Model
AX-2K4 AX-2K4S,
AX-2K4MS, & AX-2K4MSFL
Transmitter Programming Guide
These transmitters makes use of icons (symbols) to identify the reac-
tion your security system/keyless entry/and or remote start system,
where applicable, will have when any icon (button) is pressed.
These icons are programmed at time of installation to meet the needs of
the individual and to complement the vehicle that the system is installed
in. To replace a transmitter or add transmitters, please follow the
programming instructions listed on the pages of this manual.
RECEIVER
CHANNEL
SYSTEM FUNCTION
BUTTON
Lock And Arm Alarm, also initiate and
terminates *Panic
1
Unlock And Disarm, also initiates and
terminates *Panic. Programmable to
unlock drivers door and or all doors.
2
1
Lock and arm/unlock and disarm. May
be programmed to unlock driver's door
or all doors. Also will initiate and
terminate *Panic.
Pulsed or switched output to control
Remote Trunk Release or optional
device connected to channel 3.
3
3
When pressed and release two times,
will provide pulsed output or activate the
Remote Start option when installed.
When so equipped, this button can be
used to operate an optional device
connected to channel 4.
4
5
When so equipped, this button can be
used to operate an optional device
connected to channel 5.
* Where So Equipped
128-6987
1 of 6
Download from Www.Somanuals.com. All Manuals Search And Download.
channel 2. The siren will chirp 2 times and the dash mounted LED will
Flash 2 times, indicating that the unit is ready to accept programming
for channel # 2 which is only used for separate lock and unlock
button transmitters, and is the disarm/unlock/unlock 2 and panic.
6) Press and hold the unlock symbol button of the transmitter you wish
to program for 4 seconds or until a long chirp is heard from the
siren.
"Repeat step 6 for each transmitter you wish to program".
7) Press and release the valet push button switch one time to ad-
vance to channel 3. The siren will chirp 3 times and the dash
mounted LED will Flash 3 times, indicating that the unit is ready
to accept programming for channel # 3 which is the trunk re-
lease/alternate output channel of the system.
8) Press and hold the trunk/key symbol button of the transmitter you
wish to program for 4 seconds or until a long chirp is heard from the
siren.
"Repeat step 8 for each transmitter you wish to program".
9) Press and release the valet push button switch one time to advance
to channel 4 if so equipped. The siren will chirp 4 times and the
dash mounted LED will Flash 4 times, indicating that the unit is ready
to accept programming for channel # 4, optional device (where
equipped)
10) Press and hold the Option button of the transmitter you wish to
program for 4 seconds or until a long chirp is heard from the siren.
"Repeat step 10 for each transmitter you wish to program".
11) Press and release the valet push button switch one time to ad-
vance to channel 5 if so equipped. The siren will chirp 5 times and
the dash mounted LED will Flash 5 times, indicating that the unit is
ready to accept programming for channel # 5 optional device (where
equipped)
12) Press and hold the second Option button of the transmitter you
wish to program for 4 seconds or until a long chirp is heard from the
siren.
"Repeat step 12 for each transmitter you wish to program".
ERASING TRANSMITTERS IF THEYHAVE BEEN LOST OR STOLEN:
NOTE: Before you begin to erase the lost or stolen transmitter(s),
have all transmitters available that you wish to remain pro-
grammed. These will be used during the program process
to identify transmitters that will continue to be used.
Enter the transmitter program mode:
1. Turn the ignition switch to the “ON” position.
2. Within 10 seconds, press and release the valet/program switch
three times. (Siren emits 1 short chirp indicating channel 1 has
been entered)
3. Within 10 Seconds, press and hold the ARM or ARM/DISARM
3
128-6987
3 of 6
Download from Www.Somanuals.com. All Manuals Search And Download.
button of the first transmitter you wish to remain stored into the
control unit until a single chirp is heard from the siren.
(Repeat this for each transmitter you wish to remain stored in the control
unit).
The receiver stores up to four transmitters. To be certain all transmitter
slots in the receiver are occupied with transmitters you wish to con-
tinue to use, and all others are erased, you will have to fill all four
receiver slots. If in step 3 you identified one transmitter, you will have
to fill the additional 3 slots. If in step 3 you identified two transmitters,
you will have to fill the additional two slots, etc...
4. Press and hold any unused button or combination of buttons until a
long chirp is heard from the siren. Release and press the button or
button combination again and again until all remaining slots are full.
NOTE: The button or combination of buttons entered will also control
the arm or arm/disarm function until additional transmitters are
added. All unwanted transmitters are now deleted.
REPRIORITIZING A TRANSMITTER’S PROGRAMMING:
To reprogram a receiver channel with a different transmitter button
once a code has been stored, there will be two options:
1. Enter the transmitter program mode of the receiver channel to be
reprogrammed. Using any unused button or combination of but-
tons, push out the stored code by pressing the unused button until
a long chirp is heard, then repeat 3 additional times. After this, you
can add any desired unused transmitter button. This action erases
only the button stored of the transmitter you are programming. All
other codes will remain stored.
2. Enter the transmitter program mode. Using any transmitter button
press and hold until a long chirp is heard. If a single chirp or multiple
chirps, (up to 7 chirps), are heard, the unit is indicating that the
transmitter has already been programmed elsewhere in the re-
ceiver. Release the transmitter button and within 5 seconds press
and hold until a long chirp is heard. This action forces the unit to
erase all stored codes of that transmitter.
The unit then exits the program mode the siren emits the program mode
exit chirp pattern. All transmitter buttons for that transmitter must now
be reprogrammed. Any other transmitter stored in the unit’s memory
still remain operational. If the button is released and not pressed again
within the 5 second period, no change in programming has been made
to the receiver channel. The programmer can move onto a different
channel or erase the transmitter codes as described in 1 above.
OPERATING THE FLASHLIGHT OFAX-2K4FL
If the transmitter packaged with your system included the
AX-2K4FL, (Flashlight Transmitter) By pressing the button located on
the side of the transmitter will cause the light on the end of the unit to
turn on.
4
128-6987
4 of 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The light will turn off when the button is released.
Caution! Always point the light away from you and the eyes of
others. This is a bright high intensity LED which should not be directed
toward or into the eyes of anyone.
QUICK REFERENCE CHART:
You can program any individual channel without reprogramming all
channels. To go directly to a particular receiver channel follow the
chart below:
CHANNEL
VALET SWITCH
LED
1 Ign. On Then
2 Ign. On Then
3 Ign. On Then
4 Ign. On Then
5 Ign. On Then
6 Ign. On Then
Press and Release 3 Times
1 Flash
Press and Release 4 Times 2 Flashes
Press and Release 5 Times 3 Flashes
Press and Release 6 Times 4 Flashes
Press and Release 7 Times 5 Flashes
Press and Release 8 Times 6 Flashes
BATTERY REPLACEMENT:
The transmitter incorporates a small LED visible through the case which
is used to indicate battery condition. You will notice a decrease in
transmitter range as the battery condition deteriorates. Transmit-
ter battery replacement is recommended at least every 10 to 12 months,
depending upon how frequently the transmitter is used.
To replace the battery:
1) Remove the small # 0 phillips head screw from the rear of the case.
2) Remove the rear cover to access the discharged battery paying
attention to the proper polarity orientation.
3) Carefully remove and properly dispose of the discharged battery.
4) Insert the new battery, close the case, then reinstall the small case
screw removed in step 1.
5) If you accidently dislodge the cir-
cuit board from the transmitter hous-
ing, be certain that the rubber mem-
brane is seated properly, and the
buttons are properly exposed from
the front view of the case, then
insert the circuit board, and return
to step #4.
5
128-6987
5 of 6
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERFORMFORAX-2K4 AX-2K4S,AX-2K4MS, AX-2K4MSFL
Attention: Transmitter Ordering
Department
Important: To help us expedite your
order, please print all of the infor-
mation legibly and mail this form
and your payment according to the
instructions below.
Indicate the pad number of your
transmitter selected from the pads
shown above.
Note: Transmitter model number
found on back of case.
AX-2K4MSFL Main use PD 110, Side use 111
1)Pad Number:_________________________________
2)Name: _______________________________________
3)Address: ______________________________________
4) City: ________________ State: _____ Zip Code: ________
5) Telephone Number: (_____) _______________
6) Total Number Of Transmitters Required:
Cost Per Transmitter is:
$65.00
Multiply By Number Of Transmitters
X ______
7) Enter Total Amount Enclosed _________________
(New York State Residents must include the appropriate sales tax)
8) Method of Payment:
Mastercard Visa Check or Money Order (do not send cash)
Make Checks Payable To Audiovox Corporation
Credit Card Number: _________________________________
Credit Card Expiration Date: ____ / _____ / _____
9) Mail this form along with your payment to:
Credit card purchasers can order additional or replacement
transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and
follow the instructions from the operator interface.
Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y., 11788
Attn.:TRANSMITTERDEPARTMENT
128-6987
© 2003 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY, 11788
128-6987
6 of 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|