Avital Remote Starter 6501 User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
AviStart 6501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Remote Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Stealth Coding Technology. . . . . . . . . . . . . . . . . . . . . . . 3  
Electronic Scan Prevention (ESP). . . . . . . . . . . . . . . . . . . . . 3  
Instant Remote Control Code Deletion. . . . . . . . . . . . . . . . . . 3  
One-Step Remote Control Code Learning . . . . . . . . . . . . . . . . 3  
Valet Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Operating Your AviStart . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
To Arm The System . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Remote-Controlled Silent Arm/Disarm . . . . . . . . . . . . . . . . . 4  
User-Programmable Long-Term Silent Arm/Disarm . . . . . . . . . . . 4  
Two-Stage Unlock Capability . . . . . . . . . . . . . . . . . . . . . . 5  
Remote Panic with Safety Locks . . . . . . . . . . . . . . . . . . . . 5  
Interior Light Illumination . . . . . . . . . . . . . . . . . . . . . . . . 5  
User-Programmable Passive Door Lock . . . . . . . . . . . . . . . . . 5  
User-Programmable Ignition-Controlled Door Lock/Unlock . . . . . . . 5  
User-Programmable RPM Door Lock . . . . . . . . . . . . . . . . . . 6  
Protected Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Remote-Controlled Valet. . . . . . . . . . . . . . . . . . . . . . . . . 6  
LED System Status Indicator . . . . . . . . . . . . . . . . . . . . . . . 7  
Remote-Controlled Trunk Release Capability . . . . . . . . . . . . . . 7  
Remote-Controlled Accessory Outputs . . . . . . . . . . . . . . . . . 7  
Zone2 ™ Impact Sensor . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Remote-Controlled Sensor Bypass . . . . . . . . . . . . . . . . . . . . 8  
Previous Intrusion Alert . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Specific Zone Intrusion Identification . . . . . . . . . . . . . . . . . . 8  
User-Programmable Door Ajar Indication . . . . . . . . . . . . . . . . 8  
User-Programmable Siren Duration . . . . . . . . . . . . . . . . . . . 9  
Alarm State Memory . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Automatic Malfunction Override . . . . . . . . . . . . . . . . . . . . 9  
Remote Engine Start - Safety and Counter-Theft. . . . . . . . . . . . . 1 0  
Remote Engine Start - Operation . . . . . . . . . . . . . . . . . . . . 1 1  
User-Programmable Temperature-Controlled Starting. . . . . . . . . . 1 2  
Pit Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3  
User-Programmable Features . . . . . . . . . . . . . . . . . . . . . . . 1 4  
Programming Table for System Features . . . . . . . . . . . . . . . . 1 5  
Programming Table for Remote Controls . . . . . . . . . . . . . . . . 1 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AviStart 6501  
Congratulations! You have just purchased the AviStart 6501, a remote engine  
starter and security system manufactured by Avital Technologies, Inc. You are  
about to experience the convenience and luxury of being able to start your  
vehicle engine from the comfort of your home, office, department store or  
other remote location.  
To fully benefit from the capabilities of your AviStart system, we encourage  
you to read the Owner’s Manual thoroughly before using the system. If you  
have any problems or questions regarding your AviStart system, consult the  
dealer from whom you purchased this product. To locate an authorized Avital  
dealer, contact Customer Service directly at 1-800-824-3208 (toll-free within  
the U.S.) or 1-818-709-7551.  
Lifetime Warranty  
Avital guarantees the operation of your AviStart control unit and remote  
controls for as long as you own your car. (Please refer to back of this manual  
for complete information.)  
Remote Controls  
Included with your AviStart system are two AviGlo™ 4-button/9-channel  
remote controls. Once exposed to light, the AviGlo remote control buttons  
will glow, making the buttons visible in the dark.  
The remote control (remote) is a miniature transmitter powered by a small  
+12 volt battery. The RangeMaster™ super-heterodyne receiver (installed in  
your vehicle) allows your remote to command your system from up to  
¼ mile away. Obstructions, electrical or radio interference, weather  
conditions, window tint or a weak battery can reduce this range. Your remote  
is the key to your AviStart system and can be used to arm and disarm your  
alarm, lock and unlock your doors, "pop" your trunk, start your engine and  
control optional accessories.  
The AviStart system can accept up to four Avital remote controls. Additional  
remote controls and remote control batteries can be purchased from any  
authorized Avital dealer, or by calling Customer Service at 1-800-824-3208  
(toll-free within the U.S.) or 1-818-709-7551.  
2
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stealth Coding Technology  
Stealth Coding technology offers the most advanced protection available  
against "code-grabbing" devices which thieves may use to record the digital  
code transmitted by your remote control. When you leave the area, thieves  
can then play back the code to unlock the doors and deactivate your system.  
Avital's remote controls with Stealth Coding randomly change the code every  
time you use them, and your system will not respond if any code is  
retransmitted. This technology makes code-grabbing devices useless.  
Electronic Scan Prevention (ESP)  
Your AviStart system also includes ESP, which blocks electronic scanner codes  
preventing unauthorized operation of your system.  
Instant Remote Control Code Deletion  
In the event of a lost or stolen remote control, all remote controls can be  
erased from the system's memory preventing unauthorized system operation.  
(See the "Programming Table for Remote Controls" on page 16).  
One-Step Remote Control Code Learning  
The AviStart system allows you to add new remote controls in one step. (See  
the "Programming Table for Remote Controls" on page 16).  
Valet Switch  
The valet switch is a small hidden toggle switch which allows you to control all  
of the system's programmable features. (See "User-Programmable Features" on  
page 14). This switch can only be controlled with the use of your ignition key.  
NOTE: Be sure to have your dealer show you where the valet switch is located.  
3
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your AviStart  
To Arm The System  
The alarm can be programmed for active or passive arming. Active arming  
means the alarm can only be armed by the remote control. Passive arming  
means the alarm will automatically arm itself. See the "Programming Table for  
System Features" on page 15.  
Active Arming  
Press the A button on your remote control for 1-2 seconds. The siren will  
chirp twice, the parking lights will flash twice, the doors will lock, the LED  
will flash slowly and the starter will be disabled.  
Passive Arming  
Turn the ignition key "OFF," exit the vehicle and close the doors. When the  
interior lights turn off, the LED will begin flashing rapidly to indicate the alarm  
is passive arming. After 30 seconds, the siren will chirp twice, the parking  
lights will flash twice, the LED will flash slowly and the starter will be disabled  
(at any time during passive arming, the alarm can be actively armed).  
To Disarm the System  
Press the A button for 1-2 seconds. The siren will chirp once, the parking  
lights will flash once, the doors will unlock, the interior lights will turn on, the  
LED will turn off and the starter will be enabled.  
Remote-Controlled Silent Arm/Disarm  
Press theH button for 1-2 seconds toarm or disarm your system without the  
usual siren chirps.  
Silent Arm Indications  
The parking lights will flash twice, the doors will lock, the starter will be  
disabled and the LED will flash slowly.  
Silent Disarm Indications  
The parking lights will flash once, the doors will unlock, the starter will be  
enabled and the LED will turn off.  
User-Programmable Long-Term Silent Arm/Disarm  
This feature allows you to completely disable the arm/disarm siren chirps until  
you decide to restore them. (See the "Programming Table for System Features"  
on page 15.)  
4
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Two-Stage Unlock Capability  
If the optional Two-Stage Unlock feature was installed, press the A orH  
button for 1-2 seconds and only the driver door will unlock. Within 3  
seconds, press the A or H button again and the passenger doors will unlock  
(may require an optional relay).  
Remote Panic with Safety Locks  
In a threatening situation, you can activate Remote Panic with Safety Locks.  
When activated, the siren will sound and the parking lights will flash. If you  
are inside your vehicle and the ignition key is "ON," the doors will lock. If you  
are outside the vehicle with the ignition key "OFF," the doors will unlock.  
To Activate  
1. Press the A button for 3-4 seconds.  
2. The siren will sound and the parking lights will flash.  
3. If the ignition key is "OFF," the doors will unlock. If the ignition key is  
"ON," the doors will lock.  
To Deactivate  
1. Press the A button for 1-2 seconds.  
2. The siren will shut off and the parking lights will stop flashing.  
Interior Light Illumination  
When the alarm system is remotely disarmed, the vehicle interior light(s) will  
turn on for 30 seconds or until the ignition key is turned on.  
User-Programmable Passive Door Lock  
The system will not automatically lock the doors when the alarm passively  
arms to prevent the keys and remote from being locked in the vehicle. If you  
prefer, you can easily program the alarm to automatically lock the doors every  
time the alarm passively arms. (See the "Programming Table for System  
Features" on page 15.)  
User-Programmable Ignition-Controlled Door Lock/Unlock  
For the ultimate in security and convenience, the AviStart is programmed to  
automatically lock your doors when the ignition key is turned "ON" or the  
engine is started, and will unlock when the ignition key is turned "OFF." This  
feature can be programmed ON or OFF. (See the "Programming Table for  
System Features" on page 15.)  
5
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User-Programmable RPM Door Lock  
The system can be programmed to automatically lock the doors when the  
engine reaches the factory preset RPM level. (See the "Programming Table for  
System Features" on page 15). When you begin driving, your vehicle doors  
will automatically lock. When you turn the ignition key off, the doors will  
automatically unlock.  
NOTE: Ignition-Controlled Door Lock feature must be programmed OFF.  
Protected Valet Mode  
You should place your system in Protected Valet Mode whenever your vehicle  
is being serviced by mechanics, car wash personnel or driven by valet parking  
attendants. While in the Protected Valet Mode, all remote starter and alarm  
functions are bypassed to prevent unauthorized or accidental operation. If a  
remote start is attempted, the parking lights will flash 4 times and the vehicle  
will not start. Remote-controlled door lock/unlock , trunk release and all  
optional accessories will still operate.  
To Turn on Protected Valet Mode  
1. Turn the ignition key to the "ON" position or start the engine.  
2. Flick the valet switch to the "ON" position.  
3. The LED will turn on solid red to indicate the system is in the Protected  
Valet Mode.  
4. Turn the ignition key to the "OFF" position.  
To Turn off Protected Valet Mode  
1. Turn the ignition key to the "ON" position or start the engine.  
2. Flick the valet switch to the "OFF" position.  
3. The LED will turn off to indicate the system is no longer in the Protected  
Valet Mode.  
4. Turn the ignition key to the "OFF" position.  
Remote-Controlled Valet  
For your convenience, the system can be put into Valet Mode via the remote  
control. While in Remote-Controlled Valet, all alarm functions are bypassed.  
Remote start, remote-controlled lock/unlock and all optional accessories will  
still operate.  
NOTE: The system must be disarmed in order to activate the  
Remote-Controlled Valet feature.  
6
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To Activate Remote-Controlled Valet  
1. Press the A and s buttons at the same time for 1-2 seconds.  
2 . The parking lights will flash 4 times, and the LED will turn on solid red.  
To Deactivate Remote-Controlled Valet  
1. Press the A and s buttons at the same time for 1-2 seconds.  
2 . The parking lights will flash 3 times and the LED will turn off.  
LED System Status Indicator  
The LED on your vehicle dashboard or center console will inform you of the  
system status.  
LED  
Off  
Status  
System is disarmed  
On solid  
In Protected Valet Mode  
System is armed  
Slow flash  
Flashing in cycles  
Rapid flash  
See "Specific Zone Intrusion Identification" on page 8  
Passive arming  
Remote-Controlled Trunk Release Capability  
If you had the optional Trunk Release feature installed, simply press the  
d button for 1-2 seconds to activate your vehicle electronic trunk release.  
The trunk will "pop" open. This feature will only work if your system is  
disarmed (may require an optional relay).  
Remote-Controlled Accessory Outputs  
These outputs allow you to add optional remote-controlled accessories to your  
system such as a window roll-up, garage door opener or fuel door release. To  
activate your optional accessories, see the "Programming Table for Remote  
Controls" on page 16.  
Zone 2 ™ Impact Sensor  
The Zone 2 Impact Sensor has two individual vibration/impact sensing zones.  
Zone #1:  
If a less threatening vibration or impact is detected, the siren will issue 2  
warn-away chirps. A second violation will also issue 2 warn-away chirps. If  
within 45 seconds a third violation is detected, the sensor will automatically  
trigger the alarm. The siren will sound and the lights will flash.  
7
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Zone #2:  
If a more threatening vibration or impact is detected at any time, the siren and  
lights will activate instantly.  
Remote-Controlled Sensor Bypass  
You can bypass the system sensor(s) at any time. The alarm system will still  
provide full perimeter protection.  
To Bypass the Sensor(s):  
1. Press remote H and d buttons at the same time.  
2. The siren will chirp twice...pause...chirp twice...pause...chirp twice.  
3. The sensor(s) is now bypassed until you remotely disarm and then rearm  
your system.  
Previous Intrusion Alert  
If the vehicle had been tampered with and the alarm has been triggered, the  
siren will chirp 3 times upon remote disarm instead of the usual 1 chirp.  
Specific Zone Intrusion Identification  
If the alarm had been triggered in your absence, the siren will chirp 3 times  
upon remote disarm (Previous Intrusion Alert). When you enter the vehicle  
and turn the ignition "ON," the LED will flash in cycles to specifically identify  
which zone triggered the alarm.  
LED  
1 flash...1 flash...  
Zone  
Impact sensor / optional sensor input  
Hood trigger  
2 flashes...2 flashes...  
3 flashes...3 flashes...  
4 flashes...4 flashes...  
Door trigger  
Trunk trigger  
User-Programmable Door Ajar Indication  
When you remotely arm the alarm system and a door is ajar (not closed), the  
siren will chirp 2 times, then chirp 3 times and the parking lights will flash 3  
times. This feature provides audible and visual indication to prevent battery  
drain. (See "Programming Table for System Features" on page 15.)  
NOTE: If your vehicle has factory delayed lighting, this feature will be  
turned OFF.  
8
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User-Programmable Siren Duration  
Upon activation, the siren can be programmed to run for 30 or 60 seconds  
before it will shut off and instantly rearm. ( See the "Programming Table for  
System Features" on page 15.)  
Alarm State Memory  
If your vehicle battery is disconnected and later reconnected, the system will  
automatically return to its last state before power was removed, whether it was  
armed, disarmed or in a valet mode. For example, if a mechanic disconnects  
the battery while the alarm is disarmed or in a valet mode, he won't trigger the  
alarm when he reconnects the battery. If a thief removes power while the  
alarm is armed, and reconnects it, the alarm will instantly sound, the parking  
lights will flash and the starter will be disabled.  
Automatic Malfunction Override  
In the event of a faulty sensor or alarm input trigger zone, the alarm, when  
remotely armed, will alert you by a series of chirps and parking light flashes.  
How to Interpret the Chirps and Parking Light Flashes  
When you press the remote control buttons, the system will respond with  
chirps and flashes of the parking lights to indicate the system status. An  
explanation of these chirp/flash acknowledgments is listed below and on the  
following page.  
Number of chirps and flashes  
1 chirp, 1 flash  
Explanation  
Disarming of the alarm.  
Arming of the alarm.  
2 chirps, 2 flashes  
2 chirps and flashes, then 3 more chirps  
and flashes  
Armed and a door is ajar.  
2 chirps and flashes, then 4 more chirps  
and flashes  
Armed and there is a sensor malfunction  
(automatically bypassed).  
3 chirps, 3 flashes  
4 chirps, 4 flashes  
0 chirps, 1 flash  
Disarmed and there was an intrusion attempt.  
Armed and there is a trigger malfunction  
(automatically bypassed).  
Remote start attempt and a fault was detected.  
Remote start attempt and all zones are OK. The  
vehicle will start.  
0 chirps, 2 flashes  
9
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Number of chirps and flashes  
Explanation  
2 three-second flashes  
or 1 three-second flash  
Remote automatic temperature-controlled  
starting. 2 = activation, 1 = deactivation.  
0 chirps, 4 light flashes  
0 chirps, 3 light flashes  
6 chirps, 0 light flashes  
Remote valet activation.  
Remote valet deactivation.  
Remote sensor bypass.  
2 chirps and flashes, then 3 more chirps  
and flashes  
Armed and a door is open or ajar.  
Remote start attempt and system is in  
Protected Valet Mode.  
0 chirps, 4 light flashes  
Remote Engine Start - Safety and Counter-Theft  
CAUTION : Be sure to read the "WARNING" bulletin on the inside  
cover of this manual before attempting to operate remote start.  
I
Automatic Safety and Counter-Theft Features  
Before remote starting your engine, the AviStart system will automatically  
perform a safety check to ensure the following conditions have been met:  
• Brake pedal is not depressed.  
• Engine and ignition are turned "OFF."  
• Hood is closed.  
After remote starting your engine, the AviStart system will shut off the engine  
immediately if the ignition is "OFF" and any of the following occurs:  
• The hood is opened.  
• The brake pedal is pressed.  
• The alarm is triggered.  
• The remote controls button is pressed.  
• The 20 or 30 minute programmable run time expired.  
Visual Fault Indication  
The AviStart has a built-in fault detection system that automatically scans all of  
the safety zones, prevents the system from remote starting and provides a  
visual indication if a fault is detected. The parking lights will flash 1 time if the  
hood is opened or if the brake pedal is depressed and will not allow the  
engine to start. If this occurs, bring your vehicle to your authorized Avital  
dealer for service.  
10  
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Engine Start - Operation  
Your AviStart system will start your vehicle engine with a touch of a button on  
your AviGlo™ remote control. To cool or warm the interior of your vehicle  
before you enter, set the climate control to your preference (heater, defrost or  
air conditioning) before remote starting. Set the fan to a medium speed(not  
maximum). Ensure the vehicle is in "Park" and the key is not in the ignition.  
We strongly recommend that you arm the alarm system at all times, especially  
if you are going to remote start the vehicle.  
To Remote Start the Engine:  
1. Press the remote controls button for 1-2 seconds, 10-15 minutes before  
you enter your vehicle (this will allow the climate control time to heat or  
cool the interior.) The parking lights will flash 2 times, the engine will start  
and the parking lights will remain on as a visual indication that the engine  
is running. Five seconds after the engine starts, the doors will  
automatically lock. If you do not want the doors to automatically lock  
upon remote start, this feature (Security Start Locks™) can be programmed  
OFF. (See the "Programming Table for Systems Features" on page 15.)  
If you have a diesel engine, the AviStart will be programmed to start 15  
seconds after the parking lights flash 2 times or after the vehicle glow plug  
light has turned off. This will allow time for the glow plugs to heat up. The  
alarm system will remain armed.  
2. If the engine does not remote start, the AviStart system will attempt to start  
the engine two additional times.  
3 . If the vehicle is left unattended, the engine will run for 20 minutes and  
then shut off automatically. You can also program the system to run the  
engine for 30 minutes. (See the "Programming Table for System Features"  
on page 15.)  
To Operate the Vehicle While Remote Started:  
1. If the alarm system is armed, press the remote A button for 1-2 seconds.  
The alarm will disarm and the doors will unlock.  
2. Enter the vehicle (do not touch the brake pedal), turn the ignition key to  
the "ON" position and then press the brake pedal. Pressing the brake pedal  
will shut off the remote start and parking lights but the engine will remain  
running.  
3. You can now drive the vehicle.  
11  
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To Shut Off Remote Start:  
At any time while the engine is remote started, you can shut off the engine  
with the remote control by pressing the remote control s button for 1-2  
seconds. The engine and parking lights will shut off.  
User-Programmable Temperature-Controlled Starting  
CAUTION : Do not activate Temperature-Controlled Starting while  
the vehicle is in an enclosed area.  
I
The AviStart system can be programmed to automatically start the vehicle  
engine whenever the temperature inside the vehicle reaches or drops below  
the preprogrammed temperature level. The AviStart will monitor the air  
temperature every 2.5 hours and will only start the engine during extreme  
cold temperatures. There are three temperature levels to choose from. (This  
feature is programmed OFF from the factory and must be programmed ON to  
operate.) (See the "Programming Table for System Features" on page 15).  
To Activate:  
Press the remote control d and s buttons at the same time. The parking  
lights will turn on for 3 seconds, shut off for 1 second, turn on for 3 seconds  
and shut off. This will be your visual indication that you have activated the  
Temperature-Controlled Starting feature.  
When the temperature inside the vehicle reaches the preprogrammed  
temperature level, the parking lights will flash 2 times, the vehicle will start  
and the parking lights will turn on. The vehicle will run for 10 minutes and  
then shut off. This will allow the engine to warm up and charge the battery.  
To Deactivate:  
Press the remote control d and s buttons at the same time for 1-2 seconds.  
The parking lights will turn on for 3 seconds and then turn off. This will be  
your visual indication that you have deactivated the Temperature-Controlled  
Starting feature.  
NOTE: At any time, if the ignition key is turned on or the vehicle is remote  
started, the Temperature-Controlled Starting feature will deactivate.  
12  
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pit Stop Mode  
CAUTION: Do not leave passengers or pets in the vehicle while the  
system is in Pit Stop Mode.  
I
The Pit Stop Mode allows you to park the vehicle for short-term stops, remove  
the ignition key and leave the engine running.  
To Activate:  
1. While the vehicle engine is running with the ignition key turned "ON,"  
press the remote control s button for 1-2 seconds. The parking lights will  
flash 2 times and then stay on and the doors will unlock. (Make sure the  
vehicle is in "Park" and set the emergency parking brake.)  
2. Turn the ignition key "OFF" and the engine will stay running.  
3. Remove the ignition key and remote control and exit the vehicle.  
Remember to keep the ignition key and remote control in your possession.  
4. Press the remote control A button for 1-2 seconds to secure your vehicle.  
To Deactivate:  
1. When you return to the vehicle, press the remote control A button for  
1-2 seconds. The doors will unlock.  
2. Enter the vehicle (do not touch the brake pedal), turn the ignition key to  
the "ON" position and then press the brake pedal. The parking lights will  
shut off and you will now be able to drive the vehicle.  
13  
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User-Programmable Features  
All AviStart system and remote control programmable features are  
accomplished by turning the ignition key "ON" (or starting the engine) and  
flicking the valet switch on and off a preset number of times.  
The AviStart also allows you to add new remote controls in one step, delete  
lost or stolen remote controls or rearrange the factory preset remote control  
functions.  
1 . Remove the system from Protected Valet Mode. Programming cannot be  
accessed while the system is in Protected Valet Mode indicated by the  
LED on solid red.  
2. Select the feature you wish to program from the "Programming Table for  
System Features" or the "Programming Table for Remote Controls" on  
pages 15 & 16. Note the number of chirps associated with that feature.  
3 . Turn the ignition key to the "ON" position.  
4. Within 10 seconds, begin flicking the valet switch on and off. The siren  
will chirp once each time you flick the switch on then off.  
5. Continue flicking the switch on and off, counting the number of chirps.  
NOTE: Stop when you reach the number of chirps associated with your  
chosen feature.  
6 . Follow the "Secondary Action." You will hear a number of chirps to  
confirm that you have changed the setting of that feature.  
7 . Turn the ignition key to the "OFF" position.  
8. Repeat steps 1-7 for any other feature you wish to program.  
14  
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming Table for System Features  
Factory No. of  
Feature  
Secondary Action  
Setting Chirps  
Wait 3 seconds, the siren will chirp once  
for active, twice for passive  
Active/Passive Arming  
Passive Door Lock  
Passive  
OFF  
4
5
6
7
Wait 3 seconds, the siren will chirp once  
for OFF, twice for ON  
Passive Arming Chirp/Light  
Flash Confirmation  
Wait 3 seconds, the siren will chirp once  
for OFF, twice for ON  
ON  
Wait 3 seconds, the siren will chirp once  
for OFF, twice for ON  
Remote Arming Siren Chirps  
ON  
Siren Duration  
30-60 Seconds  
Wait 3 seconds, the siren will chirp once  
for 60, twice for 30  
30  
ON  
OFF  
ON  
20  
8
Ignition-Controlled Door  
Lock/Unlock  
Wait 3 seconds, the siren will chirp once  
for OFF, twice for ON  
12  
14  
17  
19  
Wait 3 seconds, the siren will chirp once  
for OFF, twice for ON  
RPM Door Lock  
Wait 3 seconds, the siren will chirp once  
for OFF, twice for ON  
Door Ajar Indication  
Remote Start Run Time  
20 or 30 Minutes  
Wait 3 seconds, the siren will chirp once  
for 30 minutes, twice for 20 minutes  
Temperature-Controlled  
Starting  
Wait 3 seconds, the siren will chirp once  
for OFF, twice for 5°F (-15°C)  
OFF  
21  
OFF or 5°F (-15°C)  
Wait 3 seconds, the siren will chirp once  
for -7°F (-20°C), twice for -22°F (-30°C)  
-7°F (-20°C) or -22° F (-30°C)  
22  
23  
Wait 3 seconds, the siren will chirp once  
for OFF, twice for ON  
Security Start Locks™  
ON  
15  
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming Table for Remote Controls  
Factory  
Setting  
No. of  
Chirps  
Feature  
Secondary Action  
Press A Button, the siren will chirp  
Arm/Disarm  
A Button  
d Button  
s Button  
H Button  
24  
1 time.  
Remote-Controlled Trunk  
Release  
Press d Button, the siren will chirp  
25  
26  
27  
28  
2 times.  
Press s Button, the siren will chirp  
Remote Start  
3 times.  
Press H Button, the siren will chirp  
Silent Arm/Disarm  
4 times.  
A +s  
Buttons  
Press A + s Buttons, the siren will  
Remote-Controlled Valet  
chirp 5 times.  
Channel 6 Remote  
Controlled Accessory  
Output  
A +H  
Buttons  
Press A + H Buttons, the siren will  
29  
chirp 6 times.  
Remote-Controlled Sensor d +H  
Press d + H Buttons, the siren will  
30  
31  
Bypass  
Buttons  
chirp 7 times.  
Temperature-Controlled  
Start Active/Inactive  
d + s  
Buttons  
Press d + s Buttons, the siren will  
chirp 8 times.  
Channel 9  
Remote-Controlled  
Accessory Output  
H + s  
Press H + s Buttons, the siren will  
32  
33  
34  
Buttons  
chirp 9 times.  
One Step Remote Code  
Learning  
Press A Button, the siren will chirp  
A Button  
1 time.  
Wait 3 seconds, the siren will chirp  
twice, all codes are erased out of  
memory.  
Instant Remote Control  
Code Deletion  
16  
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Life time Lim ited Fac tory War ranty - Terms and Con di tions  
Avitalvehiclesecuritysystemsandaccessoriesrequireprofessionalinstallationby an Authorized  
Avital Dealer. Un less the sys tem is sold and in stalled by an Authorized Avital Dealer, all prod uct  
warranties are void. As the manufacturer, Avital Technologies war rants to the origi nal con su mer  
purchaser, the system control unit and re mote con trols to be free from de fects in ma te rial and  
workmanshipforaslongasyouownthevehicleinwhichthesystemwasoriginallyinstalled. All other  
parts of the sys tem and ac ces so ries to the sys tem are war ranted to be free from de fects in m aterialand  
work man ship for one (1) year from the date of pur chase. Avital Technologies will re pair or re p lace, at  
its op tion and free of charge dur ing the war ranty pe riod, any sys tem com po nent that proves d efective  
inmaterialorworkmanshipundernormalinstallation,use,andservice,providedtheproductisreturned  
to our fac tory by an Authorized Avital Dealer, trans por ta tion charges pre paid. Prod ucts re turned to our  
factorymustbeaccompaniedbyaphotocopyofthepurchasereceipt.Intheabsenceofsuch purchase  
re ceipt, the war ranty pe riod shall be one (1) year from the date of manu fac ture. Any dam age t o the  
prod uct(s) as a re sult of mis use, abuse, ne glect, ac ci dent, in cor rect wir ing, im proper in stallation,  
de struc tion or al tera tion of the se rial number, re pair or al tera tion out side our fac tory, or any use  
vio la tive of in struc tions fur nished by us will void the war ranty. This war ranty is lim ited todefective  
partsandspecificallyexcludesanyincidentalorconsequentialdamagesconnectedtherewith. This  
warranty is not transferable. Avital Technologies makes no war ranty against theft. This war ranty is not  
to be con strued as an in sur ance pol icy against loss. War ranty on in stal la tion la bor, re mo val and  
reinstallationchargesarenottheresponsibilityofAvitalTechnologies, Inc.  
TheftProtectionGuaranteeTermsandConditions  
In the event that your automobile is stolen and not recovered within 30 days, Avital Technologies, Inc.  
will refund to you, the original purchaser of the Avital system, your insurance theft deductible up to  
$3,000 (USA and Canada only) of the theft claim not covered by the theft deductible of your vehicle  
insurance. This guarantee applies only to the owner of the vehicle in which the Avital system was  
originally installed and only if you were the owner of this same vehicle when it was stolen. This  
guarantee is valid only in the USA and Canada and only if:  
(1) Installation of the Avital vehicle security product was performed by an Authorized Avital dealer.  
(2) Avital win dow stick ers are ad hered to both the driver’s- side and curb- side win dows and are  
clearly visi ble on both sides from out side the ve hi cle.  
(3) At the time of the theft, the Avital system was fully functional, armed and not in “valet mode.”  
(4) Your insurance company and the police have been notified and a written stolen vehicle report  
was issued by the Police Department.  
(5) No less than thirty (30) days after the police report was issued, you mail to Avital Technologies  
clear photocopies of the following documents:  
I. Thestolenvehiclepolicereportnotingthelocationandphonenumberofthepolicestati on  
thatissuedthereport.  
II. A dated declaration signed by you, the owner of the vehicle, attesting that the vehicle has  
been stolen for more than thirty (30) s and has not been recovered.  
III. A photocopy of the payment you received from your insurance company for the loss of your  
vehicle.  
IV. A photocopy of your insurance policy showing your name and the theft deductible.  
This guarantee is effective for one year from the date of purchase as indicated by your purchase re ceipt,  
is limited to one claim and is valid only when the entire vehicle was stolen and not recovered. Thi s  
guarantee is not transferable and specifically excludes any other consideration, including, but not  
limited to, damage caused to the vehicle, theft of parts or contents, or any consequential damages.  
Once Clifford Electronics verifies the above listed requirements have been met, a payment will be  
made to you in accordance with the above stated provisions.  
17  
AviStart 6501 Owner's Manual - 0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ONLINE REGISTRATION: For your convenience, we now provide online  
registration for your Avital purchase. Within 10 days of purchase, register at  
your Owner's Manual, as well as information on product updates or special  
promotions.  
Your sys tem se rial number is:  
Place se rial number sticker here  
© 1999 Avital Technologies, Inc., A Division of Clifford Electronics  
Part Number: 31-6501/AviStart6501OM/0999  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Agri Fab Spreader 45 03295 User Manual
Altec Lansing Food Processor 4948A User Manual
Altina Network Card GGM308U User Manual
Aluratek Computer Drive AHDU350 User Manual
Aluratek Portable Stereo System AWS01F User Manual
American Standard Indoor Furnishings T2117XX Series User Manual
AOC Flat Panel Television L24H898 User Manual
AOSafety Bluetooth Headset MT7H796 01 User Manual
Avital Remote Starter 3100L User Manual
Baracoda Barcode Reader BC2604 User Manual