Audiovox Automobile Electronics ACAM250 User Manual

2.5” LCD Backup Monitor  
Model: ACAM250  
Installation/User’s Manual  
Features:  
2.5” TFT color LCD display  
Flexible mounting pad with 3M tape monitor mounts on either  
vehicle windshield or dashboard  
Rearview camera input  
Automatically displays backup camera image when vehicle is in  
reverse  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Warnings  
1
2
3
3
6
6
7
8
Product description  
Packing list  
Installation Instructions  
Operation  
Maintenance  
Troubleshooting  
Warranty card  
Product Description  
This Rearview Mirror/Monitor, when used with a backup camera, is designed  
to assist the driver by providing a clear and wide image of the area behind the  
vehicle whenever the vehicle is shifted into reverse. Never rely solely on this  
product to ensure the area is clear of children and/or obstructions. Use your  
monitor and look both ways. This is not intended to replace existing safety  
procedures, but to add an additional safety tool for your vehicle.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Packing List  
Description  
Figure  
2.5” Monitor  
Power Cable  
Tap Connectors  
Alcohol Wipe  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
Mounting the Monitor  
The monitor with flexible mounting pad and 3M tape mounts on either the  
vehicle windshield or dashboard.  
1. Choose a monitor location in your vehicle that does not block your view  
for safe driving.  
2. Clean the monitor mounting area with the alcohol wipe provided.  
3. Remove the protective film from the 3M flexible adhesive mounting pad  
on the bottom of the monitor and carefully press into place.  
Note: Once pressed into place, the pad cannot be easily moved. Be sure of  
the position before mounting.  
4. Connect the power cable to the Monitor cable.  
5. Place (hide) the monitor cable behind the windshield trim piece and  
continue along under the head liner to the rear of the vehicle and into the  
truck, if applicable.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wiring the Monitor  
1. Wire the Power Cable to the vehicle’s reverse lamp.  
a) Locate the reverse lamp in the tail light assembly. Using the tap  
connector supplied, perform the following steps:  
i.  
Place the un-stripped positive lead wire on the run channel.  
Insert the un-stripped red power wire completely.  
ii.  
iii. Fold the tap connector back over the wires and make the  
connection by crimping the u-contact down flush with the  
plastic insulator.  
iv.  
Close the top hinged cover until latched.  
b) Attach the black wire to the ground.  
i.  
Place the un-stripped ground lead wire on the  
run channel.  
ii.  
Insert the un-stripped black ground wire completely.  
iii. Fold the tap connector back over the wires and make the  
connection by crimping the u-contact down flush with the  
plastic insulator.  
iv.  
Close the top hinged cover until latched.  
c) Connect the RCA video connector from the existing camera to the  
monitor cable.  
d) Connect the power supply plug from the existing camera to the  
monitor power DC plug (if your camera has a power plug).  
Tap Connection  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
The monitor will automatically display the rear observation camera image  
whenever the vehicle is engaged in reverse.  
Maintenance  
Though your Monitor requires little care, you can still maintain its condition  
and performance following the procedures below.  
Keep your system away from excessive moisture, extreme heat or cold  
and magnetic fields.  
Keep liquids away from the display monitor.  
To avoid damage, do not place auxiliary devices or other objects on the  
top of the monitor.  
Occasionally clean the surface of the monitor with soft cloth moistened  
with water or window cleaner.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Symptoms  
Solutions  
Ensure that the parallel red and black line from  
the control box is connected properly.  
The ON/OFF signal light  
<D> is not on after the car  
is started  
1. Verify  
that  
the  
LCD  
Contrast  
No video signal appears  
while reversing the car  
(Brightness) control knob is not set too  
low  
2. Check the rearview Camera lens.  
3. Check the rearview Camera wiring and  
connection.  
4. Confirm that the cable from the monitor  
is connected properly.  
Video image is not sharp Clean the camera lens.  
enough  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© 2008 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Aastra Telecom Answering Machine AVS 5150 User Manual
Accusplit Fitness Electronics 998 299B User Manual
Adaptec Personal Computer T645UK User Manual
Addonics Technologies Computer Drive ZESSIU3CS User Manual
ADTRAN Network Router 768 User Manual
Agri Fab Spreader 45 0324 User Manual
Atlas Model Vehicle 520099 User Manual
Atlona Building Set AT PC530 User Manual
Avenview TV Cables HDMI C5SP 4 User Manual
Beko Flat Panel Television 15LB250MID User Manual