Beko Hair Dryer DPU 7360 GX User Manual

Dryer  
DPU 7360 GX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 Important safety instructions  
This section contains safety instructions  
that will help protect from risk of personal  
injury or property damage. Failure to  
follow these instructions shall void any  
warranty.  
checked by a qualified electrician or  
the Authorized Service Agent. Our  
company shall not be liable for any  
damages that will arise when the  
product is used without grounding in  
accordance with the local regulations.  
The product should not be plugged  
in during installation, maintenance,  
cleaning and repair works.  
Always have the installation and  
repairing procedures carried out  
by the Authorized Service Agent.  
Manufacturer shall not be held  
liable for damages that may arise  
from procedures carried out by  
unauthorized persons.  
General safety  
Never place the product on a carpet-  
covered floor; otherwise, lack of  
airflow beneath the machine will  
cause electrical parts to overheat.  
This will cause problems with your  
product.  
Do not operate the product if the  
power cable / plug is damaged. Call  
the Authorized Service Agent.  
Do not make any changes on the  
plug supplied with the product. If it is  
not compatible with the socket, have  
a qualified electrician change the  
socket with a suitable one.  
Do not use electrical devices in the  
product.  
Do not connect the air exit of the  
product to the chimney holes which  
are used for the exhaust fumes of the  
devices operating with gas or other  
types of fuel.  
You must provide enough ventilation  
in order to prevent gases exiting from  
devices operating with other types of  
fuels including the naked flame from  
accumulating in the room due to the  
back fire effect.  
Items cleaned or washed with  
gasoil/fuel oil, dry-laundry solvents  
and other combustible or explosive  
materials as well as the items that are  
contaminated or spotted with such  
materials should not be dried in the  
product since they emit flammable or  
explosive vapor.  
Never touch the plug with wet hands!  
Never unplug by pulling on the cable,  
always pull out by grabbing the plug.  
Connect the product to a grounded  
outlet protected by a fuse of suitable  
capacity as stated in the technical  
specifications table.  
Power cable of this product is  
equipped with a conductor and  
a grounding plug that allows for  
grounding the product. This plug  
must be inserted into a socket  
which is installed and grounded in  
accordance with the local laws and  
regulations. Grounding installation  
decreases the risk of electric shock  
by opening a path with low resistance  
for the electricity flow in case of a  
malfunction or failure. Do not neglect  
to have the grounding installation  
made by a qualified electrician.  
If you have any suspect about  
the grounding installation, have it  
Do not dry the laundry cleaned with  
industrial chemicals in the dryer.  
Oil-affected items can ignite  
spontaneously, especially when  
exposed to heat sources such as in  
a tumble dryer. The items become  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 EN  
warm, causing an oxidation reaction  
in the oil. Oxidation creates heat. If  
the heat cannot escape, the items  
can become hot enough to catch fire.  
Piling, stacking or storing oil-affected  
items can prevent heat from escaping  
and so create a fire hazard.  
If it is unavoidable that fabrics that  
contain vegetable or cooking oil or  
have been contaminated by hair care  
products be placed in a tumble dryer  
they should first be washed in hot  
water with extra detergent - this will  
reduce, but not eliminate, the hazard.  
Underwear that contains metal  
reinforcements should not be dried in  
the dryer. Dryer can get damaged if  
metal reinforcements come loose and  
break off during drying.  
The final step of the drying  
programme, namely the cool-down  
step is performed without applying  
heat to ensure that the laundry items  
are kept at a temperature that will  
not damage them. If you open the  
loading door before the cool-down  
step completes, hot vapour will come  
out.  
ANever stop the dryer before the  
programme completes. If you must  
do this, remove all laundry quickly  
and lay them out to a suitable place  
to dissipate the heat.  
Always clean the lint filter before or  
after each loading. Never operate the  
dryer without the lint filter installed.  
Clean inside and exhaust duct of the  
product regularly. Do not allow fibre,  
dust and dirt accumulation around  
the exhaust exit and at adjacent  
areas.  
Power cable plug must be within easy  
reach after installation.  
Do not dry unwashed items in the  
dryer.  
Items soiled with cooking oils,  
acetone, alcohol, fuel oil, kerosene,  
stain removers, turpentine, paraffin  
and paraffin removers must be  
washed in hot water with plenty of  
detergent before being dried in the  
dryer.  
Garments or pillows bolstered with  
rubber foam (latex foam), shower  
bonnets, water resistant textiles,  
materials with rubber reinforcement  
and rubber foam pads should not be  
dried in the dryer.  
Do not use fabric softeners and  
anti-static products unless they are  
recommended by the manufacturers  
of the relevant product.  
Use softeners, anti-static products  
and etc. in accordance with the  
Never attempt to repair the product  
yourself. Do not perform any  
repair or replacement procedures  
on the product even if you know  
or have the ability to perform the  
required procedure unless it is  
clearly suggested in the operating  
instructions or the published service  
manual. Otherwise, you will be  
putting your life and others' lives in  
danger.  
For failures that you cannot remedy  
by applying the procedures in safety  
instructions, turn off and unplug  
the product and call the Authorized  
Service Agent.  
Do not reach into the machine when  
the drum is spinning.  
Do not use extension cords, multi-  
plugs or adaptors to connect the  
dryer to power supply in order to  
decrease the risk of fire and electric  
shock.  
Never wash the product by spreading  
or pouring water onto it! There is the  
risk of electric shock!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4 EN  
instructions of their manufacturers.  
Do not install the product behind a  
door with a lock, sliding door or a  
hinged door which can strike the  
product.  
Do not install or leave the dryer in  
places where it will be exposed to  
outdoor conditions.  
Your product can be operated at  
temperatures between +5°C and  
+35°C. If the operating conditions fall  
outside of this range, operation of the  
product will be adversely affected and  
it can get damaged.  
Do not tamper with the controls.  
Unplug the product when it is not in  
use.  
Product must only be used for  
drying of textiles that are marked  
accordingly.  
Dry only those articles in your product  
that are stated in this manual.  
Remove all objects from pockets  
such as lighters and matches.  
This product is not intended to be  
used by persons with physical,  
sensory or mental disorders or  
unlearned or inexperienced people  
(including children) unless they are  
attended by a person who will be  
responsible for their safety or who will  
instruct them accordingly for use of  
the product.  
Children's safety  
Remove the loading door of  
Electrical products are dangerous for  
the children. Keep children away from  
the product when it is operating. Do  
not let them tamper with the product.  
Do not allow children sit/climb on or  
enter in the product.  
Do not forget to close the loading  
door when leaving the room where  
the product is located.  
Packaging materials are dangerous  
to children. Keep the packaging  
materials out of reach of children or  
dispose them by classifying according  
to waste directives.  
the drying compartment before  
decommissioning or disposing of the  
product.  
Check all garments before loading  
and make sure that there is no any  
lighters, coins, metal pieces, needles,  
and etc. in their pockets or on them.  
Make sure that the pets do not enter  
into the product. Check the drum of  
the product before using it.  
Make sure that original spare parts  
and accessories are used during  
maintenance works.  
Do not lean on the loading door when  
it is open. The product may tip over.  
When your machine is not in use  
or when you unload the laundry  
after completion of drying process,  
turn the machine off with the On/  
Off button. In cases where the On/  
Off button is in On position (while  
the machine is energized), keep the  
loading door closed.  
Intended use  
This product has been designed for  
domestic use. It should not be used  
for other purposes.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5 EN  
2 Installation  
should stay at the same place where  
its connections have been made.  
When installing the product, make  
sure that the rear wall of it does  
not touch anywhere (tap, socket,  
etc.). Also pay attention to select an  
installation location which you will not  
be required to change afterwards.  
Place the product at least 1.5  
cm away from the edges of other  
furniture.  
Refer to the nearest Authorized Service  
Agent for installation of the product.  
To make the product ready for use,  
make sure that the electricity and water  
drainage system are appropriate before  
calling the Authorized Service Agent. If  
they are not, call a qualified technician  
and plumber to have any necessary  
arrangements carried out.  
CPreparation of the product's  
location as well as the electrical and  
BDo not place the product on the  
waste water installations is under  
customer's responsibility.  
power cable.  
BInstallation and electrical connections  
Removing the transportation  
safety assembly  
of the product must be carried out  
by the Authorized Service Agent.  
Manufacturer shall not be held  
liable for damages that may arise  
from procedures carried out by  
unauthorized persons.  
ARemove the transportation safety  
assembly before using the product for  
the first time.  
1. Open the loading door.  
2. There is a nylon bag inside the drum  
that contains a piece of styrofoam.  
Hold it from its section marked with  
XX XX.  
3. Pull the nylon towards yourself and  
remove the transportation safety  
assembly.  
APrior to installation, visually check if  
the product has any defects on it. If  
so, do not have it installed. Damaged  
products cause risks for your safety.  
ALet your dryer wait for 12 hours  
before starting to use it.  
Appropriate installation  
location  
Install the product on a stable and  
level surface.  
Dryer is heavy. Do not move it by  
yourself.  
Operate your product in a well  
ventilated, dust-free environment.  
Do not block the air ducts in front of  
and under the product with materials  
such as long pile rugs, wooden  
blocks and bands.  
AMake sure that no part of the  
transportation safety assembly  
remains inside the drum.  
Do not install the product behind a  
door with a lock, sliding door or a  
hinged door which can strike the  
product.  
Under counter installation  
This product can be installed under a  
counter if the height of the counter is  
sufficient.  
Once the product is installed, it  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6 EN  
Connecting to the drain  
In products equipped with condenser  
unit, water accumulates in the water tank  
during the drying cycle. You should drain  
accumulated water after each drying  
cycle.  
You can directly drain accumulated water  
through the water drain hose supplied  
with the product instead of periodically  
draining the water collected in the water  
tank.  
AWhile using undercounter dryer, it  
should never be operated without  
undercounter installation part.  
Dryer Depth  
60 cm  
54 cm  
Stock  
number of  
under-bench 2979600100 2973600100  
installation  
part  
Leave at least 3 cm of space around  
the sides and the rear wall of the  
product when installing it under a  
counter or in a cupboard.  
Mounting over a washing  
machine  
A fixing device should be used  
between the two machines  
when installing the dryer above a  
washing machine. The fixing device  
(2977200100 white/2977200400  
grey) must be installed by the  
Authorized Service Agent.  
Total weight of the washing machine  
and the dryer -with full load- when  
they are placed on top of each other  
reaches to approx. 180 kilograms.  
Place the products on a solid floor  
that has sufficient load carrying  
capacity!  
Connecting the water drain hose  
1. Pull hose in the product by hand in  
order to disconnect it from where it is  
connected. Do not use any tools to  
remove the hose.  
2. Connect one end of the drain hose  
supplied separately with the product  
to the connection point from where  
you removed the hose of the product  
in previous step.  
3. Connect the other end of the drain  
hose directly to the wastewater drain  
or to the washbasin.  
AHose must be fixed in every type  
of connection. Your house will be  
flooded if the hose comes loose  
during water discharge.  
CWater drain hose should be attached  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7 EN  
to a height of maximum 80 cm.  
have a contact distance of minimum  
3 mm.  
CMake sure that the water drain hose  
is not stepped on and it is not folded  
BDamaged power cable must be  
between the drain and the machine.  
replaced by the Authorized Service  
Agent.  
Adjusting the feet  
BIf the product is faulty, it must not be  
In order to ensure that the product  
operates more silently and vibration-free,  
it must stand level and balanced on its  
feet. Balance the machine by adjusting  
the feet.  
operated unless it is repaired! There is  
the risk of electric shock!  
First use  
Before starting to use the product, make  
sure that all preparations are made in  
accordance with the instructions in  
sections "Important safety instructions"  
and "Installation".  
Turn the feet to left or right until the  
machine stands level and firmly.  
Disposing of packaging  
material  
Packaging materials are dangerous to  
children. Keep packaging materials in  
a safe place away from reach of the  
children.  
Packaging materials of the product are  
manufactured from recyclable materials.  
Dispose of them properly and sort  
in accordance with recycled waste  
instructions. Do not dispose of them with  
normal domestic waste.  
Transportation of the product  
1. Unplug the product before  
transporting it.  
2. Remove the water drain (if any) and  
chimney connections.  
CNever remove the adjustable feet  
from their housings.  
Electrical connection  
Connect the product to a grounded outlet  
protected by a fuse complying with the  
values in the "Technical specifications"  
table. Our company shall not be liable  
for any damages that will arise when the  
product is used without grounding in  
accordance with the local regulations.  
Connection must comply with  
national regulations.  
Power cable plug must be within easy  
reach after installation.  
The voltage and allowed fuse or  
breaker protection are specified in  
the “Technical specifications” section.  
If the current value of the fuse or  
breaker in the house is less than 10  
Amps, have a qualified electrician  
install a 10 Amp fuse.  
3. Drain the water in the product  
completely.  
AWe recommend carrying the product  
in upright position. If it is not possible  
to carry the machine in the upright  
position, we recommend carrying  
it by tilting towards the right side  
when looked from the front. After the  
product is moved to its new place,  
you should wait for 12 hours before  
starting it.  
The specified voltage must be equal  
to your mains voltage.  
Do not make connections via  
extension cables or multi-plugs.  
The main fuse and switches must  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8 EN  
Disposing of the old product  
Dispose of the old product in an  
environmentally friendly manner.  
Refer to your local dealer or solid waste  
collection centre in your area to learn how  
to dispose of your product.  
CWater collected during operation is  
pumped to water tank. It is normal  
to hear pumping noise during this  
process.  
For children's safety, cut the power  
cable and break the locking mechanism  
of the loading door so that it will be  
nonfunctional before disposing of the  
product.  
Warnings about sounds  
CIt is normal to hear metallic noise from  
the compressor sometimes during  
operation.  
Technical specifications  
EN  
2
Height (adjustable)  
Width  
84,6 cm  
59,5 cm  
59,8 cm  
7 kg  
Depth  
Capacity (max.)  
Weight (net)  
51,5 kg  
Voltage  
Rated power input  
Model code  
See type label  
Type label is located behind the loading door.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9 EN  
3 Preparations for drying  
Things to be done for energy  
machine is not in use.  
Laundry suitable for drying in  
the machine  
saving  
Following information will help you use  
the product in an ecological and energy- CAlways obey the instructions given  
on the garment tags. Dry only the  
laundry having a label stating that  
they are suitable for drying in a dryer  
and make sure that you select the  
appropriate programme.  
efficient manner.  
Operate the product at a capacity  
suitable for the program you have  
selected and pay attention not to  
overload.  
Spin your laundry at the highest  
speed possible when washing them.  
Thus, the drying time is shortened  
and energy consumption is reduced.  
Dry the same type of laundry  
together.  
Follow the instructions in the user  
manual for programme selection.  
Leave sufficient clearance at the  
front and rear side of the dryer for  
air circulation. Do not block the  
ventilation grills at the front side of the  
product.  
A B C D  
l n m  
o p q  
Do not open the loading door of  
the machine during drying unless  
necessary. If you must certainly open  
the loading door, do not to keep it  
open for a long time.  
Laundry unsuitable for drying  
in the machine  
Laundry and items stated below are  
not suitable for drying in a dryer:  
Laundry items with metal  
attachments such as metal buttons,  
metal reinforcements or belt buckles.  
Woolen or silk garments, nylon  
stockings, delicate embroidered  
fabrics and sleeping bags.  
Garments made of delicate and  
valuable fabrics.  
Do not add new (wet) laundry during  
drying.  
Lint and fibres released from the  
laundry to the air during the drying  
cycle are collected in the Lint Filter.  
Clean the lint filter before or after each  
drying cycle.  
Clean the filter drawer regularly either  
when the Filter Drawer Cleaning  
warning symbol appears or after  
every 5 drying cycles  
Ventilate the room, where the dryer is  
located, well during drying.  
For models with lamp, keep the door  
closed if the On/Off button is pressed  
(if the machine is energized) when  
Tulle curtains.  
Items made of hermetic fibres such  
as pillows and quilts.  
Very wet laundry items.  
Unwashed dirty laundry items.  
Laundry items containing rubber  
foam or rubber.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10 EN  
load more than the capacity values stated  
in the table.  
Items cleaned, washed or spotted  
with gasoil/fuel oil, dry-laundry  
solvents, industrial chemicals or other  
combustible or explosive materials  
should not be dried in the dryer.  
Items soiled with cooking oils,  
acetone, alcohol, fuel oil, kerosene,  
stain removers, turpentine, paraffin  
and paraffin removers must be  
washed in hot water with plenty of  
detergent before being dried in the  
dryer.  
CIt is not recommended to load the  
dryer with laundry exceeding the  
level indicated in the figure. Drying  
performance will degrade when the  
machine is overloaded. Furthermore,  
dryer and the laundry can get  
damaged.  
Following weights are given as examples.  
Approximate  
weights (g)  
Home articles  
Preparing laundry for drying  
Cotton quit covers  
(double)  
Cotton quit covers  
(single)  
Bed sheets (double)  
Bed sheets (single)  
Large tablecloths  
Small tablecloths  
Tea napkins  
1500  
Check all garments before loading  
and make sure that there is no any  
lighters, coins, metal pieces, needles,  
and etc. in their pockets or on them.  
Laundry may be tangled after  
washing. Separate the laundry items  
before placing them into the dryer.  
Sort the laundry according to their  
types and thicknesses. Dry the same  
type of laundry together. For instance,  
thin kitchen towel and table cloths get  
dry earlier than the thick bath towels.  
1000  
500  
350  
700  
250  
100  
Bath towels  
Hand towels  
700  
350  
Approximate  
weights (g)  
150  
Garments  
CLaundry must be spun at the highest  
Blouses  
spin speed that the washing machine  
allows on basis of the fabric type.  
Correct load capacity  
Cotton shirts  
Shirts  
Cotton dresses  
Dresses  
300  
200  
500  
350  
Jeans  
700  
Handkerchiefs (10  
pieces)  
T-Shirts  
100  
125  
Follow the instructions in the “Programme  
selection and consumption table”. Do not  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11 EN  
Loading the laundry  
1. Open the loading door.  
2. Place the laundry in the machine  
without compressing.  
3. Push the loading door to close.  
AEnsure that no items are caught in  
the door.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12 EN  
4 Selecting a Programme and Operating Your Machine  
Control panel  
1
2
3
4
5
Shirts  
Jeans  
Daily  
Xpress  
Iron Dry  
Synthetics  
Wool  
Refresh  
Cupboard  
Dry  
Spin / Time  
Time Delay  
Mix  
Iron Dry  
Cupboard  
Dry  
Start/Pause  
Sport  
Cottons  
Babycare  
Delicates  
Extra Dry  
On / Off  
Freshen Up  
Cancel Press  
& Hold 3 sec.  
Timer  
Programmes  
Buzzer  
Cancel  
Dryness  
Level  
Anti-  
Creasing  
9
8
7
6
1. Washing Machine Spin Speed / Timer  
Programme Selection button  
2. Display  
3. Start / Pause / Cancel button  
4. Programme Selection knob  
5. On / Off button  
6. Anti-creasing button  
7. Dryness Level button  
8. Cancel Audio Warning button  
9. Time Delay buttons  
Spin speed / Timer programs*  
Operation symbol  
Pause symbol  
Water Tank warning symbol  
Filter cleaning warning symbol  
Filter Drawer Cleaning warning symbol  
Remaining Time indicator**  
Child-proof Lock warning symbol  
Time Delay mode  
Loading door open warning symbol  
Anti-creasing mode  
Audio Warning Level / Cancel Audio Warning  
Dryness Level  
Anti-creasing is activated  
*
Spin speed is used to show the remaining time more accurately. It does not  
affect the performance of your machine.  
** Time that appears on display indicates the remaining time until the end of the  
programme and changes according to the dampness level of the laundry.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13 EN  
Cupboard  
Dry  
Ventilation  
Anti  
Iron Dry  
Cottons Synthetics  
Extra dry  
Express  
Shirt  
Timer  
Creasing  
programs  
Child-proof  
lock  
Buzzer/ On/Off  
cancel  
Start  
pause  
cancel  
Tank  
full  
Filter  
Daily  
Jeans  
cleaning  
Timer  
Delay  
Wool  
Refresh  
Dryness  
Level  
Babycare Sport  
Spin  
Mixed  
Drying  
Rack  
Delicates  
Preparing the machine  
CFor further programme details,  
1. Plug in the machine.  
see "Programme selection and  
2. Place the laundry in the machine.  
3. Press the On / Off button.  
consumption table".  
Main programmes  
Depending on the fabric type, the  
following main programmes are available:  
• Cottons  
Dry durable laundry with this programme.  
Dries at normal temperature. It is  
recommended to use for your cotton  
items (bed sheets, quilt covers, towels,  
bathrobes, etc.).  
CPressing the On / Off button does  
not necessarily mean that the  
programme has started. Press Start  
/ Pause / Cancel button to start the  
programme.  
Programme selection  
1. Decide the appropriate programme  
from the table below which includes  
drying levels.  
2. Select the desired programme with  
the Programme Selection knob.  
Only the cotton laundry  
• Synthetics  
Dry less durable laundry with this  
programme. Recommended for  
synthetics.  
Additional programmes  
For special cases, following additional  
programmes are available in the machine.  
is dried at normal  
temperature. Thick and  
multi layered laundry  
Extra Dry  
(towels, linens, jeans and  
etc.) are dried in a way that  
they do not require ironing  
before being placed in the  
wardrobe.  
CAdditional programs may differ  
according to the features of your  
machine.  
• Express  
You can use this program to dry your  
cotton laundry that you have spun at  
high speeds in your washing machine.  
This program dries 1 kg cotton laundry (3  
Shirts/3T-shirts) in 45 minutes.  
Normal laundry  
(tablecloths, underwear  
Cupboard and etc.) are dried in a way  
dry  
that they do not require  
ironing before being placed  
in the wardrobe.  
CTo obtain better results from your  
dryer, your laundry must be washed  
Normal laundry (shirts,  
dresses and etc.) are dried  
ready to be ironed.  
at suitable programs and spun at the  
recommended speed in the washing  
Iron Dry  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14 EN  
machine.  
• Shirt  
This programme dries the shirts more  
sensitively and creases them less and  
thus, helps to iron them more easily.  
Take your laundry immediately out  
of the dryer and hang them after the  
program is over in order to prevent  
them from getting creased.  
• Freshen up  
Only ventilation is performed for 10  
minutes without blowing hot air. You can  
air the clothes that have been kept at  
closed environments for a long time and  
deodourise unpleasant odours thanks to  
this programme.  
CThere may be a little moisture on the  
shirts at the end of the programme.  
We recommend you not to leave the  
shirts in the dryer.  
• Jeans  
Use this programme to dry your jeans  
that are spun at high speeds in the  
washing machine.  
• Timer programmes  
You can select one of the 10 min., 20  
min., 30 min., 40 min., 50 min., 60 min.,  
80 min., 100 min., 120 min., 140 min.  
and 160 min. timer programmes to  
achieve the desired final drying level at  
low temperatures.  
• Mixed  
Use this programme to dry non-  
pigmenting synthetic and cotton laundry  
items together.  
• Sport  
Use this programme to dry together the  
synthetic and cotton laundry items and  
the laundry items made of mixed fabrics.  
• Wool Refresh  
CWith this programme, the machine  
dries for the time selected regardless  
of the dryness level.  
You can use this program to ventilate  
and soften your woolen laundry that can  
be washed in the washing machine. Do  
not use this program to dry your laundry  
completely. Take out your laundry and  
ventilate them immediately after the  
program is over.  
• Daily  
This program is used to dry cottons and  
synthetics daily, and lasts for 1.5 hour.  
• Babycare  
This program is used for baby clothes  
that bear machine dryable approval on its  
label.  
• Delicates  
You can dry your highly delicate laundry  
that are suitable for drying or laundry  
which is advised to be hand-washed at a  
lower temperature.  
CIt is recommended to use a cloth bag  
to prevent certain delicate laundry  
from getting creased or damaged.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15 EN  
Programme selection and consumption table  
EN  
Approximate  
amount of  
remaining  
humidity  
Spin speed in  
Drying time  
(minutes)  
Programs  
Capacity (kg)  
washing machine  
(rpm)  
Cottons / Coloreds  
Extra dry  
7
7
7
1000  
1000  
1000  
% 60  
% 60  
% 60  
175  
156  
125  
A
Cupboard dry  
A
Iron dry  
A
Babycare  
3
1.5  
4
1000  
1200  
1200  
1200  
1000  
1000  
1200  
600  
% 60  
%50  
%50  
%50  
%60  
%60  
%50  
%40  
%50  
80  
50  
Shirt  
Jeans  
120  
90  
Daily  
4
Mixed  
4
115  
105  
45  
Sport  
4
Express  
Delicates  
Wool Refresh  
Synthetics  
1
2
55  
1.5  
600  
8
Cupboard dry  
3.5  
3.5  
800  
800  
% 40  
% 40  
62  
50  
B
Iron dry  
B
Energy consumption values  
Energy consumption value kWh per  
year  
Programs  
Capacity (kg)  
Energy rating star  
6
Cottons-Extra Dry*  
7
163  
* : Energy Label standard program (AS/NZS 2442)  
All values given in the table have been fixed according to standard laboratory  
conditions. These values may deviate from the table according to the laundry type,  
laundry spin speed, environmental conditions and voltage fluctuations.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16 EN  
Auxiliary functions  
Audio Warning  
The machine will give an audio warning  
when the programme comes to an end.  
If you do not want the machine give an  
audio warning, press the Volume Level  
button repeatedly until "x" appears on the  
display. Use the same button to adjust  
the volume level.  
CPress Anti-creasing button to activate  
this function.  
Changing the contrast  
CYou can activate this function either  
Adjust the display contrast in order to  
make the symbols on the display appear  
clearer. It may particularly be necessary to  
change the contrast setting of the display  
when the dryer is installed over a washing  
machine.  
before or after the programme starts.  
Cancel  
audio warning  
Audio warning Audio warning  
level 1 level 2  
Audio warning  
level 3  
Dryness level  
Press and hold the Spin Speed / Timer  
Programme button for 3 seconds.  
When the contrast is changed, all  
symbols on the display will appear for  
3 seconds in order to indicate that the  
process is complete.  
Used to adjust the required dryness level.  
More drying is performed compared  
to the default settings when "+" sign  
appears and less drying is performed  
when "-" sign appears. Programme  
duration can change depending on the  
selection.  
CPerform the same procedure to revert  
back to the previous contrast setting.  
CYou can activate this function only  
Warning symbols  
before the programme has started.  
CWarning symbols may differ  
according to the model of your  
machine.  
Lint filter cleaning  
Anti-creasing  
When the programme is completed, a  
warning symbol will appear to remind that  
the filter needs to be cleaned.  
You can use Anti-creasing function to  
prevent laundry from creasing if you will  
not take the laundry out after the program  
has come to an end. This program  
rotates the laundry in every 240 second  
for 2 hours to prevent creasing.  
If the Filter Cleaning symbol flashes  
C
continuously, refer to “Troubleshooting”  
section.  
Anti-creasing is activated but the  
programme is still running in the first  
display image below. Drying cycle is  
completed and the Anti-creasing step has  
started in the second display image.  
Water tank  
When the programme is completed, a  
warning symbol will appear to remind that  
the water tank needs to be drained.  
If the water tank becomes full while  
the programme is running, the warning  
symbol will start to flash and machine will  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17 EN  
pause. Drain the water in the water tank  
and press Start / Pause / Cancel button  
to resume the programme. The warning  
symbol turns off and the programme  
resumes operating.  
countdown process, Time Delay  
symbol disappears, drying process  
starts and the programme duration  
is displayed. The time on the display  
is the total of normal drying time and  
delay time.  
Cleaning of filter drawer  
Warning symbol flashes with certain  
intervals to remind that the filter drawer  
needs to be cleaned.  
Time Delay is activated by pressing the  
Start / Pause / Cancel button in the  
above display image.  
Changing the delay time  
If you want to change the time during  
countdown:  
Loading door open  
This warning symbol appears when the  
loading door of the dryer is open.  
1. Press Start / Pause / Cancel  
button for 3 seconds to cancel the  
programme. Repeat the Time Delay  
procedure for the desired time.  
2. Set the desired delay time with Time  
Delay + and - buttons. The Time  
Delay symbol will flash.  
3. Press Start / Pause / Cancel button.  
The Time Delay starts to count down.  
The Time Delay symbol lights up.  
Pause symbol disappears. Start  
symbol appears.  
4. The “:” in the middle of the displayed  
delay time will start flashing.  
Cancelling the Time Delay  
If you want to cancel the Time Delay  
countdown and start the programme  
immediately:  
1. Press Start / Pause / Cancel  
button for 3 seconds to cancel the  
programme.  
Time Delay  
Time Delay function allows you to delay  
the startup of the programme up to 24  
hours.  
1. Open the loading door and put the  
laundry in.  
2. Select the drying programme, spin  
speed and, if required, the auxiliary  
functions.  
3. Press Time Delay buttons + and - to  
set the desired time delay. The Time  
Delay symbol will flash.  
4. Press Start / Pause / Cancel button.  
The Time Delay starts to count down.  
The Time Delay symbol lights up.  
Start symbol appears. The “:” in the  
middle of the displayed delay time will  
start flashing.  
2. Press Start / Pause / Cancel button  
to start the programme you have  
previously selected.  
CAdditional laundry may be loaded  
/ taken out during the Time Delay  
period. At the end of the Time Delay  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18 EN  
Starting the programme  
Press Start / Pause / Cancel button to  
start the programme.  
Start / Pause symbol will light up to  
indicate that the programme has started  
and ":" symbol between the remaining  
time will continue flashing.  
Child-proof Lock  
Machine is equipped with a Childproof  
Lock which prevents interfering with the  
current programme flow by pressing  
any button. All buttons except the On  
/ Off button on the control panel are  
deactivated when the Child-proof Lock is  
active.  
In order to activate the Childproof Lock,  
press Audio Warning and Anti-Creasing  
buttons simultaneously for 3 seconds.  
To start a new programme after the  
current programme is over or to interrupt  
the current programme, the Child-proof  
Lock should be deactivated. Press the  
same buttons for 3 seconds again to  
deactivate the Child-proof Lock.  
Progress of programme  
Anti-  
creasing  
Drying  
Wardrobe  
(Extra)  
Iron  
Ventilation  
Progress of a running programme is  
indicated on the display by means of a  
set of symbols.  
At the beginning of each programme  
step, the relevant symbol in the series of  
symbols will light up and thus, at the end  
of the programme, all symbols will remain  
lit up. The rightmost symbol on the  
display indicates the step being carried  
out.  
CLock symbol will appear on the  
display when the Child-proof Lock is  
activated.  
CChild-proof Lock is deactivated when  
the machine is switched off and on  
Drying  
with On / Off button.  
Drying symbol lights up in all programmes  
apart from ventilation.  
Iron Dry  
Starts to illuminate when the dryness level  
reach Iron Dry step.  
Cupboard dry  
Starts to illuminate when the dryness level  
reach Wardrobe Dry step.  
Extra dry  
Starts to illuminate when the dryness level  
reach Wardrobe Dry Extra step.  
Ventilation  
When the Child-proof Lock is activated:  
Display symbols will not change  
even if the position of Programme  
Selection knob is changed while the  
machine is running or in halt.  
If the Child-proof Lock is deactivated  
after changing the position of  
the Programme Selection knob  
while the machine is running, the  
machine stops and new programme  
information is displayed.  
Changing the programme after  
Ventilation symbol illuminates when the  
programme comes to an end.  
it has started  
After the machine starts, you can change  
the selected programme and dry your  
laundry in a different programme.  
CAnti-creasing symbol will illuminate  
at the end of the programme if Anti-  
creasing function is activated.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19 EN  
1. If you want to select Extra Dry  
programme instead of Iron Dry  
programme, press and hold the  
Start / Pause / Cancel button for 3  
seconds to cancel the programme.  
2. Select Extra Dry programme by  
turning the Programme Selection  
knob.  
However, this process will increase  
the programme time and energy  
consumption since the drying  
process will be interrupted repeatedly.  
Therefore, it is recommended to add  
laundry before the drying programme  
has started.  
CIf you select a new programme by  
3. Press Start / Pause / Cancel button  
to start the programme.  
turning the Programme Selection  
knob while your machine is in Pause  
mode, then the current program  
is aborted and new programme  
information is displayed.  
Do not touch the inner surface of  
the drum when adding or taking  
out laundry while a programme is  
running. Surfaces of the drum are  
hot.  
CYou can also select a new  
programme by turning the  
Programme Selection knob while the  
machine is operating. In this case,  
current programme is aborted and  
the new programme information  
appears on the display.  
Canceling the programme  
If you want to stop drying and cancel  
the programme for any reason after the  
machine has started to run, press and  
hold the Start / Pause / Cancel button  
for 3 seconds. Lint Filter Cleaning and  
Water Tank warning symbols light up and  
"End" label appears on the display as a  
reminder at the end of this period.  
Adding / removing laundry in Pause  
mode  
In order to add or take out laundry after  
the drying programme has started:  
1. Press Start / Pause / Cancel button  
to switch the machine to Pause  
mode. Drying process will stop.  
2. While in Pause mode, open the  
loading door, add or take out laundry  
and close the loading door.  
3. Press Start / Pause / Cancel button  
to start the programme.  
AAs the inside of the machine will be  
excessively hot when you cancel  
CAny laundry added after the drying  
the programme while the machine  
is running, activate the ventilation  
program to cool it down.  
process has started may cause the  
clothes that are already dried in the  
machine intermingle with wet clothes  
and the result will be wet laundry after  
the drying process is over.  
CMachine will stop if you turn the  
Programme Selection knob while  
it is operating. In this case, current  
programme is aborted and the new  
programme information appears on  
CYou may repeat laundry adding  
or removing process as many  
times as you desire during drying.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20 EN  
the display.  
End of programme  
Lint Filter Cleaning and Water Tank  
warning symbols light up in the  
programme follow-up indicator and  
"End” label appears on the display when  
the programme comes to an end. The  
loading door can be opened and the  
machine becomes ready for a second  
cycle.  
Press On / Off button to switch off the  
machine.  
CIf Anti-creasing function is activated  
and the laundry is not taken from  
the machine at the end of the  
programme, 2-hours Anti-creasing  
programme is activated.  
CClean the lint filter after each drying.  
(See “Lint Filter / Loading Door Inner  
Surface”)  
CDrain the water tank after each drying  
cycle. (See "Draining the water tank")  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21 EN  
5 Maintenance and cleaning  
Service life of the product extends and  
frequently faced problems decrease if  
cleaned at regular intervals.  
up on the lint filter surface. Dry the lint  
filter completely before reinstalling it.  
BThis product must be unplugged  
during maintenance and cleaning  
works (control panel, body, etc.).  
Lint Filter / Loading Door Inner  
Surface  
Lint and fibres released from the laundry  
to the air during the drying cycle are  
collected in the Lint Filter.  
CClean the entire inner surface of  
the loading door and loading door  
gasket.  
C*Such fibre and lint are generally  
formed during wearing and washing.  
AAlways clean the lint filter and the  
inner surfaces of the loading door  
after each drying process.  
CYou can clean the lint filter housing  
with a vacuum cleaner.  
To clean the lint filter:  
1. Open the loading door.  
Cleaning the sensors  
2. Remove the lint filter by pulling it up  
and open the lint filter.  
3. Clean lint, fibre, and cotton raveling  
by hand or with a soft piece of cloth.  
4. Close the lint filter and place it back  
into its housing.  
CA layer can build up on the lint filter  
pores that can cause clogging of the  
lint filter after using the machine for a  
while. Wash the lint filter with warm  
water to remove the layer that builds  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22 EN  
There are dampness sensors in the  
machine that detect whether the laundry  
is dry or not.  
2. Drain the water in the tank.  
To clean the sensors:  
1. Open the loading door of the  
machine.  
2. Allow the machine to cool down if it is  
still hot due to the drying process.  
3. Wipe the metal surfaces of the sensor  
with a soft cloth, dampened with  
vinegar and dry them.  
3. If there is lint accumulation in the  
funnel of the water tank, clean it  
under running water.  
CClean metal surfaces of the sensors 4  
times a year.  
CDo not use metal tools when cleaning  
4. Place the water tank into its seat.  
Cleaning the filter drawer  
Lint and fibre that could not be captured  
by the lint filter are blocked in the filter  
drawer behind the kick plate. Filter  
Drawer Cleaning warning light will light up  
maximum at every 5 drying cycles as a  
metal surfaces of the sensors.  
ANever use solvents, cleaning agents  
or similar substances for cleaning due  
to the risk of fire and explosion!  
Draining the water tank  
Dampness of the laundry is removed and  
condensed during drying process and the reminder.  
water that arise accumulates in the water  
tank. Drain the water tank after each  
drying cycle.  
There is a two-level filter in the filter  
drawer. The first level is the filter drawer  
sponge and the second level is the filter  
cloth.  
To clean the filter drawer:  
1. Press the kick plate button to open  
the kick plate.  
ACondensed water is not potable!  
ANever remove the water tank when  
the programme is running!  
If you forget to drain the water tank, the  
machine will stop during the subsequent  
drying cycles when the water tank is full  
and the Water Tank warning symbol will  
flash. If this is the case, drain the water  
tank and press Start / Pause / Cancel  
button to resume the drying cycle.  
To drain the water tank:  
1. Pull the drawer and remove the water  
tank carefully.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23 EN  
2. Remove the filter drawer cover by  
6. Clean lint, fibre, and cotton raveling  
on the filter cloth by hand or with a  
soft piece of cloth.  
turning it in the direction of arrow.  
3. Pull out the filter drawer.  
CWhen you notice a layer that may  
lead clogging on filter cloth, please  
clean the layer by washing in  
warm water. Let the filter cloth dry  
thoroughly before installing back the  
filter drawer.  
7. Hand-wash the filter drawers sponge  
to remove hair and lint on it. Squeeze  
the sponge by hand to remove  
excessive water.  
4. Open the filter drawer by pressing the  
CIt is not necessary to clean the  
red button.  
sponge if lint and fibre accumulation  
on it is not significant.  
8. Place the sponge back into its place.  
5. Take out the filter drawer sponge.  
9. Close the filter drawer as to lock the  
red button.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24 EN  
10. Place the filter drawer back into its  
place, turn the filter drawer cower  
clockwise making sure that it is  
closed securely.  
Cleaning the evaporator  
Clean the lints accumulated on the fins  
of the evaporator located behind the filter  
drawer with a vacuum cleaner.  
11. Close the kick plate cover.  
CYou can also clean by hand provided  
that you wear protective gloves. Do  
not attempt to clean with bare hands.  
CDrying without the filter drawer  
sponge in place will damage the  
machine!  
CA dirty lint filter and filter drawer will  
cause longer drying periods and  
higher energy consumption.  
CA layer can build up on the lint filter  
pores that can cause clogging of the  
lint filter after using your machine for  
a while. Wash the lint filter with warm  
water to remove the layer that builds  
up on the lint filter surface. Dry the lint  
filter completely before using it.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25 EN  
6 Troubleshooting  
Drying process takes too much time.  
Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.  
Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter drawer.  
Ventilation grids on the front side of the machine are blocked. >>> Remove the  
objects (if any) that block ventilation in front of the ventilation grids.  
Ventilation is not sufficient since the room where the machine is installed is  
very small. >>> Open the door and window of the room to avoid the room  
temperature increase too much.  
Lime deposit has built up on the dampness sensor. >>> Clean the dampness  
sensor.  
Excessive laundry is loaded. >>> Do not load the dryer in excess.  
Laundry is not spun sufficiently. >>> Spin your laundry at a higher speed in your  
washing machine.  
Laundry comes out wet at the end of drying.  
CAfter drying, the hot clothes feel damper than their actual dampness level.  
It is likely that the selected programme did not suit the laundry type.>>>Checking  
the care labels on clothes, select appropriate programme for the laundry type or  
use timer programmes in addition.  
Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.  
Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter  
drawer.  
Excessive laundry is loaded. >>> Do not load the dryer in excess.  
Laundry is not spun sufficiently. >>> Spin your laundry at a higher speed in your  
washing machine.  
Dryer does not switch on or the programme does not start. Dryer does not start  
when it is set.  
It is not plugged in. >>> Make sure that the machine is plugged in.  
The loading door is ajar. >>> Make sure that the loading door is closed securely.  
Programme is not selected or the Start / Pause / Cancel button is not pressed.  
>>> Make sure that the programme is selected and the machine is not in Pause  
mode.  
Childproof Lock is activated. >>> Deactivate the Childproof Lock.  
Programme is interrupted without any cause.  
Loading door is ajar. >>> Make sure that the loading door is closed securely.  
There was a power failure. >>> Press Start / Pause / Cancel button to start the  
programme.  
Water tank is full. >>> Drain the water tank.  
Laundry has shrunk, become felted or deteriorated.  
A programme suitable for the laundry type is not used. >>> Check the garment  
tag and select a programme suitable for the fabric type.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26 EN  
Drum lighting does not turn on. (On models with lamp)  
Dryer is not switched on with the On / Off button. >>> Make sure that the dryer is  
switched on.  
Lamp is defective. >>> Call Authorized Service Agent to have the lamp replaced.  
End/Anti-creasing symbol is on.  
Anti-creasing programme is activated in order to prevent laundry that has  
remained in the machine from creasing. >>> Turn off the dryer and take out the  
laundry.  
End symbol is on.  
Programme is over. Turn off the dryer and take out the laundry.  
Lint Filter Cleaning symbol is on.  
Lint filter is not cleaned. >>> Clean the lint filter.  
Lint Filter Cleaning symbol is flashing.  
Filter housing is clogged with lints. >>> Clean the lint filter housing.  
A deposit has built up on the lint filter pores that may cause clogging. >>> Wash  
the lint filter with warm water.  
Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter  
drawer.  
Water leaks from the loading door  
Lint has accumulated on the inner surfaces of the loading door and on the  
surfaces of the loading door gasket. >>> Clean the inner surfaces of the loading  
door and the surfaces of the loading door gasket.  
Loading door opens spontaneously.  
Loading door is ajar. >>> Push the loading door to close until you hear a locking  
sound.  
Water Tank warning symbol is on/flashing.  
Water tank is full. >>> Drain the water tank.  
Water draining hose is bent. >>> If the product is connected directly to a  
wastewater drain, check the water drain hose.  
Filter Drawer Cleaning warning symbol is flashing.  
Filter drawer is not cleaned. >>> Clean the sponge and the filter cloth in the filter  
drawer.  
AIf you cannot eliminate the problem although you follow the instructions in this  
section, consult your dealer or the Authorized Service Agent. Never try to repair a  
nonfunctional product yourself.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Abocom Network Card USB Home PhoneLine 1Mbps Network Adapter User Manual
Accton Technology Switch ES4626 User Manual
ADC Power Supply ACE COM L1 User Manual
Agilent Technologies Computer Drive FS4100 User Manual
Allied Telesis Network Card AT 2911LTX LC User Manual
AMX TV Receiver CB TP7 User Manual
Atlona Microscope Magnifier AT DVIRX RSNET User Manual
Audiovox Automobile Alarm APS 15CH User Manual
Baby Einstein Baby Toy L8906 User Manual
Panel Television Elba 63 TD 61 100 MTUser Manual