Barco Projector PGWU 62L K User Manual
User manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changes  
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to  
the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or  
changes to the product(s) and/or the program(s) described in this publication at any time without notice.  
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the  
information in this publication; these changes are incorporated in new editions of this publication.  
The latest edition of Barco manuals can be downloaded from the Barco web site  
www.barco.com or from the secured Barco web site https://my.barco.com.  
Copyright ©  
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded,  
transmitted or stored in a retrieval system without the prior written consent of Barco.  
EN55022/CISPR22 Class A ITE (Information Technology Equipment)  
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such  
equipment should not be restricted in its sale but the following warning shall be included in the instructions for use:  
Warning :This is a class A product. In a domestic environment this product may cause radio interference in which case  
the user may be required to take adequate measures.  
Federal Communications Commission (FCC Statement)  
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the  
FCC rules.  
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated  
in a commercial environment.This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area may cause harmful interference, in which case the user will be  
responsible for correcting any interference at his own expense.  
Guarantee and Compensation  
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On  
receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for  
material and manufacturing faults Barco must be informed immediately in writing of any complaints.  
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the  
date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco  
can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves  
to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the  
contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage  
attributed to the operation of software as well as to other services provided by Barco, being a component of the system  
or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of  
properties guaranteed in writing or due to the intent or gross negligence or part of Barco.  
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are  
handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the  
goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered  
invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic  
circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the  
guarantee provided by Barco either.  
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be  
complied with by the customer.  
Trademarks  
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their  
respective holders.  
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as  
advertising for the products or their manufacturers.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
TABLE OF CONTENTS  
1. SAFETY..................................................................................................................................................................................6  
1.1 General considerations....................................................................................................................................................6  
1.2 Important safety instructions............................................................................................................................................7  
2. INTRODUCTION...................................................................................................................................................................11  
2.1 Installation requirements................................................................................................................................................11  
2.2 Projector package overview...........................................................................................................................................12  
2.3 Product Overview ..........................................................................................................................................................13  
2.3.1 Main Unit .............................................................................................................................................................13  
2.3.2 Input/Output (I/O) Panel.......................................................................................................................................14  
2.3.3 Remote Control....................................................................................................................................................15  
3. INSTALLATION.....................................................................................................................................................................16  
3.1 RCU Battery Installation ................................................................................................................................................16  
3.2 Installing the Lens..........................................................................................................................................................17  
3.2.1 Lens Selection.....................................................................................................................................................17  
3.2.2 Installing the lens for the first time.......................................................................................................................17  
3.3 Connecting the Projector ...............................................................................................................................................18  
3.3.1 Connecting to a Computer or Laptop ..................................................................................................................18  
3.3.2 Connecting to Video Sources ..............................................................................................................................19  
3.3.3 Installing the cable cover .....................................................................................................................................20  
3.4 Powering On/Off the Projector.......................................................................................................................................21  
3.4.1 Powering On the Projector...................................................................................................................................21  
3.4.2 Powering Off the Projector ..................................................................................................................................21  
3.5 Adjusting the Projected Image.......................................................................................................................................22  
3.6 Safety Cover Installation................................................................................................................................................24  
3.7 Ceiling Mount Installation...............................................................................................................................................25  
4. USER CONTROLS ...............................................................................................................................................................26  
4.1 On-Screen Display Menus.............................................................................................................................................26  
4.1.1 Using the OSD Lite Menus..................................................................................................................................26  
4.1.2 Using the Advanced OSD Menus........................................................................................................................28  
4.1.2.1 Input Menu........................................................................................................................................................29  
4.1.2.2 Image Menu......................................................................................................................................................30  
4.1.2.3 Layout Menu.....................................................................................................................................................32  
4.1.2.4 Light Source Menu ...........................................................................................................................................33  
4.1.2.5 Alignment Menu................................................................................................................................................34  
4.1.2.6 Control Menu....................................................................................................................................................36  
4.1.2.7 Service Menu....................................................................................................................................................37  
4.2 Color Coordinate Adjustment.........................................................................................................................................38  
4.3 Constant Light Output....................................................................................................................................................40  
5. TROUBLESHOOTING ..........................................................................................................................................................41  
5.1 Image Problems.............................................................................................................................................................41  
5.2 LED Indication Chart .....................................................................................................................................................42  
5.3 Warning Message..........................................................................................................................................................43  
6. MAINTENANCE & SERVICE ...............................................................................................................................................44  
6.1 Replacing the Lens........................................................................................................................................................44  
7. SPECIFICATIONS ................................................................................................................................................................45  
7.1 PGWU-62L / PGWU-62L-K ...........................................................................................................................................45  
7.2 PGWX-62L / PGWX-62L-K............................................................................................................................................47  
7.3 Dimensions....................................................................................................................................................................49  
7.4 Compatibility Modes ......................................................................................................................................................50  
8. ENVIRONMENTAL INFORMATION .....................................................................................................................................52  
8.1 Disposal information......................................................................................................................................................52  
8.2 RoHS compliance..........................................................................................................................................................52  
8.3 Production address........................................................................................................................................................54  
8.4 Importers contact information........................................................................................................................................54  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Safety  
1. SAFETY  
About this chapter  
Read this chapter attentively. It contains important information to prevent personal injury while installing and using  
your PRESENT series projector. Furthermore, it includes several cautions to prevent damage to your PRESENT  
series projector. Ensure that you understand and follow all safety guidelines, safety instructions and warnings  
mentioned in this chapter before installing and using the PRESENT series projector. After this chapter, additional  
“warnings”and“cautions”are given depending on the procedure. Read and follow these“warnings”and“cautions”  
as well.  
Purpose of this device:  
The exclusive purpose of this device is to project images onto a screen in an indoor environment.  
Clarification of the term “PRESENT series” used in this document  
When referring in this document to the term“PRESENT series”means that the content is applicable for following  
Barco products:  
y
y
y
y
PGWX-62L  
PGWX-62L-K  
PGWU-62L  
PGWU-62L-K  
Note: This manual is applicable for multiple projector models. Consult the Barco website to know which models  
are currently for sale.  
Overview  
y
y
General considerations  
Important safety instructions  
1.1 General considerations  
y
y
y
The projector is a Class 2 laser device that conforms with IEC 60825-1:2007 and CFR 1040.10 and 1040.11  
Class 2 laser product. Do not stare into Beam.  
This projector has built-in Class 4 laser module. Disassembly or modification is very dangerous and should  
never be attempted.  
Any operation or adjustment not specifically instructed by the user’s guide creates the risk of hazardous laser  
radiation exposure.  
y
y
y
Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.  
Do not stare into beam when the projector is on.The bright light may result in permanent eye damage.  
Without following the control, adjustment or operation procedure may cause damage by the exposure of laser  
radiation.  
General safety instructions  
y
y
Before operating this equipment please read this manual thoroughly and retain it for future reference.  
Installation and preliminary adjustments should be performed by qualified Barco personnel or by authorized  
Barco service dealers.  
y
y
y
All warnings on the projector and in the documentation manuals should be adhered to.  
All instructions for operating and use of this equipment must be followed precisely.  
All local installation codes should be adhered to.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
1. Safety  
Do not look or stare into the projector’s lens when the laser projector is on.The bright  
light may hurt and damage you eyes.  
Notice on safety  
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1,  
EN60950-1, UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology  
equipment including electrical business equipment.  
These safety standards impose important requirements on the use of safety critical components, materials and  
insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having  
access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation  
levels, mechanical stability and strength, enclosure construction and protection against the risk of fire. Simulated  
single fault condition testing ensures the safety of the equipment to the user even when the equipment’s normal  
operation fails.  
Users definition  
Throughout this manual, the term SERVICE PERSONNEL refers to persons having appropriate technical training  
and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not  
limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in  
performing a task, and of measures to minimize the potential risk to themselves or other persons.The term USER  
and OPERATOR refers to any person other than SERVICE PER-SONNEL, AUTHORIZED to operate professional  
projection systems.  
A PRESENT series projector is intended“FOR PROFESSIONAL USE ONLY”by AUTHORIZED PERSONNEL  
familiar with potential hazards associated with high voltage, high intensity light beams, ultraviolet exposure and high  
temperatures generated by the laser diode and associated circuits.  
Owners record  
The part number and serial number are printed on a label which is stuck on the respective part. Record these  
numbers in the spaces provided below. Refer to them whenever you call upon your Barco dealer regarding this  
product.  
Product article number  
Product serial number  
Dealer  
1.2 Important safety instructions  
To prevent the risk of electrical shock  
y
y
This product should be operated from a mono phase AC power source.  
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the  
supplied power cables are the correct one, consult your dealer. If you are unable to insert the plug into the  
outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type  
plug.  
y
y
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.  
To disconnect the cord, pull it out by the plug. Never pull the cord itself.  
Use only the power cord supplied with your device. While appearing to be similar, other power cords have not  
been safety tested at the factory and may not be used to power the device. For a replacement power cord,  
contact your dealer.  
y
Do not operate the projector with a damaged cord. Replace the cord. Do not operate the projector if the projec-  
tor has been dropped or damaged until it has been examined and approved for operation by a qualified service  
technician.  
y
y
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.  
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be  
used. A cord rated for less amperage than the projector may overheat.  
y
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage  
points or short out parts that could result in a risk of fire or electrical shock.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
1. Safety  
y
y
y
y
Do not expose this projector to rain or moisture.  
Do not immerse or expose this projector in water or other liquids.  
Do not spill liquid of any kind on this projector.  
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service  
personnel before resuming operations.  
y
Do not disassemble this projector, always take it to an authorized trained service person when service or repair  
work is required.  
y
y
Do not use an accessory attachment which is not recommended by the manufacturer.  
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall outlet.This will prevent damage to the device due to  
lightning and AC power-line surges.  
To prevent personal injury  
y
To prevent injury and physical damage, always read this manual and all labels on the system before connecting  
to the wall outlet or adjusting the projector.  
y
y
y
To prevent injury, take note of the weight of the projector.  
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.  
Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the  
eye.  
y
y
y
y
Warning: extremely high brightness laser:This projector uses extremely high brightness laser. Never attempt to  
look directly into the lens or at the laser.  
Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from  
the wall outlet.  
When required to switch off the projector, to access parts inside, always disconnect the power cord from the  
power net.  
The power input at the projector side is considered as the disconnect device. When required to switch off the  
projector, to access parts inside, always disconnect the power cord at the projector side. In case the power input  
at the projector side is not accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be  
installed nearby the projector and be easily accessible, or a readily accessible general disconnect device shall  
be incorporated in the fixed wiring.  
y
y
Do not place this equipment on an unstable cart, stand, or table.The product may fall, causing serious damage  
to it and possible injury to the user.  
It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they  
have become visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or  
deep scratches.  
y
Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation.The  
American Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure  
for an-8 hour day to be less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation  
of the workplace is advised to assure employees are not exposed to cumulative radiation levels exceeding these  
government guidelines.The exposer of this UV radiation is allowed for only 1 hour per day for maintenance and  
service persons.  
To prevent fire hazard  
y
y
Do not place flammable or combustible materials near the projector!  
Barco large screen projection products are designed and manufactured to meet the most stringent safety  
regulations.This projector radiates heat on its external surfaces and from ventilation ducts during normal  
operation, which is both normal and safe. Exposing flammable or combustible materials into close proximity  
of this projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it  
is absolutely necessary to leave an“exclusion zone”around all external surfaces of the projector whereby no  
flammable or combustible materials are present.The exclusion zone must be not less than 50 cm (20”) for all  
DLP projectors.The exclusion zone on the lens side must be at least 5 m. Do not cover the projector or the lens  
with any material while the projector is in operation. Keep flammable and combustible materials away from the  
projector at all times. Mount the projector in a well-ventilated area away from sources of ignition and out of direct  
sun light. Never expose the projector to rain or moisture. In the event of fire, use sand, CO2 or dry powder  
fire extinguishers. Never use water on an electrical fire. Always have service performed on this projector by  
authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Safety  
replacement parts as they may degrade the safety of this projector.  
y
Slots and openings in this equipment are provided for ventilation.To ensure reliable operation of the projector  
and to protect it from overheating, these openings must not be blocked or covered.The openings should never  
be blocked by placing the projector too close to walls, or other similar surface.This projector should never be  
placed near or over a radiator or heat register.This projector should not be placed in a built-in installation or  
enclosure unless proper ventilation is provided.  
y
y
Projection rooms must be well ventilated or cooled in order to avoid build up of heat.  
Let the projector cool down completely before storing. Remove cord from the projector when storing.  
To prevent projector damage  
y
The air filters of the projector must be cleaned or replaced on regular base (a“clean”booth would be monthly-  
minimum). Neglecting this could result in disrupting the air flow inside the projector, causing overheating.  
Overheating may lead to the projector shutting down during operation.  
y
y
y
The projector must always be installed in a manner which ensures free flow of air into its air inlets and  
unimpeded evacuation of the hot air from its cooling system.  
In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic  
Compatibility (EMC) requirements, it should always be operated with all of its covers in place.  
Slots and openings in the cabinet are provided for ventilation.To ensure reliable operation of the product and  
to protect it from overheating, these openings must not be blocked or covered.The openings should never be  
blocked by placing the product on a bed, sofa, rug, or other similar surface.This product should never be placed  
near or over a radiator or heat register.The device should not be placed in a built-in installation or enclosure  
unless proper ventilation is provided.  
y
y
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug  
the mains supply immediately. Do not operate the projector again until it has been checked by qualified service  
personnel.  
Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects  
may not be nearer to the projector than 30 cm (12”) on any side.  
y
y
Do not use this equipment near water.  
Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as  
high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the  
Digital Mirror Devices™ in which case there is a loss of warranty.  
y
y
y
Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror  
Devices™ in which case there is a loss of warranty.  
Save the original shipping carton and packing material.They will come in handy if you ever have to ship your  
equipment. For maximum protection, repack your set as it was originally packed at the factory.  
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use  
a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since  
these will damage the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild  
detergent solution.  
y
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an  
anti-reflective coating, therefore, avoid touching the lens.To remove dust on the lens, use a soft dry cloth. Do  
not use a damp cloth, detergent solution, or thinner.  
y
y
Rated maximum ambient temperature, ta= 40 °C (104 °F).  
This projector can be set to any angle within vertical 360° range. It can also rotate 90° into portrait orientation.  
360°  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Safety  
y
Allowing the proper space of the projector cabinet is critical for proper air circulation and cooling of the unit.The  
dimensions shown here indicate the minimum space required. If the projector is to be built into a compartment  
or similarly enclosed, these minimum distances must be maintained.  
4” (10 cm)  
20” (50 cm)  
20” (50 cm)  
On servicing  
y
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous  
voltage potentials and risk of electric shock.  
y
y
Refer all servicing to qualified service personnel.  
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in  
this manual can lead to permanent damage to the projector and cancellation of the warranty.  
y
Unplug this product from the wall outlet and refer servicing to qualified service technicians under the following  
conditions:  
-
-
-
-
When the power cord or plug is damaged or frayed.  
If liquid has been spilled into the equipment.  
If the product has been exposed to rain or water.  
If the product does not operate normally when the operating instructions are followed. Adjust only those  
controls that are covered by the operating instructions since improper adjustment of the other controls may  
result in damage and will often require extensive work by a qualified technician to restore the product to  
normal operation.  
-
-
If the product has been dropped or the cabinet has been damaged.  
If the product exhibits a distinct change in performance, indicating a need for service.  
y
y
Replacement parts: When replacement parts are required, be sure the service technician has used original  
Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco  
original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock  
or other hazards. Unauthorized substitutions may void warranty.  
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform  
safety checks to determine that the product is in proper operating condition.  
To prevent battery explosion  
y
y
y
Danger of explosion if battery is incorrectly installed.  
Replace only with the same or equivalent type recommended by the manufacturer. (AAA LR03,1.5V)  
For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules  
and regulations to ensure proper disposal.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Introduction  
2. INTRODUCTION  
About this chapter  
Read this chapter before installing PRESENT series projector. It contains important information concerning  
installation requirements for the PRESENT series projector, such as minimum and maximum allowed ambient  
temperature, humidity conditions, required safety area around the installed projector, required power net, etc.  
Furthermore, careful consideration of things such as image size, ambient light level, projector placement and type  
of screen to use are critical to the optimum use of the projection system.  
Overview  
y
y
Installation requirements  
Projector package overview  
Note: Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms  
of guarantee. Observing the specification mentioned in this chapter is critical for projector performance.  
Neglecting this can result in loss of warranty.  
2.1 Installation requirements  
Environment conditions  
Table below summarizes the physical environment in which the PGWX-62L/PGWU-62L/PGWX-62L-K/  
PGWU-62L-K projector may be safely operated or stored.  
Environment  
Operating  
Non-Operating  
Ambient Temperature  
Humidity  
5 °C (41 °F) to 40 °C (104 °F)  
10% to 85% RH Non-Condensed  
0 (0Ft) to 3000m (9843Ft)  
-10°C (14°F) to 60°C (140°F)  
5% to 90% RH Non-Condensed  
Altitude  
Cooling requirements  
The projector is fan cooled and must be installed with sufficient space around the projector head, minimum 30 cm  
(12 inch) to ensure sufficient air flow. It should be used in an area where the ambient temperature, as measured at  
the projector air inlet , does not exceed +40°C (+104°F).  
Clean air environment  
A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors  
ventilation inlets. For installations in environments where the projector is subject to airborne contaminants such  
as that produced by smoke machines or similar (these deposit a thin layer of greasy residue upon the projectors  
internal optics and imaging electronic surfaces, degrading performance), then it is highly advisable and desirable to  
have this contamination removed prior to it reaching the projectors clean air supply. Devices or structures to extract  
or shield contaminated air well away from the projector are a prerequisite, if this is not a feasible solution then  
measures to relocate the projector to a clean air environment should be considered.  
Only ever use the manufacturer’s recommended cleaning kit which has been specifically designed for cleaning  
optical parts, never use industrial strength cleaners on the projector’s optics as these will degrade optical coatings  
and damage sensitive optoelectronics components. Failure to take suitable precautions to protect the projector  
from the effects of persistent and prolonged air contaminants will culminate in extensive and irreversible ingrained  
optical damage. At this stage cleaning of the internal optical units will be noneffective and impracticable. Damage of  
this nature is under no circumstances covered under the manufacturer’s warranty and may deem the warranty null  
and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the  
clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne  
particles in the environment of the projector.The manufacturer reserves the right to refuse repair if a projector has  
been subject to knowingly neglect, abandon or improper use.  
Main Power requirements  
The PRESENT series projector operates from a nominal mono phase power net with a separate earth ground PE.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2. Introduction  
Projector  
Power requirements  
PGWX-62L/PGWX-62L-K  
PGWU-62L/PGWU-62L-K  
AC INPUT 100-240V, 6.5A, 50/60Hz  
AC INPUT 100-240V, 6.5A, 50/60Hz  
The power cord required to connect the projector with the power net is delivered with the projector.  
Projector weight  
Do not underestimate the weight of the projector.The projector weights about 17.5 kg without lens. Be sure that the  
pedestal or ceiling mount on which the projector has to be installed is capable of handling five (5) times the com-  
plete load of the system.  
2.2 Projector package overview  
Box content  
This projector comes with all the items shown below. Check to make sure your package is complete. Contact your  
dealer immediately if anything is missing.  
Remote Control with two AAA size  
batteries  
User Guide, Quick Start  
Guide, Safety Manual  
Projector  
Lens Cover  
Cable Cover  
Power Cord (US)  
Power Cord (China)  
Power Cord (EU)  
5V Connection Cable  
Note: 5V connection cable is for use with optional modules.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2. Introduction  
2.3 Product Overview  
2.3.1 Main Unit  
Component Location  
2
1
Menu  
HDMI  
Enter  
VGA-OUT  
VGA-IN  
DVI  
3
4
LAN  
RS-232  
12V  
OUT  
5V  
OUT  
CVBS  
5
6
7
1
Projection Lens Cap  
2
Ventilation Holes  
3
Control Panel  
4
Input/Output (I/O) Panel  
5
Power Switch  
6
Power Socket (AC Input:AC100-240V~, 50-60Hz)  
Tilt-Adjustment Feet  
7
Note: The Projection Lens is optional item not a standard accessary in the package.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2. Introduction  
2.3.2 Input/Output (I/O) Panel  
Component Location  
1
2
3
4
HDMI  
VGA-OUT  
VGA-IN  
DVI  
LAN  
RS-232  
12V  
OUT  
5V  
OUT  
CVBS  
9
8
7
6
5
1
2
3
4
5
6
7
8
9
Monitor Connector (Loop from VGA)  
VGA Connector (PC Analog Signal/Component Video Input)  
HDMI Connector  
DVI-D Input Connector  
Video Input Connector  
+5V Relay Connector  
+12V Relay Connector  
RS232 Connector  
Networking Connector RJ45  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2. Introduction  
2.3.3 Remote Control  
Button Location  
10  
8
1
On/Off  
1
2
Home  
3
OK  
5
6
7
4
Arrow Right  
4
5
Arrow Up  
3
2
6
Arrow Left  
7
Arrow Down  
8
LED Indication  
Battery  
Compartment  
9
IR LED’S  
10  
9
Use the remote control to control these functions.  
Basic Remote Command (Result)  
Start the projector  
Remote Lite (Action)  
Press“On/off”  
Press“On/off”  
Turn off the projector  
1
2
1
>
Show main menu on screen  
Press“Home”  
5
7
Move through menu  
Press“Arrow keys”  
6
4
Select button  
Press“OK”  
3
3
2
2
Select and return to previous menu  
Return to previous menu without selecting  
Clear the menu from the screen  
Activate picture mute function  
Activate picture freeze function  
Press“OK”  
Press“Home”  
Press“Home”  
press 2x“Arrow Up”  
press 2x“Arrow Left”  
Press any key to deactivate.  
Press 2x“Arrow Left”again to  
deactivate.  
Note: The picture freeze function is not workable when PIP is activated.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Installation  
3. INSTALLATION  
Overview  
y
y
y
y
y
y
y
RCU Battery Installation  
Installing the Lens  
Connecting the Projector  
Powering On/Off the Projector  
Adjusting the Projected Image  
Safety Cover Instalation  
Ceiling Mount Installation  
3.1 RCU Battery Installation  
Procedure:  
1. Remove the cover by sliding it in the direction indicated by the arrow.  
1
2
2. Insert two new AAA batteries (observe the polarity).  
3
3. Replace the cover.  
2
3
1
Notes for the Remote Control Unit  
y
y
Be sure to insert the batteries in the corresponding orientations to match the polarities.  
Do not mix new batteries with used batteries as it would shorten the life of new batteries or cause  
leakage.  
y
y
y
y
Only used AAA batteries as instructed; do not attempt to insert different types of batteries into the  
remote control.  
If the remote is going to be unused for long periods of time, be sure to remove the batteries to prevent  
leakage, which could damage the remote control.  
The liquid contents in the batteries is harmful to the skin; do not touch the leakage with your bare  
hands directly. When installing fresh batteries, be sure to clean up the leakage thoroughly.  
Under most circumstances, you only need to point the remote control towards the screen and the  
IR signal would be reflected off the screen and picked up by the IR sensor on the projector. But  
under specific circumstances, the projector may fail to receive signals from the remote control due to  
environmental factors. When this happens, orient the remote control at the projector and try again.  
y
y
y
If the range of effective remote control signal reception decreases or if the remote control stops  
working, replace the batteries.  
If the infrared receiver is exposed to fluorescent lamp or strong sunlight, the remote control may not  
operate normally.  
Refer to the regulations enforced by your local government on the disposal of used batteries; improper  
disposal could damage the environment.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Installation  
3.2 Installing the Lens  
3.2.1 Lens Selection  
Procedure:  
1. Determine the required screen width (SW).  
2. Determine the approximate position of the projector in the room.  
3. Start up the Lens Calculator on the Barco website: http://www.barco.com/en/tools/lenscalculator to determine  
the possible lenses for your configuration. As a result the Lens Calculator window opens.  
Notes:  
y
The Lens Calculator can also be used to determine the position of the projector when the lens type and  
screen width is known.  
y
Due to lens tolerances the results of calculated values may be different from measured values.These  
difference may vary +/- 5%.  
3.2.2 Installing the lens for the first time  
Warning: This procedure may only be performed by qualified technical service personnel.  
Procedure:  
1
1. Lens cap should be removed before installing the lens. If not it will damage the projector.  
2
2. Remove the lens cap counterclockwise.  
3
3. Rotate the bar upwards to release the lock.  
4
4. Be sure the label“TOP”of lens is upward and then push the lens into the position.  
5
5. Rotate the lens clockwise to lock the lens and then rotate the bar downwards.  
6
6. Put the lens cover on the lens with the sound“click”.  
2
3
1
4
5
6
Caution: Do not transport the projector with any lens installed.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Installation  
Lens Specification  
Projection Lens P/N  
R9832755  
R9832753  
R9832754  
R9832756  
Long Zoom  
R9832778  
Standard  
WXGA/  
WUXGA  
Standard  
WUXGA  
Ultra Long  
Zoom  
Lens Type  
Wide Zoom  
Throw Ratio (WXGA)  
Throw Ratio (WUXGA)  
Zoom Ratio  
1.00-1.28  
0.95-1.22  
1.28X  
1.28-1.61  
1.22-1.53  
1.25X  
---  
1.60-3.07  
1.52-2.92  
1.9X  
3.04-5.78  
2.90-5.50  
1.9X  
1.22-1.53  
1.25X  
3.3 Connecting the Projector  
3.3.1 Connecting to a Computer or Laptop  
Wiring Diagram  
7
+12V Relay Output  
3
4
5
6
Menu  
HDMI  
Enter  
VGA-OUT  
VGA-IN  
DVI  
LAN  
RS-232  
12V  
OUT  
5V  
OUT  
CVBS  
2
Network Port  
1
1
2
3
4
5
6
7
Network Cable  
Power Cord  
HDMI Cable  
VGA in Cable  
VGA out Cable  
12V DC Jack  
RS232 Cable  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Installation  
3.3.2 Connecting to Video Sources  
Wiring Diagram  
DVD Player, Set-top Box,  
HDTV Receiver  
Video Output  
4
5
3
Menu  
HDMI  
Enter  
VGA-OUT  
VGA-IN  
DVI  
LAN  
RS-232  
12V  
OUT  
5V  
OUT  
CVBS  
2
+12V Relay Output  
1
1
2
3
4
5
12V DC Jack  
Power Cord  
DVI-D Cable  
HDMI Cable  
Composite Video Cable  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Installation  
3.3.3 Installing the cable cover  
Procedure  
1. Pull the cable cover upwards to engage the cable cover with the projector.  
2. Gently flip the projector over so that its top panel is facing up.  
3. Rotate the screws securing the cable cover.  
Note: To remove the cable cover, reverse the previous step.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Installation  
3.4 Powering On/Off the Projector  
3.4.1 Powering On the Projector  
Procedure:  
1
1. Ensure that the power cord and signal cable are securely connected. Power on the switch  
Status LED is solid red.  
and wait until the  
2
2. Turn on the projector by pressing“ ”on the remote control or the control panel.The Status LED is off.  
The startup screen displays in approximately 10 seconds.  
3. Turn on your source. Select an input source by the remote control (HDMI,VGA, DVI or Video).  
The projector detects the source you selected and displays the image.  
2
Power button  
VGA-OU  
or  
Status LED  
5V  
OUT  
CVBS  
1
Power Switch  
IR Receiver  
3.4.2 Powering Off the Projector  
Procedure:  
1. Press“ ”key of on the remote control or the control panel, a message displays on the projector’s screen.  
2. Press“ ”key again to confirm, otherwise the message disappears after 5 seconds.  
CAUTION: Don’t turn on the projector immediately after entering Standby mode.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Installation  
3.5 Adjusting the Projected Image  
Adjusting the Projector’s Position  
To determine where to position the projector, consider the size and shape of your screen, the location of your power  
outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines:  
-
-
Position the projector on a flat surface at a right angle to the screen.  
Position the projector to the desired distance from the screen.  
The distance from the lens of the projector to the screen, the zoom setting, and the video format determine  
the size of the projected image.  
-
The image offset (shift) range for the projector please refer below:  
Model  
H
V
PGWX-62L/PGWX-62L-K  
PGWU-62L/PGWU-62L-K  
30%  
30%  
100%  
100%  
H: the horizontal image offset range when lens is centered.  
V: the vertical image offset range when lens is centered.  
H
H
V
V
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Installation  
Vertical Image Offset: +/-100%  
+100%  
100%  
100%  
Lens Center  
-100%  
Horizontal Image Offset: +/-30%  
Lens Center  
-30%  
100%  
100%  
+30%  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. User Controls  
3.6 Safety Cover Installation  
By installing a safety cover (optional part), the projector can be mounted vertically to display images in portrait  
orientation.  
Procedure:  
1. Align and hook the safety cover to the side of the projector, as shown in the illustration below.  
2. Push the safety cover upwards until it locks into place.  
3. Gently flip the projector over so that its bottom panel is facing up.  
4. Fix the screws to secure the safety cover to the projector.  
Notes:  
y
When the projector is in protrait orientation.The OSD will not be able to rotate accordingly and the lens  
shift will be same as table/ceiling installation direction.  
y
To remove the safety cover, reverse the previous step.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Installation  
3.7 Ceiling Mount Installation  
Requirements:  
Ensure the screws used to attach a mount to the projector meet the following specifications:  
-
-
Screw type: M6*10  
Mounting dimension  
400  
200  
405  
Mounting Holes  
200  
Note: Damage resulting from incorrect installation will void the warranty.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
4. USER CONTROLS  
Overview  
y
On-Screen Display Menus  
4.1 On-Screen Display Menus  
The projector has On-Screen Display (OSD) menus that allow you to make image adjustments and  
change a variety of settings.  
4.1.1 Using the OSD Lite Menus  
Main Menu & Buttons  
5
INPUT  
BRIGHTNESS  
CONTRAST  
LENS ZOOM  
INFO  
COLOR  
LENS SHIFT  
MODE  
Main Menu  
3
7
6
4
ASPECT RATIO LENS FOCUS  
KEYSTONE  
SERVICE  
LANGUAGE  
ADVANCED  
2
Functionality  
Basic OSD Lite navigation  
(Result)  
Remote Lite  
(Action)  
OSD Lite  
(On Screen)  
Show main menu of OSD Lite on  
screen  
main menu appears in bottom  
right corner  
Press“Home”  
2
5
7
button will turn red when the  
function is available  
6
4
To move through the OSD Lite  
Go to desired function  
Press“Arrow keys”  
the menu of the desired  
function will appear  
Press“OK”  
3
2
the main menu will be displayed  
or when you are in the main  
menu the screen will be cleared  
Leave the menu or clear the  
screen  
Press“Home”  
Hotkey / Short Cut  
Remote Lite -> OSD Lite  
(Action -> On Screen)  
Remote Command (Result)  
5
5
use arrow keys to focus lens  
6
4
6
4
3
3
To quickly adjust a blurry screen  
3
use arrow keys to move lens  
>
>
7
7
use arrow keys to zoom lens  
To mute picture on the projector  
Unmute picture on the projector  
To freeze picture on the projector  
Unfreeze picture on the projector  
5
5
>
Press any key  
6
6
6
6
>
>
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
Remote Lite -> OSD Lite  
Main menu is on screen, go to button  
required (Result)  
(Action -> On Screen)  
5
go to input desired (default  
setting = AutoSelect)  
6
4
Select input manually  
3
3
3
>
>
7
6
4
Make the image  
brighter or darker  
3
3
>
>
default setting= middle  
Adapt the contrast  
between light/dark  
areas  
6
4
3
3
default setting= middle  
best condition to view  
“computer”images (=default  
image)  
3
Select color preset  
most fitted for your  
image  
best option to view movies  
100% bright  
3
3
3
3
3
provides the simulated  
DICOM  
3
3
5
7
go to aspect ratio desired  
(default setting = NATIVE)  
6
4
Adjust aspect ratio  
3
>
>
Adjust focus of image  
6
4
3
3
3
3
>
>
use arrow keys to focus lens  
use arrow keys to zoom lens  
5
6
4
5
7
Adjust size of image  
7
5
7
Adjust position of  
image  
6
4
3
3
>
use arrow keys to move lens  
5
7
use arrow keys to do  
vertical keystone  
3
3
3
3
>
>
Adjust keystone  
use arrow keys to do  
vertical keystone  
6
4
5
4
7
go to language desired  
(default setting = ENGLISH)  
6
Select language  
3
3
>
>
>
Show light source  
info  
3
3
3
3
3
3
>
>
>
go to light source mode  
desired (default setting =  
NORMAL)  
Select light source  
mode  
6
4
Show projector info  
Enter advanced  
menu  
3
Enter advanced menu  
3
>
>
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. User Controls  
4.1.2 Using the Advanced OSD Menus  
Procedure:  
1. Select the Advanced button in OSD Lite Menus to enter advanced menu.  
2. When the advanced OSD displays, use the arrow keys to navigate in the menu and enter to a  
desired item.  
3. Use the UP/DOWN buttons to select the desired item in the submenu and adjust the settings with the  
LEFT/RIGHT buttons or press ENTER to go to another submenu.  
4. Select the next item that you want to adjust in the submenu and adjust it as described above. When  
each item is adjusted, the projector saves the new setting.  
5. Press HOME to return to the previous menu.  
6. To exit the OSD menu, press HOME again.  
INPUT  
BRIGHTNESS  
CONTRAST  
LENS ZOOM  
INFO  
COLOR  
LENS SHIFT  
MODE  
Advanced OSD Menu  
ASPECT RATIO LENS FOCUS  
KEYSTONE  
SERVICE  
LANGUAGE  
ADVANCED  
Submenu  
Setting  
Another Submenu  
Input Select  
HDMI  
Advanced OSD  
Input  
Input Select  
Auto Power Off  
Auto Power On  
No Signal  
Enter  
On  
Input  
Image  
VGA  
DVI  
Off  
Layout  
Logo  
Always  
Off  
Light source  
CVBS  
A Image Adjust  
3D Mode  
Alignment  
Control  
Service  
3D Invert  
Off  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
4.1.2.1 Input Menu  
Input  
Input Select  
Auto Power Off  
Auto Power On  
No Signal  
Enter  
On  
Input  
Off  
Input Select  
Auto Power Off  
Auto Power On  
No Signal  
Enter  
On  
Logo  
Always  
Off  
A Image Adjust  
3D Mode  
Off  
Logo  
Always  
3D Invert  
Off  
A Image Adjust  
PGWX-62L / PGWX-62L-K  
PGWU-62L / PGWU-62L-K  
Input Select  
Select the active source, include the following options:  
y
y
HDMI  
VGA  
y
y
DVI  
CVBS  
Auto Power Off  
Switch off after a while when no sync detected.  
y
y
Off: Default value. Disable auto power off function.  
On: Projector will switch off automatically when no signal for 20 minutes.  
Auto Power On  
The projector turns on automatically when switch on projector after connecting power.  
y
y
Off: Default value.The projector stays off when AC power is applied.The user must power on the projector.  
On:The projector turns on automatically when switch on projector after connecting power.  
No Signal  
Select what image displayed when no signal.  
y
y
y
y
Logo: Default value. Search screen is the factory logo picture.  
Blue: Search screen is solid blue (RGB=0,0,255).  
Black: Search screen is solid black (RGB=0,0,0).  
White: Search screen is solid white (RGB=255,255,255).  
A Image Adjust  
Select the mode of the auto image menu.  
y
Always: Default value. Always execute the function of image\Auto image even if the timing is the same as  
previous source.  
y
y
Off: Never execute the function of image\Auto image.  
Auto: Execute the function of image\Auto image when you get a different timing then previous source.  
3D Mode  
Select the 3D mode  
y
y
Off: Default value.  
On: Set“On”to turn 3D settings on for 3D images. Compatible 3D source, 3D content and active shutter  
glasses are required for 3D viewing.  
3D Invert (off & on)  
y
y
Off: Default value.  
On: Set 3D invert“On”to invert left and right frame contents.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
4.1.2.2 Image Menu  
IMAGE  
Brightness  
Contrast  
Saturation  
Tint  
Sharpness  
Noise Reduction  
Color Temp  
Native  
Input Balance  
Aspect Ratio  
Timings  
Enter  
Auto  
Enter  
Auto Image  
Execute  
Presentation  
Display Mode  
Brightness  
Adjust the brightness of the image.  
y
y
Press the ◄ to darken image.  
Press the ► to lighten the image.  
Contrast  
Adjust the contrast of the image.  
y
y
Press the ◄ to decrease the contrast.  
Press the ► to increase the contrast.  
Saturation  
Adjust the color saturation of the image.  
y
y
Press the ◄ to decrease the amount of saturation in the image.  
Press the ► to increase the amount of saturation in the image.  
Tint  
Adjust the tint (color balance between red and green) of the image.  
y
y
Press the ◄ to increase the amount of green in the image.  
Press the ► to increase the amount of red in the image.  
Sharpness  
Adjust the sharpness of the image.  
y
y
Press the ◄ to decrease the sharpness.  
Press the ► to increase the sharpness.  
Noise Reduction  
Reduce temporary and/or spatial noise in the image.  
y
y
Press the ◄ to decrease the noise.  
Press the ► to increase the noise.  
Note: Saturation, Tint and Noise reduction function supported source: CVBS.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
Color Temp  
Adjust the color temperature of the image.  
y
y
y
y
Cool:Apply“Cool” color temperature setting.  
Bright:Apply“Bright”color temperature setting.  
Warm:Apply“Warm”color temperature setting.  
Warmest:Apply“Warmest”color temperature setting.  
Input Balance  
Adjust the gain and offset of the red, green, or blue channel of the image.This is similar to adjusting contrast, but  
only affects a single color channel.  
y
y
y
y
Offset: Refer to the control of color imbalance in the darker areas of the projected image.  
Gain: Refer to the control of color imbalance in the brighter areas of the projected image.  
Press the ◄ to decrease the input balance.  
Press the ► to increase the input balance.  
Aspect Ratio  
Adjust the aspect ratio of the image.  
y
y
y
4:3:The input image is resized to a 4:3 aspect ratio.  
16:10:The input image is resized to a 16:10 aspect ratio.  
Native: the original aspect ratio of the source is kept and fit to screen.This is height or width whatever comes  
first.  
y
Auto:Automatically selects the appropriate display format.  
Timings  
Adjust the horizontal position, phase or vertical position of the image.  
Note: Timings function supported sources: analog computer, analog component.  
y
y
Press the ◄ to decrease the horizontal position, phase or vertical position.  
Press the ► to increase the horizontal position, phase or vertical position.  
Auto Image  
Execute the auto image adjust.  
y
y
Press EXECUTE to adjust the image size, phase and timing automatically.  
Force the projector to reacquire and lock to the input signal.This is useful when signal quality is marginal. After  
executing this command, the projector will enter the search status. After the signal is reacquired, the image  
settings (H start, H phase,V start) will be optimized for the input signal.  
Display Mode  
Change the sequence and waveform of the image.  
y
y
y
y
Bright: Default value.This preset provides maximum lumens output.  
Presentation:This preset provides the best possible image for presentation and computer graphics.  
Video:This preset provides the best possible image for video sources (DVD,TV, etc.)  
DICOM:This preset provides the simulated DICOM.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. User Controls  
4.1.2.3 Layout Menu  
LAYOUT  
Main size  
Main select  
PIP select  
Enter  
Enter  
Top Left  
Medium  
Off  
PIP position  
PIP size  
PIP  
Main size  
Set the size of the main window.  
This function is zoom out/cropping image, the location of image will be kept in center.  
y
y
Press the ◄ to decrease the main size.  
Press the ► to increase the main size.  
Note: Please be noticed that for the PGWU-62L/PGWU-62L-K model. When the main size setting is ≥ 3 at composite  
input, the ripple picture symptom can be found.  
Main select  
Select the source for the main window.  
y
y
HDMI  
VGA  
y
y
DVI  
Video  
PIP select  
Select the source for the PIP window.This function is grey when PIP is Off.  
y
y
HDMI  
VGA  
y
y
DVI  
Video  
PIP position  
Set the position of the PIP window.  
y
y
y
y
Top Right: Default value for this function.  
Top Left  
Bottom Left  
Bottom Right  
PIP size  
Set the size of the PIP window.  
The PIP size can be different for different input resolutions.  
y
y
y
Small: PIP window is about 1/9 width of the entire display.  
Medium: PIP window is about 1/8 width of the entire display.  
Large: PIP window is about 1/7 width of the entire display.  
PIP  
Activate the PIP window.  
Note: The ripple picture symptom (a bit vibrated behavior) occurred at main picture under 480i, 576i & 1080i while PIP  
mode activate, is a bandwidth limitation.  
y
y
Off: Default value.The PIP function is disabled and only main window is visible.  
On:The PIP image is on top of the main image.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
4.1.2.4 Light Source Menu  
Light source  
Mode  
Normal  
Off  
High Altitude  
Power  
Constant  
Enable  
Color Calibration  
Execute  
Mode  
Set light source mode of the projector.  
y
y
y
Normal: Default value. When set to normal mode, the wattage of the laser diode will be at full power.  
Eco: When set to eco mode, the wattage of the laser diode will be at eco power.  
Power: Enable laser power adjust.  
High Altitude  
When“On”is selected, the fans will spin faster.This feature is useful in high altitude areas where the air is thin.  
y
y
Off: Default value.  
On: Set high altitude mode on.  
Power  
Set laser power level of the projector.  
Note: Power function will not be available if you have set the laser to Eco or Normal modes.  
y
y
Press the ◄ to decrease the power level.  
Press the ► to increase the power level.  
Constant  
When“Enable”is selected, the light level will apply more power to maintain the constant brightness.  
y
Enable:The light level will apply more power to maintain the constant brightness as the laser brightness decays  
naturally over time.  
y
Disable: Default value.  
Color Calibration  
Calibrate light sensor for Constant mode to work properly. It will take 3 minutes to complete the color calibration.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
4.1.2.5 Alignment Menu  
ALIGNMENT  
Rear projection  
Ceiling mode  
Lens control  
Off  
Off  
Enter  
Keystone  
Gamma  
Film  
Enter  
Internal pattern  
Custom color space  
Lens to midposition  
Enter  
Execute  
Rear projection  
Reverse the image horizontally when the setup is with the projector at the rear of the screen.  
y
y
Off: Default value. Projector is in front projection mode.  
On: Projector is in rear projection mode.  
Ceiling mode  
Reverse the image vertically when the setup is with the projector which is mounted with a ceiling mount.  
y
y
Off: Default value. Projector is in the table mode.  
On: Projector is in ceiling mode.  
Lens control  
y
y
y
y
y
y
Zoom: Lens zoom.  
Focus: Lens focus.  
Enter to shift: Each time enter is pressed it will go from zoom/focus to shift to zoom/focus.  
Left/Right: Lens shift left/right.  
UP/Down: Lens shift up/down.  
Enter to zoom/focus: Each time enter is pressed it will go from zoom/focus to shift to zoom/focus.  
Keystone  
Adjust vertical keystone.  
Gamma  
Set gamma type.  
y
y
y
y
Film: for home theater.  
Video: for video or TV source.  
Graphics: for image source.  
Standard: for PC or computer source.  
Internal pattern  
The projector comes with some standard built-in patterns for testers to calibrate the equipment.  
y
None  
y
White  
y
Grid  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
Custom color space  
Adjust the .x and .y values of the primary colors and white.  
Custom color space  
Enable  
Auto Test Pattern  
On  
On  
Red Weighting of Red  
Green Weighting of Red  
Blue Weighting of Red  
Green Weighting of Green  
Red Weighting of Green  
Blue Weighting of Green  
Blue Weighting of Blue  
Red Weighting of Blue  
Green Weighting of Blue  
Red Weighting of White  
Green Weighting of White  
Blue Weighting of White  
Reset to default  
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
Enable: Set to On to enable CCN.The default value is Off.  
Auto Test Pattern: Set to Off to disable the Auto Test Pattern function.The default value is On.  
Red Weighting of Red: Press the ◄/► to decrease/increase the custom color space.  
Green Weighting of Red: Press the ◄/► to decrease/increase the custom color space.  
Blue Weighting of Red: Press the ◄/► to decrease/increase the custom color space.  
Green Weighting of Green: Press the ◄/► to decrease/increase the custom color space.  
Red Weighting of Green: Press the ◄/► to decrease/increase the custom color space.  
Blue Weighting of Green: Press the ◄/► to decrease/increase the custom color space.  
Blue Weighting of Blue: Press the ◄/► to decrease/increase the custom color space.  
Red Weighting of Blue: Press the ◄/► to decrease/increase the custom color space.  
Green Weighting of Blue: Press the ◄/► to decrease/increase the custom color space.  
Red Weighting of White: Press the ◄/► to decrease/increase the custom color space.  
Green Weighting of White: Press the ◄/► to decrease/increase the custom color space.  
Blue Weighting of White: Press the ◄/► to decrease/increase the custom color space.  
Reset to default: Resets all color points to default value.  
Lens to midposition  
Set the lens in the center/on axis position.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. User Controls  
4.1.2.6 Control Menu  
CONTROL  
Standby 5V  
Eco network power  
RS232 baudrate  
Network  
Off  
On  
Enter  
Top Left  
Off  
Menu position  
Auto source  
Language  
Enter  
Standby 5V  
Switch on/off for the 5V output in standby.  
y
y
Off: Default value. 5V output off in standby.  
On: 5V output on in standby.  
Eco network power  
Switch on/off the network power to save power.  
y
y
Off: Default value. Network is enable in standby and the power consumption is under 3W.  
On: Network is not available in standby and the power consumption is under 0.5W.  
RS232 baudrate  
Select RS232 baudrate.  
y
y
115200: Default value for this function.  
9600/19200: Other options.  
Network  
View the relevant network information.  
y
y
y
y
y
IP Address: Default value is 192.168.0.100.  
Subnet Mask: Default value is 255.255.255.0.  
Gateway  
DHCP: Default value is Off, key in the IP address manually and press APPLY.  
Apply:  
-
The DHCP function must be set to“On”and press“Apply”to get the IP address from DHCP server  
automatically.  
-
-
It takes several seconds to get the IP.  
In case of fail to get the IP address, please re-apply again.  
Menu position  
Shift the menu box to a position.  
y
y
y
y
y
Center: Default value for this function.  
Top Left  
Top Right  
Bottom Left  
Bottom Right  
Auto source  
Automatic source searching.  
y
y
On: Default value. Automatic source searching is enabled.  
Off:Automatic source searching is disabled.  
Language  
Select the language to display the OSD Menu.  
y
y
y
English  
German  
French  
y
y
y
Spanish  
y
y
y
Russian  
Korean  
Turkey  
Simplified Chinese  
Japanese  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
4.1.2.7 Service Menu  
SERVICE  
Model  
Serial no  
Soft version  
Main/PIP source  
Active resolution  
Pixel clock  
Vert. refresh  
Hor. refresh  
Sync type  
Color space  
Projector runtime  
Factory Reset  
Execute  
Model  
The designated model number of the projector.  
Serial no  
The designated serial number of the projector.  
Soft version  
The version of software installed on the projector.  
Main/PIP source  
Display the current main and PIP sources.  
Active resolution  
Display the current resolution of the current source.  
Pixel clock  
Display the pixel clock of the current input signal.  
Vert. refresh  
Display the current vertical refresh rate of the current source.  
Hor. refresh  
Display the current horizontal refresh rate of the current source.  
Sync type  
Value is one of the following:  
y
y
y
Separate: Signal has separate H&V syncs.  
Sync on Green: Sync on green channel.  
Composite: Sync embedded in video signal.  
Color space  
Display current color space.  
Projector runtime  
Display the projector’s total operating hours.  
Factory Reset  
Set all persistent settings back to default values.  
This function will not apply to items including No Signal, Network, Language, and Projector Hours.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
4.2 Color Coordinate Adjustment  
Note: If two or above projectors are used for blending, and there is color difference between the projectors,  
please adjust the color coordinate.  
Placement:  
Place the lux meters at the marked position“ “.  
Procedure:  
ALIGNMENT  
1. Press“Menu”->“Advanced”->“Alignment”->“Custom  
color space.  
Rear projection  
Off  
Off  
Ceiling mode  
Lens control  
Enter  
Keystone  
Gamma  
Film  
Enter  
Internal pattern  
Custom color space  
Lens to midposition  
Enter  
Execute  
Custom color space  
2. Select“Red Weighting of Red”to show a Red pattern.  
3. Assume lux of two screens are:  
Enable  
On  
On  
Left: 1800 lux  
Auto Test Pattern  
Right: 1500 lux  
Red Weighting of Red  
Green Weighting of Red  
Blue Weighting of Red  
Green Weighting of Green  
Red Weighting of Green  
4. Reduce the OSD value of the left projector to have the  
lux close to the right one, ex. 83.  
Blue Weighting of Green  
Blue Weighting of Blue  
Red Weighting of Blue  
Green Weighting of Blue  
Red Weighting of White  
Green Weighting of White  
Blue Weighting of White  
Reset to default  
Note: Turn on “Auto Test Pattern”, the item will show the internal R/G/B pattern automatically.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. User Controls  
5. Follow from step (2.) to (4.) to adjust“Green Weighting of Green”and“Blue Weighting of Blue”to have green/  
blue pattern with closed values.  
6. Then the color performance of left/right screens is closed to each other.  
7. If you would like to enchance color X with a little color Y, you can increase“Y weighting of X”.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. User Controls  
4.3 Constant Light Output  
Note: If the user hopes to maintain the constant light output, please enable the “Constant” function.  
Procedure:  
IMAGE  
1. Press“Menu”->“Advanced”->“Image”->“Display mode”,  
then choose one display mode:“Presentation”or”Video”  
or“Bright”or“DICOM SIM”.  
Brightness  
Contrast  
Saturation  
Tint  
Sharpness  
Noise Reduction  
Color Temp  
Native  
Input Balance  
Aspect Ratio  
Timings  
Enter  
Auto  
Enter  
Auto Image  
Execute  
Presentation  
Display Mode  
2. Press“Light Source”->”Mode”, select power, then“Power”function will be activated. Select“Power”and adjust  
“0,1,2……10”levels of power adjustment, the users can set desired constant light output level.  
3. Choose“Constant”to select“Enable”or“Disable”, the projector will keep the preset brightness level for certain  
period of time until the light source decay to this level.  
4. When“Constant”is disabled, then the“Color  
Calibrate”will be workable from“grey”to“black”,  
Light source  
in case the users want to calibrate the constant  
function, or after replacing main board or light engine,  
or both.  
Mode  
Normal  
Off  
High Altitude  
Power  
Constant  
Enable  
Color Calibration  
Execute  
Notes:  
y
y
The color temperature will be not a constant value when the constant light output function is activated.  
It is suggested to set the power below level 10 (full power), in order to remain allowance to maintain the  
constant light output for a period of time.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Troubleshooting  
5. TROUBLESHOOTING  
Overview  
y
y
y
Image Problems  
LED Indication Chart  
Warning Message  
Note: If you experience a problem with your projector, please refer to the following information. If a problem  
persists, please contact your local reseller or service center.  
5.1 Image Problems  
y
No image appears on-screen  
-
Ensure all the cables and power connections are correctly and securely connected as described in the“In-  
stallation”section.  
-
-
Check if all pins are ok in the connector.  
Check if the projection laser has been securely installed.  
Note: This projector can not display 1920*1200 resolution but only 1920*1200 RB (reduce blanking).  
y
Partial, scrolling or incorrectly displayed image  
-
If you are using a PC (for Windows 95, 98, 2000, XP, Windows 7):  
`
`
`
`
Open the“My Computer”icon, the“Control Panel”folder, and then double click on the“Display”icon.  
Select the“Settings”tab.  
Verify that your display resolution setting is lower than or equal to WUXGA (1920 × 1200).  
Click on the“Advanced Properties”button. If the projector is still not projecting the whole image, you will  
also need to change the monitor display you are using. Refer to the following steps.  
`
`
`
Verify the resolution setting is lower than or equal to WUXGA (1920 × 1200).  
Select the“Change”button under the“Monitor”tab.  
Click on“Show all devices”. Next, select“Standard monitor types”under the SP box; choose the resolu-  
tion mode you need under the“Models”box.  
` Verify that the resolution setting of the monitor display is lower than or equal to WUXGA (1920 × 1200).  
If you are using a Notebook:  
-
`
`
First, follow the steps above to adjust resolution of the computer.  
Press the appropriate keys listed below for your notebook manufacturer to send signal out from notebook  
to projector. Example: [Fn]+[F4]  
Acer  
[Fn]+[F5]  
[Fn]+[F8]  
[Fn]+[F8]  
[Fn]+[F4]  
IBM/Lenovo [Fn]+[F7]  
HP/Compaq [Fn]+[F4]  
Asus   
Dell   
Gateway  
NEC   
[Fn]+[F3]  
Toshiba   
[Fn]+[F5]  
Mac Apple:  
System Preference Display Arrangement Mirror  
display  
-
-
If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the  
projector.  
The recommended resolution per projector is the native resolution so PGWX-62L/PGWX-62L-K 1280×800  
and PGWU-62L/PGWU-62L-K 1920×1200.  
y
The screen of the Notebook or PowerBook computer is not displaying your presentation  
-
If you are using a Notebook PC  
Some Notebook PCs may deactivate their own screens when a second display device is in use. Each of  
them has a different way to be reactivated. Please refer to your computer’s manual for detailed information.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Troubleshooting  
y
y
y
y
Image is unstable or flickering  
-
-
Use“TIMINGS\H PHASE”to correct it.  
Change the monitor color setting on your computer.  
Image has vertical flickering bar  
-
-
Use“AUTO IMAGE”to make an adjustment.  
Check and reconfigure the display mode of your graphic card to make it compatible with the projector.  
Image is out of focus  
-
-
Adjust lens focus to fit.  
Make sure the projection screen is between the required distance.  
The image is stretched when displaying 16:9 DVD title  
-
When you play anamorphic DVD or 16:9 DVD, the projector will show the best image when the projector  
display mode is set to 16:9 in the OSD.  
-
-
-
If you play 4:3 format DVD titles, please change the format to 4:3 in the projector OSD.  
If the image is still stretched, you will also need to adjust the aspect ratio by referring to the following:  
Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player.  
y
y
Image is too small or too large  
-
Adjust lens zoom to fit. If it does not fill the screen properly, please change the correct lens or change the  
position of the projector.  
Image has slanted sides  
Reposition the projector so that it is perpendicular to the screen.  
-
5.2 LED Indication Chart  
Status LED  
1 sec  
1 sec  
1 sec  
1 sec  
1 sec  
Off/STBY  
On  
Error  
During Start-up  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Troubleshooting  
5.3 Warning Message  
Message  
Description  
Overheating:  
When you see the warning message, it means the  
temperature is over operational temperature.  
Over Temperature  
Note: Please contact service people when you see those warning messages!  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
6. Maintenance & Service  
6. MAINTENANCE & SERVICE  
Overview  
y
Replacing the Lens  
6.1 Replacing the Lens  
Warning: This procedure may only be performed by qualified technical service personnel.  
Procedure:  
1
1. Turn the projector off and unplug the power cord.  
2
2. Allow the projector to cool down for at least 1 minute then start the lens replacement.  
3
3. Remove the lens cover from the projector.  
4
4. Rotate the bar upwards and then rotate the lens counterclockwise to remove it from the projector.  
5. Replace the lens to be installed, be sure the label“TOP”of lens is upward and then push the lens into the  
5
position.  
6
6. Rotate the lens clockwise to lock the lens and then rotate the bar downwards.  
7
7. Put the lens cover to the projector with the sound“click”.  
3
4
1
2
HDMI  
VGA-IN  
DVI  
LAN  
RS-232  
12V  
OUT  
5V  
OUT  
CVBS  
5
6
7
Caution: Do not transport the projector with any lens installed.  
Note: Please verify that all the plastic caps removed from the lens prior inserting in the projector.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Specifications  
7. SPECIFICATIONS  
Overview  
y
y
y
y
PGWU-62L / PGWU-62L-K  
PGWX-62L / PGWX-62L-K  
Dimensions  
Compatibility Modes  
7.1 PGWU-62L / PGWU-62L-K  
Specifications  
PGWU-62L / PGWU-62L-K  
WUXGA single-chip DLP projector  
Projector type  
Technology  
0.67”DMD  
1,920 x 1,200 WUXGA  
6,000 ANSI lumens*  
11,000:1*  
Resolution  
Brightness  
Contrast ratio  
Brightness uniformity  
Aspect Ratio  
Lens type  
90%*  
16:10  
G lens  
Lenses  
1.221.53:1; 0.951.22:1; 1.522.92:1; 2.90~5.50  
Optical lens shift  
Color correction  
Light source  
Vertical: -100% to +100% / horizontal: -30% to +30%  
Yes  
Laser diode  
Light source lifetime  
Sealed DLP™ core  
20,000 hours (bright mode)  
Yes  
Advance Picture in Picture Yes  
Orientation  
Ceiling/floor, front/rear, 360 degree free installation, portrait  
Integrated web server  
3D  
Yes  
N/A  
Keystone correction  
Inputs  
app. +/-20° vertical  
VGA-in,VGA-out, HDMI, DVI, CVBS, LAN, RS232, 12V out, 5V out;  
up to WUXGA (1,920 x 1,200) 60Hz  
Input Resolutions  
(*) Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Specifications  
Specifications  
PGWU-62L / PGWU-62L-K  
Software tools  
Control  
Projector Toolset  
IR, RS232, RJ45  
Network connection  
Power requirements  
Max. power consumption  
10/100 base-T, RJ-45 connection  
100-240V / 50-60Hz  
580W  
Noise level (typical at  
35 dBA (bright mode)/ 32 dBA (eco mode)  
25°C/77°F)  
Operational ambient  
temperature  
5-40°C / 41°-104°F (sea level)  
Operating humidity  
Dimensions (W x L x H)  
Weight  
10-85%  
506 x 516 x 251 mm (without cable cover)  
17.5 kg  
Shipping dimensions  
(WxLxH)  
796 x 595 x 378mm  
Standard accessories  
Certifications  
Power cord, wireless remote control, lens cover  
CB test certificate, US emc, US safety, CE emc and safety, CCC emc  
and safety  
Warranty  
Limited 3 years parts and labor. Extendable up to 5.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Specifications  
7.2 PGWX-62L / PGWX-62L-K  
Specifications  
PGWX-62L / PGWX-62L-K  
WXGA single-chip DLP projector  
Projector type  
Technology  
0.65”DMD  
1,280 x 800 WXGA  
6,000 ANSI lumens*  
11,000:1*  
Resolution  
Brightness  
Contrast ratio  
Brightness uniformity  
Aspect Ratio  
Lens type  
90%*  
16:10  
G lens  
Lenses  
1.281.60:1; 1.001.28:1; 1.613.07:1; 3.04 ~ 5.78  
Optical lens shift  
Light source  
Vertical: -100% to +100% / horizontal: -30% to +30%  
Laser diode  
Light source lifetime  
Sealed DLP™ core  
20,000 hours (bright mode)  
Yes  
Advance Picture in Picture Yes  
Orientation  
Ceiling/floor, front/rear, 360 degree free installation, portrait  
Integrated web server  
3D  
Yes  
Yes (DLP link)  
app. +/-20° vertical  
Keystone correction  
Inputs  
VGA-in,VGA-out, HDMI, DVI, CVBS, LAN, RS232, 12V out, 5V out;  
Input Resolutions  
Software tools  
Control  
up to WUXGA (1,920 x 1,200) 60Hz  
Projector Toolset  
IR, RS232, RJ45  
Network connection  
Power requirements  
Max. power consumption  
10/100 base-T, R-J45 connection  
100-240V / 50-60Hz  
580W  
Noise level (typical at  
35 dBA (bright mode)/ 32 dBA (eco mode)  
25°C/77°F)  
(*) Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Specifications  
Specifications  
PGWX-62L / PGWX-62L-K  
5-40°C / 41°-104°F (sea level)  
Operational ambient  
temperature  
Operating humidity  
Dimensions (W x L x H)  
Weight  
10-85%  
506 x 516 x 251 mm (without cable cover)  
17.5 kg  
Shipping dimensions  
(WxLxH)  
796 x 595 x 378mm  
Standard accessories  
Certifications  
Power cord, wireless remote control, lens cover  
CB test certificate, US emc, US safety, CE emc and safety, CCC emc  
and safety  
Warranty  
Limited 3 years parts and labor. Extendable up to 5.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Specifications  
7.3 Dimensions  
Projector Outer Dimensions  
Rear View  
Front View  
Top View  
Right Side View  
Left Side View  
Bottom View  
Dimensions given in millimeters.  
WARNING:  
y
Be sure to use the correct screw size. Screw Length will vary depending on the thickness of the mount-  
ing plate.  
y
y
Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.  
Avoid installing the projector near a heat source.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Specifications  
7.4 Compatibility Modes  
Frequency  
Signal  
NTSC  
Resolution  
H. (KHz)  
V. (Hz)  
Video  
Digital Analog  
Remark  
--  
15.734  
15.625  
31.5  
60  
50  
--  
--  
--  
--  
--  
640×350  
640×400  
640×480  
640×480  
640×480  
640×480  
640×480  
800×600  
800×600  
800×600  
800×600  
800×600  
1024×768  
1024×768  
1024×768  
1024×768  
1280×720  
1280×720  
1280×768  
1280×768  
1280×768  
1280×800  
1280×960  
1280×960  
1280×960  
1440×900  
1280×1024  
1280×1024  
1280×1024  
1400×1050  
1600×1200  
1920×1080  
1920×1080  
1920×1080  
70.1  
85.1  
60  
70Hz  
85Hz  
PAL/SECAM  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
--  
37.9  
31.5  
67  
VGA  
37.9  
37.5  
43.3  
35.2  
37.9  
46.9  
48.1  
53.7  
48.4  
56.5  
60  
72.8  
75  
72Hz  
85  
56.3  
60.3  
75  
56Hz  
60Hz  
SVGA  
XGA  
72.2  
85.1  
60  
72Hz  
85Hz  
70.1  
75  
70Hz  
68.7  
85  
50  
HD720  
WXGA  
60  
47.776  
60  
75  
85  
60  
60  
WXGA-800  
75  
85  
74.98  
60  
64  
80  
SXGA  
75  
91.1  
85  
SXGA+  
UXGA  
60  
--  
75  
60  
24  
HD1080  
WUXGA  
50  
60  
Only support  
[RB] timing  
1920×1200  
60  
--  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Specifications  
Frequency  
Signal  
Resolution  
H. (KHz)  
V. (Hz)  
Video  
Digital Analog  
Remark  
1920×1080  
1920×1080  
1920×1080i  
1920×1080i  
1920×1080p  
1920×1080p  
1920×1080p  
1920×1080p  
1920×1080p  
1280×720  
33.8  
28.1  
30  
25  
50  
60  
24  
25  
30  
50  
60  
60  
50  
60  
50  
50  
50  
60  
60  
60  
--  
--  
--  
--  
28.125  
33.75  
--  
--  
--  
--  
--  
--  
--  
HDTV  
45  
--  
--  
--  
--  
--  
--  
1280×720p  
1280×720p  
720×576  
--  
--  
31.3  
720×576i  
15.625  
--  
--  
720×576p  
SDTV  
720×480  
31.5  
15.734  
31.5  
720×480i  
--  
--  
720×480p  
3D Timing - 120 Hz Frame Sequential  
Frame Rate in Hz  
(Vertical Frequency)  
Line Rate in KHz  
(Horizontal Frequency)  
76.92  
Input Source Resolution  
Pixel Clock in MHz  
SVGA (800×600)  
XGA (1024×768)  
720p (1280×720)  
119.63  
120.13  
120.31  
83.725  
139.276  
161.997  
98.87  
92.88  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Environmental information  
8. ENVIRONMENTAL INFORMATION  
Overview  
y
y
Disposal information  
RoHS compliance  
8.1 Disposal information  
Disposal Information  
Waste Electrical and Electronic Equipment  
This symbol on the product indicates that, under the European Directive 2002/96/EC governing waste from  
electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dis-  
pose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical  
and electronic equipment.To prevent possible harm to the environment or human health from uncontrolled waste  
disposal, please separate these items from other types of waste and recycle them responsibly to promote the sus-  
tainable reuse of material resources.  
For more information about recycling of this product, please contact your local city office or your municipal waste  
disposal service.  
For details, please visit the Barco website at:  
http://www.barco.com/en/AboutBarco/weee  
Disposal of batteries in the product  
This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed  
of separately from municipal waste.  
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical  
symbols will appear below the crossed-out wheeled bin symbol.  
By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential  
negative effects on the environment and human health.  
8.2 RoHS compliance  
Turkey RoHS compliancen  
Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur.  
[Republic of Turkey: In conformity with the EEE Regulation]  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
8. Environmental information  
中国大陆RoHS (Information for China ROHS compliance)  
根据中国大陆《电子信息产品污染控制管理办法》( 也称为中国大陆RoHS)，以下部份列出了本产品中可能包含的有  
毒有害物质或元素的名称和含量。  
10  
Table of toxic and hazardous substances/elements and their content, as required by China’s management methods  
for controlling pollution by electronic information products.  
Hazardous Substances Or Elements / 有毒有害物质或元素  
Lead  
(Pb) /  
铅(Pb)  
Mercury  
(Hg) /  
汞(Hg)  
Cadmium Chromium VI Polybrominated Polybrominated  
Diphenyl Ethers  
(PBDE) /  
(Cd) /  
镉(Cd)  
Compounds  
(Cr VI) /  
六价铬(Cr VI)  
Biphenyls  
(PBB) /  
Component Name /  
部件名称  
多溴联苯  
(PBB)  
多溴二苯醚  
(PBDE)  
Case/Enclosure /  
机壳  
O
X
O
O
O
O
O
O
O
O
Printed Circuit  
Assembly / 电子电路  
O
O
*
组件  
Chassis / 底座  
Engine / 引擎  
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Hardware / 硬件  
Optics / 光学器件  
* ：Printed Circuit Assembly includes all Printed Circuit Boards (PCBs) and their respective population of discrete com-  
ponents, ICs, and connectors.  
* ：电子电路组件包括所有包括所有印刷电路板(PCB)及其各自的离散组件、IC 及连接器。  
○：Indicates the hazardous and toxic substance content of the part is lower than the threshold defined by the SJ/  
T11364-2006 standard.  
○：表明该部件所含有害和有毒物质含量低于SJ/T11364-2006 标准定义的阈值。  
╳：Indicates the hazardous and toxic substance content of the part is over the threshold defined by the SJ/T11364-  
2006 standard. In all cases where an X is shown, Barco uses an allowable exemption per EU RoHS.  
╳：表明该部件所含有害和有毒物质含量高于SJ/T11364-2006 标准定义的阈值。对于所有显示为“X”的情况，Barco  
按照 EU RoHS 采用了容许的豁免指标。  
A급 기기 (업무용 방송통신기자재)  
이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며,  
가정외의 지역에서 사용하는 것을 목적으로 합니다.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Environmental information  
8.3 Production address  
Producer  
Barco nv Entertainment Division  
Noordlaan 5, B-8520 Kuurne  
Made in information  
The made in country is indicated on the product ID label on the product itself.  
Production date  
The month and year of production is indicated on the product ID label on the product itself.  
8.4 Importers contact information  
Contact  
To find your local importer, contact Barco directly or one of Barco’s regional offices via the contact information given  
on Barco’s web site, www.barco.com.  
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Download from Www.Somanuals.com. All Manuals Search And Download.  

AEG Washer 61 81 102 User Manual
Agri Fab Spreader 45 03881 User Manual
Akai Clock AR250P User Manual
Amana Range ACS7270A User Manual
American DJ DJ Equipment BPP 20 User Manual
Asus Computer Hardware V9950 User Manual
Athena Technologies Portable Speaker AS R1 User Manual
Axis Communications Security Camera Q6044 C User Manual
Behringer Indoor Furnishings LD6230 User Manual
Beko Oven OIM 25603 User Manual