Beko Clothes Dryer DV 7220 X User Manual

Dryer  
DV 7220 X  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 Important safety information  
This section includes safety information that will  
help protection from risks of personal injuries  
or materialistic damages. Failure to follow  
these instructions shall cause any warranty and  
well as the items that are contaminated  
or spotted with such materials should not  
be dried in the product since they emit  
flammable or explosive vapor.  
reliability commitment to become void.  
Do not dry items cleaned with industrial  
chemicals in the dryer.  
General safety  
Do not dry unwashed items in the dryer.  
Items soiled with cooking oils, acetone,  
alcohol, fuel oil, kerosene, stain remover,  
turpentine, paraffin and paraffin removers  
must be washed in hot water with plenty of  
detergent before being dried in the dryer.  
Garments or pillows bolstered with rubber  
foam (latex foam), shower bonnets, water  
resistant textiles, materials with rubber  
reinforcement and rubber foam pads  
should not be dried in the dryer.  
Do not use fabric softeners and anti-static  
products unless they are recommended by  
the manufacturers of the fabric softener or  
the product.  
Oil-affected items can ignite spontaneously,  
especially when exposed to heat sources  
such as in a tumble dryer. The items  
become warm, causing an oxidation  
reaction in the oil. Oxidation creates heat.  
If the heat cannot escape, the items can  
become hot enough to catch fire. Piling,  
stacking or storing oil-affected items can  
prevent heat from escaping and so create  
a fire hazard.  
Never place the machine on a carpet-  
covered floor, otherwise, lack of airflow  
beneath the machine may cause electrical  
parts to overheat. This will cause problems  
with your machine.  
If the power cable or mains plug is  
damaged, you must call qualified  
electrician for repair.  
The product should not be plugged in  
during installation, maintenance and repair  
works. Such works should always be made  
by the technical service. Manufacturer  
shall not be held responsible for damages  
arising from processes carried out by any  
unauthorised persons.  
Connect the product to a grounded outlet  
protected by a fuse of suitable capacity as  
stated in the technical specifications table.  
Operate your product at temperatures  
between +5°C and +35°C.  
Do not use electrical devices in the  
product.  
Do not connect the air exit of the product  
to the chimney holes which are used for  
the exhaust fumes of the devices operating  
with gas or other types of fuel.  
If it is unavoidable that fabrics that contain  
vegetable or cooking oil or have been  
contaminated by hair care products be  
placed in a tumble dryer they should  
first be washed in hot water with extra  
detergent - this will reduce, but not  
eliminate, the hazard.  
You must provide enough ventilation in  
order to prevent gases exiting from devices  
operating with other types of fuels including  
the naked flame from accumulating in the  
room due to the back fire effect.  
Always clean the lint filter before or after  
each loading.  
This product must be grounded.  
Grounding installation decreases the risk of  
electric shock by opening a path with low  
resistance for the electricity flow in case of  
a malfunction or failure. Power cable of this  
product is equipped with a conductor and  
a grounding plug that allows for grounding  
the product. This plug must be installed  
appropriately and inserted into a socket  
which is grounded in accordance with the  
local laws and regulations.  
Never operate your dryer without the  
lint filter installed.  
Do not allow fibre, dust and dirt  
accumulation around the exhaust exit and  
at adjacent areas.  
Power cable plug must be within easy  
reach after installation.  
Do not use extension cords, multi-plugs  
or adaptors to connect the dryer to power  
supply in order to decrease the risk of  
electric shock.  
Do not install the product behind a door  
with a lock, sliding door or a door that has  
a hinge against the hinge of the dryer.  
Do not install or leave this product in  
places where it will be exposed to outdoor  
conditions.  
Do not make any changes on the plug  
supplied with the product. If it is not  
compatible with the socket, have a  
qualified electrician change the socket with  
a suitable one.  
Do not tamper with the controls.  
Items cleaned or washed with gasoil/  
fuel oil, dry-laundry solvents and other  
combustible or explosive materials as  
Do not perform any repair or part replacing  
procedures on the product even if you  
Download from Www.Somanuals.c3om.EANll Manuals Search And Download.  
know or have the ability to perform unless  
it is clearly suggested in the operating  
instructions or the published service  
manual.  
using the On/Off button. In cases when  
the On/Off button is on (while the dryer  
is energized), keep the door of the dryer  
closed.  
Inside and exhaust duct of the product  
must be cleaned by the qualified service  
personnel periodically.  
Intended use  
This product has been designed for  
domestic use. It should not be used for  
other purposes.  
Wrong connection of grounding conductor  
of the product can cause electric shock. If  
you have any suspect about the grounding  
connection, have it checked by a qualified  
electrician, service representative or service  
personnel.  
Do not reach into the machine when the  
drum is spinning.  
Unplug the machine when it is not in use.  
Never wash down the appliance with  
water! There is the risk of electric shock!  
Always disconnect by unplugging from the  
mains before cleaning.  
Never touch the plug with wet hands.  
Never unplug by pulling on the cable,  
always pull out by grabbing the plug only.  
Do not operate the machine if the power  
cable or plug is damaged!  
Never attempt to repair the machine  
yourself, otherwise, you will be putting your  
life and others’ lives in danger.  
For malfunctions that cannot be solved by  
following the information given in the safety  
instructions:  
Turn off the machine, disconnect the  
power cord and contact an Beko Service.  
Do not stop the dryer before the drying  
cycle comes to an end unless you  
will remove all laundry from the dryer  
immediately in order to lay them and  
dissipate the heat.  
Remove the door of the drying  
compartment before decommissioning or  
disposing of the product.  
Use the product only for drying laundry that  
are marked accordingly.  
Dry only those articles in your product that  
are stated in this manual.  
This product is not intended to be used by  
persons with physical, sensory or mental  
disorders or unlearned or inexperienced  
people (including children) unless they  
are attended by a person who will be  
responsible for their safety or who will  
instruct them accordingly for use of the  
product.  
Children’s safety  
Electrical appliances are dangerous for  
the children. Keep children away from the  
machine when it is operating. Do not let  
them tamper with the machine.  
Packaging materials are dangerous to  
children. Keep the packaging materials out  
of reach of children or dispose them by  
classifying according to waste directives.  
Do not allow children sit/climb on or enter  
in the product.  
Children should be supervised to ensure  
that they do not play with the product.  
Close the loading door when you leave the  
area where the product is located.  
The final step of the drying cycle (cool-  
down cycle) occurs without applying  
heat to ensure that the items are left at a  
temperature that will not damage them.  
Fabric softeners or similar products should  
be used as specified by the fabric softener  
instructions.  
Underwear that contains metal  
reinforcements should not be placed in  
a dryer. Damage to the dryer can result if  
metal reinforcements come loose during  
drying.  
Check all garments for forgotten lighters,  
coins, metal pieces, needles, etc. before  
loading.  
Remove all objects from pockets such as  
lighters and matches.  
At times when your dryer is not in use or  
after the laundry is taken out following the  
completion of drying process, turn off by  
Download from Www.Somanuals.c4om.EANll Manuals Search And Download.  
2 Installation  
It is the customers responsibility to arrange a  
suitably qualified installer to correctly install this  
product.  
placed on top of a washing machine, the  
approximate weight of both machines may  
reach 180 kg when they are full. Therefore,  
the floor must be capable of carrying the  
load on it!  
CPreparation of location and electrical  
installation for the product is under  
customers responsibility.  
Ventilation hose and connection (for  
products equipped with an outlet  
vent)  
BInstallation and electrical connections must  
be carried out by a qualified personnel.  
APrior to installation, visually check if the  
product has any defects on it. If so, do not  
have it installed. Damaged products will  
cause risks for your safety.  
Ventilation hose allows exhaust air from inside  
the machine  
Vented dryer has 1 air outlet.  
Stainless sheet metal or aluminum pipes can  
be used instead of a hose. The pipe diameter  
should be minimum 10 cm.  
Appropriate installation location  
Install the product in an environment which  
has no risk of freezing and is in a stable  
and level position.  
Maximum hose and pipe lengths are given in  
the table below.  
Operate your product in a well ventilated,  
dust-free environment.  
Hose  
4 m  
-1.0 m  
-1.8 m  
Pipe  
Do not block the air ducts in front of and  
under the product with materials such as  
long pile rugs and wooden planks.  
Do not place your product on a long pile  
rug or on similar surfaces.  
Maximum length  
1 elbow 45°  
1 elbow 90°  
1 elbow 90° short  
1 wall passage  
5 m  
-0.3 m  
-0.6 m  
-2.7 m  
-2.0 m  
Do not install the product behind a door  
with a lock, sliding door or a hinged door  
which can strike the product.  
-2.0 m  
CEach elbow and other passages should  
be subtracted from the maximum length  
stated above.  
Once the product is installed, it should stay  
at the same place where its connections  
have been made. When installing the  
product, make sure that the rear wall of it  
does not touch anywhere (tap, socket, etc.)  
and also pay attention to install the product  
at a place where it will stay permanently.  
To connect a ventilation hose;  
1. Connect the air outlet hose to the  
hose spacer piece by turning it  
counterclockwise.  
2. Make the hose passages as shown below.  
CExhaust of humid air from the dryer into the  
room is inconvenient. It may damage the  
walls and furniture in the room.  
BDo not place the product on top of the  
power cable.  
Keep at least 1.5 cm distance to walls of  
other furniture.  
CThe ventilation hose can be routed outdoors  
via a window or it can be connected to the  
air outlet in the bathroom.  
CAir outlet hose must be routed directly to the  
outdoors. There must be a limited number  
of elbows as not to hinder ventilation.  
CTo prevent water accumulation in the hose,  
make sure that it is not folded on the floor.  
Under counter installation  
A special part (Part no: 295 970 0100)  
replacing the top trim must be provided  
and installed by the suitably qualified  
installer in order to use the machine under  
a counter or in a cupboard. It should never  
be operated without the top trim.  
Leave at least 3 cm of space between  
the side and rear walls of the product and  
the walls of the counter/cupboard when  
installing your product under a counter or in  
a cupboard.  
Mounting over a washing machine  
A fitting device should be used between  
the two machines when installing above a  
washing machine. The bracket (Part no.  
296 280 0100 white/296 280 0200 grey)  
must be installed by the Authorised Service  
Agent.  
Place the product on a firm floor. If it will be  
Download from Www.Somanuals.c5om.EANll Manuals Search And Download.  
Do not make connections via extension  
cables or multi-plugs.  
BThe ventilation hose should not be  
connected to the chimney of a stove or a  
fireplace.  
BDo not operate your product at the same  
time with heaters such as a coal or gas  
stove. Airflow may cause the chimney to  
flare up.  
The main fuse and switches must have a  
contact distance of minimum 3 mm.  
BDamaged power cable must only be  
replaced by a qualified electrician.  
BIf the product is faulty, it must not be  
operated unless it is repaired! There is the  
risk of electric shock!  
Adjusting feet  
In order to ensure that your product operates  
more silently and vibration-free, it must stand  
level and balanced on its feet. Front feet of your  
product can be adjusted. Balance the machine  
by adjusting the feet.  
First use  
To have the product ready for operation  
before calling the suitably qualified installer,  
make sure that its location and power  
supply installations are appropriate. If they  
are not, call a qualified electrician to have  
any necessary arrangements carried out.  
Make sure that the power connections of  
the product are in accordance with the  
instructions given in relevant chapters of  
this manual.  
Disposing of packaging material  
Packaging materials are dangerous to children.  
Keep packaging materials in a safe  
place out of reach of children. Packaging  
materials of your product are manufactured  
from recyclable materials. Sort and dispose  
of them in accordance with recycled waste  
instructions. Do not dispose of them with  
normal domestic waste.  
1. Loosen the feet by hand.  
2. Adjust the feet until the product stands level  
and firmly on the floor.  
CDo not use any tools to loosen the  
adjustable feet, otherwise, they can be  
damaged.  
CNever remove the adjustable feet from their  
Transportation of the machine  
1. Unplug the machine from the mains.  
2. Remove the water drain (if any) and  
chimney connections.  
housings.  
2 plastic pieces supplied along with the user  
manual prevent your machine from slipping on  
wet and slippery surfaces. To install the plastic  
parts:  
3. Drain water remaining in the machine  
completely before transportation.  
1. Tilt your product to backwards.  
2. Fit the plastic parts on to the front  
adjustable feet. Press on the plastic parts  
to snap them into their seating.  
3. Check the balance of your product  
again and readjust the adjustable feet if  
necessary.  
Disposing of the old machine  
Dispose of your old machine in an  
environmentally friendly manner.  
Refer to your local dealer or solid waste  
collection centre in your area to learn how to  
dispose of your machine.  
Before disposing of your old machine, cut off  
the power cable plug and make the loading  
door lock unusable to avoid dangerous  
conditions to children.  
Electrical connection  
Connect the machine to a grounded outlet  
protected by a fuse of suitable capacity as  
stated in the technical specifications table. Our  
company shall not be liable for any damages  
that will arise when the machine is used on a  
circuit without grounding.  
Connection must comply with national  
regulations.  
If the current value of the fuse or breaker  
in the house is less than 10 Amps, have a  
qualified electrician install a 10 Amp fuse.  
Power cable plug must be within easy  
reach after installation.  
The voltage and allowed fuse or breaker  
protection are specified in the “Technical  
Specifications” section.  
The specified voltage must be equal to  
your mains voltage.  
Download from Www.Somanuals.c6om.EANll Manuals Search And Download.  
Technical Specifications  
EN  
2
Height (adjustable)  
Width  
84,6 cm  
59,5 cm  
53 cm  
7 kg  
Depth  
Capacity (max.)  
Weight (net)  
32 kg  
Voltage  
Rated power input  
Model code  
See type label  
Type label is located behind the loading door.  
Download from Www.Somanuals.c7om.EANll Manuals Search And Download.  
3 Initial preparations for drying  
Things to be done for energy saving:  
Make sure that you operate the product  
at its full capacity but pay attention to not  
exceeding it.  
Spin your laundry at the highest speed  
possible when washing them. Thus,  
the drying time is shortened and energy  
consumption is decreased.  
Pay attention to dry same types of laundry  
together.  
Follow the instructions in the user manual  
for programme selection.  
A B C D  
Low  
l n m  
o p q  
Make sure that sufficient clearance is  
provided at the front and rear side of the  
dryer for air circulation. Do not block the  
grill at the front side of the product.  
Do not open the door of the machine  
during drying unless necessary. If you must  
certainly open the door, pay attention not  
to keep it open for a long time.  
Laundry unsuitable for drying in the  
machine  
Laundry items with metal attachments  
such as belt buckles and metal buttons  
can damage your dryer.  
Do not add new (wet) laundry during  
drying.  
Do not dry items such as woollens, silk  
garments and nylon stockings, delicate  
embroidered fabrics, laundry with metal  
accessories and items such as sleeping  
bags in the dryer.  
Lint and fibres released from the laundry to  
the air during the drying cycle are collected  
in the “Lint Filter”. Make sure that you  
clean the filters before or after each  
drying.  
Laundry items made of delicate and  
valuable fabrics as well as lace curtains can  
be creased. Do not dry them in the dryer!  
Do not dry items made of hermetic fibres  
such as pillows and quilts in the dryer.  
Laundry items made of foam or rubber will  
be deformed.  
Do not dry laundry items containing rubber  
in the dryer.  
Do not dry laundry items exposed to  
petroleum, oil, combustible or explosive  
agents in the dryer even if they are washed  
beforehand.  
Overly wet laundry or laundry with dripping  
water must not be put into the dryer.  
Items which are cleaned or washed with  
gasoil/fuel oil, dry-laundry solvents and  
other combustible or explosive materials  
as well as the items that are contaminated  
or spotted with such materials should not  
be dried in the product since they emit  
flammable or explosive vapor.  
Do not dry items cleaned with industrial  
chemicals in the dryer.  
Do not dry your unwashed laundry in the  
dryer.  
In models with condenser, make sure that  
you clean the condenser regularly at  
least once every month or after every  
30 drying cycles.  
In vented models, follow the chimney  
connection rules in the user manual and  
pay attention to the chimney cleaning.  
Ventilate the room, where the dryer is  
located, well during drying.  
“For power saving in models with lamps, at  
times when your dryer is not in use, keep  
the door closed if the On/Off button is  
pressed (if the dryer is energized).”  
Laundry suitable for drying in the  
machine  
CAlways follow the suggestions on the  
laundry labels. Dry only the laundry having  
a label stating that they are suitable for  
drying in a dryer and make sure that you  
select the appropriate programme.  
Items soiled with cooking oils, acetone,  
alcohol, fuel oil, kerosene, stain remover,  
turpentine, paraffin and paraffin removers  
must be washed in hot water with plenty of  
detergent before being dried in the dryer.  
Download from Www.Somanuals.c8om.EANll Manuals Search And Download.  
Garments or pillows bolstered with rubber  
foam (latex foam), shower bonnets, water  
resistant textiles, materials with rubber  
reinforcement and rubber foam pads  
should not be dried in the dryer.  
Do not use fabric softeners and anti-static  
products unless they are recommended by  
the manufacturers of the fabric softener or  
the product.  
Do not dry the underwear reinforced with  
metal parts in the dryer. If these metal  
reinforcements loosen and break during  
drying, they will damage your dryer.  
can be damaged.  
CPlace your laundry into the drum loosely so  
that they will not get tangled.  
CLarge pieces (E.g.: bed sheets, quilt covers,  
large tablecloths) may bunch-up. Stop the  
dryer 1-2 times during drying process to  
separate bunched-up laundry.  
Following weights are given as examples.  
Approximate  
weights (g)  
Home articles  
Cotton quit covers (double)  
Cotton quit covers (single)  
Bed sheets (double)  
Bed sheets (single)  
Large tablecloths  
Small tablecloths  
Tea napkins  
1500  
1000  
500  
350  
700  
250  
100  
700  
350  
Preparing laundry for drying  
• Check all laundry items before loading  
them into the product to make sure that  
there are no lighters, coins, metal items,  
needles and etc. in their pockets or on any  
part of them.  
Fabric softeners and similar products  
must be used in accordance with the  
instructions of the manufacturer of the  
relevant products.  
All laundry must be spun at the highest  
spin speed that your washing machine  
allows for the laundry type.  
Laundry may be tangled after washing.  
Separate your laundry before placing them  
into your dryer.  
Sort your laundry according to their types  
and thicknesses. Dry the same type of  
laundry together. E.g.: fine kitchen towels  
and table cloths dry faster than the thick  
bath towels.  
Bath towels  
Hand towels  
Approximate  
weights (g)  
Garments  
Blouses  
150  
300  
200  
500  
350  
700  
100  
125  
Cotton shirts  
Shirts  
Cotton dresses  
Dresses  
Jeans  
Correct load capacity  
Handkerchiefs (10 pieces)  
T-Shirts  
Loading  
Open the loading door.  
Place laundry items loosely into the dryer.  
Push the loading door to close. Ensure that  
no items are caught in the door.  
AConsider the information in the “Programme  
Selection Table”. Always start the  
programme in accordance with the  
maximum load capacity.  
CAdding laundry to the machine more  
than the level shown in the figure is not  
recommended. Drying performance will  
degrade when the machine is overloaded.  
Furthermore, your dryer and your laundry  
Download from Www.Somanuals.c9om.EANll Manuals Search And Download.  
4 Selecting a Programme and OperatingYour Machine  
Control panel  
1
3
2
4
Shirts  
Mini  
Jeans  
Ready to  
Iron  
Delicates  
Synthetics  
Ready to  
Wear  
Clean  
Filter  
Freshen Up  
60 min.  
Drying  
Start/  
Pause  
3h  
6h  
9h  
Time  
Delay  
Ready to  
Iron  
Ready to  
Iron  
Ready to  
Ready to  
Wear  
Ready to  
Wear  
Plus  
Wear  
40 min.  
End /  
Anticrease  
Buzzer Cancel  
Reset 3’’  
On / Off  
20 min.  
10 min.  
Extra dry  
Timer  
Programmes  
Cottons  
6
7
5
1. Filter cleaning warning light  
5. Programme selection knob  
Used to select a programme.  
6. Start/Pause/Cancel button  
Used to start, pause or cancel the programme.  
7.Time delay selection button  
Used to set the time delay.  
Warning light turns on when the filter is full.  
2. Program follow-up indicator  
Used to follow-up the progress of the current  
programme.  
3. Cancel audio warning  
Used to cancel the audio warning given at the end  
of the programme.  
4. On/Off button  
Used to turn on and off the machine.  
Download from Www.Somanuals1.c0om.EANll Manuals Search And Download.  
Preparing the machine  
laundry from creasing will be activated if  
you do not take the laundry out after the  
programme is over. This programme rotates  
the laundry in 10-minute intervals to prevent  
creasing.  
1. Plug in your machine.  
2. Place the laundry in the machine.  
3. Press the “On/Off” button.  
CPressing the “On/Off” button does not  
necessarily mean that the programme has  
started. Press "Start/Pause/Cancel" button  
of the machine to start the programme.  
Programme selection  
Special programmes  
For special cases, there are also extra  
programmes available:  
CAdditional programmes may differ  
according to the model of your machine.  
•Mini  
Decide the appropriate programme from  
the table below which includes drying  
temperatures in degrees. Select the desired  
programme with the programme selection  
button.  
You can use this programme to dry the cottons  
that are spun at high speeds in your washing  
machine. It can dry your 1,2 kg Cotton laundry  
(3 Shirts / 3 T-Shirts) within 30 minutes.  
CIn order to obtain better results from the  
dryer programs, your laundry must be  
washed with suitable program and spun  
at the recommended spin speeds in your  
washing machine.  
Dry at high temperature only  
for cotton laundry. Thick and  
multi layered laundry (E.g.:  
Extra dry  
towels, linens, jeans) are dried  
in a way that they do not  
require ironing before placing  
in the wardrobe.  
•Shirt  
Dries the shirts in a more sensitive way so that  
they are less creased and ironed easily.  
CShirts may contain little amount of  
dampness at the and of the program. It is  
advised not to leave the shirts in the dryer.  
•Jeans  
Normal laundry (E.g.:  
tablecloths, underwear) are  
Ready to  
dried in a way that they do not  
wear  
require ironing before placing  
in the drawers.  
You can use this program to dry the jeans  
that are spun at high speeds in your washing  
machine.  
Normal laundry (E.g.:  
tablecloths, underwear) are  
dried in a way that they do not  
Ready to  
CReview the relevant part of the program  
require ironing before placing  
wearPlus  
table.  
in the drawers, but more  
than those in the ready to  
wearoption.  
•Delicates  
You can dry at a lower temperature your very  
delicate laundry (silk blouses, fine underwear,  
etc.) that are suitable for drying or laundry  
which is advised to be hand-washed.  
CIt is recommended to use a cloth bag  
to avoid certain delicate garments and  
laundry from getting creased or damaged.  
Take your garments immediately out of the  
dryer and hang them after the programme  
ends in order to prevent them being  
creased.  
Normal laundry (E.g., Shirts,  
dresses) are dried ready to be  
ironed.  
Iron Dry  
C For further program details, see, “Program  
Selection Table”  
Main programmes  
Depending on the type of laundry, the following  
main programmes are available:  
•Cottons  
•Ventilation  
You can dry your durable laundry with this  
programme. Dries at high temperature. It is  
recommended to use for your cotton items  
(such as bed sheets, quilt cover, underclothing,  
etc.).  
Only ventilation is performed for 10 minutes  
without blowing hot air. You can air your  
clothes that have been kept at closed  
environments for a long time thanks to this  
program to deodorize unpleasant odors.  
•Timer programs  
•Synthetics  
You can dry your less durable laundry with this  
programme. It dries at a lower temperature  
compared to the cottons programme. It is  
recommended for your synthetic laundry (such  
as shirts, blouses, synthetic/cotton blended  
laundry, etc.).  
You can select one of the 10 min., 20 min.,  
40 min. and 60 min. timer programmes to  
achieve the desired final drying level at low  
temperatures. Programme dries at the selected  
time regardless of the drying temperature.  
C Do not dry curtains and lace in your  
machine.  
•Anti-creasing  
A 2-hour anti creasing programme to prevent  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11 EN  
Program selection and consumption table  
2
EN  
Approximate  
amount of  
remaining  
humidity  
Capacity  
(kg)  
Spin speed in washing  
machine (rpm)  
Drying time  
(minutes)  
Programs  
Cottons / Coloreds  
1200-1000  
900-800  
% 60  
% 70  
% 60  
% 70  
% 60  
% 70  
% 60  
% 70  
% 60  
% 70  
% 60  
% 70  
%50  
135  
150  
75  
7
3.5  
7
Ready to Wear  
A
A
A
1200-1000  
900-800  
90  
1200-1000  
900-800  
140  
160  
85  
Ready to Wear Plus  
1200-1000  
900-800  
3.5  
7
100  
100  
115  
60  
1200-1000  
900-800  
Ready to Iron  
1200-1000  
900-800  
3.5  
75  
Mini  
1.2  
1.5  
1200-1000  
1000-800  
30  
Shirt  
%50  
49  
Jeans  
4
1200-1000  
%50  
100  
Synthetics  
800  
600  
800  
600  
% 40  
% 50  
% 40  
% 50  
55  
70  
35  
45  
3.5  
Ready to Wear  
B
1.75  
Delicates  
Ready to Wear  
1.5  
600  
% 50  
40  
B
Energy consumption values  
Program  
Energy consumption value kWh  
per year  
Energy rating  
star  
Capacity  
(kg)  
Cottons-Ready to Wear Plus*  
7
305  
2.0  
* : Energy Label standard program (AS/NZS 2442)  
All values given in the table have been fixed according to standard laboratory conditions. These  
values may deviate from the table according to the laundry type, laundry spin speed, environmental  
conditions and voltage fluctuations.  
Download from Www.Somanuals1.c2om.EANll Manuals Search And Download.  
2. Light of the “Start/Pause/Cancel” button  
will turn on to indicate that the programme  
has started.  
Auxiliary function  
Cancel audio warning  
Your dryer will give an audio warning when the  
programme comes to an end. If you do not  
want to hear the audio warning, press “Cancel  
Audio Warning” button. The relevant light  
will turn on when this button is pressed and  
an audio warning will not be given when the  
programme comes to an end.  
Progress of program  
Progress of a running program is shown  
through the program follow-up indicator.  
At the beginning of every program step, the  
relevant indicator LED will light up and light of  
the completed step will turn off.  
“Drying”:  
CYou can select this function either before or  
- Drying level will be illuminated during the  
whole drying process until the drying degree  
reaches “iron dry”.  
after the programme starts.  
Warning indicators  
CWarning indicators may differ according to  
the model of your dryer.  
“Iron Dry”:  
- Starts to illuminate when the drying degree  
reaches “iron dry” step and remains illuminated  
until the next step.  
Filter cleaning  
A warning light will turn on to remind filter  
cleaning after the programme finishes.  
CIf the filter cleaning warning light lights up  
continuously, please refer to, “Suggested  
solutions for problems”.  
“Ready to wear”:  
Starts to illuminate when the drying degree  
reaches “Ready to wear” step and remains  
illuminated until the next step.  
Time delay  
“Final / Anti-creasing”:  
If you wish to dry your clothes at a later time,  
thanks to the time delay function, you can  
delay the program start up to 3 hours, 6 hours  
or 9 hours.  
- Illuminates when the program comes to an  
end and anti-creasing function is activated.  
CIf more than one LED light up or  
flash concurrently, it means there is  
malfunctioning or a failure (please see,  
Solution suggestions for problems).  
1. Open the loading door and put the laundry  
in.  
CMake sure that all air outlets are open,  
door filter is cleaned and the water tank is  
empty.  
Changing the programme after it has  
started  
2. Set the drying program and, if required, the  
auxiliary functions.  
You can use this feature to dry your clothes  
under higher or lower temperatures after your  
dryer has started.  
3. When the time programming button is  
pressed once, a 3 hour delay is selected  
and the relevant led lights. When the same  
button is pressed again, 6 hours; and if  
pressed once more, 9 hours delay will be  
selected. If the time programming button  
is pressed one more time, time delaying  
function will be cancelled. Set the time  
delay as you require.  
For example;  
1. Press and hold the “Start/Pause/Cancel”  
button for about 3 seconds to “Cancel”  
the programme in order to select “Extra  
Dry” programme instead of “Iron Dry”  
programme.  
2. Select the “Extra Dry” programme by  
rotating the programme selection button.  
3. Press “Start/Pause/Cancel” button to start  
the programme.  
4. Delayed operation of the selected program  
is started by pressing the "Start/Pause/  
Cancel" button after selecting the time  
delay.  
CPress “Start/Pause/Cancel” button for 3  
seconds to cancel the programme or turn  
the programme selection knob in any  
direction to end the programme while the  
machine is running. Water tank and filter  
cleaning warning lights turn on to warn the  
user when the programme is cancelled by  
pressing the “Start/Pause/Cancel” button  
for 3 seconds. However, the warning  
lights do not turn on when the programme  
is cancelled by turning the programme  
selection knob. Only the drying light turns  
on and the machine remains in hold until  
a new programme is selected and the  
“Start/Pause/Cancel” button is pressed.  
CAdditional laundry may be loaded / taken  
out during the time delay period.  
CDuring the time delay period, laundry is  
rotated for 4 seconds in every 10 minutes  
to prevent creasing.  
Canceling the time delay  
If you want to cancel the time delay countdown  
and start the program:  
1. Press “Start/Pause/Cancel” button for  
about 3 seconds.  
2. Press “Start/Pause/Cancel” button to start  
the program right away.  
Starting the programme  
1. Press “Start/Pause/Cancel” button to start  
the programme.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13 EN  
Child-proof lock of the machine should not  
be active in order to perform these two  
operations. If the child-proof lock is active,  
deactivate it before performing these  
operations.  
programme selection knob while the child-  
proof lock is active. Press the buttons for 3  
seconds to deactivate the child-proof lock.  
Single beep will be heard and child-proof  
lock will be deactivated.  
Adding/removing laundry in standby mode  
In order to add or remove laundry after the  
programme starts:  
AA double beep will be heard if you turn  
the programme selection knob when the  
machine is running and the child-proof  
lock is active. If you deactivate the child-  
proof lock without returning the program  
selection knob to its previous position, the  
programme will be terminated since the  
position of the programme selection knob  
is changed. The drying light turns on and  
the machine remains on hold until a new  
programme is selected and the “Start/  
Pause/Cancel” button is pressed.  
Finishing by canceling the programme  
To cancel any selected programme:  
Press “Start/Pause/Cancel” button for about  
3 seconds. The “Filter cleaning”, “Water tank”  
and “End/ Anti-creasing” warning lights will  
turn on at the end of this period for reminding  
purposes.  
1. Press the “Start/Pause/Cancel” button to  
switch the dryer to “Pause” mode. Drying  
process will stop.  
2. Open the door at “Pause” position and  
close it again after adding or taking out  
laundry.  
3. Press “Start/Pause/Cancel” button to start  
the programme.  
CAny laundry added after the drying process  
has started may cause the dried clothes in  
the machine intermingle with wet clothes  
and the result will be wet laundry after the  
drying process is over.  
CLaundry may be added or taken out  
as much as desired during a drying  
process, but this process will extend the  
programme duration and increase energy  
consumption since the drying will be  
interrupted continuously. Therefore, it is  
recommended to add laundry before the  
drying programme has started.  
AAs the inside of the dryer will be excessively  
hot when you cancel the programme while  
the dryer is running, activate the ventilation  
programme to cool it down.  
End of programme  
Child-proof lock  
The “End/Anti-creasing”, “Filter cleaning” and  
“Water tank” warning lights on the programme  
follow up indicator will turn on when the  
programme comes to an end. The door can be  
opened and the machine becomes ready for a  
second cycle.  
There is a child-proof lock to prevent any  
programme interruption due to the pressing  
of button while the programme is running.  
The loading door and all buttons except the  
“On/Off” button on the control panel are  
deactivated when the child-proof lock is active. Press “On/Off” button to turn off the dryer.  
Press the “Start/Pause/Cancel” and “Cancel  
audio warning” buttons simultaneously for 3  
seconds to activate the child-press lock.  
To start a new programme after the  
programme is over or to interrupt the  
programme, the child-proof lock should be  
deactivated. Press the same buttons for 3 sec.  
again to deactivate the child-proof lock.  
CChild-proof lock is deactivated when the  
machine is restarted by pressing the On/  
Off button.  
CFinal step of the drying cycle (cooling step)  
is performed without heat application in  
order to keep the items at a temperature  
that would not harm them.  
CA 2-hour anti creasing programme to  
prevent laundry from creasing will be  
activated if you do not take the laundry out  
after the programme has come to an end.  
CIf you will not take the laundry out  
immediately, do not stop the dryer before  
the drying process is complete.  
CClean the filter after each drying (please see,  
Filter cleaning).  
CDrain the water tank after each drying  
(please see, Water tank)  
CPress the relevant buttons for 3 seconds  
to activate the child-proof lock. A long  
beep will be heard and the child-proof lock  
will be activated. A double beep will be  
heard if you press any button or turn the  
Download from Www.Somanuals1.c4om.EANll Manuals Search And Download.  
5 Maintenance and cleaning  
Filter Cartridge / Door Inner Surface  
Lint and fibres released from the laundry to the  
air during the drying cycle are collected in the  
“Filter Cartridge”.  
Sensor (models equipped with a  
sensor)  
There are humidity sensors in your machine  
that detect whether the laundry is dry or not.  
For sensor cleaning;  
1. Open the door of the machine.  
2. Allow the machine to cool off if drying has  
been carried out.  
CSuch fibre and lint are generally formed  
during wearing and washing.  
CAlways clean the filter and the inner  
surfaces of the cover after each drying  
process.  
3. Wipe the metal sensors with a soft cloth,  
dampened with vinegar and dry them.  
C Clean metal sensors 4 times a year.  
A Never use solvents, cleaning agents or  
substances alike when cleaning as these  
might cause fire and explosion!  
CYou can clean the filter and filter area by  
vacuum cleaner.  
To clean the filter:  
1. Open the loading door.  
2. Remove the cover filter by pulling it up and  
open the filter.  
3. Clean lint, fibre, and cotton raveling by  
hand or with a soft piece of cloth. 4.  
Close the filter and place it back into its  
seat.  
C Clogging may arise on the filter surface  
after using your machine for some time; if  
this occurs, wash the filter with water and  
dry it before using again.  
C Clean the entire inner surface of the cover  
and door gasket.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15 EN  
6 Solution suggestions for problems  
Drying process takes too much time  
The filter mesh may be clogged. Wash with water.  
Laundry come out wet at the end of drying.  
The filter mesh may be clogged. Wash with water.  
Excessive laundry might have been loaded in. Do not overload the machine.  
Machine does not switch on or the program does not start. Machine is not activated when set.  
It might have not been plugged in. Make sure that the machine is plugged in.  
The loading door may be ajar. Make sure that the loading door is properly closed.  
Program might have not been set or the «Start/Pause/Cancel» button might have not been  
pressed. Make sure that the program has been set and it is not in “Pause” mode.  
«Childproof lock» might have been activated. Deactivate the childproof lock.  
The condenser cover on the models with a condenser might not be closed securely. Make  
sure that the condenser cover and the red lock is closed securely.  
Program has been interrupted without any cause.  
The loading door may be ajar. Make sure that the loading door is properly closed.  
Electricity may be cut off. Press «Start/Pause/Cancel» button to start the program.  
The condenser cover on the models with a condenser might not be closed securely. Make  
sure that the condenser cover and the red lock is closed securely.  
Laundry has shrunk, become felted or deteriorated.  
A program suitable for the laundry type might have not been used. Dry only the laundry  
which is suitable for drying in your machine after checking the labels on your clothes.  
Select a program with suitable low temperature for the laundry type to dry your clothes.  
Drum lighting does not come on. (for models equipped with a lamp)  
The machine might have not been started by using the On/Off button. Make sure that the  
machine is On.  
Bulb may have blown. Call Beko service to arrange for the bulb to be replaced.  
The condenser cover on the models with a condenser might not be closed securely. Make  
sure that the condenser cover and the red lock is closed securely.  
2 beeps heard when the buttons are pressed or the program selection knob is turned.  
Childproof lock» might have been activated. Deactivate the childproof lock.  
Program selection knob might be turned to an undefined position. Select one of the  
defined programs.  
“Filter cleaning” light is flashing.  
Filter might have not been cleaned. Clean the cover filter.  
“Final / Anti-creasing” LED is on.  
Program has come to an end. Turn off the machine and take out the laundry.  
3 beeps are heard when you press the Start/Pause/Cancel button  
The loading door may be ajar. Make sure that the machine is plugged in.  
Make sure that the condenser cover and the red lock is closed securely.  
Also for products equipped with a condenser:  
“Water tank” warning LED is flashing.  
Water may be full.  
Drain the water in the water tank.  
APlease call Beko Service if the problem persists.  
Download from Www.Somanuals1.c6om.EANll Manuals Search And Download.  

3Com Network Router NETBuilder SI User Manual
A4 Tech Digital Camera PK 5 User Manual
ADC Network Card FL1000 User Manual
Agilent Technologies Mouse 66001A User Manual
Aiphone Intercom System IC 1ADU User Manual
Alliance Laundry Systems Clothes Dryer T453I User Manual
American Standard Outdoor Shower T675500 User Manual
ATON Stereo Amplifier A275 User Manual
Audiovox Car Stereo System AV303 User Manual
Beko Ventilation Hood CWB 9601 X User Manual