Audiovox Automobile Alarm AA 930 User Manual

Model AA-930  
Two Button Code Learning  
Remote Alarm With Shock Sensor  
Installation & Operating Manual  
What Is Required For This Installation:  
1) A working knowledge of automotive mechanical and electrical systems.  
2) Electric Drill, 1/8” Drill Bit and (2) # 8 x 3/4” Sheet Metal Screws: To drill the mounting holes and secure  
the Siren Assembly to the vehicle.  
3) Electrical Tape: For insulating your wiring connections.  
4) (4) 6” Cable Ties: For routing the harness under the hood and inside the vehicle’s underdash area.  
Installation Of The Major Components:  
Installation Of The Major Components:  
Siren:  
Mount the Siren/Control Module in the engine compartment. The assembly should not be mounted within 8”  
of any hot surface. Also consideration should be made to keep the unit away from any moving parts, such  
as the steering shaft or knuckle, as this will interfere with safe operation of the vehicle. Use the siren  
bracket as a template and mark the two mounting holes with a pencil or scribe. Drill the two holes with a  
1/8” drill bit and secure the siren assembly to the location with two #8 screws.  
Wiring:  
RED FUSED WIRE: + 12 VDC CONSTANT BATTERY SOURCE  
Connect the red fused wire to a + 12 VDC constant battery source capable of supplying 5 amps of current. This  
wire provides power to the main alarm module.  
BLACK WIRE: CHASSIS GROUND  
Connect this wire to a solid, metal part of the vehicle’s chassis.  
Do not confuse this wire with the thin black antenna wire that exits the control module independently.  
Code Learning:  
In case the transmitter is lost, or you require additional transmitters, the code of the transmitter must be  
programmed into the receiver before it is capable of responding to the new or additional transmitters. Please  
perform the following procedure:  
a) With the system disarmed, disconnect then reconnect power to the alarm module, the siren will emit 3 chirp  
tones indicating the unit is ready to accept programming of up to 3 transmitters.  
b) Within 8 seconds, press any button of the transmitter to be programmed.  
NOTE: If no transmitter button is activated the unit will exit the program mode. Also, any time the program  
mode is entered and any transmitter is activated, all other transmitters will be erased. During the program  
sequence, you must have all transmitters present to be programmed that you wish to operate and activated  
one at a time during the program sequence. Each transmitter activated will cause the siren to chirp, once for  
the first, twice for the second, and three times for the third. If a fourth is attempted to be programmed, the first  
will be erased and the fourth will move the other two forward in the program.  
Arming The System:  
With the system disarmed, press the arm/disarm button once. The siren will chirp once and the LED will begin  
to flash, and the engine starter will be disabled. 5 seconds after the chirp, the system will be completely  
armed. During the armed mode, the unit can be triggered by shock/vibration, or a change in voltage such as  
the interior light turning on.  
Arming With The Two Stage Shock Sensor Bypassed:  
With the system disarmed, press the arm/disarm button once, the siren will chirp once. Within 5 seconds,  
press button 2 one time. The siren will emit one short chirp indicating the system is set and will be fully armed  
in 5 seconds with the shock sensor bypassed for one arming cycle. In this mode, the system cannot be  
triggered by the shock sensor. The only means of triggering is the voltage drop sensor.  
Arming With The Voltage Sensor Bypassed:  
With the system disarmed, press the arm/disarm button once, the siren will chirp once. Within 5 seconds,  
press button 2 two times. The siren will emit one long chirp indicating the system is set and will be fully armed  
in 5 seconds with the voltage sensor is bypassed. In this mode, the system cannot be triggered by a change  
in voltage. The only means of triggering is the shock sensor.  
In The Triggered Mode:  
When the system is armed, if the voltage drops, or a strong vibration is presented to the protected vehicle, the  
unit will trigger. When triggered, the siren will sound for 30 seconds then reset and continue to protect your  
vehicle. During the triggered mode, the unit can be reset by disarming with the transmitter or by use of the  
override method described later in this manual.  
Disarming The System:  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3Com Decking 09 1765 001 User Manual
Aastra Telecom IP Phone 6735I User Manual
Adcom Stereo Amplifier GFP 750 User Manual
AEG Refrigerator K 7 10 43 4 I User Manual
Agri Fab Spreader 45 0315 User Manual
Allied Telesis Switch Patch 89262 08 User Manual
Alpine Car Stereo System IVE W530BT User Manual
Alto Shaam Oven 610ESiN User Manual
American DJ DJ Equipment Sonic Beam II User Manual
Avenview TV Cables FO HDMI XX MM User Manual