Infant Car Seat
Adapter Instructions
BOB Stroller Model Year Compatibility
Congratulations on your
purchase of the BOB Infant
Car Seat Adapter (ICSA).
It is designed to allow the
attachment of an Infant
Car Seat to your BOB
Stroller. Please refer to the
tables at right for details
of compatible strollers and
car seats.
Model Year(s)
Model
Serial Number
2005 and newer
2005 and newer
2005 and newer
2005 and newer
2005 and newer
2007 and newer
Sport Utility Stroller
Sport Utility Stroller D’Lux
Ironman
AA000001 and higher
AB000001 and higher
AC000001 and higher
AF000001 and higher
AG000001 and higher
AK000001 and higher
Revolution
Stroller Strides
Revolution 12”
Car Seat Compatibility
Model
Brand
Year(s)
Britax®
Graco®
Graco®
Peg Pérego®
Peg Pérego®
Companion®
Snug Ride®
SafeSeat™
Primo Viaggio®
Primo Viaggio SIP™
2003 and newer
2003 and newer
2006 and newer
2003 and newer
2006 and newer
Tray
Long Screw
(installed)
Arm
Short Screw
(installed)
Long Screw (installed)
Arm
Accessory Bar
Short Screw
(installed)
Pivot Nut 2x
Pivot Screw 2x
Pivot Plug 2x
Sharp Screw 2x
Main Bar
Restraint
Belt F
Restraint
Belt M
TOOLS NEEDED:
Phillips screwdriver.
TAKE TIME - READ AND UNDERSTAND INSTRUCTIONS COMPLETELY!
Before attempting to assemble or use your new ICSA, read and understand these assembly
instructions completely, as well as the warnings at the end of this document, to insure proper
assembly and safe operation.
If you are unclear on any point, contact your dealer or BOB before use.
OMA09D
P1
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACH RESTRAINT BELT M/F AND ARMS
LOCATE FABRIC SCREWS
REMOVE FABRIC SCREW
Extend canopy to expose
lower fabric screw.
Remove screw with
Phillips screwdriver,
exposing fabric
grommet and
rivet nut.
Repeat on other side.
ATTACH RESTRAINT BELT M
POSITION ARM
POSITION RESTRAINT BELT M
Slide restraint belt M grommet between
end of arm and fabric grommet.
Position arm between canopy and frame.
Align arm hole over
fabric grommet
and rivet nut.
Red pull ring
should face out.
TIGHTEN SHARP SCREW
INSERT SHARP SCREW
Hold strap at a 90
degree angle.
Insert sharp screw through end of
arm, restraint belt grommet, fabric
grommet and into rivet nut.
90°
Tighten firmly with
Phillips screwdriver.
Note:
If screw does not turn easily,
unscrew and start again.
OMA09D
P3
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACH RESTRAINT BELT F
BUCKLE BELT
POSITION ARM
POSITION RESTRAINT BELT F
Slide restraint belt F
grommet between end of
arm and fabric grommet.
Position arm between canopy
Connect restraint belt F
to restraint belt M.
and frame.
Align arm hole over fabric
grommet and rivet nut.
INSERT SHARP SCREW
TIGHTEN SHARP SCREW
Hold strap at a 90 degree angle.
Insert sharp screw through end of
arm, restraint belt grommet, fabric
grommet and into rivet nut.
90°
Tighten firmly with
Phillips screwdriver.
Note:
If screw does not turn easily,
unscrew and start again.
PREPARE STROLLER FOR INFANT CAR SEAT INSTALLATION
SET PARKING BRAKE
POSITION CANOPY
UNBUCKLE
RESTRAINT BELT
See the “Parking Brake”
section of your stroller
owner’s manual.
Position canopy
against handle bar.
Unbuckle restraint belt.
Place ends outside seat.
OMA09D
P4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL INFANT CAR SEAT
When installing car seat in the ICSA for the first time, test fit with
the car seat unoccupied to ensure you understand the process.
Installing occupied Infant Car Seat on ICSA for first time may result
in accident, serious injury or death.
Warning
®
®
®
Britax Go To
Peg Pérego Go To
Graco Go To
®
Britax
POSITION
CAR SEAT
LOWER SEAT BACK
RAISE HANDLE
Place car seat
“rear facing”onto
ICSA accessory
bar, in a straight
downward
motion.
Lower seat back 7”to 8”.
See “Reclining Seat”
section of your stroller
owner’s manual.
Move car seat
handle into upright
carrying position.
ENGAGE CAR SEAT
FASTEN RESTRAINT BELT
TIGHTEN RESTRAINT BELT
Slide grooves on
underside of car seat
onto ICSA accessory bar.
Fasten restraint belt over top
of infant car seat as shown.
Pull on red ring
to tighten.
Warning
Be sure restraint belt tension is not
constricting child as it may cause
serious injury.
DOUBLE CHECK CAR SEAT IS SECURELY ATTACHED
Pull car seat upward without
Warning
®
TO REMOVE Britax
removing restraint belt.
Failure to securely attach
car seat may result in
serious injury or death.
You should not be able to
remove car seat without
unfastening restraint belt.
Go To
OMA09D
P5
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Peg Pérego
RAISE SEAT BACK
POSITION CAR SEAT
POSITION HANDLE
See the “Reclining Seat”
section of your stroller
owner’s manual.
Move car seat handle
into upright carrying
position.
Place car seat
“rear facing”
onto ICSA
accessory bar,
in a straight
downward
motion.
ENGAGE CAR SEAT
FASTEN RESTRAINT BELT
Fasten restraint belt
over top of infant car
seat as shown.
Slide grooves on
underside of car
seat onto ICSA
accessory bar.
DOUBLE CHECK CAR SEAT
IS SECURELY ATTACHED
TIGHTEN RESTRAINT BELT
Pull on red ring to tighten.
Pull car seat upward without
removing restraint belt.
You should not be able to
remove car seat without
unfastening restraint belt.
TO REMOVE
®
Peg Pérego
Go To
Warning
Failure to securely
attach car seat may
result in serious injury
or death.
Warning
Be sure restraint belt tension is not
constricting child as it may cause
serious injury.
OMA09D
P6
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Graco
RAISE SEAT BACK
REMOVE ACCESSORY BAR
See the “Reclining Seat”
section of your stroller
owner’s manual.
Using a Phillips screwdriver,
remove both screws.
TIP: Attach short screws to
accessory bar for future use.
CAUTION: Ends of accessory bar are sharp!
POSITION HANDLE
POSITION CAR SEAT
Move car seat handle into
upright carrying position.
Place car seat “rear
facing”onto ICSA
main bar, in a straight
downward motion.
ENGAGE CAR SEAT
FASTEN RESTRAINT BELT
Slide grooves on underside of
car seat onto ICSA main bar.
Fasten restraint belt over top of
infant car seat as shown.
Red hook on Graco®
should be under
main bar.
OMA09D
P7
Download from Www.Somanuals.com. All Manuals Search And Download.
DOUBLE CHECK CAR SEAT
IS SECURELY ATTACHED
TIGHTEN RESTRAINT BELT
Pull on red r
Pull car seat upward without removing
restraint belt.
You should not be able to remove
car seat without unfastening restraint belt.
Be sure restraint
belt tension is not
constricting child as it
may cause serious injury.
Failure to securely attach car seat
may result in serious injury or death.
®
TO REMOVE Graco Go To
TO REMOVE CAR SEAT
SET PARKING BRAKE
UNFASTEN RESTRAINT BELT
See the “Parking Brake”
section of your stroller
owner’s manual.
Unfasten restraint
belt. Place ends
outside seat.
FASTEN RESTRAINT BELT
REMOVE CAR SEAT
Fasten restraint belt
when not in use.
®
Britax
Peg Pérego
®
With car seat handle
in upright position,
lift car seat straight
up and off ICSA bar.
®
Graco
With car seat handle
in upright position,
squeeze red release
®
button under Graco
car seat canopy, lift
car seat straight up
and off ICSA bar.
OMA09D
P8
Download from Www.Somanuals.com. All Manuals Search And Download.
TRAY INSTALLATION
REMOVE ACCESSORY BAR
Children should not be
placed directly in the
BOB Stroller seat with
the ICSA installed, unless
tray is installed for
Using a Phillips screwdriver,
remove both screws.
TIP: Attach short screws to
accessory bar for future use.
safety and protection.
CAUTION: Ends of accessory bar are sharp!
REMOVE SCREWS
ENGAGE TRAY
Hook tray onto
main bar.
Using a Phillips screwdriver,
remove long screws from tray.
SECURE TRAY
ROTATE TRAY
Rotate tray towards stroller seat
until it rests on main bar.
Insert long screw through each hole in tray,
main bar and into nut on underside of tray.
Tighten firmly with Phillips screwdriver.
Line up holes.
OMA09D
P9
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE RESTRAINT BELT M
POSITION ARM
REMOVE SHARP
SCREW AND BELT
Position arm between
canopy and frame.
Using a Phillips
screwdriver, remove
sharp screw and
restraint belt M.
Align arm hole over
fabric grommet and
rivet nut.
REPLACE SHARP SCREW
TIGHTEN SHARP SCREW
Insert sharp screw
through end of arm,
fabric grommet and
into rivet nut.
Tighten firmly with
Phillips screwdriver.
Note:
If screw does not
turn easily, unscrew
and start again.
REMOVE RESTRAINT BELT F
REMOVE SHARP
SCREW AND BELT
POSITION ARM
Position arm
between canopy
and frame.
Align arm hole over
fabric grommet and
rivet nut.
Using a Phillips
screwdriver, remove
sharp screw and
restraint belt F.
TIGHTEN SHARP SCREW
REPLACE SHARP SCREW
Tighten firmly with
Phillips screwdriver.
Insert sharp screw
through end of arm,
fabric grommet and
into rivet nut.
Note:
If screw does not
turn easily, unscrew
and start again.
OMA09D
P10
Download from Www.Somanuals.com. All Manuals Search And Download.
Infant Car Seat Adapter Warnings
• The BOB Infant Car Seat Adapter is designed
• Follow assembly instructions. Failure to
properly install this accessory product may
result in accidents, severe injury or death.
If you are not sure you can properly install
this accessory, contact your BOB retailer and
arrange for them to perform the installation.
for use with single seat BOB Strollers and
compatible Infant Car Seats. This product is
not a universal adapter. Do not use with car
seats and stroller models other than those
specifically listed in the Stroller and Car Seat
Compatibility charts listed on page 1.
• Never leave children unattended in the
stroller/infant car seat.
• Children should not be placed directly in
the BOB Stroller seat with the ICSA installed,
unless tray is installed directly in front of
child for safety and protection.
• Always secure the infant car seat with the
restraint belt when the car seat is placed in
the stroller. Failure to do so may result in
serious injury or death.
• The ICSA Restraint Belt can interfere with
proper function of the safety harness system.
Additionally, the ICSA Accessory Bar can
interfere with accessibility to the stroller
seat. Therefore, prior to placing child directly
in stroller seat, the ICSA Restraint Belt and
Accessory Bar must be removed from the
stroller AND the Tray must be installed.
Failure to do so may result in serious injury
or death.
• Always keep your Infant Car Seat handle
in the vertical and locked position while in
stroller, as extra protection for your child.
• Stroller may become unstable if parcel bags
are incorrectly attached or if bags other than
those recommended by BOB Trailers, Inc.
are used.
• Do not run or jog when using the ICSA with
car seat installed. Doing so may result in
serious injury or death.
• Read and understand all owner’s manuals
and warnings for all BOB products used with
the ICSA before use.
• Do not use off-road or on uneven terrain
when using the ICSA with car seat installed.
Doing so may cause stroller to become
unstable and result in accident, serious
injury or death.
• Read and understand infant car seat owner’s
manual before use.
• Always use seat harness of Infant Car Seat to
avoid children falling out of stroller.
• Refer to your Infant Car Seat owner’s manual
for maximum capacity limitations and other
safety warnings.
• Children develop at different rates. Consult
with your pediatrician regarding the suit-
ability of the stroller use with your child.
BOB IS NOT RESPONSIBLE FOR INJURY, DAMAGE OR FAILURE THAT RESULTS
FROM OWNERS FAULTY ASSEMBLY OR MAINTENANCE AFTER SHIPPING.
OMA09D
P11
Download from Www.Somanuals.com. All Manuals Search And Download.
BOB is a company that produces high
quality products designed to promote a
healthy outdoor life-style. Go to www.
bobgear.com for our complete line
of products. Before attempting to
assemble or use your new ICSA, read
and understand these instructions
completely to insure proper assembly
and operation.
If you are unclear on any point, contact
your dealer, place of purchase or BOB
[toll free 1-800-893-2447] before use.
A list of dealers is listed on our website
this manual, our warranty and for other
recent product notifications, please visit
B.O.B, B.O.B Logo, and BOB are proprietary
trademarks of BOB Trailers, Inc.
Britax® and Companion® are registered
trademarks of Britax Excelsior Ltd. and
related companies.
Graco® Snug Ride™ and SafeSeat™ are
registered and proprietary trademarks of
Graco Children’s Products, Inc.
Peg Pérego® Primo Viaggio™ and Primo
Viaggio SIP™ are registered and proprietary
trademarks of Peg Pérego S.P.A. Corporation.
LIMITED WARRANTY
BOB Trailers Inc. takes pride in its workmanship and strives to manufacture the best products
possible. Therefore, we warranty the ICSA against defects in material and workmanship subject to
the conditions listed below. Since no product is indestructible, it does not cover defects attributable
to or resulting from normal wear, abuse or alteration.
• Warranty claims must be made through
an authorized dealer.
• The ICSA is warranted for one year
from the date of original purchase.
• This warranty is limited to the repair or
replacement of the defective part. BOB
Trailers, Inc. shall in no event be respon-
sible for consequential or special damages.
• Warranty is only valid for the original
purchaser.
• Proof of purchase is required to
exercise this warranty.
• This Limited Warranty is the only express
or implied warranty applicable to BOB
Trailers, Inc. Any implied warranties,
including warranties of merchantability
and fitness shall be limited in scope and
duration in accordance with this limited
warranty.
• Labor and freight charges are not
included.
• Normal wear, neglect, abuse,
accidents, and improper use are
not covered by this warranty.
OMA09D
P12
Download from Www.Somanuals.com. All Manuals Search And Download.
|