TRAVEL bag INSTRUCTIONS
Fax: (208) 375-5172, BOB Trailers, Inc. 5475 Gage St. Boise, Idaho 83706
Congratulations on your purchase of the BOB Travel Bag. It is
A6. Locate fork dropout
protector and confirm it is
attached securely to end of
small red webbing as shown
in Fig. C. The fork dropout
protector can be replaced
easily if lost or damaged with
most other common fork
dropout protector(s) used on
strollers and bicycles for
shipping, available through
your bicycle or stroller dealer.
Pocket Seam
designed to contain and protect your single seat BOB Sport Utility,
Revolution or Stroller Strides stroller during transport. The Travel Bag
may be rolled and guided by the end handle or carried via shoulder
strap and/or side handle. The Travel Bag will need to be assembled
prior to use.
Notch
Insert
Notch
Before attempting to assemble or use your new Travel Bag, read
and understand these instructions to ensure proper assembly
and operation. If you are unclear on any point, contact your dealer
or BOB before use.
fully up
to Seam
WARNINGS
Use Instructions:
Fig. B: Panel ends into corner
pockets (right side shown).
.
This product is designed exclusively for use with BOB single Sport
Utility, Revolution or Stroller Strides strollers. It is not intended for
use with any other strollers or products.
U1. Prepare Travel Bag: Zip
Travel Bag zipper completely
open and fold top cover over,
exposing pockets for Front
Wheel and Front Wheel
Quick Release (QR). Locate
center strap and unfasten
side release buckle. Place
center strap ends outboard
of Travel Bag as shown in
Fig. 1.
.
When not in use, keep out of reach of children.
.
Maximum Weight Capacity 30lb (13.6Kg) Do not overload.
.
Never leave child unattended.
.
The Travel Bag is designed to reduce the possibility of damage to
your stroller during transportation but does not eliminate it completely.
.
We recommend inspecting your Stroller and Travel Bag before and
after each transport journey to ensure functionality and safety.
Assembly Instructions:
A1. Remove bag from packaging. Place bag flat on ground or table
with wheels down. Open Travel Bag top cover zipper and locate
components. Fig. A identifies the anatomy and components of the
Travel Bag.
U2. Prepare stroller to place
in Travel Bag. Remove
contents from stroller
(occupant and all contents of
Low Boy luggage pouch).
Remove stroller rear wheels.
Close rear wheel QR’s. (See
Rear Wheel section of your
stroller’s owner’s manual).
A2. Unfasten the Velcro of the five Fabric Flaps along inboard sides
of travel bag. Temporarily place top of each over side and out of the
way as shown in Fig. A.
Fig. C: Fork Dropout Protector
shown properly attached.
A3. Locate wall support panel, (black plastic sheet) unroll and note
orientation of notch at each end.
U3. Remove Front Wheel
from stroller (See Front
Wheel section of your
Center Strap
open w/ends
outboard
A4. Orient wall support panel with notches toward top cover (up)
and feed each end into each respective pocket along inside corners
of Travel Bag as shown in Fig B. Push ends of wall support panel
fully into each pocket until notch is aligned with pocket seam.
stroller’s owner’s manual).
Remove Front QR from Front
Wheel. Reassemble Front
QR components in proper
orientation as shown in Fig.
2, and place inside the gray
pocket located inside top
cover of Travel Bag. Locate
black plastic axle protectors
at ends of red straps inside
large front wheel pocket.
Push hollow end of each
plastic axle protector fully
over each end of Front Wheel
axle as shown in Fig. 3.
Place Front Wheel into
A5. Align and fasten Velcro of fabric flaps straight and secure around
wall support panel. You may find it helpful to bend the support panel
top edge slightly inboard while the Velcro of each fabric flap is secured.
Top
Cover
Open
Zippered Top Cover
Wall Support Panel (rolled up)
Fig. 1: Travel Bag fully assembled
and prepared for stroller.
Front
Wheel
Pocket
pocket inside top cover and
fasten Velcro closures.
Center Strap
& Buckle
Front QR
Pocket
Cam Housing
U4. Place rear wheels inside
Travel Bag with stub axles
facing up. Position stroller
wheels along center line as
far back towards base of bag
as possible, leaving extra
space for fork protector, as
shown in Fig. 4.
Fork Protector
& Strap
Fabric Flaps
(open)
Conical
Springs
Rod
QR
Shoulder
Strap
Lever
U5. For Sport Utility Stroller
(fixed wheel) models, close
Caliper Brake Quick Release
Lever after removing wheel,
as stroller will fold more
Adjusting Nut
Handles
Fig. A: Anatomy of the BOB Travel Bag.
Fig. 2: Front QR anatomy
shown properly assembled.
OMA17A
P1
Download from Www.Somanuals.com. All Manuals Search And Download.
|