Audiovox Automobile Alarm CA 6552 User Manual

PROFESSIONAL  
SERIES  
Owner’s Guide  
For Models:  
ca 6552  
ca 6552 SST  
Deluxe Vehicle Security and  
Remote Start System with 2 Way  
Confirming LCD Remote Control  
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is  
applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR  
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Your Remote Control  
Arming the Security System  
To arm the system, exit the vehicle, close all doors, then press the button. The  
parking lights will flash 2 times, indicating the system is armed, has locked the  
doors (if equipped and connected) and activated the starter disable feature. The  
LED status indicator will blink steadily, once per second.  
NOTE: The system is equipped with a feature called Silent Choice. If enabled, the  
system requires a second press of the  
response from the vehicle.  
button to activate an audible arming  
Passive Arming Bypass  
If passive arming is enabled on your system, while the system is disarmed, press  
, the system will respond with 1 chirp and the LED will turn on. The  
security system will remain in this temporally bypassed state for as long as you  
+
wish. To exit passive bypass, press the  
to normal status.  
or button and the system will return  
Bypassing The Shock Sensor  
To arm the system and ignore the shock sensor press  
button, then within 5  
seconds press , the system will respond with 1 long chirp.  
+
NOTE: The system will only change the shock sensor setting for one arm cycle  
and will be defaulted back to normal operation the next time the system is armed.  
Hidden Alarm Function  
Press the  
button first, within 3 seconds press the  
button to activate the  
hidden alarm function. The security system will arm with “Hidden Alarm Function”  
in which the siren / horn will be silenced if the system is triggered.  
Disarming the Security System  
To disarm the system press the button. The parking lights will flash 1 time,  
indicating the system is disarmed and has unlocked the doors (if equipped and  
connected).  
NOTE: The system is equipped with a feature called Silent Choice. If enabled, the  
system requires a second press of the button to activate an audible disarming  
response from the vehicle. If your system is set up for 2 step unlock, a third press  
of unlock will activate the audible response.  
*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more  
than 2 seconds.  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Two Stage Door Unlock (Optional)  
If this feature is enabled on your system, pressing the  
button one time will  
unlock only the driver’s door. Press again within three seconds to unlock the  
remaining doors.  
Activating the Trunk Release Feature (Optional)  
If this feature is enabled on your system, pressing and holding the button for 3  
seconds will open the vehicle’s trunk or hatch.  
Activating the AUX 1 Output (Optional)  
If this feature is enabled on your system, pressing the  
and buttons  
simultaneously will activate an optional feature. This feature can be programmed  
for a wide range of functions like power window or sunroof automation, please  
consult your installing dealer to determine the functionality of your system.  
Entering AUX Mode and Activating the Additional AUX 2 - 5 Outputs  
(Optional)  
To access the additional AUX outputs, AUX 2, AUX 3, AUX 4, and AUX 5, you must  
first enter the transmitters AUX Mode. This will “shift” the functions of the  
transmitter buttons from their standard operation to control of the AUX outputs.  
AUX Mode - 1 Way transmitter: Press and Hold  
and  
for 2  
seconds, the transmitter LED will flash 1 time. AUX Mode will remain active  
for 15 seconds. AUX Mode will exit after 15 seconds of inactivity or by  
pressing  
and  
again for 2 seconds, the transmitter LED will flash 2  
times to confirm exit.  
AUX Mode - 2 Way transmitter: Press and Hold  
for 2 seconds, the  
transmitter LCD screen will display “AU”. AUX Mode will remain active  
for 15 seconds. AUX Mode will exit after 15 seconds of inactivity or by  
pressing  
again for 2 seconds.  
Activating outputs while in AUX Mode:  
AUX 2: Press and Hold  
AUX 3: Press and Hold  
AUX 4: Press and Hold  
AUX 5: Press and Hold  
for 3 seconds.  
for 3 seconds.  
for 3 seconds.  
for 3 seconds.  
4
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Progressive Car Finder Feature  
Press the  
button to locate your vehicle. The system will sound 5 times at low  
volume, increasing in volume each time the button is pressed.  
Using the Personal Protection Alarm (Panic)  
Press and hold the  
button for 3 seconds to activate the personal protection  
alarm. During panic mode, the normal function of the transmitter buttons will be  
suspended. The transmitter’s and buttons can be used to lock and unlock the  
door (if the option is installed). To stop the alarm, press and hold the  
button on  
the transmitter again for 3 seconds. The system will automatically stop after 30  
seconds.  
Programmed Transmitter Notification  
As a security precaution each time the vehicle’s ignition is turn on the status LED  
light with flash the number of transmitters programmed into the system. This helps  
to identify unauthorized transmitters from accessing your vehicle. If you believe an  
unauthorized transmitter has been programmed to your system, contact your  
installing dealer for assistance.  
Valet Mode  
When valet mode is activated the status LED will light solid, and all security  
functions will be disabled. To enter or exit valet mode simply follow the 4 steps  
outlined below:  
1.  
2.  
3.  
4.  
Turn the vehicle’s ignition ON.  
Push and hold the programming/valet button.  
The LED will turn on solid when valet mode is active  
Release the programming/valet button.  
Eliminating Arm / Disarm Notification Chirps  
System ARM/DISARM chirps can be toggled ON or OFF without entering the  
programming feature banks.  
1.  
2.  
Turn the ignition ON then OFF.  
Press and release the valet/programming button 3 times. The system  
will respond with 1 chirp for ON or 2 chirps for OFF.  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manually Overriding the Security System  
Your system can be disarmed without the use of the transmitter. This is  
necessary, since you will need the ability to operate your vehicle if the transmitter  
is lost or its battery fails. To by-pass the alarm system;  
1.  
2.  
3.  
Open the vehicle door. The alarm will sound.  
Turn the ignition key to the ON position.  
Within 10 seconds, press and release the valet push button switch.  
The alarm system will stop sounding and enter the (by-passed) mode. You can  
now start and operate the vehicle normally.  
Car Jack Mode  
This feature must be turned on in system programming, please consult your  
installing dealer.  
Triggering Car Jack mode: While the ignition is ON and press and hold  
+
for 2  
seconds, the parking lights will flash 1 time and the system will act as follows;  
1.  
50 seconds after being triggered the siren will chirp for 15 seconds,  
during this 15 seconds you will be alerted to push the valet button to  
turn off Car Jack mode. If Car Jack mode is not turned off at this time it  
will advance to the next step.  
2.  
3.  
Following the 15 second chirps (total time now 65 seconds) the siren  
will go into full sound and the parking lights will start flashing.  
90 seconds after trigger in, addition to the siren and parking lights, the  
system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS  
STATE UNTILTHE BATTERY IS DEPLETED.  
OVERRIDE THE SYSTEM TO TURN OFF CAR JACK MODE: Turn the ignition OFF  
then On and press the valet button within 10 seconds.  
6
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Your Remote Vehicle Starter  
Remote Starting Your Vehicle  
To activate the remote vehicle start function, press and release the  
button 2  
times within 2 seconds. The system will sound, the parking lights will flash 1 time  
and the system will check the vehicle to ensure it is safe to start. If all safety  
parameters are correct, the vehicle will start within 5 seconds. The vehicle’s  
parking lights will turn on (or flash depending on system settings) as a visual  
indication that the vehicle has started and is running.  
If your vehicle stalls or does not start, the system will pause 5 seconds, then try 2  
more times to start the vehicle (a total of 3 attempts). The system will pause 5  
seconds between each start attempt. If the vehicle does not start after the 3rd  
attempt, the system will abort the remote vehicle start process.  
Remote Start Shutdown  
Press and hold the  
button for 3 seconds to turn the vehicle off.  
Entering the Vehicle while it is Running via Remote Vehicle Start  
1.  
2.  
3.  
Unlock the vehicle’s doors.  
Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!  
Insert the key into the ignition switch and turn to the ON or RUN  
position.  
4.  
Press the brake pedal. The remote vehicle starter will disengage and  
the vehicle will operate normally.  
Preheating or Precooling the Vehicle’s interior  
Before exiting the vehicle, set the temperature controls to the desired setting and  
operation. After the system starts the vehicle, the heater or air conditioner will  
activate and heat or cool the vehicle’s interior to your setting.  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
User Programmable Run Time / Run Time Extension  
The system has the ability to allow the user to extend the time the vehicle will be  
running under control of the remote start. This will only extend the run time back to  
the current run time setting during the current remote start cycle. If your system is  
set to run 15 minutes and the time remaining is 4 minutes, extending the run time will  
reset the countdown timer to 15 minutes and your vehicle will continue to run for  
another 15 minutes. Follow the steps below to extend the vehicle’s run time.  
1.  
2.  
3.  
The remote start must already be active.  
Press and release the button 4 times.  
The system will chirp to confirm that the run time has been reset.  
Using the “Quick-stop” Feature  
If you want to make a short stop and keep your vehicle running (to keep the  
interior warm or cool), the quick-stop feature allows you to do this while keeping  
your vehicle secure and your keys with you.  
To engage quick stop:  
1.  
2.  
Stop the vehicle and place the transmission in PARK.  
With your foot off the brake pedal, press and release the  
button 2  
times within 2 seconds. The LED will flash 3 times to confirm quick  
stop is entered.  
3.  
Remove the keys from the ignition and exit the vehicle. Press the  
button to lock the vehicle’s doors if desired.  
Note: Do not leave children or animals unattended in the vehicle when using the  
quick-stop feature.  
Operating the 2 / 3 Hour Start Up Timer Mode  
The system has the ability to start the vehicle every 2 or 3 hours for a 48 hour  
period. This feature is especially useful in cold climates where the only means to  
keep the engine and engine fluids warm is to periodically start the engine. The  
default setting is 3 hour, Selection between 2 or 3 hour is made in option  
programming.  
WARNING!  
Be certain that the vehicle is outdoors before using this or any remote starting  
device. A running engine produces dangerous carbon monoxide fumes which  
can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the  
vehicle if it is garaged.  
8
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To begin the 2 / 3 hour start up timer mode:  
1.  
2.  
3.  
Turn the vehicle’s ignition ON then OFF.  
Press and hold the valet button.  
Press the  
button 4 times, the system will;  
a. When set for 3 Hour (default) - chirp 2 times and flash the  
parking lights 4 times.  
b. When set for 2 Hour - chirp 1 time and flash the parking  
lights 2 times.  
4.  
Release the valet button.  
To exit the 2 / 3 hour start up timer mode:  
1.  
Turn the vehicle’s Ignition ON.  
OR  
1.  
Activate the remote vehicle start feature using the remote control.  
Turbo Timer  
This option will keep the engine running to allow the vehicle’s turbo to properly cool  
down before shutting the engine off.  
To engage the Turbo Timer feature:  
1.  
2.  
3.  
4.  
With the vehicle running via the ignition key and your foot off of the  
brake pedal.  
Engage the vehicle’s parking brake and press the and  
buttons simultaneously.  
The vehicle’s parking lights will turn on to verify the Turbo Timer  
feature has been activated.  
Turn the ignition key OFF, the vehicle will continue to run until the pre-  
programmed time has elapsed (1, 3, or 5 minutes)  
To disengage the turbo timer feature, press the vehicle’s brake pedal.  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating the Daily Start Timer  
The system has the ability to start your vehicle based on a 24-hour countdown  
timer. This feature requires a two-part activation sequence. From the remote,  
pressing both the  
&
buttons together will activate the 24 hour countdown  
timer (the vehicle will start 24 hours from this time). Next, When you are finished  
operating the vehicle for the day, perform the following steps to complete the  
process.  
1.  
2.  
Turn the ignition ON/OFF (vehicle must be disarmed).  
Within 10 seconds, while pressing the brake, press and release the  
button twice.  
3.  
The vehicle will emit 2 chirps.  
Temperature Start Mode  
The system has the ability to start the vehicle if the temperature drops below a  
preset temperature threshold. Once activated, the system will only start the  
vehicle one time based on the temperature setting and will be cancelled if the  
vehicle is started with the key or remote started by the transmitter. Temperature is  
read from the module, located below the dashboard in most instances, and the  
vehicle’s interior temperature may vary from the ambient temperature.  
1.  
2.  
3.  
The vehicle must be armed.  
Press and release both the  
The vehicle will emit 1 chirp.  
&
buttons together.  
Note: This feature is defaulted OFF and must be set in option programming.  
Remote Start Safety Features  
For safety and security reasons, the system will shutdown or prevent the remote  
vehicle starter from activating if any of the following occur:  
1.  
2.  
The vehicle hood is open.  
The brake pedal is pressed prior to turning the ignition key to the ON  
position.  
3.  
4.  
The engine is over-revved (tach checking only).  
Valet mode is active.  
10  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LED and Siren/Horn Indications  
LED Display Indications  
LED  
Function  
OFF  
DISARMED  
SLOW FLASH  
FAST FLASH  
ON (SOLID)  
ARMED  
PASSIVEARMING  
VALET MODE  
2 FLASH... PAUSE  
3 FLASH... PAUSE  
4 FLASH... PAUSE  
5 FLASH... PAUSE  
ZONE 2 TRIGGER, HOOD/TRUNK  
ZONE 3 TRIGGER, DOOR  
ZONE 4 TRIGGER, SHOCK  
ZONE 5 TRIGGER, IGNITION  
Siren/Horn Indications  
Chirps  
Function  
1
2
3
4
5
DISARM  
ARM  
DOORAJAR UPONARMING  
DISARM / TRIGGERED  
CAR LOCATOR  
Parking Light Flash Indications  
Flashes  
Function  
1
DISARM  
2
ARM  
3
DISARM / TRIGGERED  
CAR LOCATOR  
REMOTE STARTED  
5
ON (SOLID)  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional 2-Way LCD Remote Control Functions  
Check Vehicle Status  
Press and release  
2 times then press  
within 3 seconds, the transmitter will  
display the current status of the vehicle.  
Display Illumination  
Press and hold the  
seconds.  
button for 1 second. The display will illuminate for 5  
Melody / Vibration Mode  
To have the remote control vibrate, play a melody tone or both each time it receives  
a response from the vehicle press and release  
seconds.  
then press and hold for 2  
Button Beeps  
To toggle button beeps on or off press and release  
seconds.  
then press and hold  
for 2  
Battery Save Mode  
While in POWER SAVE MODE the 2-way LCD transmitter will NOT look for any  
incoming signals from the main unit until a button is pressed. The LCD screen will  
display SAVE to indicate that power save mode is ON. To enter power save mode  
press and hold for 5 seconds.  
Clear Flashing Icons and Melody Sound  
Press the button 3 times within 3 seconds. This will clear the melody sound and  
flashing icons on the LCD screen.  
Stopping LCD Trigger Melody  
To stop the alarm trigger melody if the system has been triggered WITHOUT  
disarming the system, press any button one time only, this will not send a  
command to the vehicle at this time and the alarm will continue to sound.  
12  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Button Lock  
Press and release  
then press hold the for 2 seconds to toggle the button lock  
on or off. When the button lock is active, the remote control will beep/vibrate 2  
times when a button is pressed indicating it is locked.  
Illumination  
Press and release  
2 times then press and hold for 2 seconds to toggle  
illumination on or off. When on, the display will illuminate when it receives or  
sends a command.  
2 Car Mode  
To control a second security system enter 2 car mode by pressing then press  
and together for 3 seconds. When the  
icon appears on the transmitter’s LCD  
screen it will control the second security system. Use the same method to exit 2  
car mode and resume control of the original vehicle’s security system.  
NOTE: A second security system must be installed and the LCD transmitter must be  
learned to it before this feature will operate the additional system.  
Parking Meter Countdown  
The parking meter countdown timer has 6 preset times, to access the preset times  
and begin countdown press and release  
then press and hold  
for 2 seconds,  
each additional press of will increase the countdown time.  
Adjusting the Clock and Timer Settings  
The clock, alarm clock and programmable countdown timer are accessed through  
the Function Menu. Press and hold for 3 seconds to access the function menu,  
once you have accessed the feature menu press and release to scroll through  
each feature and follow the steps below to adjust the settings for each. Press and  
hold for 2 seconds to exit the menu.  
Clock Hour  
Press  
Press  
Press  
Press  
Press  
Press  
Press  
to increase or  
to increase or  
to increase or  
to increase or  
to decrease  
to decrease  
to decrease  
to decrease  
Clock Minute  
Alarm Clock Hour  
Alarm Clock Minute  
Alarm Clock ON / OFF  
Countdown Timer Hour  
Countdown Timer Minute  
to turn ON or to turn OFF  
to increase or  
to increase or  
to decrease  
to decrease  
Countdown Timer ON / OFF Press  
to turn ON or to turn OFF  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LCD Remote Control ICON’s  
UNLOCK  
LOCK  
VALET MODE  
SYSTEM ARMED  
IGNITION ON/TRIGGER  
TRANSMITTING  
TRUNK TRIGGER  
HOOD TRIGGER  
DOOR TRIGGER  
FULL SHOCK TRIGGER  
SYSTEM TRIGGER  
TIME COUNT DOWN  
BATTERY INDICATOR  
VIBRATE/SILENT MODE  
2 CAR MODE  
BATTERY SAVE MODE  
MELODY MODE  
TIME DISPLAY  
ENGINE RUNNING  
AUX MODE  
ALARM CLOCK  
TIMER / TEMP.  
START MODES  
AUX 2 OUTPUT  
AUX 1 OUTPUT  
AUX 3 OUTPUT  
AUX 5 OUTPUT  
AUX 4 OUTPUT  
14  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Transmitter Button Functions  
1 Way  
Transmitter  
Car Find /  
Panic  
Lock  
X
Unlock  
Start  
Operation Method  
Press and Release  
Lock  
Unlock  
X
X
X
Press and Release  
2 Step Unlock  
Trunk  
Press and Release 2 times  
Push and Hold (3 Sec)  
Press and Release  
Car Finder  
Panic  
X
X
Push and Hold (3 Sec)  
Press and Release (1 or 2 times  
depending on selectable option)  
Remote Start  
X
X
X
Remote Start  
Shutdown  
Push and Hold (3 Sec)  
Press and Release 4 times.  
Push and Hold (3 Sec)  
Run Time  
Extention  
AUX 1  
X
X
X
X
Press and Release Lock then  
Press Lock + Car Find  
Shock Bypass  
Hidden Alarm  
X
X
X
Press and Release Car Fnd then  
Press Lock  
Passive Arming  
Bypass  
X
X
Press and Release  
Press Unlock + Start  
Turbo Timer  
X
X
X
X
Ignition ON/OFF, Press and Hold  
Valet Button, Press Start 4 times  
2 / 3 Hour Start  
Daily Start Timer  
X
Press Lock + Start  
Temperature  
Start  
X
Press Unlock + Start While Armed  
AUX 2, 3, 4, 5 - Access in AUX Mode  
Press and Hold Find + Start  
Transmitter LED flashes 1 time  
Enter AUX Mode  
AUX 2  
X
X
X
Push and Hold (3 Sec)  
Push and Hold (3 Sec)  
Push and Hold (3 Sec)  
Push and Hold (3 Sec)  
AUX 3  
X
AUX 4  
X
AUX 5  
X
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2 Way  
Transmitter  
Car Find /  
Panic  
Lock  
X
Unlock  
Start  
Function Operation Method  
Press and Release  
Lock  
Unlock  
X
X
X
Press and Release  
2 Step Unlock  
Trunk  
Press and Release 2 times  
Push and Hold (3 Sec)  
Press and Release  
Car Finder  
X
X
Panic  
Push and Hold (3 Sec)  
Press and Release (1 or 2 times  
depending on selectable option)  
Remote Start  
X
X
X
Remote Start  
Shutdown  
Push and Hold (3 Sec)  
Press and Release 4 times.  
Push and Hold (3 Sec)  
Run Time  
Extention  
AUX 1  
X
X
X
X
Press and Release Lock then  
Press Lock + Car Find  
Shock Bypass  
Hidden Alarm  
X
X
X
Press and Release Car Fnd then  
Press Lock  
Passive Arming  
Bypass  
X
X
Press and Release  
Press Unlock + Start  
Turbo Timer  
2 / 3 Hour Start  
Daily Start Timer  
Menu  
X
X
X
Ignition ON/OFF, Press and Hold  
Valet Button, Press Start 4 times  
X
Press Lock + Start  
X
Press and Hold  
Temperature  
Start  
X
X
Press Unlock + Start While Armed  
AUX 2, 3, 4, 5 - Access in AUX Mode  
X
Press and Hold F for 2 seconds  
LCD displays AU  
Enter AUX Mode  
AUX 2  
X
Push and Hold (3 Sec)  
Push and Hold (3 Sec)  
Push and Hold (3 Sec)  
Push and Hold (3 Sec)  
AUX 3  
X
AUX 4  
X
AUX 5  
X
16  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacing Remote Control Batteries  
1 Way 4 Button Remote Control - ca6552 / ca6552SST  
The batteries inside each remote control should last approximately 1 year under  
normal use. When the batteries become weak you will notice the remote control  
range (the distance from the vehicle the remote control will work) deteriorate and the  
small LED on the remote control will dim. To replace the remote control batteries:  
1.  
2.  
3.  
4.  
Remove 3 screws and disassemble the halves of the remote  
control.  
Remove the old batteries, observing the +/- symbols on the  
batteries and replace with new batteries.  
Reassemble the halves of the remote control and install the 3  
screws.  
Test operation of the remote control.  
NOTE: The ca6552 uses 2 CR2016 batteries and the ca6552SST uses 1 CR2032.  
2 Way LCD Remote Control - ca6552  
The CR2450 battery inside the 2-way LCD remote control should last approximately 6  
months under normal use. When the batteries become weak you will notice the  
remote control range (the distance from the vehicle the remote control will work)  
deteriorate and the BATTERY icon on the LCD remote control will show.  
1.  
2.  
Gently slide the battery cover off of the remote control.  
Remove the old CR2450 battery, observing the +/- symbols on the  
battery, and replace with a new CR2450 battery.  
3.  
4.  
Gently slide the battery cover on to the back of the remote control.  
Test operation of the remote control.  
2 Way LCD Remote Control - ca6552SST  
The battery inside the 2 way LCD remote control is rechargeable, use the  
supplied battery charger to charge the battery until the battery icon on the  
LCD screen shows 3 bars indicating charging is complete. It is  
recommended that the battery be fully charged before normal use.  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Code Systems, Inc. Limited Lifetime Warranty  
Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE  
vehicle security product (the “Product”), purchased from an authorized CODE dealer, that (except as  
provided below) should this Product under normal use and conditions, be proven defective in  
material or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGI-  
NALLY INSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge for  
parts directly related to repairs of the defect(s).  
Switches, indicator lights, and transmitter cases are similarly warranted to the original  
purchaser for a period of one (1) year from the date of purchase of the Product.  
CODE accessories, sold separately, are covered by the applicable warranty accompa-  
nying the accessory.  
This warranty is non-transferable, non-assignable and is voided when: (1) the Product is  
removed from the vehicle in which it was originally installed; or (2) the vehicle in which the Product  
was originally installed is transferred to another party.  
This warranty does not apply to any product damaged by accident, physical or electrical  
abuse, improper installation, alteration, or use contrary to its intended function, fire, flood, or other  
natural acts.  
In order for the Product to be repaired or replaced under the terms of this warranty, the  
defective Product must be returned to an authorized CODE dealer and accompanied by a copy of  
the retail sales receipt. The date of purchase and year, make and model of the vehicle in which the  
Product was originally installed must be clearly indicated on the sales receipt.  
This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED  
OR IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MER-  
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE  
DURATION OF THIS WRITTEN WARRANTY. IN NO CASE SHALL CODE BE LIABLE FOR ANY  
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WAR-  
RANTY, EXPRESS OR IMPLIED, WHATSOEVER.  
CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF  
CODE’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT  
PROVIDED ABOVE AND, IN NO EVENT SHALL CODE’S LIABILITY EXCEED THE PURCHASE  
PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION  
LABOR.  
Some states do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation may not apply to you. This warranty gives you specific legal  
rights and you may also have other rights which vary from state to state  
18  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audiovox Electronics Corporation.  
Customer Service 1-800-421-3209  
WWW.CODE-ALARM.COM  
FCC COMPLIANCE  
This device complies with Part 15 of the FCC rules and with RSS-210 of  
Industry Canada. Operation is subject to the following two conditions:  
1. This device may not cause harmful interference, and  
2. This device must accept any interference received, including any interference  
that may cause undesired operation.  
Warning!  
Changes or modifications not expressly approved by the party responsible for  
compliance could void the user’s authority to operate the equipment.  
20  
ca6552/6552sst. 2011Audiovox Electronics Corporation.All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3M Cable Box 530 User Manual
ADC Network Router Fibre ETSI Solution User Manual
AG Neovo Computer Monitor DR 17 User Manual
Aigo Clock F029 User Manual
Airlink101 Network Card AWLC4030 User Manual
Altinex Network Card DA1926AV User Manual
American Audio CD Player MCD 710 User Manual
Avocent Personal Computer 3100 3200 User Manual
Bakers Pride Oven Food Warmer CSWG User Manual
Behringer Car Speaker B1220 PRO User Manual