4. At A, insert the web corner pin into the end of the
tent pole ferrule. At B, grasp the tent corner pin in one
hand, the tent pole in the other. Arch the pole and
place the pin into the end of the pole. See Fig 3 & 4.
Repeat this with the second pole from C to D raising the
tent as you go. See fig 5.
7. Attach the fly to the poles. Lay out the fly with the inside side up, on ground at the front of
the tent. Fit the fly poles into the pockets sewn to the hem. The poles run from side to side
down the center of the fly forming an X. Secure the fly to the poles by wrapping the hook &
loop fastener around the fly poles. See fig 9, 10 and 11.
Assembly Instructions
for the N!ergy 1210 Tent
fig 9
Component List:
fig 3
fig 4
1 Tent
2 Tent Poles
1 Carry Bag
1 Rain Fly
6 Pull Out Cords
B
1 Stake Bag W/Stakes
2 Fly Poles
1 Gear Loft
1 Pole Bag
1 Divider
NOTE:
fig 11
• Although it is possible to pitch this tent alone, it is faster/easier with two
people.
fig 10
• Do not drop tent bag or pole bag on its end. Do not bounce tent bag on
its end to get the tent out. These actions may cut the shockcord and/or
damage the pole ends.
• The N!ergy series tents are pre-wired with three 12V outlets. Take care
to keep them in their sleeves and avoid stepping on the sockets and
wires during assembly.
8. Attach the fly to the tent. Turn the fly assembly over and align it so
that the poles point out over the doors. Grasp the corners of the of the
fly and drag them up and over the roof to completely cover the tent.
(This is much easier with two people)
At the corners of the tent, reach under the fly and attach the hook & loop
straps to the tent poles, securing the fly in place. See fig 12.
A
fig 12
At the bottom/corners of the tent, attach the shockcorded J-hooks to the
rings on the corner webs. See fig 13.
fig 13
1. Unroll and unfold the tent on the ground. Separate the rest of the
components and place to one side. Open the door before pitching the
tent. Do not stake the tent down (however, in windy conditions, stake
down one corner that faces into the wind).
fig 5
9. Tie a guy rope to each of the 4
rings attached to the fly and stake
out. Adjust tension with the in-line
sliders. See fig 14 & 15.
D
B
fig 14
5. Start at the bottom and attach all the clips to
the poles to create a freestanding tent. Place it in
the desired location. See fig 6.
A
C
fig 1
2. Assemble all of the shockcorded poles. Keep the end sections from
snapping together, as this can damage the ends. Make certain each
plain end has been properly seated into the metal ferrule.
fig 15
fig 6
fig 7
6. Stake the tent down through the
corner loops. Stake the opposite corners
while applying tension to smooth the
floor wrinkles. Also, stake out the beckett
beneath each of the side windows. See
fig 7 & 8.
YOUR TENT IS READY !
tent poles
fly poles
E! Power System: To use, you will need a power source. Our E! Power Pak™ is sold separately. Once connected to
power, the control will display “green” at any switch that is “ON” and the “ON” socket will glow blue. See fig 16.
E! Power Port: Open zipper and run extension cord through opening.
Close zipper so that it rests next to the extension cord. Make sure the
zipper cover is not twisted or tucked. The cover must lay flat against
the outside of the tent to keep out rain.
blue
3. Insert an assembled pole
through both sleeves from A to
B. Insert the second pole through
the sleeves from C to D, forming
an X across the tent. See fig 1.
There is a fabric loop at the tent’s
peak. Capture this loop with the
top pole as you move through
the sleeves. See fig 1 & 2.
Accessories: E! Power Fan/Light, E! Power Reading Light and an E!
Power 12v Adapter Cord.
green
Sweep Out: Inside, at the bottom of the door is a sewn-in web loop. Pull
this loop to the outside and stake it down to provide a ready exit for
floor sweepings. See fig 17.
fig 16
fig 17
Take Down: Pull up all stakes. Release the fly’s hook & loop straps. Remove fly.
Remove fly poles. Remove clips from tent poles and pull poles off of the pins.
Collapse all poles and stow. Fold the tent onto itself then fold the fly and lay it
on tent. Roll up both towards the open door and stow.
fig 8
REV D 4.09
fig 2
Read the important safety instructions on the reverse side.
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAM SEALING:
CLEANING:
• Clean the tent by setting it up and wiping it down with a mild soap (liquid hand
soap) and lukewarm water solution. Rinse thoroughly and dry completely.
Never use detergent, washing machines or dryers because they can damage
the tent’s protective coating and seams. After cleaning, be sure the tent is
completely dry, especially the heavier, double-stitched areas such as the
seams, before storing or mold / mildew are likely to grow.
• Clean the tent poles with a cloth and lubricate them with silicone spray. This is
especially necessary after ocean side camping to remove salt spray so the
poles don’t corrode or stay gritty.
• Clean the zippers with a quick dip in water and then dry them off. This is
especially important if you’ve been camping in a location with sand/dirt. If you
don’t clean the zippers, the sliders will wear out and eventually the teeth will
become inoperable.
We recommend use of a sealer such as Kenyon Seam Sealer 3 or
McNett Outdoor SeamGrip®.
• Work in a fully ventilated area.
• Set the tent up or lay the tent out flat. Taut seams allow for even
application and penetration of the sealer.
• Decide which seams need to be sealed. Seams that will be exposed
to rain, runoff, or ground level water are a must for sealing, seams on
uncoated nylon or mesh panels don’t need treatment. There is no
need to seal the seams in the roof or the factory taped seams. We
recommend sealing both floor and fly seams and reinforcements.
• Apply sealant to the inside and outside of all exposed seams. Several
thin layers will work better than one thick layer. Read and follow
manufacture’s instructions.
electrocution or electric shock hazard
The use of the Power Port with an extension cord running
in to the tent could result in electrocution or electric shock,
or fire or explosion hazards. For these reasons, when using
the Power Port:
fig.b
fig.a
fig.c
DO NOT allow an extension cord or any electrical device to come into
contact with water or condensation inside the tent.
DO NOT use an extension cord if it is worn or damaged.
CONDENSATION & VENTING:
Through perspiration and breathing, an adult gives off about a pint of water
overnight. If it cannot escape, the water vapor condenses to liquid. Most often,
water found in the tent is a result of this condensation rather than from the tent
leaking. Condensation often forms where the sleeping bag touches the side of
the tent, under the sleeping pad, or on coated surfaces such as the door flaps. A
tent’s double wall construction allows the vapor to escape through the roof to the
outside, keeping the inside of the tent dry.
Leave windows partially open at night to provide cross ventilation and further
reduce condensation. Cross ventilation becomes more important in very humid
or extremely cold conditions when the permeable roof is less effective. The
DO use only extension cords that are marked for OUTDOOR USE.
DO connect extension cord only to a 120Volt GFCI protected outlet with
proper ground. If GFCI outlet is not available, use an extension cord with
GFCI protection built in.
DO make sure the part of the extension cord that is outside the tent is lower
than the power port so that rain will not follow the cord into the tent.
DO follow all warnings, instructions, and safety precautions from the
manufacturer of the extension cord.
To reduce risk of damage to electric plug or cord, pull by the plug rather than
the cord when disconnecting the E! Power Pak from an extension cord.
Your failure to follow these warnings could cause death, serious injury or
permanent disability to you or others. It is always recommended to have
someone nearby to assist in case of an emergency.
ALTERATIONS OR MODIFICATIONS:
STAKING:
DO NOT misuse, modify or alter this product in any way from its condition at the
time of sale. Alteration, modification or any use of this product contrary to the
accompanying written instructions shall void the warranty. Moreover, any
misuse, alteration or modification of the product shall absolve Johnson
Outdoors Gear LLC of any liability for property damages or injuries sustained
as a result of such misuse, modification or alteration.
All tents need to be staked down to keep them from blowing away.
Placing heavy objects inside is just not adequate.
• Once the tent body is erected, stake it out before the fly is put on. This
enables you to square the tent up to ensure that the fly goes on
properly and that the seams align with the frame. Pull the base of the
tent taut between each web stake out loop or ring & pin. Make sure
that all corners are square. It is important that you don’t stake the
tent out too tightly. You will know it’s too tight, if the door zippers can
not be easily operated. Drive stakes through the web loops, or with
ring & pin, drive the stake just outside the ring so that the “J” hook
catches it. Tie a piece of cord or web into a loop through the ring to
be used as a large stake loop if needed.
• With the tent properly staked, drape the fly over the frame, attach its
tent connection points and stake down any pull outs.
• Do not attempt to remove the stakes by pulling on the tent becket
loop, as this could cause the fabric to tear. The best way is to pry on
the stake itself.
features that enhance ventilation are windows, short-sheeted flys (bottom
venting), roof vents, and High/Low venting doors. These are specific to each tent.
-
LIMITED WARRANTY:
What Is Covered: Johnson Outdoors Gear LLC warrants to the original purchaser
that its products are free from defects in material and workmanship, for the life of
the product, except as qualified below. The life of the product is determined from
the date of purchase until such time as the product is no longer serviceable due to
normal wear and tear.
What Is Not Covered: Johnson Outdoors Gear LLC shall not be responsible for the
natural breakdown of materials that occurs inevitably with extended use (e.g., Ultra
Violet (UV) light damage on tents, exhausted zippers), or defects caused by accident,
abuse, alteration, animal attack, storm damage, misuse or improper care.
THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS OF THIS LIMITED
WARRANTY. IN NO EVENT SHALL JOHNSON OUTDOORS GEAR LLC BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
What Johnson Outdoors Gear LLC Will Do: If after inspection we find that a
product failed due to a manufacturing or material defect, we will repair or replace
the product, at our option, without charge.
How to Obtain Warranty Service: Return the product, freight prepaid, to the Dealer
from whom it was purchased; or, contact our Customer Satisfaction Department for
return authorization: toll free 1-800-572-8822. Collect shipments or shipments
without return authorization cannot be accepted. The product registration card
packaged with our product need not be returned for the warranty to be effective
and for you to receive warranty service.
Repairs: If your Johnson Outdoors Gear LLC product needs service or repair due to
normal wear and tear, animal attack, accident or some other reason that is not
covered under the warranty we will provide the necessary service for a reasonable
charge, plus shipping and handling. We require that products accepted for any
repair be properly cleaned according to our recommended care instructions. Please
send your product or component that requires repair (e.g., tent fly), postage
prepaid, along with a description of what needs attention. For service and repairs,
please contact our Customer Satisfaction Department: toll free 1-800-572-8822
How State Law Relates To This Warranty: This warranty gives you specific legal
rights, and you may have other rights that vary from state to state.
ULTRAVIOLET LIGHT:
SAFETY INFORMATION: IMPORTANT SAFETY INSTRUCTIONS
Save these instructions. This manual contains important safety and
operating instructions applicable to the safe and efficient use of the E!
Power Pak DC power source and your Eureka! E! Power shelter with 12v
outlets.Failure to use the power pack in any way other than originally
intended by Johnson Outdoors Gear LLC will void the warranty and may
damage the unit or result in injury.Use of an attachment not recommended
or sold by Johnson Outdoors Gear LLC may result in risk of fire, electric
shock, injury to persons, or property damage.The E! Power Pak is not
intended for use by children at any time.
DO NOT insert any foreign objects into the 12v outlet on the E! Power Pak, or
the 12v outlets in the shelter.
DO NOT expose the E! Power Pak or 12v outlets in the shelter to water, rain,
snow or spray.
Ultraviolet light damage to tent fabric is caused by excessive exposure to sunlight.
While our fabrics are UV resistant, any synthetic fabric is susceptible to UV
degradation. UV damage will cause nylon and polyester to become brittle and
tear easily. We recommend that you use the rain fly even on clear days. It acts as
a sunscreen to the tent. A rain fly is both easier and less expensive to replace if
damaged. UV damage can be minimized by erecting tents on shaded sites with
low exposure to direct sunlight.
GENERAL POLE CARE:
• Never let tent poles snap together as this can damage the pole end.
• Do not drop tent or pole bags on their ends and do not bounce a tent bag on its
end to get the tent out. These actions may cut the shock cord and damage the
pole ends.
• The aluminum frame may bend slightly and take a “set” through usage; this
normally does not affect the performance of the frame.
Staking in special conditions:
• Sand. Use long, broad stakes with plenty of surface area.
• Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel
stakes separately. Their sharp edges can cut fabric and leave rust
stains, which might damage your tent.
• Snow. Use “dead man” anchors. Tie the tent to buried objects
(branches, tent bags, or stuff sacks filled with snow); or tie tents to
snow shoes, skis, or ski poles, which are stuck in the snow.
GUY LINES:
Do not depend on staking alone to keep your tent secure in high wind.
Done correctly, the addition of guy lines can save your tent in
exceptional weather.
• Make sure that each hook and loop fastener on the underside of the
fly is securely wrapped around the tent frame.
• Attach the guy rope, from the stake bag, to each guy out loop on fly.
• Stake all guy lines 6’ out from the edge of the tent. The optimal angle
from the ground to the guy line is 45˚. See fig a. In high wind,
additional guy lines should be used. On the N!ergy 9 and 1210 add a
secondary guy line off of each guy out point. See fig b.
• On the N!ergy 1310, guy ropes are pre-attached & stored in pockets at
each guy out location. In high wind, attach a secondary line at each
guy out point on the fly and half way down the tan mid-poles. See fig c.
The N!ergy Screenhouse has pre-attached reflective guy ropes at each
DO NOT connect any device with a neutral conductor (via an AC inverter)
to the E! Power Pak or the 12v outlets.
DO NOT use the E! Power Pak if it is damaged. Use care not to drop the unit. A
drop or fall can damage the unit even though no visible damage may be
apparent.
DO NOT expose the E! Power Pak to temperatures over 104˚F/40˚C. Always
store the E! Power Pak in a dry environment. Ideal storage temperature is
70˚F/21˚ C.
DO NOT permit the battery in the E! Power Pak to freeze. Never attempt to
recharge a frozen battery.
DO NOT disassemble the E! Power Pak. Incorrect reassembly may result in
a risk of electric shock or fire.If your E! Power Pak requires service, call
Schumacher Electric at 1-800-621-5485.
GENERAL TENT CARE:
• Sweep the tent floor daily to prevent damage from stones.
• Try not to wear shoes inside your tent.
• Use a ground cloth whenever possible.
• Do not keep food inside a tent. Hungry critters will chew through tent fabric in
search of food.
STORAGE:
• Make sure the tent is completely dry, then store loosely rolled, in a dry, cool
place. To prevent dust from collecting on the tent, cover it with a cloth. This
allows the nylon/polyester fabric to breathe.
• Ideally, the tent poles should be stored in their fully assembled state. This
reduces the tension on the shock cord, prolonging its life.
• The tent bag should be used only as a carry sack and not for storage.
COLOR TRANSFER:
• Do to the nature of tent fabrics, color can transfer from darker to lighter fabrics
when the two fabrics are in contact over time when wet, damp or exposed to the
combination of moisture and high heat. This does not effect the tent’s
performance. To prevent / minimize color transfer, always make sure your tent is
completely dry prior to packing and storage.
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame
source. The application of any foreign substance to the tent
fabric may render the flame-resistant properties ineffective.
DO NOT operate any device which burns fuel inside your tent.
Combustion consumes oxygen and can produce dangerous
levels of carbon monoxide, which could lead to serious injury or
death.
Johnson Outdoors Gear LLC
Your failure to follow these warnings could cause death, serious
injury or permanent disability to you or others.
REV. C FEB.09
corner.
Download from Www.Somanuals.com. All Manuals Search And Download.
|