Atlona HDMI 4 by 4 Matrix Switcher
over CAT5e/6/7
AT-PRO3HD44M
User Manual
Toll free: 1-877-536-3976
Local: 1-408-962-0515
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
With the latest and more affordable HDBaseT technology extend HDMI sources up to 200ft over
CAT5e/6 (230ft over CAT6a) at 1080p or 1920x1200. The Atlona HDMI 4 by 4 Matrix Switcher
allows for effortless control of up to 8 devices through IR remote control, RS-232, 3rd party IR
control box and the front panel. With a built in loop out S/PDIF port send audio to an AVR or
Distribution Amp. To ensure all audio passes through, the 4 by 4 Matrix Switcher supports all Lossy
and Lossless formats of Dolby and DTS over HDMI.
Package Contents
• 1 x AT-PRO3HD44M
• 1 x 24V/6.25A DC adaptor
• 1 x Power cord
• 1 x IR Extender
• 5 x IR Emitter
• 1 x Remote control
• 1 x Pair of dual purpose wall/rack mounts
• 1 x User Manual
IR Receiver
IR Emitter
Power Cord
Features
• HDBaseT allows IR, RS-232, audio and visual signals to pass over a single CAT5e/6/7 cable.
• IR ports for zone dedicated control through IR remote control and 3rd party IR controllers.
• Programmable I/O memories, save I/O routes for faster switching to the most commonly used
configurations.
• EDID learning function for up to 4 video display EDIDs.
• Multiple control options such as RS-232, IR, and the front panel.
• Dolby TrueHD and DTS-HD Master Audio pass through HDMI output interface.
• Compatible with DVI/D (with DVI/D to HDMI adapter such as AT-HD610), allowing DVI/D to be
passed to displays.
• Built in source Coax loop-out to send your audio to an AVR or Amplifier for easy audio
distribution. Compatible with PCM 2Channel, Dolby 2.0, Dobly Digital 5.1, and DTS 5.1.
• HDCP compliant
Toll free: 1-877-536-3976
Local: 1-408-962-0515
3
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
• Make sure when connecting the CAT5e/6/7 cables a 568B termination method is used.
• Make sure the matrix is connected to a component surge suppressor and line conditioner.
Note: Atlona’s warranty does not cover damage due to electrical disturbances. A component surge
suppressor and line conditioner are highly suggested especially in areas with electrical
storms.
• Be sure you’re using a mono to mono (2 conductor) 3.5mm IR cable (i.e. AT-MINIMONO6 -
available to purchase at Atlona.com) when using IR output control from 3rd party controllers,
stereo (3 conductor) 3.5mm cables are not compatible.
Specifications
Bandwidth frequency
Input Ports
6.75 Gbps
4 x HDMI (Female Type)
5 x IR 3.5mm
1 x Firmware update
4 x CAT 5e/6/7
Output Ports
4 x S/PDIF Digital Audio
1 x RS-232
5 x IR 3.5mm
Resolution outputs
Video: up to 1080p@60Hz
Vesa: up to 1920x1200
1.69x17.13x10 (inch) or 42.93x435.10x254 (mm)
7lbs or 3.18kg
Dimensions (HxWxD)
Weight
Power consumption
60W
Remote Control
Output selection. Numbers correspond with the CAT5e/6/7
category cable outputs (1-4) on the matrix.
Arrow buttons are not functional for this product.
Input selection. Numbers correspond with the HDMI inputs (1-4)
on the matrix.
Toll free: 1-877-536-3976
Local: 1-408-962-0515
4
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel Description
Front Panel
6
1
2
3
4
5
a
b
c
d
1. IR Receiver Window. Receives the signal from the included IR Remote Control or a 3rd party IR
Controller.
2. Power Button. Cycles the power between On (blue backlight) or Standby (red backlight) mode.
3. Function Button. Allows you to select command options. (blue backlight when selected)
a. Default: Mirrors all inputs to corresponding outputs. (i.e. 1 to 1, 2 to 2, 3 to 3, etc.)
b. All: Save a single input to all the outputs with this function.
c. Memory: Save/load the current input and output route to memory.
d. EDID: Save/Load EDIDs to individual inputs.
Note: Default setting for EDID is the highest common HD resolution of all connected
devices. (i.e. if you have resolutions ranging 720p, 1080i, and 1080p then 720p would be
the default resolution for all connected displays.)
4. Enter Button. Use to view current status for inputs and outputs or to confirm a command.
5. Cancel Button. Within the functions menu use to go back one screen or to the home screen.
Note: You cannot power off or change functions unless you go to the home screen.
6. Number buttons. Use these buttons to select input and output paths or use with the function
button to change multiple matrix settings.
Toll free: 1-877-536-3976
5
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Local: 1-408-962-0515
Back Panel
2
6
1
3
4
5
a
b
c
d
7
1. RS-232 - Connect to this port for control from a computer or 3rd party controller.
2. Matrix IR IN - Used to control matrix I/O switching from a 3rd party IR controller.
3. Matrix IR Out - Global output, combines IR for all discrete IR output ports.
4. Firmware Update - Type B USB Port used for updating the matrix firmware only
5. HDMI Input Ports - Connect HDMI sources into these ports, such as DVD players, Blu-ray players,
computers, etc.
6. Zone dedicated ports
a. IR 3.5mm mono In ports: Used in conjunction with 3rd IR party controller to extend IR
control commands to video displays over CAT5e/6/7.
b. IR Out ports: Sends IR signal to sources through a 3.5mm mono IR emitter
Note: Be sure you’re using a mono to mono 3.5mm IR cable (i.e. AT-MINIMONO6) for 3rd
party control boxes, stereo 3.5mm cables are not compatible.
c. Coax Out: Audio Loop-out for Amplifiers and AVRs.
Compatible with LPCM 2Channel, Dolby 2.0, Dobly Digital 5.1, and DTS 5.1.
d. CAT5e/6/7 Out: Extends video and bidirectional RS-232, IR, and audio signals through a
single CAT5e/6/7 cable.
7. Power Port - Use included locking DC adaptor to power the matrix switcher
Toll free: 1-877-536-3976
6
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Local: 1-408-962-0515
Connection and Installation
3rd Party Controller Set Up
Note: 3.5mm 3 conductor (stereo) cables are not compatible. Please use 2 conductor (mono) IR cables with IR input
ports.
Important: When using a 3rd party IR controller remember to connect a mono to mono 2 conductor IR
extender cable into the matrix IR IN port for IR control of the matrix switcher I/O.
Note: With the latest HDBaseT technology there’s no need for a power source for the extenders as they receive power
over the CAT5e/6/7 cable.
3rd Party Controller
Mono to
Blu-ray Player
mono 2
conductor
IR extender
cable
AT-PRO3HDREC
IR Emitter
Video Display
With the feature of the IR in ports the AT-PRO3HD44M has the unique ability to
receive IR commands through a 3rd party controller and send it out through the
CAT5e/6/7 port to control the displays in any zone.
Note: Be sure to use a mono to mono (2 conductor) 3.5mm IR extender from the
3rd party controller to the AT-PRO3HD44M (example: AT-MINIMONO6)
AT-MINIMONO6
Toll free: 1-877-536-3976
7
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Local: 1-408-962-0515
IR Remote Control Set Up
Note: When using an IR remote control all sources can be controlled as well as the local display.
Note: With the latest HDBaseT technology there’s no need for a power source for the extenders as they receive power
over the CAT5e/6/7 cable.
IR Emiꢀer
Blu-ray Player
AT-PRO3HDREC
IR Receiver
Module
Video Display
IR
Remote
Toll free: 1-877-536-3976
8
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Local: 1-408-962-0515
Matrix Front Panel Functions
The AT-PRO3HD44M’s front panel has 3 functions: I/O control, EDID set up, and matrix settings.
The following sections go over step by step control.
I/O Control
To set an input to an output
home screen
AT-PRO3HD44M
Select Input Number
Select output number
Press enter to confirm
--->
--->
--->
--->
Feedback =”Input # saved to
--->
--->
Output #”
To mirror all inputs and outputs
home screen
Select Function Option
Mirror In to Out
Press enter to confirm
AT-PRO3HD44M
Select Input Number
--->
--->
--->
--->
--->
--->
Feedback =”Mirroring In and Out”
To route one input to all outputs
home screen
AT-PRO3HD44M
--->
Select input number
to save to all outputs
Select Function Option
--->
--->
--->
Select Input Number
Input # to all outputs
Press enter to confirm
Feedback =
”Input # saved to all”
--->
--->
--->
--->
To save an I/O route to memory
home screen
AT-PRO3HD44M
Select Input Number
1 Save in/out route
---> --->
Select Function Option
--->
--->
--->
2 Select memory route
Feedback =
--->
Save to memory (1-4) #
Press enter
--->
--->
--->
”Memory # saved”
To load a saved I/O route
home screen
AT-PRO3HD44M
--->
1 Save in/out route
---> --->
Select Function Option
--->
--->
Select Input Number
2 Select memory route
Feedback =
”Memory # loaded”
Select Memory route 1-4
Press enter to load
--->
--->
--->
--->
Toll free: 1-877-536-3976
Local: 1-408-962-0515
9
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
EDID Set Up
When the matrix is completely connected and turned on it will load the default EDID, which is
the highest common native resolution of the devices. (i.e. With devices connected that range from
720p, 1080p, 2 channel audio, multi-channel audio and 3D, the default resolution will be 720p.
Multi-channel audio and 3D are not available on default unless all devices have these
features.)
There are two options when setting up EDID: Default and Copy. In order to have any options other
than default different EDIDs must first be copied. The AT-PRO3HD44M can copy up to 4 EDIDs to
memory.
To save an EDID
home screen
1 To copy up to 4 EDIDs
2 To choose input EDID
AT-PRO3HD44M
Select Input Number
Select Function Option
--->
--->
--->
--->
--->
Copy from output #
Save to Memory (1-4) #
Copy from output #
Save to Memory (1-4) #
--->
--->
--->
--->
Feedback=
”Saved port # EDID to
Memory # [Failed/Passed]”
--->
--->
To load a saved EDID
home screen
1 To copy up to 4 EDIDs
2 To choose input EDID
AT-PRO3HD44M
Select Input Number
Select Function Option
--->
--->
--->
--->
--->
Input #
Select an input port
Input # Press Enter
Current: Default
--->
--->
--->
--->
Input: # Select saved
EDID memory 1-4 (#)
Input: # Mode:
1. Default 2. Saved
--->
--->
--->
--->
--->
Feedback = ”Save memory # EDID
Use EDID memory # + enter
_ _ _
--->
--->
to input #”
EX. Atlona EDID - ATL
Pioneer EDID - PIO
Toshiba EDID - TSB
Toll free: 1-877-536-3976
Local: 1-408-962-0515
10
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Matrix Settings
When installing or troubleshooting it’s important to verify settings, or be able to come back to a
project and see how it was set up. The AT-PRO3HD44M has matrix settings viewable through the
front panel. View current I/O settings, firmware version, FPGA version, and the baud rates of not
just the matrix but extenders as well.
View I/O settings
home screen
AT-PRO3HD44M
Select Input Number
O 1
I x
2
x
3
x
4
x
--->
--->
View Firmware/Baud Rate/FPGA settings
home screen
AT-PRO3HD44M
Select Input Number
Select Function Option
Hold for
5 seconds
--->
--->
--->
--->
--->
EX. 115200 8 None 1
OR
AT-PRO3HD44M
Console: X X X X
AT-PRO3HD44M
FW Ver: 0.3.XX
--->
9600 8 ODD 0
Matrix Baud Rate
Repeat
AT-PRO3HD44M
Port 1: X X X X
AT-PRO3HD44M
Port #: X X X X
--->
--->
--->
--->
--->
--->
Output Baud Rate
AT-PRO3HD44M
FPGA 1 Ver: 0.0.XX
FPGA Version
Toll free: 1-877-536-3976
Local: 1-408-962-0515
11
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232
Connection
RS-232 is connected through a 9-pin female D connector. The pins will have functions associated
with them, some will be unassigned.
No.
1
Pin
----
Tx
Function
Not used
Transmit
Receive
5 4 3 2 1
2
3
Rx
4
----
Gnd
----
----
----
----
Not used
Ground
5
6
Not used
Not used
Not used
Not used
7
9 8 7 6
8
9
Command
The command codes are very sensitive, do not change capitalization, spacing, or lettering.
Command
PWON
PWOFF
PWSTA
Version
Lock
Feedback
PWON
Description
Power on
PWOFF
Power off
PWx
Will display the power status of the matrix (ex. Power is on = PWON)
Brings up the current firmware version
(Firmware #)
Lock
Locks the front panel of the matrix so no buttons are active
Unlocks the front panel of the matrix, enabling the buttons again
Resets all inputs to corresponding outputs (in3 to out3)
Turns off output channel (to turn off output 3 = x3$)
Switch input to output (input 3 to output 2 = x3AVx2)
Switch input to multiple outputs (input 3 = x3AVx1,x2)
Unlock
All#
Unlock
x1AVx1,x2AVx2,...
x1$
x1$
x1AVx2
x1AVx2,x3,x4
x1AVx2
x1AVx2,x3,x4
RS232zoneX[command] RS232zoneX[command] Send commands to devices connected to the receiver RS-232 ports.
Commands are the same as the ones stated in this table.
X = zone number
ex: RS232zone1[PWON] ex: RS232zone1[PWON] example: Turning the power on for the device connected in zone 1
Statusx1
Status
x7AVx1
Shows what input is connected to selected output
x1AVx1,x2AVx2,
x3AVx4, ....
Displays which inputs are currently connected to which outputs
SaveY (ex. Save2)
RecallY (ex. Recall2)
ClearY (ex. Clear2)
Mreset
SaveY (ex. Save2)
RecallY (ex. Recall2)
ClearY (ex. Clear2)
Mreset
Saves settings for future use, preset options 0 to 4
Recalls saved settings for the number you selected
Erases the save for the number you selected
Sets matrix back to the default settings
Each command or feedback is terminated with a carriage return.
Note: If the command fails or is incorrect the feedback should be “Command FAILED”
Toll free: 1-877-536-3976
Local: 1-408-962-0515
12
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 Set Up
To set up the RS-232 hyperterminal (if not using 3rd party software) the first thing needed is to find
the RS-232 communications port under the computer’s device manager. Once there right click the
port and select properties. Under the properties menu select the port settings tab and update the
menu to the matrix default: Bits Per Second: 115200, Data Bits: 8, Parity: None, Stop Bits: 1 and
Flow Control: None.
Baud Rate
To change the baud rate of the matrix or the receiver (AT-PRO3HDREC) an RS-232 hyperterminal
will be needed. Once the RS-232 hyperterminal is set up changing the baud rate will be done with
a command line. The baud rate for the matrix is for matrix control and the output baud
rate is for control of the RS-232 device in the zone being altered.
Note: Baud Rate must be only 2400, 4800, 9600, 19200, 38400, 57600, or 115200
Command for Matrix baud rate
CSpara[baudrate,data-length,parity,stop-bit] (data, parity, and stop for matrix must be 8,0,1)
For example if you wish to change the baud rate to 38400 the command would look like this:
CSpara[38400,8,0,1]
Toll free: 1-877-536-3976
13
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Local: 1-408-962-0515
RS-232 Command for the Output baud rate status
RS232para
The RS-232 status command will provide feedback for the current parameters for each output.
Example: (See example of feedback below)
RS232para
Current RS232 parameter:
- Port 1 :BaudRate 2400bps, DataBits 0, Parity None, StopBits 1.
- Port 2 :BaudRate 9600bps, DataBits 0, Parity ODD, StopBits 1.
- Port 3 :BaudRate 9600bps, DataBits 0, Parity None, StopBits 1.
- Port 4 :BaudRate 9600bps, DataBits 0, Parity None, StopBits 1.
Note: Default for the outputs is: Baud-9600bps, Data length-8bit, Parity-None, Stop Bit-1
The ability to check baud rate status on the outputs will help to identify control compatibility for in
zone RS-232 devices.
Command for Output (receiver) baud rate
RS232paraX[baudrate,data-length,parity,stop-bit]
X represents the zone# (output#), the data length must be 7 or 8, partity bit will be 0 for none, 1
for odd, 2 for even, and the stop-bit must be 1 or 2.
For example if you wish to change the baud rate to 19200, data length 8, ODD parity, and 1
stop-bit on the receiver in zone 3 to 19200 the command would look like this:
RS232para3[19200,8,1,1]
Toll free: 1-877-536-3976
14
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Local: 1-408-962-0515
Updating and Resetting
Updating firmware
At times there will be new firmware to update, fix, or change functionality of products. Atlona has
made this as easy as possible for updating on the job by simply downloading from Atlona.com and
uploading the file onto the matrix.
NOTE: Only use a Windows computer to update the matrix. Use of an Apple computer to update
will cause the matrix to be unusable until the update is redone with a Windows computer.
Needs:
• Verify the current firmware version
• RS-232 9 Pin to 9 Pin cable.
• PC (not compatible with MAC)
• OS that supports USB mass storage devices
• USB A to USB B cable (i.e. AT11008)
To view the current firmware use RS-232 command “Version”.
Preparing the Matrix:
• Unplug the power cable.
• Hold the Cancel button while plugging the power back in.
• Connect the USB B to USB A cable into the Matrix and the Computer.
Updating the Matrix:
The computer should auto detect the connection, if it does not, open the USB device from “my computer”.
• Click open in a new folder. (if auto run detects connection)
• Delete the file in the folder. (there should be only one file, if more delete all files)
• Copy and Paste the new firmware file into the USB folder.
• Unhook the Matrix from the computer.
• Unplug the power cable from the AT-PRO3HD44M
• Plug the power back in and start the matrix normally. Your update should be complete
If you wish to verify the new firmware, use the RS-232 command “Version”.
Resetting to factory settings
Atlona understands that settings can be troublesome and at times its just easier to set things back
to factory settings. To make things easier a simple one step reset was created.
To reset the matrix, hold down the buttons 1 and 4 while powering on. If done correctly the matrix
will be back to factory settings when it turns on.
Simultaneously
home screen
Reset to
Factory
Settings
Power LED should turn
RED to indicate the
Matrix is in standby
mode/off. Unplugging
then plugging back in
can also set the Matrix
into standby.
AT-PRO3HD44M
Select Input Number
--->
--->
--->
--->
---
---
Toll free: 1-877-536-3976
Local: 1-408-962-0515
15
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
Safeguards
Do not modify the wall plug. Doing so will
void the warranty and safety features.
To reduce the risk of electric shock, do not
expose this product to rain or moisture
This equipment should be installed near
the socket outlet and the device should
be easily accessible in the case it requires
disconnection.
If the wall plug does not fit into your local
power socket, hire an electrician to replace
your obsolete socket.
Precautions
FCC regulations state that any unauthorized changes or modifications to this equipment, not
expressly approved by the manufacturer, could void the user’s authority to operate this equipment.
Operate this product using only the included external power supply. Use of other power supplies
could impair performance, damage the product, or cause fires.
In the event of an electrostatic discharge this device may automatically turn off. If this occurs,
unplug the device and plug it back in.
Protect and route power cords so they will not be stepped on or pinched by anything placed on or
against them. Be especially careful of plug-ins or cord exit points from this product.
Avoid excessive humidity, sudden temperature changes or temperature extremes.
Keep this product away from wet locations such as bathtubs, sinks, laundries, wet basements, fish
tanks, and swimming pools.
Use only accessories recommended by Atlona to avoid fire, shock, or other hazards.
Unplug the product before cleaning. Use a damp cloth for cleaning and not cleaning fluid or
aerosols. Such products could enter the unit and cause damage, fire, or electric shock. Some
substances may also mar the finish of the product.
Never open, remove unit panels, or make any adjustments not described in this manual.
Attempting to do so could expose you to dangerous electrical shock or other hazards. It may also
cause damage to your AT-PRO3HD44M. Opening the product will void the warranty.
Do not attempt to service the unit. Disconnect the product and contact your authorized Atlona
reseller or contact Atlona directly.
Toll free: 1-877-536-3976
16
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Local: 1-408-962-0515
Warranty
Limited Warranty
Atlona Technologies warrants that (a) its products (AT-PRO3HD44M) will perform
substantially in accordance with the accompanying written materials for a period of 3 years from
the date of receipt and (b) that the product will be free from defects in materials and workmanship
under normal use and service for a period of 3 years. In the event applicable law imposes any
implied warranties, the implied warranty period is limited to 3 years from the date of receipt.
Some jurisdictions do not allow such limitations on duration of an implied warranty, so the above
limitation may not apply to customers that fall within those areas.
Customer Remedies
Atlona Technologies’ and its suppliers’ entire liability and Customer’s exclusive remedy
shall be, at Atlona Technologies’ decision, either return of the price paid for the product, repair,
or replacement of the product that does not meet this Limited Warranty and which is returned to
Atlona Technologies with a copy of the Customer’s receipt. This Limited Warranty is void if failure
of the product has resulted from accident, abuse, misapplication, or natural occurrence. In example
but not limited to: power surges (electrical storms, local power outage), dropping the product (or
items on the product), contact with fluids, and physical misconduct (i.e. kicking or punching). Any
replacement product will be warranted for the remainder of the original warranty period.
No other warranties
To the maximum extent permitted by applicable law, Atlona Technologies and its suppliers
disclaim all other warranties, either expressed or implied, including, but not limited to, implied
warranties of merchantability and fitness for a particular purpose, with regard to the product and
any related written materials. This Limited Warranty gives customer specific legal rights. Customers
may have other rights depending on the jurisdiction.
No liability for damages
To the maximum extent permitted by applicable law, in no event shall Atlona Technologies
or its suppliers be liable for any damages arising out of the use of or inability to use this product,
even if Atlona Technologies has been advised of the possibility of such damages. Such damages
include but are not limited to: special, incidental, consequential, or indirect damages for personal
injury, loss of business profits, business interruption, loss of business information, or any other
pecuniary loss. Atlona Technologies’ and its suppliers’ entire liability under any provision of this
agreement shall be limited to the amount actually paid by you for the product. Some Jurisdictions
do not allow the exclusion or limitation of liability for consequential or incidental damage. The
above limitations may not apply to you in such jurisdictional cases.
Toll free: 1-877-536-3976
17
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Local: 1-408-962-0515
Atlona Product Registration
Thank you for purchasing this Atlona product. - We hope you enjoy it and will take an extra
few moments to register your new purchase.
Registration creates an ownership record if your product is lost or stolen and helps ensure
you’ll receive notification of performance issues and firmware updates.
At Atlona, we respect and protect your privacy, assuring you that your registration information
is completely secure. Atlona product registration is completely voluntary and failure to register will not
diminish your limited warranty rights.
To register go to: http://www.atlona.com/registration
Toll free: 1-877-536-3976
18
atlona.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Local: 1-408-962-0515
|