1
2
OPTIONAL ACCESSORIES
INTAKE
HOSE COUPLER KIT 8" (203mm) TR
P/N 810525 Quick release coupler joins 2
hoses together to increase vacuuming
distance and allows hoses to be separated
for storage.
HOSE CONNECTOR KIT 8" (203mm) TR
P/N 810524
For permanently connecting 2 hoses
together to increase vacuuming distance .
ALL MODELS
EXHAUST
EXHAUST EXTENSION KIT P/N 810637
Increases exhaust height 11"(280mm) for
loading debris into elevated locations.
EXHAUST HOSE KIT P/N 811206
[6"(152mm) x 10' (3.0m)] Quick release
coupler and hose increases exhaust distance.
EXHAUST HOSE COUPLER KIT P/N 811207
[6"(152mm)] Quick release coupler joins 2
hoses together to increase exhaust distance
and allows hoses to be separated for
storage.
EXHAUST HOSE CONNECTOR KIT
P/N 800336 [6"(152mm)] Permanently joins
2 exhaust hoses together to increase
exhaust distance.
PANEL FILTER KIT P/N 810584 Provides air
filter panel for use on truck and trailer
mounted debris enclosures.
PORTABLE DEBRIS BAG P/N 810660
3
3
T h a n k Yo u f o r S e l e c t i n g
1.3 yds. (1.0m ) or 28.4 bushels (1000L).
For portable use. Several bags can be filled
and left for later pickup.
The Powerful TRUCK LOADER VACUUM
Operator Owner's Manual
HTR1803VEU, TR1304HEU, TR1104EU
Specifications
3
TR1304HEU
TR1104EU
HTR1803VEU
ENGINE: H.P.
ENGINE: WEIGHT
ENGINE: TYPE
18 H.P. TWIN OHV VANGUARD GUARD 13.0 HP (10.68 kW)
11.0 HP (9.04 kW)
52.0 lbs. (23.6 kg)
B & S 4 cycle Intek I/C
4.0 qt. (3.8 L)
79 lbs. (35.83 kg)
68.4 lbs. (31 kg)
HONDA 4 cycle
6.9 qt. (6.0 L)
Briggs & Stratton 4 Cycle IC Twin
ENGINE: FUEL CAPACITY 9 qt.(8.52 L),Float feed carb.& fuel pump
ENGINE: OIL CAPACITY
1.75 qt. (1.66 L), Oil pump w/filter
1.16 qt. (1.1 L)
0.875 qt. (0.8 L)
UNIT TOTAL WEIGHT
TOTAL SHIPING WEIGHT: 291 lb (132.0 kg)
263 lb (119.3 kg)
229 lb (108.9 kg)
255 lb (115.7 kg)
224 lb (101.6 kg)
250 lb (113.4 kg)
UNIT SIZE:
OVERALL LENGTH: HTR 36.5"(0.93m) / TR 35"(0.89M) OVERALL WIDTH: 24.25" (0.62m)
OVERALL HEIGHT: 66" (1.68m)
Page 1 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 811237
Form No. F050304A
9
GENERAL SAFETY
For your safety and the safety of others, these directions should be followed:
Do not operate this machine without first reading
owner's manual and engine manufacturer's manual.
·DO NOT operate without discharging exhaust into enclosed
container.
·DO NOT operate during excessive vibration.
·DO NOT remove hose until engine has been turned off and has
come to a complete stop.
Use of Ear Protection is recommended while
operating this machine.
Use of Eye and Breathing protection is recom-
mended when using this machine, especially in dry
and dusty conditions.
·DO NOT operate machine with hose or exhaust elbow removed.
·DO NOT use this machine for vacuuming exclusively sand,
dust, fine dirt, rock, glass, string like material, grain, rags,
cans, metal, bark or water.
·DO NOT place hands or feet inside nozzle intake opening,
near debris outlet or near any moving parts.
·DO NOT operate this machine on slopes greater than 20%.
·DO NOT pick up any hot or burning debris, or any toxic or
explosive material.
·DO NOT start engine without hose and exhaust elbow
connected firmly in place to housing and exhaust outlet.
·DO NOT allow children to operate this equipment.
10
ASSEMBLY
5. ASSEMBLE nozzle handle loop (item 82), to nozzle handle using
screw (item 80), washer (item 6) and lock nut (item 5). Adjust handle
loop to desired height and angle and securely tighten in place.
6. ASSEMBLE nozzle handle (item 78), to nozzle (item 77), using
screws (item 80), washers (item 79), washers (item 4) and lock nuts
(item 5).
Read all safety and operating instructions
before assembling or starting this unit.
PUT OIL IN ENGINE BEFORE STARTING.
Your Billy Goat is shipped from the factory in one carton and is
completely assembled except for the exhaust elbow, nozzle, handle
loop for nozzle, hose booms, hose bands, hose coupler, hose clamps
and related hardware.
7. ATTACH assembled nozzle to hose using hose clamp (item 60).
Before tightening hose clamp, position nozzle handle upward when hose
is stretched to prevent twisting load on hose assembly during operation.
8. ASSEMBLE tube square boom (item 51), to boom pivot (item 50),
using chain loop assembly (item 54), washers (item 4) and lock nut
(item 52).
1. ASSEMBLE exhaust elbow (item 10), to main unit and firmly tighten
knobs (item 90), that are preassembled to main unit.
9. ASSEMBLE remaining chain loop assembly (item 54), to end of tube
square boom (item 51) using washer (item 4) and lock nut (item 52).
10. SLIDE boom assembly into square tube on front of housing.
11. ASSEMBLE hose bands (item 56) around hose and onto chain loop
assemblies on boom assembly using screws (item 55) and lock nuts
(item 52) (see ADJUSTING HOSE BOOM on page 5).
2. SECURELY ATTACH unit to tailgate of a truck or to a trailer, so that
the exhaust discharges into an enclosed container.
3. ATTACH hose to hose coupler (item 24), using hose clamp (item
60) NOTE: This unit is equipped with a unidirectional hose. Assemble
hose so that interior hose material seams face toward unit.
4. ASSEMBLE hose coupler to housing of main unit and securely
tighten knob (item 13), that is preassembled to housing front plate.
11
PACKING CHECKLIST
Boxing Checklist
TR MODELS
These items should be included in
your carton. If any of these parts are
missing, contact your dealer.
Briggs & Stratton 11 HP
Check
Engine
Manual Per
Model
Exhaust Elbow 811191
10
Honda 13 HP
HTR MODELS
Boom Square Arm 810875
Boom Pivot WA 810870
51
50
Briggs & Stratton
Vanguard-Twin 18 HP
Band Hose Boom 8" (203mm)
810880 Qty. 2
56
Hose 8"x 12.5'
P/N 810523
Coupler Weld Assy. 8"(203mm)
811170
59
60
Handle Loop Nozzle
P/N 811019
Hose Clamps 8"(203mm)
810566 Qty. 2
Parts Bag &
Literature Assy
P/N 811128
Handle Nozzle 811020
78
77
Parts Bag
& Literature
Assy
Nozzle 8"(203mm) 811007
Page 3 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 811237
Form No. F050304A
13
12
CONTROLS
PARTS BAG & LITERATURE ASSY P/N 811201
Throttle Controls
Start
position
Washer 5/16
Fender
8172020 Qty. 4
Literature Checklist
79
4
Honda
START
Units have
Check
Owner's
Manual
811202
frame
Owner's
Manual
mounted
throttle
controls as
shown
Washer 5/16 SAE
8172008 Qty. 4
Check
here.
Literature
Literature
Parts Bag
Parts Bag
811203
Chain Loop Assy
810878 Qty. 2
STOP
54
Nut Lock 1/4-20
8160001 Qty. 4
52
5
Stop
position
Check
Literature
Literature
HTR / TR
Accessories
HTR / TR
Accessories
811208
Briggs Vanguard Units
have an engine mounted
throttle control.
Nut Lock 5/16-18
8160002 Qty. 3
Engine
Stop
Switch
Check
Warranty
Card
400972
Washer 5/16 FLAT CUT
8171003 Qty. 1
Warranty
Card
6
Start
position
Screw Cap 5/16-18 x 1 1/2
8041030 Qty. 3
EU Declaration
of Conformity &
EU Distributor
List 811204
Check
80
55
EU Declaration
of Conformity
& EU
Distributor List
Screw Cap 1/4-20 x 1 3/4
8041009 Qty. 2
Stop
position
14
INSTRUCTION LABELS
15
ENGINE LABELS
These labels should be included on your Vacuum. If any of these
labels are damaged, replace them before putting this equipment into
operation. Item and part numbers are given to help in ordering
replacement labels..
Briggs & Stratton Vanguard
FUEL SHUTOFF
ON
STOP
RUN
RUN
CHOKE
OFF
DANGER
ENGINE MAINTENANCE
1. CHECK OIL LEVEL
8 HOURS
2. CHECK & CLEAN AIR CLEANER
3. CHANGE OIL
4. REPLACE OIL FILTER
5. CLEAN COOLING FINS
25 HOURS
50 HOURS
100 HOURS
100 HOURS
See Operating and Maintenance Instructions
Label Danger Keep Hands
and Feet Away
Item 3 Part No.400424
Label Danger Flying Material Label Read Owner's Manual
Item No. 19 Part No. 810736 Item 15 Part No.830301
Honda
OIL ALERT
WHEN OIL LEVEL LOW,
READ OWNER'S MANUAL
ENGINE STOPS IMMEDIATELY.
USE PROTECTION
BEFORE OPERATING, MAKE SURE:
Label Ear Eye Breathing
Item No. 48 Part No. 890254
EXHAUST ELBOW IS ATTACHED.
EXHAUST IS DISCHARGING INTO
ENCLOSED CONTAINER.
HOSE IS ATTACHED.
ALL GUARDS ARE ATTACHED.
OPERATING INSTRUCTION IS OBTAINED.
WARNING
EXPLOSIVE FUEL
STOP ENGINE AND ALLOW TO
COOL BEFORE REFUELING.
H
O
N
D A
M
O
T O
R
C
O
., L T D .
M
A
D
E
I N J A PA
N
STOP ENGINE AND ALLOW TO
COOL BEFORE REFUELING.
KEEP ENGINE CLEAN OF DEBRIS.
INSPECT MACHINE BEFORE EACH USE AND REPLACE ANY
WORN AND DAMAGED PARTS.
Briggs & Stratton
PROPERLY SECURE EQUIPMENT BEFORE TRANSPORTING.
NEVER SERVICE UNIT WITHOUT DISCONNECTING SPARK PLUG WIRE.
USE ONLY A QUALIFIED MECHANIC TO SERVICE THIS MACHINE.
ABRASIVE DEBRIS WILL SHORTEN UNIT LIFE.
Label Do Not Fill While Engine Is Hot
Item 81 Part No.400268
ON
Label Caution
Item 47 Part No.830138
OFF
RUN
CHOKE
Read and follow Operating
Instructions before running engine.
Clean debris from all engine surfaces
regularly to prevent engine overheating,
premature failure, or fire.
Gasoline is flammable. Allow engine
to cool at least 2 minutes before fueling.
THIS ENGINE EQUIPPED WITH
LOW OIL SENSOR, IF ENGINE WILL
NOT START, CHECK OIL LEVEL
Label Warning Engine Overheat
Item 49 Part No.811215
Engines emit carbon monoxide,
DO NOT run in enclosed area.
Part No. 811237
Form No. F050304A
Page 4 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
16
OPERATION
INTENDED USE: This machine is designed for vacuuming
leaves, grass clippings and other types of organic litter.
Debris mixed with cans, bottles and small amounts of sand can
be vacuumed; however, it is not this machine's primary
purpose. Vacuuming cans, bottles and sand will affect the
longevity of your machine.
16.6
HOSE OPERATION TIPS
THE HOSE IS A REPLACEABLE WEAR ITEM.
FOR BEST HOSE OPERATION RESULTS, FOLLOW THESE
RECOMMENDATIONS.
Do not operate if excessive vibration occurs. If excessive
vibration occurs, shut engine off immediately and check for
damaged or worn impeller, loose impeller bolt, loose impeller
key, loose engine or lodged foreign objects. Note: See parts list
for proper impeller bolt torque specifications. (See trouble
shooting section on page 12).
Keep hose as straight as possible during operation for best
pick-up and to avoid clogs.
Avoid sharp bends in hose which will reduce efficiency and may
promote clogs.
NEVER DRAG HOSE. Always remove and store hose before
transporting unit.
Like all mechanical tools, reasonable care must
be used when operating machine.
Inspect machine work area and machine before operating.
Make sure that all operators of this equipment are trained
in general machine use and safety.
PUT OIL IN ENGINE BEFORE STARTING.
16.1
STARTING
SECURE LOADER TO TAILGATE OR MOUNTING:
ENGINE: See engine manufacturer’s instructions
for type and amount of oil and gasoline used. Engine must be
level when checking and filling oil and gasoline.
ENGINE SPEED: Controlled by throttle lever on the frame
(18HP Twin on engine). Under normal conditions, operate at
minimum throttle to accomplish your current cleaning task.
FUEL VALVE: Move fuel valve to "ON" position (when provided
on engine).
fig. 1
INTAKE HOSE: Must be attached to front plate to start engine.
CHOKE: Located on engine near engine throttle panel.
STOP SWITCH: Move to on position (when provided).
ADJUSTING HOSE BOOM:
Properly adjusting the boom will prevent most hose clogs from
occurring and will give optimum vacuum performance by
keeping hose straight next to housing (see fig. 2).
THROTTLE: Move remote throttle control to fast position. Pull
starting rope to start engine.
IF YOUR UNIT FAILS TO START:
See Troubleshooting on page 12.
Boom Assembly
after hose has
been stretched.
16.2
VACUUMING OPERATION
EXHAUST FLAPPER: Discharging into enclosed container,
position exhaust flapper to desired opening and secure
adjustment knob before starting engine. NOTE: An enclosed
container must capture all debris delivered into it preventing
any debris from blowing back onto unit's engine (see page 1
optional accessories).
Hose Bands.
Hose
Stretch hose
out before
fig. 2
clamping.
NOZZLE: With machine running and fully assembled, move
nozzle in sweeping motions over debris. For maximum pickup,
move nozzle close to debris, but without blocking air flow into
the nozzle (see figure 1). NOTE: Never bury nozzle into debris.
Page 5 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 811237
Form No. F050304A
OPERATION continued
16
16.6
HOSE OPERATION TIPS continued
UNCLOGGING A CLOGGED HOSE:
With engine running and unit secured to tailgate, fully stretch
hose in a straight line to dislodge the clog.
If the clog will not clear, turn unit off, and allow engine to come
to a complete stop. Remove hose and manually clear hose
clog.
UNCLOGGING A CLOGGED HOUSING OR
EXHAUST ELBOW:
Turn engine off and wait for impeller to come to a
complete stop. Disconnect spark plug wire.
Danger, the clog may contain sharp materials.
Wearing durable gloves, clear the clog.
Reconnect spark plug wire.
HOSE LIFE:
To increase hose life, periodically rotate hose and reposition
nozzle and coupler on front plate of unit. This increases hose
life by keeping hose from wearing only on one side.
HEAVY DEBRIS REMOVAL
TILT NOZZLE FORWARD TO PICK UP DIFFICULT DEBRIS.
Page 6 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 811237
Form No. F050304A
OPERATION continued
16
16.4
HANDLING & TRANSPORTING:
ALWAYS REMOVE LOADER FROM TAILGATE OR MOUNT-
ING BEFORE TRANSPORTING OR OPENING TAILGATE.
Using two people to lift machine is recommended. Lift holding
the rear handle and front of frame. Secure in place during
transport.
HOSE: DO NOT drag the hose with vehicle.
16.5
STORAGE
Turn fuel supply off when unit is not in use.
Never store engine indoors or in enclosed poorly ventilated
areas with fuel in tank, where fuel fumes may reach an open
flame, spark or pilot light, as on a furnace, water heater,
clothes dryer or other gas appliance.
If engine is to be unused for 30 days or more, prepare as
follows:
Be sure engine is cool. Do not smoke. Remove all
gasoline from carburetor and fuel tank to prevent gum deposits
from forming on these parts and causing possible malfunction
of engine. Drain fuel outdoors, into an approved container, away
from open flame. Run engine until fuel tank is empty and
engine runs out of gasoline.
NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable
alternative in minimizing the formation of fuel gum deposits
during storage. Add stabilizer to gasoline in fuel tank or storage
container. Always follow mix ratio found on stabilizer container.
Run engine at least 10 min. after adding stabilizer to allow it to
reach the carburetor.
HOSE STORAGE: Storing hose in a covered area, out of
sunlight and heat will prolong hose life. Do not store hose
where it could be stepped on or where other objects could crush
or damage hose.
Page 7 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 811237
Form No. F050304A
17
MAINTENANCE
17.1
IMPELLER REMOVAL
Use only a qualified mechanic for
any adjustments, disassembly or any
kind of repair .
1. Wait for engine to cool and disconnect spark plug.
2. Disconnect hose from unit.
3. Remove boom assembly.
WARNING: TO AVOID PERSONAL INJURY, ALWAYS
TURN MACHINE OFF, MAKE SURE ALL MOVING
PARTS COME TO A COMPLETE STOP.
4. Remove cable assy. interlock (item 43), from front plate of
assembly (item 41).
5. Remove front plate assembly (item 41).
6. Remove impeller bolt (item 16) and lock washer (item 17).
7. Pull the impeller outward. If impeller slides freely, proceed to (steps
10 to 14 for TR units or to step 14 for HTR units). If not, complete
steps 8 thru 9 as required.
DISCONNECT SPARK PLUG WIRE
BEFORE SERVICING UNIT.
8 . Place two crowbars between impeller and housing on opposite
sides. Pry impeller away from engine until it loosens. Using a
penetrating oil can help loosen a stuck impeller.
ENGINE: See engine manufacturer
operator's instructions.
9. If the impeller does not loosen, obtain a 1” (25.4mm) longer bolt
of the same diameter and thread type as the impeller bolt. Thread
longer bolt by hand into the crankshaft until bolt bottoms. Using a
suitable gear or wheel puller against the bolt head and the impeller
back-plate (near the blades), remove impeller from shaft.
10. [TR ONLY] Remove engine base mounting bolts, and nuts.
11. [TR ONLY] Access engine bolts on inside of housing that
connect engine face to the fan housing. Bend ends of lock clip away
from bolt heads and remove bolts.
12. [TR ONLY] Slide engine shaft out of impeller.
13. [TR ONLY] When impeller is free of the engine shaft, align
impeller with opening, and diagonally lift impeller out of housing.
14. Using a new impeller bolt and lockwasher (and engine bolt lock
clip, TR only), reinstall (engine for TR only) and new impeller in
reverse order.
RECONNECT SPARK PLUG WIRE,
GUARDS AND HOSE BEFORE START-
ING ENGINE.
Remove and Service foam air cleaner and inner air filter every 25
hours of use or every 10 hours or less for extremely dusty condi-
tions (see engine manual).
Keep engine and engine cooling fins clean from dust and debris
build-up.
Replace any worn or damaged parts as required.
DO NOT operate if excessive vibration occurs. If excessive vibration
occurs, shut engine off immediately. Remove spark plug wire and
check for damaged impeller, loose impeller bolt, loose impeller key
or lodged foreign objects. Refer to parts list (item 16) on page 11 for
proper torque specifications.
15. Tighten impeller bolt. Torque HTR1803VEU and TR1304HEU
.
impeller bolt to [ 50 Ft. Lbs. (68 N m)] and TR1104EU to [ 60 Ft. Lbs.
.
(81.4 N m)] (see item 16 on page 11).
16. Reinstall spark plug wire.
ENGINE
When servicing engine refer to specific manufacturers engine
owner's manual. All engine warranty is covered by the specific
engine manufacturer. If your engine requires warranty or other
repair work contact your local servicing engine dealer. When
contacting a dealer for service it is a good idea to have your
engine model number available for reference(See table page 11).
If you can not locate a servicing dealer in your area you can
contact the manufacturers national service organization.
To reach:
Briggs & Stratton: 800-233-3723
American Honda: 800-426-7701
Page 8 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 811237
Form No. F050304A
17
MAINTENANCE continued
Follow these hourly
maintenance intervals.
17. 3
INTERLOCK SYSTEM
Maintenance Schedule
17. 2
Every
Use
Every 5 hrs Every 10 Every 25
hrs
Maintenance Operation
or (Daily)
hrs
With hose coupler installed (as shown in Fig. 4) the switch is open
& engine is not grounded out, allowing engine to run.
Engine (See Engine Manual)
Check for excessive vibration
Clean Hose
HTR1803VEU SYSTEM
INTERLOCK
SWITCH
Item 43
Keep engine free of debris
Inspect for loose parts
Spark Plug
Spark Plug
Inspect for worn or damaged parts
Grease (see page 10)
A
ENGINE
SWITCH
TR1304HEU SYSTEM
OIL
ALERT
MAINTENANCE HISTORY
Date of Service
IGNITION
SWITCH
Service Performed
SPARK
PLUG
INTERLOCK
SWITCH
ITEM 43
OIL LEVEL
PLUG
TR1104EU SYSTEM
THROTTLE
STOP
SPARK
PLUG
ENGINE
INTERLOCK
SWITCH
SWITCH
ITEM 43
Fig. 3
Fig. 4
Page 9 of 12
Part No. 811237
Form No. F050304A
Download from Www.Somanuals.com. All Manuals Search And Download.
A
SEE PAGE 9
MAINTENANCE
18
PARTS DRAWING
HTR1803VEU, TR1304HEU,
TR1104EU
Page 10 of 12
Part No. 811237
Form No. F050304A
Download from Www.Somanuals.com. All Manuals Search And Download.
19
* Denotes standard
hardware item that may
be purchased locally.
Parts List
Denotes parts found in
parts bag assembly.
HTR1803VEU
TR1304HEU
PA RT NO.
811174
8164005
400424
*8172008
*8160002
*8171003
811123
811111
*8024050
811191
811233
810953
400339
810974
890301
- - -
810932
- - -
400502
- - -
*9201125
- - -
810736
830112
TR1104EU
PA RT NO.
811174
8164005
400424
*8172008
*8160002
*8171003
811123
811111
*8024050
811191
811233
810953
400339
810629
890301
- - -
- - -
500188
- - -
850132
- - -
*9201123
810736
830112
ITEM
DESCRIPTION
QTY
QTY
QTY
PA RT NO.
811174
-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
FLAPPER 8" INTAKE W/ LABEL
NUT LOCK 10-24
1
-
2
13
22
47
1
1
1
1
1
1
2
2
11
20
47
1
1
1
1
1
1
2
1
1
- -
1
- -
1
- -
1
- -
2
1
2
2
11
20
47
1
1
1
1
1
1
2
1
1
- -
- -
1
- -
1
- -
1
2
1
- -
2
1
1
2
- -
1
- -
4
- -
- -
1
2
2
2
2
2
2
4
18
- -
- -
1
2
1
2
1
3
2
2
1
1
2
1
1
5
1
2
2
2
1
1
1
2
1
LABEL DANGER KEEPHANDS AND FEET AWAY
WASHER 5/16 SAE(11/32 ID x 11/16 OD x 1/16)
NUT LOCK 5/16-18
WASHER 5/16 FLAT CUT (3/8 I.D. x 7/8 O.D. x 1/16)
PLUG 3/4"
400424
*8172008
*8160002
*8171003
811123
811111
*8024050
811191
811233
810953
400339
810930
890301
810962
- - -
- - -
400502
- - -
*9201125
- - -
810736
830112
811059
830533
811218
811235
811120
*8024045
DEFLECTOR EXHAUST 7"
CARRIAGEBOLT 5/16-18 x 3 1/2
ELBOW ASSY TR/HTR
GRIP HANDLE 3/4" ID 2" LONG BLACK
TUBE CLAMP
1
2
1
1
KNOB
IMPELLER ASSY (INCLUDES 16(1),17(1),18(1), 20(1))
LABEL READ OWNER'S MANUAL
SCREW CAP 3/8-24 x 2" GR 8 [50 Ft. Lbs. (68 N.m)]
SCREW CAP 3/8 - 24 X 2 1/4 GR 8 [50 Ft. Lbs. (68 N.m)]
SCREW CAP 7/16 - 20 X 2 GR 5 [60 Ft. Lbs. (81.4 N.m)]
WASHER LOCK 3/8 TWISTED TOOTH
WASHER LOCK 7/16 TWISTED TOOTH
KEY SQ. 1/4 x 2 3/4
1
- -
- -
1
- -
1
- -
2
1
1
2
1
1
2
1
- -
4
- -
1
- -
- -
2
2
2
2
2
2
4
18
3
1
1
2
1
2
1
3
2
2
1
1
17
18
KEY SQ. 1/4 X 2 1/4
LABEL DANGER FLYING MATERIAL
SPA CER IMPELLER
GUARD MANIFOLD
GUIDESTARTER ROPE (HALF)
TUBE REAR FRAME
19
20
21
22
23
24
25
26
1
- -
2
1
1
2
- -
1
-
-
-
-
-
-
830533
811218
811235
811120
830533
811218
811235
811120
COUPLER HOSEW/GRIP
PAD FRAME SHORT
CARRIAGEBOLT 5/16-18 x 2 1/4
CARRIAGEBOLT 5/16-18 x 4 1/2
SCREW CAP 5/16-18 x 1 1/2
SCREW CAP 5/16-18 x 2 1/2
ENGINE 18 H.P. VN W\CONTROL PANEL
ENGINE HONDA 13HP
-
-
-
-
-
-
-
-
-
*8024054
*8041030
*8024054
- - -
*8041034
- - -
27
28
*8041030
4
-
-
-
-
-
-
- -
- -
1
- -
2
2
2
2
2
2
4
18
-
-
1
2
1
2
1
3
2
2
1
1
2
1
1
5
1
2
2
2
1
1
811224
- - -
- - -
- - -
430366
- - -
- - -
ENGINE BRIGGS 11 HPINTEK I/C
KNOB PLASTIC 5/15 NUT INSERT
NUT LOCK W.A.
WASHER 3/4, PLASTIC
STUD 3/4 -10 x 5 1/2
SCREW MACHINE #10-24 x 2
PIN COTTER 1/8 x 1"
WASHER 3/8 SAE
NUT LOCK 3/8-16
SCREW SHEET METAL 1/4 AB x 3/4
GUARD MUFFLER
811205
850154
800227
800109
810954
*8059143
*8197031
*8172009
*8160003
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
850154
800227
800109
810954
*8059143
*8197031
*8172009
*8160003
*8122082
811058
810907
811122
811234
810535
890442
850200
610308-P
400332
830138
890254
811215
810870
810875
*8160001
810523
810878
*8041009
810880
810912
811009
850154
800227
800109
810954
*8059143
*8197031
*8172009
*8160003
-
-
-
-
-
-
-
-
-
-
-
-
BASE ENGINE
PA D FRAME LONG
810907
811122
811239
810535
890442
850200
610308-P
400332
830138
890254
811215
810870
810875
*8160001
810523
810878
*8041009
810880
810976
811009
810907
811122
811239
810535
890442
850200
610308-P
400332
830138
890254
811215
810870
810875
*8160001
810523
810878
*8041009
810880
810976
811009
430355
810566
811192
811121
810965
PLATEFRONT 8" TR W/INTERLOCK (INCL. 1,2,3,5(2),7,13,43,44,49,59,83,84,87,88)
PLUG CAP 1" SQUARE
CABLE ASSY SWITCH SV
CLIP-CABLE LIFT
WASHER-1.5 OD X 0.531 ID
SPRING COMPRESSION
LABEL CAUTION
LABEL EAR,EYE,BREATHING
LABEL WARNING ENGINEOVERHEAT
BOOM-PIVOT W.A.
2
1
1
5
1
2
2
2
1
1
-
2
1
1
1
TUBE-SQUAREBOOM ARM
NUT LOCK 1/4-20
HOSE 8" x 12.5' TR (COMES IN SEPERATE BOX)
CHAIN-LOOPASSY
SCREW CAP 1/4-20 x 1 3/4
BAND HOSEBOOM 8" TR
HOUSING ASSY W/LABELS (INCLUDES 35(2), 36(2), 45(2), 46(2), 47, 48, 90(2)
NOZZLE ASSY 8" TR (INCL. 4(2), 5(3), 6, 23, 77, 79(4), 80(2), 82, 83, 84
SPACER ENGINE INTEK
-
-
-
-
-
-
-
2
1
1
CLAMPHOSE8" TR
ELBOW EXHAUST WA
PAD FRAME CLAMP TUBE
810566
811192
811121
810927
810566
811192
811121
810965
1
1
SUPPORT PLATE ENGINE / SPACER ENG.
1
Page 11 of 12
Part No. 811237
Form No. F050304A
Download from Www.Somanuals.com. All Manuals Search And Download.
19
* Denotes standard
hardware item that may
be purchased locally.
Parts List
continued from
page 11.
HTR1803V EU
PA RT NO .
*8177012
TR1304HEU
PA RT NO .
*8177012
TR1104EU
PA RT NO .
ITEM
DESCRIPTIO N
Q TY
Q TY
Q TY
64
65
W A SHER LO CK 3/8
2
-
2
-
-
-
-
-
W A SHER LO CK 5/16 EXT. TO O TH
SCREW CA P 3/8 - 16 X 1
SCREW CA P 3/8 - 16 X 1 1/2 Z P
SCREW CA P 3/8 - 16 x 1"
SCREW CA P 1/4-20 X 1 1/2
SCREW CA P 3/8 - 16 X 1 3/4 Z P
A NGLE BRKT R.H.
-
-
-
-
-
-
-
*8181008
2
*8041050
2
-
-
-
-
-
-
-
-
-
-
-
-
-
-
8041052
*8041050
*8041008
*8041053
811096
2
8041052
*8041050
*8041008
*8041053
811096
2
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
*8041050
*8041008
*8041053
810917
12
12
1
4
1
2
1
1
1
1
2
2
1
1
4
3
1
1
4
4
1
1
1
1
2
2
1
12
1
4
1
2
1
1
1
1
2
2
1
1
4
3
1
1
4
4
1
1
1
1
2
2
1
1
4
1
2
1
1
1
1
SCREW CA P 5/16-18 x 1"
A NGLE BRKT L.H.
*8041028
810916
*8041028
810969
*8041028
810969
SPA CER
811097
811098
811098
W A SHER FLA T CUT 1/4
CO NTRO L THRO TTLE A SSY
SCREW MA CHINE 10-24 x 1-1/2"
NUT LO CK 5/16-18 THIN HT.
NO Z Z LE FO RMED STEEL 8"
HA NDLE NOZ Z LE W / GRIP
W A SHER FENDER 5/16
*8171002
810904-1
*8171002
811222
*8171002
811222
-
-
-
-
-
8059141
8161041
811007
8059141
8161041
811007
8161041
811007
811020
*8172020
*8041030
400268
811019
500267
890132
811100
811101
500282
890440
811139
811230
*8024216
2
1
1
4
3
1
1
4
4
1
1
1
1
2
2
1
811020
811020
*8172020
*8041030
400268
*8172020
*8041030
400268
SCREW CA P 5 /16 - 18 X 1 1/2
LA BEL DO NO T FILL W HEN ENG INE IS HOT
HA NDLE LO OP NOZ Z LE
G RIP HA NDLE
811019
811019
500267
500267
PLUG CA P
890132
890132
FRA ME SIDE RIG HT W A TR/HTR
FRA ME SIDE LEFT W A TR/HTR
STRA IN RELIEF
811100
811100
811101
811101
500282
500282
PLUNGER SW ITCH
890440
890440
TUBE HA NDLE LIFT
811139
811139
KNOB 3/8" SO LID HUB
811230
*8024216
811230
*8024216
BO LT CA RRIA GE 3/4 - 10 X 6" LONG
Before Requesting Service Review These Suggestions
TROUBLESHOOTING
20
Problem
Possible Cause
Solution
Adjust nozzle position. Unclog hose or exhaust (see page 6).
Allow air to feed with debris.
Will not vacuum or has poor
vacuum performance.
Nozzle height too high or too low. Clogged hose or exhaust.
Excessive quantity of debris.
Loose or out of balance impeller or loose engine.
Abnormal vibration.
Engine will not start.
Check impeller and replace if required. Check Engine.
Throttle & / or stop switch in off position. Out of gasoline. Bad or
old gasoline. Spark Plug wire disconnected. Dirty air cleaner.
Hose not installed, allowing interlock wire to ground.
Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Install hose onto housing.
See page 6, Clearing a clogged impeller housing. Contact an engine
servicing dealer for engine problems.
Debris locked inside impeller. Engine problem.
Engine is locked, will not
pull over.
WARRANTY PROCEDURE
Should a Billy Goat Machine fail due to a defect in material and/or
Engine Service and Warranty
Contact your nearest engine manufacturer's authorized
servicing dealer.
22.1
22
workmanship, the owner should make a warranty claim as follows:
Record your machine model, serial number and
Serial Plate
-The Machine must be taken to the dealer from whom it was purchased
or to an authorized Servicing Billy Goat Dealer.
21
date-of-purchase and where purchased
-The owner must present the remaining half of the Warranty Registra-
tion Card, or, if this is not available, the invoice or receipt.
-The Warranty Claim will be completed by the authorized Billy Goat
Dealer and submitted to their respective Billy Goat Distributor for their
territory. Attention: Service Manager. Any parts replaced under warranty
must be tagged and retained for 90 days.
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
R
-The distributor service manager will sign off on the claim and submit it
to Billy Goat for consideration.
Model
Serial No.
-The Technical Service Department at Billy Goat will study the claim and
may request parts to be returned for examination. Billy Goat will notify
their conclusions to the distributor service manager from whom the
claim was received.
-The decision by the Quality / Service department at Billy Goat to
approve or reject a Warranty claim is final and binding.
120 dB
(HTR1803VEU
MODEL)
Unit(Weight)
lbs.
Engine Power
kW
kg
rpm
min-1
Note: To process a Warranty Claim, it is necessary to quote the Model & Serial
Number which are printed on the Billy Goat Serial Plate (See owner’s manual).
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON STREET / LEE'S SUMMIT, MO 64082-2312 / USA
Purchased
from
Purchase
Date
PHONE: 816-524-9666 FAX: 816-524-6983
Page 12 of 12
Part No. 811237
Form No. F050304A
Download from Www.Somanuals.com. All Manuals Search And Download.
|