W500 LCD Projector
Home Entertainment Series
User Manual
Welcome
Download from Www.Somanuals.com. All Manuals Search And Download.
Speeding up the process of source search ..................................................................26
Fine-tuning the image size and clarity .......................................................................26
Correcting two-dimensional keystone .......................................................................26
Optimizing the image ................................................................................28
1. Selecting a picture mode .........................................................................................28
Setting black level ........................................................................................................30
Selecting a color temperature .....................................................................................31
Setting a preferred color temperature ........................................................................31
Turning the power off ...............................................................................34
Using the menus ........................................................................................36
Picture--Basic menu ..................................................................................37
Display menu .............................................................................................38
System Setup menu ...................................................................................39
Advanced Setup menu ...............................................................................40
Information menu .....................................................................................41
Maintenance ....................................................................................................... 42
Care of the projector .................................................................................42
Cleaning the lens .........................................................................................................42
Storing the projector ...................................................................................................42
Transporting the projector .........................................................................................42
Cleaning and replacing the dust filter ........................................................................42
Lamp Information .....................................................................................44
Table of contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting ..................................................................................................49
Specifications .......................................................................................................50
Optical ......................................................................................................................... 50
Electrical ...................................................................................................................... 50
Warranty and Copyright information ...............................................................53
Regulation statements .........................................................................................54
MIC statement ...........................................................................................54
WEEE directive ..........................................................................................54
4
Table of contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety instructions
Your BenQ projector is designed and tested to meet the latest standards for safety of information technology
equipment. However, to ensure safe use of this product, it is important that you follow the instructions
mentioned in this manual and marked on the product.
Safety instructions
1. Please read this user manual before you operate your 4. Do not place the projector in any of the
projector. Keep this manual in a safe place for future
reference.
following environments:
- space that is poorly ventilated or confined.
Allow at least 50 cm clearance from walls
and free flow of air around the projector;
- locations where temperatures may become
excessively high, such as the inside of a car
with all windows closed;
- locations where excessive humidity, dust, or
cigarette smoke may contaminate optical
components, shortening the projector’s
lifespan and darkening the screen;
2. Always place the projector on a level, horizontal
surface during operation.
- Do not place the projector on an unstable cart, stand,
or table as it may fall and be damaged;
- Do not place inflammables near the projector;
- locations near fire alarms;
- Do not use if tilted at an angle of more than 10 degrees
left to right, nor at angle of more than 15 degrees front
to back.
- locations with an ambient temperature
above 40°C / 104°F;
- locations where altitude is higher than 3050
metres / 10000 feet above sea level.
3. When you think service or repair is required, take the
projector only to a suitably qualified technician.
10000
feet
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Safety instructions (continued)
5. Do not block the ventilation holes whilst the
9. Do not look straight into the projector lens during
projector is on (even in standby mode):
- Do not cover the projector with any item;
operation. It may harm your sight.
- Do not place the projector on a blanket, bedding
or any other soft surface.
10. Do not operate the projector lamp beyond the
rated lamp life. Excessive operation of lamps
beyond the rated life could cause a lamp to break
on rare occasions.
6. In areas where the mains power supply voltage
may fluctuate by 10 volts, it is recommended
that you connect your projector through a power
stabilizer, surge protector or uninterruptible
power supply (UPS) as appropriate to your
situation.
11. The lamp becomes extremely hot during
operation. Allow the projector to cool for
approximately 45 minutes prior to removing the
lamp assembly for replacement.
7. Do not step on the projector or place any objects
upon it.
8. Do not place liquids near or on the projector.
Liquids spilled into the projector will void your
warranty. If the projector does become wet,
disconnect it from the power point and call BenQ
to have the projector repaired.
6
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions (continued)
12. Never attempt to replace the lamp assembly until 15. This projector is capable of displaying inverted
the projector has cooled down and is unplugged
from the power supply.
images for ceiling mount installation. Use only
BenQ’s Ceiling Mounting Kit for mounting.
13. Do not attempt to disassemble this projector.
There are dangerous high voltages inside which
may cause death if you should come into contact
with live parts. The only user serviceable parts are
the lamp and air filters which have their own
Under no circumstances should you ever undo or
remove any other covers. Refer servicing only to
suitably qualified professional service personnel.
Ceiling mounting the projector
We want you to have a pleasant experience using
your BenQ projector, so we need to bring this
safety matter to your attention to prevent possible
damage to person and property.
If you intend to mount your projector on the
ceiling, we strongly recommend that you use a
proper fitting BenQ projector ceiling mount kit
and that you ensure it is securely and safely
installed.
If you use a non-BenQ brand projector ceiling
mount kit, there is a safety risk that the projector
may fall from the ceiling due to an improper
attachment through the use of the wrong gauge or
length screws.
You can purchase a BenQ projector ceiling mount
kit from the place you purchased your BenQ
projector. BenQ recommends that you also
purchase a separate Kensington lock compatible
security cable and attach it securely to both the
Kensington lock slot on the projector and the base
of the ceiling mount bracket. This will perform the
secondary role of restraining the projector should
its attachment to the mounting bracket become
loose.
14. Do not store the projector on end vertically.
Doing so may cause the projector to fall over,
causing injury or resulting in damage.
Important safety instructions
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly design to deliver high
reliability and ease of use.
The projector offers the following features.
• Three-panel LCD system to deliver superior brightness, color saturation and color depth
• HQV (Hollywood Quality Video) scaler functionality to provide excellent picture quality
employing contrast and clarity enhancement, noise reduction and motion optimization
• Intuitive control over the lens shift lever to provide flexibility in setting-up your projector
• Unique cooling system design to prevent unnecessary fan noise, rated at less than 32dB in
Economic mode
• Selectable password protected function
• High quality manual zoom lens
• Two-way digital keystone correction, pincushion and barrel corrections to correct distorted images
• Ultra-high brightness projection lamp
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and Economic modes to reduce the power consumption
• Powerful AV function to provide high quality video image
• Dynamic iris system to achieve a high contrast ratio of 5000:1
• Component HDTV compatibility
• A wide variety of inputs for connection to your video and PC equipment
•
The apparent brightness of the projected image will vary depending on the ambient lighting conditions,
selected input source contrast/brightness settings, and is directly proportional to projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers specifications.
This is normal and expected behavior.
8
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Shipping contents
The projector is shipped with the cables required for connection to a video and PC equipment. Some of the
items may not be available depending on your region of purchase. Please check with your place of purchase.
Standard accessories
Some of the accessories may vary from region to region, and may differ from those illustrated.
Projector
Remote control and two
AAA batteries
User manual
Quick start guide
User manual CD
Warranty card
Safety manual
Power cable
Component Video cable
Optional accessories
1. HDMI Cable
2. Spare lamp kit
3. Ceiling mount kit
Introduction
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector exterior view
Front and upper side
2. Vent (heated air exhaust)
3. Focus and Zoom adjustment
4. Front IR sensor
5. Projection lens
6. Inlet (cool air intake)
7. Len shift lever
1
2
2
3
6
7
4
5
8. Lens cap
8
Rear side
17 18 19
11 12 13 14
15
16
20
21
10
9
9. Front Adjuster foot
10. AC power cord inlet
11. Rear IR sensor
12. RS-232C port
13. USB socket
17. Composite Video input (RCA)
18. S-Video input (mini 4-pin DIN)
19. 12VDC output terminal
Used to trigger external devices such as an electric screen
or lighting controls, etc. Consult your dealer for how to
connect to these devices.
14. HDMI port
15. RGB socket
16. Component Video inputs (RCA)
Note that the total maximum current must not
exceed 0.5 A.
Support Y/PB/PR or Y/CB/CR video signal
20. Inlet (cool air intake)
21. Kensington anti-theft lock slot
Under side
22. Ceiling mounting bracket screw holes
23. Dust filter grill
24. Lamp cover
9
9
22
23
24
22
10
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and functions
Projector
1
2
9
10
4
6
5
6
11
6
3
12
7
6
8
1. Focus ring
7. MODE
Adjusts the focus of the projected image. See "Fine-
details.
Sequentially selects a predefined picture setting
available for each input. See "1. Selecting a picture
mode" on page 28 for details.
2. Zoom ring
8. ENTER
Adjusts the size of the image. See "Fine-tuning the
image size and clarity" on page 26 for details.
Enacts the selected On-Screen Display (OSD) menu
9. TEMPerature warning light
3.
POWER
Lights up or flashes if the projector’s temperature
on page 47 for details.
47 for details.
4. POWER indicator light
10. LAMP indicator light
Lights up or flashes when the projector is
page 47 for details.
Lights up or flashes when the projector lamp has
information" on page 47 for details.
5. MENU
11. EXIT
Toggles the On-Screen Display (OSD) menu on
details.
Exits and saves any changes made using the On-
Screen Display (OSD) menu. See "Using the menus"
on page 36 for details.
6. Keystone /Arrows buttons (eLeft, cUp, fRight,
dDown)
12. SOURCE
Sequentially selects the input signal D-SUB, HDMI,
Video, S-Video, COMP1 or COMP2. See "Switching
input signal" on page 25 for details.
Manually corrects distorted images resulting from
an angled projection. See "Correcting two-
dimensional keystone" on page 26 for details.
When the On-Screen Display (OSD) menu is
activated, the buttons are used as directional
arrows to select the desired menu items and to
make adjustments. See "Using the menus" on
page 36 for details.
Introduction
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
1.
POWER
1
2
2. Source buttons (COMP1, COMP2, VIDEO, HDMI, D-SUB, S-VIDEO)
Selects an input source for display. See "Switching input signal" on page 25
for details.
3. Aspect buttons (ANA (Anamorphic), 4:3, LB (Letterbox), WIDE, REAL)
Selects the display aspect ratio. See "3. Selecting the aspect ratio" on page 29
for details.
3
4
6
4. MODE
5
7
Selects one of the picture modes (Cinema, Dynamic, Standard, Photo, User
5. MEMORY (1, 2, and 3)
8
Selects User 1, 2 or 3 picture mode. See "1. Selecting a picture mode" on
page 28 for details.
9
10
6. DEFAULT
Restores the default settings for current picture mode. See "1. Selecting a
picture mode" on page 28 for details.
11
7. Arrows buttons (eLeft, cUp, fRight, dDown)
Moves the current On-Screen Display (OSD) menu selection in the direction
8. ENTER
Enacts the selected On-Screen Display (OSD) menu item. See "Using the
menus" on page 36 for details.
12
9. MENU
menus" on page 36 for details.
10. EXIT
Exits and saves any changes made using the On-Screen Display (OSD) menu. See "Using the menus" on
page 36 for details.
11. Picture quality adjustment buttons
12. LIGHT
Turns on the remote control backlight for about 10 seconds. Pressing any other button while the backlight
is on keeps the backlight on for a further 10 seconds. Press the Light button again to turn the backlight off.
12
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the remote control batteries
1. To open the battery cover, turn the
remote control over to view its back,
push on the finger grip on the cover
and slide it down in the direction of
the arrow as illustrated. The cover will
slide off.
2. Remove any existing batteries (if
necessary) and install two new AAA batteries observing the battery polarities as indicated in the base of the
battery compartment. Positive (+) goes to positive and negative(-) goes to negative.
3. Refit the cover by aligning it with the case and sliding it back up into position. Stop when it clicks into place.
•
Do not mix old batteries with new ones, or mix different types of batteries.
•
Avoid leaving the remote control and batteries in an excessive heat or humid environment like the
kitchen, bathroom, sauna, sunroom, or in a closed car.
•
•
Dispose of used batteries according to the battery manufacturer’s instructions and local environment
regulations for your region.
If the remote control will not be used for an extended period of time, remove the batteries to avoid
damage to the control from possible battery leakage.
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the back of the projector. The remote
control must be held at an angle within 45 degrees perpendicular to the projector's IR remote control sensors to
function correctly. The distance between the remote control and the sensors should not exceed 8 meters.
Make sure that there are no obstacles between the remote control and the IR sensors on the projector that
might obstruct the infra-red beam.
•
Operating the projector from the front
•
Operating the projector from the rear
Introduction
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning your projector
Choosing a location
Your projector is designed to be installed in one of four possible installation locations:
1. Floor in front of screen;
2. Ceiling in front of screen;
3. Floor at rear of screen; or
4. Ceiling at rear of screen.
Your room layout or personal preference will dictate which installation location you select. Take into
consideration the size and position of your screen, the location of a suitable power outlet, as well as the location
and distance between the projector and the rest of your equipment.
1. Floor front:
2. Ceiling front:
Select this location with the projector placed near the Select this location with the projector suspended from
floor in front of the screen. This is the most common the ceiling in front of the screen.
way to position the projector for quick setup and
portability.
Purchase the BenQ Projector Ceiling Mounting Kit from
your dealer to mount your projector on the ceiling.
Set Ceiling Front in the System Setup > Projector
Position menu after you turn the projector on.
3. Floor rear:
Select this location with the projector placed near the Select this location with the projector suspended from
floor behind the screen. the ceiling behind the screen.
4. Ceiling rear:
Note that a special rear projection screen is required. Note that a special rear projection screen and the BenQ
Projector Ceiling Mounting Kit are required for this
installation location.
Set Floor Rear in the System Setup > Projector Position
menu after you turn the projector on.
Set Ceiling Rear in the System Setup > Projector
Position menu after you turn the projector on.
14
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining a preferred projected picture size
The distance from the projector lens to the screen, the zoom setting, and the video format each factors in the
projected image size. BenQ has provided separate tables of dimensions for both 16:9 and 4:3 screen ratios to
assist you in determining the ideal location for your projector.
The projector should always be placed horizontally level (like flat on a table), and positioned directly
perpendicular (90° right-angle square) to the horizontal center of the screen. This prevents image distortion
caused by angled projections (or projecting onto angled surfaces).
If the projector is mounted on a ceiling, it must be mounted upside-down so that it projects at a slightly
downward angle.
This projector is equipped with a movable lens. See "Shifting the projection lens" on page 18 for details.
BenQ has provided tables of 16:9-aspect-ratio and 4:3-aspect-ratio screen sizes to assist you in determining the
ideal location for your projector. The vertical offset heights in the dimension tables on page 16 and 17 are
measured when the lens is shifted fully up or down. You can see from the diagrams on page 16 and 17, that this
type of projection causes the bottom edge of the projected image to be vertically offset from the horizontal
plane of the projector. When ceiling mounted, this refers to the top edge of the projected image.
There are two dimensions to consider, the perpendicular horizontal distance from the center of the screen
(projection distance), and the vertical offset height of the projector from the horizontal edge of the screen
(offset).
If the projector is positioned further away from the screen, the projected image size increases, and the vertical
offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for both the projected
image size and the vertical offset dimension, which are directly proportional to the projection distance.
How to determine the position of the projector for a given screen size
1. Determine the aspect ratio of your screen, 16:9 or 4:3?
2. Refer to the table and find the closest match to your screen size in the left columns labelled "Screen
Dimensions". Using this value, look across this row to the right to find the corresponding average distance
from screen value in the column labelled "Average". This is the projection distance.
For example, if you are using a 120-inch, 4:3-aspect-ratio screen, please refer to "4:3 (standard) ratio screen
dimension table". The average projection distance is 5332 mm.
If you place the projector in a different position (to that recommended), you will have to tilt it down or up to
center the image on the screen. In these situations, some image distortion will occur. Use the Keystone function
How to determine the recommended screen size for a given distance
This method can be used for situations where you have purchased this projector and would like to know what
screen size will fit in your room.
The maximum screen size is limited by the physical space available in your room.
1. Determine the aspect ratio of your screen, 16:9 or 4:3?
2. Measure the distance between the projector and where you want to position the screen. This is the projection
distance.
3. Refer to the table and find the closest match to your measurement in the average distance from screen
column labelled "Average". Check that your measured distance is between the min and max distances listed
on either side of the average distance value.
4. Using this value, look across that row to the left to find the corresponding screen diagonal listed in that row.
That is the projected image size of the projector at that projection distance.
For example, if you have a 16:9-aspect-ratio screen and your measured projection distance was 4.5m
(4500mm), please refer to "16:9 (widescreen) ratio screen dimension table". The closest match in the "Average"
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
15
column is 4356 mm. Looking across this row shows that a 3048 mm (30.48 m) screen is required. If you can only
obtain imperial sized screens, the screen size is 10' (120") diagonally.
Installation for a 16:9 ratio screen
Floor Installation
Ceiling Installation
Ceiling
Diagonal
Projection Distance
Screen
Center of the lens
Diagonal
Offset
Center of the lens
Screen
Offset
Projection Distance
Floor
16:9 (widescreen) ratio screen dimension table
Screen Dimensions
Distance from Screen in mm
Vertical Offset in
mm
Diagonal
Feet Inches mm
Width
mm
Height
mm
Min
Max
Highest Lowest
distance
(with max.
zoom)
distance
(with min.
zoom)
Average
lens
lens
position position
3.3
4.2
5.0
5.8
6.7
7.5
8.3
9.2
10.0
10.8
11.7
12.5
13.3
14.2
15.0
15.8
16.7
20.8
40
50
60
70
80
1016
1270
1524
1778
2032
2286
2540
2794
3048
3302
3556
3810
4064
4318
4572
4826
5080
1016
886
498
623
747
872
996
1320
1650
1980
2310
2640
2970
3300
3630
3960
4290
4620
4950
5280
5610
5940
6270
6600
8250
1452
1815
2178
2541
2904
3267
3630
3993
4356
4719
5082
5445
5808
6171
6534
6897
7260
9075
1584
1980
2376
2772
3168
3564
3960
4356
4752
5148
5544
5940
6336
6732
7128
7524
7920
9900
50
62
75
87
-548
-685
-822
1107
1328
1550
1771
1992
2214
2435
2657
2878
3099
3321
3542
3763
3985
4206
4428
5535
-959
100
112
125
137
149
162
174
187
199
212
224
237
249
311
-1096
-1233
-1370
-1507
-1644
-1781
-1918
-2055
-2192
-2329
-2466
-2603
-2740
-3424
90
1121
1245
1370
1494
1619
1743
1868
1992
2117
2241
2366
2491
3113
100
110
120
130
140
150
160
170
180
190
200
250
16
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation for a 4:3 ratio screen
Ceiling Installation
Floor Installation
Ceiling
Diagonal
Projection Distance
Diagonal
Image Height
Screen
Center of the lens
Offset
Center of the lens
Screen
Offset
Projection Distance
Image Height
Floor
4:3 (standard) ratio screen dimension table
Screen Dimensions
Distance from Screen in mm
Vertical Offset in
mm
Diagonal
Feet Inches mm
Width
mm
Height
mm
Min
Max
Highest Lowest
distance
(with max.
zoom)
distance
(with min.
zoom)
Average
lens
lens
position position
3.3
4.2
5.0
5.8
6.7
7.5
8.3
9.2
10.0
10.8
11.7
12.5
13.3
14.2
15.0
15.8
16.7
40
50
60
70
80
1016
1270
1524
1778
2032
2286
2540
2794
3048
3302
3556
3810
4064
4318
4572
4826
5080
813
610
762
914
1615
2019
2423
2827
3230
3634
4038
4442
4846
5249
5653
6057
6461
6865
7268
7672
8076
1777
2222
2666
3110
3554
3999
4443
4887
5332
5776
6220
6665
7109
7553
7997
8442
8886
1939
2424
2909
3394
3878
4363
4848
5333
5818
6302
6787
7272
7757
8242
8726
9211
9696
61
76
91
-671
-838
1016
1219
1422
1626
1829
2032
2235
2438
2642
2845
3048
3251
3454
3658
3861
4064
-1006
-1173
-1341
-1509
-1676
-1844
-2012
-2179
-2347
-2515
-2682
-2850
-3018
-3185
-3353
1067
1219
1372
1524
1676
1829
1981
2134
2286
2438
2591
2743
2896
3048
107
122
137
152
168
183
198
213
229
244
259
274
290
305
90
100
110
120
130
140
150
160
170
180
190
200
There is 3% tolerance among these numbers in the above two tables due to optical component
variations. BenQ recommends that if you intend to permanently install the projector, you should
physically test the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you determine
the exact mounting position so that it best suits your installation location.
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Shifting the projection lens
The lens shift lever at the front side of the projector provides flexibility for installing your projector. It allows the
projector to be positioned off axis from screen center.
The lens shift (offset) is expressed as a percentage of the projected image height or width. It is measured as an
offset from the projected image's vertical or horizontal center. The W500 is equipped with + 110% vertical lens
shift and + 48.8% horizontal shift. You can use the joystick to shift the projection lens in any direction within the
allowable range depending on your desired image position.
•
Vertical lens shift
•
Horizontal lens shift
•
•
The lens shift lever can be secured by turning it clockwise or released by turning it counterclockwise.
Please be careful to not over-tighten it.
Lens shift adjustment will not result in degraded picture quality. In the unlikely event, image distortion
18
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
You can connect the projector to any type of video equipment, such as a VCR, DVD player, digital tuner, cable
or satellite decoder, video game console or digital camera. You can also connect it to a desktop or laptop PC or
Apple Macintosh system.
The projector can be connected to multiple video equipment at the same time by using different cables. All you
need to do is select the appropriate input for the projector to display.
When connecting a signal source to the projector, be sure to:
1. Turn off all equipment before making any connections.
2. Use only the correct type cables for each source with proper type plugs.
3. Ensure that all cable plugs are firmly fitted to the equipment sockets.
Note that all cables shown in the following connection diagrams may not be supplied with the projector
(See page 9 for the shipping contents). Most cables are commercially available from electronics stores.
We recommend that you purchase international standard cables for cable connection.
Connecting a computer
The projector provides a VGA and HDMI input sockets that allow you to connect it to a laptop or desktop
computer.
To connect the projector to a notebook or desktop computer (either through a VGA cable or a
HDMI cable):
•
With a VGA cable:
•
With a HDMI cable:
1. Take a VGA cable and connect one end to the D- 1. Take a HDMI cable and connect one end to the
Sub output socket of the computer.
HDMI output socket of the computer.
2. Connect the other end of the VGA cable to the
D-Sub signal input socket on the projector.
2. Connect the other end of the HDMI cable to the
HDMI signal input socket on the projector.
3. You should also connect the separate audio cable to a suitable audio amplifier.
The final connection path should be like that shown in the following diagram:
Laptop or desktop computer
To audio input
terminals
From audio output
terminals
HDMI cable
or
VGA cable
Many laptops do not turn on their external video ports when connected to a projector. Usually a key
combination like Fn + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol on the laptop. Press Fn and the labeled function key
simultaneously. Refer to your laptop’s documentation to discover your laptop’s key combination.
Connection
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the following output
sockets:
•
•
•
•
HDMI
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the above connecting methods,
however each provides a different level of video quality. The method you choose will most likely depend upon the
availability of matching terminals on both the projector and the Video source device as described below:
Best video quality
The best available video connection method is HDMI. HDMI (High-Definition Multimedia Interface) supports
uncompressed video data transmission between compatible devices like DTV tuners, DVD players and displays
over a single cable. It provides pure digital viewing and listening experience.
If no HDMI source is available, the next best video signal is Component Video (not to be confused with
composite Video). Digital TV tuner and DVD players output Component Video natively, so if available on your
devices, this should be your connection method of choice in preference to (composite) Video.
component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video. If you have both
composite Video and S-Video output terminals on your Video source device, you should elect to use the S-Video
option.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from
your projector, being the least video quality of the available methods described here.
See "Connecting an S-video or a composite Video source device" on page 22 for how to connect the projector to
an S-Video or composite Video device.
Connecting a HDMI device
Examine your Video source device to determine if it has an unused HDMI socket available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a HDMI device:
1. Take a HDMI cable and connect one end to the HDMI output socket of the Video source device.
2. Connect the other end of the HDMI cable to the HDMI input socket on the projector.
3. You should also connect the separate audio cable to a suitable audio amplifier.
20
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
The final connection path should be like that shown in the following diagram:
HDMI device: DVD player, digital tuner, etc.
From audio output
terminals
To audio input
terminals
HDMI cable
•
•
It is not recommended to establish the connection via a DVI to HDMI cable. The weight of the DVI to
HDMI adapter may be pulling down on the HDMI port, causing it to become loose over time.
If the selected video image is not displayed after the projector is turned on and the correct video
source has been selected, please check that the video source device is turned on and operating
correctly. Also check that the signal cables have been connected correctly.
Connecting a Component-Video source device
Examine your Video source device to determine if it has a set of unused Component Video output sockets
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a Component Video cable and connect one end to the Component Video output sockets of the Video
source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to
red.
2. Connect the other end of the Component Video cable to the COMPONENT sockets on the projector. Match
the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.
3. You should also connect the separate audio cable to a suitable audio amplifier.
The final connection path should be like that shown in the following diagram:
AV equipment: DVD player, digital tuner, etc.
To audio input
terminals
From audio output
terminals
Component cable
If you connect the projector to a High Definition TV (HDTV) tuner, the following standards are supported:
•
•
•
•
480i
576i
•
•
480p
576p
720p (50/ 60 Hz)
1080i (50/ 60 Hz)
•
1080p (24/ 50/ 60 Hz)
If the selected video image is not displayed after the projector is turned on and the correct video source
has been selected, please check that the video source device is turned on and operating correctly. Also
check that the signal cables have been connected correctly.
Connection
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an S-video or a composite Video source device
Examine your Video source device to determine if it has an unused S-Video or composite Video output socket
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
If you have already made a Component Video connection between the projector and the video source device, you
need not connect to this device again using an S-Video or composite Video connection as this makes an
unnecessary second connection of poorer picture quality. You need only connect using a composite Video
connection if both Component Video and S-Video are not supplied on the video source device (for example,
with some analog video cameras). If S-Video connectivity is available, you should use it in preference to using
composite Video.
To connect the projector to an S-Video or a composite Video source device (either through an S-
Video cable or a Video cable):
•
With an S-Video cable:
•
With a Video cable:
1. Take an S-Video cable and connect one end to
the S-Video output socket of the Video source
device.
2. Connect the other end of the S-Video cable to
the S-VIDEO socket on the projector.
1. Take a Video cable and connect one end to the
Video output socket of the Video source device.
2. Connect the other end of the Video cable to the
VIDEO socket on the projector.
3. You should also connect the separate audio cable to a suitable audio amplifier.
The final connection path should be like that shown in the following diagram:
AV equipment: DVD player,
digital tuner, etc.
Video cable
To audio input
terminals
From audio output
terminals
S-Video cable
•
•
Do not connect both S-Video and composite Video cables from the same video source device at the
same time. You should only ever connect one or the other. See "Connecting Video source devices" on
page 20 for details.
If the selected video image is not displayed after the projector is turned on and the correct video source
has been selected, please check that the video source device is turned on and operating correctly. Also
check that the signal cables have been connected correctly.
22
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the projector
Start up
1. Plug the power cord into the projector and into a wall socket. Turn on
the wall socket switch (where fitted). Check that the Power indicator
on the projector lights orange after power has been applied.
The power cable used in the illustration may look different to the
power cable type used in your region. Use only the power cable as
supplied with the projector, and which is suitable for your region.
2. Remove the lens cap. If it is left on, it could become deformed due to
the heat produced by the projection lamp.
3. Press the
POWER on the projector or remote
control to turn the projector on. The Power indicator
light flashes green and stays green when the projector
is on.
The start up procedure takes about 30 seconds. In the
later stage of start up, a startup logo is projected.
(If necessary) Rotate the focus ring to adjust the
image clearness.
•
•
The projector will not respond to further
commands whilst it is warming up.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the lamp.
4. If you are prompted for a password, press the arrow buttons to enter a six digit password. See "Utilizing the
password function" on page 24 for details.
5. Switch on all of the connected equipment.
The projector will start to search for input signals. The current input source being scanned displays in the
center of the screen. The searching message will continue displaying until an input source signal is found.
You can press SOURCE on the projector or remote control to display the selection bar and switch between
If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the
message 'Out of Range' displayed on a blank screen. Please change to an input signal which is
compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on
page 51 for details.
Using the projector
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option for setting up
password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD
You will be inconvenienced if you activate the password functionality and subsequently forget the
password. Print out this manual (if necessary) and write the password you used in this manual, and keep
the manual in a safe place for later recall.
Setting a password
Once a password has been set and activated, the projector cannot be used unless the correct password is
entered every time the projector is started.
1. Open the OSD menu and go to the Advanced Setup > Password menu. Press ENTER.
2. Highlight Password and select On by pressing eLeft orfRight.
3. A prompt will display on the screen.
4. As pictured to the right, the four arrow buttons (cUp, fRight,
INPUT PASSWORD
dDown, eLeft) respectively represent 4 digits (1, 2, 3, 4). Press the
arrow buttons to enter six digits for the password.
Once the password is set, the OSD menu returns to the Password
page.
IMPORTANT: The digits being input will display as asterisks on-
screen. Write your selected password down here in this manual in
advance or right after the password is entered so that it is available
Back
EXIT
to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5. Press EXIT to go back to the previous page, or press MENU to leave the OSD menu.
If you forget the password
If the password function is activated, you will be asked to enter the six digit
password every time you turn on the projector. If you enter the wrong
password, the password error message as pictured to the right displays
lasting for three seconds, and the 'INPUT PASSWORD' message follows.
You can retry by entering another six-digit password, or if you did not
record the password in this manual, and you absolutely do not remember
Password Error
Please try again.
it, you can use the password recall procedure. See "Entering the password recall procedure" on page 24 for details.
If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short
time.
Entering the password recall procedure
Press MODE on the projector or remote control. The projector will
display a coded number on the screen. Write down the number and turn
RECALL PASSWORD
off your projector. Seek help from the local BenQ service center to
decode the number. You may be required to provide proof of purchase
documentation to verify that you are an authorized user of the
projector.
Please write down the recall code,
and contact with the BenQ
Customer Center.
Recall code:
0 2 1 2
EXIT Back
24
Using the projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the password
1. Open the OSD menu and go to the Advanced Setup > Password menu. Press ENTER.
2. Highlight Change Password. Press ENTER.
3. The message 'INPUT CURRENT PASSWORD' displays. Enter the old password.
i. If the password is correct, another message 'INPUT NEW PASSWORD' displays.
ii. If the password is incorrect, the password error message displays lasting for three seconds, and the
message 'INPUT CURRENT PASSWORD' displays for your retry. You can press EXIT to clear and re-
enter six digits or go back to the previous page.
4. Enter a new password.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password
down here in this manual in advance or right after the password is entered so that it is available to you
should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to enter the new password next
time the projector is started.
7. Press EXIT to go back to the previous page, or press MENU to leave the OSD menu.
Disabling the password function
To disable password protection:
1. Go back to the Advanced Setup > Password > Password menu after opening the OSD menu system.
2. Select Off by pressing eLeft orfRight. The message 'INPUT PASSWORD' displays.
3. Enter the current password.
i. If the password is correct, the OSD menu returns to the Password page with 'Off' shown in the row of
Password. You will not have to enter the password next time when turning on the projector.
ii. If the password is incorrect, the password error message displays lasting for three seconds, and the
message 'INPUT PASSWORD' displays for your retry. You can press EXIT to cancel the change or try
another password.
Though the password function is disabled, you need to keep the old password in hand should you ever
need to re-activate the password function by entering the old password.
Switching input signal
The projector can be connected to multiple equipment at the same time. However, it can only display one at a
time.
•
•
To select an individual input signal, press one of the
Source buttons on the remote control.
To sequentially cycle through all possible sources,
press SOURCE on the projector, and the source
selection bar displays. Press cUp ordDown
repeatedly until your desired signal is selected and
press ENTER. If there is multiple equipment
connected to the projector, you can press the key again
to search for another signal.
Activating automatic source search
Be sure the Auto Source Search in the System Setup menu is activated if you want the projector to automatically
search the signals. Go to the System Setup > Auto Source Search menu and select On by pressing eLeft
orfRight. The projector will scan for input signals until it acquires a signal. If the function is not activated, the
projector selects the last used input signal.
Using the projector
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Speeding up the process of source search
You can speed up the process of source search by blocking source(s) not in use.
1. Go to the Advanced Setup > Source Block menu and press ENTER.
2. Highlight the input source with cUp ordDown.
3. Decide whether to Search or Skip it during input signal detection with eLeft orfRight.
4. Repeat Step 2 and 3 until you are satisfied with the settings.
5. Press EXIT/MENU to exit and save the settings.
Blocking all sources at the same time is not allowed.
Adjusting the projected image
Adjusting the projection angle
There are two adjuster feet on the bottom of the projector. These
can be used if necessary to change the projection angle. Screw the
feet in or out as appropriate to aim and level the projection angle.
The lens shift lever adjacent to the projection lens can further
assist you in determining the position of the projected image. See
"Shifting the projection lens" on page 18 for details.
If the screen and the projector are not perpendicular to each other, the projected image becomes vertical
trapezoidal. To correct this situation, see "Correcting two-dimensional keystone" on page 26 for details.
Fine-tuning the image size and clarity
1. Adjust the projected image to the size that you need 2. Then sharpen the image by rotating the focus ring.
using the zoom ring.
Correcting two-dimensional keystone
Keystoning occurs when the projector is not perpendicular
to the screen and is where the projected image displays
visible as a trapezoid shape like either of the following:
•
Two parallel sides (left and right, or top and bottom)
but is noticeably wider on either side.
No parallel sides.
•
To correct the image's shape, you can perform the
following steps.
1. Adjust the projection angle. Move the projector to be in
front of the center of the screen with the base of the lens
level with the top or bottom edge of the screen.
2. If the image is stilled distorted, or the projector is unable to be positioned as described above, you will need to
manually correct the image following ONE of these steps.
26
Using the projector
Download from Www.Somanuals.com. All Manuals Search And Download.
• Press one of the Keystone/Arrow buttons (
/
,
/
,
/
,
/
) on
2D Keystone
the projector or remote control to display the 2D Keystone correction page.
Press the button whose keystone icon is similar to the adjustment you are about
to make. For example, the Up button (
/
) will widen the upper side and
reduce the bottom side of the picture. Continue pressing the same button or
press the other buttons until you are satisfied with the shape.
• Press MENU on the projector or remote control. Go to the Display > Keystone
menu and press ENTER. Highlight 2D Keystone and press ENTER to display
Back
EXIT
the Keystone correction page. Press one of the Keystone/Arrow buttons (
/
,
/
,
/
,
/
) on the projector or remote control whose keystone
icon is similar to the adjustment you are about to make. Continue pressing the same button or press the
other buttons until you are satisfied with the shape.
The values on the lower portion of the page change while pressing. When the values reach their maximum or
minimum with repeated button presses, the image's shape will stop changing. You will not be able to change
the image further in that direction.
•
Two parallel sides (left and right, or top and bottom) but is noticeably wider on either side
•
•
To widen the upper side, press
or
/
•
•
To widen the bottom side, press
or
/
Go to the Display > Keystone menu.
Enter the 2D Keystone correction page
Go to the Display > Keystone menu.
Enter the 2D Keystone correction page
and press
/
repeatedly until the
and press repeatedly until the
/
image’s shape becomes square.
image’s shape becomes square.
•
No parallel sides
3. To widen the upper
side, press
4. Press EXIT/MENU to exit and save the
settings.
1. To widen the left side, press
/
or
/
repeatedly until the
image is square.
2. Go to the Display > Keystone menu. Enter
the 2D keystone correction page and press
/
.
Correcting pincushion and barrel distortion
Sometimes, your projected image may suffer from pincushion or barrel distortion due to the curved projection
surface.
•
•
Pincushion distortion
Horizontal and vertical lines bend inwards toward the center of the picture. The distortion is most noticeable
at the four edges of the picture.
Barrel distortion
Horizontal and vertical lines bend outwards toward the edge of the picture. The distortion is most noticeable
at the four edges of the picture.
Using the projector
Download from Www.Somanuals.com. All Manuals Search And Download.
27
To correct the image's shape, you can perform the following steps.
1. Press MENU on the projector or remote control. Go to the Display > Keystone menu and highlight
Pincushion Correction.
2. Press eLeft orfRight repeatedly to adjust the image until you are satisfied with the shape.
The values on the adjustment bar of the page change while pressing. When the values reach their maximum or
minimum with repeated button presses, the image's shape will stop changing. You will not be able to change the
image further in that direction.
• Pincushion distortion
1. Go to the Display > Keystone menu.
2. Highlight Pincushion Correction and press
/
repeatedly until the image’s shape becomes square.
• Barrel distortion
1. Go to the Display > Keystone menu.
2. Highlight Pincushion Correction and press
repeatedly until the image’s shape becomes square.
/
Optimizing the image
To optimize the image, use the remote control or on-screen menus. For the operation of on-screen menus, please
The following steps are optional. You do not need to follow every step. It depends on the image quality you
desire.
1. Selecting a picture mode
Select a picture mode on the remote control, or in the Picture--Basic > Picture
Mode menu. You can also press MODE on the control panel or remote control
repeatedly until your desired mode is selected. There are 7 modes available for
3
each input. These modes consist of preset values suitable for various projection
situations as described below:
1
•
•
•
Dynamic Mode: Maximizes the brightness of the projected image. This mode
is suitable for environments where extra-high brightness is required, such as
using the projector in well lit rooms.
Cinema Mode: With well-balanced color saturation and contrast with a low
brightness level. This is most suitable for enjoying movies in a totally dark
environment (as you would find in a commercial cinema).
Standard Mode: Is slightly brighter than Cinema Mode, and suitable for use in
rooms where there is a small amount of ambient light.
2
•
•
Photo Mode: Designed for viewing digital pictures in a living room.
User 1/User 2/User 3 modes" on page 29 for details. These three modes can
also be selected directly by pressing the Memory 1/2/3 buttons on the remote
control.
If you are not satisfied with the picture quality made by the preset picture
modes. You can manually adjust the settings through the Picture--Basic and Picture--Advanced menus.
2 8
U
s in g th e p ro je c to r
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the User 1/User 2/User 3 modes
There are three user-definable modes if the current available picture modes are not suitable for your need. You
can use one of the picture modes (except the User 1/2/3) as a starting point and customize the settings.
1. Go to the Picture--Basic > Picture Mode menu.
2. Press eLeft orfRight to select User 1, User 2 or User 3.
3. Press dDown to highlight Load Settings From and press ENTER.
4. Press cUp ordDown to highlight a picture mode that is closest to your need and press ENTER.
5. Press EXIT to go back to the previous page and press dDown to select a menu item to be changed and adjust
the value with eLeft orfRight.
6. You can also press EXIT and then press fRight to go to the Picture--Advanced menu for further picture
Renaming the User 1/User 2/User 3 modes
To rename the user-definable modes, you can perform the following steps.
1. Go to the Picture--Basic > Rename User Mode menu and press ENTER.
2. Press cUp ordDown to highlight User 1, User 2 or User 3 and press ENTER.
3. Press eLeft orfRight to select a character position.
4. Assign a letter or a number to this character position by pressing cUp ordDown repeatedly. Press cUp to
select individual letters in alphabetical order, or press dDown to select in reverse order. Capital letters,
lowercase letters, numbers from 0 to 9, and a blank space are provided to you.
5. Repeat Step 3 and 4 until you are satisfied with the new name.
•
The maximun length is 12 digits.
•
The first character cannot be a space.
6. When finished, press ENTER to save the settings.
2. Adjusting picture quality
You can adjust Brightness, Contrast, Color, Tint and Sharpness settings using the Picture--Basic menu or with
•
All settings in the Picture--Basic menu will take effect right away and be saved to the picture mode that
you select.
•
Some picture adjustments are available only when certain input ports are in use. Unavailable
adjustments are not shown on the screen.
3. Selecting the aspect ratio
The "aspect ratio" is the ratio of the image width to the image height. Most analog TV signals and computers
are in 4:3 ratio and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can dynamically stretch
and scale the image output to a different aspect than that of the image input source. Images can be stretched in
a linear manner so the whole of the image is stretched equally, or non-linearly, which distorts the image.
You can change the projected image ratio (no matter what aspect the source is) by using the Aspect buttons on
the remote control or in the Display > Aspect Ratio OSD menu. Select an aspect ratio to suit the format of the
video signal and your display requirements. There are five aspect ratios available:
Using the projector
Download from Www.Somanuals.com. All Manuals Search And Download.
29
In the pictures below, the black portions are inactive areas and the white portions are active areas.
1. Anamorphic: (displayed as
"ANA" on the remote
control) Scales an image so
that it is displayed in the
center of the screen with a
16:9 aspect ratio.
4. Wide: A 4:3 aspect ratio image is enlarged
NON-linearly in horizontal direction to
accommodate 16:9 full-screen display. This
stretches only the right and left sides of the
image; the central part is unchanged.
2. 4:3: Scales an image so that it
is displayed in the center of
the screen with a 4:3 aspect
ratio.
5. Real: One-to-one mapping is performed on the
input signal without any scaling with the image
displayed at the center of the screen.
3. Letterbox: (displayed as "LB"
on the remote control)
Enlarges an image with
letterbox format to display it
in full-screen format with a
16:9 aspect ratio. The upper
and lower portions of the image are cropped.
The Anamorphic setting stretches and resizes linearly, except that it treats the vertical and horizontal dimensions
independently. It stretches the height of the source image until it reaches the full projected height, and stretches
the width of the source image until it reaches the full projected width. This may alter the projected aspect,
depending upon the original aspect of the source image. Anamorphic is most suitable for images which are
already in a 16:9 aspect, like high definition TV, as it displays them without aspect alteration.
The 4:3 setting is most suitable for 4:3 images like standard definition TV and 4:3 aspect DVD movies, as it
displays them without aspect alteration.
The Letterbox setting resizes an image proportionately both vertically and horizontally from the width of a 4:3
aspect to the width of a 16:9 aspect and centers it on-screen. This produces an image greater in height than can be
displayed, so part of the image is lost (not displayed) along the top and bottom edges of the projection. This is
suitable for the display of movies which are presented in letterbox format (with black bars top and bottom).
The Wide setting stretches the image horizontally in a non-linear manner, that is, the edges of the image are
stretched more than the centre of the image, to prevent distortion of the central part of the image. This is suitable
for occasions where you want to stretch the width of a 4:3 aspect image to the width of a 16:9 aspect screen. It
does not alter the height. Some widescreen movies have been produced with their width squashed down to the
width of a 4:3 aspect, and are best viewed when restretched back to their original width using the Wide setting.
The Real setting displays the image in a one-to-one pixel mapping without alteration or resize in the centre of the
projection. This is most suitable for use with PC and RGBHD source inputs.
Advanced picture quality controls
There are more advanced user-definable functions in the Picture--Advanced menu.
All settings in the Picture--Advanced menu will take effect right away and be saved to the picture mode
that you select.
Setting black level
1. Go to the Picture--Advanced menu and highlight Black Level.
2. Press eLeft orfRight to select 0 IRE or 7.5 IRE.
The grayscale video signal is measured in IRE units. In some areas which use NTSC TV standard, the grayscale is
measured from 7.5 IRE (black) to 100 IRE (white); however, in other areas which use PAL equipment or Japanese
NTSC standard, the grayscale is measured from 0 IRE (black) to 100 IRE (white). We suggest that you check the
input source if it is with 0 IRE or 7.5 IRE, then select accordingly.
30
Using the projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting picture clarity
1. Go to the Picture--Advanced menu and highlight Clarity Control.
2. Press ENTER.
3. Press cUp ordDown to highlight one of the following functions and press eLeft orfRight to adjust the
setting.
•
•
•
•
Noise Reduction: Reduces electrical image noise. The higher the setting, the less the noise.
Detail Enhancement: The higher the setting, the more details the image reveals.
Luma Transmission: Enhances contour details. The higher the setting, the more distinct the effect.
Chroma Transmission: Reduces color smear. The higher the setting, the more distinct the effect.
4. Repeat Step 3 until you are satisfied with the picture clarity.
Selecting a color temperature
1. Go to the Picture--Advanced menu and highlight Color Temp.
2. Press eLeft orfRight to select from one of the following settings.
•
Lamp Native: With factory default color temperature and higher brightness. This setting is suitable for
environments where high brightness is required, such as using the projector to project slides in well lit
rooms.
•
•
•
Warm: Makes pictures appear reddish white.
Normal: Maintains normal colorings for white.
Cool: With the highest color temperature, making pictures appear bluish white.
•
User 1/User 2/User 3: recalls the customized settings in the Color Temp User Fine Tuning menu. See
"Setting a preferred color temperature" on page 31 for details.
About color temperatures:
There are many different shades that are considered to be “white” for various purposes. One of the
common methods of representing white color is known as the “color temperature”. A white color with a
low color temperature appears to be reddish white. A white color with a high color temperature appears
to have more blue in it.
Setting a preferred color temperature
This function is only available when the color temperature is set as User 1/User 2/User 3.
1. Go to the Picture--Advanced menu and highlight Color Temp.
2. Press eLeft orfRight to select User 1, User 2 or User 3.
3. Press dDown to highlight Color Temp User 1/2/3 Fine Tuning.
4. Press cUp ordDown to highlight the item you want to change and adjust the values with eLeft orfRight.
•
•
•
•
•
•
Red Gain: Adjusts the contrast level of Red.
Green Gain: Adjust the contrast level of Green.
Blue Gain: Adjusts the contrast level of Blue.
Red Offset: Adjusts the brightness level of Red.
Green Offset: Adjusts the brightness level of Green.
Blue Offset: Adjusts the brightness level of Blue.
5. Press EXIT/MENU to exit and save the settings.
Using the projector
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Color management
In most installation situations, color management will not be necessary, such as in classroom, meeting room, or
lounge room situations where lights remain on, or where building external windows allow daylight into the
room.
Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home
theaters, should color management be considered. Color management provides fine color control adjustment to
allow for more accurate color reproduction, should you require it.
Proper color management can only be achieved under controlled and reproducible viewing conditions. You will
need to use a colorimeter (color light meter), and provide a set of suitable source images to measure color
reproduction. These tools are not provided with the projector, however, your projector supplier should be able to
provide you with suitable guidance, or even an experienced professional installer.
The Color Management provides six sets (RGBCMY) of colors to be adjusted. When you select each color, you
can independently adjust its range and saturation according to your preference.
If you have purchased a test disc which contains various color test patterns and can be used to test the color
presentation on monitors, TVs, projectors, etc. You can project any image from the disc on the screen and enter
the Color Management menu to make adjustments.
To adjust the settings:
1. Go to the Picture--Advanced menu and highlight Color Management.
2. Press ENTER and the Color Management page displays.
3. Highlight Primary Color and press eLeft orfRight to select a color from among Red, Yellow, Green, Cyan,
Blue, or Magenta.
4. Press d to highlight Range and press eLeft orfRight to select its range. Increase in the range will include
colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for how the colors relate to
each other.
For example, if you select Red and set its range at 0, only pure red in the
Yellow
GREEN
RED
projected picture will be selected. Increasing its range will include red
close to yellow and red close to magenta.
5. Press d to highlight Saturation and adjust its values to your preference
by pressing eLeft orfRight. Every adjustment made will reflect to the
image immediately.
Cyan
Magenta
BLUE
For example, if you select Red and set its value at 0, only the saturation
of pure red will be affected.
6. Repeat steps 3, 4 and 5 for other color adjustments.
7. Make sure you have made all of the desired adjustments. If you are not satisfied with the result, you may go to
the Picture--Basic > Reset Picture Settings menu, enter it for returning to the factory preset values.
8. Press EXIT/MENU to exit and save the settings.
Activating the blue filter
After making color adjustments, you can project the color bar test image from the test disc to test the level of
color saturation by activating the blue filter instead of looking through color filters. Turning on the blue filter will
disable all Red and Green channel output, allowing only the Blue color to be displayed on the screen. Please refer
to the instructions on the test disc for how to check the accuracy of different colors.
To activate the blue filter:
1. Go to the Picture--Advanced menu and highlight Blue Filter.
2. Press eLeft orfRight to toggle the blue filter on and off. The setting will take effect immediately.
32
Using the projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating in a high altitude environment
We recommend that you use the High Altitude Mode when your environment is higher than 3200 feet above
sea level, or is hotter than 40°C.
To activate High Altitude Mode:
1. Press MENU to turn the OSD menu on and press eLeft orfRight to select Advanced Setup.
2. Press cUp ordDown to highlight High Altitude Mode.
3. Press eLeft orfRight to select On.
4. A confirmation message displays. Highlight Yes and press ENTER.
WARNING
High Altitude Mode is used when the
environment is higher than 3200
feet, or the temperature is over
40°C.
Do you want to turn the High Altitude
Mode on?
No
Yes
Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased
fan speed necessary to improve overall system cooling and performance.
If you use this projector under other extreme conditions excluding the above, it may display auto shut-down
symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch
to High Altitude mode to solve these symptoms. However, this is not to state that this projector can operate
under any and all harsh or extreme conditions.
Searching for details on the projected image
If you need to find the details on the projected image, you can perform the following steps.
1. Go to the Display > Digital Zoom menu.
2. Press eLeft orfRight on the projector or remote control repeatedly to magnify the image until you are
satisfied with the image size. The image can be magnified up to 300%.
3. Press dDown to highlight Pan and press ENTER to display the Pan page.
4. Use the Keystone/Arrow buttons (
navigate the image.
/
,
/
,
/
,
/
) on the projector or remote control to
5. Press EXIT to go back to the previous page.
6. To restore the image to its original size, go to the Display > Digital Zoom menu and press 3Left to reduce
the size of the image.
Creating your own startup screen
In addition to selecting the projector preset startup screen from between BenQ logo and Blue screen, you can
make your own startup screen that is an image projected from your computer or video source.
1. Project the image you want to use as your startup screen from either a computer or video source.
2. Go to the System Setup > My Screen menu, press ENTER.
3. A confirmation message displays. Press ENTER again.
4. The message 'Screen Capturing' displays while the projector is processing the image. Please wait.
5. If the action is successful, you see the message 'Captured Succeeded' on the screen. The captured image is
saved as My Screen.
6. To view the captured image displayed as the startup screen, set My Screen in the System Setup > Splash
Screen menu and restart the projector.
In the unlikely event, the capturing action failed. If so, change your target image.
Using the projector
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Personalizing the projector menu display
The On Screen Display (OSD) menus can be set according to your preferences. These settings do not affect the
projection settings, operation, or performance.
•
•
•
Language in the System Setup menu sets your familiar language for the on-screen menus.
You can select the projector’s Background Color from black, blue or purple in the System Setup menu.
Menu Display Time in the System Setup > Menu Settings menu sets the length of time the OSD will remain
active after the last button press.
•
Menu Position in the System Setup > Menu Settings menu adjusts the OSD position on the screen.
Turning the power off
POWER OFF
1. Press
POWER on the projector or remote
control and a prompt message appears. Press
Press
button again to
power off
POWER a second time to turn the projector
off.
Press any button to cancel
2. The Power indicator light flashes orange,the
lamp shuts down, and the fans continue to run
for approximately 140 seconds to cool down the
projector.
To protect the lamp, the projector will not
respond to any commands during the cooling process.
3. The Power indicator light is a steady orange once the cooling process
has finished and fans stop.
4. Disconnect the power cord from the wall socket.
34
Using the projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Menus
On Screen Display (OSD) structure
Picture--Basic
Picture Mode
Load Settings From
Brightness
Dynamic
Cinema
Standard
Photo
Dynamic
Cinema
Standard
Photo
Contrast
Color
User 1
Tint
User 1
User 2
Sharpness
User 2
User 3
Reset Picture Settings
Rename User Mode
User 3
Noise Reduction
Lamp Native
Warm
Normal
Cool
Detail Enhancement
Luma Transmission
Chroma Transmission
Picture--Advanced
Black level
Clarity Control
Color Temp.
User 1
User 2
User 3
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Color Temp. Fine Tuning
Color Management
Dynamic IRIS
Color Space Transfer
Blue Filter
Primary Color
Range
Saturation
Red
Default
RGB
YUV
Yellow
Green
Cyan
Blue
Display
Aspect Ratio
Magenta
Keystone
Position
Overscan Adjustment
Digital Zoom
2D Keystone
Pincushion Correction
Anamorphic
4:3
Letter Box
Wide
Pan
H.Size
Phase
Auto
PC & Component YPbPr Tuning
Real
17 languages
System Setup
Language
BenQ
Splash Screen
My Screen
Projector Position
Auto Off
Blue
My Screen
Floor Front
Ceiling Front
Floor Rear
Ceiling Rear
Black
Blue
Sleep Timer
Background Color
Menu Settings
Input Source
Auto Source Search
Purple
Menu Display Time
Menu Position
Menu Transparency
D-Sub
HDMI
Video
S-Video
Component 1
Component 2
Normal
ECO
Lamp Power
Lamp Hours
Reset Lamp Timer
Lamp Hours Nor.
Lamp Hours Eco.
Lamp Rest Rate
Advanced Setup
Lamp Settings
Pattern
Dust Filter
Dust Filter Hours
Grid
High Altitude Mode
Password
Reset Dust Filter Time
Color Bar
Key Lock
D-Sub
Password
Source Block
Reset All Settings
HDMI
Video
Change Password
S-Video
Component 1
Component 2
Menus
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Information
Source
Picture Mode
Resolution
Lamp Hours Nor.
Lamp Hours Eco.
Lamp Rest Rate
Dust Filter Hour
If there is no equipment connected or no signal detected, limited menu items are accessible.
Using the menus
The projector is equipped with on-screen display (OSD) menus for making various adjustments and settings.
Below is the overview of the English OSD menu.
Main menu icon
Picture -- Basic
Main menu
Highlight
Cinema Mode
Picture Mode
Load Settings From
Brightness
Sub-menu
Contrast
Color
Status
Tint
Sharpness
Reset Picture Settings
Rename User Mode
Press EXIT to
the previous
page or to
exit.
S-VIDEO
Current input signal
EXIT Back
The following example describes the adjustment of the keystone.
1. Press MENU on the projector or remote
control to turn the OSD menu on.
4. Press ENTER and press Up/ Down to select 2D
Keystone.
Keystone
2D Keystone
ENTER
Picture -- Basic
Pincushion Correction
Picture Mode
Cinema Mode
Load Settings From
Brightness
Contrast
Color
Tint
Sharpness
Reset Picture Settings
Back
EXIT
Rename User Mode
5. Press ENTER to display the keystone correction page.
2D Keystone
S-VIDEO
EXIT Back
2. Use Left/ Right to select the Display
menu.
3. Press Up/ Down to select Keystone.
Display
Aspect Ratio
Keystone
ENTER
EXIT Back
Position
Overscan Adjustment
6. Based on the image shape displayed on the screen, press
Digital Zoom
Pan
PC & Component YPbPr
the keystone buttons (
/
Up,
/
Left,
/
Down,
/
Right) to adjust the image to a rectangular or square
one.
7. Press EXIT/MENU on the projector or remote control to
exit and save the settings.
S-VIDEO
EXIT Back
36
Menus
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture--Basic menu
The Picture--Basic menu allows you to adjust the finer details of the projected image quality.
Before making adjustments, you are suggested to choose a desired picture mode in this menu which has set
some certain values in order to meet different lighting environment and presentation purposes.
FUNCTION (default
DESCRIPTION
setting / value)
Picture modes are provided so you can optimize your projector image set-up to suit
Picture Mode
(D-sub (Analog
RGB)/HDMI:
Standard;
S-Video/
Component/
Video: Standard)
Loads the settings from one of the preset picture modes and three User Modes. This
function is only available when the picture mode is set as User 1/2/3. See "Setting the
User 1/User 2/User 3 modes" on page 29 for details.
Load Settings
From
Adjusts the brightness of the image.
The higher the value, the brighter the
image. And lower the value, the
darker the image. Adjust this control
Brightness (50)
+50
+70
+30
so the black areas of the image appear
as black and that detail in the dark areas is visible.
Adjusts the degree of difference
between dark and light in the
image. The higher the value, the
greater the contrast.
Contrast (50)
Color (50)
+50
+70
+30
Increase or decrease the color intensity of the image. The higher the value, the more
vivid and brighter the color.
Adjusts the color tones of the image. The higher the value, the more greenish the
picture becomes. The lower the value, the more purplish the picture becomes.
Tint (0)
Adjusts the picture sharpness. The higher the value, the sharper the picture.
Sharpness (0)
Returns the image settings of the current picture mode to the factory preset values.
Reset Picture
Settings
If the User 1/User 2/User 3 has been renamed, the new name will remain
unchanged.
Changes User 1/2/3 to your desired name. See "Renaming the User 1/User 2/User 3
modes" on page 29 for details.
Rename User
Mode
Menus
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture--Advanced menu
The Picture--Advanced menu allows you to adjust the finer details of the projected image quality.
FUNCTION (default
DESCRIPTION
setting / value)
Black Level (0
IRE)
Clarity Control
Color Temp.
Color Temp. Fine
Tuning
Color
Management
Toggles Dynamic IRIS between On and Off.
Dynamic IRIS (On)
When using certain European TV setup boxes found with YUV color encoding
system, press eLeft orfRight to select YUV as this will allow images to display
normally.
Color Space
Transfer (Default)
Blue Filter (Off)
Display menu
Use this menu to set the way that the projector displays the picture.
FUNCTION (default
DESCRIPTION
setting / value)
There are a few aspect ratios that can be selected for different input signals. See "3.
Selecting the aspect ratio" on page 29 for details.
Aspect Ratio
(Anamorphic)
Corrects for trapezoidal distortion resulting from the angle of projection and
pincushion distortion of the image.
•
2D Keystone (0): Corrects any keystoning of the image. See "Correcting
two-dimensional keystone" on page 26 for details.
Keystone (0)
Position (0)
•
Pincushion Correction (0): Corrects any pincushion distortion of the
details.
Displays the position adjustment page. To move the projected image, use the
directional arrow buttons. The values shown on the lower position of the page
change with every button press you made until they reach their maximum or
minimum.
This function is only available with a D-sub (analog RGB) signal selected.
Slightly magnifies and stretches the picture to remove the less brighter image areas
commonly found towards the four edges.
Overscan
Adjustment (0)
Magnifies the projected image. See "Searching for details on the projected image"
on page 33 for details.
Digital Zoom
(100%)
38
Menus
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays the Pan page for searching the details of the projected image by using the
directional arrow buttons on the projector or remote control after the image is
Pan (Central)
The following settings are only available with a PC or DTV RGB signal selected.
•
H. Size (0): Adjusts the frequency of the sampling clock that captures the
input signal.
PC & Component
YPBPR Tuning
•
•
Phase (0): Adjusts the phase of the clock.
Auto: Adjusts the phase, and frequency automatically.
System Setup menu
This menu contains items necessary for basic image setup.
FUNCTION (default
setting / value)
DESCRIPTION
Sets the language for the OSD menus. There are 17 languages for your choice:
English (default), French, German, Italian, Spanish, Russian, Traditional Chinese,
Simplified Chinese, Japanese, Korean, Swedish, Dutch, Turkish, Czech, Portuguese,
Thai, and Polish.
Language
(English)
Allows you to select which logo screen will display during projector startup. Three
options are available: BenQ logo, Blue screen or My Screen.
Splash Screen
(BenQ)
Captures and stores the projected image as My Screen. See "Creating your own
startup screen" on page 33 for details.
My Screen
The projector can be installed on a ceiling or behind a screen, or with one or more
mirrors. There are four settings for choice. Contact your dealer for the ceiling
mount bracket if you need to install the projector on a ceiling. See "Choosing a
location" on page 14 for details.
ProjectorPosition
(Floor Front)
This function allows the projector to turn off automatically after your last button
press when no input signal is detected.
To set the Auto Off time, go to the System Setup > Auto Off menu and press eLeft
orfRight to set a time from 5 to 30 minutes in 5-minute increments.
Auto Off (Disable)
The setting will remain the next time you turn on the projector.
Sets the auto-shutdown timer. The timer can be set to a value between 30 minutes
and 360 minutes.
Sleep Timer
(Disable)
Allows you to choose the color of the background screen that will be displayed
when there is no input signal detected.
Background
Color (Blue)
•
•
•
Menu Display Time (10 sec): Sets the length of time the OSD will remain
active after your last button press. The range is from 5 to 30 seconds.
Menu Position (Center): Adjusts the horizontal and vertical position of the
OSD.
Menu Settings
Input Source
Menu Transparency (0): Adjusts the transparency level of the OSD.
Sets whether the projector searches automatically for input signals. See "Activating
automatic source search" on page 25 for details.
Auto Source
Search (On)
Menus
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup menu
FUNCTION (default
setting / value)
DESCRIPTION
•
Lamp Power (Normal): Press eLeft orfRight on the projector or remote
control to set Normal or Economic as the power type of your projection.
Using Eco mode reduces system noise and reduces power consumption by
20%. If this mode is activated, the light output will be reduced and result in
darker projected images.
Setting the projector in Economic mode extends the lamp timer
automatic shutdown feature. For more information on how the total lamp
Lamp Settings
•
Lamp Hours:
i. Lamp Hours Nor.: Shows the total time of the lamp has been used in
normal mode.
ii. Lamp Hours Eco.: Shows the total time of the lamp has been used in
economic mode.
iii. Lamp Rest Rate: Shows the percentage of the rest lamp life.
•
Reset Lamp Timer: Resets the lamp timer. This should only be done after
Use the patterns when installing the projector, even if there is no input signal.
•
Grid: Press ENTER to display the grid test pattern. It helps you adjust the
image size and the focus to ensure that the projected image is free of
distortion.
Pattern
•
Color Bar: Press ENTER to display the color bar test pattern. After making
color adjustments, you can display this test pattern to check that the colors
are to your liking.
•
•
Dust Filter Hours: Shows the total time of the filter has been used.
Reset Dust Filter Timer: Reset the dust filter timer. This should only be
for details.
Dust Filter
This item is designed for those who use the projector in extreme environments, like
high temperature or high altitude. We recommend you select Yes when your
environment is higher than 3200 feet, or is hotter than 40°C. See "Operating in a
high altitude environment" on page 33 for details.
High Altitude
(Off)
•
Password (Off): Limits use of the projector to only those who know the
correct password. When the function is activated for the first time, you have
Once the password is set and this function is selected, the projector is
password-protected. Users who do not know the correct password can not
use the projector. The password can be entered by using either the buttons
on the projector or the remote control.
Password
•
Change Password: You will be asked to enter the current password before
Disables or enables all panel key functions except POWER on the projector and
buttons on the remote control. To release key lock, press and hold EXIT on the
control panel or remote control for 5 seconds.
Key Lock (Off)
Source Block
Sets whether one or more than one source to be skipped or searched when the
projector is detecting input signals. See "Speeding up the process of source search"
on page 26 for details.
40
Menus
Download from Www.Somanuals.com. All Manuals Search And Download.
Returns all settings to the factory preset values.
Reset All Settings
The following settings will still remain: Phase, Projector Position,
Language, Password and High Altitude Mode.
Information menu
FUNCTION (default
setting / value)
DESCRIPTION
Shows the current signal source.
Source
Shows the selected mode in the Picture--Basic menu.
Shows the resolution of the input signal.
Picture Mode
Resolution
Shows the total time of the lamp has been used in normal mode.
Shows the total time of the lamp has been used in economic mode.
Shows the percentage of the rest lamp life.
Lamp Hours Nor.
Lamp Hours Eco.
Lamp Rest Rate
Dust Filter Hour
Shows the total time of the filter has been used.
Menus
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you have to do on a regular basis is keep the lens clean
and clean or replace the air filter. Never remove any parts of the projector except the lamp or the air filter.
Contact your dealer or local BenQ Customer Service Centre if the projector fails to operate as expected.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. Before you attempt to clean the lens, turn the
projector off, unplug the power cable, and leave it several minutes to cool completely.
1. Use a canister of compressed air to remove dust. (Available from building hardware or photographic
suppliers.)
2. If there is stubborn dirt or smudge marks, use a proper photographic lens brush or moisten a clean soft lens
cloth with lens cleaner to gently wipe the lens surface.
Never touch the lens with your finger or rub the lens with abrasive materials. Even paper towels can
damage the lens coating. Only ever use a proper photographic lens brush, cloth, and cleaning solution. Do
not attempt to clean the lens whilst the projector is switched on or is still hot from previous use.
Storing the projector
If you need to store the projector for an extended time, please:
1. Make sure the temperature and humidity of the storage area are within the recommended range for the
projector. Please refer to the Spec. page in this manual or consult your dealer about the range.
2. Retract the adjuster feet.
3. Remove the batteries from the remote control.
4. Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. When you carry the
projector yourself, please use a soft carry case.
Cleaning and replacing the dust filter
It is necessary to clean the dust filter periodically every 1000 hours use. You can use the Advanced Setup > Dust
Filter > Dust Filter Hours menu or the Information menu to check how long the filter has been used. If the filter
is not cleaned, it can become clogged with dust and prevent proper ventilation. This can cause overheating and a
malfunction of the projector.
Should the projector filter become seriously clogged with dust,
it can cause over-heating inside of the projector. You will see
WARNING
FILTER CLEANING REMINDER NOTICE
the message pictured to the right before the projector shuts
down and powers off.
The projector filters require regular cleaning.
Please schedule time to check the filters and
clean if necessary (refer to User's Manual)
OK
42
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
To clean the filter:
1. Shut down the projector if turned on and wait
until the fans stop running.
2. Disconnect the projector from any cables.
3. Turn the projector over. Draw the dust filter grill
from the bottom side of the projector.
4. Use a small vacuum cleaner (designed for
computers and other office equipment) or use a
soft brush (such as a clean artist’s paintbrush) to
vacuum or sweep the dust away.
• If the dirt is difficult to remove or the filter is
broken, you should replace it.
5. Re-install the filter grill securely.
6. Reapply power and turn the projector on.
•
If the filter grill is not correctly seated in place, you will be reminded by a message displayed on the
screen every three minutes until ENTER on the projector or remote control is pressed.
Please check if the filter is well attached.
•
The projector will automatically shut down within one minute if there has been no further action
taken. Re-install the filter securely, then turn on the power again.
7. Reset the dust filter timer
i. Press MENU to open the OSD menu.
ii. Go to the Advanced Setup > Dust Filter menu and press ENTER.
iii. Highlight Reset Dust Filter Timer and press ENTER.
iv. A warning message displays asking if you want to reset the dust filter timer.
v. Highlight Reset and press ENTER to reset the
WARNING
filter timer to "0".
Reset Filter Timer?
Reset
Cancel
Maintenance
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp Information
Calculation of lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the
built-in timer. The method of calculating the equivalent lamp hour is as follows:
Total (equivalent) lamp hour
= 1 (hours used in Economic mode) +3/2 (hours used in normal mode)
The lamp hour in Economic mode is calculated as 2/3 of that in normal mode. That is, using the projector in
Economic mode helps to extend the lamp hour by 1/3.
Warning message
When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please
install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some
instances the lamp may explode.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the
power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning
the power back on, please contact your dealer.
The following Lamp warning displays will remind you to change the lamp.
Message
Status
WARNING
Total (equivalent) lamp hour has reached 2000 hours. Install a new
lamp for optimal performance.
NOTICE: Order replacement lamp
Lamp > 2000hrs
Projector will stop at 3000hrs
OK
WARNING
Total (equivalent) lamp hour has reached 2950 hour. A new lamp
should be fitted to avoid the inconvenience when the projector runs out
of lamp time.
NOTICE: Replace lamp soon
Lamp > 2950hrs
Projector will stop at 3000hrs
OK
Total (equivalent) lamp hour has reached 3000 hours. It is strongly
recommended that you replace the lamp at this age. The lamp is a
consumable item. With the usage time increase, the lamp brightness
diminished gradually. This is normal lamp behaviour. You can replace
the lamp whenever you notice that the brightness level has significantly
diminished. If the lamp is not replaced beforehand, it must be replaced
after 3000 hours usage
WARNING
NOTICE: Replace lamp now
Lamp > 3000hrs
Lamp-usage time exceeded
OK
44
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
If this warning message displays, the projector will shut down in 40
seconds. The lamp MUST be replaced before the projector will operate
normally.
WARNING
NOTICE: Lamp-usage time
exceeded
Replace lamp (refer to User's
Manual) then reset lamp timer
OK
Replacing the lamp
•
•
•
•
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord
before changing the lamp.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing
the lamp.
To reduce the risk of injuries to fingers and damage to internal components, use caution when
removing lamp glass that has shattered into sharp pieces.
To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do
not touch the empty lamp compartment when the lamp is removed.
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in
a proper manner.
1. Turn the power off and disconnect the projector from
the wall socket. Turn off all connected equipment and
disconnect all other cables.
2. Turn the projector over. Then loosen the screw on the
lamp cover.
3. Remove the lamp cover.
Do not turn the power on with the lamp cover removed.
4. Loosen the screws that hold the lamp to the projector. If
the screws are not loosened completely, they could
injure your fingers. It is strongly recommended that
you use a magnetic-head screwdriver to retain the screw
should it come loose.
Maintenance
45
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Lift the handle so that it stands up. Use the handle to
slowly pull the lamp out of the projector.
•
Pulling it too quickly may cause the lamp to break and
scatter broken glass in the projector. To reduce the
risk of injuries to fingers and damage to internal
components, use caution when removing lamp glass
that has shattered.
•
•
Do not place the lamp in locations where water might
splash on it, children can reach it, near or above heat
sources, or near flammable materials.
Do not insert your hand into the projector when the
lamp is removed. If you touch the optical components
inside, it could cause blurred images.
6. As shown in the figure, lower the new lamp first into the
connector on the projector and align the two holes on
the lamp with the locators on the projector.
7. Push the lamp downwards to ensure it is firmly secured
to the projector.
8. Tighten the screws securing the lamp box.
9. Re-install the lamp cover.
10. Tighten the screw on the lamp cover.
•
Please be careful to not over-tighten the screws.
•
Loose screws may cause a bad connection, which
could result in malfunction.
11. Turn the power on and reset the lamp time.
i. Press MENU to open the OSD menu.
ii. Go to the Advanced Setup > Lamp Settings menu and
press ENTER.
WARNING
Reset Lamp Timer?
Reset
Cancel
iii. Highlight Reset Lamp Timer and press ENTER.
iv. A warning message displays asking if you want to reset
the lamp timer.
v. Highlight Reset and press ENTER to reset the lamp timer to "0".
Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.
46
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Temperature information
When the Temperature warning light is on, it is warning you of the following possible problems:
1. The internal temperature is too high.
2. The fans are not working.
Turn the projector off and contact qualified service personnel for further help. For more detailed information,
Indicators
Illustration
•
•
Blank -: Light OFF
: Light flashing
•
•
O: Orange light
R: Red light
•
G: Green light
•
: Light ON
Light
Status & Description
Power Temp Lamp
Power events
The projector has just been connected to a power outlet.
Main power switch on
O
O
O
G
G
O
O
R
R
Stand-by mode.
-
-
Powering up.
-
-
-
-
Normal operation.
•
The projector needs 140 seconds to cool down as it was
abnormally shut down without the normal cooling down
process. Or
-
-
-
-
O
O
G
•
The projector needs to cool for 90 seconds after the
power is turned off.
The projector has shutdown automatically. If you try to re-
start the projector, it will shutdown again. Please contact
your dealer for assistance.
Lamp events
-
-
-
-
Lamp hour warning/Lamp hour error.
The projector has shutdown automatically. If you try to re-
start the projector, it will shutdown again. Please contact
your dealer for assistance.
O
R
R
1. The projector needs 90 seconds to cool down. Or
2. Please contact your dealer for assistance.
-
Maintenance
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Light
Status & Description
Power Temp Lamp
Thermal events
-
-
-
-
R
R
R
R
R
R
R
R
R
R
R
R
R
G
G
R
G
O
R
G
O
R
G
O
R
G
O
R
G
R
R
R
G
G
G
O
O
The projector has shutdown automatically. If you try to re-
start the projector, it will shutdown again. Please contact
your dealer for assistance.
O
-
-
48
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
THE PROJECTOR DOES NOT TURN ON.
Cause
Remedy
Plug the power cord into the AC inlet on the projector,
and plug the power cord into the power outlet. If the
power outlet has a switch, make sure that it is switched
on.
There is no power from the power cable.
Attempting to turn the projector on again during
the cooling process.
Wait until the cooling down process has completed.
NO PICTURE
Cause
Remedy
The video source is not turned on or connected Turn the video source on and check that the signal
correctly.
cable is connected correctly.
The projector is not correctly connected to the
input source device.
Check the connection.
The input signal has not been correctly
selected.
Select the correct input signal with the Source key on
the projector or remote control.
The lens cap is still attached to the lens.
Remove the lens cap.
BLURRED IMAGE
Cause
Remedy
The projection lens is not correctly focused.
Adjust the focus of the lens using the focus ring.
The projector and the screen are not aligned
properly.
Adjust the projection angle and direction as well as the
height of the unit if necessary.
The lens cap is still attached to the lens.
Remove the lens cap.
REMOTE CONTROL DOES NOT WORK
Cause
Remedy
The battery is out of power.
Replace the battery with a new one.
There is an obstacle between the remote
control and the projector.
Remove the obstacle.
You are too far away from the projector.
Stand within 6 meters (19.5 feet) of the projector.
THE PASSWORD IS INCORRECT
Cause
Remedy
You do not remember the password.
Troubleshooting
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Projector specifications
All specifications are subject to change without notice.
Optical
Projection system
Three-panels LCD system.
0.55" LCD (1280 x 720)
1.2x zoom
DMD chip
Lens
23.5" ~ 300"
140W
Projection screen size
Lamp
Electrical
Video Signal
Data Signal
NTSC / NTSC4.43 / PAL-B/G / PAL-M / PAL-N / SECAM / HDTV
XGA, SVGA, VGA, Macintosh®, HDTV (1080p, 1080i, 720p, 576p, 576i,
480p, 480i)
Max. number of display colors
16,770,000 (full color display)
Terminals
Input
Output
Video, S-Video, Component (Y/ CB/ CR, Y/ PB/ PR), D-sub, HDMI
12VDC (Max 0.5A)
General characteristics
Weight
8.8lbs/ 4.0kg+/-0.2
Power
VAC 100 - 240V, 4.0 A, 50 / 60 Hz (Automatic)
Max 215W
Power consumption
Operating temperature
Operating humidity
Operating altitude
0~35 C, (without condensation)at sea level
10% - 90% (without condensation)
0~1499m, 0~35°C
High altitude mode: 1500~3000m 0~30°C
-20°C- 60°C / -4°F to 140°F
10% - 90%
Storage temperature
Storage humidity
Dimensions
349 x 126.8 x 295.8 mm (W x H x D)
349
295.8
Center
126.8
of lens
77
77
Unit: mm
50
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Timing chart
'V' denotes the type of input that this timing can support.
Refresh
rate(Hz)
H. Freq.
(KHz)
PixelFreq.
(MHz)
Comp.
1/2
S-Video/
Video
Format
Resolution
D-Sub
HDMI
720 x 400
720 x 400
70
60
72
75
85
60
72
75
85
60
70
75
85
60
60
75
85
31.469
31.5
37.9
37.5
43.3
37.9
48.1
46.9
53.7
48.4
56.5
60
28.322
25.175
31.5
31.5
36
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
640 x 480
800 x 600
1024 x 768
1280 x 768
640 x 480
800 x 600
1024 x 768
1280 x 768
40
50
49.5
56.25
65
75
78.75
94.5
68.25
79.5
135
68.7
47.4
47.8
80
91.1
157.5
Specifications
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Refresh
rate(Hz)
H. Freq.
(KHz)
PixelFreq.
(MHz)
Comp.
1/2
S-Video/
Video
Format
Resolution
D-Sub
HDMI
59.94 /
60
15.734/
15.75
NTSC 3.58
-
3.58
-
V
-
-
59.94 /
60
15.734/
15.75
NTSC 4.43
PAL-B/G
PAL M
-
-
-
-
-
4.43
4.43
3.58
3.58
4.43
-
-
-
-
-
V
V
V
V
V
-
-
-
-
-
-
-
-
-
-
50
15.625
59.94 /
60
15.734/
15.75
PAL N
50
15.625
59.94 /
60
15.734/
15.75
PAL 60
59.94 /
60
15.734/
15.75
480/60i
480/60p
720 x 487
720 x 483
-
-
V
V
-
-
-
-
V
V
59.94 /
60
31.469/
31.5
576/50i
576/50p
720/50p
720 x 576
720 x 576
1280 x 720
50
50
50
15.625
31.25
37.5
14.75
29
V
V
V
-
-
-
-
-
-
V
V
V
75.25
59.94 /
60
44.955/
45
720/60p
1080/50i
1080/60i
1080/24p
1080/50p
1080/60p
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
74.25
V
V
V
V
V
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
28.125/
31.25
50
74.25/72
59.94 /
60
33.716/
33.75
74.175/
74.25
-
23.98 /
24
26.978/
27
74.175/
74.25
-
62.5/
56.25
50
148.5
V
-
59.94 /
60
67.433/
67.5
148.35/
148.5
52
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Copyright information
Copyright
Copyright © 2007 by BenQ Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes
from time to time in the contents hereof without obligation of BenQ Corporation to notify any person of
such revision or changes.
*Hollywood Quality Video and HQV are trademarks of Silicon Optix Inc. Others are copyrights of their
respective companies or organizations.
Warranty
BenQ warrants this product against any defects in material and workmanship, under normal usage and
storage.
Proof of purchase date will be required with any warranty claim. In the event this product is found to be
defective within the warranty period, BenQ’s only obligation and your exclusive remedy shall be
replacement of any defective parts (labor included). To obtain warranty service, immediately notify the
dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in accordance
with BenQ’s written instructions, especially the ambient humidity must be in-between 10% and 90%,
temperature in-between 0°C and 40°C, altitude lower than 10000 feet, and avoiding to operate the
projector in a dusty environment. This warranty gives you specific legal rights, and you may have other
rights which vary from country to country.
Warranty and Copyright information
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Regulation statements
FCC statement
CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the distance between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help.
EEC statement
This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electronic
Magnetic Compatibility) and fulfills these requirements.
MIC statement
B class equipment (Household purpose info/telecommunications equipment)
This equipment has undergone EMC registration for household purpose, and can be used in any area
including residential area.
WEEE directive
Disposal of Waste Electrical and Electronic Equipment by users in private households in the European
Union.
This symbol on the product or on the packaging indicates that this can not be disposed of
as household waste. You must dispose of your waste equipment by handling it over to the
applicable take-back scheme for the recycling of electrical and electronic equipment. For
more information about recycling of this equipment, please contact your city office, the
shop where you purchased the equipment or your household waste disposal service. The
recycling of materials will help to conserve natural resources and ensure that it is recycled
in a manner that protects human health and environment
54
Regulation statements
Download from Www.Somanuals.com. All Manuals Search And Download.
|