidifier  
Housing  
Control  
Panel  
Float  
(underneath)  
3. Remove the water reservoir,  
by holding the reservoir handle  
and lifting straight upwards.  
Wick  
Filter  
Base  
Figure 1  
4. Remove the humidifier housing by holding the housing support  
handle and lifting straight upwards. Check to see that the wick  
filter is properly in place. Replace the humidifier housing.  
FILLING THE WATER RESERVOIR  
5. Twist off the water reservoir cap located on the bottom of the  
water reservoir by turning counter clockwise and fill the water  
reservoir with cool, fresh water. Do not fill with warm water as  
this may cause leaking.  
6. After filling the water reservoir, replace the water reservoir cap by  
firmly turning clockwise and then replace the water reservoir on  
the base. The water reservoir will immediately begin to empty into  
the base.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING INSTRUCTIONS  
1. Plug the power cord into a 120V AC electrical outlet.  
2. Turn the mode knob to the High setting.  
3. Turn the humidistat knob to the highest setting.  
USING THE HUMIDISTAT  
The humidistat feature allows you to set and maintain the humidity level  
you wish for your room. The humidistat is designed to operate between  
30% and 65% relative humidity range. The recommended setting  
is 40-45%.  
For BCM4505: To maintain  
Humidistat  
Knob  
Power Light  
Figure 2  
this setting, position the  
humidistat (figure 2) knob  
in the middle position.  
power  
refill  
mode  
humidistat  
Turn the knob clockwise as far  
as it will turn to achieve the  
highest humidistat setting. In  
this setting, the humidifier will  
run constantly.  
Mode Knob  
Control  
Panel  
Refill Light  
To lower your desired humidity level, simply turn the knob counter  
clockwise to choose your setting.  
For BCM4509: To take advantage of the SmartTouch™ Electronic  
Humidistat, press the MODE button until the speed is set in either  
the HIGH or LOW setting, and the Desired Humidity is set. When  
the humidity level rises above the set humidity, the humidifier will stop.  
When the humidity level drops below the set humidity, the humidifier  
will turn on automatically.  
NOTE: When the SmartTouch™ Electronic Humidistat is set, either  
the HIGH or LOW power light and the percent humidity light will remain  
lit during operation. The SmartTouch™ Humidifier has memory. This  
means that when you turn the unit back on, it will be at the last setting  
the humidifier was set at.  
For BCM4510: The auto setting is designed to operate between  
30% and 65% relative humidity range. (The recommended setting  
is 40-45%.) The auto setting may be used with any of the three  
auto speed settings (High, Medium or Low).  
To program a specific humidity level in the auto setting, follow these  
instructions.  
1. Use the mode button to scroll to either Auto/High, Auto/Medium,  
or Auto/Low.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Set the humidifier to the desired room humidity level by pressing the  
(+) or (–) buttons, in increments of 5%. If you scroll past the maximum  
setting of 65%, the display will automatically loop back to 30%.  
3. Now the desired room humidity level is set.  
NOTE: When the humidity in the room is less than the level you have  
programmed, the humidifier will continue to produce moisture. Once the  
room humidity level has been achieved, the humidifier will turn off. When  
the room humidity drops below your set level, the unit will automatically  
begin producing moisture again.  
Depending on the size of your room and your personal comfort,  
you will set your humidistat at different levels. If condensation forms  
on your windows or walls, or your measured room humidity is above  
50%, then turn off your humidifier, or lower your humidistat level.  
(Humidity can be measured by the use of a hygrometer, such as  
®
Bionaire BT254 or BT400 Digital humidity and temperature monitor.  
NOTE: Allow up to 30 minutes for the filter to fully absorb water  
and for the unit to produce moisture.  
If you do not plan to use the humidifier for two or more days, make  
sure any residual water is drained from the water tank, base and wick  
filter to prevent algae or bacteria growth.  
NIGHTLIGHT INSTRUCTIONS (For BCM4510 Only)  
the BCM4510 is equipped with a nightlight which illuminates the control  
panel screen in a dark room setting. This nightlight operates on a sensor,  
and will illuminate when the room becomes dark. When the room  
becomes light, the nightlight feature will automatically turn off. To inacti-  
vate the nightlight, simply press the nightlight button on the control  
panel. To re-activate the nightlight feature, simply press the light button  
again (to see if light is on, place finger over sensor).  
REFILLING THE WATER RESERVOIR  
When the water reservoir runs out of water, the refill light will illuminate  
on the control panel. The fan will continue to run to help dry out the  
humidifier. Unplug the power cord from the electrical outlet, and follow  
steps under "Filling the Water Reservoir."  
If you do not plan to use the humidifier for two or more days, make  
sure any residual water is drained from the water reservoir, base  
and wick filter to prevent algae or bacteria growth.  
REPLACING THE WICK FILTER  
Through normal use, waterborne minerals and sediment become  
trapped in the wick filter. The harder your water, the greater the amount  
of minerals in the water, and the more often you will need to change your  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
wick filter. Filter Monitor (after replacing the wick section) you will be  
able to check the life of the filter on your humidifier by checking the  
Filter Monitor located on the moisture outlet. When the unit is not in  
operation, the Filter Monitor (BCM4505/4509) will also read as OFF.  
When the unit is turned on, the Filter Monitor needle will need 60  
minutes to read the current filter condition. If the needle reads change  
after 60 minutes, then filter replacement is needed. Regular filter  
replacement is necessary to ensure optimal humidifier performance.  
To replace the wick filter, follow the steps below.  
1. Turn the mode knob off and unplug the humidifier from  
the electrical outlet.  
2. Remove the water reservoir and humidifier housing to access  
the base tray.  
3. Discard the old wick filter and insert a new wick filter into  
the filter brackets found in the base.  
4. Replace the humidifier housing and then the water reservoir.  
5. Repeat “Operating Instructions” steps listed within.  
It will take about 30 minutes for the humidifier to reach maximum  
output.  
You can obtain your filter model by calling 1-800-253-2764 in North  
America or by visiting your nearest retailer or authorized service center.  
This humidifier takes model WF2630 replacement filter.  
CLEANING AND MAINTENANCE INSTRUCTIONS  
Humidifiers provide comfort by adding moisture to dry, heated  
indoor air. To get the most benefit from the humidifier and avoid  
product misuse, follow all instructions carefully, specifically the  
operation, care and maintenance guidelines. Please note that  
this is an electrical appliance, and requires attention when in use.  
In addition, if you do not follow the recommended care and  
maintenance instructions, micro-organisms may be able to  
grow in the water within the humidifiers reservoir.  
Daily Maintenance  
1. Before cleaning, set the mode to the OFF position and unplug  
the unit from the electrical outlet.  
2. Lift off the water reservoir and the humidifier housing.  
3. Carry the base and the water reservoir to the sink, remove the wick  
filter, then drain and rinse the base and water reservoir thoroughly to  
remove any sediment and dirt. Wipe clean and dry with a clean cloth  
or paper towel.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Put the wick filter back in the base, replace the humidifier housing,  
then refill the water reservoir with cool tap water as instructed under  
“Filling the Water Reservoir.”  
5. If moisture forms on the walls or windows, turn off the humidifier.  
Weekly Maintenance  
Remove scale:  
1. Repeat steps 1-3 above.  
2. Clean the base by partially filling the base with one 8-oz cup  
®
®
of undiluted white vinegar, or use Clean-Away by Bionaire . Let  
solution stand 20 minutes, cleaning all interior surfaces with a soft  
brush. Dampen a cloth with undiluted white vinegar and wipe out  
entire base to remove scale.  
3. Rinse with clean warm water to remove scale and the white  
vinegar solution before beginning to disinfect the reservoir.  
4. Remove the float from the bottom of the humidifier housing  
®
and remove any scale by soaking in vinegar or Clean-Away  
solution. Rinse thoroughly and re-install the float into the unit.  
DISINFECT RESERVOIR:  
1. Fill water reservoir with 1 teaspoon of chlorine bleach  
and 1 gallon of water.  
2. Let the solution stand for 20 minutes, swishing every few minutes.  
Wet all surfaces.  
3. Empty the reservoir after 20 minutes, and rinse well with water until  
the bleach smell is gone. Dry with a clean cloth or paper towel.  
4. Check to see if it is time to change the wick filter.  
5. Refill the water reservoir with cool water, replace the humidifier  
housing and the water reservoir. Repeat Operating Instructions.  
STORAGE INSTRUCTIONS  
If your humidifier will not be in use for two days or more,  
or at the end of the season follow these instructions.  
1. Clean and dry the humidifier thoroughly as per the “Weekly  
Maintenance” instructions.  
2. Let the humidifier dry completely before storing. Do not store  
with water inside the base or water reservoir.  
3. Remove the reservoir cap. Do not store with the reservoir  
cap in place.  
4. Throw away the wick filter. Do not leave a wick filter inside  
the humidifier.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Store in a cool dry location.  
6. Order your new filter so it will be ready for next season.  
SERVICE INSTRUCTIONS  
1. Do NOT attempt to repair or adjust any electrical or mechanical  
functions on this unit. Doing so will void the warranty. The inside  
of the unit contains no user serviceable parts. All servicing should  
be performed by qualified personnel only.  
2. If you need to exchange the unit, please return it in its original  
carton, with a sales receipt, to the store where you purchased  
it. If you are returning the unit more than 30 days after the date  
of purchase, please see the enclosed warranty.  
3. Should your humidifier require service, please call 1-800-253-2764  
in North America for further assistance.  
4.  
If you have any other questions or comments, feel free to write  
Canada  
6385 Shawson Drive  
Mississauga, Ontario  
Canada, L5T 1S7  
PO Box 400  
Milford, MA 01757  
USA  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting for your Cool Mist Humidifier  
Probable Cause  
Unit not plugged in.  
Power failure.  
Trouble  
• Power light not illuminated.  
Solution  
Plug in unit.  
Check circuit breaker or  
outlet.  
Water reservoir empty.  
Scale build-up in  
base.  
• “Empty/Refill” light  
illuminated.  
Refill Water reservoir.  
Remove base and flush  
out residue.  
Clean float tubes and  
float.  
Scale build up on float  
Filter has not  
• Mist output minimal to  
none.  
Wait 15 minutes before  
starting humidifier.  
absorbed water.  
Mineral buildup in base.  
Regular cleaning of tray  
after each use will help  
keep the unit functioning  
properly.  
Humidistat is set too low.  
Set the humidistat to  
high.  
Wick Filter needs  
to be replaced.  
Replace your wick filter  
(WF2630) by calling  
1-800-253-2764, or visit  
Mist is invisible.  
Normal operation.  
Check to see if inlet or  
outlet grills are blocked  
Rubber O-ring is missing  
• Water leaks from water  
reservoir.  
Remove reservoir  
cap then replace  
or reposition ring.  
Tighten the  
or improperly placed.  
Reservoir Cap not  
tight enough.  
reservoir cap.  
Your filter needs  
to be changed.  
• Water Filter turns brown.  
Replace your wick filter  
(WF2630) by calling  
1-800-253-2764, or visit  
In areas with particular  
hard water your wick  
filter will need to be  
changed frequently.  
Use Clean Away Solution  
(DMS216), to order call  
1-800-253-2764, or visit  
Mineral deposits cause  
• Film on water reservoir.  
• Water cloudy.  
Replace your wick filter  
(WF2630) by calling  
film on tank to build up.  
1-800-253-2764, or visit  
Filter needs  
Refill using cool water.  
to be replaced.  
Using warm water  
to refill reservoir.  
Set the humidistat to a  
higher or lower setting.  
Humidifier is reacting  
• Humidistat cycles on/off.  
• Very tight reservoir cap.  
to room humidity level.  
Over tightened.  
Add liquid soap or  
pertroeum jelly to cap  
gasket to ease opening.  
9
10  

BenQ Digital Camera DC T800 User Manual
BenQ Projector mw814st User Manual
Black Box Cable Box RMT3200A R2 User Manual
Black Box Outboard Motor Black Box User Manual
Bloomfield Coffeemaker 9220 User Manual
Briggs Stratton Pressure Washer 20255 User Manual
Brother All in One Printer DCP4020C User Manual
Campbell Hausfeld Air Compressor IN203203AV 11 00 User Manual
Canon Wireless Office Headset WFT E6 User Manual
Christie Digital Systems Projector DS+ Series User Manual