LAMINATOR
OPERATING PROCEDURES
CARE AND CLEANING
Be sure that the machine is placed on a flat surface. Plug the
power cord into a grounded AC outlet. To use your laminator
follow these directions:
Always unplug the laminator from electrical outlet before
cleaning. Clean the outside of the laminator with a damp
cloth only. Do not use solvents such as alcohol, benzene or
thinner. Do not immerse in water.
The QuikFinish 4-Roller laminator has HOT, COLD, and FOIL
laminating settings. The PLH4100 is designed for documents up to
10 inches wide. The PLH4150 is designed for documents up to 15
inches wide. This unit also includes a 1.5 hour AUTO-SHUTOFF
function.
Home/Office Laminator
To Cold laminate:
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or qualified service agent in
order to avoid a hazard to your health.
1. Push the switch to COLD position. The RED LIGHT will
illuminate, and the unit is ready to cold laminate.
2. Prepare the item to COLD laminate according to
instructions for cold laminate pouch.
3. Feed document to be COLD laminated into front of the
unit. It will be pulled into the laminator. Banner American
suggests using the pouch carrier.
IMPORTANT SAFETY INSTRUCTIONS
PRODUCT SPECIFICATIONS
Your safety as well as the safety of others is important to Banner
American Products, Inc. In this manual and on the product are
important safety instructions. PLEASE READ ALL SAFETY
INSTRUCTIONS CAREFULLY BEFORE OPERATING.
Power........................................ AC 115 V/60Hz (U.S.A.)
AC 220-240 V/50Hz (Europe)
Dimensions .............................. 17 3/4” x 7 3/4” x 4 1/2” (PLH4100)
Operating
Instructions
To Hot Laminate:
22” x 7 3/4” x 4 1/2” (PLH4150)
CAUTIONS
Before using your laminator, be sure to observe the
Maximum Thickness ................1/12” (2mm)
Film Thickness .........................4 mil up to 18 mil
Auto stop time .......................... 1.5 +/- 10% HOURS
Temperature range.................... 95 - 125 C(203 - 257 F)
1. Push the slide switch to LAMINATE position. The
temperature control knob will be available for adjustment,
you can select suitable temperature by turning knob to
laminate different pouch sizes. After approximately 3-5
minutes, the unit is warmed up and the GREEN READY
light will illuminate and the unit is ready to laminate.
Note: If you slide the switch from FOIL to LAMINATE
position, make sure to wait and laminate after 15 minutes.
2. Take one pouch and peel apart the pouch. Insert the
document into the laminating pouch.
3. Insert the pouch (closed end first) into the laminator until
the rollers catch the pouch and start to feed automatically.
4. Remove the pouch from rear of the laminator after it has
completely exited the laminator.
following precautions:
o not touch or place anything on hot
urfaces. Wait for unit to cool before moving
cleaning.
TEMPERATURE ADJUSTMENT USAGE:
1. Temperature adjustment is only available in the HOT
lamination mode. It is not available in COLD or FOIL mode.
2. Once the green laminate LED illuminates in the HOT
lamination mode, it will not distinguish even if you adjust the
temperature adjustment to a different temperature setting
unless you switch to the OFF position.
3. To change the laminating temperature, adjust the
temperature knob to desired temperature. Once you have
selected desired temperature, please wait for 2-3 minutes
before laminating.
2. To prevent electric shock do not
KEEP
DRY
immerse in or operate near water or
other liquids.
3. The use of other attachments is not
recommended by the manufacturer in
conjunction with the product. Use of other
attachments may cause injury.
STANDARD
To Hot Foil Laminate:
MODEL PLH4100 & PLH4150
1. Push the slide switch to the FOIL position. After
approximately 5 minutes, the GREEN READY light will
illuminate, and the unit is ready to foil.
2. Lay out the foil paper on the document according to foil
instructions. Insert the foiled item against the fold inside
the carrier. (A paper carrier must be used for foiling).
3. Insert the carrier (closed end first) into the laminator
unit until the rollers catch the carrier and start to feed
automatically.
4. Not all pouches can be used at the same temperature for
different thickness pouches. Please note that these settings
are SUGGESTIONS ONLY. You may need to test your
pouches under different temperatures to reach satisfactory
results.
4. This product is not intended for any
other use other than lamination.
LAMINATOR
ONLY
Before operating please read all
instructions.
5. For best results it is recommended
that only Banner American Products’
laminating pouches be used.
POUCHES
4. Remove the carrier from the rear of the laminator after it
has completely exited the laminator. Leave the document
inside the carrier for several seconds to cool before
removing it.
6. Always unplug the unit when not in use
to prevent accidents. The electrical outlet
should be installed near the equipment and
should be easily accessible.
To Turn the Laminator Off:
95-100 203-212
100-105 212-221
3 mil
5 mil
(75 micron)
(125 micron)
1. Push the switch to OFF position when you are finished
laminating or foiling your documents.
7. Do not operate with a damaged power
supply cord.
Note: The left temperature control knob is only available for
the LAMINATE position.
A d
AUTO-SHUTOFF TIME:
NO
HANDS
This unit will automatically shut-off after approximately 1.5
hours. To re-start the laminator, slide the switch to OFF
position for at least 5 seconds, then slide the switch to COLD,
LAMINATE or FOIL position. The unit will start to work again.
8. Keep loose clothing, fingers, hair, jewelry
and other foreign objects away from
laminating slot.
Download from Www.Somanuals.com. All Manuals Search And Download.
|