BenQ Projector MW817ST User Manual

MX815ST/MX815ST+/MX816ST/  
MW817ST  
Digital Projector  
User Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important safety instructions  
Your projector is designed and tested to meet the latest standards for safety of information  
technology equipment. However, to ensure safe use of this product, it is important that  
you follow the instructions mentioned in this manual and marked on the product.  
Safety Instructions  
1.  
Please read this manual before  
you operate your projector. Save  
it for future reference.  
5.  
In some countries, the line voltage is  
NOT stable. This projector is  
designed to operate safely within a  
mains voltage between 100 to 240  
volts AC, but could fail if power cuts  
or surges of ±10 volts occur. In  
areas where the mains voltage  
may fluctuate or cut out, it is  
recommended that you connect  
your projector through a power  
stabilizer, surge protector or  
uninterruptible power supply  
(UPS).  
2.  
Do not look straight at the  
projector lens during operation.  
The intense light beam may damage  
your eyes.  
6.  
Do not block the projection lens with  
any objects as this could cause the  
objects to become heated and  
deformed or even cause a fire. To  
temporarily turn off the lamp, press  
ECO BLANK on the projector or  
remote control.  
3.  
Refer servicing to qualified  
service personnel.  
4.  
Always open the lens shutter (if  
any) or remove the lens cap (if  
any) when the projector lamp is  
on.  
Important safety instructions  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Safety Instructions (Continued)  
7.  
The lamp becomes extremely hot  
during operation. Allow the projector  
to cool for approximately 45 minutes  
prior to removing the lamp assembly  
for replacement.  
10. Do not place this product on an  
unstable cart, stand, or table. The  
product may fall, sustaining serious  
damage.  
11. Do not attempt to disassemble this  
projector. There are dangerous high  
voltages inside which may cause death  
if you should come into contact with  
live parts. The only user serviceable  
part is the lamp which has its own  
removable cover.  
8.  
Do not operate lamps beyond the  
rated lamp life. Excessive operation of  
lamps beyond the rated life could  
cause them to break on rare  
occasions.  
Under no circumstances should you  
ever undo or remove any other  
covers. Refer servicing only to  
suitably qualified professional service  
personnel.  
9.  
Never replace the lamp assembly or  
any electronic components unless the  
projector is unplugged.  
12. When the projector is under  
operation, you may sense some  
heated air and odor from its  
ventilation grill. It is a normal  
phenomenon and not a product  
defect.  
4
Important safety instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Instructions (Continued)  
13. Do not place this projector in any of 14. Do not block the ventilation holes.  
- Do not place this projector on a  
blanket, bedding or any other soft  
surface.  
- Do not cover this projector with a cloth  
or any other item.  
- Do not place inflammables near the  
projector.  
the following environments.  
- Space that is poorly ventilated or  
confined. Allow at least 50 cm  
clearance from walls and free flow of air  
around the projector.  
- Locations where temperatures may  
become excessively high, such as the  
inside of a car with all windows rolled  
up.  
- Locations where excessive humidity,  
dust, or cigarette smoke may  
contaminate optical components,  
shorten the projector's life span and  
darken the image.  
If the ventilation holes are seriously  
obstructed, overheating inside the  
projector may result in a fire.  
15. Always place the projector on a level,  
horizontal surface during operation.  
- Do not use if tilted at an angle of more  
than 10 degrees left to right, nor at  
angle of more than 15 degrees front to  
back. Using the projector when it is not  
fully horizontal may cause a malfunction  
of, or damage to, the lamp.  
- Locations near fire alarms  
- Locations with an ambient temperature  
above 40°C / 104°F  
- Locations where the altitudes are higher  
than 3000 m (10000 feet).  
3000 m  
(10000 feet)  
16. Do not stand the projector on end  
vertically. Doing so may cause the  
0 m  
(0 feet)  
projector to fall over, causing injury or  
resulting in damage to the projector.  
Important safety instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Safety Instructions (Continued)  
17. Do not step on the projector or place  
any objects upon it. Besides probable  
physical damage to the projector, doing  
so may result in accidents and possible  
injury.  
Ceiling mounting the projector  
We want you to have a pleasant  
experience using your BenQ projector,  
so we need to bring this safety matter  
to your attention to prevent possible  
damage to person and property.  
If you intend to mount your projector  
on the ceiling, we strongly recommend  
that you use a proper fitting BenQ  
projector ceiling mount kit and that  
you ensure it is securely and safely  
installed.  
If you use a non-BenQ brand projector  
ceiling mount kit, there is a safety risk  
that the projector may fall from the  
ceiling due to an improper attachment  
through the use of the wrong gauge or  
length screws.  
18. Do not place liquids near or on the  
projector. Liquids spilled into the  
projector may cause it to fail. If the  
projector does become wet,  
disconnect it from the power supply's  
power outlet and call BenQ to have  
the projector serviced.  
You can purchase a BenQ projector  
ceiling mount kit from the place you  
purchased your BenQ projector. BenQ  
recommends that you also purchase a  
separate Kensington lock compatible  
security cable and attach it securely to  
both the Kensington lock slot on the  
projector and the base of the ceiling  
mount bracket. This will perform the  
secondary role of restraining the  
projector should its attachment to the  
mounting bracket become loose.  
19. This product is capable of displaying  
inverted images for ceiling mount  
installation.  
Hg - Lamp contains mercury. Manage in  
accordance with local disposal laws. See  
Use only BenQ's Ceiling Mount Kit for  
mounting the projector and ensure it is  
securely installed.  
20. This apparatus must be earthed.  
6
Important safety instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Projector features  
The projector integrates high-performance optical engine projection and a user-friendly  
design to deliver high reliability and ease of use.  
The projector offers the following features.  
Network Settings allowing management of projector status from a computer using a  
web browser  
®
ECO BLANK - With Philips ImageCare technology, the Eco Blank function will save  
up to 70% of your lamp power at the same time your image is hiding  
3D function to enjoy the 3D movies, videos, and sporting events in a more realistic way  
by presenting the depth of the images  
Brilliant color / VIDI to provide truer, more vibrant colors in picture  
Closed captioning to display the dialogue, narration, and sound effects of TV programs  
and videos  
Variable audio output  
Wall color correction allowing projection on surfaces of several predefined colors  
Quick auto search speeding up the signal detecting process  
Selectable password protected function  
3D color management allowing color adjustments to your liking  
Selectable quick cooling function making the projector cool in a shorter time  
Presentation timer for better control of time during presentations  
One-key auto-adjustment to display the best picture quality  
Digital keystone correction to correct distorted images  
Adjustable color balance control for data/video display  
Ability to display 1.07 billion colors  
Multi-language On-Screen Display (OSD) menus  
Switchable normal and economic modes to reduce the power consumption  
Built-in speaker providing mixed mono audio when an audio input is connected  
Component HDTV compatibility (YPbPr)  
The apparent brightness of the projected image will vary depending on the ambient lighting conditions,  
selected input signal contrast/brightness settings, and is directly proportional to projection distance.  
The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This  
is normal and expected behavior.  
Introduction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
   
Shipping contents  
Carefully unpack and verify that you have all of the items shown below. If any of these items  
are missing, please contact your place of purchase.  
Standard accessories  
The supplied accessories will be suitable for your region, and may differ from those illustrated.  
*The warranty card is only supplied in some specific regions. Please consult your dealer for detailed  
information.  
Projector  
Power cord  
VGA cable  
Quick start guide  
User manual CD  
Warranty card*  
Remote control with battery  
Pull the tab before using the remote control.  
Optional accessories  
1.  
2.  
Spare lamp kit  
Wall mount kit  
3.  
4.  
RS232 cable  
Soft carry case  
8
Introduction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Projector exterior view  
1.  
2.  
Lamp cover  
Front/upper side  
External control panel  
(See "Controls and functions" on page 10  
for details.)  
Vent (heated air exhaust)  
Quick-release button  
Focus ring  
Vent (cool air intake)  
Speaker grill  
Front IR remote sensor  
Projection lens  
2
1
3.  
4.  
5.  
6.  
7.  
8.  
9.  
3
5
6
7
4
8
9
10. Lens cap  
11. AC power jack  
10  
12. Rear adjuster foot  
13. Ceiling mount holes  
14. Front adjuster foot  
15. RS232 control port  
16. RJ45 LAN input jack  
17. USB port  
Rear/lower side  
18. Rear IR remote sensor  
19. HDMI-input port  
20. RGB signal output jack  
21. RGB (PC)/Component Video (YPbPr/  
YCbCr) signal input jack  
22. S-Video input jack  
Video input jack  
23. Audio (L/R) input jacks  
24. Audio input jacks  
Audio output jack  
23 24  
20  
14  
21 22  
15 16 17 18 19  
11  
13  
25  
12  
25. Kensington anti-theft lock slot  
Introduction  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Projector  
6.  
7.  
8.  
TEMPerature warning light  
Lights up red if the projector's  
temperature becomes too high.  
POWER indicator light  
1
6
Lights up or flashes when the projector is  
under operation.  
7
Keystone/Arrow keys (  
Down)  
/
Up,  
/
2
3
4
8
9
10  
11  
12  
Manually corrects distorted images  
resulting from an angled projection.  
Auto  
5
9.  
13  
8
Automatically determines the best picture  
timings for the displayed image.  
1.  
2.  
Focus ring  
10.  
Right/  
Adjusts the focus of the projected image.  
LAMP indicator light  
Increases the projector volume.  
Indicates the status of the lamp. Lights up  
or flashes when the lamp has developed a  
problem.  
When the On-Screen Display (OSD)  
menu is activated, the #4, #8, and #10  
keys are used as directional arrows to  
select the desired menu items and to  
make adjustments.  
3.  
MENU/EXIT  
Turns on the On-Screen Display (OSD)  
menu. Goes back to previous OSD menu,  
exits and saves menu settings.  
11.  
POWER  
Toggles the projector between standby  
mode and on.  
4.  
5.  
Left/  
12. MODE/ENTER  
Decreases the projector volume.  
ECO BLANK  
Selects an available picture setup mode.  
Used to hide the screen picture.  
Activates the selected On-Screen Display  
(OSD) menu item.  
13. SOURCE  
Displays the source selection bar.  
10  
Introduction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                             
Remote control  
9.  
Keystone/Arrow keys (  
Down)  
/
Up,  
/
8
9
Manually corrects distorted images  
resulting from an angled projection.  
1
2
10  
11  
12  
13  
9
14  
15  
16  
10. Auto  
Automatically determines the best  
picture timings for the displayed image.  
3
4
5
6
11.  
Right  
When the On-Screen Display (OSD)  
menu is activated, the #3, #9, and #11  
keys are used as directional arrows to  
select the desired menu items and to  
make adjustments.  
7
12. SOURCE  
Displays the source selection bar.  
13. MODE/ENTER  
Selects an available picture setup mode.  
1.  
2.  
POWER  
Toggles the projector between standby  
mode and on.  
Activates the selected On-Screen  
Display (OSD) menu item.  
Freeze  
14. Timer On  
Freezes the projected image.  
Left  
SMART ECO  
Activates or displays an on-screen timer  
based on your own timer setting.  
3.  
4.  
15. Timer Set up  
Displays the lamp mode selection bar.  
ECO BLANK  
Enters presentation timer setting  
directly.  
5.  
6.  
Used to hide the screen picture.  
Digital Zoom (+, -)  
16. PAGE UP/PAGE DOWN  
Operate your display software program  
(on a connected PC) which responds to  
page up/down commands (like Microsoft  
PowerPoint).  
Magnifies or reduces the projected picture  
size.  
Volume +/-  
7.  
8.  
Adjusts the sound level.  
MENU/EXIT  
Turns on the On-Screen Display (OSD)  
menu. Goes back to previous OSD menu,  
exits and saves menu settings.  
Introduction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
     
Remote control effective range  
Infra-Red (IR) remote control sensors are located on the front and back of the projector.  
The remote control must be held at an angle within 30 degrees perpendicular to the  
projector's IR remote control sensors to function correctly. The distance between the  
remote control and the sensors should not exceed 8 meters (~ 26 feet).  
Make sure that there are no obstacles between the remote control and the IR sensors on  
the projector that might obstruct the infra-red beam.  
Operating the projector from the front  
Operating the projector from the rear  
Replacing the remote control battery  
1.  
Pull out the battery holder.  
Please follow the illustrated instructions. Push and hold the locking  
arm while pulling out the battery holder.  
2.  
Insert the new battery in the holder. Note the  
positive polarity should face outward.  
3.  
Push the holder into the remote control.  
Avoid excessive heat and humidity.  
There may be battery damage if the battery is incorrectly  
replaced.  
Replace only with the same or equivalent type recommended by  
the battery manufacturer.  
Dispose of the used battery according to the battery  
manufacturer's instructions.  
Never throw a battery into a fire. There may be danger of an explosion.  
If the battery is dead or if you will not be using the remote control for a long time, remove the battery to  
prevent damage to the remote control from possible battery leakage.  
12  
Introduction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Positioning your projector  
Choosing a location  
Your projector is designed to be installed in one of four possible installation locations:  
1.  
Front Table  
3.  
Rear Ceiling  
Select this location with the projector  
placed on the table in front of the screen.  
Select this location with the projector  
suspended upside-down from the ceiling  
This is the most common way to position behind the screen.  
the projector for quick setup and  
Note that a special rear projection screen  
and the BenQ Projector Ceiling Mount Kit  
are required for this installation location.  
portability.  
Set Rear Ceiling in the SYSTEM  
SETUP: Basic > Projector Position  
menu after you turn the projector on.  
2.  
Front Ceiling  
Select this location with the projector  
suspended upside-down from the ceiling in  
front of the screen.  
Purchase the BenQ Projector Ceiling  
Mount Kit from your dealer to mount your  
projector on the ceiling.  
4.  
Rear Table  
Select this location with the projector  
placed on the table behind the screen.  
Set Front Ceiling in the SYSTEM  
SETUP: Basic > Projector Position  
menu after you turn the projector on.  
Note that a special rear projection screen  
is required.  
Set Rear Table in the SYSTEM SETUP:  
Basic > Projector Position menu after  
you turn the projector on.  
Your room layout or personal preference will dictate which installation location you select.  
Take into consideration the size and position of your screen, the location of a suitable  
power outlet, as well as the location and distance between the projector and the rest of  
your equipment.  
Positioning your projector  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Obtaining a preferred projected image size  
The distance from the projector lens to the screen, the zoom setting, and the video format  
each factors in the projected image size.  
Projection dimensions  
Refer to "Dimensions" on page 54 for the center of lens dimensions of this projector  
before calculating the appropriate position.  
MX815ST/MX815ST+/MX816ST  
(a)  
Screen  
Center of lens  
(c)  
(b)  
The screen aspect ratio is 4:3 and the projected picture is 4:3  
(a) Screen size  
(b) Distance from screen  
(mm)  
(c) Vertical offset  
(mm)  
Diagonal  
Height  
(mm)  
1219  
1524  
2286  
2743  
3048  
3353  
3658  
4115  
4572  
Width  
(mm)  
1626  
2032  
3048  
3658  
4064  
4470  
4877  
5486  
6096  
Inches  
mm  
80  
2032  
2540  
3048  
3810  
4572  
5080  
5588  
6096  
6858  
7620  
988  
183  
229  
274  
343  
411  
457  
503  
549  
617  
686  
100  
120  
150  
180  
200  
220  
240  
270  
300  
1235  
1481  
1852  
2222  
2469  
2716  
2963  
3333  
3704  
For example, if you are using an 120-inch screen, the recommended projection distance is  
1481 mm and the vertical offset is 274 mm.  
If your measured projection distance is 2.5 m (2500 mm), the closest match in the "(b)  
Distance from screen" column is 2469 mm. Looking across this row shows that a 200''  
(about 5.1 m) screen is required.  
14  
Positioning your projector  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
MW817ST  
(a)  
Screen  
Center of lens  
(c)  
(b)  
The screen aspect ratio is 16:10 and the projected picture is 16:10  
(a) Screen size  
(b) Distance from screen  
(c) Vertical offset  
(mm)  
Diagonal  
Height  
(mm)  
1077  
1346  
2019  
2423  
2692  
2962  
3231  
3635  
4039  
Width  
(mm)  
1723  
2154  
3231  
3877  
4308  
4739  
5169  
5816  
6462  
(mm)  
Inches  
80  
mm  
2032  
2540  
3048  
3810  
4572  
5080  
5588  
6096  
6858  
7620  
842  
54  
67  
81  
101  
121  
135  
148  
162  
182  
202  
100  
120  
150  
180  
200  
220  
240  
270  
300  
1053  
1263  
1579  
1895  
2105  
2316  
2526  
2842  
3158  
For example, if you are using an 120-inch screen, the recommended projection distance is  
1263 mm and the vertical offset is 81 mm.  
If your measured projection distance is 2.5 m (2500 mm), the closest match in the "(b)  
Distance from screen" column is 2526 mm. Looking across this row shows that a 240''  
(about 6.1 m) screen is required.  
All measurements are approximate and may vary from the actual sizes.  
BenQ recommends that if you intend to permanently install the projector, you should physically test the  
projection size and distance using the actual projector in situ before you permanently install it, so as to make  
allowance for this projector's optical characteristics. This will help you determine the exact mounting position  
so that it best suits your installation location.  
Positioning your projector  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connection  
When connecting a signal source to the projector, be sure to:  
1.  
2.  
3.  
Turn all equipment off before making any connections.  
Use the correct signal cables for each source.  
Ensure the cables are firmly inserted.  
In the connections shown below, some cables may not be included with the projector (see "Shipping  
contents" on page 8). They are commercially available from electronics stores.  
The connection illustrations below are for reference only. The rear connecting jacks available on the  
projector vary with each projector model.  
Notebook or desktop computer  
A/V device  
Monitor  
(VGA)  
(DVI)  
Speakers  
9
7
8
1
2
3
1
9
4
5
9
6
or  
or  
1.  
VGA cable  
VGA to DVI-A cable  
USB cable  
HDMI cable  
Component Video to VGA (D-Sub)  
adapter cable  
6.  
7.  
8.  
9.  
Audio L/R cable  
S-Video cable  
Video cable  
2.  
3.  
4.  
5.  
Audio cable  
16  
Connection  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Many notebooks do not turn on their external video ports when connected to a projector. Usually a key  
combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/  
LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled function key  
simultaneously. Refer to your notebook's documentation to find your notebook's key combination.  
The D-Sub output only works when an appropriate D-Sub input is made to the COMPUTER 1 jack.  
If you wish to use this connection method when the projector is in standby mode, make sure the  
Monitor Out function is turned on in the SYSTEM SETUP: Advanced menu. See "Standby Settings"  
on page 43 for details.  
Connecting video source devices  
You need only connect the projector to a video source device using just one of the  
connecting methods, however each provides a different level of video quality. The method  
you choose will most likely depend upon the availability of matching terminals on both the  
projector and the video source device as described below:  
Term inal name  
HDMI  
Terminal appearance  
Picture quality  
Best  
Component Video  
S-Video  
Better  
Good  
Video  
Normal  
Connecting audio  
The projector has one built-in mono speaker which is designed to provide basic audio  
functionality accompanying data presentations for business purposes only. It is not designed  
for, nor intended for stereo audio reproduction use as might be expected in home theater  
or home cinema applications. Any stereo audio input (if provided), is mixed into a common  
mono audio output through the projector speaker.  
The built-in speaker will be muted when the AUDIO OUT jack is connected.  
In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI input and  
the projected picture displays wrong colors, please change the color space to YUV. See "Changing Color  
Space" on page 25 for details.  
The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See  
"Connecting audio" on page 17 for details.  
If the selected video image is not displayed after the projector is turned on and the correct video source  
has been selected, check that the video source device is turned on and operating correctly. Also check  
that the signal cables have been connected correctly.  
Connection  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
   
Operation  
Starting up the projector  
1.  
Plug the power cord into the projector and into a  
power outlet. Turn on the power outlet switch  
(where fitted). Check that the POWER indicator  
light on the projector lights orange after power  
has been applied.  
Please use the original accessories (e.g. power cord) only with the  
device to avoid possible dangers such as electric shock and fire.  
2.  
Press  
POWER on the projector or  
ON on the remote control to start the  
projector. As soon as the lamp lights up, a "Power On Tone" will be heard. The  
POWER indicator light flashes green and stays green when the projector is on.  
The start up procedure takes about 30 seconds. In the later stage of start up, a  
startup logo is projected.  
(If necessary) Rotate the focus ring to adjust the image clearness.  
To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 34  
for details.  
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds  
before energizing the lamp.  
3.  
If the projector is activated for the first time,  
select your OSD language following the on-  
screen instructions.  
4.  
If you are prompted for a password, press the  
arrow keys to enter a six-digit password. See  
"Utilizing the password function" on page 22 for  
details.  
5.  
6.  
Switch all of the connected equipment on.  
The projector will start to search for input  
signals. The current input signal being scanned  
displays in the upper left corner of the screen. If  
the projector doesn't detect a valid signal, the message “No Signal” will continue  
displaying until an input signal is found.  
You can also press SOURCE on the projector or remote control to select your  
desired input signal. See "Switching input signal" on page 25 for details.  
If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the  
message “Out of Range” displayed on a blank screen. Please change to an input signal which is compatible with  
the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 58 for details.  
18  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Adjusting the projected image  
Adjusting the projection angle  
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot.  
These adjusters change the image height and projection angle. To adjust the projector:  
1.  
Press the quick-release button and lift the  
front of the projector. Once the image is  
positioned where you want it, release the  
quick-release button to lock the foot in  
position.  
2.  
Screw the rear adjuster foot to fine-tune the  
horizontal angle.  
1
2
To retract the foot, hold up the projector while  
pressing the quick-release button, then slowly lower  
the projector. Screw the rear adjuster foot in a  
reverse direction.  
Do not look into the lens while the  
lamp is on. The strong light from the  
lamp may cause damage to your eyes.  
Be careful when you press the quick-  
release button as it is close to the  
exhaust vent where hot air comes  
from.  
If the projector is not placed on a flat surface or the  
screen and the projector are not perpendicular to  
each other, the projected image becomes  
trapezoidal. To correct this situation, see "Switching  
input signal" on page 25 for details.  
Auto-adjusting the image  
In some cases, you may need to optimize the picture quality. To do this, press Auto on the  
projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment  
function will re-adjust the values of Frequency and Clock to provide the best picture  
quality.  
The current source information will be displayed in the corner of the screen for 3 seconds.  
This function is only available when PC signal (analog RGB) is selected.  
Fine-tuning the image clarity  
Sharpen the image by rotating the focus ring.  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
 
Correcting keystone  
Keystoning refers to the situation where the projected image is noticeably wider at either  
the top or bottom. It occurs when the projector is not perpendicular to the screen.  
To correct this, you will need to manually correct it following ONE of these steps.  
Using the remote control  
Press on the projector or remote control  
/
to display the Keystone correction page. Press  
to correct keystoning at the top of the image. Press  
to correct keystoning at the bottom of the  
image.  
Press  
/
.
Press  
/
.
Using the OSD menu  
1.  
2.  
Press MENU/EXIT and then press  
/
until the DISPLAY menu is highlighted.  
Press  
to highlight Keystone and press MODE/ENTER. The Keystone  
correction page displays.  
3.  
Press  
to correct keystoning at the top of the image. Press  
to correct  
keystoning at the bottom of the image.  
20  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using the menus  
The projector is equipped with On-Screen Display (OSD) menus for making various  
adjustments and settings.  
Below is the overview of the OSD menu.  
Main menu icon  
DISPLAY  
Main menu  
Off  
Wall Color  
Aspect Ratio  
Keystone  
Auto  
Position  
Phase  
ENTER  
Status  
0
0
Sub-menu  
H. Size  
Digital Zoom  
3D Sync  
Off  
Press MENU/  
EXIT to the  
previous  
page or to  
exit.  
3D Sync Invert  
Teaching Template  
Disable  
Highlight  
Current input signal  
MENU  
Exit  
Analog RGB  
The following example describes how to set the OSD language.  
1.  
Press MENU/EXIT on the projector or  
remote control to turn the OSD menu on.  
3.  
Press  
and press  
to highlight Language  
to select a  
/
preferred language.  
DISPLAY  
Wall Color  
Aspect Ratio  
Keystone  
Position  
Off  
Auto  
SYSTEM SETUP: Basic  
Presentation Timer  
Language  
English  
Phase  
H. Size  
0
0
Projector Position  
Menu Settings  
Front Table  
Digital Zoom  
3D Sync  
3D Sync Invert  
Operation Settings  
Panel Key Lock  
Background Color  
Splash Screen  
Off  
Disable  
Off  
BenQ  
BenQ  
Teaching Template  
MENU Exit  
Analog RGB  
MENU Exit  
Analog RGB  
4.  
Press MENU/EXIT twice* on  
the projector or remote control  
to leave and save the settings.  
2.  
Use  
/
to highlight the SYSTEM  
SETUP: Basic menu.  
SYSTEM SETUP: Basic  
*The first press leads you back to  
the main menu and the second  
press closes the OSD menu.  
Presentation Timer  
Language  
Projector Position  
Menu Settings  
English  
Front Table  
Operation Settings  
Panel Key Lock  
Off  
BenQ  
BenQ  
Background Color  
Splash Screen  
MENU Exit  
Analog RGB  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
 
Securing the projector  
Using a security cable lock  
The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a  
lock, such as the Kensington lock, to secure the projector. You can locate a Kensington  
lock slot on the rear side of the projector. See item 25 on page 9 for details.  
A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to  
the lock’s documentation for finding out how to use it.  
Utilizing the password function  
For security purposes and to help prevent unauthorized use, the projector includes an  
option for setting up password security. The password can be set through the On-Screen  
Display (OSD) menu.  
WARNING: You will be inconvenienced if you activate the password functionality and subsequently forget the  
password. Print out this manual (if necessary) and write the password you used in this manual, and keep the  
manual in a safe place for later recall.  
Setting a password  
Once a password has been set and the power on lock is activated, the projector cannot be used unless the  
correct password is entered every time the projector is started.  
1.  
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security  
Settings menu. Press MODE/ENTER. The Security Settings page displays.  
Highlight Change Security Settings and press MODE/ENTER.  
2.  
3.  
As pictured to the right, the four arrow keys  
INPUT NEW PASSWORD  
(
,
,
,
) respectively represent 4 digits  
Power On Lock and Splash Screen Lock  
use the same password.  
(1, 2, 3, 4). According to the password you  
desire to set, press the arrow keys to enter six  
digits for the password.  
4.  
Confirm the new password by re-entering the  
new password.  
Once the password is set, the OSD menu  
returns to the Security Settings page.  
To activate the Power On Lock function, press  
MENU Back  
5.  
6.  
/
to highlight Power On Lock  
and press  
To activate the Splash Screen Lock function, press  
Screen Lock and press to select On.  
/
to select On.  
/
to highlight Splash  
/
When the Splash Screen Lock is activated, the MyScreen function in the  
SYSTEM SETUP: Basic menu will be password-protected.  
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down  
here in this manual in advance or right after the password is entered so that it is available to you should you  
ever forget it.  
Password: __ __ __ __ __ __  
Keep this manual in a safe place.  
7.  
To leave the OSD menu, press MENU/EXIT.  
22  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
If you forget the password  
If the password function is activated, you will be asked  
to enter the six-digit password every time you turn on  
the projector. If you enter the wrong password, the  
password error message as pictured to the right  
displays lasting for 3 seconds, and the INPUT  
PASSWORD message follows. You can retry by  
entering another six-digit password, or if you did not  
Password Error  
Please try again.  
record the password in this manual, and you absolutely do not remember it, you can use  
the password recall procedure. See "Entering the password recall procedure" on page 23  
for details.  
If you enter an incorrect password 5 times in succession, the projector will automatically  
shut down in a short time.  
Entering the password recall procedure  
1.  
Press and hold Auto on the projector or  
remote control for 3 seconds. The  
projector will display a coded number on  
the screen.  
RECALL PASSWORD  
Please write down the recall code,  
and contact BenQ  
Customer Center.  
2.  
3.  
Write down the number and turn off your  
projector.  
Recall Code:  
0 2 1 2  
Seek help from the local BenQ service  
center to decode the number. You may be  
required to provide proof of purchase  
documentation to verify that you are an  
authorized user of the projector.  
MENU  
Exit  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
 
Changing the password  
1.  
2.  
3.  
Open the OSD menu and go to the SYSTEM SETUP: Advanced> Security  
Settings > Change Password menu.  
Press MODE/ENTER. The message “INPUT CURRENT PASSWORD”  
appears.  
Enter the old password.  
i. If the password is correct, another message “INPUT NEW PASSWORD”  
displays.  
ii. If the password is incorrect, the password error message displays lasting for  
three seconds, and the message “INPUT CURRENT PASSWORD” displays  
for your retry. You can press MENU/EXIT to cancel the change or try another  
password.  
4.  
Enter a new password.  
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down  
here in this manual in advance or right after the password is entered so that it is available to you should you  
ever forget it.  
Password: __ __ __ __ __ __  
Keep this manual in a safe place.  
5.  
6.  
Confirm the new password by re-entering the new password.  
You have successfully assigned a new password to the projector. Remember to enter  
the new password next time the projector is started.  
7.  
To leave the OSD menu, press MENU/EXIT.  
Disabling the password function  
To disable password protection, go back to the SYSTEM SETUP: Advanced >  
Security Settings > Change Security Settings menu after opening the OSD menu  
system. Press MODE/ENTER. The message “INPUT PASSWORD” displays. Enter  
the current password.  
i. If the password is correct, the OSD menu returns to the Security Settings  
page.  
Press  
not have to enter the password next time when turning on the projector.  
Press to highlight Splash Screen Lock and press to select Off. You  
to highlight Power On Lock and press  
/
to select Off. You will  
/
will not have to enter the password next time when turning on the projector.  
The Splash Screen function in the SYSTEM SETUP: Basic menu will be  
available for your change.  
ii. If the password is incorrect, the password error message displays lasting for  
three seconds, and the message “INPUT PASSWORD” displays for your  
retry. You can press MENU/EXIT to cancel the change or try another  
password.  
Though the password function is disabled, you need to keep the old password in hand should you ever need to  
re-activate the password function by entering the old password.  
24  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switching input signal  
The projector can be connected to multiple devices at the same time. However, it can only  
display one full screen at a time. When starting up, the projector automatically searches for  
the available signals.  
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the  
projector to automatically search for the signals.  
To select the source:  
Computer1/YPbPr1  
1.  
Press SOURCE on the projector or remote  
control. A source selection bar displays.  
2.  
Press  
/
until your desired signal is selected  
Computer2/YPbPr2  
HDMI  
and press MODE/ENTER.  
Once detected, the selected source information  
seconds. If there is multiple equipment  
connected to the projector, repeat steps 1-2 to  
search for another signal.  
Video  
S-Video  
The brightness level of the projected image will change  
accordingly when you switch between different input signals.  
Data (graphic) "PC" presentations using mostly static images  
are generally brighter than "Video" using mostly moving  
images (movies).  
The native display resolution of this projector is in a 4:3 (MX815ST/MX815ST+/MX816ST)/16:10  
(MW817ST) aspect ratio. For best display picture results, you should select and use an input signal which  
outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the  
“aspect ratio” setting, which may cause some image distortion or loss of picture clarity. See "Selecting the  
aspect ratio" on page 26 for details.  
Changing Color Space  
In the unlikely event that you connect the projector to a DVD player via the projector’s  
HDMI input and the projected picture displays wrong colors, please change the color  
space to YUV.  
To do this:  
1.  
2.  
Press MENU/EXIT and then press  
Press to highlight Color Space Conversion and press  
color space.  
/
until the SOURCE menu is highlighted.  
/
to select a suitable  
This function is only available when the HDMI-input port is in use.  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
       
Magnifying and searching for details  
If you need to find the details on the projected picture, magnify the picture. Use the  
direction arrow keys for navigating the picture.  
Using the remote control  
1.  
Press Digital Zoom+/- to display the Zoom bar. Press Digital Zoom+ to magnify  
the center of the picture. Press the key repeatedly until the picture size is suitable for  
your need.  
2.  
3.  
Use the directional arrows (  
navigate the picture.  
To restore the picture to its original size, press Auto. You can also press Digital  
Zoom-. When the key is pressed again, the picture is further reduced until it is  
restored to the original size.  
,
,
,
) on the projector or remote control to  
Using the OSD menu  
1.  
2.  
Press MENU/EXIT and then press  
/
until the DISPLAY menu is highlighted.  
Press  
to highlight Digital Zoom and press MODE/ENTER. The Zoom bar  
displays.  
3.  
4.  
Press  
repeatedly to magnify the picture to a desired size.  
To navigate the picture, press MODE/ENTER to switch to the panning mode and  
press the directional arrows (  
navigate the picture.  
,
,
,
) on the projector or remote control to  
5.  
To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/  
out function, and press Auto to restore the picture to its original size. You can also  
press  
repeatedly until it is restored to the original size.  
The picture can only be navigated after it is magnified. You can further magnify the picture while  
searching for details.  
Selecting the aspect ratio  
The “aspect ratio” is the ratio of the image width to the image height. Most analog TV and  
some computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.  
With the advent of digital signal processing, digital display devices like this projector can  
dynamically stretch and scale the image output to a different aspect than that of the image  
input signal.  
To change the projected picture ratio (no matter what aspect the source is):  
1.  
2.  
3.  
Press MENU/EXIT and then press  
/
until the DISPLAY menu is highlighted.  
Press  
Press  
to highlight Aspect Ratio.  
/
to select an aspect ratio to suit the format of the video signal and your  
display requirements.  
26  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
About the aspect ratio  
In the pictures below, the black portions are inactive areas and the white portions are active areas.  
OSD menus can be displayed on those unused black areas.  
1.  
Auto: Scales an image proportionally  
to fit the projector's native resolution  
in its horizontal or vertical width. This  
is suitable for the incoming image  
which is neither in 4:3 nor 16:9 and  
you want to make most use of the  
screen without altering the image's  
aspect ratio.  
MW817ST  
MX815ST/  
MX815ST+/  
MX816ST  
15:9 picture  
2.  
Real: The image is projected as its  
original resolution, and resized to fit  
within the display area. For input  
signals with lower resolutions, the  
projected image will display smaller  
than if resized to full screen. You could  
adjust the zoom setting or move the  
projector towards the screen to  
increase the image size if necessary.  
You may also need to refocus the  
projector after making these  
4:3 picture  
16:9 picture  
adjustments.  
3.  
4:3: Scales an image so that it is  
displayed in the center of the screen  
with a 4:3 aspect ratio. This is most  
suitable for 4:3 images like some  
computer monitors, standard  
definition TV and 4:3 aspect DVD  
movies, as it displays them without  
aspect alteration.  
4:3 picture  
4.  
5.  
16:9: Scales an image so that it is  
displayed in the center of the screen  
with a 16:9 aspect ratio. This is most  
suitable for images which are already  
in a 16:9 aspect, like high definition TV,  
as it displays them without aspect  
alteration.  
16:9 picture  
16:10: Scales an image so that it is  
displayed in the center of the screen  
with a 16:10 aspect ratio. This is most  
suitable for images which are already  
in a 16:10 aspect, as it displays them  
without aspect alteration.  
16:10 picture  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
Optimizing the image  
Using Wall Color  
In the situation where you are projecting onto a colored surface such as a painted wall  
which may not be white, the Wall Color feature can help correct the projected picture’s  
colors to prevent possible color difference between the source and projected pictures.  
To use this function, go to the DISPLAY > Wall Color menu and press  
/
to select  
a color which is closest to the color of the projection surface. There are several  
precalibrated colors to choose from: Light Yellow, Pink, Light Green, Blue, and  
Blackboard.  
Selecting a picture mode  
The projector is preset with several predefined picture modes so that you can choose one  
to suit your operating environment and input signal picture type.  
To select an operation mode that suits your need, you can follow one of the following  
steps.  
Press MODE/ENTER on the projector or remote control repeatedly until your  
desired mode is selected.  
Go to the PICTURE > Picture Mode menu and press  
/
to select a desired  
mode.  
1.  
Dynamic mode: Maximizes the brightness of the projected image. This mode is  
suitable for environments where extra-high brightness is required, such as using the  
projector in well lit rooms.  
2.  
3.  
Presentation mode: Is designed for presentations. The brightness is emphasized in  
this mode to match PC and notebook coloring.  
sRGB mode: Maximizes the purity of RGB colors to provide true-to-life images  
regardless of brightness setting. It is most suitable for viewing photos taken with an  
sRGB compatible and properly calibrated camera, and for viewing PC graphic and  
drawing applications such as AutoCAD.  
4.  
5.  
Cinema mode: Is appropriate for playing colorful movies, video clips from digital  
cameras or DVs through the PC input for best viewing in a blackened (little light)  
environment.  
User 1/User 2 mode: Recalls the settings customized based on the current  
available picture modes. See "Setting the User 1/User 2 mode" on page 28 for details.  
Setting the User 1/User 2 mode  
There are two user-definable modes if the current available picture modes are not suitable  
for your need. You can use one of the picture modes (except the User 1/2) as a starting  
point and customize the settings.  
1.  
2.  
3.  
4.  
Press MENU/EXIT to open the On-Screen Display (OSD) menu.  
Go to the PICTURE > Picture Mode menu.  
Press  
Press  
/
to select User 1 or User 2.  
to highlight Reference Mode.  
This function is only available when User 1 or User 2 mode is selected up in the Picture Mode sub-menu  
item.  
5.  
Press  
/
to select a picture mode that is closest to your need.  
28  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
6.  
7.  
8.  
Press  
to select a menu item to be changed and adjust the value with  
/
. See  
"Fine-tuning the image quality in user modes" below for details.  
When all settings have been done, highlight Save Settings and press MODE/  
ENTER to store the settings.  
The confirmation message “Setting Saved” displays.  
Fine-tuning the image quality in user modes  
According to the detected signal type, there are some user-definable functions available  
when User 1 or User 2 is selected. Based on your needs, you can make adjustments to  
these functions by highlighting them and pressing  
control.  
/
on the projector or remote  
Adjusting Brightness  
The higher the value, the brighter the image. And the  
lower the setting, the darker the image. Adjust this  
control so the black areas of the image appear just as  
black and that detail in the dark areas is visible.  
+50  
+70  
+30  
Adjusting Contrast  
The higher the value, the greater the contrast. Use this  
to set the peak white level after you have previously  
adjusted the Brightness setting to suit your selected  
input and viewing environment.  
0
+30  
-30  
Adjusting Color  
Lower setting produces less saturated colors. If the setting is too high, colors on the image  
will be overpowering, which makes the image unrealistic.  
Adjusting Tint  
The higher the value, the more reddish the picture becomes. The lower the value, the  
more greenish the picture becomes.  
Adjusting Sharpness  
The higher the value, the sharper the picture becomes. The lower the value, the softer the  
picture becomes.  
Adjusting Brilliant Color  
This feature utilizes a new color-processing algorithm and system level enhancements to  
enable higher brightness while providing truer, more vibrant colors in picture. It enables a  
greater than 50% brightness increase in mid-tone images, which are common in video and  
natural scenes, so the projector reproduces images in realistic and true colors. If you  
prefer images with that quality, select On. If you don’t need it, select Off.  
When Off is selected, the Color Temperature function is not available.  
Selecting a color temperature  
The options available for color temperature* settings vary according to the signal type  
selected.  
1.  
2.  
3.  
Cool: Makes images appear bluish white.  
Normal: Maintains normal colorings for white.  
Warm: Makes images appear reddish white.  
*About color temperatures:  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
               
There are many different shades that are considered to be "white" for various purposes.  
One of the common methods of representing white color is known as the “color  
temperature”. A white color with a low color temperature appears to be reddish white. A  
white color with a high color temperature appears to have more blue in it.  
3D Color Management  
In most installation situations, color management will not be necessary, such as in  
classroom, meeting room, or lounge room situations where lights remain on, or where  
building external windows allow daylight into the room.  
Only in permanent installations with controlled lighting levels such as boardrooms, lecture  
theaters, or home theaters, should color management be considered. Color management  
provides fine color control adjustment to allow for more accurate color reproduction,  
should you require it.  
Proper color management can only be achieved under controlled and reproducible viewing  
conditions. You will need to use a colorimeter (color light meter), and provide a set of  
suitable source images to measure color reproduction. These tools are not provided with  
the projector, however, your projector supplier should be able to provide you with suitable  
guidance, or even an experienced professional installer.  
The Color Management provides six sets (RGBCMY) of colors to be adjusted. When you  
select each color, you can independently adjust its range and saturation according to your  
preference.  
If you have purchased a test disc which contains various color test patterns and can be  
used to test the color presentation on monitors, TVs, projectors, etc, you can project any  
image from the disc on the screen and enter the 3D Color Management menu to make  
adjustments.  
To adjust the settings:  
1.  
2.  
Go to the PICTURE menu and highlight 3D Color Management.  
Press MODE/ENTER on the projector or remote control and the 3D Color  
Management page displays.  
3.  
4.  
Highlight Primary Color and press  
Yellow, Green, Cyan, Blue, or Magenta.  
/
to select a color from among Red,  
Press  
to highlight Hue and press  
/
to select its range. Increase in the range  
will include colors consisted of more proportions of its two adjacent colors.  
Please refer to the illustration to the right  
for how the colors relate to each other.  
For example, if you select Red and set its  
Yellow  
GREEN  
range at 0, only pure red in the projected  
picture will be selected. Increasing its range  
will include red close to yellow and red close  
to magenta.  
RED  
Cyan  
Magenta  
5.  
Press  
to highlight Saturation and adjust  
its values to your preference by pressing  
. Every adjustment made will reflect to  
the image immediately.  
/
BLUE  
For example, if you select Red and set its  
value at 0, only the saturation of pure red will be affected.  
30  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a  
setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be  
overpowering and unrealistic.  
6.  
Press  
to highlight Gain and adjust its values to your preference by pressing  
/
. The contrast level of the primary color you select will be affected. Every  
adjustment made will reflect to the image immediately.  
Repeat steps 3 to 6 for other color adjustments.  
Make sure you have made all of the desired adjustments.  
Press MENU/EXIT to exit and save the settings.  
7.  
8.  
9.  
Setting the presentation timer  
Presentation timer can indicate the presentation time on the screen to help you achieve  
better time management when giving presentations. Follow these steps to utilize this  
function:  
1.  
Go to the SYSTEM SETUP: Basic > Presentation Timer menu and press  
MODE/ENTER to display the Presentation Timer page.  
2.  
Highlight Timer Period and decide the time period by pressing  
/
. The length  
of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes  
in 5-minute increments.  
If the timer is already on, the timer will restart whenever the Timer Period is reset.  
3.  
Press  
to highlight Timer Display and choose if you want the timer to show up  
on the screen by pressing  
/
.
Selection  
Description  
Always  
Displays the timer on screen throughout the presentation time.  
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).  
Never  
Hides the timer throughout the presentation time.  
4.  
5.  
Press  
to highlight Timer Position and set the timer position by pressing  
/
.
Top-Left  
Bottom-Left  
Top-Right  
Bottom-Right  
Press  
to highlight Timer Counting Direction and select your desired counting  
direction by pressing  
/
.
Selection  
Count Up  
Count Down  
Description  
Increases from 0 to the preset time.  
Decreases from the preset time to 0.  
6.  
Press  
reminder by pressing  
to highlight Sound Reminder and decide if you want to activate sound  
. If you select On, a double beep sound will be heard at  
/
the last 30 seconds of counting down/up, and a triple beep sound will be produced  
when the timer is up.  
7.  
8.  
To activate the presentation timer, press  
press MODE/ENTER.  
A confirmation message displays. Highlight Yes and press MODE/ENTER on the  
projector or remote control to confirm. You will see the message “Timer is On”  
displaying on the screen. The timer starts counting when the timer is on.  
and press  
/
to highlight On and  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
   
To cancel the timer, perform the following steps:  
1.  
Go to the SYSTEM SETUP: Basic > Presentation Timer menu and highlight  
Off. Press MODE/ENTER. A confirmation message displays.  
Highlight Yes and press MODE/ENTER to confirm. You will see the message  
Timer is Off” displaying on the screen.  
2.  
Remote paging operations  
Connect the projector to your PC or notebook with a USB cable prior to using the paging  
function. See "Connection" on page 16 for details.  
You can operate your display software program (on a connected PC) which responds to  
page up/down commands (like Microsoft PowerPoint) by pressing PAGE UP/PAGE  
DOWN on the remote control.  
If remote paging function doesn't work, check if the USB connection is correctly made and  
the mouse driver on your computer is updated to the latest version.  
®
®
®
The remote paging function cannot work with Microsoft Windows 98 operating system. Windows XP or  
higher operating systems are recommended.  
Freezing the image  
Press  
Freeze on the remote control to freeze the image. The word “FREEZE” will  
display in the upper left corner of the screen. To release the function, press any key on the  
projector or remote control.  
If your remote control has the following keys, please note that they cannot be pressed to release the function:  
LASER, #1, #4, PAGE UP/PAGE DOWN.  
Even if an image is frozen on the screen, the pictures are running on the video or other  
device. If the connected devices have active audio output, you will still hear the audio even  
though the image is frozen onscreen.  
Hiding the image  
In order to draw the audience's full attention to the presenter, you can use ECO BLANK  
on the projector or remote control to hide the screen image. When this function is  
activated with an audio input connected, the audio can still be heard.  
You can set the blank time in the SYSTEM SETUP: Basic > Operation Settings >  
Blank Timer menu to let the projector return the image automatically after a period of  
time when there is no action taken on the blank screen. The length of time can be set from  
5 to 30 minutes in 5-minute increments.  
If the preset time spans are not suitable for your presentation, select Disable.  
No matter Blank Timer is activated or not, you can press most of the keys on the  
projector or remote control to restore the picture.  
Locking control keys  
With the control keys on the projector locked, you can prevent your projector settings  
from being changed accidentally (by children, for example). When the Panel Key Lock is  
on, no control keys on the projector will operate except  
POWER.  
1. Go to the SYSTEM SETUP: Basic > Panel Key Lock menu, and select On by  
pressing  
displays.  
/
on the projector or remote control. A confirmation message  
32  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
2.  
To release panel key lock, use the remote control to enter the SYSTEM SETUP:  
Basic > Panel Key Lock menu and press to select Off.  
Highlight Yes and press MODE/ENTER to confirm.  
/
Keys on the remote control are still active when panel key lock is enabled.  
If you press  
POWER to turn off the projector without disabling panel key lock, the projector will  
still be in locked status the next time it is turned on.  
Operating in a high altitude environment  
We recommend you use the High Altitude Mode when your environment is between  
1500 m –3000 m above sea level, and ambient temperature is between 0°C–35°C.  
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient temperature is  
between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under such a condition.  
To activate the High Altitude Mode:  
1.  
2.  
3.  
Press MENU/EXIT and then press  
menu is highlighted.  
/
until the SYSTEM SETUP: Advanced  
select On. A  
Press  
to highlight High Altitude Mode and press  
/
confirmation message displays.  
Highlight Yes and press MODE/ENTER.  
Operation under "High Altitude Mode" may cause a higher decibel operating noise level  
because of increased fan speed necessary to improve overall system cooling and  
performance.  
If you use this projector under other extreme conditions excluding the above, it may  
display auto shut-down symptoms, which is designed to protect your projector from over-  
heating. In cases like this, you should switch to High Altitude mode to solve these  
symptoms. However, this is not to state that this projector can operate under any and all  
harsh or extreme conditions.  
Adjusting the sound  
The sound adjustments made as below will have an effect on the projector speaker. Be sure  
you have made a correct connection to the projector audio input. See "Connection" on  
page 16 for how the audio input is connected.  
Muting the sound  
To temporarily turn off the sound:  
1.  
2.  
3.  
Press MENU/EXIT and then press  
menu is highlighted.  
/
until the SYSTEM SETUP: Advanced  
Press  
to highlight Audio Settings and press MODE/ENTER. The Audio  
Settings page displays.  
Highlight Mute and press  
/
to select On.  
Adjusting the sound level  
To adjust the sound level, press VOLUME+/VOLUME- or  
/
, or:  
1.  
2.  
Repeat steps 1-2 above.  
Press to highlight Volume and press  
/
to select a desired sound level.  
Operation  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Turning off the Power On/Off Ring Tone  
To turn off the ring tone:  
1.  
2.  
Repeat steps 1-2 above.  
Press to highlight Power On/Off Ring Tone and press  
/
to select Off.  
The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or  
changing the sound level will not affect the Power On/Off Ring Tone.  
Shutting down the projector  
1.  
Press  
If you don't respond in a few seconds, the message will disappear.  
Press POWER a second time. The POWER indicator light flashes orange,  
POWER and a confirmation message will display prompting you.  
2.  
the projection lamp shuts down, and the fans will continue to run for approximately  
90 seconds to cool down the projector.  
To protect the lamp, the projector will not respond to any commands during the cooling process.  
To shorten the cooling time, you can also activate the Quick cooling function. See "Quick Cooling" on page 41  
for details.  
3.  
Once the cooling process finishes, a "Power Off  
Ring Tone" will be heard. The POWER indicator  
light is a steady orange and fans stop. Disconnect  
the power cord from the power outlet.  
To turn off the power ring tone, see "Turning off the Power On/  
Off Ring Tone" on page 34 for details.  
If the projector is not properly shut down, to protect the lamp,  
when you attempt to re-start the projector, the fans will run for a  
few minutes to cool down. Press  
POWER again to start the  
projector after the fans stop and the POWER indicator light  
turns orange.  
Lamp life results will vary depending on environmental conditions  
and usage.  
Direct power off  
The AC power cord can be pulled out right after the projector is turned off. To protect  
the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to  
re-start the projector, the fans may run for a few minutes to cool down. In such cases,  
press POWER again to start the projector after the fans stop and the POWER  
indicator light turns orange.  
34  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Menu operation  
Menu system  
Please note that the on-screen display (OSD) menus vary according to the signal type  
selected and the projector model you are using.  
Main menu Sub-menu  
Options  
Off/Light Yellow/Pink/Light  
Green/Blue/Blackboard  
Auto/Real/4:3/16:9/16:10  
Wall Color  
Aspect Ratio  
Keystone  
Position  
Phase  
H. Size  
Digital Zoom  
1.  
DISPLAY  
Off/Frame Sequential/Top-  
Bottom  
3D Sync  
3D Sync Invert  
Disable/Invert  
Off/Letter Formation/Worksheet/  
Coordinate Chart  
Off/Letter Formation/Worksheet/  
Coordinate Chart  
Blackboard  
Whiteboard  
Teaching  
Template  
Picture Mode  
Dynamic/Presentation/sRGB/Cinema/User 1/User 2  
Reference Mode Dynamic/Presentation/sRGB/Cinema  
Brightness  
Contrast  
Color  
Tint  
2.  
Sharpness  
Brilliant Color  
Color Temperature  
On/Off  
Cool/Normal/Warm  
Primary Color R/G/B/C/M/Y  
PICTURE  
Hue  
3D Color  
Management  
Saturation  
Gain  
Save Settings  
Quick Auto Search  
On/Off  
3.  
Color Space Conversion  
Auto/RGB/YUV  
SOURCE  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
 
Main menu Sub-menu  
Options  
Timer Period  
Timer Display  
1~240 minutes  
Always/1 min/2 min/3 min/Never  
Top-Left/Bottom-Left/Top-Right/  
Bottom-Right  
Timer Position  
Presentation  
Timer  
Timer Counting  
Direction  
Count Down/Count Up  
Sound Reminder On/Off  
On/Off  
Language  
Front Table/Rear Table/Rear  
4.  
Projector Position  
Menu Display  
Ceiling/Front Ceiling  
5 sec/10 sec/15 sec/20 sec/25 sec/30  
sec  
Center/Top-Left/Top-Right/Bottom-  
Right/Bottom-Left  
SYSTEM  
SETUP:  
Basic  
Time  
Menu Settings Menu Position  
Reminder  
Message  
On/Off  
Direct Power On On/Off  
Signal Power On On/Off  
Disable/5 min/10 min/15 min/20  
min/25 min/30 min  
On/Off  
Disable/5 min/10 min/15 min/20  
min/25 min/30 min  
Disable/30 min/1 hr/2 hr/3 hr/4 hr/  
8 hr/12 hr  
Auto Power Off  
Quick Cooling  
Blank Timer  
Operation  
Settings  
Sleep Timer  
Panel Key Lock  
On/Off  
Background Color  
Splash Screen  
Black/Blue/Purple/BenQ  
Black/Blue/BenQ  
36  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main menu Sub-menu  
Options  
High Altitude Mode  
Mute  
On/Off  
On/Off  
Volume  
Power On/Off  
Ring Tone  
Audio Settings  
On/Off  
Normal/Economic/SMART  
ECO  
Lamp Mode  
Lamp Settings  
Reset Lamp Timer  
Equivalent Lamp Hour  
Change Password  
Security  
Settings  
Power On Lock  
Change Security  
Settings  
Splash Screen Lock  
2400/4800/9600/14400/19200/  
38400/57600/115200  
On/Off  
Baud Rate  
Test Pattern  
5.  
Closed Caption  
Enable  
Caption Version CC1/CC2/CC3/CC4  
SYSTEM  
Closed Caption  
SETUP:  
Advanced  
On/Off  
Network  
On/Off  
Standby  
Settings  
Monitor Out  
Audio Pass  
Through  
On/Off  
Off/Computer 1/Computer 2/  
Video,S-Video/HDMI  
Status  
DHCP  
IP Address  
Wired LAN  
Subnet Mask  
Default Gateway  
DNS Server  
Apply  
Network  
Settings  
AMX Device  
Discovery  
On/Off  
Mac Address  
Reset All Settings  
Source  
Picture Mode  
Resolution  
Color System  
Equivalent Lamp Hour  
Firmware Version  
6.  
Current System Status  
INFORMA  
TION  
Note that the menu items are available when the projector detects at least one valid signal.  
If there is no equipment connected to the projector or no signal detected, limited menu  
items are accessible.  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
Description of each menu  
Function  
Description  
Corrects the projected picture’s color when the projection surface is  
not white. See "Using Wall Color" on page 28 for details.  
There are several options to set the image's aspect ratio depending on  
your input signal source. See "Selecting the aspect ratio" on page 26  
for details.  
Wall Color  
Aspect Ratio  
Keystone  
Corrects any keystoning of the image. See "Correcting keystone" on  
page 20 for details.  
Displays the position adjustment page. To move the projected image,  
use the directional arrow keys. The values shown on the lower  
position of the page change with every key press you made until they  
reach their maximum or minimum.  
Position  
Phase  
This function is only available when a PC signal (analog RGB) is selected.  
Adjusts the clock phase to reduce image  
distortion.  
This function is only available when a PC signal  
(analog RGB) is selected.  
Adjusts the horizontal width of the image.  
H. Size  
This function is only available when a PC signal (analog RGB) is selected.  
Magnifies or reduces the projected image. See "Magnifying and  
searching for details" on page 26 for details.  
Digital Zoom  
This projector features a 3D function which enables you to enjoy the  
3D movies, videos, and sporting events in a more realistic way by  
presenting the depth of the images. You need to wear a pair of 3D  
glasses to view the 3D images.  
Video timing: 480i  
PC timing: up to 1280x800@120Hz for Frame Sequential  
PC timing: up to 1280x800@60Hz for Frame Sequential  
PC timing: up to SXGA+@60Hz for Top-Bottom  
3D Sync  
When the 3D Sync function is on:  
• The brightness level of the projected image will decrease.  
• The Picture Mode cannot be adjusted.  
• The Keystone can only be adjusted within limited degrees.  
3D Sync  
Invert  
When you discover the inversion of the image depth, enable this  
function to correct the problem.  
38  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function  
Description  
Provides several preset patterns for various teaching purposes.  
Teaching  
Template  
Choose Blackboard or Whiteboard first by pressing  
press to choose the pattern you need. Press MODE/ENTER  
to activate the pattern.  
/
and  
/
Pre-defined picture modes are provided so you can optimize your  
projector image set-up to suit your program type. See "Selecting a  
picture mode" on page 28 for details.  
Picture Mode  
Selects a picture mode that best suits your need for the image quality  
and further fine-tune the image based on the selections listed on the  
same page below. See "Setting the User 1/User 2 mode" on page 28  
for details.  
Reference  
Mode  
Adjusts the brightness of the image. See "Adjusting Brightness" on  
page 29 for details.  
Adjusts the degree of difference between dark and light in the image.  
See "Adjusting Contrast" on page 29 for details.  
Brightness  
Contrast  
Adjusts the color saturation level -- the amount of each color in a  
Color  
Tint  
This function is only available when a Video, S-Video or Component Video  
signal is selected.  
Adjusts the red and green color tones of the image. See "Adjusting  
Tint" on page 29 for details.  
This function is only available when a Video or S-Video signal is selected and  
the system format is NTSC.  
Adjusts the image to make it look sharper or softer. See "Adjusting  
Sharpness" on page 29 for details.  
Sharpness  
This function is only available when a Video, S-Video or Component Video  
signal is selected.  
See "Adjusting Brilliant Color" on page 29 for details.  
Brilliant Color  
Color  
Temperature  
See "Selecting a color temperature" on page 29 for details.  
3D Color  
Management  
See "3D Color Management" on page 30 for details.  
Saves the settings made for User 1 or User 2 mode.  
Save Settings  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
Function  
Description  
Quick Auto  
Search  
See "Switching input signal" on page 25 for details.  
Color Space  
Conversion  
See "Changing Color Space" on page 25 for details.  
Presentation  
Timer  
Reminds the presenter to finish the presentation within a certain time  
frame. See "Setting the presentation timer" on page 31 for details.  
Sets the language for the On-Screen Display (OSD) menus. See "Using  
the menus" on page 21 for details.  
Language  
Projector  
Position  
The projector can be installed on a ceiling or behind a screen, or with  
one or more mirrors. See "Choosing a location" on page 13 for details.  
Menu Display Time  
Sets the length of time the OSD will remain active after your last key  
press. The range is from 5 to 30 seconds in 5-second increments.  
Menu  
Menu Position  
Settings  
Sets the On-Screen Display (OSD) menu position.  
Reminder Message  
Sets the reminder messages on or off.  
40  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function  
Description  
Direct Power On  
Allows the projector to turn on automatically once the power is fed  
through the power cord.  
Signal Power On  
Sets whether to turn the projector directly on without pressing the  
POWER key on the projector when the projector is in standby  
mode and the signal is feed through the VGA cable.  
Auto Power Off  
Allows the projector to turn off automatically if no input signal is  
detected after a set period of time. See "Setting Auto Power Off" on  
page 46 for details.  
Operation  
Settings  
Quick Cooling  
Enables or disables the Quick Cooling function. Selecting On enables  
the function and projector cooling time will be shortened from a  
normal 90-second duration to approximately 30 seconds.  
Blank Timer  
Sets the image blank time when the Blank feature is activated, once  
elapsed the image will return to the screen. See "Hiding the image" on  
page 32 for details.  
Sleep Timer  
Sets the auto-shutdown timer.  
Disables or enables all panel key functions except  
projector and keys on the remote control. See "Locking control keys"  
on page 32 for details.  
POWER on the  
Panel Key  
Lock  
Background  
Color  
Sets the background color for the projector.  
Splash  
Screen  
Allows you to select which logo screen will display during projector  
start-up.  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
41  
 
Function  
Description  
High  
Altitude  
Mode  
A mode for operation in high altitude areas. See "Operating in a high  
altitude environment" on page 33 for details.  
Mute  
Audio  
Volume  
Settings  
Power On/Off Ring Tone  
See "Adjusting the sound" on page 33 for details.  
Lamp Mode  
See "Setting Lamp Mode as Economic" on page 46 for details.  
Reset Lamp Timer  
See "Resetting the lamp timer" on page 50 for details.  
Lamp  
Settings  
Equivalent Lamp Hour  
See "Getting to know the lamp hour" on page 46 for details on how the  
total lamp hour is calculated.  
Change Password  
You will be asked to enter the current password before changing to a  
new one. See "Utilizing the password function" on page 22 for details.  
Security  
Settings  
Change Security Settings  
Power On Lock  
Splash Screen Lock  
See "Utilizing the password function" on page 22 for details.  
Selects a baud rate that is identical with your computer’s so that you  
can connect the projector using a suitable RS-232 cable and update or  
download the projector’s firmware. This function is intended for  
qualified service personnel.  
Baud Rate  
Selecting On enables the function and the projector displays the grid  
test pattern. It helps you adjust the image size and focus and check that  
the projected image is free from distortion.  
Test Pattern  
Closed Caption Enable  
Activates the function by selecting On when the selected input signal  
carries closed captions.  
Captions: An on-screen display of the dialogue, narration, and  
sound effects of TV programs and videos that are closed captioned  
(usually marked as "CC" in TV listings).  
Closed  
Caption  
Caption Version  
Selects a preferred closed captioning mode. To view captions, select  
CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary  
language in your area).  
42  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function  
Description  
Network  
Selecting On enables the function. The projector is able to provide the  
network function when it is in standby mode.  
Monitor Out  
Selecting On enables the function. The projector can output a VGA  
signal when it is in standby mode and the COMPUTER 1 jack is  
correctly connected to devices. See "Connection" on page 16 for how  
to make the connection.  
Audio Pass Through  
The projector can play sound when it is in standby mode and the  
corresponding jacks are correctly connected to devices. Press  
Standby  
Settings  
/
to  
choose the source that you wish to use. When you select Computer  
1 or Computer 2, audio signal can only be fed into the AUDIO-IN 1  
or AUDIO-IN 2 jack. When you select Video,S-Video, audio signal  
can only be fed into the AUDIO-IN L/R jacks. There is no need to  
connect the audio cable when HDMI is selected since the HDMI cable  
carries audio signal.  
See "Connection" on page 16 for how to make the connection.  
Enabling this function slightly increases the standby power consumption.  
Wired LAN  
See BenQ Network Projector Operation Guide for details.  
AMX Device Discovery  
Selecting On enables the function. When AMX Device Discovery is  
On, the projector can be detected by AMX controller.  
Network  
Settings  
Mac Address  
Displays the mac adress of this projector.  
Returns all settings to the factory preset values.  
Reset All  
Settings  
The following settings will still remain: Phase, H. Size, User 1, User 2,  
Color Space Conversion, Projector Position, High Altitude Mode,  
Security Settings, Network Settings and Baud Rate.  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
 
Function  
Description  
Source  
Shows the current signal source.  
Picture Mode  
Shows the selected mode in the PICTURE menu.  
Resolution  
Shows the native resolution of the input signal.  
Current  
System  
Status  
Color System  
Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.  
Equivalent Lamp Hour  
Displays the number of hours the lamp has been used.  
Firmware Version  
Shows the firmware version of your projector.  
44  
Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
Care of the projector  
Your projector needs little maintenance. The only thing you need to do on a regular basis  
is to keep the lens and case clean.  
Never remove any parts of the projector except the lamp. Contact your dealer if other  
parts need replacing.  
Cleaning the lens  
Clean the lens whenever you notice dirt or dust on the surface. Please be sure to turn off  
the projector and let it cool down completely before cleaning the lens.  
Use a canister of compressed air to remove dust.  
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens  
cleaner and gently wipe the lens surface.  
Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile  
solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or  
maintaining prolonged contact with rubber or vinyl materials may result in damage to  
the projector surface and cabinet material.  
Cleaning the projector case  
Before you clean the case, turn the projector off using the proper shutdown procedure as  
described in "Shutting down the projector" on page 34 and unplug the power cord.  
To remove dirt or dust, wipe the case with a soft, lint-free cloth.  
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH  
detergent. Then wipe the case.  
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.  
Storing the projector  
If you need to store the projector for an extended time, please follow the instructions  
below:  
Make sure the temperature and humidity of the storage area are within the  
recommended range for the projector. Please refer to "Specifications" on page 53 or  
consult your dealer about the range.  
Retract the adjuster feet.  
Remove the battery from the remote control.  
Pack the projector in its original packing or equivalent.  
Transporting the projector  
It is recommended that you ship the projector with its original packing or equivalent.  
When you carry the projector yourself, please use the original box or the soft carry case.  
Maintenance  
Download from Www.Somanuals.com. All Manuals Search And Download.  
45  
   
Lamp information  
Getting to know the lamp hour  
When the projector is in operation, the duration (in hours) of lamp usage is automatically  
calculated by the built-in timer.  
See "Setting Lamp Mode as Economic" below for more information on Economic mode.  
To obtain the lamp hour information:  
1.  
Press MENU/EXIT and then press  
Advanced menu.  
/
to highlight the SYSTEM SETUP:  
2.  
Press to highlight Lamp Settings and press MODE/ENTER. The Lamp  
Settings page displays.  
3.  
4.  
You will see the Equivalent Lamp Hour information displaying on the menu.  
To leave the menu, press MENU/EXIT.  
You can also get the lamp hour information on the INFORMATION menu.  
Extending lamp life  
The projection lamp is a consumable item that normally can last up to 3000-4000 hours  
with proper usage. To keep the lamp life as long as possible, you can do the following  
settings via the OSD menu.  
Setting Lamp Mode as Economic  
Using Economic mode reduces system noise and power consumption by 20%. If the  
Economic mode is selected, the light output will be reduced and result in darker  
projected pictures.  
Setting the projector in Economic mode also extends the lamp operation life. To set  
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings >  
Lamp Mode menu and press  
/
.
Setting Auto Power Off  
This function allows the projector to turn off automatically if no input signal is detected  
after a set period of time to prevent unnecessary waste of lamp life.  
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Operation Settings  
> Auto Power Off menu and press  
/
. The time period can be set from 5 to 30  
minutes in 5-minute increments. If the preset time lengths are not suitable for your  
presentation, select Disable. The projector will not automatically shut down in a certain  
time period.  
46  
Maintenance  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Timing of replacing the lamp  
When the Lamp indicator lights up red or a message appears suggesting it is time to  
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a  
malfunction in the projector and in some instances the lamp may explode.  
Go to http://lamp.benq.com for a replacement lamp.  
The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot.  
Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after  
turning the power back on, please contact your dealer. See "Indicators" on page 51 for details.  
The following Lamp warning displays will remind you to change the lamp.  
Status  
Message  
Install a new lamp for optimal performance. If the  
projector is normally run with Economic  
selected (See "Getting to know the lamp hour" on  
page 46), you may continue to operate the  
projector until the next hour lamp warning  
appears.  
Notice  
Order Replacement Lamp  
Lamp>XXXX Hours  
Order a new lamp at lamp.benq.com  
Press MODE/ENTER to dismiss the message.  
OK  
It is strongly recommended that you replace the  
lamp at this age. The lamp is a consumable item.  
The lamp brightness diminishes with use. This is  
normal lamp behavior. You can replace the lamp  
whenever you notice that the brightness level has  
significantly diminished.  
Notice  
Replace Lamp Soon  
Lamp>XXXX Hours  
Order a new lamp at lamp.benq.com  
Press MODE/ENTER to dismiss the message.  
OK  
Notice  
Replace Lamp Now  
Lamp>XXXX Hours  
Order a new lamp at lamp.benq.com  
OK  
The lamp MUST be replaced before the projector  
will operate normally.  
WARNING  
Out of Lamp Usage Time  
Press MODE/ENTER to dismiss the message.  
Replace lamp (refer to User Manual)  
Then reset lamp timer  
Order a new lamp at lamp.benq.com  
OK  
"XXXX" shown in the above messages are numbers that vary depending on different models.  
Maintenance  
Download from Www.Somanuals.com. All Manuals Search And Download.  
47  
Replacing the lamp  
To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before  
changing the lamp.  
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the  
lamp.  
To reduce the risk of injuries to fingers and damage to internal components, use caution when removing  
lamp glass that has shattered into sharp pieces.  
To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not  
touch the empty lamp compartment when the lamp is removed.  
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a  
proper manner.  
To assure optimal performance from the projector, it is recommended that you purchase a qualified  
projector lamp for lamp replacement.  
If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make  
sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes  
caused by fractured lamp.  
1.  
Turn the power off and disconnect the projector from the power outlet. If the lamp  
is hot, avoid burns by waiting for approximately 45 minutes until the lamp has  
cooled.  
2.  
Loosen the screw that secures the lamp  
cover on the side of the projector until  
the lamp cover loosens.  
3.  
Remove the lamp cover from the  
projector.  
1
4.  
Remove the protection film.  
Do not turn the power on with the lamp cover  
removed.  
1
2
Do not insert your fingers between the lamp and the  
projector. The sharp edges inside the projector may  
cause injuries.  
5.  
Disconnect the lamp connector from the  
projector.  
6.  
7.  
Loosen the screw that secures the lamp.  
Lift the handle so that it stands up.  
2
1
3
48  
Maintenance  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8.  
Use the handle to slowly pull the lamp out of  
the projector.  
Pulling it too quickly may cause the lamp to break and  
scatter broken glass in the projector.  
Do not place the lamp in locations where water might  
splash on it, children can reach it, or near flammable  
materials.  
Do not insert your hands into the projector after the  
lamp is removed. If you touch the optical components  
inside, it could cause color unevenness and distortion of  
the projected images.  
9.  
As shown in the figure, lower the new lamp.  
10. Reconnect the lamp connector to the  
projector.  
11. Tighten the screw that secures the lamp.  
12. Ensure the handle is fully laid flat and locked  
in place.  
2
3
Loose screw may cause a bad connection, which could  
result in malfunction.  
1
Do not over tighten the screw.  
13. Replace the lamp cover on the projector.  
14. Tighten the screw that secures the lamp  
cover.  
Loose screw may cause a bad connection, which could  
result in malfunction.  
Do not over tighten the screw.  
15. Connect the power and restart the projector.  
Do not turn the power on with the lamp cover removed.  
Maintenance  
Download from Www.Somanuals.com. All Manuals Search And Download.  
49  
Resetting the lamp timer  
16. After the startup logo, open the On-Screen Display (OSD) menu. Go to the  
SYSTEM SETUP: Advanced > Lamp Settings menu. Press MODE/ENTER.  
The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning  
message is displayed asking if you want to reset the lamp timer. Highlight Reset and  
press MODE/ENTER. The lamp time will be reset to “0”.  
Do not reset if the lamp is not new or replaced as this could cause damage.  
50  
Maintenance  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Indicators  
Light  
Status & Description  
Power events  
Off  
Off  
Off  
Off  
Orange Stand-by mode.  
Green  
Flashing  
Off  
Off  
Powering up.  
Green Normal operation.  
The projector needs 90 seconds to cool down as it was  
abnormally shut down without the normal cooling down  
process.  
The projector needs to cool for 90 seconds after the  
power is turned off.  
The projector has shut down automatically. If you try to  
re-start the projector, it will shut down again. Please  
contact your dealer for assistance.  
Orange  
Flashing  
Off  
Off  
Lamp events  
The projector has shut down automatically. If you try to re-  
start the projector, it will shut down again. Please contact  
your dealer for assistance.  
Orange  
Flashing  
Red  
Red  
Off  
1.  
2.  
The projector needs 90 seconds to cool down. Or  
Please contact your dealer for assistance.  
Off  
Off  
Thermal events  
Off  
Red  
Red  
Red  
Off  
Off  
Green  
Orange  
Red  
Green  
Orange  
Red  
Green  
Orange  
Red  
Green  
Orange  
Red  
Red  
Red  
Red  
Red  
Red  
Red  
Red  
Red  
Red  
Red  
Red  
Green  
Green  
Off  
Off  
Red  
Red  
Red  
The projector has shut down automatically. If you try to re-  
Green start the projector, it will shut down again. Please contact  
your dealer for assistance.  
Green  
Green  
Orange  
Orange  
Orange  
Off  
Green  
Off  
Maintenance  
Download from Www.Somanuals.com. All Manuals Search And Download.  
51  
 
Troubleshooting  
The projector does not turn on.  
Cause  
Remedy  
Plug the power cord into the AC power jack on  
the projector, and plug the power cord into the  
power outlet. If the power outlet has a switch,  
make sure that it is switched on.  
There is no power from the power cord.  
Attempting to turn the projector on again Wait until the cooling down process has  
during the cooling process.  
completed.  
No picture  
Cause  
Remedy  
The video source is not turned on or  
connected correctly.  
Turn the video source on and check that the signal  
cable is connected correctly.  
The projector is not correctly connected  
to the input signal device.  
Check the connection.  
The input signal has not been correctly  
selected.  
The lens cover is still closed.  
Select the correct input signal with the SOURCE  
key on the projector or remote control.  
Open the lens cover.  
Blurred image  
Cause  
Remedy  
The projection lens is not correctly  
focused.  
Adjust the focus of the lens using the focus ring.  
The projector and the screen are not  
aligned properly.  
The lens cover is still closed.  
Adjust the projection angle and direction as well  
as the height of the projector if necessary.  
Open the lens cover.  
Remote control does not work  
Cause  
Remedy  
The battery is out of power.  
Replace the battery with a new one.  
There is an obstacle between the remote  
control and the projector.  
Remove the obstacle.  
You are too far away from the projector. Stand within 8 meters (26 feet) of the projector.  
The password is incorrect  
Cause  
Remedy  
Please see "Entering the password recall  
procedure" on page 23 for details.  
You do not remember the password.  
52  
Troubleshooting  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Specifications  
Projector specifications  
All specifications are subject to change without notice.  
Optical  
Control  
Resolution  
(MX815ST/MX815ST+/MX816ST)  
1024 x 768 XGA  
RS-232 serial control  
9 pin x 1  
IR receiver x 2  
(MW817ST)  
USB port (Mini-B x 1)  
1280 x 800 WXGA  
Display system  
1-CHIP DMD  
Input terminals  
Computer input  
RGB input  
Lens F/Number  
F = 2.6  
Lamp  
D-Sub 15-pin (female) x 2  
210 W lamp  
Video signal input  
S-VIDEO  
Mini DIN 4-pin port x 1  
VIDEO  
RCA jack x 1  
Electrical  
Power supply  
AC100–240V, 3.2 A, 50-60 Hz  
(Automatic)  
Power consumption  
295 W (Max); < 1 W (Standby)  
SD/HDTV signal input  
Analog - Component RCA jack x 3  
(through RGB input)  
Digital - HDMI V1.3 x 1  
Audio signal input  
Audio in  
Mechanical  
Weight  
PC audio jack x 2  
RCA audio jack (L/R) x 2  
2.8 Kg (6.17 lbs)  
Output terminals  
Environmental Requirements  
RGB output  
D-Sub 15-pin (female) x 1  
Speaker  
(Stereo) 10 watt x 1  
Audio signal output  
PC audio jack x 1  
Operating temperature  
0°C–40°C at sea level  
Operating relative humidity  
10%–90% (without condensation)  
Operating altitude  
0–1499 m at 0°C–35°C  
1500–3000 m at 0°C–30°C (with  
High Altitude Mode on)  
Specifications  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Dimensions  
287.3 mm (W) x 114.4 mm (H) x 232.6 mm (D)  
287.3  
232.6  
114.4  
62  
62  
Ceiling mount installation  
207.6  
Ceiling Mount screw: M4  
x 8 (Max L = 8 mm)  
199.6  
Unit: mm  
78  
83.38  
141.88  
287.3  
123.0  
232.6  
54  
Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Wall mount installation  
Minimum installation requirements  
Computer  
Resolution:  
XGA  
SMART  
Board  
660  
Smart  
Board  
680  
Promethean  
ActivBoard  
164  
Promethean  
ActivBoard  
178  
RM  
ClassBoard2  
77.5  
Hitachi  
StarBoard  
FX-63  
Diagram  
Reference  
StarBoard  
FX-77  
Image  
Resolution:  
XGA  
Image  
Diagonal  
(inches)  
D
H
64  
77  
64  
78  
78  
63  
77  
Image  
Height  
(mm)  
975  
1173  
1565  
975  
1189  
1585  
1181  
1575  
960  
1173  
1565  
Image  
Width  
(mm)  
W
1300  
1300  
1280  
Distance  
from floor  
to bottom  
of image  
(mm)  
f
900  
790  
900  
950  
900  
790  
900  
970  
900  
970  
900  
780  
900  
950  
Distance  
from  
screen  
surface to  
projector  
rear case  
(mm)  
a
Distance  
from top  
case to the  
top of  
b
94  
124  
94  
126  
126  
92  
124  
image  
(mm)  
Distance  
from top of  
wallmount  
to ceiling  
(mm)  
c
e
50  
50  
50  
50  
50  
50  
50  
Minimum  
Ceiling  
Height  
(mm)  
2347  
2575  
2347  
2593  
2585  
2330  
2575  
Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
55  
 
Computer Resolution:  
WXGA  
Image Resolution: WXGA  
SMART  
Board  
685  
Promethean  
ActivBoard  
387  
Hitachi  
FX-TRIO-  
88W  
Hitachi  
FX-DUO-  
88W  
Diagram  
Reference  
Image Diagonal (inches)  
Image Height (mm)  
Image Width (mm)  
D
H
87  
87  
88  
88  
1171  
1874  
1171  
1874  
1181  
1887  
1181  
1887  
W
Distance from floor to  
bottom of image (mm)  
f
900  
916  
900  
916  
900  
926  
900  
926  
Distance from screen surface  
to projector lens (mm)  
a
b
c
e
Distance from top case to  
the top of image (mm)  
6.8  
6.8  
7.5  
7.5  
Distance from top of wall  
mount to ceiling (mm)  
50  
50  
50  
50  
Minimum Ceiling Height  
(mm)  
2461.8  
2461.8  
2472.5  
2472.5  
56  
Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Minimum Ceiling Height (mm) = f + H + b + 60 + 274+ c  
Ceiling  
c
60  
e
274  
a
b
232.6  
D
Projection  
area  
H
Wall plate  
W
Distance from floor to  
bottom of image  
f
floor  
The dimensions are based on the BenQ wall mount (P/N: 5J.J4R10.001).  
All measurements are approximate and may vary from the actual sizes. BenQ recommends that if you  
intend to permanently install the projector, you should physically test the projection size and distance  
using the actual projector in situ before you permanently install it, so as to make allowance for this  
projector's optical characteristics. This will help you determine the exact mounting position so that it best  
suits your installation location.  
The dimensions supplied are offered as a guide only and may differ depending on several factors relating to  
any specific installation.  
The dimensions are based on the projector being configured with zero keystone correction.  
The dimensions assume that the wall mount arm is positioned 90° from the bottom case of projector and  
screen surface.  
Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
57  
Timing chart  
Supported timing for PC input  
Vertical  
Frequency  
(Hz)  
59.940  
72.809  
75.000  
85.008  
70.087  
56.25  
Horizontal  
Frequency  
(kHz)  
31.469  
37.861  
37.500  
43.269  
31.469  
35.156  
Pixel  
Frequency  
(MHz)  
25.175  
31.500  
31.500  
36.000  
28.3221  
36  
Resolution  
Mode  
VGA_60  
VGA_72  
VGA_75  
VGA_85  
720 x 400_70  
SVGA_56  
640 x 480  
720 x 400  
SVGA_60*  
SVGA_72  
SVGA_75  
60.317  
72.188  
75.000  
85.061  
37.879  
48.077  
46.875  
53.674  
40.000  
50.000  
49.500  
56.250  
800 x 600  
SVGA_85  
SVGA_120**  
(Reduce Blanking)  
XGA_60*  
119.854  
77.425  
83.000  
60.004  
70.069  
75.029  
84.997  
48.363  
56.476  
60.023  
68.667  
65.000  
75.000  
78.750  
94.500  
XGA_70  
XGA_75  
XGA_85  
1024 x 768  
XGA_120**(Reduce  
Blanking)  
1152 x 864_75  
BenQ Notebook  
Timing  
119.989  
75  
97.551  
67.5  
115.5  
108  
1152 x 864  
1024 x 576  
60.0  
35.820  
46.966  
BenQ Notebook  
Timing  
1024 x 600  
64.995  
41.467  
51.419  
1280 x 720  
1280 x 768  
1280 x 720_60*  
1280 x 768_60*  
WXGA_60*  
WXGA_75  
60  
45.000  
47.776  
49.702  
62.795  
71.554  
74.250  
79.5  
83.500  
106.500  
122.500  
59.87  
59.810  
74.934  
84.880  
1280 x 800  
WXGA_85  
WXGA_120**  
(Reduce Blanking)  
SXGA_60***  
SXGA_75  
119.909  
101.563  
146.25  
60.020  
75.025  
85.024  
60.000  
85.002  
60.015  
59.887  
59.978  
60.000  
59.954  
66.667  
74.546  
75.020  
75.06  
63.981  
79.976  
91.146  
60.000  
85.938  
47.712  
55.935  
65.317  
75.000  
65.29  
108.000  
135.000  
157.500  
108  
1280 x 1024  
1280 x 960  
SXGA_85  
1280 x 960_60***  
1280 x 960_85  
1360 x 768_60***  
WXGA+_60***  
SXGA+_60***  
UXGA  
148.500  
85.500  
106.500  
121.750  
162.000  
146.25  
30.240  
57.280  
80.000  
100.00  
1360 x 768  
1440 x 900  
1400 x 1050  
1600 x 1200  
1680 x 1050  
1680x1050_60  
MAC13  
640 x 480@67Hz  
832 x 624@75Hz  
1024 x 768@75Hz  
1152 x 870@75Hz  
35.000  
49.722  
60.241  
68.68  
MAC16  
MAC19  
MAC21  
*Supported timing for non-3D and 3D signal with Frame Sequential and Top-Bottom format.  
**Supported timing for non-3D and 3D signal with Frame Sequential format.  
***Supported timing for non-3D and 3D signal with Top-Bottom format.  
58  
Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The timings showing above may not be supported due to EDID file and VGA graphic card limitations. It is  
possible that some timings cannot be chosen.  
Supported timing for HDMI (HDCP) input  
Vertical  
Horizontal  
Frequency  
(kHz)  
31.469  
37.861  
37.500  
43.269  
31.469  
37.879  
Pixel  
Frequency  
(MHz)  
25.175  
31.500  
31.500  
36.000  
28.3221  
40.000  
50.000  
49.500  
56.250  
Resolution  
Mode  
Frequency  
(Hz)  
VGA_60  
VGA_72  
VGA_75  
59.940  
72.809  
75.000  
85.008  
70.087  
60.317  
72.188  
75.000  
85.061  
640 x 480  
720 x 400  
VGA_85  
720 x 400_70  
SVGA_60*  
SVGA_72  
SVGA_75  
SVGA_85  
48.077  
46.875  
53.674  
800 x 600  
SVGA_120**  
(Reduce Blanking)  
XGA_60*  
119.854  
77.425  
83.000  
60.004  
70.069  
75.029  
84.997  
48.363  
56.476  
60.023  
68.667  
65.000  
75.000  
78.750  
94.500  
XGA_70  
XGA_75  
XGA_85  
1024 x 768  
XGA_120**  
(Reduce Blanking)  
1152 x 864_75  
BenQ Notebook  
Timing  
119.989  
75  
97.551  
67.5  
115.5  
108  
1152 x 864  
1024 x 576@60Hz  
60.00  
35.820  
46.996  
BenQ Notebook  
Timing  
1024 x 600@65Hz  
64.995  
41.467  
51.419  
1280 x 720  
1280 x 768  
1280 x 720_60*  
1280 x 768_60*  
WXGA_60*  
WXGA_75  
60  
59.87  
59.810  
74.934  
84.880  
45.000  
47.776  
49.702  
62.795  
71.554  
74.250  
79.5  
83.500  
106.500  
122.500  
1280 x 800  
WXGA_85  
WXGA_120**  
(Reduce Blanking)  
SXGA_60***  
SXGA_75  
119.909  
101.563  
146.25  
60.020  
75.025  
85.024  
60.000  
85.002  
60.015  
59.887  
59.978  
60.000  
59.954  
66.667  
74.546  
75.020  
75.06  
63.981  
79.976  
91.146  
60.000  
85.938  
47.712  
55.935  
65.317  
75.000  
65.290  
35.000  
49.722  
60.241  
68.68  
108.000  
135.000  
157.500  
108  
1280 x 1024  
1280 x 960  
SXGA_85  
1280 x 960_60***  
1280 x 960_85  
1360 x 768_60***  
WXGA+_60***  
SXGA+_60***  
UXGA  
148.500  
85.500  
106.500  
121.750  
162.000  
146.250  
30.240  
57.280  
80.000  
100.00  
1360 x 768  
1440 x 900  
1400 x 1050  
1600 x 1200  
1680 x 1050  
1680x1050_60  
MAC13  
640 x 480@67Hz  
832 x 624@75Hz  
1024 x 768@75Hz  
1152 x 870@75Hz  
MAC16  
MAC19  
MAC21  
*Supported timing for non-3D and 3D signal with Frame Sequential and Top-Bottom format.  
**Supported timing for non-3D and 3D signal with Frame Sequential format.  
***Supported timing for non-3D and 3D signal with Top-Bottom format.  
Specifications  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The timings showing above may not be supported due to EDID file and VGA graphic card limitations. It is  
possible that some timings cannot be chosen.  
Vertical  
Horizontal  
Pixel  
Timing  
Resolution  
Frequency  
Frequency Frequency  
Remark  
(Hz)  
59.94  
59.94  
50  
50  
50  
60  
50  
60  
24  
(kHz)  
15.73  
31.47  
15.63  
31.25  
37.5  
45.00  
28.13  
33.75  
27  
(MHz)  
27  
27  
27  
27  
74.25  
74.25  
74.25  
74.25  
74.25  
74.25  
74.25  
148.5  
148.5  
480i**  
480p  
576i  
720 x 480  
720 x 480  
720 x 576  
HDMI only  
HDMI only  
HDMI/DVI  
HDMI/DVI  
HDMI/DVI  
HDMI/DVI  
HDMI/DVI  
HDMI/DVI  
HDMI/DVI  
HDMI/DVI  
HDMI/DVI  
HDMI/DVI  
HDMI/DVI  
576p  
720 x 576  
720/50p  
720/60p  
1080/50i  
1080/60i  
1080/24P  
1080/25P  
1080/30P  
1080/50P  
1080/60P  
1280 x 720  
1280 x 720  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
25  
30  
50  
60  
28.13  
33.75  
56.25  
67.5  
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.  
**Supported timing for non-3D and 3D signal with Frame Sequential format.  
Supported timing for Component-YPbPr input  
Vertical  
Horizontal  
Pixel Frequency  
(MHz)  
13.5  
Timing  
Resolution  
Frequency (Hz) Frequency (kHz)  
480i**  
480p  
576i  
720 x 480  
720 x 480  
720 x 576  
59.94  
59.94  
50  
50  
50  
60  
50  
60  
24  
25  
30  
50  
60  
15.73  
31.47  
15.63  
31.25  
37.5  
45.00  
28.13  
33.75  
27  
28.13  
33.75  
56.25  
67.5  
27  
13.5  
27  
576p  
720 x 576  
720/50p  
720/60p  
1080/50i  
1080/60i  
1080/24P  
1080/25P  
1080/30P  
1080/50P  
1080/60P  
1280 x 720  
1280 x 720  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
74.25  
74.25  
74.25  
74.25  
74.25  
74.25  
74.25  
148.5  
148.5  
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.  
**Supported timing for non-3D and 3D signal with Frame Sequential format.  
Supported timing for Video and S-Video inputs  
Horizontal  
Frequency (kHz)  
15.73  
Vertical Frequency Color sub-carrier  
Video mode  
(Hz)  
60  
Frequency (MHz)  
NTSC**  
PAL  
3.58  
15.63  
50  
4.43  
SECAM  
PAL-M  
15.63  
15.73  
50  
60  
4.25 or 4.41  
3.58  
PAL-N  
15.63  
50  
3.58  
PAL-60  
NTSC4.43  
15.73  
15.73  
60  
60  
4.43  
4.43  
**Supported timing for non-3D and 3D signal with Frame Sequential format.  
60  
Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warranty and Copyright information  
Limited warranty  
BenQ warrants this product against any defects in material and workmanship, under  
normal usage and storage.  
Proof of purchase date will be required with any warranty claim. In the event this product  
is found to be defective within the warranty period, BenQ's only obligation and your  
exclusive remedy shall be replacement of any defective parts (labor included). To obtain  
warranty service, immediately notify the dealer from which you purchased the product of  
any defects.  
Important: The above warranty shall be void if the customer fails to operate the product in  
accordance with BenQ's written instructions, especially the ambient humidity must be in-  
between 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920  
feet, and avoiding to operate the projector in a dusty environment. This warranty gives you  
specific legal rights, and you may have other rights which vary from country to country.  
Copyright  
Copyright 2012 by BenQ Corporation. All rights reserved. No part of this publication may  
be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any  
language or computer language, in any form or by any means, electronic, mechanical,  
magnetic, optical, chemical, manual or otherwise, without the prior written permission of  
BenQ Corporation.  
Disclaimer  
BenQ Corporation makes no representations or warranties, either expressed or implied,  
with respect to the contents hereof and specifically disclaims any warranties,  
merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves  
the right to revise this publication and to make changes from time to time in the contents  
hereof without obligation to notify any person of such revision or changes.  
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others  
are copyrights of their respective companies or organizations.  
Patents  
This BenQ projector is covered by the following patents:  
U.S. patents 6,837,608; 7,275,834; 7,181,318. TW patents 202690; 205470; I228635;  
I259932.  
China patents ( 中国发明专利 ) ZL01143168.7; ZL03119907.0; ZL200510051609.2  
Warranty and Copyright information  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

BenQ Projector W770ST User Manual
Blackberry Cell Phone PRD 12528 103 User Manual
BMW Automobile BMW 735i 732iL 750E32 User Manual
Bolens Lawn Mower 190 088 000 User Manual
Bosch Appliances Oven HBN 43M 550 A User Manual
Briggs Stratton Pressure Washer 20209 User Manual
Broan Blower EB15 User Manual
Casio Clock DQ 542 User Manual
Cecilware Blender B15FM 120 User Manual
Chevrolet Automobile 19 User Manual