BOXLIGHT Projector CP 300T User Manual

USER’S GUIDE  
BOXLIGHT CP-300t  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
All the safety and operating instructions should be read before  
the product is operated.  
This projector should be operated only from the type of power  
source indicated on the marking label. If you are not sure of  
the type of power supplied, consult your authorized dealer or  
local power company.  
Read all of the instructions given here and retain them for later  
use. Unplug this projector from AC power supply before  
cleaning. Do not use liquid or aerosol cleaners. Use a damp  
cloth for cleaning.  
Do not overload wall outlets and extension cords as this can  
result in fire or electric shock. Do not allow anything to rest on  
the power cord. Do not locate this projector where the cord  
may be damaged by persons walking on it.  
Follow all warnings and instructions marked on the projector.  
For added protection to the projector during a lightning storm,  
or when it is left unattended and unused for long periods of  
time, unplug it from the wall outlet. This will prevent damage  
due to lightning and power line surges.  
Do not attempt to service this projector yourself as opening or  
removing covers may expose you to dangerous voltage or  
other hazards. Refer all servicing to qualified service  
personnel.  
Unplug this projector from wall outlet and refer servicing to  
qualified service personnel under the following conditions:  
a. When the power cord or plug is damaged or frayed.  
b. If liquid has been spilled into the projector.  
Do not expose this unit to rain or use near water... for  
example, in a wet basement, near a swimming pool, etc...  
Do not use attachments not recommended by the  
manufacturer as they may cause hazards.  
c. If the projector has been exposed to rain or water.  
d. If the projector does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions as improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the projector to normal operation.  
e. If the projector has been dropped or the cabinet has been  
damaged.  
f. When the projector exhibits a distinct change in  
performance-this indicates a need for service.  
Do not place this projector on an unstable cart, stand, or table.  
The projector may fall, causing serious injury to a child or  
adult, and serious damage to the projector. Use only with a  
cart or stand recommended by the manufacturer, or sold with  
the projector. Wall or shelf mounting should follow the  
manufacturer's instructions, and should use a mounting kit  
approved by the manufacturers.  
An appliance and cart combination should  
be moved with care. Quick stops,  
excessive force, and uneven surfaces  
may cause the appliance and cart  
combination to overturn.  
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer that have the same characteristics as the  
original part. Unauthorized substitutions may result in fire,  
electric shock, or injury to persons.  
Upon completion of any service or repairs to this projector, ask  
the service technician to perform routine safety checks to  
determine that the projector is in safe operating condition.  
Slots and openings in the back and bottom of the cabinet are  
provided for ventilation, to insure reliable operation of the  
equipment and to protect it from overheating.  
The openings should never be covered with cloth or other  
materials, and the bottom opening should not be blocked by  
placing the projector on a bed, sofa, rug, or other similar  
surface. This projector should never be placed near or over a  
radiator or heat register.  
This projector should not be placed in a built-in installation  
such as a book case unless proper ventilation is provided.  
Voor de klanten in Nederland  
Bij dit product zijn batterijen  
geleverd.  
Wanneer deze leeg zijn,  
moet u ze niet weggooien  
maar inleveren als KCA.  
Never push objects of any kind into this projector through  
cabinet slots as they may touch dangerous voltage points or  
short out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the projector.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPLIANCES  
Federal Communication Commission Notice  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15  
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generated, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following measures :  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
AC POWER CORD REQUIREMENT  
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.  
AC Power Cord for the United States and Canada :  
AC Power Cord used in the United States and Canada is listed by the Underwriters  
Laboratories (UL) and certified by the Canadian Standard Association (CSA).  
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure  
that the plug will fit into the power outlet. Do not try to defeat this safety feature.  
Should you be unable to insert the plug into the outlet, contact your electrician.  
GROUND  
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
FEATURES AND DESIGN  
6
7
COMPUTER INPUT  
22  
SELECTING INPUT SOURCE  
22  
22  
23  
SELECTING COMPUTER SYSTEM  
PREPARATION  
COMPATIBLE COMPUTER SPECIFICATIONS  
PC ADJUSTMENT  
24  
24  
25  
AUTO PC ADJUSTMENT  
MANUAL PC ADJUSTMENT  
NAME OF EACH PART OF PROJECTOR  
7
8
8
9
9
SETTING-UP PROJECTOR  
CONNECTING AC POWER CORD  
POSITIONING PROJECTOR  
ADJUSTABLE FEET  
PICTURE IMAGE ADJUSTMENT  
IMAGE LEVEL SELECT  
27  
27  
28  
IMAGE LEVEL ADJUSTMENT  
MOVING PROJECTOR  
10  
PICTURE SCREEN ADJUSTMENT  
29  
VIDEO INPUT  
30  
CONNECTING PROJECTOR  
11  
SELECTING INPUT SOURCE  
SELECTING VIDEO SYSTEM  
PICTURE IMAGE ADJUSTMENT  
IMAGE LEVEL SELECT  
30  
31  
32  
32  
33  
TERMINALS OF PROJECTOR  
CONNECTING TO COMPUTER  
CONNECTING TO VIDEO EQUIPMENT  
11  
12  
13  
IMAGE LEVEL ADJUSTMENT  
PICTURE SCREEN ADJUSTMENT  
34  
BEFORE OPERATION  
14  
OPERATION OF REMOTE CONTROL  
LASER POINTER FUNCTION  
14  
14  
15  
SETTING  
35  
REMOTE CONTROL BATTERIES INSTALLATION  
SETTING MENU  
35  
TOP CONTROLS AND INDICATORS  
16  
OPERATING ON-SCREEN MENU  
HOW TO OPERATE ON-SCREEN MENU  
FLOW OF ON-SCREEN MENU OPERATION  
MENU BAR  
17  
17  
17  
18  
APPENDIX  
37  
OPERATING WIRELESS MOUSE  
37  
MAINTENANCE  
38  
38  
38  
38  
39  
39  
BASIC OPERATION  
19  
WARNING TEMP. INDICATOR  
AIR FILTER CARE AND CLEANING  
CLEANING PROJECTION LENS  
LAMP REPLACEMENT  
TURNING ON / OFF PROJECTOR  
ADJUSTING SCREEN  
ZOOM ADJUSTMENT  
19  
20  
20  
20  
20  
20  
21  
21  
LAMP REPLACE COUNTER  
TROUBLESHOOTING  
TECHNICAL SPECIFICATIONS  
40  
42  
FOCUS ADJUSTMENT  
KEYSTONE ADJUSTMENT  
PICTURE FREEZE FUNCTION  
NO SHOW FUNCTION  
P-TIMER FUNCTION  
SOUND ADJUSTMENT  
21  
TRADEMARKS  
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.  
IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.  
Windows and PowerPoint are registered trademarks of Microsoft Corporation.  
Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its  
respective corporation.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES AND DESIGN  
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This  
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)  
technology.  
Compact Design  
Digital Zoom (for Computer)  
This projector is extremely compact in size and weight.  
It is designed to carry and work anywhere you wish to  
use.  
Digital Zoom function adjusts the image size to approx.  
1/4 ~ 49 times of original image size, allowing you to  
focus on crucial information at a presentation.  
Compatibility  
Keystone Correction  
This projector widely accepts various video and  
computer input signals including;  
Positioning height of a projector may result in distorted  
image being displayed in a trapezoid shape. Keystone  
Correction solves this problem by digitally altering  
projection to produce undistorted images.  
Computers  
IBM-compatible or Macintosh computer up to 1280  
x 1024 resolution.  
6 Color Systems  
Power Management  
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-  
N color system can be connected.  
Power Management function is provided to reduce power  
consumption while a projector is not in use.  
Component Video  
This Power Management function operates to turn  
Projection Lamp off when a projector detects signal  
interruption and any button is not pressed over 5  
minutes. Projection Lamp is automatically turned on  
again when a projector detects signal or any operation  
button is pressed.  
Component video signal, such as a DVD player  
output high definition TV signals including 480i,  
480p, 575i, 575p, 720p, 1035i or 1080i, can be  
connected.  
S-Video  
S-Video signal, such as a S-VHS VCR output  
signal, can be connected.  
This projector is shipped with this function ON.  
Digital Visual Interface  
High Resolution Image  
This projector is equipped with DVI 24-pin terminal for  
connecting DVI output from a computer.  
This projector provides 1024 x 768 dots resolution for  
computer input and 800 horizontal TV lines. Resolution  
from a computer between XGA (1024 x 768) and SXGA  
(1280 x 1024) is compressed into 1024 x 768 dots. This  
projector cannot display image of over 1280 x 1024 dots.  
When resolution of your computer is over than 1280 x  
1024, reset a computer output for lower resolution.  
Laser Pointer Function  
Remote Control Unit supplied with this projector includes  
Laser Pointer function. This function helps you to make  
a smart presentation on a projected screen.  
Multi-Scan System  
Wireless Mouse  
This projector has Multi-Scan System to conform to  
almost all computer output signals quickly. There is no  
need for troublesome manual adjustment of frequency  
and other settings.  
Remote Control Unit supplied with this projector has  
Wireless Mouse function for a connected computer. This  
function enables you to operate both projector and  
computer with Remote Control Unit only.  
One-Touch Auto PC Adjustment  
Multilanguage Menu Display  
Incoming computer video signals are recognized and the  
best adjustment is automatically set by Auto PC  
Adjustment. No complicated setup is necessary and  
projection is always precise.  
Operation menu is displayed in; English, German,  
French, Italian, Spanish, Portuguese, Dutch, Swedish,  
Chinese, Korean or Japanese.  
Media Card Imager (Optional)  
Optional Media Card Imager is available for this  
projector. Contact the sales dealer where you  
purchased this projector for optional parts.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
NAME OF EACH PART OF PROJECTOR  
FRONT  
EXHAUST VENTS  
HOT AIR EXHAUSTED !  
Air blown from Exhaust Vents is hot.  
When using or installing projector,  
following precautions should be taken.  
Do not put any flammable object near  
these vents.  
Keep front grills at least 3(1m) away  
from any object, especially heat-  
sensitive object.  
Do not touch this area, especially screw  
and metallic part. This area will become  
hot while a projector is used.  
CARRY HANDLE  
This projector detects internal  
temperature and automatically controls  
operating power of Cooling Fans.  
INFRARED  
REMOTE RECEIVER  
LENS COVER  
PROJECTION LENS  
BACK  
TOP CONTROLS  
AND INDICATORS  
INFRARED  
REMOTE RECEIVER  
SPEAKER  
TERMINALS  
AND CONNECTORS  
POWER CORD CONNECTOR  
BOTTOM  
AIR FILTER  
AIR INTAKE VENTS  
(Back and Bottom)  
LAMP COVER  
This projector is equipped with Cooling  
Fans for protection from overheating.  
Pay attention to the following to ensure  
proper ventilation and avoid a possible  
risk of fire and malfunction.  
Do not cover vent slots.  
ADJUSTABLE FEET  
AND  
FEET LOCK LATCHES  
Keep back and bottom clear of any  
object. Obstructions may block  
cooling air.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
SETTING-UP PROJECTOR  
CONNECTING AC POWER CORD  
This projector uses nominal input voltages of 100-120 V or 200-240  
V AC. This projector automatically selects the correct input  
voltage. It is designed to work with single-phase power systems  
having a grounded neutral conductor. To reduce risk of electrical  
shock, do not plug into any other type of power system.  
Consult your authorized dealer or service station if you are not sure  
of the type of power supply being in use.  
Connect a projector with a peripheral equipment before turning a  
projector on. (Refer to pages 11 ~ 13 for connection.)  
CAUTION  
For safety, unplug AC Power Cord when an appliance is not  
used.  
When this projector is connected to the outlet with AC Power  
Cord, an appliance is in Stand-by Mode and consumes a little  
electric power.  
Connect AC Power Cord (supplied) to a projector.  
The AC outlet must be near this equipment and  
must be easily accessible.  
NOTE ON THE POWER CORD  
The AC Power Cord must meet the requirement of the country where you use the projector.  
Confirm the AC plug type with the chart below. The proper AC power cord must be used.  
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.  
Projector side  
AC Outlet side  
For the U.S.A. and Canada  
For Continental Europe  
Ground  
To the POWER CORD  
CONNECTOR on the  
projector.  
To the AC Outlet.  
(120 V AC)  
To the AC Outlet.  
(200 - 240 V AC)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
POSITIONING PROJECTOR  
This projector is designed to project on a flat projection surface.  
The projector can be focused from 5.3(1.6m) ~ 40.0(12.2m).  
Refer to the figure below to adjust a screen size.  
ROOM LIGHT  
The brightness in a room has a great influence on  
picture quality. It is recommended to limit  
ambient lighting in order to provide the best  
image.  
40.0(12.2m)  
300”  
26.6(8.1m)  
Max. Zoom  
20.0(6.1m)  
200”  
230”  
Min. Zoom  
13.1(4.0m)  
150”  
115”  
H1  
5.3(1.6m)  
153”  
100”  
77”  
40”  
31”  
H2  
31”  
40”  
100”  
150”  
200”  
300”  
Screen Size  
(W x H) mm  
629.9 x 472.4  
812.8 x 609.6  
2032 x 1524  
54(1371.6mm)  
6(152.4mm)  
3048 x 2286  
81(2057.4mm)  
9(228.6mm)  
4064 x 3048  
6096 x 4572  
16.7(425.16mm) 21.6(548.64mm)  
1.9(47.24mm) 2.4(60.96mm)  
108(2743.2mm) 162(4114.8mm)  
Height (H1)  
Height (H2)  
12(304.8mm)  
18(457.2mm)  
ADJUSTABLE FEET  
Picture tilt and projection angle can be adjusted by rotating  
ADJUSTABLE FEET. Projection angle can be adjusted to 15.6  
degrees.  
Lift the front of a projector and pull FEET LOCK LATCHES  
on the both sides of a projector.  
1
Release FEET LOCK LATCHES to lock ADJUSTABLE FEET  
and rotate ADJUSTABLE FEET to fine tune position and tilt.  
2
To retract ADJUSTABLE FEET, lift the front of a projector  
and pull and undo FEET LOCK LATCHES.  
Keystone distortion of a projected image can be adjusted by  
Menu Operation. (Refer to P20 and 35.)  
3
CAUTION  
FEET LOCK  
LATCHES  
ADJUSTABLE FEET  
Avoid positioning a projector with the angle of more than 20  
degrees. Projection Lamp may malfunction.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
MOVING PROJECTOR  
Use Carry Handle when moving a projector.  
When moving a projector, replace Lens Cover and retract  
Adjustable Feet to prevent damage to the lens and cabinet.  
When a projector is not in use for an extended period, put it into  
the case (carrying bag) supplied with a projector.  
CAUTION  
Carrying Bag (supplied) is intended for protection from dust and  
scratches on the surface of a cabinet, and it is not designed to  
protect an appliance from external forces. Do not transport a  
projector through a courier or transport services with this bag. The  
projector can be damaged. When handling a projector, do not  
drop, bump, subject it to strong forces or put other things on the  
cabinet.  
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR  
Do not drop or bump a projector, otherwise damages or malfunctions may result.  
When carrying a projector, use a suitable carrying case.  
Do not transport a projector by using a courier or transport service in an unsuitable transport case. This may cause  
damage to a projector. To transport a projector through a courier or transport service, consult Boxlight dealer for best  
way.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
TERMINALS OF PROJECTOR  
This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on  
pages 11 to 13 and connect properly.  
S-VIDEO INPUT JACK  
AUDIO INPUT JACKS  
VIDEO INPUT JACKS  
AUDIO OUTPUT JACKS  
Connect the S-VIDEO Connect the audio output Connect the composite video Connect an external  
output from video from video equipment to output from video equipment audio amplifier to these  
equipment to this these jacks.  
to VIDEO/Y jack or connect jacks.  
the component video outputs (Refer to P12, 13.)  
jack. (Refer to P12.)  
(Refer to P12.)  
When the audio output to VIDEO/Y, Pb/Cb and  
is monaural, connect it Pr/Cr jacks. (Refer to P12.)  
to L (MONO) jack.  
RESET BUTTON  
This projector uses a micro  
processor to control this unit,  
and occasionally, this micro  
processor may malfunction  
and need to be reset. This  
can be done by pressing  
RESET button with a pen,  
which will shut down and  
restart the unit. Do not use  
RESET function excessively.  
COMPUTER IN  
DIGITAL  
VIDEO  
(MONO)  
R – AUDIO IN – L  
S – VIDEO  
Y
Pb / Cb – Pr / Cr  
R – AUDIO OUT – L  
AUDIO IN  
COMPUTER  
RESET  
MCI  
COMPUTER IN  
ANALOG  
USB  
CONTROL PORT  
CONTROL PORT CONNECTOR  
When controlling the computer  
with Remote Control Unit of  
this projector, connect the  
mouse port of your personal  
computer to this connector.  
(Refer to P13.)  
COMPUTER INPUT  
TERMINALS (DIGITAL/ANALOG)  
COMPUTER AUDIO  
INPUT JACK  
USB CONNECTOR (Series B)  
When controlling the computer  
with Remote Control Unit of this  
projector, connect USB port of  
your personal computer to this  
connector. (Refer to P13.)  
Connect the computer Connect the audio output  
(digital/analog) output to (stereo) from computer to  
one of these terminals.  
(Refer to P13.)  
this jack. (Refer to P13.)  
Do not press this button. This button  
is used for our optional accessories.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
CONNECTING TO COMPUTER  
Cables used for connection (= Cable or adapter is not supplied with this projector.)  
VGA Cable (HDB 15 pin)  
USB Cable  
Control Cable for PS/2 Port  
DVI-Digital Cable (for Single Link T.M.D.S.) ●  
Control Cable for Serial Port , or ADB Port ●  
MAC Adapter (When connecting to Macintosh computer)  
Audio Cables (RCA x 2 and Mini Plug (stereo) x 1) ●  
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)  
Desktop type  
Laptop type  
Monitor Output  
Monitor Output Audio Output USB port Serial port PS/2 port  
ADB port  
MAC Adapter  
Set slide switches  
according to the  
chart below.  
Control Cable  
for Serial Port  
Control Cable  
for ADB Port ●  
Control Cable  
for PS/2 Port  
DVI  
Audio  
USB  
Cable  
Cable ●  
(stereo)  
Cable ●  
Terminal  
Terminal  
Terminal  
VGA Cable  
Use one of these Control  
Cables corresponding with  
the terminal of your  
computer.  
COMPUTER IN DIGITAL  
COMPUTER AUDIO IN  
USB  
COMPUTER IN  
VIDEO  
DIGITAL  
(MONO)  
R AUDIO IN L  
S VIDEO  
Y
Pb / Cb Pr / Cr  
R AUDIO OUT L  
CONTROL PORT  
COMPUTER IN ANALOG  
AUDIO IN  
COMPUTER  
RESET  
MCI  
COMPUTER IN  
ANALOG  
USB  
CONTROL PORT  
Terminals  
of the Projector  
AUDIO OUT  
NOTE :  
When connecting the cable, the power  
cords of both the projector and the external  
equipment should be disconnected from  
AC outlet. Turn the projector and  
peripheral equipment on before the  
computer is switched on.  
Audio Cable  
(stereo) ●  
MAC ADAPTER (Not supplied)  
Set switches as shown in the table  
below depending on RESOLU-  
TION MODE that you want to use  
before you turn on projector and  
computer.  
ON  
ON  
DIP  
Audio Input  
External Audio Equipment  
Audio Speaker  
1
2
3
4
5
6
OFF  
3
1
2
4
5
6
Audio Amplifier  
13" MODE (640 x 480)  
ON  
ON OFF OFF OFF OFF  
(stereo)  
16" MODE (832 x 624) OFF ON OFF ON OFF OFF  
19" MODE (1024 x 768) OFF ON  
21" MODE (1152 x 870) ON ON  
ON OFF OFF OFF  
ON ON OFF OFF  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
CONNECTING TO VIDEO EQUIPMENT  
Cables used for connection (= Cable is not supplied with this projector.)  
Video Cable (RCA x 1 or RCA x 3) ●  
S-VIDEO Cable ●  
Audio Cable (RCA x 2) ●  
Video Source (example)  
Component video output equipment.  
(such as DVD player or high-definition TV source.)  
Video Cassette Recorder  
Video Disc Player  
Composite  
Video Output  
Component Video Output  
(Y, Pb/Cb, Pr/Cr)  
Audio Output  
(R, L)  
S-VIDEO Output  
S-VIDEO  
Cable  
Video Cable  
(RCA x 1) ●  
Video Cable  
(RCA x 3) ●  
Audio Cable  
(RCA x 2) ●  
S-VIDEO  
Y - Pb/Cb - Cr/Pr  
AUDIO IN  
VIDEO  
COMPUTER IN  
DIGITAL  
VIDEO  
Y
(MONO)  
R AUDIO IN L  
Pb / Cb Pr / Cr  
AUDIO IN  
COMPUTER  
S VIDEO  
R AUDIO OUT L  
RESET  
Use any of VIDEO jack Y-Pb/Cb-  
Pr/Cr jacks or S-VIDEO jack.  
When both VIDEO jack and S-  
VIDEO jack are connected, S-  
VIDEO jack has priority over  
VIDEO jack.  
MCI  
COMPUTER IN  
ANALOG  
USB  
CONTROL PORT  
When both Y-Pb/Cb-Pr/Cr jacks  
and S-VIDEO jack are connected,  
Y-Pb/Cb-Pr/Cr jacks has priority  
over S-VIDEO jack.  
Terminals  
of the Projector  
AUDIO OUT  
Audio Cable  
(Stereo) ●  
Audio Input  
External Audio Equipment  
NOTE :  
When connecting the cable, the power  
cords of both the projector and the external  
equipment should be disconnected from  
AC outlet.  
Audio Speaker  
(stereo)  
Audio Amplifier  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
OPERATION OF REMOTE CONTROL  
Left Side  
LASER POINTER INDICATOR  
POWER ON-OFF BUTTON  
Used to turn projector on or  
off. (P19)  
Lights red while laser beam  
is emitted from Laser Light  
Window.  
ON-OFF  
ZOOM FOCUS  
VOLUME  
INPUT BUTTON  
Used to select input source.  
(P22, 30)  
D.ZOOM  
MUTE  
MENU  
INPUT  
MENU BUTTON  
POINT BUTTON  
Used to select MENU  
operation. (P17, 18)  
Used to move a pointer on ON-  
SCREEN MENU, adjust each  
item, or pan image in DIGITAL  
ZOOM +/mode. (P29)  
It is also used as a PC mouse  
in Wireless Mouse Operation.  
(P37)  
SELECT BUTTON  
Used to execute the item  
selected, or to expand or  
compress the image in  
DIGITAL ZOOM +/mode.  
(P29)  
It is also used as a PC  
mouse in Wireless Mouse  
Operation. (P37)  
When pressing the center of this  
button, it works as SELECT  
button.  
ALL-OFF SWITCH  
LASER  
When using Remote Control Unit,  
turn this switch to ON.And turn it  
to ALL OFFwhen it is not used.  
RIGHT CLICK BUTTON  
KEYSTONE  
Used as a PC mouse in  
Wireless Mouse Operation.  
(P37)  
NO SHOW  
FREEZE  
LASER BUTTON  
AUTO PC ADJ.  
P-TIMER  
IMAGE  
Used to operate Laser Pointer  
Function. Laser beam is  
emitted while pressing this  
button within 1 minute.  
When using this Laser Pointer  
for more than 1 minute, release  
LASER button and press it  
again.  
P-TIMER BUTTON  
Used to operate P-TIMER  
function. (P21)  
LASER POINTER FUNCTION  
This Remote Control Unit emits a laser beam as the laser pointer function from Laser Light Window. When LASER button is  
pressed, the laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is  
released, light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser  
beam is being emitted.  
The laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine the laser beam on yourself or  
other people. The three marks bellow are the caution labels for the laser beam.  
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result  
hazardous radiation exposure.  
These caution labels are put on the remote control.  
LASER POINTER INDICATOR  
Laser Light Window  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
Operating Range  
ON-OFF  
Point Remote Control Unit toward  
projector (Receiver Window)  
whenever pressing any button.  
Maximum operating range for  
Remote Control Unit is about 16.4’  
(5m) and 60° in front and rear of the  
projector.  
ZOOM BUTTON  
Used to adjust zoom.  
(P20)  
VOLUME BUTTON  
Used to adjust volume.  
(P21)  
ZOOM FOCUS  
VOLUME  
FOCUS BUTTON  
Used to adjust focus.  
(P20)  
D.ZOOM  
MUTE  
MENU  
INPUT  
D.ZOOM BUTTON  
Used to select DIGITAL  
ZOOM +/mode and  
resize image. (P29)  
MUTE BUTTON  
Used to mute sound.(P21)  
16.4’  
(5 m)  
60°  
LASER  
NO SHOW BUTTON  
Used to turn the picture  
into black image. (P21)  
FREEZE BUTTON  
Used to freeze the picture.  
(P21)  
KEYSTONE  
NO SHOW  
FREEZE  
IMAGE BUTTON  
Used to select image  
level. (P27, 32)  
AUTO PC ADJ.  
P-TIMER  
IMAGE  
AUTO PC ADJ. BUTTON  
Use to operate AUTO PC  
Adjustment function. (P24)  
60°  
16.4’  
(5 m)  
KEYSTONE BUTTON  
Used  
to  
correct  
keystone distortion.  
(P20, 35)  
Remote Control Batteries Installation  
Remove the battery  
compartment lid.  
Slide the batteries into  
the compartment.  
Replace the compartment  
lid.  
1
2
3
Two AA size batteries  
For correct polarity (+  
and ), be sure the  
battery terminals are in  
contact with the pins in  
the compartment.  
Press the lid down-  
ward and slide it.  
To insure safe operation, please observe the following precautions :  
Use (2) AA, UM3 or R06 type alkaline batteries.  
Replace two batteries at the same time.  
Do not use a new battery with an used battery.  
Avoid contact with water or liquid.  
Do not expose Remote Control Unit to moisture, or heat.  
Do not drop Remote Control Unit.  
If a battery has leaked on Remote Control Unit, carefully wipe the case clean and load new batteries.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
TOP CONTROLS AND INDICATORS  
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.  
POWER ONOFF BUTTON  
Used to turn the projector  
on or off. (P19)  
WARNING TEMP. INDICATOR  
READY INDICATOR  
Flashes red when  
internal  
temperature is too  
high. (P38)  
projector  
Lights green when the  
projector is ready to be  
ON--OFF  
turned on.  
And it  
flashes green in Power  
Management mode.  
(P36)  
LAMP REPLACE INDICATOR  
Turns to yellow when  
the life of the projection  
lamp draws to an end.  
(P39)  
LAMP INDICATOR  
Becomes dim when the  
projector is turned on.  
And bright when the  
projector is in stand-by  
mode.  
VOLUME –  
VOLUME +  
MENU BUTTON  
INPUT  
FOCUS  
IMAGE  
ZOOM  
Used to open or close  
MENU operation. (P17,  
18)  
MENU  
SELECT  
FOCUS BUTTON  
Used to adjust focus.  
(P20)  
INPUT BUTTON  
Used to select input  
source. (P22, 30)  
POINT (VOLUME + / ) BUTTONS  
SELECT BUTTON  
ZOOM BUTTON  
Used to select an item or adjust Used to execute the item Used to adjust zoom.  
value in ON-SCREEN MENU. They selected. It is also used (P20)  
are also used to pan the image in to expand / compress  
IMAGE BUTTON  
DIGITAL ZOOM +/mode. (P29)  
POINT LEFT/RIGHT buttons are ZOOM mode. (P29)  
also used as VOLUME +/buttons.  
the image in DIGITAL  
Used to select image  
level. (P27, 32)  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING ON-SCREEN MENU  
HOW TO OPERATE ON-SCREEN MENU  
You can control and adjust this projector through ON-SCREEN  
MENU. Refer to the following pages to operate each adjustment  
on ON-SCREEN MENU.  
WIRELESS REMOTE CONTROL  
POINT BUTTON  
Used to move the  
Pointer UP/ DOWN/  
RIGHT/ LEFT.  
1 DISPLAY MENU  
Press MENU button to display ON-SCREEN MENU.  
2 MOVING POINTER  
SELECT BUTTON  
Move the pointer (see below) or adjust the value of item by  
pressing POINT button(s) on Top Control or on Remote Control  
Unit.  
Used to select the item.  
TOP CONTROL  
Pointer is the icon on ON-SCREEN MENU to select the item.  
See the figures on the section "FLOW OF ON-SCREEN MENU  
OPERATION" below.  
POINT BUTTONS  
Used to move the  
Pointer UP/ DOWN/  
RIGHT/ LEFT.  
VOLUME –  
VOLUME +  
3 SELECT ITEM  
Select the item or set selected function by pressing SELECT  
button.  
SELECT  
MENU  
SELECT BUTTON  
Used to select the item.  
FLOW OF ON-SCREEN MENU OPERATION  
MENU BAR  
MENU ICON  
Display ON-SCREEN MENU  
Press MENU button to display ON-SCREEN MENU (MENU  
BAR). A red frame is POINTER.  
1
POINTER  
(red frame)  
POINTER (red frame)  
Press POINT DOWN button to  
move POINTER.  
Select Menu to be adjusted  
Move POINTER (red frame) to MENU ICON that you want to  
select by pressing POINT RIGHT / LEFT buttons.  
2
ITEM  
Control or adjust item through ON-SCREEN MENU  
Press POINT DOWN button and move POINTER (red frame  
or red arrow) to ITEM that you want to adjust, and then press  
SELECT button to show ITEM DATA.  
3
SELECT  
BUTTON  
Adjust ITEM DATA by pressing POINT RIGHT / LEFT  
buttons.  
Refer to the following pages for details of respective  
adjustments.  
4
ITEM DATA  
Press POINT LEFT/RIGHT  
buttons to adjust value or  
set function.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
MENU BAR  
FOR PC SOURCE  
Press MENU BUTTON while connecting to PC input source.  
IMAGE SELECT MENU  
SCREEN MENU  
SETTING MENU  
Used to select  
Used to adjust size  
of image. [Normal  
/ True / Wide /  
Digital zoom +/]  
(Refer to P29)  
Used to change  
settings of projector  
or reset Lamp  
Replace Counter.  
(Refer to P35, 36)  
GUIDE WINDOW  
PC SYSTEM MENU  
image level among  
Standard, Real  
and Image 1 ~ 4.  
(Refer to P27)  
Shows selected  
item of ON-  
SCREEN MENU.  
Used to select  
computer system.  
(Refer to P22, 23)  
INPUT MENU  
PC ADJUST MENU  
IMAGE ADJUST MENU  
SOUND MENU  
Used to select  
input source either  
Computer or  
Video.  
Used to adjust  
parameters to  
match with input  
signal format.  
Used to adjust  
Used to adjust  
volume or mute  
sound.  
computer image.  
[Contrast / Brightness  
/ White Balance  
(R/G/B) / Gamma]  
(Refer to P28)  
(Refer to P21)  
(Refer to P22)  
(Refer to P24-26)  
FOR VIDEO SOURCE  
Press MENU BUTTON while connecting to VIDEO input source.  
INPUT MENU  
Used to select  
input source  
either Video or  
Computer.  
IMAGE SELECT MENU  
SCREEN MENU  
Used to select image  
level among  
Standard, Cinema  
and Image 1 ~ 4.  
(Refer to P32)  
Used to set size of  
image to Normal  
or Wide.  
(Refer to P30)  
(Refer to P34)  
AV SYSTEM MENU  
IMAGE ADJUST MENU  
Same function as  
Menu for PC source.  
Same function as  
Menu for PC source.  
Used to select  
system of selected  
video source.  
Used to adjust picture image.  
[Contrast / Brightness / Color /  
Tint / White balance (R/G/B) /  
Sharpness / Gamma]  
(Refer to P31)  
(Refer to P33, 34)  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
TURNING ON / OFF PROJECTOR  
TURNING ON PROJECTOR  
Complete peripheral connections (with Computer, VCR, etc.)  
before turning on projector. (Refer to "CONNECTING TO  
PROJECTOR" on pages 11~13 for connecting that equipment.)  
1
2
Connect the projector's AC Power Cord into an AC outlet. LAMP  
Indicator lights RED, and READY Indicator lights GREEN.  
30  
NOTE : When On startfunction is ON, this projector is turned  
on automatically by connecting AC Power Cord to an  
AC outlet. (Refer to pages 35, 36.)  
Preparation Display disappears after 30 seconds.  
Press POWER ON-OFF button on Top Control or on Remote  
Control Unit to ON. LAMP Indicator dims, and Cooling Fans  
start to operate. Preparation Display appears on a screen and  
the count-down starts. The signal from PC or Video source  
appears after 30 seconds.  
3
TURNING OFF PROJECTOR  
Press POWER ON-OFF button on Top Control or on Remote  
Control Unit, and a message "Power off?" appears on a screen.  
1
2
Press POWER ON-OFF button again to turn off projector. LAMP  
Indicator lights bright and READY Indicator turns off. After  
projector is turned off, Cooling Fans operate (for 90 seconds).  
During this "Cooling Down" period, this appliance cannot be  
turned on.  
Power off?  
When projector has cooled down, READY Indicator lights  
GREEN again and you can turn projector on. After cooling down  
completely, disconnect AC Power Cord.  
Message disappears after 4 seconds.  
3
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN  
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE  
TURNING IT OFF.  
When Power Managementfunction is ON, projector detects signal interruption and turns off Projection Lamp automatically.  
Refer to Power Managementon pages 35 and 36.  
When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on  
projector again.  
When WARNING TEMP. Indicator continues to flash, follow procedures below:  
1. Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet.  
2. Check Air Filters for dust accumulation.  
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.)  
4. Turn a projector on again.  
If WARNING TEMP. Indicator should still continue to flash, call Boxlight at 1-800-762-5757 or 360-779-7901.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
ADJUSTING SCREEN  
ZOOM ADJUSTMENT  
Press ZOOM button on Top Control or ZOOM /button on  
Remote Control Unit. The message Zoomis displayed.  
1
2
Press ZOOM button or POINT UP button to make image  
larger, and press ZOOM button or POINT DOWN button to  
make image smaller.  
Zoom  
Message disappears after 4 seconds.  
FOCUS ADJUSTMENT  
Press FOCUS button on Top Control or FOCUS /button on  
Remote Control Unit. The message Focusis displayed.  
1
2
Adjust focus of image by pressing FOCUS /button or  
POINT UP/DOWN button(s) .  
Focus  
Message disappears after 4 seconds.  
KEYSTONE ADJUSTMENT  
If a projected picture has keystone distortion, correct image with KEYSTONE adjustment.  
Press KEYSTONE /button on Remote Control Unit or select  
Keystone on SETTING menu. (Refer to page 35.) Keystone  
dialog box appears.  
1
Correct keystone distortion by pressing KEYSTONE /button  
or POINT UP/DOWN button(s). Press KEYSTONE button or  
POINT UP button to reduce the upper part of image, and press  
KEYSTONE button or POINT DOWN button to reduce the  
lower part.  
2
Reduce the upper width with KEY STONE button  
or POINT UP button.  
Reduce the lower width with KEY STONE button  
or POINT DOWN button.  
PICTURE FREEZE FUNCTION  
Press FREEZE button on Remote Control Unit to freeze the picture  
on-screen. To cancel FREEZE function, press FREEZE button again  
or press any other button.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
NO SHOW FUNCTION  
Press NO SHOW button on Remote Control Unit to black out the  
image. To restore to normal, press NO SHOW button again or press  
any other button.  
No show  
Message disappears after 4 seconds.  
P-TIMER FUNCTION  
Press P-TIMER button on Remote Control unit. The timer display 00  
: 00appears on the screen and the timer starts to count time (00 : 00  
~ 59 : 59).  
To stop P-TIMER display, press P-TIMER button. And then, press P-  
TIMER button again to cancel P-TIMER function.  
SOUND ADJUSTMENT  
Indicates roughly level of  
volume.  
DIRECT OPERATION  
Volume  
Press VOLUME (+/) button(s) on Top Control or on Remote Control  
Unit to adjust volume. Volume dialog box appears on the screen for a  
few seconds.  
(+) button to increase volume, and () button for decreasing.  
Mute  
Press MUTE button to set  
Mute function On or Off.  
Press MUTE button on Remote Control Unit to cut off sound. To  
restore sound to its previous level, press MUTE button again or press  
Volume (+/) button(s).  
The display disappears after 4 seconds.  
MENU OPERATION  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to  
SOUND Menu icon.  
SOUND MENU  
1
Press POINT DOWN button to move a red frame pointer to the  
item that you want to select, and then press SELECT button.  
SOUND Menu icon  
2
Indicates roughly  
level of volume.  
Volume  
To increase volume, press POINT RIGHT button, and press POINT  
LEFT button for decreasing.  
Close SOUND Menu.  
Mute  
Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box  
display is changed to Onand sound is cut off. To restore sound to  
its previous level, press POINT LEFT/RIGHT button(s) again.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
SELECTING INPUT SOURCE  
INPUT button  
Computer  
DIRECT OPERATION  
Choose Computer by pressing INPUT button on Top Control or on  
Remote Control Unit.  
Video  
If projector cannot reproduce proper image, select correct input source  
through MENU OPERATION (see below).  
MENU OPERATION  
INPUT MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
1
POINT LEFT/RIGHT button to move a red frame pointer to  
INPUT Menu icon.  
INPUT Menu icon  
Press POINT DOWN button to move a red arrow pointer to  
2
Computer and then press SELECT button. Source Select Menu  
will appear.  
Move a pointer (red arrow)  
to Computer and press  
SELECT button.  
Move a pointer to either RGB (Digital) or RGB (Analog) and then  
press SELECT button.  
Computer  
3
Source Select Menu  
When your computer is connected to COMPUTER  
INPUT (DIGITAL) terminal, select RGB (Digital).  
RGB (Digital)  
Move a pointer to RGB  
(Digital) or RGB (Analog)  
and press SELECT button.  
When your computer is connected to COMPUTER  
INPUT (ANALOG) terminal, select RGB (Analog).  
RGB (Analog)  
SELECTING COMPUTER SYSTEM  
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to  
COMPATIBLE COMPUTER SPECIFICATIONon page 23). When selecting Computer, this projector automatically tunes  
to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)  
Note : Projector may display one of the following messages.  
When projector cannot recognize connected signal as PC  
system provided in this projector, Auto PC Adjustment  
function operates to adjust projector and the message  
Autois displayed on SYSTEM Menu icon. (Refer to  
P24.) When image is not provided properly, manual  
adjustment is required. (Refer to P25 and 26.)  
PC SYSTEM MENU  
Auto  
SYSTEM Menu icon  
Displays system being  
selected.  
There is no signal input from computer. Make sure the  
connection of computer and a projector is set correctly.  
(Refer to TROUBLESHOOTING on page 40.)  
––––  
SELECT COMPUTER SYSTEM MANUALLY  
This projector automatically selects PC system among those provided  
in this projector and PC system can be also selected manually.  
PC SYSTEM MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to PC  
SYSTEM Menu icon.  
1
SYSTEM Menu icon  
Displays system being selected.  
Press POINT DOWN button to move a red arrow pointer to the  
The systems on this dialog box  
can be selected.  
2
system that you want to set, and then press  
SELECT button.  
Custom Mode (1~5) set in PC  
ADJUST Menu. (P25, 26)  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
COMPATIBLE COMPUTER SPECIFICATIONS  
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140  
MHz of Dot Clock.  
ON-SCREEN  
DISPLAY  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
VGA 1  
VGA 2  
640 x 480  
720 x 400  
640 x 400  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
31.47  
31.47  
31.47  
37.86  
37.86  
37.50  
43.269  
34.97  
35.00  
15.625  
15.734  
35.156  
37.88  
46.875  
53.674  
48.08  
37.90  
34.50  
38.00  
38.60  
32.70  
38.00  
49.72  
48.36  
68.677  
60.023  
56.476  
60.31  
48.50  
44.00  
63.48  
36.00  
59.88  
70.09  
70.09  
74.38  
72.81  
75.00  
85.00  
66.60  
66.67  
XGA 10  
XGA 11  
XGA 12  
XGA 13  
XGA 14  
XGA 15  
MAC 19  
MAC 21  
SXGA 1  
SXGA 2  
SXGA 3  
SXGA 4  
SXGA 5  
SXGA 6  
SXGA 7  
SXGA 8  
SXGA 9  
SXGA 10  
SXGA 11  
SXGA 12  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 870  
1152 x 864  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 960  
1152 x 900  
1152 x 900  
62.04  
61.00  
35.522  
46.90  
47.00  
58.03  
60.24  
68.68  
64.20  
62.50  
63.90  
63.34  
63.74  
71.69  
81.13  
63.98  
79.976  
60.00  
61.20  
71.40  
50.00  
50.00  
63.37  
76.97  
61.85  
46.43  
63.79  
75.00  
80.00  
45.00  
33.75  
33.75  
77.07  
75.70  
86.96  
VGA 3  
(Interlace)  
VGA 4  
58.20  
58.30  
72.00  
75.08  
75.06  
70.40  
58.60  
60.00  
59.98  
60.01  
67.19  
76.107  
60.02  
75.025  
60.00  
65.20  
75.60  
VGA 5  
VGA 6  
VGA 7  
MAC LC13  
MAC 13  
RGB  
640 x 480  
––––––––  
50  
(Interlace)  
60  
––––––––  
RGB  
(Interlace)  
SVGA 1  
SVGA 2  
SVGA 3  
SVGA 4  
SVGA 5  
SVGA 6  
SVGA 7  
SVGA 8  
SVGA 9  
SVGA 10  
SVGA 11  
MAC 16  
XGA 1  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
56.25  
60.32  
75.00  
85.06  
72.19  
61.03  
55.38  
60.51  
60.31  
51.09  
60.51  
74.55  
60.00  
84.997  
75.03  
70.07  
74.92  
60.02  
54.58  
79.35  
86.00  
(Interlace)  
94.00  
(Interlace)  
SXGA 13 1280 x 1024  
SXGA 14 1280 x 1024  
SXGA 15 1280 x 1024  
SXGA 16 1280 x 1024  
60.01  
72.00  
66.00  
XGA 2  
SXGA 17  
1152 x 900  
86.70  
XGA 3  
SXGA 18 1280 x 1024  
SXGA 19 1280 x 1024  
(Interlace)  
XGA 4  
60.18  
75.08  
75.08  
60.00  
60.00  
(Interlace)  
60.00  
(Interlace)  
XGA 5  
MAC  
1280 x 960  
XGA 6  
MAC  
1280 x 1024  
––––––––  
XGA 7  
720p (HDTV)  
1035i (HDTV)  
1080i (HDTV)  
––––––––  
––––––––  
XGA 8  
87.17  
(Interlace)  
XGA 9  
When the input signal is from the COMPUTER INPUT DIGITAL terminal, refer to the chart below.  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
D-VGA  
D-SVGA  
D-XGA  
640 x 480  
800 x 600  
1024 x 768  
31.469  
37.879  
48.363  
59.940  
60.317  
60.004  
D-SXGA1 1280 x 1024  
D-SXGA2 1280 x 1024  
D-SXGA3 1280 x 1024  
63.981  
60.276  
31.65  
60.020  
58.069  
29.8  
(Interlace)  
NOTE : Specifications are subject to change without notice.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PC ADJUSTMENT  
AUTO PC ADJUSTMENT  
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your  
computer. Auto PC Adjustment function can be operated as follows.  
Auto PC Adj.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to PC  
ADJUST Menu icon.  
PC ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to  
AUTO PC Adj. icon and then press SELECT button twice.  
This Auto PC Adjustment can be also executed by pressing  
AUTO PC ADJ. button on Remote Control Unit.  
PC ADJUST Menu icon  
Move a red frame pointer to AUTO PC  
Adj. icon and press SELECT button.  
Store adjustment parameters.  
Adjustment parameters from Auto PC Adjustment can be memorized  
in this projector. Once parameters are memorized, setting can be  
done just by selecting Mode in PC SYSTEM Menu (P22). Refer to  
step 3 of MANUAL PC ADJUSTMENT section (P26).  
NOTE  
Fine sync, Total dots and Picture Position of some computers can  
not be fully adjusted with this Auto PC Adjustment function. When  
the image is not provided properly through this function, manual  
adjustments are required. (Refer to page 25, 26.)  
Auto PC Adjustment function cannot be operated when RGB,”  
720p (HDTV),” “1035i (HDTV)or 1080i (HDTV)is selected on PC  
SYSTEM Menu (P22).  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
MANUAL PC ADJUSTMENT  
This projector can automatically tune to the display signals from most personal computers currently distributed. However,  
some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-  
Scan system of this projector. If this happens, projector cannot reproduce a proper image and the image may be recognized  
as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.  
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special  
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This  
enables you to recall the setting for a specific computer whenever you use it.  
Note : This PC ADJUST Menu cannot be operated when the input signal is from COMPUTER IN DIGITAL terminal or RGB”  
is selected on PC SYSTEM MENU (P22).  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to PC  
ADJUST Menu icon.  
PC ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
item that you want to adjust and then press SELECT button.  
Adjustment dialog box will appear. Press POINT LEFT/RIGHT  
button to adjust value.  
PC ADJUST Menu icon  
Move a red frame icon to the item and  
press SELECT button.  
Fine sync  
Adjusts an image as necessary to eliminate flicker from the display.  
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)  
Shows status  
(Stored / Free) of the  
selected Mode.  
Total dots  
Selected Mode  
The number of total dots in one horizontal period. Press POINT  
LEFT/RIGHT button(s) and adjust number to match your PC image.  
Horizontal  
Adjusts horizontal picture position. Press POINT LEFT/RIGHT  
button(s) to adjust the position.  
Press POINT LEFT/RIGHT  
button to adjust the value.  
Vertical  
Adjusts vertical picture position. Press POINT LEFT/RIGHT  
button(s) to adjust the position.  
Press SELECT button at this icon to  
adjust Clamp,” “Display area (H/V)or  
set Full screen.”  
Current mode  
Press SELECT button to show the information of computer selected.  
Clamp  
Current mode  
Adjusts clamp level. When the image has a dark bar(s), try this  
adjustment.  
Press SELECT button at  
Current mode icon to show  
the information of computer  
connected.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
Display area  
Selects area displayed with this projector. Select the resolution at  
Display area dialog box.  
Press SELECT button at  
Display area icon and Display  
area dialog box appears.  
Display area H  
Adjustment of horizontal area displayed with this projector. Press  
POINT LEFT/RIGHT button(s) to decrease/increase value and then  
press SELECT button.  
Display area  
Display area V  
Adjustment of vertical area displayed with this projector. Press  
POINT LEFT/RIGHT button(s) to decrease/increase value and then  
press SELECT button.  
Press POINT LEFT  
/RIGHT button(s) to  
adjust value and then  
press SELECT button.  
Full screen  
Press POINT LEFT/RIGHT button(s) to switch Full screen function to  
Onor Off.Set Onto resize the image with 4 x 3 aspect ratio to  
fit the screen.  
NOTE : Fine sync, Total dots, Display area (H/V) and Full screen  
cannot be adjusted when 1035i (HDTV)or 1080i (HDTV)”  
is selected on PC SYSTEM Menu (P22).  
To store adjustment data.  
This Mode has parameters being stored.  
Store  
3
To store adjustment parameters, move a red frame pointer to  
Store icon and then press SELECT button. Move a red arrow  
pointer to any of Mode 1 to 5 that you want to store to and then  
press SELECT button.  
Mode free  
To clear adjustment parameters previously set, move a red  
frame pointer to Mode free icon and then SELECT button. Move  
a red arrow pointer to the Mode that you want to clear and then  
press SELECT button.  
Vacant Mode  
Store icon  
Shows values of Total dots,”  
Horizontal,” “Vertical,” “Display  
area H,and Display area V.”  
Other icons operates as follows.  
Reset  
Reset all adjust parameters on adjustment dialog box to previous  
figure.  
To clear adjustment data.  
Quit  
Closes PC ADJUST MENU.  
Close this dialog box.  
Mode free icon  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PICTURE IMAGE ADJUSTMENTS  
IMAGE LEVEL SELECT (DIRECT)  
Select image level among Standard, Real, Image 1, Image 2, Image 3  
IMAGE button  
and Image 4 by pressing IMAGE button on Top Control or on Remote  
Control Unit.  
Standard  
Real  
Standard  
Normal picture level preset on this projector.  
Image 1  
Image 2  
Image 3  
Image 4  
Real  
Picture level with improved halftone for graphics.  
IMAGE 1~4  
User preset picture adjustment in IMAGE ADJUST Menu (P28).  
IMAGE LEVEL SELECT (MENU)  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
IMAGE SELECT Menu icon.  
IMAGE SELECT MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
level that you want to set and then press SELECT button.  
IMAGE SELECT  
Menu icon  
Standard  
Normal picture level preset on this projector.  
Move a red frame pointer to the level  
and press SELECT button.  
Real  
Picture level with improved halftone for graphics.  
IMAGE 1~4  
The level being selected.  
User preset picture adjustment in IMAGE ADJUST Menu (P28).  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
IMAGE LEVEL ADJUSTMENT  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to  
IMAGE ADJUST Menu icon.  
IMAGE ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
item that you want to adjust. and then press SELECT button.  
The level of each item is displayed. Adjust each level by  
pressing POINT LEFT/RIGHT button(s).  
IMAGE ADJUST  
Menu icon  
Move a red frame pointer to  
the item to be selected and  
then press SELECT button.  
Contrast  
Press POINT LEFT button to decrease contrast, and POINT RIGHT  
button to increase contrast. (From 0 to 63.)  
Brightness  
Press POINT LEFT button to adjust image darker, and POINT  
RIGHT button to adjust brighter. (From 0 to 63.)  
Selected Image level  
White balance (Red)  
Press POINT LEFT button to lighten red tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
White balance (Green)  
Press POINT LEFT/RIGHT buttons  
to adjust value.  
Press POINT LEFT button to lighten green tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
White balance (Blue)  
Press POINT LEFT button to lighten blue tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
Store icon  
Press SELECT button at this icon to  
store the adjustment.  
Gamma  
Press either POINT LEFT button or POINT RIGHT button to obtain  
better balance of contrast. (From 0 to 15.)  
Store  
3
To store manually preset image, move a red frame pointer to  
Store icon and press SELECT button. Image Level Menu will  
appear. Move a red frame pointer to the Image 1 to 4 where you  
want to set and then press SELECT button.  
Image Level Menu  
Other icons operates as follows.  
Move a red frame pointer to any  
of Image 1 to 4 where you want  
to set and then press SELECT  
button.  
Reset  
Reset all adjustment to previous figure.  
Quit  
Closes IMAGE MENU.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen resize function, which enables you to display the desirable image size.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red frame pointer to  
SCREEN Menu icon.  
SCREEN MENU  
1
2
Press POINT DOWN button and move a red frame pointer to the  
function that you want to select and then press SELECT button.  
SCREEN Menu icon  
Move the red frame to the function and  
press SELECT button.  
Normal  
Provides image to fit screen size.  
True  
Provides image in its original size. When the original image size is  
larger than screen size (1024 x 768), this projector enters Digital  
zoom +mode automatically.  
NOTE  
This SCREEN Menu cannot be operated when  
1035i (HDTV)or 1080i (HDTV)is selected on  
PC SYSTEM Menu (P22).  
Wide  
Wide cannot be selected when 720p (HDTV)is  
Provides image to fit wide video aspect ratio (16 : 9) by expanding  
image width uniformly. This function can be used for providing a  
squeezed video signal at 16 : 9.  
selected on PC SYSTEM Menu (P22).  
True and Digital zoom +/cannot be selected  
when RGBis selected on PC SYSTEM Menu  
(P22).  
Digital zoom +  
This projector cannot display any resolution higher  
than 1280 X 1024. If your computers screen  
resolution is higher than 1280 X 1024, reset the  
resolution to the lower before connecting projector.  
When Digital zoom + is selected, ON-SCREEN MENU disappears  
and the message D. Zoom +is displayed. Press SELECT button to  
expand image size. And press POINT UP/DOWN/LEFT/RIGHT  
button(s) to pan the image. Panning function can work only when  
the image is larger than screen size.  
A projected image can be also expanded by pressing D.ZOOM ●  
button on Remote Control Unit.  
The image data in other than XGA (1024 x 768) is  
modified to fit the screen size in initial mode.  
Panning function may not operate properly if the  
computer system prepared on PC ADJUST Menu  
is used.  
Digital Zoom –  
When Digital zoom is selected, ON-SCREEN MENU disappears  
and the message D. Zoom –” is displayed. Press SELECT button to  
compress image size.  
A projected image can be also compressed by pressing D.ZOOM ●  
button on Remote Control Unit.  
To cancel Digital Zoom +/mode, press any button except D.ZOOM  
/, SELECT, POINT and LASER buttons.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
SELECTING INPUT SOURCE  
INPUT button  
Video  
DIRECT OPERATION  
Choose Video by pressing INPUT button on Top Control or on Remote  
Control Unit.  
Computer  
If projector cannot reproduce proper video source, select correct input  
source through MENU OPERATION (see below).  
MENU OPERATION  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
INPUT Menu icon.  
INPUT MENU  
1
Press POINT DOWN button to move a red arrow pointer to  
Video and then press SELECT button. Source Select Menu will  
appear.  
2
Move a pointer to Video and  
press SELECT button.  
Move a pointer to the source that you want to select and then  
press SELECT button.  
3
VIDEO  
Projector automatically detects incoming Video signal,  
and adjusts itself to optimize its performance.  
Auto  
When both VIDEO jack and S-VIDEO jack are  
connected, S-VIDEO jack has priority over VIDEO jack.  
When both Y-Pb/Cb-Pr/Cr jacks and S-VIDEO jack are  
connected, Y-Pb/Cb-Pr/Cr jacks have priority over S-  
VIDEO jack.  
Source Select Menu (VIDEO)  
Move a pointer to the source and press SELECT button.  
When video input signal is connected to VIDEO jack,  
select Video.  
Video  
When video input signal is connected to S-VIDEO jack,  
select S-Video.  
S-Video  
When video input signal is connected to Y-Pb/Cb-  
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.  
Y,Pb/Cb,Pr/Cr  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
SELECTING VIDEO SYSTEM  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to AV  
SYSTEM Menu icon.  
1
2
Press POINT DOWN button to move a red arrow pointer to the  
system that you want to select and then press SELECT button.  
VIDEO JACK OR S-VIDEO JACK  
AV SYSTEM MENU (VIDEO OR S-VIDEO)  
Auto  
Projector automatically detects incoming Video system, and adjusts  
itself to optimize its performance.  
When Video System is PAL-M or PAL-N, select system manually.  
AV SYSTEM Menu icon  
This box indicates the system  
being selected.  
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N  
If projector cannot reproduce proper video image, it is necessary to  
select a specific broadcast signal format among PAL, SECAM, NTSC,  
NTSC 4.43, PAL-M, and PAL-N.  
Move the pointer to the  
system and press  
SELECT button.  
Y, Pb/Cb, Pr/Cr JACKS  
AV SYSTEM MENU (COMPONENT VIDEO)  
Auto  
Projector automatically detects incoming Video signal, and adjusts  
itself to optimize its performance.  
COMPONENT VIDEO SIGNAL FORMAT  
AV SYSTEM Menu icon  
This box indicates the system  
being selected.  
If projector cannot reproduce proper video image, it is necessary to  
select a specific component video signal format among 480i, 575i,  
480p, 575p, 720p, 1035i and 1080i.  
Move the pointer to the  
system and press  
SELECT button.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
PICTURE IMAGE ADJUSTMENTS  
IMAGE LEVEL SELECT (DIRECT)  
Select image level among Standard, Cinema, Image 1, Image 2,  
Image 3 and Image 4 by pressing IMAGE button on Top Control or on  
Remote Control Unit.  
IMAGE button  
Standard  
Cinema  
Image 1  
Image 2  
Image 3  
Image 4  
Standard  
Normal picture level preset on this projector.  
Cinema  
Picture level adjusted for the picture with fine tone.  
IMAGE 1~4  
User preset picture adjustment in IMAGE ADJUST Menu (P34).  
IMAGE LEVEL SELECT (MENU)  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
IMAGE SELECT Menu icon.  
IMAGE SELECT MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
level that you want to set and then press SELECT button.  
IMAGE SELECT  
Menu icon  
Standard  
Normal picture level preset on this projector.  
Cinema  
Move the red frame pointer to the  
level and press SELECT button.  
Picture level adjusted for the picture with fine tone.  
IMAGE 1~4  
The level being selected.  
User preset picture adjustment in IMAGE ADJUST Menu (P34).  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
IMAGE LEVEL ADJUSTMENT  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red frame pointer to  
IMAGE ADJUST Menu icon.  
IMAGE ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
item that you want to adjust and then press SELECT button.  
The level of each item is displayed. Adjust each level by  
pressing POINT LEFT/RIGHT button(s).  
IMAGE ADJUST  
Menu icon  
Move a red frame pointer to  
the item to be selected and  
then press SELECT button.  
Contrast  
Press POINT LEFT button to decrease contrast, and POINT RIGHT  
button to increase contrast. (From 0 to 63.)  
Brightness  
Press POINT LEFT button to adjust image darker, and POINT  
RIGHT button to adjust brighter. (From 0 to 63.)  
Color  
Press POINT LEFT button to lighten color, and POINT RIGHT button  
to deeper color. (From 0 to 63.)  
Press POINT LEFT/RIGHT buttons  
to adjust value.  
Tint  
Press SELECT button at this icon to  
display other items.  
Press POINT LEFT button or POINT RIGHT button to obtain proper  
color. (From 0 to 63.)  
White balance (Red)  
Press POINT LEFT button to lighten red tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
Press SELECT button at this icon to  
display previous items.  
White balance (Green)  
Press POINT LEFT button to lighten green tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
Press POINT LEFT/RIGHT buttons  
to adjust value.  
White balance (Blue)  
Press POINT LEFT button to lighten blue tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
Sharpness  
Press POINT LEFT button to soften the image, and POINT RIGHT  
button to sharpen the image. (From 0 to 31.)  
Press SELECT button at this icon to  
store the value.  
Gamma  
Press either POINT LEFT button or POINT RIGHT button to obtain  
better balance of contrast. (From 0 to 15.)  
NOTE : Tint cannot be adjusted when the video system is PAL,  
SECAM, PAL-M or PAL-N.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
Store  
3
To store the adjustment data, move a red frame pointer to Store  
icon and press SELECT button. Image Level Menu will appear.  
Move a red frame pointer to the Image Level 1 to 4 and then  
press SELECT button.  
Image Level Menu  
Move a red frame pointer to  
the image icon to be set  
and then press SELECT  
button.  
Other icons operates as follows.  
Reset  
Reset all adjustment to previous figure.  
Quit  
Store icon  
Closes IMAGE MENU.  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen resize function, which enables you to display the desirable image size.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red frame pointer to  
SCREEN Menu icon.  
SCREEN MENU  
1
2
Press POINT DOWN button and move a red frame pointer to the  
function that you want to select and then press SELECT button.  
SCREEN Menu icon  
Move the red frame to the function and  
Normal  
press SELECT button.  
Provides image at a normal video aspect ratio of 4 : 3.  
NOTE : SCREEN Menu cannot be operated when  
720p,” “1035i,or 1080iis selected on AV  
SYSTEM Menu (P30).  
Wide  
Provides image at a wide screen ratio of 16 : 9.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
SETTING MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red-frame pointer to  
SETTING icon.  
SETTING MENU  
1
2
Press POINT DOWN button to move a red-frame pointer to the  
Set a red frame  
SETTING Menu icon  
item that you want to set and then press  
SELECT button.  
pointer to the item  
and press SELECT  
button.  
Setting dialog box appears.  
Language  
Language used in ON-SCREEN MENU is selectable from among  
English, German, French, Italian, Spanish, Portuguese, Dutch,  
Swedish, Chinese, Korean and Japanese.  
Keystone  
When the image is distorted vertically, select Keystone. ON-  
SCREEN MENU disappears and Keystone dialog box is displayed.  
Correct keystone distortion by pressing POINT UP/DOWN button(s).  
Refer to KEYSTONE ADJUSTMENT on page 20.  
When pressing SELECT  
button at Language,  
Language Menu appears.  
Blue back  
When this function is On,this projector will produce a blue image  
instead of the video noise on the screen when any input source is  
unplugged or turned off.  
Display  
This function decides whether to display On-Screen Displays.  
On ··· shows all the On-Screen Displays.  
Off ···· sets On-Screen Displays disappeared except;  
ON-SCREEN MENU  
Power off?message  
Logo  
Move a pointer to the item  
and then press POINT  
LEFT/RIGHT button(s).  
When this function is On,projector displays our logo when starting  
up.  
Ceiling  
Ceiling function  
When this function is On,picture is top / bottom and left / right  
reversed. This function is used to project the image from a ceiling  
mounted projector.  
Rear  
When this function is On,picture is left / right reversed. This  
function is used to project the image to a rear projection screen.  
Rear function  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
Power management  
This function turns Projection Lamp off when this projector detects  
signal interruption and is not used for a certain period in order to  
reduce power consumption and maintain the Lamp-life. (This  
projector is shipped with this function ON.)  
Time left until Lamp off.  
Power Management function operates to turn Projection Lamp off  
when the input signal is interrupted and any button is not pressed  
over 5 minutes. This function operates as follows;  
1. When any input signal is interrupted, No signaland the  
counting down display appears (for 5 minutes).  
2. When Projection Lamp turned off, READY Indicator turns off.  
Cooling Fans operate and Projection Lamp is turned off for 90  
seconds. (During this "Cooling Down" period, projector cannot  
be turned on.)  
3. When Projection Lamp has cooled down, READY Indicator  
flashes and Projection Lamp can be turned on again (Power  
Management mode).  
In this Power Management mode, Projection Lamp is  
automatically turned on when the input signal connected or  
projector is operated with any button on Top Control or on  
Remote Control Unit again.  
Press SELECT button at this icon to  
display other items.  
On start  
When this function is On,projector is automatically turned on just  
by connecting AC Power cord to a wall outlet.  
Press SELECT button at this icon to  
display previous items.  
Note ; Be sure to turn projector off properly (refer to the section  
TURNING OFF THE PROJECTORon P19). If projector is  
turned off in the wrong steps, On Start function does not  
operate properly.  
Move the pointer to the item and  
then press POINT LEFT/RIGHT  
button(s).  
Remote control  
This projector has two different remote control codes; the factory-set  
normal code (Code 1) and the secondary code (Code 2). This  
switching function prevents remote control operation mixture (jam)  
when operating several projectors or video equipment together.  
When operating projector in Code 2,both projector and Remote  
Control Unit must be switched to Code 2.”  
To change the code of Projector;  
Set Remote control in the SETTING MENU to Code 2.”  
To change the code of the Remote Control Unit;  
Press both MENU and IMAGE buttons on Remote Control Unit  
together for over 10 seconds.  
After changing the code, make sure Remote Control operates  
properly.  
To return to the normal code (Code 1), operate both projector and  
Remote Control in the ways above again.  
NOTE : When batteries of Remote Control Unit are replaced or ALL-  
OFF switch is turned to ALL-OFF,the remote transmit  
code automatically returns to the normal code (Code 1).  
Move the pointer to Lamp counter reset and then press  
SELECT button. The message Lamp replace counter  
reset?is displayed.  
Lamp counter reset  
This function is used to reset Lamp Replace Counter. When  
replacing Projection Lamp, reset Lamp Replace Counter by using  
this function. Refer to page 39 for operation.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
OPERATING WIRELESS MOUSE  
Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most  
Personal Computers. POINT buttons and two CLICK buttons are used for wireless mouse operation.  
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen. When ON-  
SCREEN MENU or any message / dialog box is displayed on the screen instead of PC mouse pointer, this Wireless Mouse  
function cannot be used.  
INSTALLATION  
To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of the mouse driver (not  
supplied) is required. Make sure that the mouse driver is properly installed in your computer. And make sure that the mouse  
port (or USB port) of a Personal Computer is activated.  
Connect the mouse port (or USB port) of your computer to  
Control Port (or USB connector) of this projector with Control  
Cable (or USB cable). (Refer to page 11, 12 for connection.)  
Note : When your computer has no mouse  
1
port, connect Serial Port of your  
computer to Control Port of the  
projector with Control Cable for Serial  
Port (not supplied).  
Turn the projector on first, and then turn on your computer.  
When the computer is switched on first, Wireless Mouse may not  
work properly.  
2
OPERATING WIRELESS MOUSE  
When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK  
button on Wireless Remote Control Unit.  
POINT button (Move the pointer)  
POINT button  
Used to move PC mouse pointer. The pointer is moved  
corresponding with the direction you are pressing.  
SELECT (LEFT CLICK) button  
This button has the same function as the left button in a PC mouse.  
RIGHT CLICK button  
This button has the same function as the right button in a PC mouse.  
This button is not available for controlling this projector.  
SELECT button  
(left button of the  
mouse)  
RIGHT CLICK button  
(right button of the mouse)  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
MAINTENANCE  
WARNING TEMP. INDICATOR  
WARNING TEMP. Indicator flashes red when an internal temperature of a projector exceeds the normal temperature. This  
Indicator stops flashing when the temperature of a projector returns to normal.  
When WARNING TEMP. Indicator continues to flash, check the items listed below.  
Ventilation Slots of the projector may be blocked. In such an event, reposition the projector so that Ventilation Slots  
are not obstructed.  
1
Air Filter may be clogged with dust particles. Clean Air Filter by following the section AIR FILTER CARE AND  
CLEANING below.  
2
If WARNING TEMP. Indicator remains on after performing the above checks, Cooling Fans or the Internal Circuits may  
be malfunctioning. In that case, call Boxlight.  
3
AIR FILTER CARE AND CLEANING  
Removable Air Filter prevents dust from accumulating on the surface of Projection Lens and Projection Mirror. Should Air  
Filter become clogged with dust particles, it will reduce Cooling Fanseffectiveness and may result in internal heat build up  
and adversely affect the life of the projector. Clean Air Filter following the steps below:  
Turn off the projector, and disconnect AC power cord from the  
AC outlet.  
1
Turn the projector upside down and remove Air Filter by pulling  
the latches upward.  
2
Clean Air Filter with a brush or wash out dust and particles.  
3
4
Replace Air Filter properly. Make sure that Air Filter is fully  
inserted.  
CAUTION  
Do not operate the projector with Air Filter removed. Dust  
may accumulate on LCD Panel and Projection Mirror  
degrading picture quality.  
Do not put small parts into Air Intake Vents. It may result in  
AIR FILTER  
Pull up and remove.  
malfunction of the projector.  
RECOMMENDATION  
We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments  
may cause poor image quality.  
When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements  
inside the projector. This condition may degrade the quality of a projected image.  
When the above symptoms are noticed, contact Boxlight at 1-800-762-5757 or 360-779-7901 for cleaning.  
CLEANING PROJECTION LENS  
Follow these steps to clean Projection Lens:  
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.  
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.  
1
Lightly wipe a cleaning cloth over Projection Lens.  
2
3
When the projector is not in use, replace Lens Cover.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
LAMP REPLACEMENT  
When the life of Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow. When a  
projected image becomes dark or the color of an image becomes unnatural, replacement of Projection Lamp is required.  
CAUTION  
CAUTION  
For continued safety, replace with a lamp  
assembly of the same type.  
Allow a projector to cool for at least 45  
minutes before you open Lamp Cover. The  
inside of a projector can become very hot.  
Do not drop a lamp assembly or touch a glass  
bulb! The glass can shatter and may cause  
injury.  
Follow these steps to replace the lamp assembly.  
LAMP COVER  
Turn off the projector and disconnect AC plug. Allow the  
1
projector to cool for at least 45 minutes.  
Remove a screw with a screwdriver to remove Lamp Cover.  
2
3
Remove 3 screws with a screwdriver and pull out Lamp  
Assembly by grasping Handle.  
Replace Lamp Assembly with a new one and tighten 3 screws  
back. Make sure that Lamp Assembly is set properly. Replace  
Lamp Cover and tighten a screw.  
4
LAMP  
HANDLE  
ASSEMBLY  
Connect AC Power Cord to the projector and turn it on.  
5
6
Reset Lamp Replace Counter (refer to the section Lamp  
Replace Counterbelow).  
NOTE : Do not reset Lamp Replace Counter when Projection  
Lamp is not replaced.  
ORDER REPLACEMENT LAMP  
Replacement Lamp can be ordered through Boxlight at 1-800-762-5757 or 360-779-7901.  
Model No. of your projector : BOXLIGHT CP-300t  
Replacement Lamp Type No. : POA-LMP35  
(Service Parts No. 610 293 2751)  
LAMP REPLACE COUNTER  
Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP  
REPLACE Indicator stops lighting.  
Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to  
move a red frame pointer to SETTING Menu icon (refer to page 35, 36).  
1
Press POINT DOWN button to move a red frame pointer to Lamp counter resetand then press  
message "Lamp replace counter reset?" is displayed. Move the pointer to [Yes] and then press SELECT button.  
SELECT button. The  
2
Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.  
3
Do not reset Lamp Replace Counter except after Projection Lamp is replaced.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TROUBLESHOOTING  
Before calling your dealer or service center for assistance, check the matters below once again.  
1. Make sure you have connected a projector to your computer or video equipment as described in the section  
"CONNECTING THE PROJECTOR" on pages 11 ~ 13.  
2. Check cable connection. Verify that all computer, video and power cord are properly connected.  
3. Verify that all power is switched on.  
4. If a projector still does not produce an image, re-start your computer.  
5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display. The  
problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to  
turn the computer and monitor off before you power up the projector. Power the equipment back on in order of : Projector  
and computer.)  
6. If the problem still exists, check following chart.  
Problem:  
No power.  
Try these Solutions  
Plug a projector into your AC outlet.  
Make sure READY Indicator lights.  
Wait 90 seconds after a projector is turned OFF when turning the projector back on.  
NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as  
follows:  
1. LAMP indicator lights bright and READY indicator turns off.  
2. After 90 seconds, READY indicator lights green again and a projector may be  
turned on by pressing Power ON-OFF button.  
Check WARNING TEMP. indicator. If the indicator flashes red, the projector cannot be  
turned on.  
(See "TURNING ON/OFF PROJECTOR" section on page 19.)  
Check Projection Lamp. (Refer to page 39.)  
Adjust focus of a projector.  
Make sure a projection screen is at least 5.3(1.6m) from the projector.  
Check Projection Lens to see if it needs cleaning.  
Image is out of  
focus.  
NOTE : Moving a projector from a cool temperature location to a warm temperature location  
may result in moisture condensation on Projection Lens. In such an event, leave a  
projector OFF and wait until condensation disappears.  
Check Ceiling / Rear feature. (See SETTINGsection on page 35.)  
Picture is Left/Right  
reversed.  
Check Ceiling feature. (See SETTINGsection on page 35.)  
Picture is  
Top/Bottom  
reversed.  
Check Display feature.(See SETTINGsection on page 35.)  
Some displays are  
not seen during the  
Operation.  
Check the connection between your computer or video equipment and a projector.  
When turning a projector on, it takes about 30 seconds to display an image.  
Check the system that you select is corresponding with your computer or video  
equipment.  
No image.  
Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).  
Check audio cable connection from audio input source.  
Adjust the audio source.  
No sound.  
Press VOLUME (+) button.  
Press MUTE button.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
Problem:  
Remote Control Unit  
does not work.  
Try these Solution  
Check the batteries.  
Check ALL-OFF switch on Remote Control Unit is set to ON..  
Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.  
Make sure you are not too far from a projector when using Remote Control Unit.  
Maximum operating range is 16.4(5m).  
Make sure the code of Remote Control is set to conform to projector.  
(See SETTINGsection on page 35, 36.)  
Check cable connection between a projector and your computer.  
Check the mouse setting on your computer.  
Turn a projector on before turning on a computer.  
Wireless Mouse  
function does not  
work.  
WARNING :  
High voltages are used to operate this projector. Do not attempt to open the cabinet.  
after following all operating instructions, contact Boxlight for assistance at 1-800-762-5757 or 360-  
If the problem still persists  
779-7901. Give the model number and explain the difficulty. We will advise you how to obtain service.  
Please have the following information available.  
Serial No. of projector.  
Resolution of the computer.  
Refresh rate of computer.  
This symbol on the nameplate means the product is Listed by Underwriters  
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards  
against risk of fire, casualty and electrical hazards.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TECHNICAL SPECIFICATIONS  
Multi-media Projector  
Projector Type  
13.11" x 3.52" x 9.07" (333mm x 89.5mm x 230.5mm) (not including Adjustble Feet and Lens)  
8.6 lbs (3.9 kg)  
(W x H x D)  
Dimensions  
Net Weight  
0.9" TFT Active Matrix type, 3 panels  
1024 x 768 dots  
LCD Panel System  
Panel Resolution  
Number of Pixels  
Color System  
2,359,296 (1024 x 768 x 3 panels)  
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N  
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i  
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz  
Adjustable from 31to 300”  
High Definition TV Signal  
Scanning Frequency  
(Diagonal)  
Projection Image size  
Horizontal Resolution  
Projection Lens  
800 TV lines  
F 1.7 ~ 2.0 lens with f 37.4 mm ~ 48.3 mm with motor zoom and focus  
5.3~ 40.0(1.6 m ~ 12.2 m)  
200 W  
Throw Distance  
Projection Lamp  
RCA Type x 3 (Video/Y, Pb/Cb, Pr/Cr) and Mini DIN 4 pin x 1 (S-Video)  
RCA Type x 2  
Video Input Jacks  
Audio Input Jacks  
Computer Input Terminals  
Computer Audio Input Jack  
Control Port Connector  
USB Connector  
(VGA) HDB 15 Terminal x 1 and DVI 24 pin x 1  
Mini Jack (stereo) x 1  
Mini DIN 8 pin x 1  
USB Series B receptacle x 1  
RCA Type x 2  
Audio Output Jacks  
Internal Audio Amp  
Built-in Speakers  
1.0 W RMS  
1 speaker, 1.18" x 1.57" (30mm x 40mm)  
0˚ to 15.6˚  
Feet Adjustment  
Voltage and  
Power Consumption  
Operating Temperature  
AC 100 ~ 120 V (3.6 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)  
AC 200 ~ 240 V (1.8 A Max. Ampere), 50 / 60 Hz (Continental Europe)  
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)  
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)  
Storage Temperature  
Power Source  
Operating Range  
Dimensions  
Net Weight  
Laser Pointer  
:
:
:
:
:
AA, UM3 or R06 Type x 2  
16.4(5m) / ±30˚  
2.2x 1.3x 7.6(55mm x 34mm x 192mm)  
0.36 lbs (165 g) (including batteries)  
(Max. Output : 1mW / Wave length : 650±20nm)  
Class II Laser  
Remote Control Transmitter  
Owners Manual  
Accessories  
AC Power Cord  
Wireless Remote Control Transmitter and Batteries  
VGA Cable  
Control Cable for PS/2 port  
Carrying Bag  
Lens Cover  
The specifications are subject to change without notice.  
OPTIONAL PARTS  
The parts listed below are optionally supplied. When ordering those parts, give name and Type No. of it to the sales dealer.  
Control Cable for Serial Port Type No. : POA-MCSRL  
Control Cable for ADB Port Type No. : POA-MCMAC  
MAC Adapter  
Media Card Imager Kit  
Type No. : POA-MACAP  
Type No. : PCMCIA-MOD1  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
CONFIGURATIONS OF THE TERMINALS  
COMPUTER INPUT-1 TERMINAL (ANALOG)  
Terminal : HDB15-PIN  
Connect the display output terminal of the computer to this terminal with the VGA Cable (supplied). When connecting the  
Macintosh computer, MAC Adapter (not supplied) is required.  
1
2
3
4
5
6
7
8
Red Input  
Green Input  
Blue Input  
Sense 2  
9
+5V Power  
Pin Configuration  
10 Ground (Vert.sync.)  
11 Sense 0  
2
1
5
4
3
12 DDC Data  
10  
9
8
7
6
15  
14  
13  
12  
11  
Ground (Horiz.sync.) 13 Horiz. sync.  
Ground (Red)  
Ground (Green)  
Ground (Blue)  
14 Vert. sync.  
15 DDC Clock  
COMPUTER INPUT-1 TERMINAL (DIGITAL)  
Terminal : DVI 24-pin  
Connect the display output terminal of the computer to this terminal with DVI cable (for Single Link T.M.D.S. / not supplied).  
1
2
3
4
5
6
7
8
T.M.D.S. Data2–  
9
T.M.D.S. Data1–  
17 T.M.D.S. Data0–  
18 T.M.D.S. Data0+  
Pin Configuration  
T.M.D.S. Data2+  
10 T.M.D.S. Data1+  
T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield  
1
9
2
3
4
5
6
7
8
No Connect  
No Connect  
DDC Clock  
DDC Data  
12 No Connect  
20 No Connect  
10 11 12 13 14 15 16  
17 18 19 20 21 22 23 24  
13 No Connect  
21 No Connect  
14 +5V Power  
22 T.M.D.S. Clock Shield  
23 T.M.D.S. Clock+  
24 T.M.D.S. Clock–  
15 Ground (for +5V)  
16 Hot Plug Detect  
No Connect  
CONTROL PORT CONNECTOR  
Terminal : Mini DIN 8-PIN  
Connect control port (PS/2, Serial or ADB port) on your computer to this connector with Control Cable.  
(Control Cable for PS/2 port is supplied, and Control Cables for Serial port and ADB port are not supplied.)  
PS/2  
-----  
Serial  
R X D  
-----  
ADB  
-----  
Pin Configuration  
1
2
3
4
5
6
7
8
CLK  
DATA  
GND  
-----  
ADB  
-----  
-----  
8
7
6
GND  
GND  
-----  
5
4
3
RTS / CTS  
T X D  
GND  
2
1
-----  
-----  
GND  
-----  
-----  
GND  
GND  
USB CONNECTOR (Series B)  
Connect USB port terminal on your computer or peripheral equipment to this connector with USB Cable (not supplied).  
Pin Configuration  
1
2
3
4
Vcc  
- Data  
+ Data  
Ground  
2
3
1
4
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
BOXLIGHT CORPORATION (BOXLIGHT) warrants that each BOXLIGHT CP-300t (the Product) sold hereunder  
will conform to and function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall  
apply only to the first person or entity that purchases the Product for personal or business use and not for the purpose  
of distribution resale. Said warranty shall continue for a period of two (2) years from the date of such purchase.  
BOXLIGHT does not warrant that the Product will meet the specific requirements of the first person or entity that  
purchases the Product for personal or business use. Lamp is warrantied for 120 days.  
BOXLIGHT CORPORATIONs liability for the breach of the foregoing limited warranty is limited to the repair or  
replacement of the Product or refund of the purchase price of the Product, at BOXLIGHTs sole option. To exercise  
the Purchasers rights under the foregoing warranty, the Product must be returned at the Purchasers sole cost and  
expense, to BOXLIGHT or any authorized service center provided, however, that the Product must be accompanied by  
a written letter explaining the problem and which includes (i) proof of purchase; (ii) the dealers name; (iii) the model  
and serial number of the Product. A return authorization number, issued by the BOXLIGHT customer service  
department, must also be clearly displayed on the outside of the shipping carton containing the Product.  
WARRANTY LIMITATION AND EXCLUSION  
BOXLIGHT CORPORATION shall have no further obligation under the foregoing limited warranty if the Product has  
been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized  
modification, tampering, alterations, or service other than by BOXLIGHT or its authorized agents, causes other than  
from ordinary use or failure to properly use the Product in the application for which said Product is intended.  
DISCLAIMER OR UNSTATED WARRANTIES  
The warranty printed above is the only warranty applicable to this purchase.  
All other warranties express or implied, including, but not limited to, the implied warranties or merchantability and  
fitness for a particular purpose are disclaimed. There are no warranties that extend beyond the face of hereof and the  
foregoing warranty shall not be extended, altered or varied except by written instrument signed by BOXLIGHT  
CORPORATION.  
LIMITATION OR LIABILITY  
It is understood and agreed that BOXLIGHTs liability whether in contract, in tort, under any warranty, in negligence or  
otherwise shall not exceed the return of the amount of the purchase price paid by purchaser and under no  
circumstances shall BOXLIGHT be liable for special, indirect or consequential damages. The price stated for the  
Product is a consideration in limiting BOXLIGHTs liability. No action regardless of form, arising out of the agreement  
to purchase the product, may be brought by purchaser more than one year after the cause of action has accrued.  
Boxlight  
19332 Powder Hill Place  
Poulsbo, WA 98370-7407 USA  
USA and Canada 800-762-5757  
International 360-779-7901  
Printed in Japan  
Part No. 610 292 7931 (1AA6P1P2784-- MS6E)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Belkin Computer Keyboard F8E849 BNDL User Manual
Bloomfield Coffeemaker 9600 Single Cup User Manual
Bogen Headphones HAA20 User Manual
Bolens Lawn Mower 120 442R000 User Manual
Bose Speaker System VCS 10 User Manual
Briggs Stratton Pressure Washer 020224 1 User Manual
Bushnell Digital Camera 11 0013Y User Manual
Cadence Stereo Amplifier MONO CLASS D User Manual
Campbell Hausfeld Nail Gun IN703700AV User Manual
Chauvet Indoor Furnishings DMX 500 User Manual