USER’S GUIDE
BOXLIGHT CP-11t
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
e. If the projector has been dropped or the cabinet has been
damaged.
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
This projector is equipped with a
grounding type AC line plug.
Should you be unable to insert the
plug into the outlet, contact your
electrician. Do not defeat the
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
safety purpose of this grounding
type plug.
GROUND
Follow all warnings and instructions marked on the projectors.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
If the projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained.
Do not cover the ventilation slot on the projector.
Heat build-up can reduce the service life of your projector, and
can also be dangerous.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
20cm
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
WALL
PROJECTOR
(FRONT)
PROJECTOR
(SIDE)
c. If the projector has been exposed to rain or water.
50cm
50cm
50cm
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FEATURES AND DESIGN
5
6
COMPUTER MODE
22
SELECTING COMPUTER MODE
22
SELECTING COMPUTER SYSTEM
AUTOMATIC MULTISCANNING SYSTEM
COMPATIBLE COMPUTER SPECIFICATIONS
22
22
23
PREPARATION
PC ADJUSTMENT
24
NAME OF EACH PART OF THE PROJECTOR
6
PICTURE IMAGE ADJUSTMENT
ADJUST PICTURE IMAGE MANUALLY
NORMAL FUNCTION
26
26
26
27
SETTING-UP THE PROJECTOR
POSITIONING THE PROJECTOR
ADJUSTABLE FEET
7
7
7
8
8
9
AUTO IMAGE FUNCTION
CONNECTING THE AC POWER CORD
VENTILATION
MOVING THE PROJECTOR
PICTURE POSITION ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
27
28
CONNECTING THE PROJECTOR 10
VIDEO MODE
29
TERMINALS OF THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
CONNECTING TO THE COMPUTER
10
11
12
SELECTING VIDEO MODE
SELECTING COLOR SYSTEM
PICTURE SCREEN ADJUSTMENT
29
29
29
PICTURE IMAGE ADJUSTMENT
ADJUSTING THE PICTURE IMAGE MANUALLY
NORMAL FUNCTION
30
30
30
BEFORE OPERATION
14
OPERATION OF THE REMOTE CONTROL
LASER POINTER FUNCTION
14
14
15
SETTING
31
REMOTE CONTROL BATTERIES INSTALLATION
TOP CONTROLS AND INDICATORS
16
SETTING MENU
SETTING LANGUAGE
31
31
OPERATING ON-SCREEN MENU
HOW TO OPERATE THE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU
MENU BAR
17
17
17
18
APPENDIX
32
BASIC OPERATION
19
OPERATING WIRELESS MOUSE
MAINTENANCE
32
33
33
33
33
34
34
TEMPERATURE WARNING INDICATOR
AIR FILTER CARE AND CLEANING
CLEANING THE PROJECTION LENS
LAMP REPLACEMENT
TURNING ON / OFF THE PROJECTOR
ADJUSTING THE IMAGE
ZOOM ADJUSTMENT
19
20
20
20
20
21
21
FOCUS ADJUSTMENT
KEY STONE ADJUSTMENT
NO SHOW FUNCTION
LAMP REPLACEMENT MONITOR TIMER
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
35
37
PICTURE FREEZE FUNCTION
SOUND ADJUSTMENT
SOUND VOLUME ADJUSTMENT
SOUND MUTE ADJUSTMENT
21
21
21
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its
respective corporation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND DESIGN
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of
use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal
display (LCD) technology.
● Compatibility
● Automatic Multiscanning System
This projector is compatible with many different
types of personal computers and video
devices, including;
This projector automatically tunes to most
personal computers currently distributed by
simply connecting. It is free from complicated
adjustments to project picture images from
most Personal Computers.
● IBM-compatible computers, including
laptops, up to 1024 x 768 resolution.
● Apple Macintosh and PowerBook
computers up to 1024 x 768 resolution.
● Various video equipment using any of the
world wide video standards, including
NTSC, NTSC4.43, SECAM, PAL, PAL-M
and PAL-N.
● Multilanguage Menu Display
Operation menu is displayed in; English,
Deutsch, Français, Italiano, Español, or
Japanese.
● Image Resolution
● Laser Pointer Function
Picture Image of the computer is projected in
the resolution of 800 x 600 and it is provided
just as appearing on your computer's monitor.
Screen resolutions between 800 x 600 and
1024 x 768 are compressed to 800 x 600, and
this projector cannot display screen resolutions
above 1024 x 768. If your computer's screen
resolution is higher than 1024 x 768, reset it to
a lower resolution before you connect the
projector.
The Remote Control Unit of this projector
includes the Laser Pointer function providing
convenience for your presentations.
● Other Features
This projector has Motor Zoom/Focus, No
Show, Picture Freeze, Keystone, Mute
functions, and the Air Pad Remote Control.
● Portability
● Accessories
This projector is quite compact in size and
weight. Having a sophisticated shape like an
attaché case with a retractable carrying handle,
the projector will help you make powerful
presentations wherever you go.
This projector comes with the parts listed
below. Check to make sure all are included. If
any parts are missing, contact Boxlight
immediately.
● Owner's Manual.
● AC Power Cord.
● Wireless Remote Control Unit.
● Batteries for Remote Control Unit.
● VGA Cable.
● Control Cable for PS/2 Port.
● Lens Cover.
● Dust Cover
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
NAME OF EACH PART OF THE PROJECTOR
FRONT OF THE CABINET
PROJECTION LENS
LENS COVER
CARRY HANDLE
INFRARED REMOTE RECEIVER
SPEAKER (Monaural)
BACK OF THE CABINET
EXHAUST VENT
HOT AIR EXHAUSTED !
Air blown from the exhaust vent is hot.
When using or installing the projector,
following attention should be taken.
● Do not put a flammable object near this
vent.
● Keep heat-sensitive objects away from the
exhaust vent.
● Do not touch this area especially screws
and metallic parts. This area will become
hot while the projector is used.
INFRARED
REMOTE RECEIVER
POWER CORD CONNECTOR
BOTTOM OF THE CABINET
AIR INTAKE VENTS
These Air Intake Vents
should not be blocked.
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
LAMP COVER
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
SETTING-UP THE PROJECTOR
POSITIONING THE PROJECTOR
● This projector is designed to project on a flat projection surface.
● The projector can be focused from 4.6’(1.4m) ~ 35.4’(10.8m).
● Refer to the figure below to adjust the screen size.
35.4’ (10.8m)
24.0’ (7.3m)
200”
300”
18.0’ (5.5m)
11.8’ (3.6m)
150”
231”
4.6’ (1.4m)
100”
H1
H2
154”
115”
40”
77”
30”
30”
60”
100”
150”
200”
300”
Screen Size
(W x H) mm
610 x 457
1219 x 914
34.3”(870mm)
1.7”(44mm)
2032 x 1524
3048 x 2286
4064 x 3048
6096 x 4572
17.1”(435mm)
0.9”(22mm)
57.1”(1451mm) 85.7”(2177mm) 114.3”(2903mm) 171.4”(4354mm)
2.9”(73mm) 4.3”(109mm) 5.7”(145mm) 8.6”(218mm)
Height (H1)
Height (H2)
ROOM LIGHT
The brightness in the room has a great influence on the picture quality. It is recommended to limit ambient
lighting in order to provide the best image.
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by
rotating the ADJUSTABLE FEET. Projection angle can
be adjusted to 10 degrees.
Lift the front of the projector and pull the FEET LOCK
LATCHES on both sides of the projector.
1
Release the FEET LOCK LATCHES to lock the
ADJUSTABLE FEET and rotate the ADJUSTABLE
FEET to fine tune the position and the tilt.
2
To shorten the ADJUSTABLE FEET, lift the front of the
projector and pull and undo the FEET LOCK LATCHES.
3
FEET LOCK
LATCHES
The position and the keystone distortion of the image
can also be adjusted using the Menu Operation. (Refer
to P 20, 28 and 29.)
ADJUSTABLE FEET
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
CONNECTING THE AC POWER CORD
This projector uses nominal input voltages of 100-120 V
AC or 200-240 V AC. The projector automatically
selects the correct input voltage. It is designed to work
with single-phase power systems having a grounded
neutral conductor. To reduce the risk of electrical
shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you
are not sure of the type of power supply being in use.
Connect the projector with the peripheral equipment
before turning the projector on. (Refer to pages 10 ~ 13
for connection.)
Connect the AC power supply cord (supplied) to the
projector.
The socket-outlet must be near this equipment and
must be easily accessible.
CAUTION
For safety, unplug the AC Power Cord when the
appliance is not in use.
When this projector is connected to the outlet with
the AC Power Cord, the appliance is in Stand-by
Mode and consumes some electric power.
AC outlet side (Male)
Projector side (Female)
VENTILATION
This projector is equipped with cooling fans for protection from overheating. Pay attention to the following to
ensure proper ventilation and avoid a possible risk of fire and malfunction.
● Do not cover the vent slot.
● Keep the rear grill at least 3’(1m) away from any
object.
● Keep sides clear of any obstructions. Obstructions
EXHAUST VENT
(REAR SIDE)
may block cooling air.
AIR INTAKE VENTS
(BOTH SIDES)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
MOVING THE PROJECTOR
Use the Carry Handle when moving the Projector.
When moving the projector, replace the lens cover and retract
feet to prevent damage to the lens and cabinet.
When this projector is not in use for an extended period,
replace the lens cover, retract the Adjustable Feet and apply
the dust cover supplied with this projector.
CAUTION WHEN CARRYING OR TRANSPORTING THE PROJECTOR
● Do not drop or bump the projector, otherwise damages or malfunctions may result.
● When transporting the projector, use a carrying case recommended by Boxlight.
● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to the projector. To transport the projector through a courier or transport service, use
a case recommended by Boxlight.
● For carrying or transportation cases, contact a Boxlight at 1-800-762-5757 or 360-779-7901.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
TERMINALS OF THE PROJECTOR
S-VIDEO INPUT JACK
VIDEO INPUT JACK
Connect the S-VIDEO output
from the video equipment to this
terminal.
Connect the video output from
the video equipment to this
terminal.
(Refer to P11.)
S-VIDEO
(Refer to P11.)
AUDIO INPUT JACKS
COMPUTER AUDIO INPUT JACK
AUDIO
IN
Connect the audio outputs from
the video equipment to these
terminals.
R-AUDIO-L(MONO)
VIDEO
Connect the audio output from
the computer to this terminal.
(Refer to P12, 13.)
OUT
(Refer to P11.)
COMPUTER IN
MONITOR OUT
● When the audio output is
monaural, connect it to the Left
jack.
AUDIO OUTPUT JACK (STEREO)
Connect the audio amplifier to
this terminal.
(Refer to P11, 12, 13.)
CONTROL PORT
COMPUTER INPUT TERMINAL
Connect the computer output to
this terminal.
(Refer to P12, 13.)
CONTROL PORT CONNECTOR
When controlling the computer
with the Remote Control of this
projector, connect the mouse
port of your personal computer
to this terminal.
MONITOR OUTPUT TERMINAL
This terminal outputs the signal
from the COMPUTER IN
terminal. Connect an external
monitor to this terminal.
(Refer to P12, 13.)
(Refer to P12, 13.)
COMPUTER INPUT / MONITOR OUTPUT TERMINAL
Terminal : HDB15-PIN
Connect the display output terminal of the computer to COMPUTER INPUT terminal of this projector with the VGA Cable
(supplied). And connect the monitor to MONITOR OUTPUT with the monitor cable (not supplied). When connecting the
Macintosh computer, the MAC Adapter (not supplied) is required.
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
Sense 2
9
Non Connect
Pin Configuration
10 Ground (Vert.sync.)
11
12
Sense 0
Sense 1
Horiz. sync.
Vert. sync.
Reserved
2
1
5
4
3
10
9
8
7
6
Ground (Horiz.sync.) 13
Ground (Red)
Ground (Green) 15
Ground (Blue)
15
14
13
12
11
14
CONTROL PORT CONNECTOR
Terminal : DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with the Control Cable (the Control
Cable for PS/2 port is supplied).
PS/2
-----
CLK
DATA
GND
-----
-----
GND
-----
Serial
R X D
-----
-----
GND
RTS
T X D
GND
GND
ADB
-----
ADB
-----
GND
-----
-----
Pin Configuration
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
-----
GND
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
Video Source (example)
Video Cassette Recorder
Video Disc Player
Video / Audio Output
S-VIDEO Output
Used cables for connection
• VIDEO CABLE ●
• S-VIDEO CABLE ●
• AUDIO CABLE (stereo) ●
Use either the VIDEO jack
or S-VIDEO jack. When
the both jacks are
connected, the S-VIDEO
jack has priority over the
VIDEO jack.
● These cables are not supplied
with this projector.
Video Audio Cable ●
S-VIDEO Cable ●
Terminals
of the Projector
S-VIDEO
AUDIO
IN
R-AUDIO-L(MONO)
VIDEO
OUT
COMPUTER IN
MONITOR OUT
CONTROL PORT
Audio Cable (Stereo) ●
Audio Input
External Audio Equipment
NOTE :
When connecting the cable, the power cords of
both the projector and the external equipment
should be disconnected from AC outlet. Turn the
projector and peripheral equipment on before the
computer is switched on.
Audio Speaker
(stereo)
Audio Amplifier
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
CONNECTING TO THE COMPUTER
To connect to the computer, refer to the figure below.
Used cables for connection
• VGA CABLE
• CONTROL CABLE FOR PS/2 PORT
• CONTROL CABLE FOR SERIAL PORT,or ADB PORT ●
• MAC ADAPTER ●
• MONITOR CABLE ●
• PC AUDIO CABLE (stereo) ●
● These cables are not supplied with this projector.
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA)
Desktop type
Laptop type
Monitor
Audio Speaker
(stereo)
Audio Amplifier
Audio Input
To each terminal of your computer
Serial port PS/2 port ADB port Audio Output
To the Monitor
Monitor Output
MAC Adapter ●
Set the slide
ON
DIP
switches following
the chart on the
next page.
1
2
3
4
5
6
Terminal
Terminal
Terminal
Audio Cable (stereo) ●
Control Cable for ADB Port ●
Control Cable for PS/2 Port
Control Cable for Serial Port ●
VGA Cable
Monitor Cable ●
NOTE :
When connecting the cable, the power cords of both the projector and the external equipment should be disconnected
from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
S-VIDEO
AUDIO
IN
R-AUDIO-L(MONO)
VIDEO
OUT
COMPUTER IN
MONITOR OUT
CONTROL PORT
COMPUTER
IN
MONITOR
OUT
CONTROL
PORT
AUDIO
IN
AUDIO
OUT
● MAC ADAPTER (Not supplied)
Set the switches as shown
in the table below depend-
ing on the RESOLUTION
MODE that you want to
use before your turn on the
projector and computer.
ON
Use one of these Control
ON
DIP
Cables corresponding
with the terminal of your
computer.
1
2
3
4
5
6
OFF
1
2
3
4
5
6
13" MODE (640 x 480)
16" MODE (832 x 624)
19" MODE (1024 x 768)
ON ON OFF OFF OFF OFF
OFF ON OFF ON OFF OFF
OFF ON ON OFF OFF OFF
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
Left Side
POWER ON-OFF BUTTON
Used to turn the projector on
or off. (P19)
COMPUTER BUTTON
Used to select COMPUTER
output source. (P22)
ON-OFF
COMPUTER VIDEO
ZOOM FOCUS
VIDEO BUTTON
VOLUME
Used to select VIDEO
source. (P29)
D.ZOOM
MUTE
MENU
POINT BUTTON
MENU BUTTON
Used to select MENU
operation. (P17, 18)
Used to move the pointer on
the MENU, to adjust the item,
or to pan the image in DIGITAL
ZOOM mode. (P28)
It is also used as a PC mouse
in Wireless Mouse Operation.
(P32)
SELECT BUTTON
● When pressing the center of this
button, it works as the SELECT
button.
Used to execute the item
selected or to expand the
image in DIGITAL ZOOM
mode. (P28)
It is also used as a PC mouse
in Wireless Mouse Operation.
(P32)
ALL-OFF SWITCH
LASER
When using the Remote Control
Unit, turn this switch to “ON” and
turn it “ALL OFF” when it is not
used.
RIGHT CLICK BUTTON
KEYSTONE
Used to compress the image
in DIGITAL ZOOM mode.
(P28)
NO SHOW
FREEZE
It is also used as a PC mouse
in Wireless Mouse Operation.
(P32)
AUTO IMAGE
NORMAL
LASER BUTTON
Used to operate the laser
pointer function. The laser
beam is emitted while
pressing this button within 1
minute. When using the laser
pointer for more than
1
minute, release the button and
press it again.
Laser Pointer Function
This remote control emits a laser beam as the Laser Pointer from the Laser Light Window. When the LASER button is
pressed, the laser light goes on. And when the button is pressed more than 1 minute or the button is released, light goes off.
Laser light is emitted with the RED light which tells the laser beam being emitted.
The laser emitted is a class II laser; therefore, do not look into the Laser Light Window or shine the laser beam on yourself or
other people. The three marks bellow are the caution labels for the laser beam.
CAUTION : Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
These caution labels are put on the remote control.
Laser Light Window
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
Operating Range
ON-OFF
Point the remote control toward the
projector (the Remote Receiver)
whenever pressing the buttons.
Maximum operating range for the
remote control is about 16.4’ (5m)
and 60° front and rear of the
projector
COMPUTER VIDEO
ZOOM FOCUS
ZOOM BUTTON
Used to adjust zoom.
(P20)
VOLUME BUTTON
Used to adjust volume.
(P21)
VOLUME
FOCUS BUTTON
Used to adjust focus.
(P20)
D.ZOOM
MUTE
MENU
D.ZOOM BUTTON
Used to turn the projector
into DIGITAL ZOOM
mode and resize the
image. (P28, 29)
60°
MUTE BUTTON
16.4’
Used to mute sound.(P21)
(5 m)
FREEZE BUTTON
Used to freeze the picture.
(P21)
LASER
NO SHOW BUTTON
Used to turn the picture
into black image. (P21)
KEYSTONE
NO SHOW
FREEZE
NORMAL BUTTON
Used to reset to normal
picture adjustments preset
by the factory. (P26, 30)
AUTO IMAGE
NORMAL
AUTO IMAGE BUTTON
Use to operate AUTO
IMAGE function. (P27)
16.4’
(5 m)
KEYSTONE BUTTON
60°
Used to correct the
keystone distortion.
(P20, 28, 29)
Remote Control Batteries Installation
Remove the battery
compartment lid.
Slide the batteries into the
compartment.
Replace the compartment
lid.
1
2
3
Press the lid down-
ward and slide it.
Two AA size batteries
For correct polarity (+
and –), be sure the
battery terminals are in
contact with the pins in
the compartment.
To insure safe operation, please observe the following precautions :
● Use (2) AA type alkaline batteries.
● Replace two batteries at the same time.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the Remote Control Unit to moisture, or heat.
● Do not drop the remote control unit.
● If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
ZOOM BUTTONS
Used to select zoom adjust.
(P20)
POWER ON–OFF BUTTON
FOCUS BUTTONS
Used to turn the projector
on or off. (P19)
Used to select focus adjust.
(P20)
ZOOM
FOCUS
VOLUME
LAMP INDICATOR
VOLUME BUTTONS
This indicator is dim when
the projector is turned on.
And bright when the
projector is in stand-by
mode.
Used to adjust volume.
(P21)
LAMP
MODE BUTTON
READY
Used to select input source
either Computer or Video.
(P22, 29)
ON–OFF
MENU
MODE
READY INDICATOR
This indicator is lit in green
when the projector is ready
to be turned on.
WARNING
TEMP.
SELECT
SELECT BUTTON
Used to execute the item
selected. It is also used to
expand the image in DIGITAL
ZOOM mode. (P28)
WARNING TEMP. INDICATOR
LAMP
REPLACE
This indicator flashes red
when internal projector
temperature is too high.
(P33)
AUTO IMAGE
NORMAL
POINT BUTTONS
Used to select an item or
adjust the value on the MENU.
It is also used to pan the image
in DIGITAL ZOOM mode.
(P28)
LAMP REPLACE INDICATOR
This indicator turns to
yellow when the life of the
projection lamp draws to an
end. (P34)
NORMAL BUTTON
Used to reset to normal
picture adjustment preset
by factory. (P26, 30)
MENU BUTTON
Used to open or close the
MENU operation.
(P17, 18)
AUTO IMAGE BUTTON
Used to operate AUTO
IMAGE function. (P27)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through the
WIRELESS REMOTE CONTROL
ON-SCREEN MENU. Refer to the following pages to
operate each adjustment on the ON-SCREEN MENU.
POINT BUTTON
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
1 MOVING THE POINTER
Move the pointer (see the NOTE below) by pressing POINT
button(s) on the TOP CONTROL or the REMOTE CONTROL.
SELECT BUTTON
Used to select the item.
2 SELECT THE ITEM
TOP CONTROL
Select the item by pressing SELECT button.
SELECT BUTTON
Used to select the item.
NOTE : Pointer is the icon on the ON-SCREEN Menu to
select the item. See the figures on the section
"FLOW OF ON-SCREEN MENU" below.
SELECT
POINT BUTTONS
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
FLOW OF ON-SCREEN MENU
MENU BAR
Display ON-SCREEN MENU
Press MENU button to display the ON-SCREEN MENU
(MENU BAR). The red frame is the POINTER.
1
POINTER
(red frame)
SELECT
BUTTON
ITEM ICON
Select the Item
Move the POINTER (red frame) to the ITEM ICON that
you want to select by pressing POINT RIGHT / LEFT
buttons.
2
Select the ITEM by pressing SELECT button. The
dialog box of the ITEM appears.
POINTER
(red frame)
3
Control and adjust through ON-SCREEN MENU
MENU
Move the POINTER downward by pressing POINT
DOWN button. (The shape of the POINTER becomes
an arrow.)
4
POINT
DOWN
Move the POINTER to the ITEM that you want to adjust
and adjust the ITEM by pressing SELECT button.
Refer to the following pages for details of respective
adjustments.
BUTTON
5
POINTER
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
MENU BAR
MENU BAR IN COMPUTER MODE
Press MENU BUTTON while in Computer mode.
MODE MENU
AUTO IMAGE MENU
PC ADJUST MENU
SETTING MENU
Used to select
the Computer
input mode.
Used to adjust Fine
sync., Total dots,
and Picture Position
automatically.
Used to adjust the
parameters to
match with the input
signal format.
Used to set the Display
Menu and to reset
Lamp Replacement
Monitor Timer.
(Refer to P22)
(Refer to P27)
(Refer to P24, 25)
(Refer to P31)
SYSTEM MENU
IMAGE MENU
POSITION MENU
SCREEN MENU
LANGUAGE MENU
Used to select a
computer
system.
Used to adjust the
computer image. [Fine
sync. / Total dots /
White Balance /
Used to adjust
the position of
the image.
Used to adjust
the size of the
image.
Used to select
the language
used in the
Menu.
(Refer to P22)
(Refer to P27)
(Refer to P28)
Contrast / Brightness]
(Refer to P26)
(Refer to P31)
MENU BAR IN VIDEO MODE
MODE MENU
Press MENU BUTTON while in Video mode.
IMAGE MENU
Used to adjust the
Color /
Tint / White Balance /
Contrast / Brightness/
picture image. [
Used to select
the Video input.
(Refer to P29)
These icons have the
same function as the
Computer Mode.
Sharpness
]
(Refer to P30)
SYSTEM MENU
SCREEN MENU
Used to select a
color system among
Used to set the size
of the image either
Regular or Wide,
or to correct the
PAL, SECAM, NTSC,
[
NTSC 4.43, PAL-M and
PAL-N
].
(Refer to P29)
Keystone distortion.
(Refer to P29)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
TURNING ON / OFF THE PROJECTOR
TURNING ON THE PROJECTOR
Complete the peripheral connections (with Computer, VCR,
etc.) before turning on the projector. (Refer to "CONNECTING
TO THE PROJECTOR" on Pages 10~13 for connecting that
equipment.)
1
Connect the projector's AC power cord into a wall outlet. The
LAMP indicator lights RED, and the READY indicator lights
GREEN.
2
3
30
Press the power ON-OFF button on the Remote Control Unit or
on the Top Control to ON. The LAMP POWER indicator dims,
and the Cooling Fans start to operate. The Preparation Display
appears on the screen and the count-down starts. The signal
from the source appears after 30 seconds.
The Preparation Display disappears after 30 seconds.
TURNING OFF THE PROJECTOR
Press the power ON-OFF button on the Remote Control Unit or
on the Top Control, and the message "Power off?" appears on
the screen.
1
2
Power off?
Press the power ON-OFF button again to turn off the projector.
The LAMP indicator lights bright and the READY indicator turns
off. The Cooling Fans operate for 90 seconds after the
projector is turned off. (During this "Cooling Down" period, this
appliance cannot be turned on.)
The message disappears after 4 seconds.
When cooling the projector has finished, the READY indicator
turns to green again and you can turn the projector on. After
cooling down completely, disconnect the AC power cord.
3
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN IT ON, WAIT AT LEAST 5
MINUTES BEFORE TURNING IT OFF.
When the TEMPERATURE WARNING indicator flashes red, the projector is automatically turned off.
Wait at least 5 minutes before turning the projector on again.
If the TEMPERATURE WARNING indicator continues to flash, follow procedures below:
1. Disconnect the AC power cord from the AC outlet.
2. Check the air filters for dust accumulation.
3. Clean the Air Filter. (See "AIR FILTER CARE AND CLEANING" section on page 33.)
4. Press the power ON-OFF button to ON.
If the TEMPERATURE WARNING indicator still continues to flash, call Boxlight at 1-800-762-5757 or
360-779-7901.
NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling
Fan is working, TEMPERATURE WARNING INDICATOR flashes red.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
ADJUSTING THE IMAGE
ZOOM ADJUSTMENT
Press the ZOOM ●/● button(s) on the Top Control or on the
Remote Control Unit to turn on the ZOOM mode.
1
2
Press the ZOOM ● button to make the image larger, and press
the ZOOM ● button to make the image smaller.
Zoom
In the Computer mode, the image can be expanded, compressed,
and panned with the Digital Zoom function. Refer to page 28 for the
Digital Zoom operation.
The message disappears after 4 seconds.
FOCUS ADJUSTMENT
Press the FOCUS ●/● button(s) on the Top Control or on the
Remote Control Unit to turn on the FOCUS mode.
1
2
Adjust the focus of the image by pressing the FOCUS ●/●
button.
Focus
The message disappears after 4 seconds.
KEYSTONE ADJUSTMENT
If the picture has keystone distortion, correct image with KEYSTONE adjustment.
Press the KEYSTONE ●/● button on the Remote Control Unit
or select the Keystone on the SCREEN menu. (Refer to page
28, 29.) The message “Keystone” is displayed.
1
Keystone
Correct the Keystone distortion by pressing the KEYSTONE
●/● button or the POINT UP/DOWN button(s). Press the
KEYSTONE ● button or the POINT UP button to reduce the
upper part or the image, and press the KEYSTONE ● button or
the POINT DOWN button to reduce the lower part.
2
The message disappears after 4 seconds.
Reduce the upper width with the KEY STONE ●
button or the POINT UP button.
Reduce the lower width with the KEY STONE ●
button or the POINT DOWN button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
NO SHOW FUNCTION
Press the NO SHOW button on the Remote Control Unit to black out
the image. This function is cancelled when the NO SHOW button is
pressed again or any other function button is pressed.
No show
The message disappears after 4 seconds.
PICTURE FREEZE FUNCTION
Press the FREEZE button on the Remote Control Unit to freeze the picture on-screen. This function is cancelled when
the FREEZE button is pressed again or any other function button is pressed.
SOUND ADJUSTMENT
Indicates the level of the volume.
SOUND VOLUME ADJUSTMENT
Press the VOLUME (+/–) button(s) on the Top Control or on the
Remote Control Unit to adjust the volume. The Volume dialog box
appears on the screen for a few seconds.
The VOLUME (+) button increases the volume, and the VOLUME (–)
button decreases the volume.
Press the MUTE button to turn
SOUND MUTE ADJUSTMENT
the Mute function On or Off.
Press the MUTE button on the Remote Control Unit to mute the
sound. To restore the sound to its previous level, press the MUTE
button again or press the VOLUME (+/–) button(s).
The display disappears after 4 seconds.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
SELECTING COMPUTER MODE
DIRECT OPERATION
MODE button
COMPUTER
Select COMPUTER mode by pressing the MODE button on the Top
Control or the COMPUTER button on the Remote Control Unit.
VIDEO
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Computer
press the SELECT button.
and
CURRENT MODE DISPLAY
When selecting the Computer Mode, the Current Mode display
appears. It shows the information of the computer of the mode
selected.
Providing the information of the computer detected
by the projector.
SELECTING COMPUTER SYSTEM
AUTOMATIC MULTISCANNING SYSTEM
This projector automatically tunes to most different types of computer
based on VGA, SVGA or XGA (refer to “COMPATIBLE COMPUTER
SPECIFICATION” on page 23). When selecting Computer, this
projector automatically tunes to the incoming signal and projects the
proper image without any special setting. (Setting of the Computer
System may be required when connecting some computers.)
SYSTEM BOX
Note : The projector may provides the messages below.
Display the SYSTEM
being selected.
The projector cannot discriminate or detect the
Go to PC adj.
input signal from the computer. Adjust and set the
computer system manually. (Refer to page 24.)
There is no signal input from the computer. Make
sure the connection of the computer and the
projector is set correctly.
No signal
(Refer to TROUBLESHOOTING on page 35.)
The system being selected.
SELECT COMPUTER MODE MANUALLY
To set the Computer system manually, select the mode on the ON-
SCREEN MENU.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
SYSTEM and press the SELECT button. Another dialog box
COMPUTER SYSTEM Menu will appear.
1
The systems on this
dialog box can be
selected.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the system that you want to set,
2
and then press
SELECT button.
Close the SYSTEM
Menu.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below
and less than 135 MHz of Dot Clock.
ON-SCREEN
DISPLAY
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
34.97
35.00
15.734
15.625
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
59.88
70.09
70.09
74.38
72.81
75.00
66.60
66.67
30
SVGA 10
SVGA 11
SVGA 12
MAC1 6
XGA 1
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
47.90
32.70
38.00
49.72
48.36
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
46.90
47.00
60.24
71.92
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
43.59
77.07
75.70
43.48
58.20
58.30
75.08
VGA 3
VGA 4
VGA 5
VGA 6
XGA 2
MAC LC13
MAC 13
RGB
XGA 3
XGA 4
640 x 480
(Interlace)
768 x 576
(Interlace)
XGA 5
RGB
25
XGA 6
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
XGA 7
XGA 8
1024 x 768
(Interlace)
XGA 9
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
MAC 19
1024 x 768
1024 x 768
1024 x 768
(Interlace)
1024 x 768
1024 x 768
1024 x 768
NOTE : Specifications are subject to change without notice.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
PC ADJUSTMENT
This Projector can automatically tune to the display signals from most personal computers currently distributed.
However, some computers employ the special signal formats which are different from the standard ones and
may not be tuned by Multiscanning of this projector. If this happens, the projector cannot reproduce a proper
image and the image is recognized as a flickering picture, a non-synchronized picture, a non-centered picture or
a skewed picture.
This projector has PC ADJUSTMENT function, to enable you to precisely adjust several parameters to match
with those exceptional signal formats and the projector has five independent memory areas to memorize those
parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use
it.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT RIGHT/LEFT buttons to select PC
1
ADJUST
and press the SELECT button. Another dialog
box “Where to reserve” Menu will appear.
In this dialog box, you can store the parameter into the area
from “Mode 1” to “Mode 5.” When memorizing the new
computer parameter, select the Mode with the message “Free”
by pressing the POINT UP/DOWN buttons and the SELECT
button. To change the parameters of the Mode previously set,
select the Mode with “Stored.”
2
3
This Mode has
parameters being
stored.
When the Mode is selected, Parameter adjustment dialog box
appears. Move the arrow to the item that you want to change
by pressing the POINT UP/DOWN buttons, and adjust each
item to match with your computer. To change the value, press
either the POINT RIGHT button or the POINT LEFT button.
Refer to the next page for adjusting each item.
The Vacant Mode.
Manual set Computer
Mode (1 to 5).
Close the PC
ADJUSTMENT Menu.
Move the arrow to “Stored” and press the SELECT button. The
parameter is memorized in the selected Mode.
4
5
To activate the Mode manually adjusted in this PC
ADJUSTMENT Menu, select the Mode at the SYSTEM
SELECT Menu. (Refer to page 22.)
Press the POINT
RIGHT/LEFT
button(s) to
adjust the value.
Press the
SELECT button
to set Full screen
function on/off.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Total lines
The number of the total vertical lines. Adjust the number to match
the image of your personal computer.
Total dots
The number of the total dots in one horizontal period. Adjust the
number to match the image of your personal computer.
Horizontal / Vertical
Adjustment of the horizontal or vertical picture position. When the
image is not centered on the screen, adjust each of those items.
Clamp
Press the
SELECT button
to select the
typical resolution
of the image.
Adjustment of the clamp level. When the image has a dark bar(s),
try this adjustment.
Display area
Adjustment of the area displayed with this projector. Select the
resolution at the Display area dialog box, or adjust the number at
the column of “H” or “V” to match the resolution of the image.
Full Screen
Set “On” to resize the image with 4 x 3 aspect ratio to fit the
screen.
Each of the keys operates as follow.
Reset
Recalls the parameter data that was previously
adjusted.
Mode free
Stored
Quit
Clears the parameter data previously set.
Stores the parameters in the memory.
Closes the PC ADJUST Menu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
ADJUST PICTURE IMAGE MANUALLY
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
IMAGE and press the SELECT button. Another dialog box
1
2
PICTURE IMAGE ADJUSTMENT Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to change by
pressing the POINT UP/DOWN buttons. To change the value,
press either the POINT RIGHT button or the POINT LEFT
button.
Indicate the level
of the item.
Fine sync.
Adjust the picture as necessary to eliminate flicker from the display.
(From 0 to 255.)
Total dots
Move the arrow to
the item and press
POINT RIGHT /
LEFT button.
The number of the total dots in one horizontal period. Adjust the
number to match your PC image.
White balance (Red / Green / Blue)
Move the arrow to the color that you want to adjust. Press POINT
LEFT button to lighten the color and press POINT RIGHT button to
deepen the color. (From 0 to 63.)
Contrast
Close the PICTURE
IMAGE ADJUSTMENT
Menu.
Press POINT LEFT button to decrease contrast, and press POINT
RIGHT button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust the image darker, and press
POINT RIGHT button to adjust brighter. (From 0 to 63.)
Each of the keys operates as follow.
Reset
Stored
Quit
Recalls the data previously adjusted.
Stores the adjusted data in the memory.
Closes the PICTURE IMAGE ADJUSTMENT Menu.
NORMAL FUNCTION
The normal picture level is preset on this projector at the factory and
can be restored anytime you press the NORMAL button (located on
the Top Control or on the Remote Control Unit). The “Normal”
display will be displayed on the screen for a few seconds.
Normal
26
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
AUTO IMAGE FUNCTION
The Auto Image function is provided to automatically adjust Fine
sync., Total dots, and Picture Position for most computers.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
AUTO IMAGE
and press the SELECT button.
Another dialog box AUTO IMAGE Menu will appear.
Move the arrow to an item that you want to adjust by pressing
the POINT UP/DOWN button. Change the setting On or Off by
pressing the SELECT button.
2
Fine sync.
Adjust the picture as necessary to eliminate flicker from the display.
This item can be adjusted manually. (Refer to page 26.)
Total dots
The number of the total dots in one horizontal period. This item can
be adjusted manually. (Refer to page 26.)
Starts the adjustment
on the item set to "On".
Position
Move the arrow to
the item and then
press the SELECT
Adjustment of the position of the image. This item can be adjusted
manually. (Refer to page 27.)
Terminates the PICTURE
IMAGE ADJUSTMENT Menu.
button.
Move the arrow to “Go!” and press the SELECT button to start
the Auto Image function.
This adjustment can be executed by pressing AUTO IMAGE
button on the Top Control and the Remote Control Unit.
3
Stored
Stores the On/Off setting of each item.
Starts the Auto Image Adjustment.
Go!
Quit
Closes the AUTO IMAGE ADJUSTMENT Menu.
NOTE : The Fine sync., Total dots, and Picture Position of some
computers may not be fully adjusted with the Auto Image
Function. In that case, manual adjustment is required to
make fine image. (Refer to page 26 to adjust "Fine sync." or
"Total dots" and page 27 to adjust Picture Position.)
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
POSITION
and press the SELECT button. The PICTURE
POSITION dialog box will appear.
Move the image by pressing the POINT UP / DOWN / RIGHT /
LEFT buttons.
PICTURE POSITION
dialog box
2
Press the POINT UP
/
DOWN / RIGHT / LEFT
buttons to move the image
27
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
SCREEN
and press the SELECT button. Another dialog
box PICTURE SCREEN Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the function that you want to select
and then press SELECT button.
2
True
Move the arrow to the
function and press the
SELECT button.
To make the image into its original size select True in the dialog
box. When the original image size is larger than the screen size
(800 x 600), this projector enters Digital Zoom mode automatically.
Keystone
When the image is distorted vertically, select Keystone in the dialog
box. The ON-SCREEN menu and SCREEN ADJUST menu
disappears and the message “Keystone” is displayed. Correct the
Keystone distortion by pressing the KEYSTONE ●/● button or the
POINT UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT
on page 20.
Digital Zoom
To adjust the image size or pan the image, select Digital zoom in
the dialog box. The ON-SCREEN menu and SCREEN ADJUST
menu disappears and the message “D. Zoom” is displayed.
This projector is also enters Digital Zoom mode by pressing the
D.ZOOM ●/● button on the Remote Control Unit.
Refer to the following for operation.
Expand function
To expand the image size, press the D.ZOOM ● button or the SELECT button. The image is magnified by degrees.
Compress function
To compress the image size, press the D.ZOOM ● button or the RIGHT CLICK button. The size of image is reduced by
degrees.
Panning function
To pan the image, press the POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image
is larger than the screen size.
To cancel Digital Zoom mode, press any button except D.ZOOM ●/●, SELECT, RIGHT CLICK, POINT or LASER
button. To adjust the image to 800 x 600, press NORMAL button.
● This projector cannot display any resolution higher than 1024 X 768. If your computer’s screen resolution is higher
than 1024 X 768, reset the resolution to the lower before connecting the projector.
● The image data in other than SVGA (800 x 600) is modified to fit the screen size in the initial mode.
● The normal "Panning Operation" may not function properly if the computer system prepared with the "PC Adjust" is
used.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
SELECTING VIDEO MODE
DIRECT OPERATION
MODE button
COMPUTER
Select VIDEO mode by pressing the MODE button on the Top
Control or the VIDEO button on the Remote Control Unit.
VIDEO
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Video
press the SELECT button.
and
SELECTING COLOR SYSTEM
Press the MENU button and the ON-SCREEN MENU will
This box indicates the
system being selected.
1
2
appear. Press the POINT LEFT/RIGHT buttons to select
SYSTEM and press the SELECT button. Another dialog box
VIDEO SYSTEM Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to "Auto", and then press the
SELECT
button.
Auto
The projector automatically detects the incoming Video system, and
adjusts itself to optimize its performance.
When the Video System is PAL-M or PAL-N, select the system
manually.
Move the arrow to
the Mode and press
the SELECT button.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If the projector cannot reproduce the proper video image, it is
necessary to select a specific broadcast signal format among PAL,
SECAM, NTSC, NTSC 4.43, PAL-M, or PAL-N.
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
SCREEN
and press the SELECT button. Another dialog
box PICTURE SCREEN ADJUSTMENT DISPLAY will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the screen size that you want to
2
set, and then press the
SELECT button.
Regular
Normal Video Image size with 4 x 3 aspect ratio.
Move the pointer to the function and
press the SELECT button.
Wide
Resizes the image for wide screen size with 16 x 9 aspect ratio.
Keystone
When the image is distorted vertically, select Keystone in the dialog
box. Correct the Keystone distortion by pressing KEYSTONE ●/●
button or POINT UP/DOWN button(s). Refer to KEYSTONE
ADJUSTMENT on page 20.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
PICTURE IMAGE ADJUSTMENT
ADJUSTING THE PICTURE IMAGE
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
IMAGE and press the SELECT button. Another dialog box
1
2
PICTURE IMAGE ADJUSTMENT Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to adjust by
pressing the POINT UP/DOWN buttons. To change the value,
press either the POINT RIGHT button or the POINT LEFT
button.
Color
Indicates the level
of the item.
Press POINT LEFT button to lighten the image, and press POINT
RIGHT button to deepen the image. (From 0 to 63.)
Move the arrow to
the item and press
POINT RIGHT /
LEFT button.
Tint
Press POINT LEFT button to increase purple, and press POINT
RIGHT button to increase green. (From 0 to 63.)
White balance (Red / Green / Blue)
Move the arrow to the color that you want to adjust. Press POINT
LEFT button to lighten the color, and press POINT RIGHT button to
deepen the color. (From 0 to 63.)
Contrast
Closes the PICTURE
IMAGE ADJUSTMENT
Menu.
Press POINT LEFT button to decrease contrast, and press POINT
RIGHT button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to darken the image, and press POINT
RIGHT button to brighten the image. (From 0 to 63.)
Sharpness
Press POINT LEFT button to soften the image, and press POINT
RIGHT button to sharpen the image. (From 0 to 63.)
Each of the keys operates as follow.
Reset
Stored
Quit
Recalls the data previously adjusted.
Stores the data in the memory.
Closes the PICTURE IMAGE ADJUSTMENT Menu.
NORMAL FUNCTION
The normal picture level is preset on this projector at the factory and
can be restored anytime you press the NORMAL button (located on
the Top Control or on the Remote Control Unit). The "Normal"
display will be displayed on the screen for a few seconds.
Normal
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
SETTING MENU
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
SETTING and press the SELECT button. Another
dialog box SETTING Menu will appear.
1
2
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to set, and
then press the
SELECT button to set it "On" or "Off".
When this function is in the "On" position, this projector
will produce a blue image instead of the video noise on
the screen when the input source is unplugged or
turned off.
Blue back
When this function is in the "On" position, the On-
Screen Displays always appear when adjustments are
made. (The following displays disappear by switching
this function "Off.")
Display
Set the Pointer to the item,
and then press the SELECT
button.
● Preparation Display
(The Number-counting-down Display)
● Mode Display
● Volume/Mute Display
● Zoom Display
● Focus Display
● Normal Display
● No show Display
● Keystone Display
● D.Zoom Display
Ceiling function
Rear function
When this function is in the “On” position, the top /
bottom and the left / right reversed picture is provided
to project the image from a ceiling mounted projector.
Ceiling
Rear
When this function is in the “On” position, the left / right
reversed picture is provided to project the image to a
rear projection screen.
Turn this function “On” in the SETTING menu. The
picture will change into next one by sliding black image
side ways like drawing the black curtains when the
input source is changed.
Split wipe
The Lamp age function is designed to reset the lamp
replacement monitor timer. When replacing the lamp,
reset the lamp replacement monitor timer by using this
function. (Refer to page 34.)
Lamp age
SELECTING LANGUAGE
The language used in the ON-SCREEN MENU is selectable from
among English, German, French, Italian, Spanish and Japanese.
Press the MENU button and the ON-SCREEN MENU will
appear. Press POINT LEFT/RIGHT buttons to select
LANGUAGE and press the SELECT button. Another dialog
box LANGUAGE Menu will appear.
1
Move the Pointer to the
language that you want
to set, and then press
the SELECT button.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the language that you want to set,
2
and then press the
SELECT button.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
OPERATING WIRELESS MOUSE
The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse
for most Personal Computers. The POINT buttons and the two CLICK buttons are used for the wireless mouse
operation.
The wireless mouse is available only when PC mouse pointer is displayed on the screen. When the menu or
the indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse
cannot be used.
INSTALLATION
To use the Wireless Remote Control Unit as the Wireless Mouse for a Personal Computer, installation of the
mouse driver (not supplied) is required. Make sure that the mouse driver is properly installed in your
computer. And make sure that the mouse port of the computer connected to Control Port is activated.
Connect the mouse port of your computer to the Control Port of
the projector with the Control Cable. (Refer to page 10 to 13 for
connection.)
1
Note : When the computer has no
mouse port, connect the Serial
Port of the computer to Control
Port of the projector with the
Control Cable for Serial Port.
Turn the projector on first, and then turn on your computer.
When the computer is switched on first, the Wireless Mouse
may not work properly.
2
OPERATING WIRELESS MOUSE
When controlling the pointer of the computer, operate the Wireless Mouse with POINT button, SELECT
button, and RIGHT CLICK button on the Wireless Remote Control Unit.
POINT button (Move the pointer)
POINT button
Used to move the pointer. The pointer is moved corresponding with
the direction you are pressing.
SELECT (LEFT CLICK) button
This button has the same function as the left button in a PC mouse.
RIGHT CLICK button
This button has the same function as the right button in a PC mouse.
Pressing this button does not affect any operation when in Menu
mode.
SELECT button
(left button of the
mouse)
RIGHT CLICK button
(right button of the mouse)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MAINTENANCE
TEMPERATURE WARNING INDICATOR
The TEMPERATURE WARNING Indicator flashes red when the internal temperature of the projector exceeds
the normal temperature. The Indicator stops flashing when the temperature of the projector become normal.
When the TEMPERATURE WARNING Indicator continues to flash, check the item listed below.
The Ventilation slots of the projector may be blocked. In such an event, reposition the appliance so that the
ventilation slots are not obstructed.
1
Air filters are clogged with dust particles. Clean the air filters by following AIR FILTER CARE AND CLEANING
below.
2
If the TEMPERATURE WARNING Indicator remains on after performing the above checks, the Cooling Fans or the
Internal Circuits may be malfunctioning. In that case, call Boxlight.
3
AIR FILTER CARE AND CLEANING
The Removable Air Filters prevent dust from accumulating on the surface of the Projection Lens and the
Projection Mirror. Should the Air Filters become clogged with dust particles, it will reduce the Cooling Fans'
effectiveness and may result in internal heat build up and adversely affect the life of the projector.
Clean the Air Filters following the steps below:
Turn the power off, and disconnect the AC power cord from the
AC outlet.
AIR FILTERS
1
Turn the projector upside down and remove the Air Filters by
pulling the latches upward.
2
Clean the Air Filters with brush or wash out the dust and
particles.
3
Replace the Air Filter. Make sure that the Air Filters are fully
inserted.
4
CAUTION
Do not operate the projector with the Air Filter removed.
Dust may become stuck on the LCD Panel and the Mirror
degrading picture quality.
Do not put small parts into the Air Intake Vents. It may
result in malfunction of the projector.
The Air Filter is small part. Ensure that children don’t eat
or swallow it.
RECOMMENDATION
We recommend avoiding dusty/smoky environment for operating the projector. Using in these
environment may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on the liquid crystal panel and lens inside it, and may
resultantly be projected onto the screen together with the picture.
When the above symptoms are noticed contact Boxlight at 1-800-762-5757 or 360-779-7901 for cleaning.
CLEANING THE PROJECTION LENS
Follow these steps to clean the projection lens:
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of
cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
1
Lightly wipe the cleaning cloth over the lens.
2
3
When the projector is not in use, replace the lens cover.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACEMENT INDICATOR
When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights
yellow. When the image becomes dark or the color of the image becomes unnatural, replacement of the
Lamp is required.
LAMP REPLACEMENT
CAUTION
● For continued safety, replace with a lamp assembly of the same type.
● Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector
can become very hot.
● Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.
Follow these steps to replace the lamp assembly.
Turn off the projector and disconnect the AC plug. Allow the
projector to cool for at least 45 minutes.
1
Remove a screw with a screwdriver and remove the Lamp
Cover.
2
Remove 2 screws with a screwdriver and pull out the Lamp
Assembly by grasping the handle.
3
LAMP COVER
Replace the Lamp Assembly with new one and tighten 2
4
screws. Make sure that the Lamp Assembly is set properly.
And replace the Lamp Cover and tighten a screw.
HANDLE
Connect the AC Power Cord to the projector and turn the
projector on.
5
Reset the Lamp Replacement Monitor Timer (refer to the
section “Lamp Replacement Monitor Timer” below).
6
NOTE : Do not reset the LAMP REPLACEMENT MONITOR
LAMP
ASSEMBLY
TIMER, when the lamp is not replaced.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through Boxlight at 1-800-762-5757 or 360-779-7901.
● Model No. of your projector : BOXLIGHT CP-11t
● Replacement Lamp Type No. : POA-LMP21J
(BOXLIGHT Lamp No. : CP10T-930)
(Service Parts No. 610 280 6939)
LAMP REPLACEMENT MONITOR TIMER
Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the
Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.
Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT
1
LEFT/RIGHT buttons to select SETTING
dialog box SETTING MENU will appear.
and press the SELECT button (refer to the page 31). Another
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to Lamp age, and then press the
SELECT button. The message "Lamp replace monitor Reset?" is displayed.
2
3
Select [Yes] to reset the Timer.
Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service station for assistance, check the matters below once again.
1. Make sure you have connected the projector to your equipment as described in the section "CONNECTING
THE PROJECTOR" on pages 10 ~ 13.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce the image, re-start the computer.
5. If the image sill does not appear, unplug the projector from the computer and check the computer monitor's
display. The problem may be with your graphics controller rather than with the projector. (When you
reconnect the projector, remember to turn the computer and monitor off before you power up the projector.
Power the equipment back on in order of : Projector and computer.)
6. If the problem still exists, check the following chart.
Problem:
No power.
Try these Solution
● Plug the projector into the AC outlet.
● Be sure READY Indicator light is On.
● Wait 90 seconds after the projector is turned OFF before turning the projector back on.
NOTE : After pressing the power ON-OFF switch to OFF, make sure the projector works
as follows:
1. The LAMP indicator will light and the READY indicator will turn off.
2. After 90 seconds, the READY indicator will light green again and the projector
may be turned on by pressing the power ON-OFF button.
● Check the TEMPERATURE WARNING indicator. If the indicator flashes red, the
projector cannot be turned on.
(See "TURNING ON/OFF THE PROJECTOR" section on page 19.)
● Check the Projection Lamp. (Refer to page 34.)
● Adjust the focus
Image is out of
focus.
● Make sure the projection screen is at least 4.6’ (1.4m) from the projector.
● Check the projection lens to see if it needs cleaning.
NOTE : Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on the lens. In such an event, leave
the projector OFF an d wait until condensation disappears.
● Check Ceiling / Rear feature. (See “SETTING” section on page 31.)
● Check Ceiling feature. (See “SETTING” section on page 31.)
Picture is Left/Right
reversed.
Picture is
Top/Bottom
reversed.
● Check Display feature.(See “SETTING” section on page 31.)
Some displays are
not seen during the
Operation.
● Check the connection between the computer or video equipment and the projector.
● When turning the projector on, it takes about 30 seconds to display the image.
● Check the system that you select is corresponding with the computer or the video
equipment.
No image.
● Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).
● Check audio cable connection from audio input source.
● Adjust the audio source.
No sound.
● Press VOLUME (+) button.
● Press MUTE button.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Problem:
Remote Control Unit
does not work.
Try these Solution
● Check the batteries.
● Check the ALL-OFF switch on the Remote Control Unit is set to “ON.”.
● Make sure nothing is between the Remote Receiver and the Remote Control Unit.
● Make sure you are not too far from the projector when using the Remote Control Unit.
Maximum operating range is 16.4’ (5m).
● Check the cable connection between the projector and the computer.
● Check the mouse setting on your computer.
● Turn the projector on before you turn on the computer.
Wireless Mouse
function does not
work.
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
Boxlight Service is easily obtained. If after following instructions above, you find that service is necessary,
contact Boxlight for assistance at 1-800-762-5757 or 360-779-7901.
Give the model number and explain the difficulty. We will advise you how to obtain service.
Please have the following information available.
● Serial No. of projector.
● Resolution of the computer.
● Refresh rate of computer.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
Multi-media Projector
Projector Type
(not including Adjustable Feet)
9.41" x 3.54" x 12.72" (239mm x 90mm x 323mm)
8.6 lbs (3.9 kg)
(W x H x D)
Dimensions
Net Weight
0.9" TFT Active Matrix type, 3 panels
800 x 600 dots
LCD Panel System
Panel Resolution
Number of Pixels
Color System
1,440,000 (800 x 600 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 30” to 300”
Scanning Frequency
Projection Image size
Horizontal Resolution
Projection Lens
Throw Distance
(Diagonal)
750 TV lines
F 1.7 ~ 2.0 lens with f 33.2mm ~ 43.1mm Motor zoom and focus
4.6’ ~ 35.4’ (1.4 m ~ 10.8 m)
150 W
Projection Lamp
AV Input Jacks
RCA Type x 1 (Video, Audio R and L) and DIN 4 pin (S-Video) x 1
(VGA) HDB 15 Terminal x 1
DIN 8 pin x 1
Computer Input Jacks
Control Port Jack
Monitor Output Jack
(VGA) HDB 15 Terminal x 1
Mini Jack (stereo)
Computer Audio Input Jack
Audio Output Jack
Internal Audio Amp
Built-in Speaker
Mini Jack (stereo)
1W RMS (Monaural)
1 speaker, 1.57" x 1.18" (40mm x 30mm)
0˚ to 10˚
Feet Adjustment
AC 100 ~ 120 V / 200 - 240 V, 50 / 60 Hz
2.5 A / 1.4 A (Max. Ampere)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Voltage
Power Consumption
Operating Temperature
Storage Temperature
Remote Control Transmitter
Power Source
Operating Range
Dimensions
:
:
:
:
:
AA Type x 2
16.4’ (5m) / ±30˚
2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
0.35 lbs (160 g) (including batteries)
Net Weight
(Max. Output : 1mW / Wave length : 650±20nm)
Class II Laser
Laser Pointer
Owner’s Manual
Accessories
AC Power Cord
Remote Control Transmitter and Batteries
VGA Cable
Control Cable for PS/2 port
Dust Cover
Lens Cover
● The specifications are subject to change without notice.
This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It
is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty
and electrical hazards.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
BOXLIGHT CORPORATION (“BOXLIGHT”) warrants that each Boxlight CP-11t (“the Product”) sold hereunder will
conform to and function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply
only to the first person or entity that purchases the Product for personal or business use and not for the purpose of
distribution resale. Said warranty shall continue for a period of two (2) years from the date of such purchase.
BOXLIGHT does not warrant that the Product will meet the specific requirements of the first person or entity that
purchases the Product for personal or business use. Lamp is warrantied for 120 days.
BOXLIGHT CORPORATION’s liability for the breach of the foregoing limited warranty is limited to the repair or
replacement of the Product or refund of the purchase price of the Product, at BOXLIGHT’s sole option. To exercise
the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and
expense, to BOXLIGHT or any authorized service center provided, however, that the Product must be accompanied by
a written letter explaining the problem and which includes (i) proof of purchase; (ii) the dealer’s name; (iii) the model
and serial number of the Product. A return authorization number, issued by the BOXLIGHT customer service
department, must also be clearly displayed on the outside of the shipping carton containing the Product.
WARRANTY LIMITATION AND EXCLUSION
BOXLIGHT CORPORATION shall have no further obligation under the foregoing limited warranty if the Product has
been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized
modification, tampering, alterations, or service other than by BOXLIGHT or its authorized agents, causes other than
from ordinary use or failure to properly use the Product in the application for which said Product is intended.
DISCLAIMER OR UNSTATED WARRANTIES
The warranty printed above is the only warranty applicable to this purchase.
All other warranties express or implied, including, but not limited to, the implied warranties or merchantability and
fitness for a particular purpose are disclaimed. There are no warranties that extend beyond the face of hereof and the
foregoing warranty shall not be extended, altered or varied except by written instrument signed by BOXLIGHT
CORPORATION.
LIMITATION OR LIABILITY
It is understood and agreed that BOXLIGHT’s liability whether in contract, in tort, under any warranty, in negligence or
otherwise shall not exceed the return of the amount of the purchase price paid by purchaser and under no
circumstances shall BOXLIGHT be liable for special, indirect or consequential damages. The price stated for the
Product is a consideration in limiting BOXLIGHT’s liability. No action regardless of form, arising out of the agreement
to purchase the product, may be brought by purchaser more than one year after the cause of action has accrued.
Boxlight
19332 Powder Hill Place
Poulsbo, WA 98370-7407 USA
USA and Canada 800-762-5757
International 360-779-7901
Printed in Japan
Part No. 610 288 3893 (1AA6P1P2481-- MA6E)
Download from Www.Somanuals.com. All Manuals Search And Download.
|