Model APS-786T
Owner's Manual
4 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
FEATURES:
! 2 Four Button Programmable RF Transmitters (1 with Flashlight)
! Four Channel Code Learning Receiver (capable of accepting 4 transmitters)
! Code Hopping Technology
! Selectable Manual Override Mode
! Remote Panic in all modes
! Protected Valet/Override
! Remote Start Safety Control Switch
! Selectable Automatic Timed Start Mode
! User Programmable Manual Override Code
! 7 Function LED - Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming
! Intrusion Alert with Memory
! Audible Arm / Disarm / Defective Zone / Tamper Confirmation
! Instant Siren Activation All Entry Points
! Starter Disable When Armed
! True Last Door Arming
! Defective Zone By-Pass
! Active or Passive Arming Selectable
! Programmable Auto Lock On / Off
! Programmable Auto Unlock / Off/Drivers Door/All Doors
! Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec L/ Dbl. U/L
! Programmable Active or Passive Door Locks
! User Programmable Permanent Chirp Delete
! On Command RF Chirp Delete from Transmitter Or Selectable Through Software
! 6 Tone Multi Tone Siren
! Car Horn Activation for additional alarm response
! Additional Negative Trigger Input
! RF Inhibit with ignition on
! Parking Light Flasher
! Remote Keyless Entry With Optional Access Guard (must have power door locks)
! Illuminated Entry
! Plug In Dual Stage Shock Sensor
OPTIONS :
! Telematic Upgrade Ready
! Remote Trunk Release (must have electronic trunk release)
! Multiple Vehicle Capable
! Remote Power Window Roll Up
! Remote Garage Door Interface
! Multiple Vehicle Capable
CAUTION ! Be certain that the vehicle is outdoors before using this or any remote vehicle
starting device. A running engine produces dangerous carbon monoxide fumes
which can be harmful or fatal if prolonged exposure occurs. DO NOT remote
start the vehicle if it is garaged.
Released: 6-28-04
128-7180
1 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
ARMING THE SYSTEM - PASSIVE (AUTOMATIC)
If the passive arming feature has been selected:
1. Turn the engine off, exit the vehicle, and close all doors, hood and trunk.
The dash mounted LED will begin to flash rapidly indicating that the 30 second passive
arming timer has begun. If the LED does not begin to flash rapidly, then you have left a door,
hood, or trunk ajar. Closing this entry point will allow the arming cycle will begin. If any entry
point is opened during the 30 second arming cycle, arming will be suspended. When all entry
points are closed, the arming cycle will begin again.
At the end of the 30 seconds, the parking lights will flash once, the siren will chirp once, and
the dash mounted LED will begin to flash slowly confirming the system is armed. If the siren
did not sound when arming, then the chirps have been turned off. Refer to the section on
"Eliminating the Arm/Disarm Chirps" shown later in this manual. Passive door locking is a
selectable feature. If you have the optional door lock/unlock circuit installed, the doors may
or may not lock passively depending upon the setup during installation.
PROTECTION WHILE THE SYSTEM IS ARMED:
Opening any protected entry point, hood, trunk, or doors will cause the alarm to trigger
immediately. The siren will sound and the parking lights will flash for 30 seconds, then stop
and continue to monitor all protected entry points. If the thief left the door opened, the unit
will sound for six 30 second cycles then shut down, isolate the triggered zone and continue
to protect all other zones.
Whenever the system is armed, the dash mounted LED will slowly flash. This serves as a
visual deterrent to a potential thief. This LED is a very low current light emitting diode, and
will not cause the battery to drain even if left unattended for long periods of time.
Whenever the system is triggered, the vehicle's parking lights will flash for the full siren
sounding period. Optional - whenever the system is triggered, the interior courtesy light will
flash for the full siren sounding period.
Whenever the system is armed, the vehicle starter circuit is disabled, and the vehicle will not
start with the ignition key.
Whenever the system is armed, any strong impact to the vehicle will cause the shock
detector to trigger the alarm. Any lesser impact will cause the pre-detect stage of the shock
sensor to emit a few short series of warning tones from the siren.
DISARMING THE SYSTEM
As you approach the vehicle, press and release the Disarm button on the keychain transmitter.
The parking lights will flash two times, the siren will chirp twice, and the dash mounted LED
will turn off.
If you have the optional door lock/unlock circuit installed, the doors will unlock. If you have
the optional entry illumination circuit installed, the interior light will turn on for 30 seconds or
until the ignition key is switched on.
NOTE: If the passive arming mode was selected at time of installation, the dash mounted LED
will start flashing rapidly indicating that the system is rearming. Opening any door will
suspend the automatic arming.
If the parking lights flashed three times, and the siren chirps four times, this indicates that the
alarm system was triggered during your absence. Before turning on the ignition key,
examine the dash mounted LED's flash pattern. The number of flashes identifies the trig-
gered zone. For additional information, refer to INTRUSION WARNING SIGNALS found later
in this manual.
If the siren did not sound upon disarm, then the chirps have been turned off. Refer to the
sectiontitledELIMINATINGTHEARM/DISARMCHIRPS.
Page 3
128-7180
3 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button
is activated, the drivers door only will unlock, pressing the unlock button a second
time will cause all doors to unlock. If your transmitter has a sperate lock unlock
buttons, pressing the unlock button anytime after the first unlock command will cause
all the vehicle doors to unlock.
SILENTDISARMING
1. As you approach the vehicle, press and hold the disarm button of your key chain
transmitter for two seconds.
The parking lights will flash twice, and the dash mounted LED will turn off confirming that the
system is disarmed. The siren will not chirp. If you have the optional door lock/unlock circuit
installed, the doors will unlock. If you have the optional entry illumination circuit installed, the
interior light will turn on for 30 seconds or until the ignition key is switched on.
NOTE: If the passive arming mode was selected at time of installation, the dash mounted LED
will start flashing rapidly indicating that the system is rearming. Opening any door will
suspend the automatic arming.
If the parking lights flashed three times, and the siren chirps four times, this indicates that the
alarm system had been triggered in your absence. Before turning on the ignition key, examine
the dash mounted LED's flash pattern. The number of flashes identifies the triggered zone.
For additional information, refer to INTRUSION WARNING SIGNALS found later in this manual.
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button
is activated, the drivers door only will unlock, pressing the unlock button a second
time will cause all doors to unlock. If your transmitter has a sperate lock unlock
buttons, pressing the unlock button anytime after the first unlock command will cause
all the vehicle doors to unlock.
WHILETHESYSTEMISSOUNDING
If during a triggered state, you wish to shut off the siren without disarming your security
system, simply press and release any transmitter button other than the disarm button. This
action will turn off the siren yet leave the vehicle fully armed and protected. This feature is
particularly useful if you are aware of children playing near your vehicle that may accidently
trigger your security system. In this case you can cancel the siren sounding.
INTRUSIONWARNINGSIGNAL
This system will inform you if an intrusion attempt has occurred while you were away from
the vehicle. Upon disarm, the siren will chirp 4 times and the parking lights will flash 3 times.
Enter the vehicle and before turning on the ignition switch, observe the LED flash pattern.
If the LED flashes one time...pause, one time...pause etc., then an intrusion attempt was
made by impact or a strong vibration that the shock sensor detected. Check the vehicle for
possible damage to the glass or body panels.
If the LED flashes two times...pause, two times...pause etc., then an intrusion attempt was
made to open the hood, trunk, or by an accessory triggering device. Check the vehicle for
indications of forced entry to these openings.
If the LED flashes three times...pause, three times...pause etc., then an intrusion attempt
was made to the vehicle doors. Check all doors for indications of forced entry.
NOTE: The LED intrusion warning indications are stored in the system's memory and will be
erased when the ignition switch is turned on.
VALET PUSH-BUTTON SWITCH:
The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to
hand your transmitter to parking attendants or garage mechanics. When the system is in
valet mode, all alarm functions are bypassed, however the remote panic feature and remote
Page 4
128-7180
4 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
door locks will remain operational. To use the valet mode, the system must first be disarmed
either by using your keychain transmitter, or by activating your personalized manual override
code.
1. Enter the vehicle, and turn the ignition key to the on position.
2. Press and hold the valet pushbutton switch until the dash mounted LED turns on solid.
The system will remain in the valet mode.
3. To return to normal operation, press and release the pushbutton switch any time the
ignition is on.
NOTE: Always remember to return the vehicle to the valet off position. This will ensure that
the vehicle remains protected at all times.
MANUALLYOVERRIDINGYOURSYSTEM:
USINGTHEVALETPUSHBUTTONOVERRIDESWITCH
Your Security System can be disarmed without the use of the keychain transmitter. This is
necessary, since you will need the ability to operate your vehicle if the transmitter is lost or
its battery fails. If your system has been selected for Valet Switch manual override as
indicated on the last page of this manual, to by-pass the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the on position.
3. Within 5 seconds, press and release the valet/override pushbutton switch.
The alarm system will stop sounding and enter the (by-passed) mode. You can now start
and operate the vehicle normally.
Typically this override mode is used only if the transmitter has become inoperative.
Programming Your Custom Override Code:
Unlike override switches easily found, and defeated, this security system allows the con-
sumer to program a personal override code, offering a higher level of security. To take
advantage of this option, programmable feature # 10 must be selected for the Custom Code
Option. Consult your installation center for programming details. The system comes from the
factory with a pre-programmed override code of 11. To change this default override code,
do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency override
sequence. Turn the ignition switch to the on position.
2. Within 10 seconds, press and release the valet/override pushbutton switch, 3 times.
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing the
pushbutton switch from 1up to 9 times.
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on.
6. Within 10 seconds, begin to enter your chosen units digit by pressing and releasing the
pushbutton switch from 1 up to 9 times.
7. Finish by turning the ignition switch to the off position.
If the new code was accepted, the unit will report back the newly entered code, by flashing
the LED, first indicating the 10ths digit, pause and then the units digit. The unit will report the
new code three times with a one second pause between each code, then the system will
begin arming. If the LED flash pattern reports the previously stored code, the new code was
not entered correctly. Please repeat steps 1 through 7 above considering the following.
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero),
or no digit entered in any place, units or tenths.
Page 5
128-7180
5 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then
5 seconds during any of the above steps, the unit will revert back to the last
successfully stored code.
Custom Code Programming Example:
To Change the code from the factory pre-assigned code of 11 to “52” you would do the
following:
1. Disarm the system by use of the transmitter, or by use of the emergency override
sequence.
2. Turn the ignition switch to the on position.
3. Within 10 seconds, press and release the valet/override pushbutton switch, 3 times.
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
5. Within 10 seconds, begin to press and release the pushbutton switch to set the tenths
digit. (As per the example, press and release 5 times to set the tenths digit to 5)
6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off then on.
7. Within 10 seconds, begin to press and release the push- button switch to set the units digit.
(As per the example, press and release 2 times to set the units digit to 2).
8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern.
YouwillnotetheLEDflashingfivetimes, pause, andthenflashtwotimes, pause.Thispatternwillbe
repeated three times indicating the new code (52) has been accepted and stored in memory.
NOTE: If after step 7, the LED flashes a code other than what was just entered, this
indicates that the code has not been changed. You will have to repeat steps 1
through 7 above being certain to note the following:
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no
digit entered in any place, units or tenths.
NOTE: If15secondsofinactivityexpire, oriftheignitionswitchisturnedoffformorethen5seconds
during any of the above steps, the unit will revert back to the last successfully stored code.
MANUALLYOVERRIDINGYOURSYSTEM:
USINGTHECUSTOMCODEOVERRIDE
Assuming the override code programmed has not been changed, and the default override
code of 11 is in the system's memory.
1) Enter the vehicle and turn the ignition switch to the on position.
NOTE: The siren will sound.
2) Within 5 seconds, press and release the pushbutton switch 1 time.
3) Within 5 seconds, turn the ignition switch off then on.
4) Within 5 seconds, press and release the pushbutton switch 1 time.
5) Turn the ignition switch off then on and start the vehicle.
NOTE: If you have changed the programmed override code then substitute your new code
tenths for step 2 above, and units for step 5 above.
ELIMINATING THE NORMAL ARM/DISARM CHIRPS
You can selectively eliminate the normal arm & disarm chirps by holding the transmitter button
slightly longer when arming or disarming. This will prevent the siren chirps for one arm or
disarm cycle. If you find this inconvenient and wish to eliminate these chirps permanently,
1. Turn the ignition switch 'on" then 'off".
3. Within 10 seconds of turning off the ignition, press and release the valet push button
switch 3 times.
4. If the chirps were on before you started, the siren will emit 2 short chirps indicating that
Page 6
128-7180
6 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
the chirps are now off. If the chirps were off before you started, the siren will emit one
short chirp indicating that the chirps are now on.
NOTE: If the vehicle battery is disconnected then reconnected, the unit will return to the
default setting of chirps on. Repeat the above procedure to eliminate the arm/disarm
chirps.
REMOTEPANICOPERATION
The Lock or Unlock button on your keychain transmitter also functions as a panic switch for
use in emergency situations. To use remote panic,
1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more
seconds. The alarm will immediately sound.
2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter again for 3
seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds.
Also if any transmitter button other than the Lock or Unlock button is pressed and
released, the Panic mode will be turned off immediately. The normal function of this
transmitter button will be suspended during the Panic sounding period.
NOTE: While in the Panic mode, pressing and releasing the Lock, or the Unlock buttons will,
if the option is installed, lock and unlock the doors respectively. While in the panic
mode, anytime the unlock button is pressed, the panic feature will continue for the
allotted 30 seconds, however, the security system will be disarmed allowing the
vehicle to start.
SAFETY (Red Handled ) CONTROL SWITCH
The control switch allows you to temporarily disable the remote starting function of your
system. To disable the unit, move the red handled control switch to the off position.
The control switch also allows you to select between 2 hour start up and 4 hour start up
when using the automatic start up timer mode. The factory preset start up time for this mode
is every 4 hours. To select between 2 or 4 hour start up timer:
1. Begin with the control switch in the on position
2. Turn the ignition switch on then off
3. Within 10 seconds, move the control switch off, on, off, on (2 switch cycles) to select a
2 hour start timer. After 10 seconds expire, the parking lights will flash and the siren will
chirp 2 times confirming that the two hour start cycle is set. Or, within 10 seconds move
the control switch off, on, off, on, off, on, off, on (4 switch cycles) to select a 4 hour start
timer. The parking lights will flash and the siren will chirp four times confirming that the
four hour start timer is set.
REMOTESTARTINGTHEVEHICLE
The unit WILL NOT start the vehicle if any one of the following conditions exists:
1. The Vehicle Hood Is Opened.
2. The Gear Selector Is In Any Gear Other Then Park.
3. The Brake Is Depressed.
4. The Safety Control Switch Is In The Off Position.
CAUTION! Be certain that the vehicle is outdoors before using this or any remote vehicle
starting device. A running engine produces dangerous carbon monoxide fumes
which can be harmful or fatal if prolonged exposure occurs. DO NOT remote
start the vehicle if it is garaged.
To Remote Start The Vehicle:
Press and release the trunk/key button of your keychain transmitter two times within 2
seconds. The vehicle will start and remain running for the pre-programmed 5, 10, 15, or 20
Page 7
128-7180
7 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
minutes. As a visual indication, the parking lights will flash or turn on depending on the
programming set up by your installation center.
When you arrive at your vehicle, disarm the alarm system by pressing and releasing the
Disarm button of your keychain transmitter. Enter the vehicle and turn the ignition key to the
on position.
CAUTION! Do not turn the key to the start position. This will cause the starter motor to
engage with the already running engine which could result in damage. Step on
the brake pedal to disengage the remote start unit. The vehicle will continue to
run but now on it's own power.
NOTE: The engine will stop running before the expiration of the pre-programmed run timer if
you complete any of the following:
1. Press and release trunk/key button of your keychain transmitter two times within 2
seconds.
2. Depress the brake pedal.
3. Open the hood.
4. Move the red handled control switch to the off position.
5. Race the engine to above 4000 RPM.
OPERATING ONAUTOMATIC START UP TIMER MODE
The APS-785 has the ability to automatically start the vehicle every 2 or 4 hours over a 48
hour period. This feature is especially useful in cold climates where the only means to keep
the engine and engine fluids warm is to periodically start the engine.
CAUTION! Be certain that the vehicle is outdoors before using this or any remote vehicle
starting device. A running engine produces dangerous carbon monoxide fumes
which can be harmful or fatal if prolonged exposure occurs. DO NOT remote
start the vehicle if it is garaged.
TO BEGIN THEAUTOMATIC START UP TIMER
1. Turn the ignition key on then off.
2. Within 10 seconds, activate the RF start command two times. (Push the trunk/key button
of your keychain transmitter 4 times).
The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is
activated.
The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for the pre-pro-
grammed time (5,10,15 or 20 minutes), and then shut off. This will continue for 48 hours.
NOTE: The automatic start up timer can also be initiated from the keychain transmitter.
To do this:
1. Start the vehicle using the keychain transmitter by pressing and releasing the trunk/key
button 2 times.
2. Shut off the vehicle using the keychain transmitter by pressing and releasing the
trunk/key button 2 times.
3. Within 10 seconds of step 2, activate the RF start command two times. (Push the
trunk/key button of your keychain transmitter 4 times).
The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is
activated.
CANCELING THEAUTOMATIC START UPTIMER
To cancel the automatic start up timer do one of the following:
1. Start the vehicle manually with the use of the ignition key and depress the brake pedal.
2. Remote start the vehicle using your keychain RF transmitter.
Page 8
128-7180
8 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONALREMOTEFUNCTIONCHANNEL3
The system has an additional feature, (Channel 3) ,that can be connected to a number of
different optional accessories. Some of the more common uses for this channel are:
"Remote Trunk Release
"Remote Window Close
"Remote Garage Door Interface
To operate the accessory associated with channel 3, press and hold the trunk/key button(s)
of your keychain transmitter for four seconds.
NOTE: The feature that has been added to channel 3 will always be operated using the
same transmitter button that controls the remote start unit. There is no way to move
the channel 3 function to a different channel.
ADDITIONALREMOTEFUNCTIONCHANNEL4
The system has an additional feature, (Channel 4) ,that can be connected to a number of
different optional accessories. Some of the more common uses for this channel are:
"Remote Trunk Release
"Remote Window Close
"Remote Garage Door Interface
To operate the accessory associated with channel 4, press and release the Option button(s)
of your keychain transmitter. Note: The channel 4 output will remain active for as long as the
transmitter button(s) are held. Certain accessories may take advantage of the extended
output capability of this channel. Check with your installation center for operation of the
accessory that may be connected to channel 4.
TELEMATICUPGRADE:
This system has the ability to have a telematic upgrade module connected to it.
This is an upgrade that can give you control of certain functions of your vehicle
from a Telephone, or in some cases a computer interface. Please check with
your installation center for most recent Telematic Upgrades. If you had a Telematic
Upgrade installed, the manual supplied with the upgrade unit will provide a op-
erators manual advising of the features of the system and means available to
control these features of your vehicle.
Page 9
128-7180
9 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Page10
128-7180
10 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
APS-786T
SYSTEM FUNCTIONS AT A GLANCE
ALARM DASH LED INDICATORS
RAPID FLASHING
SLOW FLASHING
OFF
=
=
=
=
=
=
=
PASSIVEARMING
ARMED
DISARMED
ON SOLID
VALET MODE
3 FLASH... PAUSE
2 FLASH...PAUSE
1 FLASH...PAUSE
INTRUSION ZONE 3
INTRUSION ZONE 2
INTRUSION ZONE 1
ALARM SIREN CHIRP INDICATION
1 CHIRP*
2 CHIRPS*
3 CHIRPS
4 CHIRPS
5 CONTINUOUS
=
=
=
=
=
ARM
DISARMED
ARMING WITH ENTRY POINT OPENED
DISARMAFTER INTRUSION
TRIGGERED/PANIC
ALARM PARKING LAMP INDICATIONS
1 FLASH
2 FLASH
3 FLASH
CONTINUOUS FLASH
=
=
=
=
ARM
DISARM
DISARMAFTER INTRUSION
TRIGGERED/PANIC
REMOTE START SIREN INDICATIONS
1 LONG/1SHORT
=
RF START COMMAND ISSUED
(IF SELECTED ON)
REMOTE START PARKING LAMP INDICATIONS
1 FLASH
ON
=
=
RF START COMMAND ISSUED
RUNNING UNDER REMOTE START
CONTROL (IF SELECTED)
CONTINUOUS FLASH
=
RUNNING UNDER REMOTE START
CONTROL (IF SELECTED)
Page11
128-7180
11 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2004 Audiovox Electronics Corporation, Hauppauge, NY 11788
Page12
128-7180
128-7180
12 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
|