Baby Trend Baby Playpen PY90973 User Manual

Read all instructions BEFORE assembly and USE of product.

KEEP INSTRUCTIONS FOR FUTURE USE.

Item#: PY90973

Check that you have all the below parts for this model

before assembling the playard.

Nursery Center

Close N Cozy (Type C)

Soft Goods x 1

Strap Set x 1

Playard (fully assemble) x 1

Mattress x 1

Changing Table x 1

Mattress Support Bar x 2

Lower Bar x 2

Long Curved Bar x 2

Short Bar with Connector Knob x 2

Music Center x 1

Center Cross Bar x 1

Upper Back Bar x 1

Upper frame x 2

Side frame x 2

Leg x 4

Screw x 4

---------------------------------------------

Travel / Storage Bag x 1

Mini Playard

This unit does not equipped with basket, bassinet, mobile,

parent organizer and canopy.

IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT,

PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT

1-800-328-7363 BETWEEN THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC

STANDARD TIME FOR ASSISTANCE. PLEASE HAVE YOUR MODEL NUMBER AND

MANUFACTURING DATE AVAILABLE WHEN YOU CALL. THIS INFORMATION CAN BE

FOUND ON A SMALL STICKER UNDER THE PLAYARD.

Instruction Manual

Convenience through innovation and thoughtful design

04.09

Baby Trend, Inc.

1607 S. Campus Ave., Ontario, CA 91761

1-800-328-7363 (8:00am ~ 4:30pm PST)

or online http://www.babytrend.com

Convenience through innovation and thoughtful design

www.babytrend.com

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS

ASSEMBLY

TO ASSEMBLE PLAYARD

IMPORTANT!To ensure safe operation of your playard,

please follow these instructions carefully. Please keep these

instructions for future reference.

IMPORTANT! Before assembly and each use, inspect this

product for damaged hardware, loose joints, missing parts or sharp

edges. NEVER use if any parts are mssing or broken.

IMPORTANT!Adult assembly is required.

Mattress

Playard

This model may not include some features shown below. Check the parts list to make sure

you have all the parts for this model before assembling the playard.

ATTENTION:

Playard must be fully assembled and securely

locked before installing or using other accessories.

1. Unzip bag and remove Playard frame (Fig. 1).

Undo the three (3) Fasten straps and set the

Mattress aside (Fig. 2).

Fig. 1

2. Turn the Playard right side up and keep the

Legs and Wheels close together. Stretch out

top of Playard and pull up one side at a time of

each of the top rails until each latch “Clicks”

and locks securely into place (Fig. 3).

Metal Support Tubes

(2 male, 2 female)

Bassinet

Playard

NOTE: The best way to lock the rail(s) is to

hold one hand on each side and pull up sharply.

(DO NOT pull from the middle where the latch

release is located).

Fig. 2

Long Curved Bar (2)

IMPORTANT: The handle located in the center

of the Playard ﬂoor MUST remain raised

(Approx. 45.7 cm or 18 inches) while locking

the side rails in place. If the center is not raised

the rails will NOT lock.

Short Bar with Connector

Knob (2)

Changing Table

Mattress

If you experience difﬁculty and one side of the

rail will lock but the other side will not then,

unlock the rail by squeezing the release in the

center and try again. If you still have difﬁculty,

contact our Customer Service Center at

1-800-328-7363 or visit us online at

Fig. 3

sleep play nature

mp3

input

www.babytrend.com.

Fixed Mobile

Music Center

Travel / Storage Bag

Parent Organizer*

Fig. 4

* Type may vary

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

3. To operate the brakes on the Wheels, press

downward on the brake levers. To release, lift

upward on the lever (Fig. 4)

FOLDING PLAYARD

1. Undo the three (3) hooks and loop straps

holding the Mattress from underneath the

Playard ﬂoor or remove the Mattress for the

Bassinet and set aside.

4. Once all four (4) top rails are locked in place,

push down on the center handle (Fig. 5). The

center mechanism will rotate clockwise 90

degrees and automatically lock in place.

Rotate before

lifting

2. Grasp the center handle, push down and rotate

the handle counter-clockwise 90 degrees and

lift upward until the handle is as high as the top

rails (Fig. 10). Gather the Legs and Wheels

together towards the center as close as possible

so that they nearly touch (Fig. 11).

Fig. 10

Fig. 5

IMPORTANT: Test each top rail by pushing

down slightly to conﬁrm each is rigid and

locked securely in place before use (Fig. 6).

NOTE: The top rails of the Playard are sill in

the “Locked” position.

ATTENTION:

To use as a bassinet, skip to page 8 for bassinet

installation instructions.

Fig. 11

3. Locate the rail release lever in the center and

bottom side of each rail. Lift slightly while

squeezing the lever until the rail “Clicks” and

releases. Push down each side of the rail while

still holding the release lever until both sides

are down. Repeat for all remaining sides

(Fig. 12).

Fig. 6

NOTE: If the top rail(s) do not release

completely, DO NOT FORCE! Check the

ﬂoor of the Playard to make sure all the bottom

rails are unlocked and make sure the middle

handle is pulled up and has not fallen back

down. If so, repeat step #3.

Fig. 12

5. Place the Mattress on the ﬂoor of the Playard

with the padded side facing up (Fig. 7)

Fig. 7

4. Gather four (4) corners and center all together

tightly (Fig. 13).

5. Wrap Mattress around Playard frame with

padded side facing inward.

Fig. 13

6. Feed the three (3) hook and loop straps located

on the underside of the Mattress through the

slots in the ﬂoor of each end of the Playard

(Fig. 8). Fasten the hook and loop straps to the

underside of the Playard ﬂoor to prevent the

Mattress from moving (Fig. 9).

6. Secure the three (3) hook and loop straps by

feeding them through the loops on the end

of the Mattress and folding them back onto

themselves (Fig. 14).

Fig. 8

7. Place folded Playard into carry bag so that the

handle comes through the opening between

each side of the zipper.

Fig. 9

Fig. 14

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

ASSEMBLY

ACCESSORIES

TO ASSEMBLE BASSINET

WARNING:Failure to follow these warnings and the

instructions could result in serious injury or death.

FALL HAZARD:To help prevent falls, do not use this

product when the infant begins to push up on hands and knees or

has reached the height of 25 in. (635 mm), weight of 15 lbs. (6.8 kgs)

or 4 months old, whichever comes ﬁrst.

Metal Support Tubes

(2 male, 2 female)

Bassinet

SUFFOCATION HAZARD:Infants can suffocate

• In gaps between an extra pad and sides of the bassinet/cradle

• On soft bedding

Never add a mattress, pillow, comforter, or padding.

Use only the pad provided by manufacturer.

Never use a water mattress with this product.

ATTENTION:

Playard must be fully assembled and securely

locked before installing or using the bassinet

feature. (See To Assemble Playard section)

You will need to remove the mattress from the

bottom of the Playard to use inside your Bassinet.

• To reduce the risk of SIDS, pediatricians recommend healthy infants be

placed on their back to sleep, unless otherwise advised by your physician.

• The playard, including side rails, must be fully erected prior to use. Make

sure each latch is secure.

• Strings can cause strangulation! NEVER place items with a string around

a child's neck such as hood strings or paciﬁer cords. NEVER suspend

strings over bassinet or attach strings to toys.

• Discontinue use of the bassinet or the changing table when child begins to

push up on hands and knees or has reached the height of 25 in. (635 mm),

weight of 15 lbs. (6.8 kgs) or 4 months old, whichever comes ﬁrst.

1. Position the Bassinet over and down into the

fully assembled Playard. Secure in place by

pushing down ﬁrmly on each plastic support

clip until all are snapped into place (Fig. 15).

Fig. 15

Fig. 16

2. Assemble Mattress Support Tubes (if

equipped; otherwise, skip to step 4) by

inserting the two (2) male tubes into the two

(2) female tubes (Fig. 16).

• NEVER place product near a window where cords from blinds or drapes

can strangle a child.

• Always provide the supervision necessary for the continued safety of your

child. NEVER leave child unattended.

3. Insert both, assembled, Mattress Support

Tubes into the loops provided on the bottom

of the Bassinet (Fig. 17).

• NEVER use plastic shipping bags or other plastic ﬁlm as mattress covers

not sold and intended for that purpose. They can cause suffocation.

4. Place the Mattress into the Bassinet with the

padded side facing upward (Fig. 18)

• Use bassinet with only one child at at time.

• NEVER place a child under the bassinet.

• NEVER store the bassinet in the playard while in use.

• The bassinet must be fully assembled and installed before using.

Fig. 17

NOTE: Fasten tabs underneath the Mattress

secure it in place.

• STRANGULATION HAZARD: NEVER leave the changing table

in place when the child is in the bassinet or the playard. Always ﬂip

changing table down while not in use.

• To prevent your child from falls and other injuries, always use safety belt

when child is on the changing table, always stay within arm's reach of

your child when using the changing table.

• To help prevent heat build-up inside the playard and to avoid overheating

your child, when using the bassinet NEVER use an outdoor canopy.

TO REMOVE BASSINET

1. Remove Mattress from Bassinet.

2. Remove Canopy.

3. Unsnap all clips and lift Bassinet.

Fig. 18

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

MOBILE ASSEMBLY (Fixed)

TO ASSEMBLE CHANGING TABLE

ATTENTION: DO NOT attach Mobile to Canopy until Canopy is correctly installed

as noted in the Canopy instructions.

A crib mobile is intened for visual stimulation and is not intended to be grasped by the child.

If attached to the crib or playpen, remove when baby begins to push up on hands and

knees. If so designed, mount on wall or ceiling clearly out of a standing baby's reach.

Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to a crib or

playpen according to the instructions. Check frequently.

(a)

(b)

DO NOT add additional strings and straps to attach to a crib or playpen.

DO NOT attach the Mobile with child in Playard or Bassinet.

DO NOT remove the Mobile before retracting the Canopy or removing the Canopy.

(c)

WARNING

Fixed Mobile

FALL HAZARD: To

prevent death or serious injury,

always keep child within arm's

reach.

(c)

Fig. 23

(a)

Always use restraint belt to prevent

falls, see page 15 for details.

(e)

(d)

(b)

Contents:

(a) 2 Long Curved Bars

(b) 2 Short Bar with Connector Knobs

Contents:

(a) 1 Mobile Lower Arm

(b) 1 Mobile Arm Holder

(d) 1 Mobile Tri-shaped Arm

(e) 3 Toys (toys may vary)

(c)

(a)

(b)

(a)

(b)

ATTENTION:

Fig. 24

Playard must be fully assembled and securely

locked before installing or using the changing

table feature. (See To Assemble Playard section)

Fig. 19

1. Insert the Mobile Lower Arm (a) into the

Mobile Arm Holder (b) untill locked together

(Fig. 19).

Fig. 20

(d)

1. Connect the two (2) Long Curved Bars

together (Fig. 23).

2. Insert the Mobile Upper Curved Arm (c) into

the Mobile Lower Arm (a, b) until locked

together (Fig. 20).

2. Insert the assembled curved bars into the

Changing Table fabric (Fig. 24) Slide the

Curved Bars around inside sleeve of the

Changing Table.

(e)

Fig. 25

Fig. 21

3. Snap the Mobile Tri-shaped Arm (d) onto the

end of the Upper Curved Arm (a, b, c)

(Fig. 21). Connect each of the three Toys (e)

to the Mobile by threading the string into the

slot at the end of each arm.

3. Connect the two (2) Short Bars to each end

of the Long Curved Bar (Fig. 25) Make sure

that the knobs are both facing down and the

same direction on each end. (Fig. 26)

4. Insert the bottom of the Mobile Arm into the

frame of the Playard (Fig. 22).

Fig. 26

Fig. 22

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

4. Insert Connector Knob Prongs into holes

located on both corners of the Playard

(Fig. 27).

To remove changing table

Flip Changing Table to the outside of the Playard.

Unsnap fabric ﬂap of Changing Table from

Playard. Twist Connector Knobs clockwise to

unlock. (Fig. 33) Remove Changing Table from

Playard (Fig. 34) and disconnect the Short Bars

from the Curved Bar by pressing on the snap

buttons and pulling apart. Remove Curved Bar

from Changing Table sleeve.

Fig. 27

Fig. 33

5. Turn the Connector Knobs counter clockwise

to lock into place (Fig. 28).

Fig. 28

Fig. 34

6. Flip Changing Table over onto Playard

(Fig. 29).

PARENT ORGANIZER ASSEMBLY

7. Snap the two (2) buttons on the ﬂap down

onto the Playard (Fig. 30.

Fig. 29

Parent Organizer

Diaper Stacker

IMPORTANT: Check that the Changing Table

is correctly and securely installed BEFORE

each use.

1. Parent Organizer: Position each hook so that

the hooked end is facing the rear side of the

organizer. Press the hook down ﬁrmly into the

slot until it snaps into place. (Fig. 35)

Fig. 30

To use changing table

restraint system

Diaper Stacker: Skip to step 2.

2. Connect the Parent Organizer/Diaper

Stacker to the Playard by sliding the two (2)

connecting clips over an open portion of the

top rail of the Playard. (Fig. 36)

1. Place child on changing table, make sure hand

and arms are clear of the restraint. Bring the

restraint around the child's waist and clip the male

and female ends of the buckle together. (Fig. 31)

Fig. 35

Fig. 31

2. Tighten strap until ﬁts snug around child's

waist. DO NOT OVER TIGHTEN. (Fig. 32)

NOTE: The Parent Organizer/Diaper Stacker

can only be installed on open sides of the

Playard where the connecting clips can easily

be attached without interfering with other

features.

3. To remove, unsnap the buckle.

ATTENTION:

NEVER use changing table if it is damaged or

broken.

Fig. 32

Fig. 36

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Recording Indicator

To listen to NATURE sounds, press the

NATURE button you may use the previous /

next button to change the sound. The Vol

WARNING: Keep batteries out of children's reach. Old and

new batteries should not be mixed. Alkaline, standard carbon-zinc, and

rechargeable nickel-cadium batteries should not be mixed. Remove

batteries before storing music center for a long period of time.

or Vol

buttons control the unit's volume.

VIBRATION: To use the vibration button

press down once to active the speed, press

again for a Medium speed and once more for

the faster speed. Press to reduce the speed.

Voice Activation

Indicator

MUSIC CENTER

NIGHT LIGHT: To use the night light, press

the button. The light has 3 settings of

brightness and is controlled by the button.

The Music Center is designed to be attached to

the playard corners. It can be attached on the

Changing Table's side or the Canopy's side. See

ﬁgure 37.

MP3 Indicator

VOICE RECORDER: To use the Voice

record function press the button and

speak into the microphone to record your 10

second voice message. Press to hear the

message.

VOICE ACTIVATION: To use the Voice

Activation function press the button twice

if the unit is power off. If the unit is already

power on, press the button once. The

voice activation light will be illuminated

when in voice activation mode. If your infant

cries his/her voice will activate the sleep

music to come on and play. When voice

activation is enabled, sleep mode is active for

2 hrs.

Fig. 37

MUSIC OPERATION

The Music Center requires 4 AA batteries. Please

see ﬁgure 38 for battery installation. Unscrew

the battery door screws and pull outward on the

battery door. Install batteries as shown. Re-install

battery door and secure with screws.

MP3 FUNCTION: Use the input jack to

attach your MP3 player into the unit

Press the button to select the MP3 input.

Your MP3 music will then be played through

the unit and will over-ride the unit’s music.

To listen to the unit’s music, depress the

button. Volume will be controlled by the MP3

player.

Fig. 38

To active the unit, press the on/off button.

Press button a second time to switch unit off.

To listen to SLEEP music, press the SLEEP

button. You may use the previous / next

button to change the song. The Vol

Vol buttons control the units volume.

To listen to PLAY music, press the PLAY

button. You may use the previous / next

button to change the song. The Vol or

Vol buttons control the unit's volume

Download from Www.Somanuals.com. All Manuals Search And Download.

Actiontec electronic Network Router HSP56I User Manual
ADTRAN Network Card T200 T1 HDSL4 User Manual
Aiphone Amplified Phone PG 10A User Manual
Aiwa CD Player CX NMT50 User Manual
Amana Refrigerator ASD2624HEQ User Manual
Amana Refrigerator W10211588A User Manual
American Standard Plumbing Product 2555602 User Manual
Avenview Switch SW HDSDI 8X1 User Manual
Bacharach Carbon Monoxide Alarm Gas Leak Detection User Manual
Beko Refrigerator CXFD5104 W User Manual