Audiovox Automobile Alarm 128 8615 User Manual

Model APS-101N  
Installation Manual  
Programmable Features  
Select By Operating Transmitter  
Siren Indications  
1) Arming Method  
Press Lock Button  
1 Chirp  
Passive Arm  
Off  
Press Unlock Button  
2 Chirps  
Active Arm  
On  
Factory Default  
Passive Arm  
Off  
2) Ignition Control Lock/Unlock  
3) Passive Or Active Door Locks  
4) Single Or Double Pulse U/L  
5) Door Lock/Unlock Pulse Duration  
6) Siren Chirps On/Off  
Active  
Passive  
Double Pulse  
3 Seconds  
Off  
Active  
Single  
Single Pulse  
1 Second  
On  
1 Second  
On  
7) Passive Rearm From Active State  
On  
Off  
On  
To Program The Following Selectable Features:  
1. Enter the vehicle and turn the ignition key to the on position.  
2. Press and release the valet/override/program push button switch 3 times.  
Siren Chirps Once & Led Flash Once  
3. Within 3 seconds, turn the ignition off than on, you will hear short chirp followed by long chirp.  
4. Press and release the valet pushbutton switch one time to access feature #1. Use transmitter buttons to  
change, or press the valet pushbutton switch to advance to the next feature. Turn the ignition switch off, or allow 60 seconds of  
inactivity to exit the feature program mode.  
NOTE:  
While in the program mode, if the ignition switch is turned off, or if 60 seconds of inactivity expire the program mode will  
terminate, indicated by one short and one long chirp of the siren.  
INSTALLATION OF THE MAIN COMPONENTS  
Control Module :  
Select a mounting location inside the passenger compartment (up behind the dash), and secure using the two screws provided. The  
control module can also be secured in place using cable ties. Keep in mind that the module has the on-board Shock Sensor and should  
be mounted to a fairly rigid location to insure proper operation.  
Do not mount the control module in the engine compartment, as it is not waterproof. You should also avoid mounting the unit directly  
onto factory installed electronic components. These components may cause RF interference, which can result in poor transmitter  
range or intermittent operation.  
Siren:  
Select a mounting location in the engine compartment that is well protected from access below the vehicle. Avoid areas near high heat  
components or moving parts within the engine compartment. To prevent water retention, the flared end of the siren must be pointed  
downward when mounted.  
Mount the siren to the selected location using the screws and bracket provided.  
Hood or Trunk Pin Switch:  
A pin switch, not included, is intended for use in protecting the hood or trunk (or hatchback) of the vehicle. The switch must always  
be mounted to a grounded, metal surface of the vehicle. It is important to select a location where water cannot flow or collect, and to  
avoid all drip gutters on hood and trunk fender walls. Choose locations that are protected by rubber gaskets when the hood or trunk  
lid is closed.  
The pin switch can be mounted to a bracket, or direct mounting. Keep in mind that when properly mounted, the plunger of the pin switch  
should depress at least ¼ “ when the hood or trunk lid is closed.  
Dash Mounted LED:  
A small red LED is included that will serve as a visual indicator of the alarm status. It should be installed in the dash, located where it  
can be easily seen from outside the vehicle, yet not be distracting to the driver.  
128-8615  
1 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dark Blue Wire: DELAYED 200 mAPULSED OUTPUT / CHANNEL 2  
The dark blue wire pulses to ground via an independent RF channel from the keychain transmitter. This is a transistorized, low current  
output, and should only be used to drive an external relay coil.  
WARNING: Connecting the dark blue wire to the high current switched output of trunk release circuits, and some remote start trigger  
inputs, will damage the control module.  
In these cases connect the dark blue wire to terminal 86 of the AS-9256 relay (or equivalent 30 A automotive relay), and wire the  
remaining relay contacts to perform the selected function of channel 2.  
2 Pin White Connector: DASH MOUNTED LED  
Route the red and blue wires in the 2 pin white connector from the LED to the control module and plug it into the mating white connector  
on the side of the module.  
2 Pin Blue Connector: VALET / PROGRAMMING SWITCH  
Route the 2 pin blue connector from the override switch previously mounted to the mating two pin connector on the module.  
Red / Green / Red w/Black Trace 3 Pin White Connector: Door Lock Outputs  
The Red and Green wires will provide a pulsed ground output to the factory door lock control relay. The maximum current draw  
through these outputs must not exceed 200 mA. The Red w/Black trace wire will provide a pulsed ground when the unlock button of  
the transmitter is pressed a second time after a first unlock command was issued. This is used for second step unlock or all doors  
unlock in a two step circuit. In this arrangement Red or Green is used to control the drivers door unlock relay, and the Red/Black will  
be used to control unlock of all other doors.  
3 Wire Ground Switched Single Step Door Locks  
In this application, the red wire provides a ground pulse during arming, or the pulsed ground lock output. Connect the red wire to  
the wire that provides a low current ground signal from the factory door lock switch to the factory door lock control relay.  
The green wire provides a ground pulse during disarming, or the pulsed ground unlock output. Connect the green wire  
to the wire that provides a low current ground signal from the factory door unlock switch to the factory door unlock control relay.  
Red/Black Not Used.  
3 Wire Ground Switched 2 Step Door Locks  
In this application, the red wire provides a ground pulse during arming, or the pulsed ground lock output. Connect the red wire to  
the wire that provides a low current ground signal from the factory door lock switch to the factory door lock control relay.  
The green wire provides the first ground pulse during disarming, or the drivers door pulsed ground unlock output. Connect this  
wire to the drivers door unlock relay that requires a low current ground signal to unlock only the drivers door. If the vehicle does  
not have a separate drivers door relay, one will have to be added. Locate the drivers door unlock motor wire and cut it at a convenient  
location to allow wiring of an optional relay. Connect the door side of the cut wire to terminal 30 of the optional relay added. Connect  
the vehicle side of the cut wire to terminal 87a of the optional relay added. Connect the green wire of the 3 pin harness to terminal 86  
of the optional relay added. Connect terminal 85 of the optional relay added to a fused constant + 12 volt source. Most vehicles door  
lock/unlock motor legs rest at ground, and switch +12 volts to the door lock/unlock motor legs for operation, if this is the case in the  
vehicle you are working on, connect the remaining terminal, 87, to a fused + 12 volt source. In the rare instance that the vehicle door  
lock/unlock motor legs rest at + 12 volts and switches ground to the door lock/unlock motors, connect he remaining terminal, 87, to  
chassis ground.  
The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed a second time after  
disarming. Connect the Red/Black wire to the wire that provides a low current ground signal from the factory door unlock switch to  
the factory door lock control relay.  
Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt  
Door Lock Control Circuits  
These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS  
9159a Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the Audiovox fax back service for information  
on your particular vehicle for properly connecting to these types of circuits.  
Page 3  
128-8615  
3 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPLETING THE INSTALLATION  
NOTE: This unit has the ability to learn the dome light delay time, up to 60 seconds. If the vehicle has delay interior lights, and you  
wish to avoid three chirp, defect zone, indication normally associated with this type of interior light, we suggest you learn the  
interior light delay.  
To learn the light delay, start with all doors closed:  
(1) Use the transmitter to Lock / Unlock / Lock / Unlock / Lock / Unlock / Lock, the system.  
The LED turns on solid to confirm the system entered the learn mode.  
(2) Immediately open and close the door of the vehicle to initiate the dome delay.  
The unit will monitor the door trigger input Positive, (Purple), and Negative, (Brown) when active.  
When the dome light turns off, the unit will add 2 seconds then exit the learn mode.  
(3) The LED will begin flashing the Armed indication indicating the unit has exited the learn mode and is armed.  
Antenna Wire : Be sure to extend the thin black antenna wire to it’s full length, and cable tie into place where it cannot be damaged.  
Avoid wrapping this wire around major, high current wire looms.  
On-Board Shock Sensor Setting:  
1. Enter the vehicle, and turn the ignition key to the “on” position.  
2. Press and release the valet/override/program push button switch 3 times. Siren Chirps Once & Led Flash Once  
3. Turn the ignition off than on, you will hear short chirp followed by long chirp.  
4. Turn the ignition off then on, you will hear two long chirps indicating that you are in the shock adjust mode.  
5. Press the lock button to increase, and the unlock button to decrease. The siren will chirp 1-14 times 1 being lowest  
and 14 being highest. Firmly strike the bumper of the vehicle during the adjustment mode until you find the desired level for  
the Full Trigger Stage.  
6. Press both the lock & unlock buttons of the transmitter simultaneously until the siren emits two long siren chirps  
indicating that you are in the Pre-Detect adjust stage.  
7. Press the lock button to increase, and the unlock button to decrease. The siren will chirp 1-14 times 1 being lowest  
and 14 being highest. Firmly strike the bumper of the vehicle during the adjustment mode until you find the desired level for  
the Pre-Detect Stage.  
Once you have achieved the desired setting, either turn the ignition off or allow 60 seconds of inactivity to expire to exit the Shock  
Adjust Mode. Exit of the shock adjust mode is indicated by the siren emitting 3 long chirps.  
CAUTION: Never perform this test on the vehicle’s glass, as you may break the window.  
WARNING ! Setting the sensitivity too high can cause false alarms due to noise vibrations from passing trucks and heavy  
equipment. To decrease sensitivity, follow steps 1-5 above and use the trunk/key button to decrease.  
Wire Dressing: Always wrap the alarm wires in convoluted tubing, or with a spiral wrap of electrical tape. Secure these looms  
along the routing using cable ties. This will ensure that the alarm wires are not damaged by falling onto hot or sharp moving surfaces  
in the vehicle.  
Operation: Take a few moments to check off the appropriate option boxes in the owner’s manual, and to fully explain the operation  
of the system to your customer.  
Page 4  
128-8615  
4 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE LEFT BLANK INTENTIONALLY  
Page 5  
128-8615  
5 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Page 6  
128-8615  
6 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE LEFT BLANK INTENTIONALLY  
Page 7  
128-8615  
7 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© 2009AudiovoxElectronicsCorporation, 150MarcusBlvd., Hauppauge, NY11788  
128-8615  
Page 8  
128-8615  
8 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  

ACP EP Memory Computer Drive EPSNOW20 1GB B User Manual
AEG Dishwasher 5071 User Manual
Air King Fan 4CH68G User Manual
Airlink GPS Receiver EDGE GPRS User Manual
Allegro Multimedia Stud Sensor A1321 User Manual
Amana Microwave Oven RCS10DA User Manual
Atlantic Indoor Furnishings 144 DVD User Manual
Audiovox Car Stereo System ACD 13 User Manual
Audiovox Remote Starter APS 2K4 User Manual
Avet Reels Fishing Equipment Pro EXW 80 2 User Manual