ROUND DOLL CRIB
WITH CANOPY & BEDDING
Assembly Instructions.
Adult Assembly Required.
Read all instructions before use.
Save instructions for future use.
PRODUCT MODEL
NUMBER:
01906 - Pink Gingham
VERSION CODE:
1.0/0309/TG
Visit us online at www.badgerbasket.com
Toll-Free Customer Service: 1-800-236-1310 (Monday to Thursday 7:30 AM-4:30 PM CST)
Mail: PO Box 227, Edgar, WI 54426-0227 • Phone: 715-352-2311 • Fax: 715-352-3163
Page 1 of 4
1.0/0309/TG
Download from Www.Somanuals.com. All Manuals Search And Download.
D
D
B
B
A
D
D
B
B
F
PICTURE 1
STEP 1: See PICTURE 1. Attach the FOUR LEG
POSTS (B) to their designated spots on the TOP RING
(A) using the FOUR SCREWS (N).
Attach the FOUR DOWELS WITH TWO HOLES (D)
using FOUR SCREWS (N). The positions of these
four dowels may vary from shown in Picture 1.
PICTURE 2
STEP 2: See PICTURE 2. Turn the crib upside down.
Insert the FOUR LEG POSTS (B) through the large
holes on the BOTTOM RING (F) and slide the bottom
ring down until it rests on the DOWELS WITH TWO
HOLES (D).
Be sure screw and dowel holes on the bottom ring are
in the right place, and the white side of the bottom
platform is facing down (white side will face up when
the crib is in the upright position).
Starting at any dowel, work your way around the ring
and alternately screw down the FOUR DOWELS
WITH TWO HOLES (D) using FOUR SCREWS (N)
and insert the remaining ELEVEN DOWELS (D)
sandwiched between the top and bottom rings.
G
G
There is one hole for the canopy pole that you will
leave open.
G
STEP 3: See PICTURE 3. Turn the crib right side up.
Insert the FOUR CASTER WHEELS (G) into the
holes on the bottom of the LEG POSTS (B). Grasp
each leg and gently but firmly press each wheel
against the floor to snap it into place.
G
PICTURE 3
Page 3 of 4
1.0/0309/TG
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE 4A
PICTURE 4B
I
I
Your fabric color/pattern
may vary from shown.
H
H
PICTURE 5
M
K, L
J
STEP 4: See PICTURES 4A and 4B. Insert the CANOPY POLE (H) through the hole on the TOP RING (A)
and push it down until it rests in the hole on the BOTTOM RING (F). Insert the two free ends of the METAL
CANOPY FRAME (I) into the top of the CANOPY POLE (H). You may need to gently tap on the canopy frame
with a hammer so that the ends are pushed down into the pole as far as possible (see PICTURE 4B).
Starting by the canopy pole, wrap the FABRIC SKIRT (J) around the BOTTOM RING (F) pressing the grip
tape together. When you get back to where you started, press the grip tape on the two ends of the skirt together.
Put the FABRIC SHEET (K) on the MATTRESS PAD (L) and place the sheet and pad into the crib.
STEP 5: See PICTURE 5. Position the FABRIC CANOPY (M) over the METAL CANOPY FRAME (I).
Secure the grip tape tabs on the fabric canopy around the metal frame. Adjust the canopy so it drapes around the
crib.
CARE INSTRUCTIONS:
Wipe crib parts and vinyl pad clean with a damp cloth and mild detergent as needed.
Fabric is poly/cotton. For longevity of the product we recommend hand washing the
bedding; however it can be machine washed cold on gentle and air dried or tumble
dried on low or no heat. Iron on the lowest setting for poly/cotton.
Page 4 of 4
1.0/0309/TG
Download from Www.Somanuals.com. All Manuals Search And Download.
|