26-Port Dual Web
Rack Switch
A02-F24-4G
USER’S MANUAL
A02-F24-4G_ME01
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Copyright
The Atlantis Land logo is a registered trademark of Atlantis Land SpA. All other names mentioned
mat be trademarks or registered trademarks of their respective owners. Subject to change without
notice. No liability for technical errors and/or omissions.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
FCC Warning
This equipment has been tested and found to comply with the regulations for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this user’s guide, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference, in which case the user
will be required to correct the interference at his own expense.
UL Warning
a) Elevated Operating Ambient Temperature- If installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment may be greater than room ambient. Therefore,
consideration should be given to installing the equipment in an environment compatible with the
manufacturer's maximum rated ambient temperature (Tmra).
b) Reduced Air Flow- Installation of the equipment in a rack should be such that the amount of air
flow required for safe operation of the equipment is not compromised.
c) Mechanical Loading- mounting of the equipment in the rack should be such that a hazardous
condition is not achieved due to uneven mechanical loading.
d) Circuit Overloading- Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of circuits might have on over current protection and
supply wiring. Appropriate consideration of equipment nameplate ratings should be used when
addressing this concern.
e) Reliable Earthing- Reliable earthing of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connections to the branch circuit
(e.g., use of power strips).
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
TABLE OF CONTENTS
CHAPTER 1............................................... 1
1.1 ABOUT THIS GUIDE ........................................................................................................................ 1
1.2 TERMS/USAGE ................................................................................................................................ 1
1.3 SWITCH FEATURES.......................................................................................................................... 1
Gigabit Ethernet Technology........................................................................................................... 1
Fast Ethernet Technology................................................................................................................ 2
Switching Technology...................................................................................................................... 2
VLAN (Virtual Local Area Network) ............................................................................................... 2
1.4 FEATURES ....................................................................................................................................... 3
CHAPTER 2............................................... 4
2.1 PACKAGE CONTENTS ...................................................................................................................... 4
2.2 INSTALLATION ................................................................................................................................ 4
2.3 RACK MOUNTING ........................................................................................................................... 4
2.4 CONNECTING NETWORK CABLE ..................................................................................................... 5
2.5 AC POWER ..................................................................................................................................... 6
2.6 IDENTIFYING EXTERNAL COMPONENTS .......................................................................................... 6
Front Panel...................................................................................................................................... 6
Rear Panel ....................................................................................................................................... 7
Understanding LED Indicators........................................................................................................ 7
CHAPTER 3............................................... 9
3.1 INSTALLING THE WEB MANAGEMENT UTILITY............................................................................... 9
3.2 WEB MANAGEMENT UTILITY ......................................................................................................... 9
Discovery List ................................................................................................................................ 10
Monitor List ................................................................................................................................... 11
Device Setting ................................................................................................................................ 12
Toolbar........................................................................................................................................... 13
CHAPTER 4............................................. 14
4.1 LOGIN ........................................................................................................................................... 14
4.2 SETUP MENU................................................................................................................................. 15
Port Settings................................................................................................................................... 15
VLAN Settings (Virtual Local Area Network)................................................................................ 17
Trunk Setting.................................................................................................................................. 18
4.3 MAINTENENCE.............................................................................................................................. 18
Status.............................................................................................................................................. 18
Statistics......................................................................................................................................... 18
System Settings............................................................................................................................... 20
TRAP.............................................................................................................................................. 21
Set Password.................................................................................................................................. 22
Backup Setting ............................................................................................................................... 22
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Reset Settings ................................................................................................................................. 23
Logout ............................................................................................................................................ 23
APPENDIX A........................................... 24
RJ-45 PIN SPECIFICATION................................................................................................................... 24
APPENDIX B........................................... 25
TECHNICAL SPECIFICATIONS............................................................................................................... 25
APPENDIX C........................................... 26
SUPPORT ............................................................................................................................................. 26
A02-F24-4G _ME01 (December 2004, V1.00)
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Chapter 1
Introduction
1.1 About This Guide
Congratulations on your purchase of the 24+4G-Port 10/100/1000Mbps Gigabit Ethernet Web Smart
Switch. This device integrates 1000Mbps Gigabit Ethernet, 100Mbps Fast Ethernet and 10Mbps
Ethernet network capabilities in a highly flexible package. This guide discusses how to install your
24+4G-Port 10/100/1000Mbps Gigabit Ethernet Web Smart Switch.
1.2 Terms/Usage
In this guide, the term “Switch” (first letter upper case) refers to your 24+4G-Port 10/100/1000Mbps
Gigabit Ethernet Web Smart Switch, and “switch” (first letter lower case) refers to other Ethernet
switches
1.3 Switch Features
This chapter describes the features of the 24+4G-Port 10/100/1000Mbps Gigabit Ethernet Web Smart
Switch and some background information about Ethernet/Fast Ethernet/Gigabit Ethernet switching
technology.
Gigabit Ethernet Technology
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format,
and support for CSMA/CD protocol, full duplex, flow control, and management objects, but with a
tenfold increase in theoretical throughput over 100-Mbps Fast Ethernet and a hundredfold increase
over 10-Mbps Ethernet. Since it is compatible with all 10-Mbps and 100-Mbps Ethernet environments,
Gigabit Ethernet provides a straightforward upgrade without wasting a company’s existing investment
in hardware, software, and trained personnel.
The increased speed and extra bandwidth offered by Gigabit Ethernet is essential to coping with the
network bottlenecks that frequently develop as computers and their busses get faster and more users
use applications that generate more traffic. Upgrading key components, such as your backbone and
servers to Gigabit Ethernet can greatly improve network response times as well as significantly speed
up the traffic between your subnets.
Gigabit Ethernet enables fast optical fiber connections to support video conferencing, complex
imaging, and similar data-intensive applications. Likewise, since data transfers occur 10 times faster
than Fast Ethernet, servers outfitted with Gigabit Ethernet NIC’s are able to perform 10 times the
number of operations in the same amount of time.
In addition, the phenomenal bandwidth delivered by Gigabit Ethernet is the most cost-effective
method to take advantage of today and tomorrow’s rapidly improving switching and routing
1
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
internetworking technologies. And with expected advances in the coming years in silicon technology
and digital signal processing that will enable Gigabit Ethernet to eventually operate over unshielded
twisted-pair (UTP) cabling, outfitting your network with a powerful 1000-Mbps-capable
backbone/server connection creates a flexible foundation for the next generation of network
technology products.
Fast Ethernet Technology
The growing importance of LANs and the increasing complexity of desktop computing applications
are fueling the need for high performance networks. A number of high-speed LAN technologies have
been proposed to provide greater bandwidth and improve client/server response times. Among them,
100BASE-T (Fast Ethernet) provides a non-disruptive, smooth evolution from the current 10BASE-T
technology. The non-disruptive and smooth evolution nature, and the dominating potential market
base, virtually guarantees cost-effective and high performance Fast Ethernet solutions.
100Mbps Fast Ethernet is a standard specified by the IEEE 802.3 LAN committee. It is an extension
of the 10Mbps Ethernet standard with the ability to transmit and receive data at 100Mbps, while
maintaining the CSMA/CD Ethernet protocol. Since the 100Mbps Fast Ethernet is compatible with all
other 10Mbps Ethernet environments, it provides a straightforward upgrade and takes advantage of the
existing investment in hardware, software, and personnel training.
Switching Technology
Another approach to pushing beyond the limits of Ethernet technology is the development of switching
technology. A switch bridges Ethernet packets at the MAC address level of the Ethernet protocol
transmitting among connected Ethernet or Fast Ethernet LAN segments.
Switching is a cost-effective way of increasing the total network capacity available to users on a local
area network. A switch increases capacity and decreases network loading by dividing a local area
network into different segments, which don’t compete with each other for network transmission
capacity.
The switch acts as a high-speed selective bridge between the individual segments. The switch, without
interfering with any other segments, automatically forwards traffic that needs to go from one segment
to another. By doing this the total network capacity is multiplied, while still maintaining the same
network cabling and adapter cards.
Switching LAN technology is a marked improvement over the previous generation of network bridges,
which were characterized by higher latencies. Routers have also been used to segment local area
networks, but the cost of a router, the setup and maintenance required make routers relatively
impractical. Today switches are an ideal solution to most kinds of local area network congestion
problems.
VLAN (Virtual Local Area Network)
A VLAN is a group of end-stations that are not constrained by their physical location and can
communicate as if a common broadcast domain, a LAN. The primary utility of using VLAN is to
reduce latency and need for routers, using faster switching instead. Other VLAN utility includes:
• Security, Security is increased with the reduction of opportunity in eavesdropping on a
broadcast network because data will be switched to only those confidential users within the
VLAN.
• Cost Reduction, VLANs can be used to create multiple broadcast domains, thus eliminating
the need of expensive routers.
• Port-based (or port-group) VLAN is the common method of implementing a VLAN, and is the
one supplied in the Switch.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
QoS
QoS gives you full control over which types of outgoing data traffic should be given priority by the
Switch, ensuring important data like gaming packets move through the Switch at lightning speed, even
under heavy load.
1.4 Features
Dual Web Rack Switch provides the following features:
• 24×10/100Mbps Auto-negotiation Fast Ethernet RJ45 ports
• 2×10/100/1000Mbps Auto-negotiation Gigabit RJ45 ports
• 2×mini-GBIC ports
• All RJ45 ports support auto MDI/MDIX, so there is no need to use cross-over cables or an up-
link port
• Full/half duplex transfer mode for 10/100Mbps RJ45 port
• Full duplex transfer mode for Gigabit port
• Wire speed reception and transmission
• Store-and-Forward switching scheme capability to support rate adaptation and ensure data
integrity
• Up to 4K unicast addresses entities per device, self-learning, and table aging
• 768KBytes packet buffer
• Supports IEEE 802.3x flow control for full-duplex mode ports
• Supports Back-pressure flow control for half-duplex mode ports
• Supports port-base VLAN
• Supports port-base QoS
• Supports Trunking on 1000BASE-T ports
• Supports Port-mirroring
• Supports Port-setting for Speed/Disable, Flow control
• Easy configuration via WEB Browser
• Easy setting via Web Management Utility
• Standard 19” Rack-mount size
3
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Chapter 2
Installation
This chapter provides unpacking and installation information for the Switch.
2.1 Package Contents
Open the shipping cartons of the Switch and carefully unpacks its contents. The carton should contain
the following items:
• 26-Port Dual Web Rack Switch
• One AC power cord, suitable for your area’s electrical power connections
• Four rubber feet to be used for shock cushioning
• Screws and two mounting brackets
• CD-Rom with Web Management Utility and User’s Guide
If any of the above items are missing, please contact your reseller.
2.2 Installation
The site where you install the hub stack may greatly affect its performance. When installing, consider
the following pointers:
• Install the Switch in a fairly cool and dry place. See Technical Specifications for the
acceptable temperature and humidity operating ranges.
• Install the Switch in a site free from strong electromagnetic field generators (such as motors),
vibration, dust, and direct exposure to sunlight.
• Leave at least 10cm of space at the front and rear of the hub for ventilation.
• Install the Switch on a sturdy, level surface that can support its weight, or in an EIA standard-
size equipment rack. For information on rack installation, see the next section, Rack Mounting.
• When installing the Switch on a level surface, attach the rubber feet to the bottom of each
device. The rubber feet cushion the hub and protect the hub case from scratching.
2.3 Rack Mounting
The switch can be mounted in an EIA standard-size, 19-inch rack, which can be placed in a wiring
closet with other equipment. Attach the mounting brackets at the switch’s front panel (one on each
side), and secure them with the provided screws.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Combine the Switch with the provided screws
Then, use screws provided with the equipment rack to mount each switch in the rack.
Mount the Switch in the rack
2.4 Connecting Network Cable
The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and it runs both in half and full
duplex mode using two pair of Category 5 cable.
The Switch also supports 2-Ports 1000Mbps Gigabit Ethernet that runs in Auto-negotiation mode and
10Mbps Ethernet or 100Mbps Fast Ethernet that runs both in half and full duplex mode and 1000Mbps
Gigabit Ethernet runs in full duplex mode using four pair of Category 5 Cable.
These RJ45 ports are Auto-MDI type port. The Switch can auto transform to MDI-II or MDI-X type,
so you can just make an easy connection that without worrying if you are using a standard or crossover
RJ45 cable.
There are additional two mini-GBIC ports for optional mini-GBIC module.
Product Code
Description
Standards
A02-MSW2(Fiber module)
Giga Ethernet Fiber Module
1000BASE-SX
Network Media
Connector
50µm or 62.5µm multimode optical fibers
LC
5
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Distance
Technology
Connector
10 Base T
100 Base TX RJ45
1000 Base T
1000 Base SX
1000 Base SX
RJ45
100m
100m
100m
275m
550m
RJ45
LC (62.5µm multimode optical fibers)
LC (50µm multimode optical fibers)
2.5 AC Power
The Switch used the AC power supply 100-240V AC, 50-60 Hz. The power switch is located at the
rear of the unit adjacent to the AC power connector and the system fan. The switch’s power supply
will adjust to the local power source automatically and may be turned on without having any or all
LAN segment cables connected.
2.6 Identifying External Components
This chapter describes the front panel, rear panel, and LED indicators of the Switch.
Front Panel
The figure below shows the front panels of the Switch.
28-Port 10/100/1000Mbps Web-SMART Gigabit Ethernet Switch
10/100M
Gigabit
1000BASE-T
1
2
3
4
5
7
8
9
11
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Mini GBIC
Link/ACT
POWER
SYSTEM
Link/ACT
1000Mbps
10
12
100Mbps
100Mbps
26-Port Dual Web Rack Switch
LED Indicator::
Comprehensive LED indicators display the status of the switch and the network (see the LED
Indicators chapter below).
Fast Ethernet Ports (Port 1~24):
These ports support network speeds of either 10Mbps or 100Mbps, and can operate in half- and full-
duplex transfer modes. These ports also supports automatic MDI/MDIX crossover detection function
gives true “plug and play” capability, just need to plug-in the network cable to the hub directly and
don’t care if the end node is NIC (Network Interface Card) or switch and hub.
When the port was set to “Forced Mode”, the Auto MDI/MDIX will be disabled.
Gigabit Ethernet Ports (Port 25~26)::
The Switch is equipped with two Gigabit twisted pair ports, supported auto negotiable
10/100/1000Mbps and auto MDI/MDIX crossover detection function. These two ports can operate in
half-duplex mode for 10/100Mbps and full- duplex mode for 10/100/1000Mbps.
When the port was set to “Forced Mode”, the Auto MDI/MDIX will be disabled.
Mini-GBIC Ports (Port 27~28):
6
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
The Switch is equipped with two mini-GBIC ports, supported optional 1000BASE-SX/LX mini-GBIC
module (1000BASE-SX mini-GBIC module).
Rear Panel
Power Switch:
This is a switch where you can control to enable or disable the power.
AC Power Connector:
This is a three-pronged connector that supports the power cord. Plug in the female connector of the
provided power cord into this connector, and the male into a power outlet. Supported input voltages
range from 100-240V AC at 50-60Hz.
Reset:
The Reset button is to reset all the setting back to the factory default.
Note: Be sure that you recorded the setting of your device, else all the setting will be erased when
pressing the “Reset” button.
Understanding LED Indicators
The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when
needed.
28-Port 10/100/1000Mbps Web-SMART Gigabit Ethernet Switch
10/100M
Gigabit
26
27
3
4
5
7
9
13
14
15
19
23
25
28
1
11
17
21
Link/ACT
Link/ACT
POWER
1000Mbps
2
8
10
12
16
18
20
22
24
SYSTEM
100Mbps
100Mbps
Led POWER
On
: When the Power LED lights on, the Switch is receiving power.
Off
: When the Power turns off or the power cord has improper connection..
7
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Led SYSTEM
Blinking : When the CPU is working, the System LED is blinking.
On/Off : The CPU is not working.
Ports 1~24 10/100M Status LEDs
Link/ACT: Link/Activity
On
: When the Link/ACT LED lights on, the respective port is successfully connected to an
Ethernet network.
Blinking : When the Link/ACT LED is blinking, the port is transmitting or receiving data on the
Ethernet network.
Off
: No link.
100Mbps
On
: When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast
Ethernet network.
Off
: When the respective port is connected to a 10Mbps Ethernet network
Ports 25~26 Gigabit Status LEDs
Link/ACT: Link/Activity
On
: When the Link/ACT LEDA lights on, the respective port is successfully connected to an
Ethernet network.
Blinking : When the Link/ACT LED is blinking, the port is transmitting or receiving data on the
Ethernet network.
Off
: No link.
100Mbps
On
: When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast
Ethernet network.
Off
: When the respective port is connected to a 10Mbps Ethernet or 1000Mbps Gigabit Ethernet
network.
1000Mbps
On
: When the 1000Mbps LED lights on, the respective port is connected to a 1000Mbps Gigabit
Ethernet network.
Off
: When the respective port is connected to a 10Mbps Ethernet or 100Mbps Fast Ethernet
network
Ports 27~28 mini-GBIC Status LEDs
Link/ACT: Link/Activity
On
: When the mini-GBIC module is installed and connected to a network, the Link/ACT
LED lights on.
Blinking : When the LED is blinking, the mini-GBIC module is receiving data on a network.
Off
: No link.
1000Mbps
On
: When the 1000Mbps LED lights on, the respective port is connected to a 1000Mbps Gigabit
Ethernet network.
Off
: When the respective port is disconnected to the network
8
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Chapter 3
Configuration
Through the Web Browser you can configure the Switch such as VLAN, Trunking, QoS… etc.
With the attached Web Management Utility, you can easily discover all the Web Management Switch,
assign the IP Address, changing the password and upgrading the new firmware.
3.1 Installing the Web Management Utility
The following gives instructions guiding you through the installations of the Web Management utility.
1. Insert the Utility CD in the CD-Rom Drive.
2. From the Start menu on the Windows desktop, choose Run.
3. In the Run dialog box, type CDRom:\Driver\A02-F24-4G\setup.exe and click OK.
4. Follow the on-screen instructions to install the utility.
5. Upon completion, go to Program Files -> web_management_utility and execute the Web
Management utility.
3.2 Web Management Utility
The Web Management Utility was divided into four parts :
• Discovery List
• Monitor List
• Device Setting
• Toolbar function
for details instruction, follow the below section.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Discovery List
This is the list where you can discover all the Web management devices in the entire network.
By pressing the “Discovery” button, you can list all the Web Management devices in the discovery
list.
Double click or press the “Add to monitor list” button to select a device from the Discovery List to
the Monitor List.
System word definitions in the Discovery List:
• MAC Address: Shows the device MAC Address.
• IP Address: Shows the current IP address of the device.
• Protocol version: Shows the version of the Utility protocol.
• Product Name: Shows the device product name.
• System Name: Shows the appointed device system name.
• Location: Shows where the device is located.
• Trap IP: Shows the IP where the Trap to be sent.
• Subnet Mask: Shows the Subnet Mask set of the device.
• Gateway: Shows the Gateway set of the device.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Monitor List
All the Web Smart Device in the Monitor List can be monitored; you can also receive the trap and
show the status of the device.
System word definitions in the Monitor List:
• S: Shows the system symbol of the Web-Smart device,
alive.
represent for device system is not
• IP Address: Shows the current IP address of the device.
• MAC Address: Shows the device MAC Address.
• Protocol version: Shows the version of the Utility protocol.
• Product Name: Shows the device product name.
• System Name: Shows the appointed device system name.
• Location: Shows where the device is located.
• Trap IP: Shows the IP where the Trap to be sent.
• Subnet Mask: Shows the Subnet Mask set of the device.
• Gateway: Shows the Gateway set of the device.
View Trap: The Trap function can receive the events that happen from the Web Management Switch
in the Monitor List.
There is a light indicator behind the “View Trap” button, when the light indicates in green, it means
that there is no trap transmitted, and else when it indicates in red, it means that there is new trap
transmitted, this is to remind us to view the trap.
When the “View Trap” button is clicked, a Trap Information window will pop out, it will show the
trap information including the Symbol, Time, Device IP and the Event occured.
The symbol “ ” represents the trap signal arise, this symbol will disappear after you review and click
on the event record
11
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
In order to receive Trap information, switch has to be configured with Trap IP and
Trap Events in Web browser, which are available in the Trap Setting Menu
Add Item: To add a device to the Monitor List manually, enter the IP Address of the device that you
want to monitor.
Delete Item: To delete the device in the Monitor List.
Device Setting
You can set the device by using the function key in the Device Setting Dialog box.
Configuration Setting: In this Configuration Setting, you can set the IP Address, Subnet Mask,
Gateway, Set Trap to (Trap IP Address), System name and Location.
Select the device in the Discovery list or Monitor List and press this button, then the Configuration
Setting window will pop out as Figure below, after filling up the data that you want to change, you
must fill up the password and press the “Set” to process the data changed immediately.
Password Change: You can use this Password Change when you need to change the password, fill in
the password needed in the dialog box and press “Set” button to proceed the password change
immediately. The factory default password is "admin".
Firmware Upgrade: When the device has a new function, there will be a new firmware to update the
device, use this function to update.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Do NOT upgrade firmware on any Atlantis Land product over a wireless
connection.
Failure of the device may result. Use only hard-wired network connections.
Web Access: Double click the device in the Monitor List or select a device in the Monitor List and
press this “Web Access” button to access the device in Web browser.
Toolbar
The toolbar in the Web Management Utility have four main tabs : File, View, Options and Help.
• In the “File TAB”, there are Monitor Save, Monitor Save As, Monitor Load and Exit.
Monitor Save: To record the setting of the Monitor List to the default, when you open the Web
Management Utility next time, it will auto load the default recorded setting.
Monitor Save As: To record the setting of the Monitor List in appointed filename and file path.
Monitor Load: To manually load the setting file of the Monitor List.
Exit: To exit the Web Management Utility.
• In the “View TAB”, there are view log and clear log function, this function will help you to
show trap setting.
View Log: To show the event of the Web Management Utility and the device.
Clear Log: to clear the log.
• In the “Option TAB”, there are Refresh Time function, this function helps you to refresh the
time of monitoring the device. Choose 15 secs, 30 secs, 1 min, 2 min and 5 min to select the
time of monitoring.
• In the “Help TAB”, there is About function, it will show out the version of the Web
Management Utility.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Chapter 4
WEB Configuration
The 24+4G-Port 10/100/1000Mbps Gigabit Ethernet Web Smart Switch has a Web GUI interface for
smart switch configuration. The Switch can be configured through the Web Browser. A network
administrator can manage, control and monitor the switch from the local LAN. This section indicates
how to configure the Switch to enable its smart functions including:
• Port Setting (Speed/Disable, Duplex mode, Flow Control and Port base QoS)
• Virtual LAN Group setting (VLAN)
• Trunking
• Mirroring
• System Setting
• Device status and Statistic
4.1 Login
Before you configure this device, note that when the Web Smart Switch is configured through an
Ethernet connection, make sure the manager PC must be set on same the IP network. For example,
when the default network address of the default IP address of the Web Smart Switch is 192.168.0.1,
then the manager PC should be set at 192.168.0.x (where x is a number between 2 and 254), and the
default subnet mask is 255.255.255.0.
Open Internet Explorer 5.0 or above Web browser.
Enter IP address http://192.168.0.1 (the factory-default IP address setting) to the address location.
Or through the Web Management Utility, you do not need to remember the IP Address, select the
device shown in the Monitor List of the Web Management Utility to settle the device on the Web
Browser.
When the following dialog page appears, remain enter the default password "admin" and press Login
to enter the main configuration window.
After entering the password, the main page comes up, the screen will display the device status.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
4.2 Setup Menu
When the main page appears, find the Setup menu in the left side of the screen. Click on the setup item
that you want to configure. There are 4 options: Port Settings, VLAN Settings, Trunk Setting and
Mirror.
Port Settings
In Port Settings menu, this page will show each port’s status, press the ID parameter to set each port’s
Speed, Flow Control, and QoS priority. When you need to renew the posted information, press the
“Refresh” button.
The Link Status in the screen will show the connection speed and duplex mode; else this dialog box
will show down when the port is disconnected.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
To change the port setting, click on the ID parameter to enter to the selected port to configure its
Speed/Disable, Flow control and QoS setting.
Speed/Disable:
This setting has six modes: 100M Full, 100M Half, 10M Full, 10M Half, Auto and Disable.
Flow Control:
16
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
This setting determines whether or not the Switch will be handling flow control. Set FlowCtrl to
Enable for avoiding data transfer overflow. Or it sets to Disable; there is either no flow control or
other hardware/software management.
When the port is set to forced mode, then the flow control will automatically set to
Disable.
Sending packets between two groups may cause packet lost
QoS:
In some ports that need to have a high priority to manage the data transfer, QoS should be change. Set
the port’s QoS to high to determine the port will always transfer their data first.
VLAN Settings (Virtual Local Area Network)
Group individual ports into a small “Virtual” network of their own to be independent of the other
ports. To add a VLAN group, press “Add Group” button, the new VLAN configuration window will
pop out, you can fill in the description in order to describe this VLAN Group, check on the port to be a
member to this VLAN Group, and press “Apply” button to execute the setting.
There are two group for VLAN Setting, each group have fixed setting to choose, check on the port to
be a member to the VLAN Port Group 1 or Port Group 2, and press “Apply” button to execute the
setting.
Once you want to modify the VLAN Group, check on the ID parameter, the ID VLAN configuration
window will pop out.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
When add a new Vlan, the members of default Vlan 1 are removed automatically.
Therefore, packets can only transmit among the member ports of new Vlan.
Packets can not fordward among the ports which are not included in the new vlan.
Trunk Setting
The Trunk function enables to cascade two devices with a double times bandwidth (up to 4000Mbps in
full duplex mode).
There is only one selection for the trunk setting, port 25 and port 26, or select “disable” for closing this
function.
Be sure that the selected trunk setting port must connect to the device with a same
VLAN group.
4.3 Maintenence
Status
Click on the “Status” to present the device status on this screen, it will show the System Status, Port
Status, VLAN Status and Trunk Status .
Press “Refresh” when you need to renew the posted information.
Statistics
The Statistic Menu screen will show the status of each port packet count.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
For Detail packet information, click on the ID parameter as Figure.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
System Settings
The System Setting includes the System name, Location name, Login Timeout, IP Address, Subnet
Mask and Gateway. Through the Web Management Utility, you can easily recognize the device by
using the System Name and the Location Name.
The Login Timeout is to set the idle time-out for security issue, when there is no action when running
the Web Smart Utility and the time is up, you must re-login to Web Smart Utility before you set the
Utility.
Fill up the IP Address, Subnet Mask and Gateway for the device.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
TRAP
The Trap Setting enables the device to monitor the Trap through the Web Management Utility, set the
Trap IP Address of the manager where the trap to be sent.
System Events: Monitoring the system’s trap.
• Device Bootup: a trap when booting up the system.
• Illegal Login: a trap when there is using a wrong password login, and it will record from where
the IP to be login.
Fiber Port Events: Monitoring the Fiber port status.
• Link Up/Link Down: a trap when there is linking status happens in fiber port.
• Abnormal* Receive Error: a trap when there are receive data error in fiber port.
• Abnormal* Transmit Error: a trap when there are transmit data error in fiber port.
Copper Port Events: Monitoring the copper port status.
• Abnormal* Receive Error: a trap when there are receive data error in copper port.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
• Abnormal* Transmit Error: a trap when there are transmit data error in copper port.
• Abnormal*: 50 error packet count within 10 seconds.
Abnormal*: 50 error packet count within 10 seconds.
Set Password
Password is the invaluable tool for the manager to secure Web Management Switch, use this function
to change the password.
If you forget the password, press the “Reset” button in the rear panel of the Switch, the current setting
includes VLAN, Port Setting… etc. will be lost and the Switch will restore to the default setting.
Backup Setting
The backup tools help you to backup the current setting of the Switch. Once you need to backup the
setting, press the “Backup” button to save the setting.
To restore a current setting file to the device, you must specify the backup file and press “Restore”
button to proceed the setting of the recorded file.
When restoring a recorded file, the current password will not be erased.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
Reset Settings
The Factory Reset button helps you to reset the device back to the default setting from the factory. Be
aware that the entire configuration will be reset, the IP address of the device will be set to default
setting 192.168.0.1 [password=admin].
Logout
When press this function, the web configuration will go back to first Login page.
All other names mentioned mat be trademarks or registered trademarks of their respective owners
23
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
APPENDIX A
RJ-45 Pin Specification
The following diagram and tables show the standard RJ-45 receptacle/connector and their pin
RJ-45 Connector pin assignment
Contact
Media Direct Interface
Signal
1
TX + (tx)
2
3
4
5
6
7
8
TX - (tx)
Rx + (rx)
Not used
Not used
Rx - (rx)
Not used
Not used
The standard cable, RJ-45 pin assignment.
The standard RJ-45 receptacle/connector.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
APPENDIX B
Technical Specifications
Standard
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3z 1000BASE-SX/LX Gigabit Ethernet
IEEE 802.3ab 1000BASE-T Gigabit Ethernet
IEEE 802.3x Full Duplex Flow Control
CSMA/CD
Protocol
Ethernet: 10Mbps (half duplex), 20Mbps (full-duplex)
Data Transfer Rate
Topology
Fast Ethernet: 100Mbps (half duplex), 200Mbps (full-duplex)
Gigabit Ethernet: 2000Mbps (full-duplex)
Star
10BASET: 2-pair UTP Cat. 3, 4, 5; up to 100m
100BASE-TX: 2-pair UTP Cat. 5; up to 100m
Network Cables
Number of Ports
1000BASE-T: 4-pair UTP Cat. 5; up to 100m
Fiber module: mini-GBIC Fiber module(1000BBASE-SX/LX)
24 × 10/100Mbps Auto-MDIX RJ45 ports
2 × 10/100/1000Mbps Auto-MDIX RJ45 ports
2 × mini-GBIC fiber slot
AC inputs
100-240V AC, 50-60 Hz internal universal power supply
19Watts (Max)
Power Consumption
Temperature
Humidity
Operating: 0° ~ 40° C, Storage: -10° ~ 70° C
Operating: 10% ~ 90%, Storage: 5% ~ 90%
440 x 200 x 44 mm (W x H x D)
Dimensions
EMI:
FCC Class A, CE Mark Class A, VCCI Class A
cUL(UL60950), CB(IEC60950)
Safety:
Transmission Method:
Store-and-forward
Filtering Address Table:
Packet Filtering / Forwarding
Rate:
4K entries per device
10Mbps Ethernet: 14,880/pps
100Mbps Fast Ethernet: 148,800/pps
1000Mbps Gigabit Ethernet: 1,488,000/pps
Automatic update
768K Bytes per device
MAC Address Learning:
RAM Buffer:
25
Download from Www.Somanuals.com. All Manuals Search And Download.
26-Port Dual Web Rack Switch
APPENDIX C
Support
If you have any problems with theSwitch , please consult this manual.
If you continue to have problems you should contact the dealer where you bought this Switch.
If you have any other questions you can contact the Atlantis Land company directly at the following
address:
Atlantis Land SpA
Viale De Gasperi, 122
20017 Mazzo di Rho(MI)
Tel: +39. 02.93907634(help desk) / +39. 02.93906085,
Fax: +39. 02.93906161
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|