Avital Automobile Alarm 3300L User Manual

Model 3300L

➤Owner’s Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WAR-

RANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY

PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH. THIS

EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY

AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WAR-

RANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL

WARRANTY OF NON-INFRINGEMENT OF PATENTS, IN THE UNITED

STATES OF AMERICA AND/OR ABROAD. NEITHER THE MANUFACTURER

OR ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR

LIABLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMIT-

ED TO ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, TOW-

ING, REPAIR, REPLACEMENT, DAMAGES FOR LOSS OF TIME, LOSS OF

EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY

AND THE LIKE. NOTWITHSTANDING THE ABOVE, MANUFACTURER

DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-

TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on

how long an implied warranty will last or the exclusion or limitation of incidental or con-

sequential damages. This warranty gives you specific legal rights, and you may also have

other rights which vary from state to state.

$2,500 Limited Theft Protection Guarantee

Terms and Conditions. Available only in the USA. In the event that your vehicle is stolen

and not recovered, Directed Electronics will refund to the original purchaser of the

Hornet system up to $2,500 of your insurance deductible. This vehicle protection guar-

antee is valid only if:

1. The installation was performed by an authorized Hornet dealer.

2. The warranty registration card is completed and mailed within ten (10) days of

purchase.

3. At the time of the theft, the system was fully functional and not in “valet mode.”

4. The vehicle and its contents were insured at the time of the theft.

5. The insurance company and the police have been notified and a written stolen vehicle

report was issued by the Police Department.

6. No less than thirty (30) days after the police report was issued, you mail Directed

Electronics clear photocopies of the following documents:

a. Proof of Purchase OR provide the system model and name of the company that

installed the system.

b. The stolen vehicle report issued by the police.

c. Insurance coverage documents for the stolen vehicle, clearly showing all the details,

including the vehicle identification number and the insurance deductible amount.

d. A dated declaration signed by you the owner of the vehicle, attesting that the

vehicle has been stolen for more than thirty (30) days and has not been recovered.

Download from Www.Somanuals.com. All Manuals Search And Download.

This vehicle theft protection is effective for one (1) year from the date of purchase and is

limited to one claim. This vehicle theft protection guarantee is valid only for the theft of

the entire vehicle and specifically excludes any other considerations, including, but not

limited to, damage caused to the vehicle, theft of parts, contents or any other consequen-

tial damages. Once Directed Electronics verifies that all the above listed terms and condi-

tions have been met, a check for the insurance deductible (up to $2,500) will be mailed

within thirty (30) days.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

➤ Date of purchase

➤ Your full name and address

➤ Authorized dealer's company name and address

➤ Type of alarm installed

➤ Year, make, model and color of the automobile

➤ Automobile license number

➤ Vehicle identification number

➤ All security options installed on automobile

➤ Installation receipts

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

table of contents

limited lifetime consumer warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

remote configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

LCD 2-way configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

standard 4-button configuration (both remotes) . . . . . . . . . . . . . . . . . . . . . . . . . 4

LCD 2-way remote additional controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

what is included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Standard LCD 2-way icon configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

LCD 2-way remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

system signal paging features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

using your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

active arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

warn away® response description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

triggered response description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

disarming without a remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

valet mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

nuisance prevention® circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

system status chirps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

code hopping . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

high frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

installation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Download from Www.Somanuals.com. All Manuals Search And Download.

remote configurations

LCD 2-way configuration

➜

Download from Www.Somanuals.com. All Manuals Search And Download.

Vehicle Interior Temperature Indicator

Numeric Display

AM/PM Indicator

Alarm Clock Mode Indicator

Timer Function Indicator

Transmit Range Indicator

Transmission Indication

Vibrate/Beep Mode Indicator

Power Saver Mode Indicator

Remote Start Timer Mode Indicator

No Function

Vehicle Page Mode Indicator

Full Trigger Shock Sensor Indicator

Hood/Trunk Open or Trigger Indicator

Parking Light Indicator

Door Open or Trigger Indicator

Arm/Lock Button

Disarm/Unlock Button

Remote Start Indicator

Hood/Trunk Open or Trigger Indicator

Remote Start Button

Valet Mode Indicator

Remote Start Safety Shutdown Indicator

Battery Level Indicator

Auxiliary Button

Temperature-Controlled Remote Start Indicator

Silent Arm/Disarm Mode Indicator

Full Trigger Alert Indicator

Arm/Disarm Indicator

Function Button

Celsius/Fahrenheit Indicator

Download from Www.Somanuals.com. All Manuals Search And Download.

standard 4-button configuration (both remotes)

➜

controls the Arm and Panic On/Off function. The

arming is controlled by pressing this button. The panic alarm is

triggered by pressing and holding this button. Press again to

cancel the panic alarm

Disarm

Panic

Off function. Press this

controls the

and

button to disarm the system or to cancel the panic alarm.

Silent Mode™

Auxiliary

controls

and

channel output.

Silent mode works by pressing this button for less than one

second before arming or disarming. And optional auxiliary func-

tion, such as trunk release, can be controlled by pressing and

holding this button for 1.5 seconds.

The auxiliary output controls __________________________.

Panic

controls the

function by pressing and holding this

button for 1.5 seconds.

and

pressed together control channel output,

and optional auxiliary convenience or expansion function that

you have added to your system.

The auxiliary output controls __________________________.

Download from Www.Somanuals.com. All Manuals Search And Download.

and

pressed together control channel output,

and optional auxiliary convenience or expansion function that

you have added to your system..

The auxiliary output controls __________________________.

LCD 2-way remote additional controls

➜

note: The controls listed below are applicable only to the

LCD 2-way remote.

The LCD backlighting will turn on when pressed for less

than one second; when held for more than five seconds the trans-

ceiver will enter adjustment mode allowing the setting of the

clock, timer mode, and audible melody selection. For more infor-

mation, please refer to the Function Button Configurations section

of this guide.

and

Buttons

The numeric display toggles between the time of the day and the

alarm clock when these buttons are pressed simultaneously.

and

Buttons

Press these buttons simultaneously to activate the parking timer.

Each additional press will toggle through the available options

(10 min., 20 min., 30 min., 1 hour, 1.5 hours, 2 hours, and off).

Download from Www.Somanuals.com. All Manuals Search And Download.

and

Buttons

When pressed simultaneously these buttons toggle between beep

notification and vibrate notification.

and

Buttons

When pressed simultaneously these buttons activate battery saver

mode, which will drop power consumption on the transceiver

battery to zero when the alarm is inactive or disarmed.

what is included

➤ Control module

➤ 544N transceiver/antenna

➤ One 4-button remote

➤ One 2-way LCD remote

➤ Impact sensor on-board control module

➤ High powered siren

➤ Fault-proof starter interrupt relay on-board control module

➤ Status LED indicator light

➤ Push-button Valet button

➤ Your warranty registration

Download from Www.Somanuals.com. All Manuals Search And Download.

important information

Congratulations on the purchase of your state-of-the-art vehicle

security system. This system has been designed to provide years

of trouble-free operation. By carefully reading this guide prior to

using your system, you will maximize the use of this product and

its features.

By carefully reading this Owner's Guide prior to using your

system, you will maximize the use of this system and its features.

You can print additional or replacement copies of this manual by

accessing our web site at www.directed.com.

system maintenance

➜

The system requires no specific maintenance other than battery

replacement for the remotes.

LCD 2-Way Remote Battery Replacement

The 2-way remote is powered by a 1.5V AAA battery. The

Battery Level indicator has three level indicators that serve as a

visual indication of battery charge. When the battery reaches a

low charge level that requires replacement, the transceiver will

generate a single notification chirp, and the Battery Level indi-

cator will flash continuously.

Download from Www.Somanuals.com. All Manuals Search And Download.

To replace the battery, gently pull the battery cover release tab, then

slide the door down to expose the battery and remove the expired

battery. Place the new battery into the transceiver observing the

correct polarity. When power is returned the transceiver will light

all icons in the LCD and generate a musical tone.

4-Button Remote Battery Replacement

Your remote is powered by a small, lightweight 3-volt lithium

battery (CR2032) that will last approximately one year under

normal use. When the battery begins to weaken, operating range

will be reduced and the LED on the remote will dim.

your warranty

➜

Your warranty registration must be completely filled out and

returned within 10 days of purchase. Your product warranty

will not be validated if your warranty registration is not returned.

Make sure you receive the warranty registration from your dealer.

It is also necessary to keep your proof of purchase, which reflects

that the product was installed by an authorized dealer.

fcc/id notice

➜

This device complies with Part 15 of FCC rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesirable operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Directed Electronics, Inc.

544 Series

Tested to Comply

with FCC Standards

Directed Electronics, Inc.

477T Series

Tested to Comply

with FCC Standards

Directed Electronics, Inc.

474V/P/S Series

Tested to Comply

with FCC Standards

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this device.

Download from Www.Somanuals.com. All Manuals Search And Download.

Standard LCD 2-way icon configuration

Icon

➜

The vehicle interior temperature icon has no functions

Icon

The numeric display icon will show the hours and minutes.

Icon

The AM/PM icon indicates the time before or after noon.

Icon

The alarm clock mode icon indicates that the alarm clock mode

is active.

Icon

The timer function icon flashes during timed functions including

parking timer.

Icon

The transmit range indicator icon stays visible as long as the

system is within operating range.

Icon

The remote transmission indicator icon displays when the trans-

ceiver is transmitting a signal.

Icon

The vibrate/beep mode icon appears when the transceiver is set

to vibrate mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Icon

The power saver mode can be turned on or off with the trans-

ceiver. This icon displays the status.

Icon

The remote start timer mode icon has no function.

Icon

No function.

Icon

The vehicle page mode icon displays when the alarm module is

paging the transceiver.

Icon

The full trigger shock sensor icon indicates that the shock sensor

has been triggered by a hard shock.

and

Icons

The hood/trunk open or trigger icon illuminates when the hood

or trunk trigger has been activated or the hood or trunk is open,

and bypasses those zones until it is closed.

Icon

The parking light icon will flash twice when armed or disarmed.

The icon also flashes during WarnAway.

Icon

The door open or trigger icon illuminates when the door trigger

has been activated or the door is open, and bypasses that zone

until it is closed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Icon

The remote start icon has no function.

Icon

The Valet mode icon appears when the system is in Valet mode.

Icon

The remote start safety shut down icon has no function.

Icon

The battery level icon indicates the level of power remaining in

the battery.

Icon

The temperature-controlled remote start icon has no function.

Icon

The silent arm/disarm icon appears when the system has been

armed or disarmed in the silent mode.

Icon

The full trigger alert icon illuminates when the security system

has been triggered by a heavy impact, door trigger violation,

optional sensor violation, or a hood/trunk trigger.

Icon

The arm icon appears when the vehicle is armed and locked. The

disarm icon appears when the vehicle is disarmed and unlocked.

Icon

Celsius/Fahrenheit icon indicates the current mode of the

displayed temperature either in Celsius or Fahrenheit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Standard LCD 2-way button functions

Audible

Indication

Function

Button

Icon

Lamp On

(10 sec)

Power-Saver Mode*

Beep/Vibrate Mode

Melody

4 Vibrations/

1 Beep

Time Adjust

for 5 Seconds

1 Time***

2 Times***

3 Times***

4 Times***

2 Beeps

Mode (hour)**

Time Adjust

Mode (min)**

Alarm Clock

Set Mode (hour)**

Alarm Clock

Set Mode (min)**

Alarm Clock Music

or Power on Music

Selection**

5 Selections

1/2/3/4/5

Alarm Clock Adjust

Mode (on/off)**

5 Times***

6 Times***

Timer Count Down

Adjust Mode

(hour)**

Timer Count Down

Adjust Mode

(min)**

7 Times***

8 Times***

9 Times***

Timer Count

5 Selections

1/2/3/4/5

Down Ending Melody

Selection 1**

RS Timer Count

Down Mode (on/off)* (where applicable)

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Start On

10 times***

5 Selections

1/2/3/4/5

Melody Selection 2 (where applicable)

10 Min Parking

1 Time

2 Times

3 Times

4 Times

5 Times

6 Times

7 Times

Melody

Count Down Mode

20 Min Parking

Count Down Mode

30 Min Parking

Count Down Mode

60 Min Parking

Count Down Mode

90 Min Parking

Count Down Mode

120 Min Parking

Count Down Mode

Parking Count Down

Off Mode

Alarm Clock Mode

On/Off****

Celsius/Fahrenheit

Select Mode

* This function will operate in the disarmed state only.

** The button will advance the selection upward. The

button will advance the selection downward or select the off set-

ting.

*** Be sure to hold

down for five seconds prior to entering

timer clock adjust mode operation.

**** Press once to have the alarm clock on. Press twice to have the

alarm clock off.

The remote will revert to normal operation from the set mode

when 15-seconds has elapsed without a button entry.

Download from Www.Somanuals.com. All Manuals Search And Download.

LCD 2-way remote operation

The remote start system operates at 434 MHz and incorporates

Directed’s proprietary A.S.K. out-board two-way transceiver. The

high frequency combined with Binary Data communication

achieves superior range with two-way communication.

system signal paging features

➜

A page is the signal the control module sends to the transceiver as

confirmation of receipt of a command or alarm system status.

When the transceiver receives a page it will generate a page notifi-

cation to the user (notifications are audible beeps or the remote

vibrates) and the LCD icons will display the current system status.

Command Page

When a command (arm/disarm, or auxiliary channel) from the

transceiver is sent and received, the system will send a command

page back to confirm receipt.

Page Recognition Mode

The transceiver will leave a zone icon illuminated when it has

received a triggered response and will wait for violation recogni-

tion. Press any button on the transceiver, the LCD information

and alarm page alerts will be cleared.

note: The transceiver buttons will not send a command

to the system until the alarm page is cleared.

Download from Www.Somanuals.com. All Manuals Search And Download.

using your system

important: Due to the complexity of this system, instal-

lation of this product must only be performed by an

authorized Directed dealer.

active arming

➜

You can arm the system by pressing

of your remote for one

second. When the system arms, you will hear a short siren sound,

or chirp, and see the parking lights flash once. If the power door

locks are controlled by the system, the doors will also lock. While

the system is armed, the status LED will flash approximately once

per second, indicating that the system is actively protecting your

vehicle. If you hear a second chirp after arming and note that the

status LED is flashing in groups, see the Diagnostics Section of

this guide. This extra chirp is called Bypass Notification, which

indicates that a security sensor or switch has been bypassed and

the system is not monitoring that area (zone) of the vehicle.

passive arming

➜

The system can be programmed to arm itself automatically (called

passive arming). If the system is programmed for passive arming, it

will automatically arm 30 seconds after the ignition is turned off

and the last protected entry has been closed. (e.g. the system detects

that you have left the vehicle by opening and closing a door.)

Whenever the system is in its 30-second passive arming countdown,

the status LED will flash twice as fast as it does when the system is

armed. If the system is programmed for Passive Arming, care must

be taken to prevent the keys from being locked in the vehicle.

Download from Www.Somanuals.com. All Manuals Search And Download.

note: If any protected entry point (such as a door or a

switch-protected trunk or hood) is open, the system will

not passively arm. Additionally, each time a protected

entry is opened (triggered) during the arming count-

down, the 30-second countdown starts over.

When armed your vehicle is protected as follows:

➤ Light impacts trigger the Warn Away signal. When triggered,

the siren chirps and the parking lights flash for a few seconds.

➤ Heavy impacts trip a Triggered Sequence. The sequence

consists of the siren sounding continuously and the parking

lights flashing for 30 seconds.

➤ If a door is opened, the system will immediately start

chirping the siren and flashing the parking lights. Three

seconds later, the siren output changes to a continuous blast.

This progressive response gives you time to disarm the system

with your remote if you inadvertently open the door while

the system is armed.

➤ Turning on the ignition key will trip the same progressive re-

sponse as opening a door.

➤ The starter kill prevents the vehicle’s starter from cranking.

warn away^®response description

A Warn Away Response consists of an alarm page along with the

➜

responses described below.

Shock Sensor

➤

- Light impacts to the vehicle will flash the

vehicle lights and chirp the siren for a few seconds.

Remote Control Notification

tions).

➤

- Ten quick beeps (or vibra-

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Control LCD

➤

- The full trigger alert icon (28) will

dimly illuminate for two seconds

➤ The transceiver will enter Page Recognition Mode and

operate alarm page alerts.

note: Icons 13 and 14 represent alarm system zone

inputs. For more information about icons and the zones

they represent refer to the Standard Remote Configurations

section.

triggered response description

➜

A Triggered Response can be activated by any of the triggers listed

below and consists of an alarm page along with the response

described for each trigger. The Triggered Response duration is 30

seconds.

Sensor Trigger

➤

- Heavy impacts to the vehicle will instantly

sound the siren and flash the lights for the programmed

duration and report Zone 2.

Door Trigger

➤

- If a door is opened the siren will chirp for three

seconds, then the siren will sound and the lights will flash for

the programmed duration and report Zone 3. The three

seconds allow the user time to disarm the system with a

minimum of noise should a door be opened inadvertently

while the system is armed.

Hood Trigger

➤

- Opening the hood (if connected) will sound

the siren, flash the lights for the programmed duration, and

report Zone 1.

Trunk Trigger

- Opening the trunk (if connected) will

instantly sound the siren and flash the lights for the

programmed duration and report Zone 1.

Download from Www.Somanuals.com. All Manuals Search And Download.

Ignition Trigger

➤

- If the ignition is turned on the siren will

chirp for three seconds, then the siren will sound and the lights

will flash for the programmed duration and the remote will

flash.

When a Triggered Response is activated the transceiver will:

➤ Repeat four quick beeps (or vibrate) for 15 seconds.

➤ The full trigger alert icon (28) will turn on for 15 seconds.

➤ The zone icons will turn on and remain on until a transceiver

button is pressed, clearing the page alert.

➤ The transceiver will enter page recognition mode and

generate alarm page alerts.

note: Icons 13, 14, 16, and 20 represent alarm system

triggered sequence zone inputs. For more information

about icons and the zones they represent refer to the

Standard Remote Configurations section.

disarming

➜

To disarm the security system, press

. You will hear two

chirps, and the parking lights will flash twice. If the power locks

are controlled by the system, the doors will also unlock. If the

siren chirps more than twice and the LED continues to flash after

pressing the

button, the system was triggered in your

absence (Tamper Alert). Refer to the disarming discussion in the

Diagnostics Section of this guide.

Download from Www.Somanuals.com. All Manuals Search And Download.

high security disarm

➜

This security system offers High Security Disarm. High Security

Disarm is a feature that makes it possible to silence and reset the

system while it is triggering, without disarming the system. If the

system is triggered and the siren has been sounding for longer

than six seconds, pressing

on the remote will stop the trigger

and return the unit to the armed state. The system will not

disarm, but rather reset. This prevents you from disabling the

system should you wish to disarm it without visually checking the

vehicle. Pressing

after resetting the system will disarm the

system; pressing this button during the first six seconds of the

triggered sequence will disarm the security system immediately.

The six second timer is provided for your convenience, in case the

system is accidentally triggered.

disarming without a remote

➜

If your remote is lost or damaged, you can manually disarm your

vehicle security system. To disarm the system without a remote,

you must have the vehicle's ignition key and know where the

Valet button is located. Be sure to check with your installer at the

time of installation for the location of the Valet button.

Download from Www.Somanuals.com. All Manuals Search And Download.

To disarm the security system,

turn the ignition to the ON posi-

tion. Press the Valet button

within 15 seconds. After five

seconds, the system will disarm. If

the system does not disarm, you

may have waited too long; turn

the ignition off and on and try

again.

DRW-35

Location of Valet Button_________________________________

silent mode

➜

To temporarily turn off the arm or disarm chirps, use Silent

Mode™. Simply press

for less than one second before

arming or disarming, and the confirmation chirp(s) will be elim-

inated for that one operation only. If you want the arm/disarm

chirps turned off permanently, your dealer can do this for you.

note: The Warn Away response to lighter impacts is

bypassed if the system is armed using Silent Mode. This

ensures that no chirps will be emitted by the siren in an

area you want chirp-free. The system is still fully capable

of triggering by heavy impacts. Only the Warn Away

response is bypassed.

Download from Www.Somanuals.com. All Manuals Search And Download.

panic mode

➜

If you are threatened in or near your vehicle, you can attract

attention by triggering the system with your remote. Just press

for 1.5 seconds, and you will enter Panic Mode. The siren

will sound and the parking lights will flash for the programmed

siren duration.

To stop Panic Mode at any time, press

The LCD 2-way remote will beep (or vibrate) continuously when

the system enters panic mode. The 2-way remote will not

generate a page notification when panic mode is exited.

valet mode

➜

You can prevent your security system from automatically arming

and triggering by using Valet Mode. This is very useful when

washing the vehicle or having it serviced. In Valet Mode, the

security system will not arm, even with the remote, but all conve-

nience functions (door locks, trunk release, etc.) will continue to

work normally. You can access Valet Mode either manually or

with the remote.

To enter or exit Valet Mode manually:

1. Turn the ignition on.

2. Turn the ignition off.

DRW-35

3. Press and release the Valet

button within 10 seconds.

The status LED will light solidly if you are entering Valet Mode,

and it will go out if you are exiting Valet Mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

To enter or exit Valet Mode using the remote:

Steps 2 through 3 must be quickly and smoothly completed.

1. Open any vehicle door.

2. Press

3. Press

4. Press

again.

The status LED will light solidly if you are entering Valet Mode,

and it will go out if you are exiting Valet Mode.

setting the clock

➜

To set the clock press and hold

ceiver will chirp twice and the hour selection will start flashing.

Immediately press to advance the hour selection or to

reverse the hour selection. Once the correct hour is displayed

for five seconds, the trans-

press

again and the minute selection will start flashing. Then

to advance the minute selection or to reverse the

minute selection. Once the correct time is displayed simply stop

pressing any buttons for 15 seconds and the transceiver will auto-

matically exit the clock mode.

nuisance prevention^®circuitry

Your system has Directed’s Nuisance Prevention Circuitry

➜

(NPC ). It prevents annoying repetitive trigger sequences due to

faulty door pin switches or environmental conditions such as

thunder, jackhammers, airport noise, etc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Example

If the alarm triggers three times within a 60-minute period and

each time the same sensor or switch triggers the alarm, NPC will

interpret those triggers as false alarms. After the third trigger,

NPC ignores, or bypasses, that sensor or switch (along with any

other sensors or switches sharing the same zone) for 60 minutes.

If the bypassed sensor tries to trigger the security system while it

is being bypassed, the 60-minute bypass period will start over.

This ensures that a sensor that is continually being triggered will

remain bypassed.

The vehicle doors are protected by NPC differently. If your

security system is triggered by an open door for three, full 30-

second cycles (one and one half minutes), the system will bypass

the doors until the trigger ceases.

note: Arming and disarming the system does not reset

this function! The only ways to reset a bypassed zone are

for it to not trigger for 60 minutes, or to turn on the igni-

tion. If testing your system, it is important to remember

that the NPC programming can cause zones to be

bypassed and appear to stop working. If five chirps are

heard when disarming, NPC has been engaged. If you

wish to clear the NPC memory, turn the ignition on.

Download from Www.Somanuals.com. All Manuals Search And Download.

diagnostics

The microprocessor at the heart of your system is constantly

monitoring all of the switches and sensors connected to it. It is

designed to detect any faulty switches and sensors and prevents

them from disabling the entire system. The microprocessor will

also record and report any triggers that occurred during your

absence. Refer to the System Status Chirps and Table of Zones

sections of this guide for diagnostic information.

arming diagnostics

➜

If the security system is armed at the same time that an input is

active (such as a door opening or sensor triggering), you will hear

one siren chirp to indicate arming and a second siren chirp to indi-

cate Bypass Notification. A Bypass Notification chirp means that

the security system ignores the input that was active when the

system was armed, until that input ceases. Three seconds after that

input ceases, the security system will resume normal monitoring.

For example, if your vehicle has an interior light exit delay and you

arm your security system before the interior light turns off, you

may hear a second Bypass Notification chirp. Three seconds after

the light turns off, however, the security system resumes normal

monitoring.

note: Bypass Notification does not occur when the sys-

tem is in Silent Mode or if the notification chirps have

been programmed off by the installer.

Download from Www.Somanuals.com. All Manuals Search And Download.

disarming diagnostics

➜

Extra chirps that are heard when disarming the system are the

Tamper Alert. If four chirps are heard when disarming the

system, then the security system was triggered in your absence. If

five chirps are heard when disarming the system, a zone was trig-

gered so many times that the Nuisance Protection Circuitry has

bypassed that zone. In either case, the status LED will indicate

which zone was involved (see Table of Zones section). The secu-

rity system will retain this information in its memory and chirp

four or five times each time it is disarmed, until the next time

that the ignition is turned on.

system status chirps

➜

The siren will chirp when arming/disarming the system. The

pattern of chirps will audibly report the system’s status as

described below.

Action

Arm

Number of Chirps

Description

System armed

Arm

1 (3-second delay), 1

System armed with

Bypass Notification

Disarm

System disarmed

System disarmed with

Tamper Alert

Disarm

System disarmed NPC

active

Download from Www.Somanuals.com. All Manuals Search And Download.

table of zones

➜

A zone is represented by the number of LED flashes used by the

system to identify a particular type of input. Standard input

assignments are listed in the following table, along with spaces to

write in any optional sensors or switches that have been installed.

ZONE

(Number of

LED Flashes)

DEALER-INSTALLED

OPTIONS

DESCRIPTION

Instant trigger for optional

hood or trunk pin

Instant trigger - a heavier impact

detected by the on-board shock sensor

Door switch trigger

Ignition trigger

code hopping

The receiver and remotes use a mathematical formula called an

algorithm to change their code each time the remote is used.

This technology has been developed to increase the security of

the unit. The control unit knows what the next codes should be.

This helps to keep the remote “in sync” with the control unit

even if you use the remote control out of range of the vehicle.

However, if the remote has been pressed many times out of range

of the vehicle, or the battery has been removed, it may fall out of

sync with the control unit and fail to operate the system. To re-

sync the remote simply press

several times within range of

Download from Www.Somanuals.com. All Manuals Search And Download.

the vehicle. The alarm will automatically re-sync and respond to

the remote normally.

high frequency

Your system transmits and receives at 434 MHz. This provides a

cleaner spectrum with less interference and a more stable signal.

Enjoy a phenomenal increase in range, even in areas with high

radio interference.

rapid resume logic

This Directed system will store its current state to non-volatile

memory. If power is lost and then reconnected the system will

recall the stored state from memory. This means if the unit is in

Valet Mode and the battery is disconnected for any reason, such

as servicing the car, when the battery is reconnected the unit will

still be in Valet Mode. This applies to all states of the system

including arm, disarm, and Valet Mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

programming options

Programming options control your system's normal, operational

set-up. Most options do not require additional parts, but some

may require installation labor.

The following is a list of the programmable options, with the

factory settings in Bold.

Active

➤

arming (from remote only) or passive arming (auto-

matic arming 30 seconds after the last door has been closed).

➤ Arming/disarming siren chirps

or off.

➤ The ignition controlled door lock feature or off: When this

feature is programmed on, the doors will lock three seconds

after the ignition is turned on, and unlock when the ignition

is turned off.

active door

➤ Passive door locking (with passive arming) or

locking

(only when arming with the remote). Passive locking

allows the vehicle's doors to lock when the security system

passively arms (after the 30-second countdown). This

feature only works if passive arming has been programmed.

™

➤ Siren tones and chirp volume. The output of the Revenger

™

Soft Chirp siren consists of six different tones in sequence.

Any of these tones can be eliminated by a dealer, resulting in a

unique, easily identifiable siren sound. The chirps can be either

6 decibels quieter

full volume or

than the full alarm blast.

Download from Www.Somanuals.com. All Manuals Search And Download.

security & convenience expansions

Listed below are some of the many expansion options available.

Please consult your dealer for a complete explanation of all the

options available to you.

Audio Sensor: Metal on glass, glass cracking, and breaking

glass produce distinctive acoustic signatures. The 506T audio

sensor uses a microphone to pick up sounds, then analyzes them

with proprietary acoustic software to determine if the glass has

been struck.

Backup Battery: The 520T keeps the system armed, triggers the

alarm and keeps the starter interrupt active if main battery is dis-

connected.

Field Disturbance Sensor: An invisible dome of coverage is estab-

lished by installing the 508D “radar” sensor. Your system can

react to any intrusions into this field with the full triggered

sequence.

Power Locks: This system offers lock outputs that can control

some manufacturers' power door lock systems. For other

systems, additional parts may be required.

Power Trunk Release: The accessory output of the system can op-

erate a factory power release for the vehicle’s trunk or hatch.

Although the on-board relay can control most power trunk re-

leases, sometimes an optional relay is required. If the factory

release is not power-activated, Directed 's 522T trunk release

solenoid can often be added.

Download from Www.Somanuals.com. All Manuals Search And Download.

Power Window Control: Automatic power window control is pro-

vided with the 529T and 530T systems. These can operate

power windows, and can roll them up automatically when the

system is armed, roll them down, or both up and down.

installation options

Installation options may require additional parts or labor. Please

consult your dealer.

Progressive Unlocking:

With electric power door locks, the

system can be configured so that when disarmed, only the

driver’s door unlocks. A second press of the disarm button within

15 seconds of disarming unlocks the remaining doors.

Horn Honk:

If connected, the horn will sound if the alarm is

either triggered by an intrusion or activated by Panic Mode. (In

most vehicles, this feature requires that an additional relay be

installed.)

Interior Light Illumination:

The interior domelight can be

configured to illuminate for 30 seconds after the alarm is

disarmed. If the system is rearmed during that 30-second period,

the interior light illumination will terminate until the alarm is

disarmed once again.

Download from Www.Somanuals.com. All Manuals Search And Download.

glossary of terms

Control Unit: The “brain” of your system. Usually hidden under-

neath the dash area of the vehicle. The control unit houses the

microprocessor which monitors your vehicle and controls all

system functions.

Fault-Proof Starter Interrupt: An automatic switch controlled by

your system that prevents the vehicle’s starter from cranking

whenever the system is armed. The vehicle is never prevented

from cranking when the system is disarmed, in Valet mode, or if

the starter interrupt switch itself fails. Your system has feature-

ready circuitry for the starter interrupt, however installation may

require additional labor.

Input: A physical connection to the system. An input can be

provided by a sensor, pinswitch or by existing systems in the

vehicle, such as ignition or courtesy lights.

LCD 2-Way Remote: A hand-held, transceiver which operates and

monitors the various functions of your system.

LED: A red light mounted at a discretionary location inside the

vehicle. It is used to indicate the status of your system.

Shock Sensor: This system has a dual zone shock sensor. This

sensor is mounted in the vehicle and designed to pick up impacts

to the vehicle or glass.

Download from Www.Somanuals.com. All Manuals Search And Download.

Trigger or Triggered Sequence: This is what happens when the

alarm “goes off” or “trips.” The triggered sequence of your

system consists of the siren sounding and parking lights flashing

for the programmed duration.

Valet Button: A small push-button switch mounted at a discre-

tionary location inside the vehicle. It is used to override the

starter interrupt when a remote is lost or damaged, or to enter or

exit Valet Mode.

Warning Zone Response: Lighter impacts to the vehicle will

generate the Warning Zone response. It consists of several

seconds of siren chirps and parking light flashes.

Zone: A zone is a separate input that the alarm can recognize as

unique. Each input to the system is connected to a particular

zone. Often two or more inputs may share the same zone.

Download from Www.Somanuals.com. All Manuals Search And Download.

QUICK REFERENCE GUIDE

Arming

To arm, press

■

. When the system arms, you will hear a short chirp, and

the parking lights will flash once.

Disarming

To disarm, press

flash twice.

■

. You will hear two chirps, and the parking lights will

High security disarm

For high security disarm, press

■

on your remote and the siren will stop

sounding. To completely disarm the security system, press again and the

system will chirp 4 or 5 times (reporting the trigger).

Disarming without a remote

■

Turn on the ignition. Press the Valet button within 15 seconds. The system

should now disarm. If it does not, you may have waited too long, so turn the

ignition off and on and try again.

Silent Mode^™

Pressing

tion chirp(s) for that one operation only.

■

briefly before arming or disarming will eliminate the confirma-

Panic Mode

Press

and the parking lights will flash for 30 seconds. To stop Panic Mode at any

time, press on the remote again.

■

for 2 seconds, and you will enter Panic Mode. The siren will sound

Location of Valet switch_________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

The company behind this system is Directed Electronics.

Since its inception, Directed Electronics has had one purpose, to provide consumers with

the finest vehicle security and car stereo products and accessories available. The recipient of

nearly 100 patents and Innovations Awards in the field of advanced electronic

technology, Directed is ISO 9001 registered.

Quality Directed Electronics products are sold and serviced throughout North America

and around the world.

Directed Electronics is committed to delivering world class quality products

and services that excite and delight our customers.

Vista, CA 92081

www.directed.com

G3300L 2008-12

Download from Www.Somanuals.com. All Manuals Search And Download.

ADTRAN Network Router 1200263L1 12A User Manual
AEG Refrigerator C 8 16 41 I User Manual
Alienware Laptop m5550 User Manual
Aluratek Computer Drive AHDU350 User Manual
American DJ DJ Equipment Light Station User Manual
Audiovox Car Stereo System ACD17 User Manual
Audiovox Car Stereo System AV303 User Manual
Ayre Acoustics Stereo System C 5xe User Manual
Bakers Pride Oven Oven VG16 User Manual
Baldor Motor Scooter MN710 User Manual