User Manual
STUDIO CONDENSER
MICROPHONE
Studio Condenser Microphone
Download from Www.Somanuals.com. All Manuals Search And Download.
3
STUDIO CONDENSER MICROPHONE C-1 User Manual
1. Power Supply
Your condenser mic C-1 needs a phantom power supply (+36 to +52 V). If your
C-1 is connected to a microphone preamp and supplied with phantom power,
the LED on the microphone lights up. BEHRINGER assumes no liability for any
damage caused by a defective phantom power supply. Always mute the sound
reinforcement system before you switch on the phantom power supply.
2. Directivity
Your C-1 features a capsule with a cardioid pickup pattern and is ideal for
recording individual instruments, vocals and speech. Cardioid pickup pattern
means that the sound produced by sources located in front of the mic is strongly
picked up. It is often used in recording situations, since this directivity pattern
tones down the pickup of sounds located to the back of the microphone.
3. Microphone Installation
There is an adapter on your microphone that lets you mount it on mic stands with
either metric (Europe) or imperial-gauge threads (North America). First dismantle
the microphone from the stand mount adapter by detaching the fine-thread
shoulder screw at the bottom end of the microphone. Fasten the adapter onto
the microphone stand, place the microphone into it and tighten the screw again.
Basically, the microphone in the stand mount adapter should stand upright
and face the sound source at a right angle. The angle of the microphone to the
sound source influences the sound of the recording; therefore, experiment with
different positions until you achieve the desired sound. To this end, you can
rotate the mic in the stand mount adapter by loosening the screw somewhat
and tightening it again.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
STUDIO CONDENSER MICROPHONE C-1 User Manual
If necessary, you can bend the microphone out of its vertical position by using the
hinge on the microphone stand.
◊
Please make sure to handle the microphone shaft with attention and
care to avoid damaging the screw thread. In no situation should you
ever apply excessive force.
Of course, you can detach the C-1 from the stand mount adapter and attach it to a
commercially available suspension mount.
4. Audio Connection
Use a balanced XLR microphone cable with the following pin assignment:
pin 1 = shielding; pin 2 = +; pin 3 = -. Since your C-1 features gold-plated
contact points throughout, we recommend that you use only microphone cables
with gold-plated connectors.
5. Level Setting/Adjusting the Basic Sound
Adjust the gain control in the microphone channel of your mixing console so that
the peak LED lights up only occasionally or never at all. The EQ controls in the
microphone channel should be set to mid-travel position to start with. To get
the sound you want, try changing the mic position relative to the sound source
or even move the microphone around in the recording room of your studio.
Adjusting the angle at which walls face the sound source can also be helpful.
Only when the desired basic sound has been achieved, should you start to use
equalizers and signal processors, if any at all (remember: less is often more!)
Due to the extremely linear frequency response and the high sonic resolution of
your C-1, there is no need for high-frequency “EQing” that can heavily influence
the signal and unnecessarily increase the noise level. The C-1 provides that
much-desired transparency which often gets lost during recording and mixing.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
STUDIO CONDENSER MICROPHONE C-1 User Manual
0°
0 dB
340°
20°
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
320°
40°
300°
60°
280°
80°
-35 dB
-40 dB
260°
100°
240°
120°
140°
220°
160°
200°
180°
1kHz
Polar pattern
dB
20.0
10.0
0.0
-10.0
-20.0
20.0
100.0
1000.0
10k 20k Hz
Frequency response
Download from Www.Somanuals.com. All Manuals Search And Download.
6
STUDIO CONDENSER MICROPHONE C-1 User Manual
6. Specifications
Transducer type
condenser, 16 mm
Polar pattern
cardioid
Connection:
gold-plated balanced XLR connector
Open circuit sensitivity
Frequency response
Max. SPL (1% THD @ 1 kHz)
Nominal impedance
Load impedance
-33 2 dBV (0 dBV = 1 V/Pa)
40 Hz - 20 kHz
136 dB
100 Ω
>1 kΩ
Mains Voltage / Fuse
Supply voltage
+36 - 52 V
2.5 mA
Supply current
Physical/Weight
Dimensions
Ø shaft: 54 mm
length: 169 mm
Weight
approx. 0.45 kg
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|