Dryer
DCY 9402 GXB1
User Manual
2960311037_EN/220115.1701
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Important instructions for safety and
environment
This section contains safety instructions that will help protect from risk of
personal injury or property damage. Failure to follow these instructions shall
void any warranty.
1.1 General safety
•The dryer can be used by children at and above 8 years old and by
persons whose physical, sensory or mental capabilities were not fully
developed or who lack experience and knowledge provided that they
are supervised or trained on the safe usage of the product and the risks
it brings out. Children should not play with the product. Cleaning and
maintenance works should not be performed by children unless they are
supervised by someone.
•Children of less than 3 years should be kept away unless continously
supervised.
•Adjustable feet should not be removed. The gap between the dryer and
the floor should not be reduced with materials such as carpet, wood and
tape. This will cause problems with the dryer.
•Always have the installation and repairing procedures carried out by the
Authorized Service. Manufacturer shall not be held liable for damages
that may arise from procedures carried out by unauthorized persons.
•Never wash the dryer by spraying or pouring water onto it! There is the
risk of electric shock!
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
3 / 28 EN
Important instructions for safety and environment
1.1.1 Electrical safety
A Electrical safety instructions should be followed while electrical
connection is made during the installation.
•Connect the dryer to a grounded outlet protected by a fuse at the value
specified on the type label. Have the grounding installation performed by
a qualified electrician. Our company shall not be liable for any damages
that will arise when the dryer is used without grounding in accordance
with the local regulations.
•The voltage and allowed fuse protection is stated on the type label plate.
•The voltage specified on the type label must be equal to your mains
voltage.
•Unplug the dryer when it is not in use.
•Unplug the dryer from the mains during installation, maintenance,
cleaning and repair works.
•Do not touch the plug with wet hands! Never unplug by pulling on the
cable, always pull out by grabbing the plug.
•Do not use extension cords, multi-plugs or adaptors to connect the dryer
to power supply in order to decrease the risk of fire and electric shock.
•Power cable plug must be easily accessible after installation.
B Damaged mains cable should be changed notifying the Authorized
B If the dryer is faulty, it must not be operated unless it is repaired
Service.
by an authorized service agent! There is the risk of electric shock!
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
4 / 28 EN
Important instructions for safety and environment
1.1.2 Product safety
Points to be taken into consideration for fire hazard:
Below specified laundry or items must not be dried
in the dryer considering fire hazard.
•Unwashed laundry items
•Items soiled with oil, acetone, alcohol, fuel oil, kerosene, stain
removers, turpentine, paraffin or paraffin removers must be
washed in hot water with plenty of detergent before being dried
in the dryer.
For this reason especially the items containing the above
specified
stains must be washed very well, to do this
use adequate detergent and choose a high washing
temperature.
Below specified laundry or items must not be dried in the
dryer due to the fire hazard:
•Garments or pillows bolstered with rubber foam (latex foam),
shower bonnets, water resistant textiles, materials with rubber
reinforcement and rubber foam pads.
•Clothing cleaned with industrial chemicals.
Items such as lighter, match, coins, metal parts, needle etc.
may damage the drum set or may lead to functional problems.
Therefore check all the laundry that you will load into your dryer.
Never stop your dryer before
the programme completes. If you must do this, remove all
laundry
quickly and lay them out to dissipate the heat.
Clothes that are washed inadequately may ignite on their own
and even may ignite after drying ends.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
5 / 28 EN
Important instructions for safety and environment
•You must provide enough ventilation in order to prevent gases exiting from
devices operating with other types of fuels including the naked flame from
accumulating in the room due to the back fire effect.
Underwear that contains metal reinforcements should not be
A
dried
in the dryer. Dryer may be damaged if metal reinforcements come
loose and break off during drying.
Use softeners and similar products in accordance with the
instructions of their manufacturers.
C
C
Always clean the lint filter before or after each loading. Never
operate the dryer without the lint filter installed.
•Never attempt to repair the dryer by yourself. Do not perform any repair
or replacement procedures on the product even if you know or have the
ability to perform the required procedure unless it is clearly suggested in
the operating instructions or the published service manual. Otherwise, you
will be putting your life and others’ lives in danger.
•There must not be a lockable, sliding or hinged door that may block
the opening of the loading door in the place where your dryer is to be
installed.
•Install your dryer at places suitable for home use. (Bathroom, closed
balcony, garage etc.)
•Make sure that pets do not enter the dryer. Check the inside of the dryer
before operating it.
•Do not lean on the loading door of your dryer when it is open, otherwise it
may fall over.
•The lint must not be allowed to accumulate around the tumble dryer
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
6 / 28 EN
Important instructions for safety and environment
1.2 Mounting over a washing machine
•A fixing device should be used between the two machines when installing
the dryer above a washing machine. The fitting device must be installed
by the authorized service agent.
•Total weight of the washing machine and the dryer -with full load- when
they are placed on top of each other reaches to approx. 180 kilograms.
Place the products on a solid floor that has sufficient load carrying
capacity!
Washing machine cannot be placed on the dryer. Pay attention
to the above warnings during the installation on your washing
A machine.
Installation Table for Washing Machine and Dryer
Washing Machine Depth
Dryer Depth
62cm 60 cm 54 cm 50 cm 49 cm 45 cm 40 cm
Can be
Can be
Can be
Can be
Can be
Can be Cannot be
54 cm
60 cm
installed installed installed installed installed installed installed
Can be
Can be
Can be
Can be
Can be Cannot be Cannot be
installed installed installed installed installed installed installed
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
7 / 28 EN
Important instructions for safety and environment
1.3 Intended use
•Dryer has been designed for domestic use. It is not suitable for
commercial use and it must not be used out of its intended use.
•Use the dryer only for drying laundry that are marked accordingly.
•The manufacturer waives any responsibility arisen from incorrect usage or
transportation.
•The service life of the dryer that you purchased is 10 years. During this
period, original spare parts will be available to operate the dryer properly.
1.4 Child safety
•Packaging materials are dangerous for the children. Keep packaging
materials away from children.
•Electrical products are dangerous for the children. Keep children away
from the product when it is operating. Do not let them tamper with the
dryer. Use the child-proof lock in order to prevent the children to tamper
with the dryer.
Child-proof lock is on the control panel. (See Child lock)
C
•Keep loading door closed even when the dryer is not in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
8 / 28 EN
Important instructions for safety and environment
1.5 Compliance with the WEEE regulation
and disposing of the waste product
This product complies with EU WEEE Directive (2012/19/EU). This
product bears a classification symbol for waste electrical and
electronic equipment (WEEE).
This product has been manufactured with high quality parts and
materials which can be reused and are suitable for recycling. Do
not dispose of the waste product with normal domestic and other
wastes at the end of its service life. Take it to the collection center for the
recycling of electrical and electronic equipment. Please consult your local
authorities to learn about these collection centers.
1.6 Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive
(2011/65/EU). It does not contain harmful and prohibited materials
specified in the Directive.
1.7 Package information
Packaging materials of the product are manufactured from recyclable
materials in accordance with our National Environment Regulations. Do
not dispose of the packaging materials together with the domestic or other
wastes. Take them to the packaging material collection points designated
by the local authorities.
Please visit the following website to get more information on the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
9 / 28 EN
Important instructions for safety and environment
1.8 Technical Specifications
EN
Height (Min. / Max.)
Width
Depth
84,6 cm / 86,6 cm*
59,5 cm
60,9 cm
9 kg**
Capacity (max.)
Net weight (plastic front door usage)
Net weight (glass front door usage)
Voltage
39 kg
41 kg
Rated power input
Model code
See type label***
* Min. height: Height with adjustable feet are closed.
Max. height: Height with adjustable feet are opened maximum.
** Dry laundry weight before washing.
*** Type label is located behind the loading door.
Technical specifications of the dryer are subject to specification
without notice to improve the quality of the product.
Figures in this manual are schematic and may not match the
product exactly.
Values stated on markers on the dryer or in the other published
documentation accompanying with the dryer are obtained in
laboratory in accordance with the relevant standards. Depending
on operational and environmental conditions of the dryer, these
values may vary.
C
C
C
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
10 / 28 EN
2 Your Dryer
2.1 Package Contents
1
2
3
4
5
1. Water drain hose *
2. Filter drawer spare sponge*
3. User Manual
4. Drying basket*
5. Drying basket user manual*
*It can be supplied with your machine depending on its model.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
11 / 28 EN
3 Installation
3.2 Removing the transportation
safety assembly
Before the calling the nearest Authorized Service for the
installation of the dryer, ensure that electrical installation
and water drain is appropriate referring to the user's
manual.(See 3.3 Connecting to the drain and 3.5
Electrical connection) If they are not suitable, contact
a qualified electrician and technician to make necessary
arrangements.
Remove the transportation safety
assembly before using the dryer for the
first time.
A
Open the loading door.
There is a nylon bag inside the drum that contains a
piece of styrofoam. Hold it from its section marked with
XX XX.
Preparation of the dryer's location
as well as the electrical and waste
water installations is under customer's
C
Pull the nylon towards yourself and remove the
transportation safety assembly.
responsibility.
Prior to installation, visually check if the
dryer has any defects on it. If the drier
A is damaged, do not have it installed.
Damaged products cause risks for your
safety.
3.1 Appropriate installation location
Install the dryer on a stable and level surface.
Dryer is heavy. Do not move it by yourself.
•
Operate your dryer in a well ventilated, dust-free
environment.
•
The gap between the dryer and the surface should
not be reduced by the materials such as carpet,
wood and tape.
Do not cover the ventilation grills of the dryer.
There must not be a lockable, sliding or hinged
door that may block the opening of the loading
door in the place where your dryer is to be
installed.
Once the dryer is installed, it should stay at the
same place where its connections have been
made. When installing the dryer, make sure that
its rear wall does not touch anywhere (tap, socket,
etc.).
Place the dryer at least 1 cm away from the edges
of other furniture.
Check that no part of the transportation
safety assembly remains inside the drum.
A
•
•
3.3 Connecting to the drain
In products equipped with condenser unit, water
accumulates in the water tank during the drying cycle.
You should drain accumulated water after each drying
cycle.
You can directly drain accumulated water through the
water drain hose supplied with the product instead of
periodically draining the water collected in the water
tank.
Please refer to the detailed instructions supplied with
the accessories pack.
•
•
•
Your dryer can be operated at temperatures
between +5°C and +35°C. If the operating
conditions fall outside of this range, operation of
the dryer will be adversely affected and it can get
damaged.
Connecting the water drain hose
1-2 Pull hose at the behind of the dryer by hand in
order to disconnect it from where it is connected.
Do not use any tools to remove the hose.
•
The rear surface of the tumble dryer shall be
placed against a wall.
3
Connect one end of the drain hose supplied with
the dryer to the connection point from where you
removed the hose of the product in previous step.
Do not place the dryer on the power
cable.
4
Connect the other end of the drain hose directly to
the wastewater drain or to the washbasin.
B
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
12 / 28 EN
Installation
3.5 Electrical connection
For specific instructions for electrical connection
required during installation (see 1.1.1 Electrical
Safety)
1
2
4
3.6 Transportation of the dryer
Unplug the dryer before transporting it.
Drain all water that has remained in the dryer.
If direct water drain connection is made, then remove
the hose connections.
3
We recommend carrying the dryer in
upright position. If it is not possible to
carry the machine in the upright position,
we recommend carrying it by tilting
A
towards the right side when looked from
the front.
Hose connection should be made in a safe
manner. Your drain house will be flooded if
the hose comes out of its housing during
water discharge.
3.7 Changing the illumination lamp
In case an illumination lamp is used in your laundry
dryer.To change the Bulb/LED used for illumination of
your tumble dryer, call your Authorized Service.
The lamp(s) used in this appliance is not suitable for
household room illumination. The intended purpose of
this lamp is to assist the user to place laundry in the
tumble dryer in a comfortable way.
A
Water drain hose should be attached to a
height of maximum 100 cm.
C
C
Make sure that the water drain hose is not
stepped on and it is not folded between the
drain and the machine.
3.4 Adjusting the feet
In order to ensure that the dryer operates more silently
and vibration-free, it must stand level and balanced on
its feet. Balance the machine by adjusting the feet.
Turn the feet to left or right until the dryer stands level
and firmly.
Never unscrew the adjustable feet from
their housings.
C
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
13 / 28 EN
4 Preparation
4.1 Laundry suitable for drying in the dryer
Always obey the instructions given on the garment tags. Dry only the laundry having a label stating that they are
suitable for drying in a dryer and make sure that you select the appropriate programme.
LAUNDRY DRYING SYMBOLS
Drying
Symbols
Suitable for
dryer
No Iron
Do not dry-
clean
Sensitive /
Delicate dry
Do not dry
with dryer
Do not dry
Drying
Settings
Iron -
Iron at high
temperature
Iron at medium
temperature
Iron at low
temperature
Dry or Steam
IRON
200 0C
150 0C
110 0C
Maximum temperature
4.2 Laundry not suitable for drying in 4.4 Things to be done for energy
the dryer
saving
Following information will help you use the dryer in an
ecological and energy-efficient manner.
Delicate embroidered fabrics, woolen, silk
garments, delicate and valuable fabrics,
airtight items and tulle curtains are not
suitable for machine drying.
•
Spin your laundry at the highest speed possible
when washing them. Thus, the drying time is
shortened and energy consumption is reduced.
Sort out the laundry depending on their type and
thickness. Dry the same type of laundry together.
For example thin kitchen towels and table clothes
dries earlier than thick bathroom towels.
Follow the instructions in the user manual for
programme selection.
C
•
4.3 Preparing laundry for drying
•
Laundry may be tangled with each other after
washing. Separate the laundry items before
placing them into the dryer.
•
•
•
•
Dry garments having metal accessories such as
zippers, inside out.
Fasten the zippers, hooks and buckles and button
sheets.
Do not open the loading door of the machine
during drying unless necessary. If you must
certainly open the loading door, do not to keep it
open for a long time.
•
•
•
Do not add wet laundry while the dryer is in
operation
Clean the lint filter before or after each drying
cycle. (See 6.1 in Maintenance and cleaning)
Clean the condenser regularly at least once every
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
14 / 28 EN
Preparation
month or after every 30 drying cycles. (See 6.4 in
Approximate weights
(g)*
Laundry
Maintenance and cleaning)
Ventilate the room, where the dryer is located, well
during drying.
•
Cotton quit covers (double)
Cotton quit covers (single)
Bed sheets (double)
Bed sheets (single)
Large tablecloths
Small tablecloths
Tea napkins
1500
1000
500
350
700
250
100
700
350
150
300
200
500
350
700
100
125
4.5 Correct load capacity
Follow the instructions in the “Programme selection and
consumption table”. Do not load more than the capacity
values stated in the table.
Bath towels
Hand towels
Blouses
Cotton shirts
Shirts
Cotton dresses
Dresses
Jeans
It is not recommended to load the dryer
with laundry exceeding the level indicated
Handkerchiefs (10 pieces)
T-Shirts
in the figure. Drying performance will
C
degrade when the machine is overloaded.
*Dry laundry weight before washing.
Furthermore, dryer and the laundry can get
damaged.
Following weights are given as examples.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
15 / 28 EN
5 Operating the product
5.1 Control panel
1
2
3
6
5
4
1. Program selection knob
2. Remaining duration indicator
3. On/Off button
4. Start/pause button
5. End duration button
6. Sound warning button
5.2 Screen symbols
Volume up
Tank Child-proof
Filter
cleaning
Mute
Anti
Creasing
full
lock
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
16 / 28 EN
Operating the product
5.3 Preparing the machine
5.5 Main programs
1. Plug in the machine
The main programs are given below based on fabric
type.
2. Place laundry inside the machine.
3. Press the On/Off button.
4. When your machine turns on for the first time,
it turns on with the declaration (cotton cabinet
dryness) program.
•
Cotton
Dry durable laundry with this program. It dries in normal
temperature. Recommended for use with your cotton
laundry (sheets, bed covers, towels, bathrobes etc.)
•
Synthetic
Pressing the On/Off button doesn‘t mean
the program starts.
C Press the Start / Pause button to start the
Dry laundry that is not very durable with this program.
Recommended for use with your synthetic laundry.
program.
5.6 Extra programs
5.4 Program selection
The following extra programs are available in the
machine for special conditions.
1. Determine the appropriate program from the chart
below containing the drying levels.
2. Select the program you desire using the Program
Selection knob.
Extra programs may vary according to the
specifications of your machine.
C
In order to receive better results from
drying machine programs, your laundry
C should be washed with the appropriate
program in your washing machine and
wringed with recommended wringing
revolution..
Only cotton laundry is dried in
normal temperature.
Thick and multi-layered laundry
(towels, sheets, jeans etc.) are dried
Extra Dry
so that they can be placed into
wardrobe without ironing.
•
Jeans
Use to dry jeans that are wringed with high rpm in
washing machine.
Normal laundry (tablecloths,
underwear etc.) are dried so that
they can be placed into wardrobe
Cupboard dry
•
Sport
Used to dry the laundry that are made of synthetic,
cotton or mixed fabrics and have a tag indicating that
they are suitable for drying.
without ironing.
Normal laundry (Ex: tablecloths,
underwear) are again dried so
that they can be placed into the
wardrobe but more so than the
wardrobe dryness option.
•
Shirts 15 min.
Dries shirts more delicately and thus causes less
wrinkles for easy ironing.
Cupboard
dry +
•
Baby Protect
Program used for baby clothing with can be dried
approval on the label.
Normal laundry (shirts, dresses
etc) are dried ready for ironing.
Very little dampness might remain
on the shirts after the program. It is
C recommended that you do not leave the
Iron Dry
shirts in the drying machine.
For detailed program information see.
„Program selection and consumption
C table“..
•
Delicates
You can dry your delicates suitable for drying or laundry
that is recommended to hand wash (silk blouses, thin
underwear etc.) in low temperature.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
17 / 28 EN
Operating the product
It is recommended to dry your delicates
in laundry bag to prevent wrinkles and
C damage. When the program ends,
take your laundry out of the machine
immediately and hang them to prevent
wrinkles.
•
Freshen up
It only performs ventilation for 10 minutes without
blowing hot air. You can ventilate the cotton and linen
clothing that has remained closed for a long duration
and remove their odor.
•
Timer programmes
You can select the 10 mins, 20 mins, 40 mins and 60
mins time programs to achieve the desired final drying
level with low temperature.
On this program, the machine dries as
long as the set duration, regardless of the
C drying level.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
18 / 28 EN
Operating the product
5.7 Program selection and consumption table
EN
Approximate
amount of
remaining humidity
Spin speed in washing
machine (rpm)
Drying time
(minutes)
Programs
Capacity (kg)
Cottons / Coloreds
Extra dry
9
9
9
1000
1000
1000
% 60
% 60
% 60
151
143
112
A
Cupboard dry
A
Iron dry
A
Shirts 15 min.
0.5
4
1200
1200
1000
600
% 60
%50
%60
%40
% 60
15
80
92
40
65
Jeans
Sport
4
Delicates
BabyProtect
Synthetics
2
3
1000
Cupboard dry
4.5
4.5
800
800
% 40
% 40
58
45
B
Iron dry
B
Energy consumption values
Approximate
amount of
remaining humidity
Energy
consumption value
kWh
Spin speed in washing
machine (rpm)
Programs
Capacity (kg)
Cottons linen Ready to wear*
Cottons Ready to iron
9
9
1000
1000
800
% 60
% 60
% 40
5,25
4,1
1,9
0,5
1,0
Synthetics Ready to wear
4.5
Power consumption of the off-mode for the standart cotton programme at full load, PO (W)
Power consumption of the left-on mode for the standart cotton programme at full load, PL (W)
„Cotton cupboard dry programme“ used at full and partial load is the standard drying programme
to which the information in the label and the fiche relates, that this programme is suitable for drying
normal wet cotton laundry and that it is the most efficient programme in terms of energy consumption
for cotton.
* : Energy Label standard program (EN 61121:2012)
All the values in the table are determined according to EN 61121:2012 standard. Consumption values may vary from
the values in the table depending on laundry type, wringing revolution, ambient conditions and changes in voltage.
CWhen selecting the Cottons programme, send the condensed water out through the drain hose.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
19 / 28 EN
Operating the product
Loading door open
5.8 Auxiliary functions
Start/Pause led blinks when the loading door of the
drying machine is open.
Sound warning cancel
Drying machine makes sound warnings when the
program is completed. If you don’t want sound
notifications, press the “Sound Notification” button.
When you press the sound notification button it lights
up, and program does not make sound notifications
when completed.
5.10 End duration
You can delay the end duration of the program for up to
24 hours with the end duration function.
1. Open the loading door and place your laundry.
2. Select the drying program.
3. Press the end duration selection button and set the
delay duration you want.
End duration led lights up. (End duration moves
continuously when you keep pressing the button).
4. Press the Start / Pause button. End duration
countdown begins. The “:” sign in the middle of
the displayed delay duration blinks.
You can select this function before or
after the program starts.
C
5.9 Warning symbols
Warning symbols may vary according to
the specifications of your machine.
C
You can add or remove laundry for the
duration of the end duration. The duration
C displayed on the screen is the sum of
the normal drying duration and the end
duration. At the end of the countdown the
end duration led turns off, drying beings
and drying led lights up.
Fiber filter cleaning
When the program is completed, a warning led lights
up, which indicates that the filter has to be cleaned.
Changing the end duration
If you want to change the duration during the
countdown:
1. Cancel the program by pressing the On/Off button.
Turn on the drying machine again by pressing the
On/Off button. When your drying machine turns on
for the first time, it turns on with the declaration
(cotton wardrobe dryness) program.
2. Select the program you desire using the Program
Selection knob.
3. Repeat the end duration operation for the duration
you want.
4. Start the program by pressing the Start / Pause
button.
Canceling the end duration function
If you want to cancel the end duration setting
countdown and start the program right away:
1. Cancel the program by pressing the On/Off button.
Turn on the drying machine again by pressing the
On/Off button. When your drying machine turns on
for the first time, it turns on with the declaration
(cotton wardrobe dryness) program.
If the filter cleaning led blinks, see the
„Troubleshooting“ chapter.
C
Water tank
When the program is completed, a warning led lights
up, which indicates that the water tank must be
emptied.
If the water tank fills up while the program is running,
warning led starts blinking and the machine goes into
stand-by. In that case empty the water in the water tank
and start the program by pressing the Start / Pause
button. Warning led turns off and the program resumes.
2. Select the program you desire using the Program
Selection knob.
3. Start the program by pressing the Start / Pause
button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
20 / 28 EN
Operating the product
Adding and removing laundry in stand-by mode
If you want to add or remove laundry after the drying
program starts:
1. Press the Start/Pause button to take the machine
into Stand-by mode. Drying operation stops.
2. Open the loading door, add or remove laundry and
close the loading door.
5.11 Starting the program
Start the program by pressing the Start / Pause button.
Start/Pause led and the Drying led light up, indicating
the program started. The “:” sign in the middle of the
remaining duration starts to blink.
5.12 Child Lock
3. Start the program by pressing the Start / Pause
button.
The machine features a child lock which prevents
the machine program flow from being affected when
buttons are pressed during operation.
The laundry adding made after the drying
operation started may cause the dried
C laundry inside the machine to mix with
the wet laundry and the laundry to remain
damp after the operation ends..
When the Child Lock is active, all buttons except for the
On/Off button are deactivated.
To activate the child lock, press the Sound Notification
button and End Duration button simultaneously for 3
seconds.
Laundry adding and removing can be
repeated as much as desired during
C drying operation.
But this process would continuously
interrupt the drying operation, and so
would cause the program duration
to lengthen and increase energy
Te child lock should be deactivated to be able to start
a new program after the current program ends or to
be able to interfere with the current program. Keep the
same buttons pressed for 3 seconds again to deactivate
the child lock.
consumption. Thus, it is recommended to
add laundry before the program starts.
If a new program is selected by changing
the position of the program selection knob
C while your machine is in stand-by mode,
the running program ends.
The lock led on the screen lights up when
the Child Lock is activated.
C
Do not contact the inner surface of the
drum when adding or removing laundry
during a continuing program. The drum
surface is hot.
Child Lock deactivates when the machine
is turned off and on again using the On/
C Off button.
A warning sound is heard when any button is pressed
(except for On/Off button) or the Program Selection knob
is turned while the child lock is active.
5.14 Canceling the program
If you want to cancel the program and end the drying
operation for any reason after the machine starts
running, press the On/Off button.
As it will be extremely hot inside the
machine when you cancel the program
A while the machine is in operation; run the
5.13 Changing the program after it is
started
After the machine starts running, you can change
the program you selected to dry your laundry with a
different program.
ventilation program to cool it down.
1. For example, to select Extra Dry program instead
of the Iron Dryness, stop the program by pressing
the Start / Pause button.
2. Turn the Program Selection knob to select the
Extra Dry program.
3. Start the program by pressing the Start / Pause
button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
21 / 28 EN
Operating the product
5.15 Program end
When the program ends, the Final/Wrinkle Prevention,
Fiber Filter Cleaning and Water Tank Warning leds on the
program follow up indicator light up. Loading door can
be opened and machine becomes ready for a second
run.
Press the On/Off button to turn off the machine.
In case the laundry is not removed after
the program is completed, the wrinkle
C prevention program that lasts 2 hours
start in order to prevent wrinkling of the
laundry that remains inside the machine.
Clean the fiber filter after each drying.
(See. „Fiber filter and loading door inner
C surface“)
Empty the water tank after each drying.
(See. „Emptying the water tank“)
C
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
22 / 28 EN
6 Maintenance and cleaning
Service life of product extends and frequently
experienced problems will be reduced if it is cleaned at
regular intervals.
6.1 Cleaning Lint Filter / Loading Door
Inner Surface
Lint and fiber released from the laundry to the air during
the drying cycle are collected in the Lint Filter.
•
Clean the entire inner surface of the loading door
and loading door gasket with a soft damp cloth.
Such fiber and lint are generally formed
during wearing and washing.
C
A
Always clean the lint filter and the inner
surfaces of the loading door after each
drying process.
You can clean the lint filter housing with a
vacuum cleaner.
C
To clean the lint filter:
•
•
Open the loading door.
Remove the lint filter by pulling it up and open the
lint filter.
•
•
Clean lint, fiber, and cotton raveling by hand or with
a soft piece of cloth.
Close the lint filter and place it back into its
housing.
6.2 Cleaning the sensor
There are dampness sensors in the dryer that detect
whether the laundry is dry or not.
To clean the sensors:
•
•
Open the loading doorof the dryer.
Allow the machine to cool down if it is still hot due
to the drying process.
•
Wipe the metal surfaces of the sensor with a soft
cloth, dampened with vinegar and dry them.
•
A layer can build up on the filter pores that can
cause clogging of the filter after using the dryer
for a while. Wash the lint filter with warm water
to remove the layer that builds up on the lint
filter surface. Dry the lint filter completely before
reinstalling it.
Clean metal surfaces of the sensors 4
times a year.
C
C
Do not use metal tools when cleaning
metal surfaces of the sensors.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
23 / 28 EN
Maintenance and cleaning
•
Drain the water in the tank.
Never use solvents, cleaning agents or
similar substances for cleaning due to the
risk of fire and explosion!
A
•
•
If there is lint accumulation in the funnel of the
water tank, clean it under running water.
Place the water tank into its seat.
If the direct water draining is used as
an option, there is no need to empty the
C
water tank.
6.3 Draining the water tank
Dampness of the laundry is removed and condensed
during drying process and the water that arise
accumulates in the water tank. Drain the water tank
after each drying cycle.
6.4 Cleaning the condenser;
Hot and humid air in the condenser is cooled with the
cold air from the room. Thus, the humid air circulating in
your dryer is condensed and then pumped into the tank.
Clean the condenser after every 30 drying
Condensed water is not drinkable!
cycles or once a month.
C
A
Never remove the water tank when the
program is running!
To clean the condenser:
1. If a drying process has been carried out, open the
door of the machine and wait until it cools down.
A
If you forget to drain the water tank, the machine will
stop during the subsequent drying cycles when the
water tank is full and the Water Tank warning symbol
will flash. If this is the case, drain the water tank and
press Start / Pause button to resume the drying cycle.
To drain the water tank:
Pull the drawer and remove the water tank carefully.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
24 / 28 EN
Maintenance and cleaning
2. Unlock the 2 condenser locks after opening the kick
plate.
5. Place the condenser in its housing. Fasten the 2 locks
and make sure that they are seated securely.
6. Close the kick plate cover.
3. Pull out the condenser.
4. Clean the condenser by applying pressurized water
with a shower armature and wait until the water
drains.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
25 / 28 EN
7 Troubleshooting
Drying process takes too much time.
Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.
Condenser may be clogged. >>> Clean the Condenser.
Ventilation grids on the front side of the machine are blocked. >>> Remove the objects (if any) that block
ventilation in front of the ventilation grids.
Ventilation may not be sufficient since the room where the machine is installed is very small. >>> Open the door
and window of the room to avoid the room temperature increase too much.
Lime deposit has built up on the dampness sensor. >>> Clean the dampness sensor.
Excessive laundry might have been loaded in. >>> Do not load the dryer in excess.
Laundry might not be spun sufficiently. >>> Spin your laundry at a higher speed in your washing machine.
Laundry comes out wet at the end of drying.
After drying, the hot clothes feel damper than their actual dampness level.
C
A programme suitable for the laundry type might have not been used.>>> Check the garment tag and select a
programme suitable for the fabric type or use the timer programmes additionally.
Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.
Condenser may be clogged. >>> Clean the Condenser.
Excessive laundry might have been loaded in. >>> Do not load the dryer in excess.
Laundry might not be spun sufficiently. >>> Spin your laundry at a higher speed in your washing machine.
Dryer does not switch on or the programme does not start. Dryer does not start when it is set.
It might have not been plugged in. >>> Make sure that the machine is plugged in.
The loading door is ajar. >>> Make sure that the loading door is closed securely.
Programme is not selected or the Start / Pause button is not pressed. >>> Make sure that the programme is
selected and the machine is not in Pause mode.
"Childproof lock" might have been activated. >>> Deactivate the Childproof Lock.
Programme is interrupted without any cause.
The loading door might not be closed securely. >>> Make sure that the loading door is closed securely.
A power failure might have occurred. >>> Press Start / Pause button to start the program.
Water tank may be full. >>> Drain the water tank.
Laundry has shrunk, become felted or deteriorated.
A programme suitable for the laundry type might have not been used. >>> Check the garment tag and select a
programme suitable for the fabric type.
Drum lighting does not turn on. (On models with lamp)
Dryer might not be switched on with the On / Off / Cancel button. >>> Make sure that the dryer is switched on.
Bulb may have blown. >>> Call Authorized Service Agent to have the lamp replaced.
Filter Cleaning warning symbol light is on.
Lint filter is not cleaned. >>> Clean the lint filter.
Lint Filter Cleaning symbol is flashing.
Filter housing is clogged with lints. >>> Clean the lint filter housing.
A deposit has built up on the lint filter pores that may cause clogging. >>> Wash the lint filter with warm water.
Condenser may be clogged. >>> Clean the Condenser.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
26 / 28 EN
Troubleshooting
Water leaks from the loading door
Lint has accumulated on the inner surfaces of the loading door and on the surfaces of the loading door gasket. >>>
Clean the inner surfaces of the loading door and the surfaces of the loading door gasket.
Loading door opens spontaneously.
The loading door might not be closed securely. >>> Push the loading door to close until you hear a locking sound.
Water Tank warning symbol is on/flashing.
Water tank may be full. >>> Drain the water tank.
Water draining hose might be bent. >>> If the product is connected directly to a wastewater drain, check the water
drain hose.
Condenser cleaning warning symbol is flashing.
Condenser might have not been cleaned. >>> Clean the Condenser.
CAUTION: If you cannot eliminate the problem although you follow the instructions in this section,
consult your dealer or the Authorized Service Agent. Never try to repair a nonfunctional product yourself.
A
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
27 / 28 EN
8 Electrical Connection
Make sure that you have an earthed power outlet
socket rated at 13 amps (minimum).
Important
Fitting a different plug
A
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals on
your plug, proceed as follows:
1 Connect the green - yellow or green (earth) wire
to the terminal in the plug marked ‘E’ or with the
symbol or coloured green and yellow or green.
2 Connect the blue (neutral) wire to the terminal in
the plug marked ‘N’ or coloured black.
Attention!
If you use your dryer as built-in, the socket must
be reachable after installation, or a separate
switch (which can disconnect the two poles) must
be used in the installation. Check for suitability.
For a permanent connection, a master switch with
at least 3mm contact clearance and minumum 13
A rating must be used.
Electrical requirements
3 Connect the brown (live) wire to the terminal in
the plug marked ‘L’ or coloured red.
Before you insert the plug into the wall socket
make sure that the voltage and the frequency
shown in the rating label corresponds to your
electricity supply.
With the alternative plugs a 13A fuse must be
fitted either in the plug or adaptor or in the main
fuse box. If in doubt contact a qualified electrician.
We recommend that this appliance be connected
to the mains supply via a suitable switched and
fused socket in a readily accessible position.
Should the mains lead of the appliance become
damaged or need replacing at any time, it must
be replaced by a special purpose made mains
lead which can only be obtained from a Authorised
Service Agent.
Green and yellow
or green
A Warning
This appliance must be earthed
N
L
Blue or black
Brown or red
If the fitted moulded plug is not suitable for your
socket, then the plug should be cut off and an
appropriate plug fitted.
The moulded plug on this appliance incorporates a
13A fuse. Should the fuse need to be replaced an
ASTA approved BS1362 fuse of the same rating
must be used. Do not forget to refit the fuse cover.
In the event of losing the fuse cover, the plug must
not be used until a replacement fuse cover has
been fitted. Colour of the replacement fuse cover
must be the same colour as that visible on the pin
face of the plug. Fuse covers are available from
any good electrical store.
In order to avoid hazards, damaged supply cord
should be replaced by the manufacturer, its service
agent or similarly qualified people.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer / User Manual
28 / 28 EN
|