Coronis Fusion 6MP
User Guide
MDCC-6230
Download from Www.Somanuals.com. All Manuals Search And Download.
Coronis Fusion 6MP
User Guide
MDCC-6230
K5902055/01
28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
Barco nv
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: +32 56.23.32.11
Fax: +32 56.26.22.62
Printed in Belgium
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
TABLE OF CONTENTS
1. Welcome! .......................................................................................... 3
1.1 About the product ............................................................................................. 3
1.2 What’s in the box.............................................................................................. 3
2.1 Display front view ............................................................................................. 5
2.2 Display rear view.............................................................................................. 6
3. Display installation .............................................................................. 7
3.1 Removing the covers ......................................................................................... 7
3.2 Unlocking the height mechanism............................................................................ 8
3.3 Adjusting the display position................................................................................ 9
3.4 Connecting the signal cables ................................................................................10
3.5 Connecting the power cable .................................................................................11
3.6 Routing the cables ............................................................................................11
3.7 Re-attaching the covers ......................................................................................11
3.8 VESA-mount installation .....................................................................................12
3.9 First time starting up ..........................................................................................14
4. Daily operation ................................................................................... 15
4.1 Recommendations for daily operation ......................................................................15
4.2 Key indicator lights............................................................................................16
4.3 Stand-by switching............................................................................................16
4.4 Bringing up the OSD menus .................................................................................17
4.5 Navigating through the OSD menus ........................................................................18
5.1 OSD menu position ...........................................................................................19
5.2 OSD menu language .........................................................................................19
5.3 OSD menu automatic close function........................................................................19
5.4 Power status indicator light ..................................................................................20
5.5 Key indicator lights............................................................................................20
5.6 Power lock function ...........................................................................................20
5.7 Keys sound ....................................................................................................21
5.8 Ethernet over USB ............................................................................................21
5.9 USB.............................................................................................................21
5.10 DPMS mode ...................................................................................................22
5.11 Hibernate.......................................................................................................22
5.12 Luminance target..............................................................................................23
5.13 Color presets ..................................................................................................23
5.14 Color temperature.............................................................................................24
5.15 Color coordinates .............................................................................................24
5.16 Viewing modes ................................................................................................24
5.17 Display functions ..............................................................................................25
5.18 Ambient Light Compensation (ALC) ........................................................................26
5.19 Reading rooms ................................................................................................26
5.20 Continuous ALC...............................................................................................27
5.21 Image scaling..................................................................................................27
5.22 Image source selection modes ..............................................................................28
5.23 Video input signals............................................................................................28
5.24 Video encoding modes .......................................................................................29
5.25 Grayscale conversion modes................................................................................30
5.26 EDID timings...................................................................................................30
5.27 Display info ....................................................................................................31
5.28 Display status..................................................................................................31
6.1 Cleaning instructions .........................................................................................33
K5902055 CORONIS FUSION 6MP 28/08/2013
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
7.1 Repacking your display.......................................................................................36
8.1 Safety information.............................................................................................37
8.2 Environmental information ...................................................................................38
8.3 Regulatory compliance information .........................................................................40
8.4 EMC notice ....................................................................................................41
8.5 Explanation of symbols.......................................................................................45
8.6 Legal disclaimer...............................................................................................46
8.7 Technical specifications ......................................................................................47
8.8 Open source license information ............................................................................48
2
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Welcome!
1. WELCOME!
1.1 About the product
Overview
Thank you for choosing this Coronis Fusion 6MP!
Coronis Fusion 6MP is an ingenious PACS display system designed to further enhance flexibility and
productivity in diagnostic imaging. Featuring the industry’s first 30-inch color LCD that can be used as two
seamless heads or one wide-screen display, Coronis Fusion 6MP offers you the freedom to organize your
workspace just the way you want it. It allows you to read CT, MR, cath and echo cardiogram images, or
any other combination, side by side on a single diagnostic screen. Coronis Fusion 6MP features the latest,
breakthrough In-Plane Switching (IPSPro) LCD technology. This technology brings the most advanced
LCD viewing characteristics on the market, setting new standards for brightness and contrast, even from
a wide viewing angle. Use the instructions in this guide to install your Coronis Fusion 6MP display and
discover all these interesting features yourself!
CAUTION: Read all the important safety information before installing and operating your
Coronis Fusion 6MP. Please refer to the dedicated chapter in this user guide.
1.2 What’s in the box
Overview
Your Coronis Fusion 6MP comes with:
•
•
•
•
•
•
•
this Coronis Fusion 6MP user guide
a system CD
two DVI cables
two DisplayPort cables
a USB cable
a set of AC power cords
an external power supply
If you ordered a Barco display controller, it’s also in the box together with its accessories. A dedicated
user guide is available on the system CD.
Keep your original packaging. It is designed for this display and is the ideal protection
during transport and storage.
K5902055 CORONIS FUSION 6MP 28/08/2013
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Welcome!
4
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Parts, controls and connectors
2. PARTS, CONTROLS AND
CONNECTORS
2.1 Display front view
Overview
8
1
2
3
4
5
6
7
Image 2-1
Front view
1
3
5
7
2
4
6
8
USB downstream connectors
Right/Down key
Left/Up key
Menu/Enter key
Stand-by/Cancel key
Control wheel
Power status indicator light
Ambient light sensor
K5902055 CORONIS FUSION 6MP 28/08/2013
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Parts, controls and connectors
2.2 Display rear view
Overview
1
2
3
4
5
6
7
8
9
10
11 12
Image 2-2
Rear view
1
3
2
4
+24 VDC power input
DVI 2 video input
+5 VDC, 0.5 A power output
DisplayPort 2 video input
Neck cover
5
6
Connector compartment cover
DisplayPort 1 video input
DVI 1 video input
7
8
Display stand cover
9
10
12
Ethernet connector (see note below)
USB downstream connector
11
USB upstream connector
The Ethernet connection is used for maintenance purposes and is not supported for
user application.
6
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Display installation
3. DISPLAY INSTALLATION
Prior to installing your Coronis Fusion 6MP and connecting all necessary cables, make
sure to have a suitable display controller physically installed in your computer. If you
are using a Barco display controller, please consult the user guide delivered with it to
do this.
3.1 Removing the covers
The connector compartment cover should be removed to get access to the connectors.
To remove the connector compartment cover
1. Gently lift the clips at one of the handles of the connector compartment cover to release that side of the
cover.
2. Do the same at the other side of the cover.
3. Remove the cover.
The display stand cover should be removed to get access to the cable routing channel.
To remove the display stand cover
1. Gently press and hold the clips at the inside top of the cover.
K5902055 CORONIS FUSION 6MP 28/08/2013
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Display installation
2. Slide the cover upwards while holding the clips pressed.
3.2 Unlocking the height mechanism
In the factory, the height-positioning system in the display stand is locked with a red
hook to prevent damage during transportation. You’ll have to remove this hook before
adjusting your display height position.
To remove the hook:
1. Position the display with its rear side facing you.
2. While holding the display panel pushed down, pull out the red hook in the display stand.
8
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Display installation
3. Keep the clip in the dedicated hole in case the display needs to be shipped later.
To retain the hook for possible future transportation, insert the short, red end of the
hook back into the stand of your display.
3.3 Adjusting the display position
Now that the height-positioning system of your display is unlocked, you can adjust the
display position.
To adjust the display position
1. Tilt, swivel, raise and lower the display as desired.
K5902055 CORONIS FUSION 6MP 28/08/2013
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Display installation
CAUTION: Do not try to pivot your display when attached to the stand. Trying to do so
could cause serious damage to your display and its stand.
3.4 Connecting the signal cables
Each side of your display can have a different video input connected (one side can have
DVI connected while the other side has DisplayPort connected). Both display sides can
have the same video input connected as well but only one video input is allowed on each
side of your display.
To connect the signal cables to the display:
1. Connect one head of the display controller to the DVI 1 or DisplayPort 1 connector with one of the
supplied DVI or DisplayPort cables.
2. Connect another head of the display controller to the DVI 2 or DisplayPort 2 connector with one of the
supplied DVI or DisplayPort cables.
3. If you want to make use of your display’s USB downstream connectors, connect a PC USB downstream
connector to the display’s USB upstream connector by means of the supplied USB 2.0 cable.
10
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Display installation
3.5 Connecting the power cable
To connect the power cable to the display:
1. Connect the supplied external DC power supply to the +24 VDC power input of your Coronis Fusion
6MP display.
2. Plug the other end of the external DC power supply into a grounded power outlet by means of the proper
power cord delivered in the packaging.
3.6 Routing the cables
To route the cables
1. Route all connected cables through the cable routing channel in the stand of your display.
Tip: The cable straps at the inside of the connector compartment allow you to fix the cables for better
shielding of the cables.
3.7 Re-attaching the covers
To re-attach the display stand cover
1. Slide the display stand cover downward. You’ll hear a “click” sound of the cover’s clips when the display
stand cover is in position.
K5902055 CORONIS FUSION 6MP 28/08/2013
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Display installation
Pay attention that all cables stay in the cable channel while re-attaching the cover.
To re-attach the connector compartment cover
1. Slide the cover’s top in position and then push the cover’s bottom. You’ll hear a “click” sound of the
cover’s clips when the connector compartment cover is in position.
3.8 VESA-mount installation
WARNING: Use an arm that is approved by VESA (according to the VESA 100 mm stan-
dard).
Use an arm that can support the weight of the display. Refer to the technical specifica-
tions of this display for the applicable weight.
CAUTION: You should mount the panel in landscape position. Portrait position is pos-
sible but not supported.
Overview
The panel, standard attached to a stand, is compatible with the VESA 100 mm standard. Thus, it can be
used with an arm that is approved by VESA. This chapter shows you how to release the panel from the
stand and how to attach it to an arm. If you’re not using an arm, you can skip this chapter.
12
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Display installation
1. Gently pull open both lower sides of the cover.
2. Slide the cover upwards while holding the lower sides pulled open.
3. Lift the plastic frame that covers the fixation of the panel to the stand. Turn it for 45 degrees to uncover
the fixation screws.
4. Unscrew the four fixation screws fixing the panel to the stand.
5. Attach the panel firmly to the arm using 4 screws M4 x 10 mm.
K5902055 CORONIS FUSION 6MP 28/08/2013
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Display installation
WARNING: Never move a display attached to an arm by pulling or pushing the display
itself. Instead, make sure that the arm is equipped with a VESA approved handle and
use this to move the display.
Please refer to the instruction manual of the arm for more information and instructions.
3.9 First time starting up
Overview
You are now ready to start up your Coronis Fusion 6MP for the first time.
2. Turn on the computer connected to your display.
If you have properly installed your display and display controller, the Windows start-up messages will
appear once the boot procedure is finished.
Your Coronis Fusion 6MP display will be running in a basic video mode at a default re-
fresh rate when first time starting up. If you are using a Barco display controller, please
consult the dedicated user guide available on the system CD to install the drivers, soft-
ware and documentation. When this is done, your display will automatically detect the
connected video input signal(s) and apply the correct video mode and refresh rate.
14
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Daily operation
4. DAILY OPERATION
4.1 Recommendations for daily operation
Optimize the lifetime of your display
Enabling the Display Power Management System (DPMS) of your display will optimize its diagnostic life-
time by automatically switching off the backlight when the display is not used for a specified period of time.
By default, DPMS is enabled on your display, but it also needs to be activated on your workstation. To do
this, go to “Power Options Properties” in the “Control Panel”.
Barco recommends setting DPMS activation after 20 minutes of non-usage.
Use a screen saver to avoid image retention
Prolonged operation of an LCD with the same content on the same screen area may result in a form of
image retention.
You can avoid or significantly reduce the occurrence of this phenomenon by using a screen saver. You
can activate a screen saver in the “Display properties” window of your workstation.
Barco recommends setting screen saver activation after 5 minutes of non-usage. A
good screen saver displays moving content.
In case you are working with the same image or an application with static image elements for several hours
continuously (so that the screen saver is not activated), change the image content regularly to avoid image
retention of the static elements.
Understand pixel technology
LCD displays use technology based on pixels. As a normal tolerance in the manufacturing of the LCD, a
limited number of these pixels may remain either dark or permanently lit, without affecting the diagnostic
performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its
LCD panels.
To learn more about LCD technology and missing pixels, consult the dedicated white
Enhance user comfort
Every Barco multi-head display system is color matched with the highest specifications in the market.
Barco recommends keeping color-matched displays together. Furthermore, it is impor-
tant to use all displays of a multi-head configuration at the same rate to preserve color
matching throughout the economic lifetime of the system.
K5902055 CORONIS FUSION 6MP 28/08/2013
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Daily operation
Maximize quality assurance
The ’MediCal QAWeb’ system offers online service for high-grade Quality Assurance, providing maximum
diagnostic confidence and uptime.
Barco recommends to install MediCal QAWeb Agent and apply the default QAWeb policy
at least. This policy includes calibration on regular intervals. Connecting to MediCal
QAWeb Server offers even more possibilities.
Learn more and sign up for the free MediCal QAWeb Essential level at
4.2 Key indicator lights
To make the keys light up:
1. Gently sweep your finger over the bottom right hand side of your display.
As a result, the keys will light up and are now available for further actions. However, if no further actions
are taken within the following 5 seconds, the key indicator lights will dim again.
dicator lights", page 20 for detailed instructions on how to do this.
4.3 Stand-by switching
The connected power supply also provides a switch that can be used to turn the power
completely off. To use the display, please make sure to switch on this power supply.
This can be done by pushing the on/off switch on the power supply into the “│” position.
16
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Daily operation
Switching on the display while it is in stand-by mode or vice versa can both be done by
using the keys or by using the control wheel.
To switch your display on using the keys:
1. Light up the keys indicator lights as previously described.
2. While the keys are light up, touch the Stand-by/Cancel key for approximately 2 seconds.
As a result, the display will switch on and the power status indicator light is dimmed.
To switch your display on using the control wheel:
1. Press the control wheel for approximately 2 seconds.
As a result, the display will switch on and the power status indicator light is dimmed.
cator light", page 20 for detailed instructions on how to do this.
To switch your display to Stand-by using the keys:
1. Light up the keys indicator lights as previously described.
2. While the keys are light up, touch the Stand-by/Cancel key, a small window pops-up. Press the button
again to confirm.
As a result, the display will switch to stand-by mode and the power status indicator light is orange.
To switch your display to Stand-by using the control wheel:
1. Press the control wheel once, a small window pops-up. Press the control wheel again to confirm.
As a result, the display will switch to stand-by mode and the power status indicator light is orange.
In case of a power outage recovery, your display will always start-up in the power mode
it was in before the power interruption (i.e. stand-by or on). This protects your display
against inadvertent image retention problems.
4.4 Bringing up the OSD menus
About OSD menu
The OSD menu allows you to configure different settings to make your Coronis Fusion 6MP display fit your
needs within your working environment. Also, you can retrieve general information about your display and
its current configuration settings through the OSD menu.
Bringing up the OSD menus can be done by using the keys or by using the control wheel.
How to bring up the OSD menus using the keys
1. If not already done so, switch on the display as previously described.
2. Light up the keys indicator lights as previously described.
3. While the keys light up, touch the Menu/Enter key.
As a result, the OSD main menu comes up in the bottom right corner of the screen. If no further actions
are taken within the following 90 seconds however, the OSD menu will disappear again.
K5902055 CORONIS FUSION 6MP 28/08/2013
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Daily operation
How to bring up the OSD menus using the control wheel
1. If not already done so, switch on the display as previously described.
2. Shortly turn the control wheel.
As a result, the OSD main menu comes up in the bottom right corner of the screen. If no further actions
are taken within the following 90 seconds however, the OSD menu will disappear again.
The OSD menu auto-exit function can be disabled in the OSD menu. Please refer to
"OSD menu automatic close function", page 19 for detailed instructions on how to do
this.
position", page 19 for detailed instructions on how to do this.
4.5 Navigating through the OSD menus
About OSD menu navigation
Navigating through the OSD menu can be done by using the keys or by using the control wheel.
How to navigate through the OSD menus using the keys
1. Use the Right/Down and Left/Up keys to move through the (sub)menus, change values or make selec-
tions.
2. To go into a submenu or confirm adjustments and selections, use the Menu/Enter key.
3. Use the Stand-by/Cancel key to cancel adjustments or exit a (sub)menu.
4. Exit the OSD menu by touching the Stand-by/Cancel key for approximately 2 seconds.
How to navigate through the OSD menus using the control wheel
1. Rotate the control wheel to move through the menus, change values or make selections.
2. To go into a submenu or confirm adjustments and selections, shortly click the control wheel.
3. Click the control wheel for approximately 2 seconds to cancel adjustments or exit a (sub)menu.
18
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
5. ADVANCED OPERATION
5.1 OSD menu position
About the OSD menu position
By default, the OSD menu comes up in the bottom center position of the screen. This position can be
modified however. There’s choice from a number of predefined positions.
To change the position of the OSD menu:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > User Interface > Menu menu.
3. Enter the Position submenu.
4. Select one of the available OSD menu positions and confirm.
5.2 OSD menu language
About the OSD menu language
By default, the OSD menu comes up in English. However, there’s a wide range of other languages avail-
able for the OSD menu of your Coronis Fusion 6MP.
To change the language of the OSD menu:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > User Interface > Menu menu.
3. Enter the Language submenu.
4. Select one of the available languages and confirm.
5.3 OSD menu automatic close function
About the OSD menu automatic close function
By default, the OSD menu will disappear automatically after approximately 90 seconds of inactivity. How-
ever, this function can be disabled so that the OSD menu remains on the screen until manually closed.
To enable/disable the OSD menu automatic close function:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > User Interface > Menu menu.
3. Enter the Automatic Close submenu.
4. Select Enabled/Disabled as desired and confirm.
K5902055 CORONIS FUSION 6MP 28/08/2013
19
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
5.4 Power status indicator light
About the power status indicator light
By default, when the display is switched on, the power status indicator light is dimmed. This behavior can
be changed so that the power status indicator light will be blue when the display is switched on.
When the display is in stand-by mode, the power status indicator light will always turn
orange, even when the power status indicator light is disabled.
To enable/disable the power status indicator light:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > User Interface > Indicator Lights menu.
3. Enter the Power Status submenu.
4. Select Enabled/Disabled as desired and confirm.
5.5 Key indicator lights
About the key indicator lights
By default, after lighting up, the key indicator lights will dim again if no further actions are taken within the
following 5 seconds. However, this behavior can be changed so that the key indicator lights are always
on or always off.
To configure the key indicator lights
1. Bring up the OSD main menu.
2. Navigate to the Configuration > User Interface > Indicator Lights menu.
3. Enter the Keys submenu.
4. Select Automatic/Always On/Always Off as desired and confirm.
5.6 Power lock function
About the power lock function
By enabling the power lock function, the Coronis Fusion 6MP is forced to remain switched on. This means
that it can’t be switched to stand-by mode until the power lock function is disabled again.
To enable/disable the power lock function:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > User Interface > Controls menu.
3. Enter the Power Lock submenu.
4. Select Enabled/Disabled as desired and confirm.
20
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
5.7 Keys sound
About keys sound
By default, the keys will make a “beep” sound on every touch. However, this sound can be disabled so
that no sound will be heard when using the keys.
To enable/disable the keys sound:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > User Interface > Controls menu.
3. Enter the Sound submenu.
4. Select Enabled/Disabled as desired and confirm.
5.8 Ethernet over USB
About Eth. over USB
By default, the Ethernet over USB will be disabled. This does not disable the USB hub and still allows
to make use of the display’s USB downstream connectors and any external devices connected to it (key-
board, mouse, ...).
Please note that a connection from a PC USB downstream connector to the display’s USB upstream
connector is required to be able to use this functionality.
By enabling the Ethernet over USB, you allow the internal Coronis Fusion 6MP processor to communicate
directly over USB with the connected PC.
Enabling the Ethernet over USB is only recommended when you are using a non-Barco
display controller. If you are using a Barco display controller, this communication will
automatically be done over the connected video cable(s).
To enable/disable the eth. over USB:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Connectivity menu.
3. Enter the Eth. over USB submenu.
4. Select Enabled/Disabled as desired and confirm.
5.9 USB
About USB
By default, USB will be enabled. This will allow the connected PC to communicate directly over USB with
the internal Coronis Fusion 6MP processor.
By disabling USB, communication between the internal Coronis Fusion 6MP processor and the connected
PC will not be possible. This does not disable the USB hub and still allows to make use of the display’s
USB downstream connectors and any external devices connected to it (keyboard, mouse, ...).
Please note that a connection from a PC USB downstream connector to the display’s USB upstream
connector is required to be able to use this functionality.
K5902055 CORONIS FUSION 6MP 28/08/2013
21
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
Enabling the USB endpoint is only recommended when you are using a non-Barco dis-
play controller. If you are using a Barco display controller, this communication will au-
tomatically be done over the connected video cable(s).
To enable/disable USB:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Connectivity menu.
3. Enter the USB submenu.
4. Select Enabled/Disabled as desired and confirm.
5.10 DPMS mode
About DPMS mode
Enabling the Display Power Management System (DPMS) mode on your display will optimize its diagnos-
tic lifetime by automatically switching off the backlight when the display is not used for a specified period
of time. By default, DPMS mode is enabled on your display, but it also needs to be activated on your
workstation. To do this, go to the “Power options properties” window of your workstation.
Barco recommends setting DPMS activation after 20 minutes of non-usage.
When DPMS mode is enabled on your display, an additional OSD power saving function
on hibernation and how to enable this function.
To enable/disable DPMS mode on your display:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Power Management menu.
3. Enter the DPMS Mode submenu.
4. Select Enabled/Disabled as desired and confirm.
5.11 Hibernate
About hibernate
Enabling hibernation will not only switch off the backlight but will also force the display to disable other
functionalities so that power consumption is further reduced to a minimum. This happens after a specific
period of time which can be manually adjusted.
Hibernate can only be enabled on your display when the DPMS mode is enabled first.
22
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
To enable/disable hibernation on your display:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Power Management menu.
3. Enter the Hibernate submenu.
4. Select Enabled/Disabled as desired and confirm.
To specify the hibernate timeout:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Power Management menu.
3. Enter the Hibernate Timeout submenu.
4. Set the timeout value as desired and confirm.
5.12 Luminance target
About the luminance target
The luminance target of your Coronis Fusion 6MP is adjustable over a predefined range. When you
change the luminance target, the display will adjust its backlight to reach the target.
To set the luminance target:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Calibration menu.
3. Enter the Luminance Target submenu.
4. Set a luminance target value as desired and confirm.
The default value is 450 cd/m². The five year warranty is valid for this setting.
5.13 Color presets
About color presets
The available color preset settings for your display are:
Clearbase
Bluebase
User
Simulation of the clearbase film color temperature.
Simulation of the bluebase film color temperature.
When selecting the User color temperature setting,
you will be able to manually define the X and Y
coordinates or the display color temperature in
separate submenus.
Native White
The native, unmodified color temperature of the
LCD panel.
To select a color preset:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Calibration > Color Settings menu.
K5902055 CORONIS FUSION 6MP 28/08/2013
23
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
3. Enter the Color Presets submenu.
4. Select one of the available Color Presets and confirm.
5.14 Color temperature
About color temperature:
It is possible to change the color temperature of your display.
Color temperature can only be changed on your display when color presets is set to
To change the color temperature:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Calibration > Color Settings menu.
3. Enter the Color Definition submenu.
4. Select Color Temperature and confirm.
5. Enter the Color Temperature submenu.
6. Set the Temperature value as desired and confirm.
5.15 Color coordinates
About color coordinates:
It is possible to change the color coordinates of your display.
Color coordinates can only be changed on your display when color presets is set to
To change the color coordinates:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Calibration > Color Settings menu.
3. Enter the Color Definition submenu.
4. Select Color Coordinates and confirm.
5. Enter the X and/or Y submenu.
6. Set the coordinate value for X and/or Y as desired and confirm.
5.16 Viewing modes
About viewing modes
The Coronis Fusion 6MP can be used in two viewing modes:
24
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
Diagnostic
Text
This mode provides the full calibrated luminance
and is intended for using the display for diagnostic
purposes.
In this mode, the luminance is reduced to
approximately half of the luminance. This
is intended for using the display with office
applications such as word processing.
Please note that text mode is not persistent, once
powered off, the unit will restart in diagnostic mode.
As the Coronis Fusion 6MP is intended to be used in a diagnostic environment, the di-
agnostic mode should always be selected.
To select a viewing mode:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Calibration menu.
3. Enter the Viewing Mode submenu.
4. Select Diagnostic/Text as desired and confirm.
5.17 Display functions
About display functions
Native, uncorrected panels will display all grayscale/color levels with luminance increments that are not
optimal for crucial diagnostic information. Studies have shown however, that in medical images certain
grayscale/color parts contain more diagnostic information then others. To respond to these conclusions,
display functions have been defined. These functions emphasize on these parts containing crucial diag-
nostic information by correcting the native panel behavior.
Native
If you select Native, the native panel behavior will
not be corrected.
Dynamic Gamma 1.8
Dynamic Gamma 2.2
These are gamma functions that are shifted to take
into account the non-zero luminance of an LCD
panel when driven with a “black” signal. They are
especially useful in CT applications to improve the
perception of low Hounsfield values.
DICOM
DICOM (Digital Imaging and Communications
in Medicine) is an international standard that
was developed to improve the quality and
communication of digital images in radiology.
In short, the DICOM display function results in
more visible grayscales in the images. Barco
recommends selecting the DICOM display function
for most medical viewing applications.
User
This display function will be automatically selected
when display functions are defined by MediCal
QAWeb.
Gamma 1.8
Gamma 2.2
Select one of these display functions in case the
display is to replace a CRT display with a gamma
of 1.8 or 2.2 respectively.
To select a display function:
1. Bring up the OSD main menu.
K5902055 CORONIS FUSION 6MP 28/08/2013
25
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
2. Navigate to the Configuration > Calibration menu.
3. Enter the Display Function submenu.
4. Select one of the available display functions and confirm.
5.18 Ambient Light Compensation (ALC)
About ALC
Ambient Light Compensation (ALC) can only be enabled on your display when the DI-
25 to correctly set the display function.
When ALC is enabled, the DICOM display function will be recalculated taking a preset ambient light cor-
rection value into account. This value is determined by the selected reading room. Therefore, it is also
important to select a realistic reading room when enabling ALC. This can be done by following the instruc-
To enable/disable ALC:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Calibration > Ambient Light menu.
3. Enter the Ambient Light Compensation submenu.
4. Select Enabled/Disabled as desired and confirm.
5.19 Reading rooms
About reading rooms
Reading rooms can only be selected when the DICOM display function is selected.
function.
The American Association of Physicists in Medicine (AAPM) composed a list of pre-defined reading rooms.
Each of these reading rooms are defined by following parameters:
•
•
the maximum light allowed in this type of room
the preset ambient light correction value for this reading room
These parameters are stored in your display and determine the preset ambient light correction value to
take into account to recalculate the DICOM display function when Ambient Light Compensation (ALC) is
The available reading rooms for your Coronis Fusion 6MP are:
CR/DR/ MAMMO
CT/MR/NM
Corresponds to light conditions in diagnostic
reading rooms for computed radiology, digital
radiology or mammography. This setting has the
lowest maximum ambient light.
Corresponds to light conditions in diagnostic
reading rooms for computed tomography, magnetic
resonance or nuclear medicine scans.
26
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
Staff Office
Corresponds to light conditions in office rooms.
Clinical Viewing Room
Corresponds to light conditions in diagnostic
reading rooms for clinical viewing.
Emergency Room
Operating Room
Corresponds to light conditions in emergency
rooms.
Corresponds to light conditions in operating rooms.
This setting has the highest maximum ambient light.
To select a reading room:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Calibration > Ambient Light menu.
3. Enter the Reading Room submenu.
4. Select one of the available reading rooms and confirm.
5.20 Continuous ALC
About Continuous ALC
Continuous ALC can only be selected when the DICOM display function is selected.
tion.
Enabling continuous ALC will continuously recalculate the DICOM display function taking the averaged
ambient light into account.
To select continuous ALC:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Calibration > Ambient Light menu.
3. Enter the Continuous ALC submenu.
4. Select Enabled/Disabled as desired and confirm.
5.21 Image scaling
About image scaling
Enabling image scaling will multiply each individual pixel to one or more adjacent pixels so that the size
of the displayed image will be a multiple of the original image source video input signal.
Image scaling is only possible when the resolution of your display’s video input signal
is less than or equal to half the maximum resolution of the display.
To enable/disable image scaling:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Image Source menu.
3. Enter the Scaling submenu.
4. Select Enabled/Disabled as desired and confirm.
K5902055 CORONIS FUSION 6MP 28/08/2013
27
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
5.22 Image source selection modes
About image source selection modes
Your Coronis Fusion 6MP automatically detects the number of video input signals connected, attaches
them to the correct display side and applies the correct video settings to it (resolution, video encoding
mode, refresh rate,...). However, it may be needed to manually select the video input signal(s) to be
displayed on a certain display side or to adjust certain video settings yourself. The start to this is selecting
one of the following image source selection modes available for your display:
Automatic
In this mode, your display automatically detects the
connected video input signals, attaches them to the
correct display side and applies the correct video
settings to it (resolution, video encoding mode,
refresh rate,...). No video settings are available
when this mode is selected.
One Image Source
Two Image Sources
This mode is intended for displaying and manually
configuring only one connected video input signal.
When selecting this mode, the video settings
become available for the selected video input
signal.
This mode is intended for displaying and manually
configuring two connected video input signals (one
on each display side). When selecting this mode,
the video settings become available for the selected
video input signal on each side of the display.
To select an image source selection mode:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Image Sources menu.
3. Enter the Image Source Selection submenu.
4. Select one of the available image source selection modes and confirm.
5.23 Video input signals
Your Coronis Fusion 6MP display automatically detects the connected video input sig-
nals. Manually selecting image source video input signals is possible, but then your
display’s image source selection mode should be set to allow this. Please refer to "Im-
age source selection modes", page 28 to do this.
About input signals
The available input signals for your display are:
DisplayPort 1
The input corresponding to the DisplayPort 1
connector.
The input corresponding to the DVI 1 connector.
DVI 1
DisplayPort 2
The input corresponding to the DisplayPort 2
connector.
The input corresponding to the DVI 2 connector.
DVI 2
Automatic Selection
The input is automatically selected.
28
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
To manually select a video input signal:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Image Sources > (Left/Right) Image Source menu.
3. Enter the Input Signal submenu.
4. Select one of the available input signals and confirm.
5.24 Video encoding modes
Your Coronis Fusion 6MP display automatically detects the connected video input sig-
nals and applies the correct video encoding settings. Manually selecting a video encod-
ing mode is possible, but then your display’s image source selection mode should be
About video encoding modes
Video encoding modes specify how the color and luminance information is encoded in the video signal. In
consumer displays, this is usually done by a limited 8-bit encoding mechanism. Your Coronis Fusion 6MP
however, features 10-bit encoding enabling it to better match the DICOM defined grayscale range. Such
an extensive range is necessary to comply with the guidelines set forward by the latest medical guidelines.
The available video encoding modes for your display are listed below.
Please note that the display controller connected to your display might not always sup-
port all these video encoding modes.
Standard
HDR1
This mode uses the standard 8 bit encoding
mechanism.
This mode features 10-bit video encoding following
the High Dynamic Range (HDR) standard, usually
used on color displays.
HDR2
HDR2 is a Barco specific mode featuring 10-bit
video encoding following the High Dynamic Range
(HDR) standard but allowing full refresh rate (which
is not always possible with HDR1). This mode is
usually used on color displays.
Dual 10 (only with Barco display controller)
Automatic
Dual 10 is a Barco specific 10-bit video encoding
mode which is usually used on grayscale displays
and which allows full refresh rate.
When selecting this option, your Coronis Fusion
6MP will automatically assign the correct video
encoding settings to the connected video input
signals.
To manually select a video encoding mode:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Image Sources > (Left/Right) Image Source menu.
3. Enter the Video Encoding submenu.
4. Select one of the available video encoding modes and confirm.
K5902055 CORONIS FUSION 6MP 28/08/2013
29
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
5.25 Grayscale conversion modes
Your Coronis Fusion 6MP display automatically detects the connected video input
signals and applies the correct grayscale conversion settings. Manually selecting a
grayscale conversion mode is possible, but then your display’s image source selection
page 28 to do this.
About grayscale conversion modes
Grayscale conversion modes specify how color generated on the display controller is converted to
grayscale in your display.
The available grayscale conversion modes are:
No Conversion
Use Red Channel
Use Green Channel
Use Blue Channel
Use All Channels
This mode is intended for grayscale displays where
gray is sent over the red channel.
This mode is intended for grayscale displays where
gray is sent over the green channel.
This mode is intended for grayscale displays where
gray is sent over the blue channel.
This mode is intended for grayscale displays where
gray is sent over the red, green and blue channel.
This is done by means of a standard conversion
mechanism where 30% red, 59% green and 11%
blue are used to generate gray.
To manually select a grayscale conversion mode:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Image Sources > (Left/Right) Image Source menu.
3. Enter the Grayscale Conversion submenu.
4. Select one of the available color conversion modes and confirm.
5.26 EDID timings
Your Coronis Fusion 6MP display automatically detects the connected video input sig-
nals and applies the correct timings. Manually configuring the EDID timings is possible,
but then your display’s image source selection mode should be set to allow this. Please
About EDID timings
Following EDID timings are available for your Coronis Fusion 6MP:
Resolution
Allows to manually modify the resolution of the
image source video input signal.
Refresh Rate
Allows to manually select the refresh rate of the
image source video input signal depending on the
maximum refresh rate of the display controller
connected to your display.
Color Depth
Allows to change the color depth to 8 or to 10 bit.
30
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
To manually set EDID timings:
1. Bring up the OSD main menu.
2. Navigate to the Configuration > Image Sources > (Left/Right) Image Source menu.
3. Enter the Timings submenu.
4. Select Resolution, Refresh Rate or Color Depth.
5. Select one of the available settings and confirm.
5.27 Display info
About display info
Your display serial number, color type, native resolution, firmware versions, etc. are available in a dedi-
cated submenu of the OSD menu.
To retrieve info about your display:
1. Bring up the OSD main menu.
2. Navigate to the About this Display menu to make the information visible on the screen.
5.28 Display status
About display status
The Status submenu of the OSD menu provides info on the current status of your display (runtimes, tem-
peratures, etc.), the status of the connected image sources (video encoding mode, timings, etc.), the
current calibration status of your display (display function, luminance, ALC, etc.) and the status about
activated connections.
To retrieve the status of your display:
1. Bring up the OSD main menu.
2. Navigate to the Status menu.
3. Enter the Display, Image Sources, Calibration or Connectivity submenu as desired.
K5902055 CORONIS FUSION 6MP 28/08/2013
31
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Advanced operation
32
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Cleaning your display
6. CLEANING YOUR DISPLAY
6.1 Cleaning instructions
To clean the display
Clean the display using a sponge, cleaning cloth or soft tissue, lightly moistened with a recognized clean-
ing product for medical equipment. Read and follow all label instructions on the cleaning product. In case
of doubt about a certain cleaning product, use plain water.
Do not use following products:
•
•
•
•
•
•
•
•
•
•
Alcohol/solvents at higher concentration > 5%
Strong alkalis lye, strong solvents
Acid
Detergents with fluoride
Detergents with ammonia
Detergents with abrasives
Steel wool
Sponge with abrasives
Steel blades
Cloth with steel thread
CAUTION: Take care not to damage or scratch the front glass or LCD. Be careful with
rings or other jewelry and do not apply excessive pressure on the front glass or LCD.
CAUTION: Do not apply or spray liquid directly to the display as excess liquid may cause
damage to internal electronics. Instead, apply the liquid to a cleaning cloth.
K5902055 CORONIS FUSION 6MP 28/08/2013
33
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Cleaning your display
34
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Repackaging instructions
Bottom buffer
Power supply
Display controller box
3
4
7
8
Cables (video, USB, power)
7.1 Repacking your display
How to repack your display
1. Place the empty box on a stable surface.
2. Slide the system CD and user guide in the dedicated bag attached at the inside of the box.
3. Place the bottom buffer in the box.
4. Put the power supply in the dedicated cavity of the bottom buffer.
5. Put the Coronis Fusion 6MP display in its original bag and place it in the box with its panel facing
downwards.
6. Put the top buffer on top of the display.
7. When applicable, slide the display controller box in the dedicated cavity of the buffers.
8. Put all cables (video, USB, power) in their original bag and slide them in the dedicated cavity of the
buffers.
9. Close and seal the box.
36
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
8. IMPORTANT INFORMATION
8.1 Safety information
General recommendations
Read the safety and operating instructions before operating the device.
Retain safety and operating instructions for future reference.
Adhere to all warnings on the device and in the operating instructions manual.
Follow all instructions for operation and use.
Electrical Shock
•
•
Do not modify this equipment without authorization of the manufacturer.
No user-serviceable part inside. The equipment should be opened only by qualified service personnel.
Type of protection (electrical):
Display with external power supply: Class I equipment.
Degree of safety (flammable anesthetic mixture):
Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen
or nitrous oxide.
Non-patient care equipment
•
Equipment primarily for use in a health care facility that is intended for use where contact with a patient
is unlikely (no applied part).
•
•
The equipment may not be used with life support equipment.
The user should not touch the equipment, nor its signal input/output ports and the patient at the same
time.
Power connection – Equipment with external 24 VDC power supply
•
Power requirements: The equipment must be powered using the delivered medical approved 24 VDC
) SELV power supply.
The medical approved DC (
(
•
•
) power supply must be powered by the AC mains voltage.
The power supply is specified as a part of the ME equipment or combination is specified as a ME
system.
•
To avoid the risk of electric shock, this equipment must only be connected to a supply mains with
protective earth.
•
•
The equipment should be installed near an easily accessible outlet.
The equipment is intended for continuous operation.
K5902055 CORONIS FUSION 6MP 28/08/2013
37
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
Transient over-voltage
If the device is not used for a long time, disconnect it from the AC inlet to avoid damage by transient
over-voltage.
To fully disengage the power to the device, please disconnect the power cord from the AC inlet.
Power cords:
•
Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 AWG min., rated 250 V
min., provided with a hospital-grade type plug 5-15P configuration for 120V application, or 6-15P for
240V application.
•
•
Do not overload wall outlets and extension cords as this may result in fire or electric shock.
Mains lead protection (U.S.: Power cord): Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them, paying particular attention to cords
at plugs and receptacles.
•
The power supply cord should be replaced by the designated operator only at all time.
Water and moisture
Never expose the device to rain or moisture.
Never use the device near water - e.g. near a bathtub, washbasin, swimming pool, kitchen sink, laundry
tub or in a wet basement.
Ventilation
Do not cover or block any ventilation openings in the cover of the set. When installing the device in a
cupboard or another closed location, heed the necessary space between the set and the sides of the
cupboard.
Installation
Place the device on a flat, solid and stable surface that can support the weight of at least 3 devices. If you
use an unstable cart or stand, the device may fall, causing serious injury to a child or adult, and serious
damage to the device.
This apparatus conforms to:
CE0120 (MDD 93/42/EEC; A1:2007/47/EC class IIb product), CE - 2004/108/EC, IEC 60950-1:2005
+ A1:2009 (2ND EDITION), IEC 60601-1:2005, ANSI/AAMI ES 60601-1:2005 + C1:2009 + A2:2010,
CAN/CSA C22.2 No. 60601-1 (2008), DEMKO - EN 60601-1:2006, EN 60601-1-2:2007, CCC -
GB9254-2008 + GB4943.1-2011 + GB17625.1-2012, KCC, VCCI, FCC class B, ICES-001 Level B, FDA
510(k), RoHS.
National Scandinavian Deviations for CL. 1.7.2:
Finland: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan"
Norway: "Apparatet må tilkoples jordet stikkontakt"
Sweden: "Apparaten skall anslutas till jordat uttag"
8.2 Environmental information
Disposal information (Waste Electrical and Electronic Equipment)
This symbol on the device indicates that, under European Directive 2002/96/EC governing waste
from electrical and electronic equipment, this device must not be disposed of with other municipal waste.
38
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
Please dispose of your waste device by handing it over to a designated collection point for the recycling of
waste electrical and electronic equipment. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, please separate these devices from other types of waste and recycle
them responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this device, please contact your local city office or your municipal
waste disposal service. For details, please visit the Barco website at: http://www.barco.com/en/About-
Barco/weee.
Turkey RoHS compliance
Republic of Turkey: In conformity with the EEE Regulation
Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur
中国大陆 RoHS
Chinese Mainland RoHS
根据中国大陆《电子信息产品污染控制管理办法》（也称为中国大陆RoHS）， 以下部分列出了Barco产品
中可能包含的有毒和/或有害物质的名称和含量。中国大陆RoHS指令包含在中国信息产业部MCV标准：
“电子信息产品中有毒物质的限量要求”中。
According to the “China Administration on Control of Pollution Caused by Electronic Information Products”
(Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or
hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in
the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of
toxic substances in Electronic Information Products”.
零件项目(名称)
有毒有害物质或元素
Component name
Hazardous substances and elements
汞
铅
镉
六价铬
多溴联苯 多溴二苯
醚
Hg
Pb
Cd
Cr6+
PBB
PBDE
x
x
x
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
印制电路配件
Printed Circuit Assemblies
液晶面板
o
o
o
o
o
LCD panel
外接电(线)缆
External Cables
內部线路
Internal wiring
金属外壳
Metal enclosure
塑胶外壳
Plastic enclosure
o
x
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
散热片(器)
Heatsinks
电源供应器
Power Supply Unit
风扇
Fan
K5902055 CORONIS FUSION 6MP 28/08/2013
39
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
零件项目(名称)
有毒有害物质或元素
Component name
Hazardous substances and elements
汞
铅
镉
六价铬
多溴联苯 多溴二苯
醚
Hg
Pb
Cd
Cr6+
PBB
PBDE
o
o
o
o
o
o
o
o
o
o
文件说明书
Paper Manuals
光盘说明书
o
o
CD manual
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下.
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for
this part is below the limit requirement in SJ/T11363-2006.
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的
限量要求.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous
materials used for this part is above the limit requirement in SJ/T11363-2006
在中国大陆销售的相应电子信息产品（EIP）都必须遵照中国大陆《电子信息产品污染控制标识要求》标准
贴上环保使用期限（EFUP）标签。Barco产品所采用的EFUP标签（请参阅实例，徽标内部的编号使用于制
定产品）基于中国大陆的《电子信息产品环保使用期限通则》标准。
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the
“Electronic Information Products Pollution Control Labeling Standard” of Chinese Mainland, marked with
the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses
(please refer to the photo) is based on the “Standard of Electronic Information Products Environmental
Friendly Use Period” of Chinese Mainland.
10
8.3 Regulatory compliance information
Indications for use
The Coronis Fusion 6MP (MDCC-6230) display is a display device capable of displaying two 3MP display
images electronically fused together on the one panel. It is intended to be used in displaying and viewing
digital images for review and analysis by trained medical practitioners. It provides a screen resolution
of 3280 x 2048 pixels at a pixel pitch of 0.1995mm. This provides the equivalent resolution of 2 x 3MP
displays.
The Coronis Fusion 6MP (MDCC-6230) display is not intended for primary diagnosis of Mammography
images.
Caution (USA): Federal law restricts this device to sale by or on the order of a physician or a practitioner
trained on its use.
40
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
FCC class B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television reception, which can be
determined by turning the device off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Canadian notice
This ISM device complies with Canadian ICES-001.
Cet appareil ISM est conforme à la norme NMB-001 du Canada.
8.4 EMC notice
General information
No specific requirement on the use of external cables or other accessories except power supply.
With the installation of the device, use only the delivered power supply or a spare part provided by the
legal manufacturer. Using another can result in a decrease of the immunity level of the device.
Electromagnetic emissions
The Coronis Fusion 6MP is intended for use in the electromagnetic environment specified below. The
customer or the user of the Coronis Fusion 6MP should assure that it is used in such an environment.
Emissions test
Compliance
Electromagnetic environment –
Guidance
RF emissions
CISPR 11
Group 1
The Coronis Fusion 6MP uses
RF energy only for its internal
function. Therefore, its RF
emissions are very low and are
not likely to cause any interference
in nearby electronic equipment.
The Coronis Fusion 6MP
RF emissions
Class B
Class D
Complies
is suitable for use in all
establishments, including
CISPR 11
Harmonic emissions
domestic establishments and
those directly connected to the
public low-voltage power supply
network that supplies buildings
used for domestic purposes.
IEC 61000-3-2
Voltage fluctuations/ flicker
emissions
IEC 61000-3-3
This Coronis Fusion 6MP complies with appropriate medical EMC standards on emissions to, and inter-
ference from surrounding equipment. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
K5902055 CORONIS FUSION 6MP 28/08/2013
41
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
Interference can be determined by turning the equipment off and on.
If this equipment does cause harmful interference to, or suffer from harmful interference of, surrounding
equipment, the user is encouraged to try to correct the interference by one or more of the following mea-
sures:
•
•
•
•
Reorient or relocate the receiving antenna or equipment.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced technician for help.
Electromagnetic immunity
The Coronis Fusion 6MP is intended for use in the electromagnetic environment specified below. The
customer or the user of the Coronis Fusion 6MP should assure that it is used in such an environment.
Immunity test
IEC 60601
Test levels
Compliance level
Electromagnetic
environment –
guidance
Electrostatic discharge ± 6kV contact
± 6kV contact
± 8kV air
Floors should be wood,
concrete or ceramic tile.
If floors are covered with
synthetic material, the
relative humidity should
be at least 30%
(ESD)
± 8kV air
IEC 61000-4-2
Electrical fast
transient/burst
± 2kV for power supply ± 2kV for power supply Mains power quality
lines
lines
should be that of a typical
commercial or hospital
environment
IEC 61000-4-4
± 1kV for input/ output
lines
± 1 kV line(s) to line(s)
± 1kV for input/ output
lines
± 1 kV line(s) to line(s)
Surge
Mains power quality
should be that of a typical
commercial or hospital
environment
IEC61000-4-5
± 2 kV line(s) to earth
± 2 kV line(s) to earth
Voltage dips, short
< 5% UT 1(> 95% dip in < 5% UT (> 95% dip in Mains power quality
interruptions and voltage UT) for 0.5 cycle
variations on power
UT) for 0.5 cycle
should by that of a typical
commercial or hospital
environment. If the user
of the Coronis Fusion
40% UT (60% dip in UT) 40% UT (60% dip in UT)
supply input lines
for 5 cycles
for 5 cycles
IEC 61000-4-11
70% UT (30% dip in UT) 70% UT (30% dip in UT) 6MP requires continued
for 25 cycles
for 25 cycles
operation during power
mains interruptions, it
is recommended that
the Coronis Fusion 6MP
be powered from an
uninterruptible power
supply or a battery.
< 5% UT (>95% dip in
UT) for 5s
< 5% UT (>95% dip in
UT) for 5s
1. is the a.c. mains voltage prior to application of the test level.
42
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
Immunity test
IEC 60601
Test levels
Compliance level
Electromagnetic
environment –
guidance
Power frequency (50/60 3 A/m
Not applicable
Power frequency
Hz) magnetic field
magnetic fields should
be at levels characteristic
of a typical location in
a typical commercial or
hospital environment.
Portable and mobile
RF communications
equipment should be
used no closer to any
part of the Coronis Fusion
6MP, including cables,
than the recommended
separation distance
calculated from the
equation applicable
to the frequency
IEC 61000-4-8
Conducted RF
IEC 61000-4-6
Radiated RF
3 Vrms
3 V
150 kHz to 80 MHz
3 V/m
3 V/m
IEC 61000-4-3
80 MHz to 2.5 GHz
of the transmitter.
Recommended
separation distance
d = 1.2√P
d = 1.2√P 80 MHz to 800
MHz
d = 2.3√P 800 MHz to 2.5
Ghz
Where P is the maximum
output power rating
of the transmitter in
watts (W) according
to the transmitter
manufacturer and d
is the recommended
separation distance in
meters (m).
Field strengths from
fixed RF transmitters,
as determined by an
electromagnetic site
survey,2 should be less
than the compliance
level in each frequency
range.3
Interference may occur in
the vicinity of equipment
marked with symbol:
K5902055 CORONIS FUSION 6MP 28/08/2013
43
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
Immunity test
IEC 60601
Test levels
Compliance level
Electromagnetic
environment –
guidance
At 80 MHz and 800 MHz, the higher frequency range applies.
These guidelines may not apply in all situations. Electromagnetic propagation is af-
fected by absorption and reflection from structures, objects and people.
Recommended separation distance
The Coronis Fusion 6MP is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer of the user of the Coronis Fusion 6MP can help prevent elec-
tromagnetic interference by maintaining a minimum distance between portable and mobile RF communi-
cations equipment (transmitters) and the Coronis Fusion 6MP as recommended below, according to the
maximum output power of the communications equipment.
Rated maximum output Separation distance according to frequency of transmitter
power of transmitter 4
150kHz to 80MHz
80MHz to 800MHz
800MHz to 2.5GHz
W
d=1.2√P
d=1.2√P
d=2.3√P
0.01
0.1
1
0.12
0.12
0.23
0.38
1.2
3.8
12
0.38
1.2
3.8
12
0.73
2.3
7.3
23
10
100
At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
These guidelines may not apply in all situations. Electromagnetic propagation is af-
fected by absorption and reflection form structures, object and people.
2. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur
radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in
the location in which the Coronis Fusion 6MP is used exceeds the applicable RF compliance level above, the Coronis Fusion 6MP
should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as
re-orienting or relocating the Coronis Fusion 6MP.
3. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
4. For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be
estimated using the equation applicable to the frequency of the transmitter. Where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.
44
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
8.5 Explanation of symbols
Symbols on the device
On the device or power supply, you may find the following symbols (nonrestrictive list):
Indicates compliance with the Directive 93/42/EEC as Class I device
Indicates compliance with the Directive 93/42/EEC as Class II device
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL regulations
Indicates the device is approved according to the UL regulations for Canada
and US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
Indicates the device is approved according to the BSMI regulations
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the manufacturing date
Indicates the temperature limitations for the device to safely operate within specs
K5902055 CORONIS FUSION 6MP 28/08/2013
45
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
Indicates the device serial no.
Consult the operating instructions
Indicates this device must not be thrown in the trash but must be recycled,
according to the European WEEE (Waste Electrical and Electronic Equipment)
directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
8.6 Legal disclaimer
Disclaimer notice
Although every attempt has been made to achieve technical accuracy in this document, we assume no
responsibility for errors that may be found. Our goal is to provide you with the most accurate and usable
documentation possible; if you discover errors, please let us know.
Barco software products are the property of Barco. They are distributed under copyright by Barco N.V. or
Barco, Inc., for use only under the specific terms of a software license agreement between Barco N.V. or
Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any
form, is authorized.
The specifications of Barco products are subject to change without notice.
Trademarks
All trademarks and registered trademarks are property of their respective owners.
Copyright notice
This document is copyrighted. All rights are reserved. Neither this document, nor any part of it, may
be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including
photocopying, taping or information storage and retrieval systems - without written permission of Barco.
© 2013 Barco N.V. All rights reserved.
Patent information (EXAMPLE)
This product is covered under the following intellectual property rights:
US Patent RE43,707
US Patent 7,038,186
US Patent 7,166,829
US Patent 6,950,098
European Patent 1 274 066.
46
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
8.7 Technical specifications
Overview
Product acronym
MDCC-6230
Screen technology
TFT AM Color LCD Dual Domain IPS-Pro
Active screen size (diagonal) 772 mm (30.4")
Active screen size (H x V)
Aspect ratio (H:V)
Resolution
654 x 409 mm (25.8 x 16.1")
16:10
native 6MP (3280 x 2048)
configurable to 2 x 3MP+ (1640 X 2048)
configurable to 2 x 3MP (1536 X 2048)
Pixel pitch
0.1995 mm
Color imaging
Gray imaging
Color support
Viewing angle (H, V)
Yes
Yes
30 bit
178°
Uniform Luminance
Technology (ULT)
Yes
Per Pixel Uniformity (PPU)
No
Ambient Light Compensation Yes
(ALC)
Backlight Output Stabilization Yes (2x)
(BLOS)
I-Guard
Yes
Maximum luminance
720 cd/m²
DICOM calibrated luminance 500 cd/m²
(ULT off)
Contrast ratio (typical)
Response time (Tr + Tf)
Scanning frequency (H; V)
Housing color
1000:1 (panel typical)
18 ms
30-150 kHz; 15-80 Hz
Black / Silver
Video input signals
Video inout terminals
USB ports
DVI-D Dual Link (2x), DisplayPort (2x)
NA
1 upstream (endpoint), 3 downstream
2.0
USB standard
Power requirements (nominal) 100-240V
Power consumption (nominal) 125W
Power save mode
Power management
Dot clock
Yes
DVI-DMPM, DP-DMPM
280 MHz
OSD languages
English, German, French, Dutch, Spanish, Italian, Portugese, Polish,
Russian, Swedish, Chinese (simplified), Japanese, Korean, Arabic
Dimensions with stand (W x H Portrait: NA Landscape: 731 x 580~676 x 265 mm
x D)
Dimensions w/o stand (W x H Portrait: NA Landscape: 731 x 485 x 141 mm
x D)
Dimensions packaged (W x H 869 x 764 x 400 mm
x D)
Net weight with stand
26.5 kg
K5902055 CORONIS FUSION 6MP 28/08/2013
47
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
Net weight w/o stand
20 kg
Net weight packaged with
stand
36.5 kg
Net weight packaged w/o stand N/A
Height adjustment range
Tilt
96 mm
-5° / +25°
Swivel
-45° / +45°
Pivot
N/A
Mounting standard
Screen protection
Recommended modalities
Certifications
VESA (100 mm)
Protective, non-reflective glass cover
CT, MR, US, DR, CR, NM, Film
CE0120 (MDD 93/42/EEC; A1:2007/47/EC class IIb product), CE -
2004/108/EC, IEC 60950-1:2005 + A1:2009 (2ND EDITION), IEC
60601-1:2005, ANSI/AAMI ES 60601-1:2005 + C1:2009 + A2:2010,
CAN/CSA C22.2 No. 60601-1 (2008), DEMKO - EN 60601-1:2006,
EN 60601-1-2:2007, CCC - GB9254-2008 + GB4943.1-2011 +
GB17625.1-2012, KCC, VCCI, FCC class B, ICES-001 Level B, FDA
510(k), RoHS.
Supplied accessories
User Guide
Quick Installation Sheet
Video cables (2x DVI Dual Link, 2x DisplayPort)
Main cables (UK, European (CEBEC/KEMA), USA (UL/ CSA; adaptor
plug NEMA 5-15P), Chinese (CCC))
USB 2.0 cable
External power supply
Optional accessories
QA software
None
MediCal QAWeb
Units per pallet
NA
Pallet dimensions (W x H)
Warranty
NA
5 years
Operating temperature
Storage temperature
Operating humidity
Storage humidity
0°C to 35°C (15°C to 30°C within specs)
-20°C to 60°C
8% - 80% (non-condensing)
5% - 95% (non-condensing)
Operation altitude
3000 m
8.8 Open source license information
Open source license information
Open source license usage
This product contains software components released under an Open Source license. A copy of the source
code is available on request by contacting your Barco customer support representative.
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-
TION ARE PROVIDED "AS IS" WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-
LAR PURPOSE. IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTOR
BE LIABLE FOR DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE
48
K5902055 CORONIS FUSION 6MP 28/08/2013
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Important information
POSSIBILITY OF SUCH DAMAGES. MORE INFORMATION/DETAILS IS TO BE FOUND IN EACH SPE-
CIFIC OPEN SOURCE LICENSE.
Copyright on each Open Source Software component belongs to the respective initial copyright holder,
each additional contributor and/or their respective assignee(s), as may be identified in the respective doc-
umentation, source code, README file, or otherwise. You shall not remove or obscure or otherwise alter
the respective copyrights.
You acknowledge living up to the conditions of each separate Open Source Software license.
A list of the Open Source Software components used is available in the applicable EULA, through the
(customer section of the) Barco website or through other (online) means.
K5902055 CORONIS FUSION 6MP 28/08/2013
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
K5902055-01
August 2013
Barco n.v.
President Kennedypark 35
8500 Kortrijk
Belgium
0120
Download from Www.Somanuals.com. All Manuals Search And Download.
|