Gateway E-9220T Server
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1 Checking Out Your Gateway Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
System board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Gateway Web site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Setting Up Your Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting up the hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Protecting from power source problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Starting your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Understanding the power-on self-test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Turning off your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting up the operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Initial hardware settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Maintaining Your Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Caring for your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Preparing for system recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Recording the BIOS configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
System administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Gateway Server Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Server security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using Active Management Technology (AMT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Using your System Companion CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4 Installing Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Preparing to install components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Selecting a place to work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Gathering the tools you need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Preventing static electricity discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Accessing the internal components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Opening the server case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Removing the bezel assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Removing the processor air duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installing the processor air duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installing the bezel assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Closing the server case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
www.gateway.com
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing or replacing a fixed or removable-media drive . . . . . . . . . . . . . . . . . . . . . . . 39
Installing or replacing a hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Configuring your onboard RAID solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Configuring the onboard SATA RAID solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Installing memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Memory online sparing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Installing PCI expansion cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Replacing a fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Replacing the CMOS battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Replacing the system board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5 Using the BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Opening the BIOS Setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Updating the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Resetting BIOS passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Safety guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
First steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Beep codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
CD or DVD drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Diskette drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Expansion cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Modem (telephone dial-up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Telephone support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Before calling Gateway Customer Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Telephone support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Tutoring and training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
ii
www.gateway.com
Download from Www.Somanuals.com. All Manuals Search And Download.
A Server Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
System specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
System board specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Electronic specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Additional specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
B BIOS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
C Safety, Regulatory, and Legal Information . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
www.gateway.com
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
www.gateway.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Back
Back
Power supply modules
Cover release lever
Power supply LEDs
Power connector
Power connector
Power supply LEDs
Case cover thumbscrew
Power supply
module latch
Power supply
module latch
NIC (RJ-45)
USB ports
Serial port
Keyboard port
Mouse port
PCI slots
(shown with
EMI shields)
Card retention bar
Video port (on
PCI card)
www.gateway.com
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Checking Out Your Gateway Server
Interior
Cover release
latch
Power supply
modules
5.25-inch
drive bays
3.5-inch
drive bays
Memory
slots
Front fan
Battery
Back fan
Processor
air duct
Internal
3.5-inch
drive bays
www.gateway.com
4
Download from Www.Somanuals.com. All Manuals Search And Download.
System board
System board
Rear fan connector
Memory slots
Front fan
connector
Power
connector
CMOS Battery
NIC (RJ-45)
IDE connector
USB connectors
SATA connectors
USB connectors
Serial port
Keyboard and
mouse ports)
Main power
connector
PCIe slot 1 - x1
J3F3 jumper
PCIe slot 2 - x8
Diskette drive
connector
PCI slot 3 - 32-bit
PCIe slot 4 - x4
Power button
connector
PCI slot 5 - 32-bit
www.gateway.com
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Checking Out Your Gateway Server
Getting Help
In addition to your operating system’s documentation, you can use the following
information resources to help you use your server.
Gateway Web site
Gateway provides a variety of information on its Web site to help you use your server.
Visit the Gateway Web site at support.gateway.com for:
■
■
■
■
■
Technical documentation and product guides
Technical tips and support
Updated hardware drivers
Order status
Frequently asked questions (FAQs)
www.gateway.com
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Setting Up Your Server
Setting up the hardware
To make sure that your working environment is safe:
■
Use a clean, dry, flat, stable surface for your server. Allow at least 6 inches at the
back of the server for cabling and air circulation.
■
■
Use the instructions on your server’s setup poster to set up your hardware.
Use an uninterruptible power supply (UPS) with surge protection for protection
from power outages and power spikes.
Your server comes with a 3-wire AC power cords fitted with the correct
Warning
plug style for your region. If these plugs do not match the connector
on your UPS or wall outlet, do not attempt to modify the plugs in any
way. Use a UPS or wall outlet that is appropriate for the supplied
AC power cords.
■
■
Avoid subjecting your server to extreme temperature changes. Do not expose your
server to direct sunlight, heating ducts, or other heat-generating objects. Damage
caused by extreme temperatures is not covered by your warranty. As a general rule,
your server is safest at temperatures that are comfortable for you.
Keep your server and magnetic media away from equipment that generates
magnetic fields, such as unshielded stereo speakers. Strong magnetic fields can erase
data on both diskettes and hard drives. Even a telephone placed too close to the
server may cause interference.
www.gateway.com
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Protecting from power source problems
Protecting from power source problems
Line conditioners, and uninterruptible power supplies can help protect your server against
power source problems.
Line conditioners
A line conditioner protects your server from the small fluctuations in voltage from an
electrical supply. Most servers can handle this variation, called line noise, without problems.
However, some electrical sources include more line noise than normal. Line noise can also
be a problem if your server is located near, or shares a circuit with, a device that causes
electromagnetic interference, such as a television or a motor.
Some uninterruptible power supplies include simple line-conditioning capabilities.
Uninterruptible power supplies
Use an uninterruptible power supply (UPS) to protect your server from data loss during a
a power failure and lets you save your work and shut down your server. You cannot run
your server for an extended period of time while using only the UPS. Be sure to use a UPS
with surge protection. To buy a UPS, contact Gateway Customer Care, Gateway Sales, or
visit accessories.gateway.com. For more information on contacting Customer Care, see
“Telephone support” on page 86.
www.gateway.com
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Setting Up Your Server
Starting your server
Before you start your server for the first time:
■
Make sure that the server and monitor are plugged into a power outlet or UPS and
that the UPS (if you are using one) is turned on.
■
Make sure that all cables are connected securely to the correct ports and jacks on
the back of the server.
When you connect peripheral devices to the server, make sure that
your server and devices are turned off and the power cords are
unplugged.
Caution
To start the server:
1 Press the power button.
Power
button/power
indicator LED
When the power
It means...
indicator LED is...
Green
The server is turned on.
The server is turned off.
Low power state (S1 — S3)
Off
Slowly blinking
www.gateway.com
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting your server
If nothing happens when you press the power button:
■
Make sure that the UPS, if you are using one, is connected securely to an
electrical outlet, turned on, and working correctly.
■
Make sure that the monitor is connected to the server, plugged into the power
outlet or UPS, and turned on. You may also need to adjust the monitor’s
brightness and contrast controls.
2 The first time you turn on the server, any pre-installed operating system may begin
asking you for configuration settings. See your operating system’s documentation for
instructions on configuring advanced settings for your specific network.
Selecting the boot device
To select which device your server boots from:
1 During server startup, press F10. The Boot menu opens.
2 Select the device you want to boot from. Common choices include:
■
■
■
■
Removable Dev. (Removable device)
ATAPI CDROM (CD or DVD drive)
Hard Drive
IBA GE NIC (Network boot)
Understanding the power-on self-test
When you turn on your server, the power-on self-test (POST) routine checks the server
memory and components. If POST finds any problems, the server displays error messages.
Write down any error messages that you see, then see “Error messages” on page 73 and
“Beep codes” on page 76 for troubleshooting information.
www.gateway.com
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Setting Up Your Server
Turning off your server
Every time you turn off your server, first shut down the operating system. You may lose
data if you do not follow the correct procedure.
To turn off the server:
1 See the operating system’s documentation or online help for instructions on shutting
down the operating system. Whenever possible, you should use the operating system’s
shut down procedure instead of pressing the power button.
2 If your server did not turn off automatically, press the power button. If nothing
happens when you press the power button, press and hold it for five seconds and
the server will turn off.
The power button on the server does not turn off server AC power.
Warning
To remove AC power from the server, you must unplug both
AC power cords from the wall outlet or power source. The power
cords are considered the disconnect device to the main (AC) power.
If you routinely turn off your server (daily or weekly), do not unplug
the server or use the On/Off switch on the UPS. Regularly cutting
off all power to your server may cause the CMOS battery to fail
prematurely.
Caution
www.gateway.com
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the operating system
Setting up the operating system
If you ordered your server with the operating system already installed by Gateway, in most
cases it is completely installed and the basic settings are already configured. The Windows
Small Business Server operating system may require additional installation, depending on
the version you ordered. See your operating system’s documentation for instructions on
completing the installation or configuring advanced settings for your specific network.
If you are installing an operating system because it was not already installed by Gateway,
see the appropriate installation guide for instructions.
Initial hardware settings
Your server comes from the manufacturer with the correct initial hardware settings to
operate your server as configured. However, at some point you might want to change
settings to reflect a tasking change, a change in security requirements, or the addition of
new resources to your server.
General hardware settings, as well as the onboard RAID solution, can be changed by using
the BIOS Setup utility. Add-in RAID solutions must be configured using the specific RAID
console which accompanied that solution.
For information on the BIOS Setup utility, see “Using the BIOS Setup Utility” on page 65.
For information on BIOS settings, see “BIOS Settings” on page 95. For information on the
RAID BIOS Console utility, see “Configuring your onboard RAID solution” on page 42. For
information on a specific RAID console for an add-in RAID solution, see the documentation
on that hardware which accompanied your RAID solution.
www.gateway.com
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Setting Up Your Server
www.gateway.com
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Maintaining Your Server
Caring for your server
To extend the life of your server:
■
■
Be careful not to bump or drop your server.
When transporting your server, we recommend that you put it in the original
packaging materials.
■
■
Keep your server and magnetic media away from equipment that generates
magnetic fields.
Avoid subjecting your server to extreme temperatures. Do not expose your server
to heating ducts or other heat-generating objects. Damage caused by extreme
temperatures is not covered by your warranty. As a general rule, your server is safest
at temperatures that are comfortable for you.
■
■
Keep all liquids away from your server. When spilled onto server components,
almost any liquid can result in expensive repairs that are not covered under your
warranty.
Avoid dusty or dirty work environments. Dust and dirt can clog the internal
mechanisms and can cause the server to overheat.
Cleaning your server
Keeping your server clean and the vents free from dust helps keep your server performing
at its best. Your server cleaning kit could include:
■
■
■
■
■
■
■
A soft, lint-free cloth
Glass cleaner
An aerosol can of air with a narrow, straw-like extension
Isopropyl alcohol
Cotton swabs
A tape drive cleaning cartridge (if a tape drive is installed)
A CD or DVD drive cleaning kit
www.gateway.com
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for your server
Cleaning tips
■
Always turn off your server and other peripheral devices before cleaning any
components.
When you shut down your server, the power turns off, but some
Warning
electrical current still flows through your server. To avoid possible
injury from electrical shock, unplug the power cords and all other
cables connected to the server.
■
■
Use a damp, lint-free cloth to clean your server and other parts of your server
system. Do not use abrasive or solvent cleaners because they can damage the finish
on components.
Keep the cooling vents free of dust. With your server turned off and unplugged,
brush the dust away from the vents with a damp cloth, but be careful not to drip
any water into the vents.
Cleaning the keyboard
You should clean the keyboard occasionally by using an aerosol can of air with a narrow,
straw-like extension to remove dust and lint trapped under the keys.
If you spill liquid on the keyboard, turn off your server and turn the keyboard upside down
to let the liquid drain. Let the keyboard dry completely before trying to use it again. If
the keyboard does not work after it dries, you may need to replace it. Keyboard damage
resulting from spilled liquids is not covered by your warranty.
Cleaning the screen
If your computer screen is a flat panel display, use only a damp, soft cloth to clean it.
Never spray water directly onto the screen.
The flat panel display screens are made of specially coated glass and
can be scratched or damaged by abrasive or ammonia-based glass
cleaners.
Caution
- OR -
If your computer screen is not a flat panel display, use a soft cloth dampened with glass
cleaner to clean the screen. Never spray cleaner directly onto the screen.
Cleaning the tape drive
If you use a tape drive to back up your files, regular maintenance will lengthen the life
of the drive. To maintain the drive’s reliability:
■
■
Clean the drive monthly with the cleaning cartridge included with the drive.
Remove the tape from the drive whenever the drive is not in use.
www.gateway.com
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Maintaining Your Server
Preparing for system recovery
If your system files are corrupted, you may not be able to start the server from the hard
drive. Startup diskettes are diskettes that let you start the server and attempt to fix the
problem. See your operating system’s documentation or online help for instructions on
creating startup diskettes.
Some operating systems also let you create an emergency repair diskette to back up critical
operating system files. See your operating system’s documentation or online help for
instructions on using an emergency repair diskette.
Recording the BIOS configuration
working.
To record your BIOS configuration:
1 Print the appendix for BIOS Settings in this guide.
2 Restart your server, then press F2 when the Gateway logo screen appears during
startup. The BIOS Setup utility opens.
3 Record the BIOS settings on your printout.
www.gateway.com
18
Download from Www.Somanuals.com. All Manuals Search And Download.
System administration
System administration
Gateway Server Manager
Gateway Server Manager lets you manage multiple computers on a Windows network from
a single window, then implement commands and policies across the network with a single
action. With Gateway Server Manager, you can run system management tasks which are
triggered by certain events or conditions.
Printed documentation comes with the Gateway Server Manager CD. You can find additional
documentation in the program’s online help.
Server security
To prevent unauthorized use of the server, you can set BIOS startup passwords.
Using BIOS security passwords
Set up a supervisor password to prevent unauthorized access to the BIOS Setup utility. After
you create a supervisor password, you can set up a user password to prevent unauthorized
■
■
Enter either password to finish starting the server.
Enter the supervisor password to access the BIOS Setup utility.
For information about resetting BIOS passwords, see “Resetting BIOS passwords” on
page 69.
To set the BIOS security passwords:
1 Restart your server, then press F2 when the Gateway logo screen appears during
startup. The BIOS Setup utility opens.
2 Select the Security menu.
www.gateway.com
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Maintaining Your Server
3 Select the password to set according to the following table.
Option
Description
Supervisor password
To control access to system configuration, set a supervisor password.
Using a supervisor password lets you make changes to any setting
in the BIOS.
Passwords can be cleared. To clear the passwords, see “Resetting
BIOS passwords” on page 69.
User password
The supervisor password must be set up before a user password can
be set. To control access to the server, set a user password. The
supervisor can set the level of access granted to the user password.
■
No Access. User cannot access the BIOS Setup utility.
Limited. User can change only the date and time.
View Only. User can see all settings, but cannot change them.
Full. User can change every setting except the supervisor password.
■
■
■
Passwords can be cleared. To clear the passwords, see “Resetting
BIOS passwords” on page 69.
4 Type the password and press ENTER, then type it again and press ENTER.
5 Save your changes and exit the BIOS Setup utility.
www.gateway.com
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating a DOS-bootable System Update Package (SUP) CD
Creating a DOS-bootable System Update
Package (SUP) CD
Several utilities available on this server require that you boot the server to DOS. A
DOS-bootable System Update Package (SUP) CD, containing the update files, provides a
convenient way to accomplish this.
For this process, you will need:
■
■
■
A CD burner drive
CD burning software
A blank CD
To create a DOS-bootable SUP CD:
1 Put a blank CD into your CD burner.
2 Log on to your Internet connection.
3 Go to support.gateway.com.
4 Click Downloads, then Browse all downloads.
5 Select Servers for Step 1.
6 Select E-9220T for Step 2.
7 Select your operating system for Step 3.
8 Select BIOS downloads for Step 4.
9 Click Display results for Step 5.
10 Select the System Update Package file from the list of available files.
11 Click Download now, then select a convenient and easily found location for the file.
12 After the file downloads, find the .ISO file on your hard drive and double-click. Your
CD burner software will open.
CD burning software must be installed on your system for this process
to work.
Important
13 Click to start writing to the CD. The CD created will be DOS-bootable and will contain
the latest updates for BIOS, CMOS, and so on.
www.gateway.com
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Maintaining Your Server
Booting from the SUP CD:
startup. The BIOS Setup utility opens.
2 Select the Boot menu, then press ENTER. The Boot menu opens.
3 Select the CD drive on the Boot menu, then press ENTER. The server will now boot
to the CD drive. If the CD drive is not detected, see “CD or DVD drive” on page 79.
4 Insert the bootable CD into the CD drive.
5 Exit the BIOS Setup utility and let the server continue to boot.
6 After the updates are completed, restart your server, then press F2 when the Gateway
logo screen appears during startup. The BIOS Setup utility opens.
7 Use the down arrow key to select the Boot menu, then press ENTER. The Boot menu
opens.
8 Select your normal boot drive from the list, then press ENTER. The server will now
boot normally.
www.gateway.com
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Active Management Technology (AMT)
Using Active Management Technology
(AMT)
Active Management Technology (AMT) provides the following:
■
OOB System Management—Allows remote management of platforms, regardless
of power on/off or OS state.
■
Remote Troubleshooting and Recovery—Significantly reduces desk-side visits,
increasing the efficiency of IT technical staff.
■
■
Proactive Alerting—Decreases downtime and minimizes time-to-repair.
Remote Hardware and Software Tracking—Eliminates manual inventory tracking
and human error, reducing asset accounting costs and increasing tracking accuracy.
■
■
Non-Volatile Storage—Survives power outages and system rebuilds.
Tamper-Resistant Agents—Prevent users from removing critical inventory,
remote-control, or virus-protection agents.
To enable Active Management Technology (AMT):
The AMT network interface is disabled by default. If you do not
perform the following steps, AMT will not be available on your local
network.
Important
1 Start your server, then press F2 to enter the BIOS Setup utility.
2 Click Advanced to go to the Advanced menu, then click Management Configuration.
3 Enable Enter AMT BX Setup, then save and exit the BIOS Setup utility. The next time
your server is rebooted, the AMT console will open.
To configure and access Active Management Technology (AMT):
1 Log in to the AMT console by entering the default password “admin”.
2 Select Option 3 – TCP/IP.
3 When you are asked if you want to “Disable Network Interface – Y/N,” select No.
www.gateway.com
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Maintaining Your Server
4 When you are asked if you want the “DHCP Enabled – Y/N,” enter the response that
is appropriate to your situation.
If you enter No, then enter:
■
■
■
■
■
■
A Static IP Address for the AMT interface (Example: 10.225.200.101)
The Subnet Mask (Example: 255.255.255.0)
The Default Gateway (Example: 10.225.200.1)
The Preferred DNS Server (Example: 10.225.200.254)
The Alternate DNS Server (Example: 10.225.200.253)
The Domain Name (Example: irveng.local)
5 Press ESC to exit, then select Yes to confirm.
6 From another computer on your local network, open your Web browser.
7 Type the IP Address of AMT Interface (the IP address you entered in Step 4, plus port
16992. (For example: http://10.225.200.101:16992). A login prompt will appear.
8 Enter the following at the login prompt:
■
Default Username – admin
Default Password – admin
■
You are now logged in to the AMT Interface on your server and the following screen
opens.
www.gateway.com
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Active Management Technology (AMT)
From this initial screen you have access to the following information for the computer
you are currently using:
■
■
■
■
■
■
■
System Information
Processor Information
Memory Information
Disk Information
Event Log
Remote
Network Configuration
You can also change Network Settings and manage User Accounts.
9 To exit the AMT Interface, press ESC, then press Y to confirm.
www.gateway.com
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Maintaining Your Server
Using your System Companion CD
You can use your System Companion CD to:
■
■
■
Install hardware drivers
Install programs
View server documentation
Instructions for using the CD are provided in Using Your System Companion CD, a booklet
which is included with the CD.
www.gateway.com
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Installing Components
• Opening and closing the server case
• Installing and replacing major components
You must open your server case to install
components. If you are not comfortable with these
procedures, get help from a more experienced
computer user or computer service technician, or
contact Gateway Customer Care.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
Preparing to install components
Selecting a place to work
Work on your server in an area that:
■
■
■
■
■
Is clean (avoid dusty areas)
Is a low-static environment (avoid carpeted areas)
Has a stable surface on which to set your server
Has enough room to place all of your server parts
Is near a grounded outlet so you can test your server after installation
■ Is near a telephone (in case you need help from Gateway Customer Care). The
telephone must be directly connected to a telephone jack and cannot be connected
to your server.
Gathering the tools you need
Some tools and supplies that you may need to work on your server are:
■
■
■
■
A notebook to take notes
A Phillips screwdriver
A small flat-blade screwdriver
Small containers to store various types of screws
■ A grounding wrist strap (available at most electronic stores)
www.gateway.com
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Preventing static electricity discharge
Preventing static electricity discharge
The components inside your server are extremely sensitive to static electricity, also known
as electrostatic discharge (ESD).
To avoid exposure to dangerous electrical voltages and moving parts,
turn off your server and unplug the power cords and modem cable
before opening the server case.
Warning
Caution
ESD can permanently damage electrostatic discharge-sensitive
components in the server. Prevent ESD damage by following ESD
guidelines every time you open the server case.
Before working with server components, follow these guidelines:
■
■
■
Turn off the server, then unplug the power cords and all other cables.
Press the power button to drain any residual power from the server.
Wear a grounding wrist strap (available at most electronics stores) and attach it to
a bare metal part of the server. You can also touch a bare metal surface on the back
of the server with your finger.
To prevent risk of electric shock, do not insert any object into the vent
holes of the power supply module.
Warning
■
■
■
Avoid static-causing surfaces such as carpeted floors, plastic, and packing foam.
Avoid working on the server when your work area is extremely humid.
Remove components from their antistatic bags only when you are ready to use
them. Do not lay components on the outside of antistatic bags because only the
inside of the bags provide electrostatic protection.
■ Always hold expansion cards by their edges or their metal mounting brackets.
Avoid touching the edge connectors and components on the cards. Never slide
expansion cards or components over any surface.
www.gateway.com
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
Accessing the internal components
Opening the server case
Because the components inside your server are extremely sensitive to static electricity, make
sure that you follow the instructions at the beginning of this chapter to avoid static
electricity damage.
For correct cooling and air flow, always reinstall the side panel and
the air duct (if included) before you turn on the server. Operating the
server without the cover in place can damage server components.
Caution
To open the server case:
1 Follow the instructions in “Preventing static electricity discharge” on page 29.
2 Turn off the server, then unplug the power cords and all other cables connected to
the server.
This server may have two power cords. To disconnect internal
AC power, you must unplug both power cords.
Warning
3 Remove the case cover thumbscrew.
4 Lift the cover release lever.
www.gateway.com
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing the internal components
5 Swing the side panel away from the computer.
6 Lift the panel away from the server and place it out of the way.
www.gateway.com
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
Removing the bezel assembly
To remove the bezel assembly:
1 Follow the instructions in “Opening the server case” on page 30.
2 After removing the side panel, press the three black plastic tabs (positions indicated
by the arrows) to release the right side of the bezel.
3 Swing the right side of the bezel out until the left side of the bezel can be disengaged
from the left side of the computer, then remove the bezel.
www.gateway.com
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the processor air duct
To remove the processor air duct:
1 Follow the instructions in “Preventing static electricity discharge” on page 29.
2 Follow the instructions in “Opening the server case” on page 30.
3 Remove the cables from the air duct cable clip.
4 Grasp the air duct handle and remove the processor air duct from the chassis.
Air duct
handle
Processor air
duct
www.gateway.com
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
Installing the processor air duct
To install the processor air duct:
1 Align the left side of the processor air duct with the front fan and engage the
installation tabs on the bottom of the air duct with the installation holes in the side
of the chassis.
Be careful not to snag or unplug the fan cable when you install the
processor air duct.
Important
Processor air
duct installation
tabs
Processor air
duct installation
holes
www.gateway.com
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing the internal components
2 Press the processor air duct into place.
3 Place the diskette cable and hard drive power cable behind the cable clip on the
processor air duct.
www.gateway.com
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
Installing the bezel assembly
To install the bezel assembly:
If you have installed any new drives in the external drive bays, make
sure to remove the corresponding filler panels in the bezel before
installing it.
Important
1 Engage the tabs on the left side of the bezel with the slots in the left side of the
computer.
2 Swing the right side of the bezel in to engage the tabs on the right side of the bezel
with the slots on the right side of the computer.
3 Press the right side of the bezel firmly until it snaps into place.
www.gateway.com
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing the internal components
Closing the server case
To close the server case:
1 Make sure that all of the internal cables are arranged inside the case so they will not
be pinched when you close the case.
2 Align the panel tabs into the bottom case notches, then swing the side panel toward
the top of the computer to secure it into place.
3 Replace the case cover thumbscrew.
4 Reconnect the power cords and all other cables.
www.gateway.com
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
Installing drives
Your server’s basic configuration includes one CD or DVD drive and one 3.5-inch diskette
drive. Your server also has an additional 5.25-inch drive bay and an additional 3.5-inch
drive bay.
Your server can have as many as four SATA (standard) or SCSI (optional) drives in three
internal drive bays and one external fixed drive bay (the bottom 3.5-inch bay).
CD or DVD drive
5.25-inch drive bay
3.5-inch floppy drive
3.5-inch external drive bay
As you prepare to install drives, remember:
■
Do not use the top 5.25-inch drive bay for drives which have electronic
components exposed on the top. Drive mounting rails at the top of the bay may
damage any exposed electronic components.
■
Before you install a drive, see the drive’s documentation for information on
configuring the drive, setting drive jumpers, and attaching cables.
www.gateway.com
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing drives
■
IDE drives can be configured as master, slave, or cable-select.
■
If cable-select is available (drive assignments will be marked on the cable), the
IDE cable assigns the master/slave positions to the drives it connects. You can
override these assignments using the jumpers on the drives.
■
If cable-select is not available and only one drive is attached to an IDE controller
cable, configure the drive as master if it is a CD or DVD drive. If two drives of
any type are attached to the cable, configure one as master and one as slave.
■ You may need to configure the drives you install using the BIOS Setup utility. Press
F2 at startup to open the BIOS Setup utility.
Installing or replacing a fixed or removable-media drive
To install a drive in an external drive bay:
1 Follow the instructions in “Preventing static electricity discharge” on page 29.
2 Follow the instructions in “Opening the server case” on page 30.
3 If you are replacing a CD, DVD, or diskette drive, go to Step 6, otherwise follow the
instructions in “Removing the bezel assembly” on page 32.
4 If you are adding a new drive to an available drive bay, remove the EMI shield from
the bay by pulling the assembly out of the bay.
EMI shield
www.gateway.com
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
5 Slide the green drive retainer lever toward the back of the drive bay, then go to Step 8.
6 Disconnect the old drive’s cables from the back of the drive.
7 Slide the green drive retainer lever toward the back of the drive bay, then pull the
drive out of the bay.
Drive retainer
lever
8 Set any jumpers on the new drive. See the drive’s documentation for further
instructions.
9 Slide the new drive into the drive bay allowing it to protrude enough to line up with
the bezel when it is replaced, then push the green drive retainer lever toward the front
of the drive bay to lock the drive into place.
If you are installing a hard drive in the bottom, external 3.5-inch drive
bay, the green drive retainer lever will not slide forward to lock the
Important
drive into place. Instead, you must use a screw to secure the drive
in the bay.
When installing a CD, DVD, tape drive, or diskette drive, if the green
Tips & Tricks
drive retainer lever will not slide forward all the way to lock the drive
enough to lock the drive into place.
10 Connect the power and data cables.
11 Follow the instructions on “Installing the bezel assembly” on page 36.
12 Follow the instructions in “Closing the server case” on page 37.
www.gateway.com
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing drives
Use these instructions to install or replace a hard drive.
page 39.
Important
To install a hard drive in an internal drive bay:
1 Follow the instructions in “Preventing static electricity discharge” on page 29.
3 If you are replacing a drive, go to Step 4.
- OR -
If you are adding a new drive to an available drive bay, slide the green drive retainer
lever toward the front of the drive bay, then go to Step 7.
4 Disconnect the old drive’s cables from the front of the drive.
5 Slide the green drive retainer lever toward the front of the drive bay, then pull the
drive out of the bay.
Drive retainer
lever
6 Set any jumpers on the new drive. See the drive’s documentation for further
instructions.
www.gateway.com
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
7 Slide the new drive into the drive bay as far as it will go, then slide the green drive
retainer lever toward the back of the drive bay to lock the drive into the bay.
the drive into place, move the drive slightly, until the lever can be
moved back enough to lock the drive into place.
Tips & Tricks
8 Connect the power and data cables.
9 Follow the instructions in “Closing the server case” on page 37.
10 Format and partition the drive as necessary.
Configuring your onboard RAID solution
Your server comes equipped with an onboard chipset for a SATA RAID solution, which
supports RAID levels 0 (striping), 1 (mirroring), 5 (distributed data and parity), and 10
(RAID 0 + 1). You enable the onboard RAID solution in the BIOS (See SATA - page 98) and
configured by launching the appropriate RAID BIOS console during the boot process.
Configuring the onboard SATA RAID solution
Level Description and use
Pros
Cons
Numberof Fault
drives
Tolerant
0
1
Data divided into blocks and
High data
throughput for
large files.
No fault tolerance.
Data is lost if a drive
fails.
Oneortwo No
(on this
server)
distributed sequentially (pure
striping). Use for non-critical data
that requires high performance.
Data duplicated on another disk
(mirroring). Use for
read-intensive, fault-tolerant
systems.
100 percent
data
redundancy,
providing fault
tolerance.
More disk space
required. Reduces
usable disk space
to the size of the
smallest drive.
Reduced
Two
Yes
performanceduring
rebuilds.
www.gateway.com
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring your onboard RAID solution
Level Description and use
Pros
Cons
Numberof Fault
drives
Tolerant
5
Stripes data at a block level
Fast and
redundant
More disk space
required. Reduces
usable disk space
to 75% of total
storage in the disk
array.
Three
Yes
across several drives and
distributes parity among the
drives. No single disk is devoted
to parity.
10
A combination of RAID 1 and
RAID 0. Raid 0 is used for
performance, and RAID 1 is used
for fault tolerance.
Fast and
redundant
An additional drive
required.
Four
Yes
To launch the SATA RAID BIOS console:
1 Restart your server.
2 Press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility
opens.
3 From the Main BIOS menu, select the Advanced menu.
4 Select the Drive Configuration sub-menu.
5 For the Configure SATA as option, click RAID.
6 Exit the BIOS Setup utility.
7 Restart your server.
8 During the boot process you will see the following message:
Press <Ctrl>-<I> for BIOS Console
Press and hold the CTRL key, then press the I key. The RAID BIOS console will open.
When you press CTRL + I to configure the SATA RAID controller,
Important
the error message: Error (0146): Insufficient Memory to Shadow
PCI ROM may appear. This error message is produced because the
BIOS does not have sufficient memory to load the SATA RAID option
ROM into memory because other option ROMs are already loaded.
This is not a functional problem and can be disregarded. If you receive
this message, press F1 to continue.
9 Configure the RAID options, then exit the RAID BIOS console.
10 Reboot the server.
www.gateway.com
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
To configure the SATA RAID solution:
1 Open the BIOS Setup utility as described in the previous procedure.
2 Select Create RAID Volume from the Management menu.
3 Enter the name of the volume, or press ENTER to accept the default.
6 Set the capacity of the volume, then press ENTER to create the volume.
7 When you have defined the current volume, confirm your settings when prompted.
8 Repeat Step 2 through Step 7 to configure additional volumes.
9 Exit the RAID Configuration utility and reboot the server.
www.gateway.com
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing memory
Installing memory
When you upgrade your server memory, make sure that you install the correct type of
memory in your server. Your server supports from 256 MB to 8 GB total memory. Supported
DIMM sizes include 256 MB, 512 MB, 1 GB, and 2 GB.
Memory modules must be identical in each bank. Use only
DDR2-533 MHz, ECC unbuffered, 240-pin DIMM memory modules
in 256 MB, 512 MB, 1 GB, or 2 GB sizes.
Caution
Memory modules must be installed in pairs, to completely fill each
bank, and the banks must be filled in order. If you have memory
installed incorrectly, your server will not start up.
The BIOS configures the memory controller to run in either single channel or dual channel
mode, depending on the following:
■
If one or more fully populated DIMM banks are detected, the memory controller
will run in dual channel mode.
■
If only a single DIMM is present, the memory controller will run in single channel
mode.
DIMM banks must be populated using the following guidelines:
■
■
■
DIMM banks must be populated in order, starting with Bank 0.
Dual rank DIMMs must be populated before single rank DIMMs.
When using Dual Rank (double row) DIMMs, a maximum of four loads per memory
channel is supported, and therefore a maximum of four dual rank DIMMs can be
populated on this system board.
Channel B DIMM 1
Channel B DIMM 0
Channel A DIMM 1
Channel A DIMM 0
www.gateway.com
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
To install or replace memory:
1 Follow the instructions in “Preventing static electricity discharge” on page 29.
2 Follow the instructions in “Opening the server case” on page 30.
3 Pull the plastic tabs away from the sides of the memory module slot. If you are
replacing a memory module, remove the old module.
4 Align the notch on the new module with the notch in the memory module slot and
press the module firmly into the slot. The tabs on the sides of the memory slot should
secure the memory module automatically.
5 Follow the instructions in “Closing the server case” on page 37.
6 Restart your server and open the BIOS Setup utility. Verify the System Memory listed
in the Main menu. When you exit the BIOS Setup utility, make sure that the operating
system loads completely.
www.gateway.com
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing PCI expansion cards
Installing PCI expansion cards
Use the following chart to determine the PCI slot into which you should install your
expansion card.
This server does not have PCI hot-plug capability. Do not attempt to
install or remove a PCI card without turning off your server and
disconnecting it from the AC power source.
Caution
PCI slot Description
1
2
3
4
5
PCI Express - x1
PCI Express - x8
PCI - Runs at 32-bits
PCI Express - x4
PCI - Runs at 32-bits
PCI slot 1
PCI slot 2
PCI slot 3
PCI slot 4
To replace, add, or reseat a PCI expansion card:
1 Follow the instructions in “Preventing static electricity discharge” on page 29.
2 Follow the instructions in “Opening the server case” on page 30.
3 If you are replacing a card, disconnect any cables that are attached to the old card.
www.gateway.com
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
4 Loosen the captive thumbscrew on the card retention bar and swing the bar out from
the back of the chassis.
Card
retention bar
Captive
thumbscrew
5 If you are replacing a card, remove the old expansion card. To loosen the card you
can slightly rock the card end-to-end, but do not bend the card sideways.
Do not touch the contacts on the bottom part of the expansion card.
Touching the contacts can cause electrostatic damage to the card.
Caution
www.gateway.com
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing PCI expansion cards
6 Press the new card into the expansion slot. To help insert the card you can slightly
rock the card end-to-end, but do not bend the card sideways.
7 Swing the card retention bar back into place and tighten the captive thumbscrew.
Card
retention
bar.
Captive
thumbscrew
www.gateway.com
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
8 Connect any cables to the card. For more information, see the instructions in the card’s
documentation.
9 Follow the instructions in “Closing the server case” on page 37.
10 See the card’s documentation for software installation instructions.
www.gateway.com
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the processor
Replacing the processor
The server is compatible with Intel® Celeron (533 MHz FSB), Pentium 4 (800 MHz FSB),
and Pentium D (800 MHz FSB) processors with 256 KB (Celeron), 1 or 2 MB (Pentium 4),
or 2×1 MB (Pentium D), L2 caches. The server automatically detects the processors each
time you turn it on. Whenever you install new processors, you should first install the most
current version of the BIOS. For more information, see “Updating the BIOS” on page 67.
Processors and heat sinks may be hot if the computer has been
running. Also, there may be sharp edges on the heat sinks. Consider
wearing protective gloves.
Warning
without a heat sink could damage the processor.
To replace the processor:
on page 67.
2 Follow the instructions in “Preventing static electricity discharge” on page 29.
3 Follow the instructions in “Opening the server case” on page 30.
4 Follow the instructions in “Removing the processor air duct” on page 33.
5 Loosen the four captive heat sink screws (one on each corner).
www.gateway.com
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
6 Remove the heat sink.
The heat sink has Thermal Interface Material (TIM) on the bottom.
Be careful not to damage this material when you remove the heat
sink from the processor.
Caution
If removing the heat sink also pulls the processor out of the processor
socket, the processor could be damaged. Check the pins on the
processor to make sure they are not bent or damaged.
If the heatsink sticks to the processor, twist it slightly to release it, then try again.
7 Press down on the processor locking lever, push it slightly away from the processor,
then rotate the lever a full 135° to release the processor.
8 Remove the old processor.
9 Install the new processor into the processor socket. Make sure that:
■
The processor release lever is open all the way (135° from the closed position)
■
The triangular arrow on the corner of the processor aligns with the triangular
hole on the corner of the processor socket
■
The processor is flush with the socket.
10 Press the processor locking lever down until it clicks into place.
www.gateway.com
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the processor
11 Place the heat sink on the processor, making sure the Thermal Interface Material (TIM)
is aligned between the heat sink and the processor.
gradually and evenly tighten the four captive screws to secure the heat sink to the
system board.
13 Follow the instructions in “Installing the processor air duct” on page 34.
14 Follow the instructions in “Closing the server case” on page 37.
www.gateway.com
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
Replacing a power supply module
If your server uses the optional hot-swappable, redundant power supplies and one of the
two power supplies fails, the other power supply module supports the server while you
replace the failed module. You do not need to turn off the server or disconnect peripheral
devices to replace a failed power supply module.
The power supply modules in this server contain no user-serviceable
parts. Only a qualified computer technician should service the power
supply modules.
Warning
Your server comes with 3-wire AC power cords fitted with the correct
plug style for your region. If this plug does not match the connector
on your surge protector, UPS, or wall outlet, do not attempt to modify
the plug in any way. Use a UPS or wall outlet that is appropriate for
the supplied AC power cords.
To replace a power supply module:
1 If you only have one power supply module, turn off your server.
2 If you have two power supply modules, examine the LED indicators on the back of
each power supply module to identify the failed module. The power supply module
has failed if the orange (right) LED indicator is on.
Power supply handle
Power supply fault LED
Power connector
Power supply latch
Power on LED
3 Unplug the power cord from the failed power supply module.
www.gateway.com
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing a power supply module
4 While pressing the green latch on the power supply module, grasp the handle and
pull the module straight out from the server.
5 Slide the new power supply module into the empty power supply bay until the green
latch snaps into place.
6 Plug the power cord into the new power supply module.
www.gateway.com
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
Replacing a fan
Important
1 Follow the instructions in “Preventing static electricity discharge” on page 29.
2 Follow the instructions in “Opening the server case” on page 30.
3 Remove the processor air duct by following the instructions in “Removing the
processor air duct” on page 33.
4 Unplug the fan cable from the fan connector on the system board.
Fan retention
tab
Fan release
tab
Fan handle
Fan retention
tab
Fan cable
5 Grasp the fan handle and press the fan release tab, then disengage the fan and move
it away from the chassis.
6 Pull the fan from the chassis.
www.gateway.com
56
Download from Www.Somanuals.com. All Manuals Search And Download.
tabs and fan release tab with the chassis until it snaps into place.
8 Plug the fan cable into the fan connector on the system board.
9 Replace the processor air duct by following the instructions in “Installing the processor
air duct” on page 34.
To replace a back fan:
1 Follow the instructions in “Preventing static electricity discharge” on page 29.
2 Follow the instructions in “Opening the server case” on page 30.
3 Unplug the fan cable from the fan connector on the system board.
Fan cable
Fan retention
screw
Fan retention
screw
www.gateway.com
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
4 Unscrew the four fan retention screws holding the fan to the back of the chassis.
5 Pull the fan from the chassis, noting the orientation.
Make sure that the new fan is oriented the same way (air flow) as
the old fan.
Important
7 Plug the fan cable into the fan connector on the system board.
8 Follow the instructions in “Closing the server case” on page 37.
www.gateway.com
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the CMOS battery
Replacing the CMOS battery
If the server clock does not keep time or the settings in the BIOS Setup utility are not saved
when you turn off the server, replace the CMOS battery with an equivalent battery.
Warning
To replace the battery:
3 Record the BIOS settings on your printout, then close the utility.
discharge” on page 29.
5 Follow the instructions in “Opening the server case” on page 30.
6 Locate the old battery on the system board and note its orientation (see “System
board” on page 5 for the general location of the battery). You will need to install the
new battery the same way.
Battery retention
clip
7 Push the battery retention clip away from the battery until the battery pops up.
8 Remove the old battery.
www.gateway.com
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
9 Make sure that the positive (+) side of the new battery is facing correctly, then press
the new battery into the socket until it snaps into place.
11 Turn on the server.
12 Press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility
opens.
13 Restore any BIOS settings that you wrote down in Step 3.
14 Save all your settings and close the BIOS Setup utility.
www.gateway.com
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the system board
Replacing the system board
5 Remove all of the expansion cards by following the instructions in “Installing PCI
expansion cards” on page 47.
6 Remove the heat sink and processor by following the instructions in “Replacing the
processor” on page 51.
7 Disconnect the power and data cables from the system board, noting their locations
and orientation. (You will reconnect the cables after you install the new board.)
www.gateway.com
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
8 Remove the seven (7) screws securing the system board to the case.
Screw
Screw
Screw
Screw
Screw
Screw
Screw
www.gateway.com
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the system board
9 Pull the system board away from the case and carefully remove it, then place it in a
static-free bag on a stable work surface.
threaded standoffs on the side of the case.
page 45.
processor” on page 51.
14 Connect the power and data cables.
15 Reinstall the expansion cards by following the instructions in “Installing PCI
expansion cards” on page 47.
16 Follow the instructions in “Closing the server case” on page 37.
www.gateway.com
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Installing Components
17 Turn on your server.
18 Press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility
opens.
19 Check BIOS settings to make sure that they detect the server’s new hardware, then
save your changes (if any) and close the BIOS Setup utility.
www.gateway.com
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Using the BIOS Setup Utility
Opening the BIOS Setup utility
The BIOS Setup utility stores basic settings for your server. These settings include basic
hardware configuration, resource settings, and password security. These settings are stored
and saved even when the power is off.
The options in the BIOS Setup utility have been set at the factory for
optimal performance. Changes to these settings will affect the
performance of your server.
Caution
Before changing any settings, write them down in case you need to
restore them later. You can record the settings on a printout of “BIOS
Settings” on page 95.
To open the BIOS Setup utility:
1 Restart your server.
2 Press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility
opens.
When you select menu items, the Item Specific Help box on the right side of the screen
displays specific information about the selection. The command bar across the bottom
of the screen shows the keys you press to access help, navigate through the menus,
and perform other tasks.
3 Select one of these menus (for a complete list of menu and sub-menu options, see
“BIOS Settings” on page 95):
■
■
■
hardware and configuration.
Advanced gives you access to information and settings for system resources,
hardware, and server’s configuration.
Security gives you access to settings related to system access passwords. For more
information, see “Server security” on page 19.
■
■
Power gives you access to settings for system power management.
Boot gives you access to information and settings for startup features and startup
sequences.
■
Exit gives you access to options for closing the BIOS Setup utility.
www.gateway.com
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Updating the BIOS
Updating the BIOS
If you need a new version of the BIOS, you can download the BIOS update from
support.gateway.com, then install the new version from Windows.
To update the BIOS:
Make sure you write down the location of the unzipped files, so you
can locate them later.
Important
2 Print the appendix for BIOS Settings in this guide.
startup. The BIOS setup utility opens.
Windows-based BIOS update utility named WT72310J.15A.xxxx.xx.exe (or similar)
(found in the location you wrote down after Step 1).
Windows restarts the server and automatically flashes the BIOS.
6 Enter any custom BIOS settings you recorded in Step 4, then save your changes and
close the BIOS Setup utility.
www.gateway.com
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Using the BIOS Setup Utility
Resetting the BIOS
After a successful BIOS update, if one or more applications do not subsequently run you
may want to clear the settings and return to the old BIOS. The Clear BIOS jumper on the
system board lets you return all BIOS settings to the factory defaults.
Important
BIOS.
To reset the BIOS:
1 Print the appendix for BIOS Settings in this guide.
2 Restart your server.
3 Press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility
opens.
5 Follow the instructions in “Preventing static electricity discharge” on page 29.
6 Turn off the server, then disconnect the power cords and all other cables connected
to the server.
7 Follow the instructions in “Opening the server case” on page 30.
Moving the jumper while the power is on can damage your server.
Always turn off the server and unplug the power cords and all other
cables before changing the jumper.
Caution
8 Remove the jumper across pins 1-2 of header J3F3, then place the jumper across
pins 2-3.
Jumper
J3F3
www.gateway.com
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Resetting the BIOS
10 Reconnect the power cords and turn on the server. The BIOS memory is cleared.
to the server.
12 Follow the instructions in “Opening the server case” on page 30
13 Place the jumper back onto pins 1-2.
14 Follow the instructions in “Closing the server case” on page 37.
15 Turn on the server. A message appears saying that the CMOS Date and Time are not set.
16 Press F1 to reset the BIOS to factory default settings.
Resetting BIOS passwords
To reset BIOS password(s), you must either reset and clear all BIOS settings, or use the
Password Clear jumper. To reset BIOS passwords, follow the instructions in “Resetting the
BIOS” on page 68.
To clear the BIOS password(s):
1 Turn off the server, then disconnect the power cords and all other cables connected
to the server.
2 Follow the instructions in “Opening the server case” on page 30.
Moving the jumper while the power is on can damage your server.
Always turn off the server and unplug the power cords and all other
cables before changing the jumper.
Caution
www.gateway.com
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Using the BIOS Setup Utility
3 Remove the jumper across pins 1-2 of header J3F3, then place the jumper across
pins 2-3.
Jumper
J3F3
5 Reconnect the power cords and turn on the server. The BIOS password(s) is cleared.
to the server.
7 Follow the instructions in “Opening the server case” on page 30.
8 Place the jumper back onto pins 1-2.
9 Follow the instructions in “Closing the server case” on page 37.
www.gateway.com
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Troubleshooting
Safety guidelines
While troubleshooting your server, follow these safety guidelines:
■
Never remove the side panel while your server is turned on and while the modem
cable and the power cords are connected.
Do not attempt to open the monitor. To do so is extremely dangerous. Even if the
power is disconnected, energy stored in the monitor components can be dangerous.
Also, opening the monitor voids its warranty.
■
Make sure that you are grounded correctly before opening the server case. For more
information about preventing damage from static electricity, see “Preventing static
electricity discharge” on page 29.
■ After you complete any maintenance task where you have to open the server case,
make sure that you close the case, tighten any screws, then reconnect all cables
before you restart your server.
To avoid bodily injury, do not attempt to troubleshoot your server
problem if:
Warning
■
Power cords or plugs are damaged
Liquid has been spilled into your server
Your server was dropped
The case was damaged
■
■
■
Instead, unplug your server and contact a qualified computer
technician. If your server was damaged during shipment from
Gateway, contact Gateway Customer Care.
www.gateway.com
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Error messages
Error messages
These messages often indicate procedural errors such as typing an incorrect keystroke or
trying to save a file to a write-protected diskette. Some messages, however, may indicate
a problem that requires further troubleshooting. These are general messages and do not
represent all possible error messages you might receive.
while your server restarts. Make sure that the drive settings are correct.
Error loading operating system
■ The master boot record may be corrupt. For troubleshooting information, see “The
master boot record is corrupted” on page 81.
Hard disk controller failure
■
Make sure that the data cables to the hot swap hard drive cage are connected
securely.
■ Restart your server, then open the BIOS Setup utility by pressing and holding F2
while your server restarts. Make sure that the correct drive type is selected.
Hard disk controller failure - press F1 to try reboot
■
The drive controller may be defective. Press F1 to try to restart the server. For more
information about running diagnostics on your hard drive, see your operating
system’s documentation.
Insert bootable media device
Restart your server, then open the BIOS Setup utility by pressing and holding F2
■
while your server restarts. Make sure that the correct hard drive is set as the first
bootable drive in the Boot menu.
Invalid configuration information
■
■ Reset the BIOS. For more information, see “Resetting the BIOS” on page 68.
Invalid partition table
■ The master boot record may be corrupt. For troubleshooting information, see “The
master boot record is corrupted” on page 81.
www.gateway.com
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Troubleshooting
Invalid password
■
Enter your password again. Some passwords are case sensitive.
■
If you do not know the password, you may need to reinstall the software you are
trying to access.
do not know it, you may be able to reset the password through system board jumper
settings. For more information, see “Resetting BIOS passwords” on page 69.
Memory errors were detected while the system started up
■ See “Memory errors were detected during server start up” on page 82 for a possible
solution.
while your server restarts. Save the memory configuration.
Missing operating system
■ The master boot record may be corrupt. For troubleshooting information, see “The
master boot record is corrupted” on page 81.
System Event Log Full
■ Clear the event log. To clear or view the event log, restart your server, then open
the BIOS Setup utility by pressing and holding F2 while your server restarts. Select
the Advanced menu, then select the Event Log Control menu.
www.gateway.com
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
First steps
Try these steps first before going to the following sections:
■
■
■
Make sure that the power cords are connected to your server and an AC outlet and
that the AC outlet is supplying power.
If you use a UPS, make sure that it is turned on and is rated to handle the power
required by your server.
If you added or removed server components before the problem started, review
the installation procedures you performed and make sure that you followed each
instruction. You may need to remove the device, uninstall the device’s software,
then reinstall the device.
■
■
If an error message appears on the screen, write down the exact message before
calling Gateway Customer Care.
Restart your server, then open the BIOS Setup utility by pressing and holding F2
while your server restarts. Check your configuration settings.
■ If an error occurs in a program, see its documentation or online help.
To avoid bodily injury, do not attempt to troubleshoot your server
problem if:
Warning
■
Power cords or plugs are damaged
Liquid has been spilled into your server
Your server was dropped
The case was damaged
■
■
■
Instead, unplug your server and contact a qualified computer
technician. If your server was damaged during shipment from
Gateway, contact Gateway Customer Care.
Battery replacement
closing the case and restarting the server after each try:
■ Restart your server, then open the BIOS Setup utility by pressing and holding F2
while your server restarts. Correct any discrepancies.
■ Remove the side panel by following the instructions in “Opening the server case”
on page 30, then make sure that all cables inside the case are attached securely.
Also, make sure that the colored cable edges are aligned correctly and that the
connectors do not miss any pins.
www.gateway.com
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Troubleshooting
■ If you have the correct test equipment, make sure that the new battery has power.
Although unlikely, your new battery may be defective.
Beep codes
Whenever a recoverable error occurs during the power-on self-test (POST), the BIOS
displays an error message that describes the problem. The BIOS also sounds a beep code
(one long tone followed by two short tones) during POST if the video configuration fails
(a faulty video controller) or if an expansion card is not functioning correctly. One short
beep indicates the BIOS will boot the operating system. No error found.
A PCI expansion card (for example, a RAID controller) can also issue audible errors by itself,
usually consisting of one long tone followed by a series of short tones. For more
information on the beep codes issued, check the documentation for that device.
The following table shows POST error beep codes. Prior to system video initialization, BIOS
uses these codes to inform users of error conditions.
Beeps
Description
Troubleshooting steps
1
Memory refresh timer error
Reseat the memory modules or replace with
modules you know are good.
2
3
4
Parity error in the first 64 KB of memory.
Base memory read/write test error
System board timer not operational.
Same as for 1 beep.
Same as for 1 beep.
Possible system board malfunction. To
eliminate the possibility of an add in-card
problem, remove all expansion cards.
■
If the beep code occurs even when all
expansion cards have been removed, the
system board is at fault.
If the beep code does not occur when the
■
expansion cards have been removed, one
of the cards is causing the problem. Install
the cards one at a time until the problem
happens again. When the beep code
returns, the most recent card you installed
is at fault.
5
6
The processor on the system board
generated an error.
Try a known good processor in the processor
socket.
Same as for 4 beeps.
The keyboard controller (8042) may be
defective. The BIOS cannot switch to
Protected mode.
Remove the keyboard to see if the error goes
away. If it does, try a known good keyboard.
Same as for 4 beeps.
www.gateway.com
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Beeps
Description
Troubleshooting steps
7
General exception error (processor
exception error).
Same as for 4 beeps.
Same as for 5 beeps
8
Display memory error (system video
adapter).
If the system video adapter is an add-in card,
replace or reseat the video adapter. If the
video adapter is integrated into the system
board, the board may be faulty. Try using an
add-in card.
9
The ROM checksum value does not match
the value encoded in the BIOS.
Same as for 4 beeps.
10
11
The shutdown register for CMOS RAM failed. Same as for 4 beeps.
The cache memory test failed. Same as for 4 beeps.
www.gateway.com
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Troubleshooting
DIM code checkpoints
The Device Initialization Manager (DIM) gets control at various times during BIOS POST
to initialize different system buses. The following table describes the main checkpoints
where the DIM module is accessed.
Checkpoint
Description
2A
Initialize different buses and perform the following
functions:
■
Reset, Detect, and Disable (function 0) — Disables all
device nodes, PCI devices, and PnP ISA cards. It also
assigns PCI bus numbers.
Static Device Initialization (function 1) — Initializes all
■
static devices that include manual configured onboard
peripherals, memory and I/O decode windows in
PCI-PCI bridges, and noncompliant PCI devices. Static
resources are also reserved.
■
Boot Output Device Initialization (function 2) —
Searches for and initializes any PnP, PCI, or AGP video
devices.
38
Initialize different buses and perform the following
functions:
■
Boot Input Device INitialization (function 3) —
Searches for and configures PCI input devices and
detects if system has standard keyboard controller.
IPL Device Initialization (function 4) — Searches for
■
and configures all PnP and PCI boot devices.
General Device Initialization (function 5) — Configures
■
all onboard peripherals that are set to an automatic
configuration and configures all remaining PnP and
PCI devices.
ACPI runtime checkpoints
ACPI checkpoints are displayed when an ACPI-capable operating system either enters or
leaves a sleep state. The following table describes the types of checkpoints that may occur
during ACPI sleep or wake events:
Checkpoint
Description
AC
First ASL checkpoint. Indicates that the system is
running in ACPI mode.
AA
System is running in APIC mode.
01, 02, 03, 04, 05 Entering sleep state S1, S2, S3, S4, or S5.
10, 20, 30, 40, 50 Waking from sleep state S1, S2, S3, S4, or S5.
www.gateway.com
78
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS
The settings in the BIOS Setup utility are not retained
■ Replace the CMOS battery. For more information, see “Replacing the CMOS
battery” on page 59.
CD or DVD drive
Your server does not recognize a CD, DVD, or the CD or DVD drive
■
Restart your server, then open the BIOS Setup utility by pressing and holding F2
while your server restarts. Make sure that the IDE controllers are enabled. For more
information, see “Using the BIOS Setup Utility” on page 65.
■
■
Reinstall the device driver. For more information, see Using Your System Companion
CD.
Make sure that the drive is configured correctly by following the instructions in
the drive’s documentation.
■ Open your server case and make sure that the cables are connected correctly to
the CD or DVD drive and the IDE connector on the system board or controller card.
Your CD or DVD drive tray does not open
■
Press a straightened paper clip wire into the CD or DVD drive’s manual eject hole.
The drive tray opens.
■ If this problem happens frequently while the server is turned on, the drive may
be defective.
Diskette drive
The diskette drive is not recognized
Restart your server.
■
cable indicates Pin 1 and corresponds with Pin 1 on the diskette drive (typically
on the side farthest from the power supply connection). If necessary, reverse one
end of the cable so the red-striped edge of the data ribbon cable faces Pin 1 on
the diskette drive. Make sure that the pins are not bent or misaligned. For more
information, see “Installing drives” on page 38.
www.gateway.com
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Troubleshooting
The diskette drive LED is lit continuously
■
Remove the diskette from the drive. If the light stays on, try restarting your server.
indicates Pin 1 and corresponds with Pin 1 on the diskette drive (typically on the
side farthest from the power supply connection). If necessary, reverse one end of
the cable so the red-striped edge of the data ribbon cable faces Pin 1 on the diskette
drive. Make sure that the pins are not bent or misaligned. For more information,
see “Installing drives” on page 38.
Expansion cards
■
■
Make sure that you have installed the necessary software or driver. For more
information, see the card’s documentation.
■
Reseat the card. For more information, see “Installing PCI expansion cards” on
page 47.
■ Install the card in a different slot.
Hard drive
The hard drive cannot be accessed, or you receive a “General failure reading drive C”
error message
■
If a diskette is in the diskette drive, eject it and restart your server by pressing the
reset button.
■
■
Restart your server by pressing the reset button.
Open your server and make sure that the cables are connected correctly to the hard
drive.
You receive a “Non-system disk” or “disk error” error message
■
Eject the diskette from the diskette drive, then press ENTER.
■ Make sure that your hard drive has an active partition. For more information, see
“The master boot record is corrupted” on page 81.
www.gateway.com
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Your server does not recognize a SCSI drive
■
Make sure that the SCSI controller is enabled in the BIOS Setup utility.
■
Reinstall the device driver. For more information, see Using Your System Companion
CD.
■
■
Change the drive’s SCSI address to one that is not being used by your server. For
more information about SCSI device configurations, see your drive’s
documentation.
the SCSI controller’s documentation.
■
■
Reseat the drive.
Open your server and reseat the drive controller card. Also make sure that the
controller card and power cables are connected to the drive. For more information,
see “Installing PCI expansion cards” on page 47 or your controller card’s
documentation.
■
■
Make sure that the power cable and SCSI cable are attached securely to the drive
cage.
Make sure that the last device on the SCSI cable is correctly terminated. For more
information about SCSI device configurations, see the device’s documentation.
■ Use a different SCSI cable.
You are having problems with a SATA drive
■
For normal SATA drives (not SATA RAID), check the BIOS setup utility to see if the
BIOS has recognized the drive.
■
Make sure that the power cable and SATA cables are attached securely to the drive
cage.
■
■
■
If the drive is not detected, try a different SATA port.
Try swapping SATA cables between drives to determine if the cable is defective.
Try listening to the drive to determine if the drive is spinning up. If not, the drive
may be defective.
The master boot record is corrupted
■ In a Windows network operating system, repair the master boot record using FDISK.
To repair the master boot record:
■
At a DOS command prompt, type fdisk/mbr, then press ENTER.
www.gateway.com
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Troubleshooting
Internet
See also Modem.
You cannot connect to the Internet
■
Make sure that your account with your Internet Service Provider (ISP) is set up
correctly. Contact your ISP technical support for help.
■ Make sure that you do not have a problem with your modem. For more
information, see “Modem (telephone dial-up)” on page 82.
Keyboard
Liquid has been spilled into the keyboard
■ If you spilled liquid into the keyboard, turn off your server and unplug the
keyboard. Clean the keyboard and turn it upside down to drain it. Let the keyboard
dry before using it again. If the keyboard does not work after it dries, you may
need to replace it. This type of damage is not covered by your server’s warranty.
Memory
Memory errors were detected during server start up
■
Open your server and make sure that the memory modules are installed correctly.
For more information, see “Installing memory” on page 45.
■ A memory module may be defective. If possible, try another memory module and
see if the error repeats.
Modem (telephone dial-up)
See also Internet.
Your modem does not dial or does not connect
■
■
Make sure that your server is connected to the telephone line and the telephone
line has a dial tone.
Make sure that the modem cable is less than 6 feet (1.8 meters) long.
www.gateway.com
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
■
Remove any line splitters or surge protectors from your telephone line, then check
for a dial tone by plugging a working telephone into the telephone jack.
■ If you have additional telephone services such as call waiting, call messaging, or
voice mail, make sure that all messages are cleared and call waiting is disabled
before using the modem. Contact your telephone service to get the correct code
to temporarily disable the service. Also make sure that the modem dialing
properties are set correctly.
To check the dialing properties in Windows 2000 Server:
1 Click Start, Settings, then click Control Panel. The Control Panel window opens.
2 Double-click the Modems icon, then click Dialing Properties. The Dialing Properties
dialog box opens.
3 Make sure that all settings are correct.
■
■
Make sure that you are not using a digital, rollover, or PBX line. These lines do
not work with your modem.
Check for line noise (scratchy, crackling, or popping sounds). Line noise is a
common problem that can cause the modem to connect at a slower rate, abort
downloads, or even disconnect. The faster the modem, the less line noise it can
tolerate and still work correctly.
Listen to the line using your telephone. Dial a single number (such as 1). When the
dial tone stops, listen for line noise. Wiggle the modem cable to see if that makes a
difference. Make sure that the connectors are free from corrosion and all screws in
the wall or telephone jack are secure.
You can also call your telephone service and have your telephone line checked for
noise or low line levels.
■
Try connecting with the modem at a lower connection speed. If reducing the
connection speed lets you connect, contact your telephone service. The telephone
line may be too noisy.
■ Try another telephone line (either a different telephone number in your business
or a telephone line at a different location). If you can connect on this line, call
your telephone service to fix the original line.
Your 56K modem does not connect at 56K
Current FCC regulations restrict actual data transfer rates over public telephone lines to
53K. Other factors, such as line noise, telephone service provider equipment, or ISP
limitations, may lower the speed even further.
www.gateway.com
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Troubleshooting
If your system has a v.90 modem, the speed at which you can upload (send) data is limited
to 33.6K. If your system has a v.92 modem, the speed at which you can upload data is
limited to 48K. Your ISP may not support 48K uploads.
The modem is not recognized by your server
■
If the modem shares the telephone line with another device, make sure that the
telephone line is not in use (for example, someone is on the telephone, or another
■
■
Reinstall the modem device driver. For more information, see Using Your System
Companion CD.
■ Open your server and reseat the modem. For more information, see “Installing PCI
expansion cards” on page 47.
Monitor
Your server is running but there is no picture
■
■
Adjust the brightness and contrast controls to the center position.
Make sure that the monitor is plugged in and turned on. If the monitor is turned
on, the power LED should be lit.
■
Check the port and cable for bent or damaged pins.
■ Connect your monitor to another computer, or connect a monitor that you know
works to your server.
The color is not uniform
Make sure that the monitor warms up for at least 30 minutes before making a final
judgment about color uniformity.
Make sure that:
■
The monitor is not positioned too close to another monitor, electric fan, or
fluorescent light.
■ You demagnetize the screen using the monitor’s degauss feature. For more
information on degauss, see the monitor’s documentation.
www.gateway.com
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
A horizontal line or wire is visible across the monitor screen
The monitor may use thin damper wires, located approximately 1/3 of the way from the
upper and lower screen edges, to stabilize the internal aperture grille. These wires are most
obvious when the monitor displays a white background. The aperture grille allows more
light to pass through the screen for brighter colors and greater luminescence. The damper
wire is a critical part of the overall monitor design and does not negatively affect the
monitor’s function.
Power
You press the power button, but the server does not turn on
■
■
■
If the power button LED is green, the server is turned on, but you may not be seeing
an image on the monitor. For monitor troubleshooting, see “Monitor” on page 84.
If your server is equipped with redundant power supply modules, check the LEDs
on the power supply modules.
If your server is plugged into a UPS, make sure that the UPS is connected securely
to an electrical outlet, turned on, and working correctly. One way to check this is
to plug the server directly into a wall outlet, bypassing the UPS.
■
Make sure that the electrical outlet is working by plugging a working device, such
as a lamp, into the outlet, then turning it on to test the outlet.
cable are connected correctly to the system board.
When you turn on the server, it makes several short beeps
■ The short beeps indicate the server has encountered some type of error. See “Beep
codes” on page 76.
Processor
Your server does not recognize a new processor
■
Make sure that the processor is fully seated in its socket. The processor should be
recognized automatically if it is installed correctly.
www.gateway.com
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Troubleshooting
Telephone support
Before calling Gateway Customer Care
If you have a technical problem with your server, follow these recommendations before
contacting Gateway Customer Care:
■
■
■
Make sure that your server is connected correctly to a grounded AC outlet that is
supplying power.
If a peripheral device, such as a keyboard or mouse, does not appear to work, make
sure that all cables are plugged in securely.
If you have recently installed hardware or software, make sure that you have
installed it following the instructions provided with it. If you did not purchase the
hardware or software from Gateway, see the manufacturer’s documentation and
technical support resources.
■
If you have “how to” questions about using a program, see:
■
■
■
■
The program’s online Help
The program’s documentation
Your operating system’s documentation
The software or hardware manufacturer’s Web site
■
■
See “Troubleshooting” on page 75.
Have your client ID, serial number (located on the back of your server case), and
order number available, along with a detailed description of your issue, including
the exact text of any error messages, and the steps you have taken.
■
■
The COA, or Certificate of Authenticity, if required, is normally located on the side
panel of the server.
Make sure that your server is nearby at the time of your call. The technician may
have you follow appropriate troubleshooting steps.
■ Consider using Gateway’s Internet Customer Care. Gateway’s Web site has FAQs,
tips, and other technical help. You can also use the Web site to e-mail Customer
Care. For more information, visit Gateway’s Customer Care Web site at
support.gateway.com.
www.gateway.com
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Tutoring and training
Telephone support
Gateway offers a wide range of customer service, technical support, and information
services.
Telephone numbers
You can access the following services through your telephone to get answers to your
questions:
Resource
Service description NEW
How to reach
Gateway’s
fee-based
software
Get tutorial assistance for software issues.
800-229-1103 (charged to your
credit card)
tutorial service
Gateway
Talk to a Gateway Customer Care representative
877-485-1464 (US)(option #6)
800-846-3609 (Canada and
Puerto Rico)
Customer Care about a non-tutorial technical support question.
605-232-2191
(all other countries)
Sales,
accounting,
and warranty
Get information about available systems, pricing,
orders, billing statements, warranty service, or
other non-technical issues.
800-846-2000 (US)
888-888-2037 (Canada)
Tutoring and training
Gateway's Customer Care professionals cannot provide hardware and software training.
Instead, Gateway recommends the following training resources.
Resource
Service description
For more information
Gateway
Learning
Libraries
A variety of courses and tutorials are available
on CD. Select from several easy-to-use
learning libraries.
www.gateway.com/training
www.gateway.com
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Troubleshooting
www.gateway.com
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A:
System specifications
Tower (with standard power supply): 8 × 16.5 × 19.8 inches
(203.2 × 419.2 × 502.7 cm)
Case size
Tower (with redundant power supplies) 8 × 16.5 × 22.2 inches
(203.2 × 419.2 × 563 cm)
Approximately 32 lbs (14.5 kg) (varies by configuration)
2 chassis fans
Weight
Fans
■
PS/2 keyboard/mouse (2)
USB (6)
Serial (1)
VGA (1)
Ports
■
■
■
■
RJ-45 LAN (1)
Two 5.25” external drive bays.
Two 3.5” external drive bays.
Optional drives:
Drives
(removable
media)
■
3.5-inch diskette
CD-ROM, CD-R, or DVD-ROM
Tape drive
■
■
Support for four, SATA, or NSCA SCSI hard drives (standard)
Supports full-length, full-height PCI expansion cards
Hard Drives
Card sizes
Single 400 W fixed power supply (standard).
Power supply
modules
Two 520 W, hot-swap, redundant power suppy modules (optional).)
Supports Windows Server 2003 (all) and Small Business Server 2003
(all)
Operating
systems
Compatible with:
■
Windows NT
Novell NetWare 5.1 and 6.5
Red Hat Linux Enterprise 3.0 and 3.0 EM64T
SuSe Linux Enterprise 9.0 and 9.0 EM64T
■
■
■
■
FCC Class A
UL
cUL
Certifications
■
■
www.gateway.com
90
Download from Www.Somanuals.com. All Manuals Search And Download.
System board specifications
System board specifications
604-pin socket (FC-mPGA4 package, 90 nM technology)
533 MHz or 800 MHz Front Side Bus (FSB)
Dual-core support (Pentium D only)
Processor
Supports Intel Celeron, Pentium 4, or Pentium D CPUs with 1024 KB
cache
Intel E7230 chipset
Chipset
■
Supports 533 MHz or 800 MHz Front Side Bus (FSB)
E7230 Memory Controller Hub (MCH)
■
■
Intel 82801GR I/O Controller Hub7 (ICH-7)
Four DIMM slots support as many as 8 GB total memory
Memory
■
DDR2 533Mhz ECC unbuffered DIMM modules
DIMM organization x72 ECC
■
■
240-pin DIMMs (256 MB, 512 MB, 1 GB, or 2 GB only)
PCI slots:
PCI device/slot
■
Slot 1 - x1 PCI Express
Slot 2 - x8 PCI Express
Slot 3 - PCI 32-bit
Slot 4 - x4 PCI Express
■
■
■
■
Slot 5 - PCI 32-bit
XGI Z7 Volari 16MB 16-bit PCI Video Adapter card
Video
RAID
Four Serial ATA 150 ports from the ICH7 supporting entry level RAID
functionality, including RAID levels 0, 1, 5, and 10.
On-board Marvel Ethernet NIC
LAN
■
10Base-T/100Base-TX/1000Base-T
■
PXE support
ACPI compliance
ACPI
Supports S0, S1, S4, S5
Main logic board sensors:
Hardware
Monitor
■
Voltage sensors
Temperature sensors
■
■
Adaptive fan speed control and fan speed detection
www.gateway.com
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A:
Environmental specifications
The following specifications identify maximum environmental conditions. At no time
should the server run under conditions which violate these specifications.
Variable
Requirements
Maximum rate of change: 18°F (10°C) per hour
Nonoperating: -4° to 140°F (-20° to 60°C)
Temperature
Operating: 41° to 95°F (5° to 35°C); derated 0.9°F (0.5°C) for every
1,000 feet (305 meters)
12,500 feet (3,810 meters) maximum
Altitude
Operating: 20% to 80% relative, non-condensing
Humidity
Nonoperating: 20% to 90% relative non-condensing at 86° F (30° C)
Operating: 2.0 g, 11 msec, ½ sine
Shock
Packaged: Operational after 18-inch free fall (cosmetic damage might
occur)
100-127 V, 10.0 A, 50/60 Hz max.
200-240 V, 5.0 A, 50/60 Hz max.
AC input power
www.gateway.com
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Electronic specifications
Electronic specifications
Memory map
Address Range (hex)
0 to 07FFFFh
Amount
640 KB
128 KB
128 KB
128 KB
2 MB
Function
DOS region, base system memory
Video or SMM memory
Expansion card BIOS and buffer area
System BIOS
0A0000h to 0BFFFFh
0C0000h and 0DFFFFh
0E0000h to 0FFFFFh
0E0000h to 0EFFFFh
Extended system BIOS
PCI memory space
FC000000h to FFFFFFFFh 64 MB
Interrupts
The following table reflects a typical configuration, but you can change these interrupts.
Use this information to determine how to program each interrupt. The actual interrupt
map is defined using configuration registers in the ICH5-R (I/O controller). I/O Redirection
Registers in the I/O APIC are provided for each interrupt signal. The signals define hardware
interrupt signal characteristics for APIC messages sent to local APIC(s).
If you disable an IDE controller to free the interrupt for that controller,
you must physically unplug the IDE cable from the system board.
Important
Simply disabling the drive by configuring the BIOS does not make
the interrupt available.
Interrupt
Description
IRQ0
Timer/counter, HPET #0 in legacy
replacement Mode. In APIC mode,
cascade from 8259 controller 1
IRQ1
IRQ2
Keyboard controller
Slave controller INTR output. In APIC
mode Timer/counter, HPET #0
IRQ3
IRQ4
IRQ5
Serial port A
Serial port B
Parallel port
www.gateway.com
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A:
Interrupt
IRQ6
Description
Diskette controller
IRQ8
Real-time clock/HPET#1 in legacy
replacement mode
IRQ9
Generic, Option for SCI
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
PIRQA
PIRQB
PIRQC
PIRQD
PIRQE
PIRQF
PIRQG
PIRQH
Generic, Option for SCI
HPET #2, option for SCSI, TCO
Mouse controller
System interrupt/FERR
Primary ATA, legacy mode
USB 1.1 controller 1 and 4
Video
USB 1.1 controller 3, Native IDE, SATA
USB 1.1 controller 2
Option for SCI, TCO, HPET #0,1,2
Option for SCI, TCO, HPET #0,1,2
Option for SCI, TCO, HPET #0,1,2
USB 2.0 EHCI controller 1, Option for
SCI, TCO, HPET #0,1,2
Ser IRQ
SIO3
Additional specifications
For more information about your server, such as memory size, hard drive size, and
processor type, visit Gateway’s Support page at support.gateway.com. The Support page also
has links to additional Gateway documentation and detailed specifications for your own
server.
www.gateway.com
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B:
To view all BIOS settings:
1 Restart your server.
2 Press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility
opens.
3 Select menus and submenus to display setting information.
BIOS menu
BIOS submenu
Setting
Value
Maintenance
Clear All Passwords
Fixed Boot Sector
Normal
Write protect
Use Maximum Multiplier (for
frequency-limited
processors the maximum
multiplier is programmed in
automatic mode).
Automatic
Disable
Intel Enhanced Debug
Disable
Enable
CPU Frequency Multiplier
Processor Stepping
Microcode Revision
Ratio Actual Value
Main
System Information:
BIOS Version
Processor (Type, Speed)
System Bus Speed
System Memory Speed
L2 Cache RAM
Hyper-Threading
Technology
Enabled
Disabled
www.gateway.com
96
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS menu
BIOS submenu
Setting
Value
System Memory (Total)
Memory Mode
Memory Channel A Slot 0
Memory Channel A Slot 1
Memory Channel B Slot 0
Memory Channel B Slot 1
System Time
System Date
Language
HH:MM:SS
DAY MM/DD/YYYY
English
French
German
Italian
Spanish
Additional system
information:
Manufacturer:
Product Name:
Version:
Serial Number:
Desktop board
information:
Manufacturer:
Product Name:
Version:
Serial Number:
Chassis information:
Manufacturer:
Version:
Serial Number:
Asset Tag:
Advanced
Boot Configuration
Numlock
Off
On
www.gateway.com
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B:
BIOS menu
BIOS submenu
Setting
Value
Max CPUID Value Limit
Disable
Enable
Display Setup Prompt
On
Off
Peripheral
Configuration
Serial Port
On-board LAN
ASF 2.0
Disable
Enable
Disable
Enable
Disable
Enable
TPM 1.2
Disable
Enable
Drive Configuration
Use Automatic Mode
ATA/IDE Mode
Disabled
Enabled
Legacy
Enhanced
Configure SATA as
S.M.A.R.T.
IDE
RAID
Disable
Enable
SATA Port 0
Value
SATA Port 1
Value
SATA Port 2
Value
SATA Port 3
Value
Primary Master
Primary Slave
Hard Disk Pre-Delay
Value
Value
Value (Default = 0)
www.gateway.com
98
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS menu
BIOS submenu
Setting
Value
Floppy
Configurationi
Diskette Controller
Automatic
Disable
Enable
Diskette Write Protect
Floppy Type
Disable
Enable
1.44MB
2.88MB
Event Log
Configuration
View Event Log
Clear Event Log
Disable
Enable
Event Logging
Disable
Enable
Mark Events as Read
Disable
Enable
Video
Configuration
Primary Video Adapter
Auto
Ext PCIE Graphics
(PEG)
Ext PCI Graphics
Chipset
Configuration
PCI Express Configuration
Link to sub-menu on
page 102
www.gateway.com
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B:
BIOS menu
BIOS submenu
Setting
Value
PCI Latency Timer
32
64
96
128
160
192
224
248
Management
Configuration
ASF Support
Enable
Disable
Enter AMT BX Setup
Disable
Enable
USB Configuration
USB 2.0
Enable
Disable
USB ZIP Emulation Type
Floppy
Hard Disk
Security
Set Supervisor Password
Set User Password
User Access Level
Installed
Not Installed
Installed
Not Installed
No Access
View Only
Limited Access
Full Access
Expansion Card Text
Chassis Intrusion
Disable
Enable
Disable
Enable
www.gateway.com
100
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS menu
Power
BIOS submenu
Setting
Value
XD Technology
Disable
Enable
After Power Failure
Stay off
Last state
Power on
Wake on LAN from S5
ACPI Suspend State
Stay off
Power on
S1 State
S3 State
Boot
Boot Menu Type
Normal
Advance
Boot Device Priority
CD/DVD-ROM Drive
Floppy Drive
Hard Disk Drive
Ethernet
Hard Drive Order
(Value)
CD/DVD-ROM Drive Order
Removable Drive Order
Boot to Optical Devices
(Value)
(Drive order)
Disable
Enable
Boot to Removable Devices
Boot to Network
Disable
Enable
Disable
Enable
USB Boot
Disable
Enable
www.gateway.com
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B:
The following second level submenu is accessed from the submenu indicated in the first
column.
BIOS submenu BIOS 2nd level
submenu
Setting
Value
PCI Express
Configuration
PEG Negotiated Width
Compliance Test Pattern
(Value)
Enable
Disable
www.gateway.com
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C:
Important safety information
Your Gateway system is designed and tested to meet the latest standards for safety of information technology
equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the
product and in the documentation are followed.
Always follow these instructions to help guard against personal injury
and damage to your Gateway system.
Warning
Setting up your system
■
Read and follow all instructions marked on the product and in the documentation before you operate your
system. Retain all safety and operating instructions for future use.
■
■
■
■
Do not use this product near water or a heat source such as a radiator.
Set up the system on a stable work surface.
The product should be operated only from the type of power source indicated on the rating label.
If your computer has a voltage selector switch, make sure that the switch is in the proper position for your area.
The voltage selector switch is set at the factory to the correct voltage.
■
■
Openings in the computer case are provided for ventilation. Do not block or cover these openings. Make sure
you provide adequate space, at least 6 inches (15 cm), around the system for ventilation when you set up your
work area. Never insert objects of any kind into the computer ventilation openings.
Some products are equipped with a three-wire power cord to make sure that the product is properly grounded
when in use. The plug on this cord will fit only into a grounding-type outlet. This is a safety feature. If you are
unable to insert the plug into an outlet, contact an electrician to install the appropriate outlet.
■
■
If you use an extension cord with this system, make sure that the total ampere rating on the products plugged
into the extension cord does not exceed the extension cord ampere rating.
If your system is fitted with a TV Tuner, cable, or satellite receiver card, make sure that the antenna or cable
system is electrically grounded to provide some protection against voltage surges and buildup of static charges.
Care during use
■
Do not walk on the power cord or allow anything to rest on it.
Do not spill anything on the system. The best way to avoid spills is to avoid eating and drinking near your
system.
Some products have a replaceable CMOS battery on the system board. There is a danger of explosion if the
CMOS battery is replaced incorrectly. Replace the battery with the same or equivalent type recommended by
the manufacturer. Dispose of batteries according to the manufacturer’s instructions.
When the computer is turned off, a small amount of electrical current still flows through the computer. To
avoid electrical shock, always unplug all power cables and modem cables from the wall outlets before cleaning
the system.
■
■
■
This unit has two power supplies. To remove power from all internal
circuitry you must disconnect both power cords.
Warning
■
Unplug the system from the wall outlet and refer servicing to qualified personnel if:
■
The power cord or plug is damaged.
Liquid has been spilled into the system.
The system does not operate properly when the operating instructions are followed.
The system was dropped or the cabinet is damaged.
■
■
■
■
The system performance changes.
Replacement parts and accessories
Use only replacement parts and accessories recommended by Gateway.
www.gateway.com
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not use Gateway products in areas classified as hazardous
locations. Such areas include patient care areas of medical and
dental facilities, oxygen-laden environments, or industrial facilities.
Important
Warning
To reduce the risk of fire, use only No. 26 AWG or larger
telecommunications line cord.
www.gateway.com
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C:
Regulatory compliance statements
United States of America
Federal Communications Commission (FCC)
Unintentional emitter per FCC Part 15
FCC Part 15 Class A Statement
The server is designated as complying with Class A requirements if it bares the following text on the rating label:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
commercial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference with radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference, in
which case you will be required to correct the interference at your own expense.
Changes or modifications not expressly approved by Gateway could
void the FCC compliance and negate your authority to operate the
product.
Caution
Telecommunications per FCC part 68
(applicable to products fitted with USA modems)
Your modem complies with Part 68 of the Federal Communications Commission (FCC) rules. On the computer
or modem card is a label that contains the FCC registration number and Ringer Equivalence Number (REN) for
this device. If requested, this information must be provided to the telephone company.
An FCC-compliant telephone line cord with a modular plug is required for use with this device. The modem is
designed to be connected to the telephone network or premises wiring using a compatible modular jack which is
Part 68-compliant. See installation instructions for details.
The Ringer Equivalence Number (REN) is used to determine the number of devices which may be connected to
the telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an
incoming call. In most areas, the sum of RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.
If this device causes harm to the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. The telephone company may request that you disconnect
the equipment until the problem is resolved.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could
affect the operation of this equipment. If this happens, the telephone company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted service.
This equipment cannot be used on telephone company-provided coin service. Connection to party line service is
subject to state tariffs. Contact the state public utility commission or public service commission for information.
When programming or making test calls to emergency numbers:
■
Remain on the line and briefly explain to the dispatcher the reason for the call.
Perform such activities in the off-peak hours such as early morning or late evenings.
■
www.gateway.com
106
Download from Www.Somanuals.com. All Manuals Search And Download.
The United States Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a
computer or other electronic device to send any message via a telephone fax machine unless such message
clearly contains, in a margin at the top or bottom of each transmitted page or on the first page of the
transmission, the date and time it is sent, an identification of the business, other entity, or other individual
sending the message, and the telephone number of the sending machine or such business, other entity, or
individual. Refer to your fax communication software documentation for details on how to comply with the
fax-branding requirement.
FCC declaration of conformity
Responsible party:
Gateway Companies, Inc.
610 Gateway Drive, North Sioux City, SD 57049
(605) 232-2000 Fax: (605) 232-2023
Product:
■
Gateway E-9220T Server
For unique identification of the product configuration, please submit the 10-digit serial number found on the
product to the responsible party.
This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Gateway could
void the FCC compliance and negate your authority to operate the
product.
Caution
Canada
Industry Canada (IC)
Unintentional emitter per ICES-003
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set
out in the radio interference regulations of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de Classe A prescrites dans le règlement sur le brouillage radioélectrique édicté par
Industrie Canada.
Telecommunications per DOC notice
(for products fitted with an IC-compliant modem)
The Industry Canada label identifies certified equipment. This certification means that the equipment meets
certain telecommunications network protective, operation, and safety requirements. The Department does not
guarantee the equipment will operate to the users’ satisfaction.
Before installing this equipment, users should make sure that it is permissible to be connected to the facilities of
the local telecommunications company. The equipment must also be installed using an acceptable method of
connection. In some cases, the inside wiring associated with a single-line individual service may be extended by
means of a certified connector assembly. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by
the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect the equipment.
www.gateway.com
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C:
Users should make sure, for their own protection, that the electrical ground connections of the power utility,
telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may
be particularly important in rural areas.
To avoid electrical shock or equipment malfunction do not attempt to
make electrical ground connections by yourself. Contact the
appropriate inspection authority or an electrician, as appropriate.
Warning
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer
Equivalence Numbers of all the devices does not exceed 5.
www.gateway.com
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Laser safety statement
All Gateway systems equipped with CD and DVD drives comply with the appropriate safety standards, including
IEC 825. The laser devices in these components are classified as “Class 1 Laser Products” under a US Department
of Health and Human Services (DHHS) Radiation Performance Standard. Should the unit ever need servicing,
contact an authorized service location.
Use of controls or adjustments or performance of procedures other
Warning
than those specified in this manual may result in hazardous radiation
exposure. To prevent exposure to laser beams, do not try to open the
enclosure of a CD or DVD drive.
California Proposition 65 Warning
This product contains chemicals, including lead, known to the State
of California to cause cancer and/or birth defects or reproductive
harm.
Warning
www.gateway.com
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C:
Environmental information
The product you have purchased contains extracted natural resources that have been used in the manufacturing
process. This product may contain substances known to be hazardous to the environment or to human health.
To prevent releases of harmful substances into the environment and to maximize the use of our natural
resources, Gateway provides the following information on how you can responsibly recycle or reuse most of the
materials in your “end of life” product.
Waste Electrical and Electronic Equipment (commonly known as WEEE) should never be
disposed of in the municipal waste stream (residential garbage collection). The “Crossed-Out
Waste Bin” label affixed to this product is your reminder to dispose of your “end of life”
product properly.
Substances such as glass, plastics, and certain chemical compounds are highly recoverable,
recyclable, and reusable. You can do your part for the environment by following these simple
steps:
■
When your electrical or electronic equipment is no longer useful to you, “take it back” to your local or regional
waste collection administration for recycling.
■
In some cases, your “end of life” product may be “traded in” for credit towards the purchase of new Gateway
equipment. Call Gateway to see if this program is available in your area.
■
If you need further assistance in recycling, reusing, or trading in your “end of life” product, you may contact us
at the Customer Care number listed in your product’s user guide and we will be glad to help you with your
effort.
Finally, we suggest that you practice other environmentally friendly actions by understanding and using the
energy-saving features of this product (where applicable), recycling the inner and outer packaging (including
shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly.
With your help, we can reduce the amount of natural resources needed to produce electrical and electronic
equipment, minimize the use of landfills for the disposal of “end of life” products, and generally improve our
quality of life by ensuring that potentially hazardous substances are not released into the environment and are
disposed of properly.
www.gateway.com
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Notices
Copyright © 2005 Gateway, Inc.
All Rights Reserved
7565 Irvine Center Drive
Irvine, CA 92618-2930 USA
All Rights Reserved
This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or transmitted by any
means or in any form, without prior consent in writing from Gateway.
The information in this manual has been carefully checked and is believed to be accurate. However, changes are made
periodically. These changes are incorporated in newer publication editions. Gateway may improve and/or change products
described in this publication at any time. Due to continuing system improvements, Gateway is not responsible for inaccurate
information which may appear in this manual. For the latest product updates, consult the Gateway Web site at
www.gateway.com. In no event will Gateway be liable for direct, indirect, special, exemplary, incidental, or consequential
damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages.
In the interest of continued product development, Gateway reserves the right to make improvements in this manual and the
products it describes at any time, without notices or obligation.
Trademark Acknowledgments
1-800-GATEWAY, ActiveCPR, ALR, AnyKey, black-and-white spot design, CrystalScan, Destination, DestiVu, EZ Pad, EZ
Point, Field Mouse, Gateway 2000, Gateway Country, gateway.net, Gateway stylized logo, Perfect Scholar, Solo, TelePath,
Vivitron, stylized “G” design, and “You’ve got a friend in the business” slogan are registered trademarks and black-and-white
spotted box logo, GATEWAY, Gateway Astro, Gateway@Work, Gateway Connected touch pad, Gateway Connected music
player, Gateway Cyber:)Ware, Gateway Education:)Ware, Gateway Flex Case, Gateway Gaming:)Ware, Gateway GoBack,
Gateway Gold, Gateway Learning:)Ware, Gateway Magazine, Gateway Micro Server, Gateway Money:)Ware, Gateway
Music:)Ware, Gateway Networking Solutions, Gateway Online Network (O.N.) solution, Gateway Photo:)Ware, Gateway
Professional PCs, Gateway Profile, Gateway Solo, green stylized GATEWAY, green stylized Gateway logo, Gateway
Teacher:)Ware, Gateway Video:)Ware, HelpSpot, InforManager, Just click it!, Learn@Gateway, Kids BackPack,
SERVE-TO-ORDER, Server Watchdog, SpotShop, Spotshop.com, and Your:)Ware are trademarks of Gateway, Inc. Intel, Intel
Inside logo, and Pentium are registered trademarks and MMX is a trademark of Intel Corporation. Microsoft, MS, MS-DOS,
and Windows are trademarks or registered trademarks of Microsoft Corporation. All other product names mentioned herein
are used for identification purposes only, and may be the trademarks or registered trademarks of their respective companies.
www.gateway.com
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C:
www.gateway.com
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
menu 11
Numerics
5.25-inch drive
installing 39, 41
location 2
installing 47
reseating 47
retention levers 3
slot location 5, 47
interior 4
opening 30
CD
CD or DVD drive
A
accessories
add-in card
see card
administrator password
see supervisor password
Advanced menu
AMT 23
B
checkpoints
battery
replacing
troubleshooting 75
beep codes 76
bezel assembly
installing 36
removing 32
BIOS
resetting 68
settings 95
troubleshooting 79
updating 67
line 9
BIOS Setup utility
menus 66, 96
navigating through 66
opening 66
configuring
connections
settings 96
LAN 3
lock slot 3
monitor 3
submenus 102
troubleshooting 79
boot
mouse 3
network 3
parallel 3
device 11
www.gateway.com
113
Download from Www.Somanuals.com. All Manuals Search And Download.
power 3
RJ-45 3
serial 3
USB 2, 3
VGA 3
control panel
location 2
cover panel
DVD drive
removing 30
replacing 37
cover release latch
location 2
creating SUP CD 21
E
electronic specifications 93
D
expansion card
DDR SDRAM
see memory
device drivers
diagnostic LEDs
DIMM
F
fans
see memory
diskette drive
installing 39, 41
location 2
replacing 39, 41
troubleshooting 79
display
troubleshooting 84
documentation
Gateway Web site 6
drive bays
hard drive
location 2
drivers
installing 26
drives
CD 2, 39, 41
configuring 38
diskette 2, 39, 41
DVD 2
help
telephone support 86
tutoring 87
hot-swap
installing 38
power supply module 54
www.gateway.com
114
Download from Www.Somanuals.com. All Manuals Search And Download.
hot-swap drives
location 2
I
IDE
cables 39
drive configuration 38
indicators 2
LED 10
installing
key 2
add-in card 47
card 47
Main menu
maintenance
CMOS battery 59
expansion cards 47
fans 56
memory
map 93
modem
heat sink 51
media drive 39, 41
memory 45
PCI card 47
power supply module 54
processor 51
system board 61
interior
case 4
connection speed 83
monitor
Internet connection
interrupts 93
IRQ assignments 93
cleaning 17
port 3
J
motherboard
jacks
K
Kensington lock slot 3
keyboard
network jack 3
cleaning 17
port 3
troubleshooting 82
onboard RAID
configuring 42
onboard SATA RAID 42
L
LAN jack 3
www.gateway.com
115
Download from Www.Somanuals.com. All Manuals Search And Download.
opening case 30
operating system
setting up 13
P
parallel port 3
password
memory map 93
resetting BIOS 69
supervisor 19
user 19
ports
power
button 2, 10, 12
cord connector 3
indicator 2, 10
LED 2
line conditioners 9
protecting from surges 9
reset button 2
source problems 9
static electricity 29
troubleshooting 85
power supply
Security menu
uninterruptible 9
power supply module
installing 54
power/sleep LED 10
power-on self-test 11
processor
setting up
operating system 13
Setup utility
heat sink 51
installing 51
replacing 51
sparing
electronic 93
environmental 92
system board 91
starting server 10
static electricity 29
SUP CD
R
RAM
see memory
rear fan 3
removing
see installing
replacing
booting from 22
creating 21
www.gateway.com
116
Download from Www.Somanuals.com. All Manuals Search And Download.
supervisor password 19
Support 94
system 90
administration 19
control 19
management 19
security 19
specifications 90
startup 10
system board
components 5
installing 61
replacing 61
specifications 91
thumbscrew location 3
System Companion CD 26
system configuration
protecting with passwords 19
system interrupts 93
system recovery
UPS 9
T
USB ports
tape drive
cleaning 17
technical support
resources 86
telephone support 86
training
CD 87
troubleshooting
add-in card 80
battery 75
Web site
beep codes 76
BIOS 79
card 80
CD drive 79
CD or DVD 79
diskette drive 79
error messages 73
expansion card 80
general guidelines 75
general safety guidelines 72
www.gateway.com
117
Download from Www.Somanuals.com. All Manuals Search And Download.
www.gateway.com
118
Download from Www.Somanuals.com. All Manuals Search And Download.
|